Zenoah BC4500DW Owner`s manual

Zenoah BC4500DW Owner`s manual
BC4500DW
115 44 95-38 (110)
G
B
OWNER’S MANUAL
BRUSHCUTTERS
BC4500DW
Original Language
BC4500DW
SAFETY FIRST
Instructions contained in warnings within this
manual marked with a
symbol concern critical
points which must be taken into consideration to
prevent possible serious bodily injury, and for this
reason you are requested to read all such
instructions carefully and follow them without fail.
WARNINGS IN THE MANUAL
WARNING
This mark indicates instructions, which must be
followed in order to prevent accidents, which could
lead to serious bodily injury or death.
IMPORTANT
This mark indicates instructions, which must be
followed, or it leads to mechanical failure, breakdown,
or damage.
NOTE
This mark indicates hints or directions useful in the use
of the product.
1. Parts location
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
GB-2
Handle
Suspention point
Stop switch
Throttle cable
Throttle trigger
Shaft tube
Cutting attachment guard
Blade
Gear case
Starter knob
Fuel tank
Primer
Choke lever
Air cleaner cover
Contents
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Parts location....................................................2
Specifications ...................................................3
Warning labels on the machine ........................4
Symbols on the machine ..................................4
For safe operation ............................................5
Set up ...............................................................9
Fuel ................................................................10
Use .................................................................11
Maintenance...................................................13
Troubleshooting guide....................................14
Disposal..........................................................14
BC4500DW
2. Specification
MODEL CODE
Overall size
Length
Width
Height
Dry Weight
Engine Model
Displacement
Carburetor
Fuel
Fuel Tank capacity
Service range
Spark plug
Clutch system
Anti-vibration system
Housing
Handle-bracket
Gearhead
Neck angle
Reduction ratio
Blade Rotation
Handle Type
Throttle lever
Standard cutter
Harness Type
Quick release
Standard Accessories
Blade-cover
Tool-kit
Goggle
Owner's manual
Unit
BC4500DW
mm
mm
mm
Kg
1860
630
510
7.3
G45L-D
41.5
Diaphragm
Mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil)
0.94
5000~8000
BPMR7A
Two-shoe Centrifugal-Type
cc
litter
rpm
NOTE
G
B
Yes
Yes
deg
60
1.400
Counter-clockwise
Both
Trigger Type (With Safety-lock)
Steel-Blade
255-30T
Double
Yes
●
●
●
●
For transportation
Specifications are subject to change without notice.
GB-3
BC4500DW
3. Warning labels on the machine
(1)
(2)
(3)
(4)
(5)
(6)
(7)
15m (50ft)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Read owner’s manual before operating this machine.
Wear head, eye and ear protection.
Wear foot protection.
Wear gloves.
Beware of thrown objects.
Warning / Attention
Keep all children, bystanders and helpers 15 meters away from the machine.
If warning label peels off or becomes soiled
and impossible to read, you should contact the
dealer from which you purchased the product
to order new labels and affix them in the
required location(s).
Never modify your machine.
We won’t warrant the machine, if you use
the remodeled brushcutter or if you don’t
observe the proper usage written in the
manual.
4. Symbols on the machine
For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications,
please be careful not to make a mistake.
The port to refuel the “MIX GASOLINE”
Position: FUEL TANK CAP
The direction to close the choke
Position: ENGINE COVER
The direction to open the choke
Position: ENGINE COVER
GB-4
BC4500DW
5. For safe operation
WARNING
• A brushcutter or trimmer can be
dangerous if used incorrectly or
carelessly, and can cause serious or
fatal injury to the operater or others.
It is extremely important that you
read and understand the contents of
this Owner's manual.
• Under no circumstances may the
design of the machine be modified
without the permission of the
manufacturer. Always use genuine
accessories and parts. Nonauthorized modifications and/or
accessories or parts can result in
serious personal injury or the death
of the operator or others.
• When planning your work schedule,
allow plenty of time to rest. Limit the
amount of time over which the
product is to be used continuously
to somewhere around 30 ~ 40
minutes per session. Also try to
keep the total amount of work
performed in a single day under 2
hours or less.
• If you don’t observe the working
time, or working manner (See p5),
Repetitive Stress Injury(RSI) could
occur.
If you feel discomfort, redness and
swelling of your fingers or any other
part of your body, see a doctor
before getting worse.
■ BASIC SAFETY RULES
1. Never operate the product when you
are fatigued, ill, or upset, or under the
influence of madication that may make
you drowsy, or if you are under the
influence of alcohol or drugs.
2. Never use the product;
a: When the ground is slippery or when
you can't maintain a steady posture.
b: At night, at times of heavy fog, or at
any other times when your field of
vision might be limited and it would
be difficult to gain a clear view of the
working area.
c: During rain storms, during lightning
storms, at times of strong or galeforce winds, or at any other times
when weather conditions might make
it unsafe to use the product.
3. Wear the following protective
equipments when operating the
product.
a: Approved helmet to reduce the risk
of falling objects.
b: Approved ear protection to reduce
the risk of hearing loss.
c: Approved (ANSI Z87.1.) eye
protection and foot protection to
reduce the risk of injury associated
with thrown objects.
d: Face filter mask in dusty conditions
to reduce the risk of injury
associated with the inhalation of
dust.
e: Wear sturdy rubber-soled shoes or
shoes with some other form of antislip protection to help protect you
against falling.
f: Wear thick anti-vibration gloves to
reduce the risk of whitefinger
disease.
g: Do not wear loose clothing, scarves,
neck chains, unconfineed long hair,
and like to reduce the risk of injury
associated with objects being drawn
into air intake and rotating parts.
Personal protective equipment cannot
eliminate the risk of injury but it will
reduce the degree of injury.
4. The ignition system of your unit
produces an electromagnetic field of a
very low intensity. This field may
interfere with some pacemakers. To
reduce the risk of serious or fatal injury,
persons with pacemaker should consult
their physician and the pacemaker
munufacturer before operating this tool.
5. The area within a perimeter of 50 feet
(15 meters) of the person using the
product should be considered a
hazardous area into which no one
should enter. If necessary yellow
warning rope, warning signs should be
placed around the perimeter of the
area.
When work is to be performed
simultaneously by two or more
GB-5
G
B
BC4500DW
5. For safe operation
persons, care should also be taken to
constantly look around or otherwise
check for the presence and locations of
other people working so as to maintain
a distance between each person
sufficient to ensure safety.
6. Avoid using the product where stable
footing and balance are not assured.
7. All product service, other than the items
listed in the Owner's Manual, should be
performed by competent service
personnel.
8. Always shut off the engine before
setting it down.
9. Start the engine only in well ventilated
areas. Never start or run the engine
inside a closed room or building and
potentially explosive atmosphere.
Exhaust fumes contain dangerous
carbon monoxide.
10. Never to touch the spark plug or plug
cord while the engine is in operation
Doing so may result in being
subjected to an electrical shock.
11.Never to touch the muffler, spark plug,
other metallic parts of the engine or
engine cover while the engine is in
operation or immediately after shutting
down the engine. These metallic parts
and engine cover reach high
temperatures during operation and
doing so could result in serious burns.
12.To reduce the risk of injury associated
with contacting rotating parts, stop the
engine before installing or removing
attachments. Always disconnect the
spark plug before performing
maintenance or accessing movable
parts.
■ BEFORE USE
1. Each time before starting the engine,
inspect the entire unit to see if every
part is in good order and is securely
tightened in place. If any damage is
found in the fuel line, the exhaust line,
or the ignition wiring, do not use the
product until it has been repaired.
WARNING
2. Before starting operation, always
make sure that the cutting
attachment and the debris guard are
GB-6
properly installed and securely
fastened.
3. Check the condition of working area to
avoid any accident by hitting hidden
obstacles such as stumps, stones,
cans, or broken grass.
IMPORTANT
Remove any obstacle before beginning
work.
■ STARTING THE ENGINE
1. Keep bystanders and animals at least
50 feet (15 meters) away from the
operating point. If you are approached,
immediately stop the engine.
2. The product is equipped with
centrifugal clutch mechanism, so the
cutting attachment could rotate as soon
as the engine is started. When starting
the engine, place the product onto the
ground in a flat clear area and hold it
firmly in place so as to ensure that
neither the cutting part nor the throttle
come into contact with any obstacle
when the engine starts.
WARNING
Make sure the throttle is at idle
position. Never place the throttle into
the high speed position or half throttle
position (throttle lock position) when
starting the engine.
3. After starting the engine, check to
make sure that the cutting attachment
stops rotating when the throttle is
moved fully back to its original position
(idle position). If it continues to rotate
even after the throttle has been moved
fully back, turn off the engine and take
the unit to your authorized ZENOAH
servicing dealer for repair.
■ USING THE PRODUCT
IMPORTANT
Cut only materials recommended by the
manufacturer. And use only for tasks
explained in the manual.
1. Grip the handles firmly with both hands
BC4500DW
5. For safe operation
using your whole hand. Place your feet
slightly apart (slightly further apart than
the width of your shoulders) so that
your weight is distributed evenly across
both legs, and always be sure to
maintain a steady , even posture while
working.
2. Keep cutting attachment below waist
level.
3. Maintain the speed of the engine at the
level required to perform cutting work,
and never raise the speed of the
engine above the level necessary.
4. If you detect abnormal vibration or
noise during operation, promptly stop
the product and check whether
something has broken. If a breakedown
has occurred, do not operate the
product until the problem is fixed.
5. Keep all parts of your body away from
rotating cutting attachment.
6. Guard against hazardous situations at
all times. Warn adults to keep pets and
children away from the area. Be careful
if you are approached. Injury may result
from flying debris.
7. If someone calls out or otherwise
interrupts you while working, always be
sure to turn off the engine before
turning around.
8. After using the product and other
equipment, CLEAN UP!
2. Eliminate all sources of sparks or flame
(i.e. smoking, open flames, or work that
can cause sparks) in the areas where
fuel is mixed, poured, or stored.
3. Do not smoke while handling fuel or
while operating the product.
4. Do not refuel a hot engine.
5. Do not refuel a running engine.
6. Keep the handles dry, clean and free of
oil or fuel mixture.
7. Always store fuel in an approved
container designed for that purpose.
■ TRANSPORT
1. Drain the fuel from the fuel tank before
transporting or storing the product.
2. When hand-carrying the product, cover
over the cutting part, lift up the product
and carry it paying attention to the
blade.
3. Secure the unit carefully to prevent
movement when it is transported.
4. A unit that receives a strong shock
during transport and unloading may
malfunction.
1. Operate power equipment only at
reasonable hours not early in the
morning or late at night when people
might be disturbed. Comply with times
listed in local ordinances.
2. To reduce sound levels, limit the
number of pieces of equipment used at
any one time.
3. Operate the product at the lowest
possible throttle speed to do the job.
4. Check your equipment before
operation, especially the muffler, air
intakes and air filters.
■ FUEL SAFETY
1. Always use caution when handling fuel.
It is highly flammable. Wipe up all
spills, screw the fuel cap back tightly,
and then move the product at least 10
feet (3 meters) from the fueling point
before starting the engine.
■ STORAGE
1. Always store the product and fuel so
that there is no risk of leakages or
fumes coming into contact with sparks
or naked flames from electrical
equipment, electric moters,
relays/switches, boilers and the like.
2. When storing the product, the fuel tank
should be emptied.
3. When storing the product, choose a
space indoors free from moisture and
out of the reach of children.
■ AVOID NOISE PROBLEM
IMPORTANT
Check and follow the local regulations as
to sound level and hours of operations for
the product.
■ FOR PROTECTING YOUR BODY
FROM VIBRATION
WARNING
Prolonged use of the product,
exposing the operater to vibrations
GB-7
G
B
BC4500DW
5. For safe operation
and cold may produce whitefinger
disease (Raynaud's phenomenon),
which symptoms are tingling and
burning sensations followed by loss of
color and numbness in the fingers.
All factors which contribute to
whitefinger disease are not known, but
cold weather, smoking diseases or
physical conditions as well as long
periods of exposure to vibration are
mentioned as factors. In order to
reduce the risk of whitefinger disease,
the following precautions are strongly
recommended.
a: Keep your body warm. Never use the
product during rains.
b: Wear thick anti-vibration gloves.
c: Take more than 5 minutes of break in
warm place frequently.
d: Maintain a firm grip at all times, but do
not squeeze the handles with constant,
excessive pressures.
e: If you feel discomfort, redness and
swelling of your fingers or any other
part of your body, see a doctor before
getting worse.
■ MAINTENANCE
1. In order to maintain your product in
proper working order, perform the
maintenance and checking operations
described in the manual at regular
intervals.
2. Always be sure to turn off the engine
and disconnect the spark plug before
performing any maintenance or
checking procedures.
WARNING
The metallic parts and engine cover
reach high temperatures immediately
after stopping the engine.
3. Examine the product at intervals for
loose fasteners and rusted or damaged
parts. Use special care around the fuel
line, the muffler, and the ignition wiring.
4. When replacing the any other part, or
any lubricant, always be sure to use
only ZENOAH products or products
which have been certified by ZENOAH
for use with the ZENOAH product.
GB-8
5. In the event that any part must be
replaced or any maintenance or repair
work not described in this manual must
be performed, please contact a
representative from the store nearest
ZENOAH authorized servicing dealer
for assistance.
6. Do not use any accessory or
attachment other than those bearing
the ZENOAH mark and recommended
for the unit.
7. Under no circumstances should you
ever take apart the product or alter it in
any way. Doing so might result in the
product becoming damaged during
operation or the product becoming
unable to operate properly.
■ DISPOSAL
When disposing your machine, fuel or oil
for the machine, be sure to allow your
local regulations.
BC4500DW
6. Set up
■ ENGINE
Using attached 4 socket screws, secure the connection
firmly with equal force.
■ HANDLE
1. Remove the upper cap(1) from the bracket.
2. Loosen the 4 bolts on the clamp and insert the
handles equally. Retighten the bolts.
3. Put the handle assembly into the bracket and put the
upper cap(1) over it. Tighten the cap securely.
■ CONNECTING THROTTLE WIRE
1. Remove the air cleaner cover.
2. Connect the end of the throttle wire to the joint on
the top of the carburetor.
■ BLADE
1. Put the angled bar(1) into the side holes of the inner
holder and the gearcase.
2. Remove the nut (Lefthanded) and the outer
holder(3) from the gearshaft.
3. Put the blade onto the inner holder(2). Make the
marked side face the holder.
4. Put the outer holder(3) onto the gearshaft making
the recessed side face the blade.
5. Fasten the blade by the nut and the cover(4).
[Tightening torque]
14.7 to 19.6 N·m (150 to 200 kg·cm)
■ CLAMP THE THROTTLE WIRE
Bind the throttle wire to shaft tube(1) by clamp(2).
■ BLADE GUARD
Attach the guard on the shaft tube. Fix it with 2 bolts.
GB-9
G
B
BC4500DW
7. Fuel
■ Fuel
WARNING
• Gasoline is very flammable. Avoid smoking or
bringing any flame or sparks near fuel. Make
sure to stop the engine and allow it cool before
refueling the unit. Select outdoor bare ground for
fueling and move at least 3 m (10 ft) away from
the fueling point before starting the engine.
• The Zenoah engines are lubricated by oil specially
formulated for air-cooled 2-cycle gasoline engine
use. If Zenoah oil is not available, use an antioxidant added quality oil expressly labeled for aircooled 2-cycle engine use (JASO FC GRADE OIL or
ISO EGC GRADE).
• Do not use BIA or TCW (2-stroke water-cooling type)
mixed oil.
■ RECOMMENDED MIXING RATIO
GASOLINE 50 : OIL 1
(when using ZENOAH genuine oil)
• Exhaust emission are controlled by the
fundamental engine parameters and components
(eq., carburation, ignition timing and port timing)
without addition of any major hardware or the
introduction of an inert material during
combustion.
• These engines are certified to operate on unleaded
gasoline.
• Make sure to use gasoline with a minimum octane
number of 89RON (USA/Canada: 87AL).
• If you use a gasoline of a lower octane value than
prescribed, there is a danger that the engine
temperature may rise and an engine problem such
as piston seizing may consequently occur.
• Unleaded gasoline is recommended to reduce the
contamination of the air for the sake of your health
and the environment.
• Poor quality gasolines or oils may damage sealing
rings, fuel lines or fuel tank of the engine.
■ HOW TO MIX FUEL
WARNING
• Pay attention to agitation.
1. Measure out the quantities of gasoline and oil to be
mixed.
2. Put some of the gasoline into a clean, approved fuel
container.
GB-10
3. Pour in all of the oil and agitate well.
4. Pour in the rest of gasoline and agitate again for at
least one minute. As some oils may be difficult to
agitate depending on oil ingredients, sufficient
agitation is necessary for the engine to last long. Be
careful that, if the agitation is insufficient, there is an
increased danger of early piston seizing due to
abnormally lean mixture.
5. Put a clear indication on the outside of the container
to avoid mixing up with gasoline or other containers.
6. Indicate the contents on outside of container for
easy identification.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the cap on a
dustless place.
2. Put fuel into the fuel tank to 80% of the full capacity.
3. Fasten the fuel cap securely and wipe up any fuel
spillage around the unit.
WARNING
1. Select bare ground for fueling.
2. Move at least 10 feet (3 meters) away from the
fueling point before starting the engine.
3. Stop the engine before refueling the unit. At that
time, be sure to sufficiently agitate the mixed
gasoline in the container.
■ FOR YOUR ENGINE LIFE, AVOID:
1. FUEL WITH NO OIL (RAW GASOLINE) – It will
cause severe damage to the internal engine parts
very quickly.
2. GASOHOL – It can cause deterioration of rubber
and/or plastic parts and disruption of engine
lubrication.
3. OIL FOR 4-CYCLE ENGINE USE – It can cause
spark plug fouling, exhaust port blocking, or piston
ring sticking.
4. Mixed fuels which have been left unused for a
period of one month or more may clog the
carburetor and result in the engine failing to operate
properly.
5. In the case of storing the product for a long period of
time, clean the fuel tank after rendering it empty.
Next, activate the engine and empty the carburetor
of the composite fuel.
6. In the case of scrapping the used mixed oil
container, scrap it only at an authorized repository
site.
NOTE
• As for details of quality assurance, read the
description in the section Limited Warranty carefully.
Moreover, normal wear and change in product with
no functional influence are not covered by the
warranty. Also, be careful that, if the usage in the
instruction manual is not observed as to the mixed
gasoline, etc. described therein, it may not be
covered by the warranty.
BC4500DW
8. Use
■ STARTING THE ENGINE
Take care that the cutting head will start rotating upon
the engine starts.
1. Push the primer pump(1) several times until
overflown fuel flows out in the clear tube.
2. Move the choke lever(2) to the closed position.
G
B
Engine idling speed:
It is normal that the engine keeps running without
the blade rotation, when the throttle lever is
released. When the engine speed is too high or too
slow, readjust the idle set screw (2).
3. Set the stop switch(a) to the " I " position. Set the
throttle trigger to the start position (1-2).
(2)
(a)
(1)
■ SWIVEL LOCK
a) When the unit is not hung down with the harness, as
in transportation, use the swivel lock to prevent the
engine from roll down.
b) To lock the swivel, turn the wing nut(1) clockwise.
4. Place the unit on a flat, firm place. Keep the cutting
head clear of everything around it.
5. While holding the unit firmly, pull out the starter rope
quickly.
c) For normal operation, keep the wing nut loose.
6. After the engine has started, open the choke
guradually and allow the engine to warm up. Pull the
throttle lever to unlock it.
■ CUTTING WORK
• By using the shoulder strap(1), hang the unit on your
right side. Adjust the strap length so that the cutting
head may become parallel to the ground.
■ STOPPING THE ENGINE
1. Release the throttle trigger.
2. Move the stop switch to the "O" position.
■ ADJUSTMENTS
Throttle cable:
The normal play is 1 or 2 mm when measured at the
carburetor side end. Readjust with the cable
adjuster(1) as re-quired.
• Choose a suitable recommended cutting attachment
according to the object to be cut. Never use other
cutting attachment not approved by Husqvarna
Zenoah.
GB-11
BC4500DW
8. Use
When using a metal blade:
1. Check the bolt to fasten the blade and be sure the
bolt has on fault, and no abrasion.
2. Be sure that the blade and the holder have been
fastened according to instruction and the blade turns
smoothly without abnormal noise. The rotating parts
fastened incorrectly may cause serious accident to
the operator.
3. Cutting method:
a) Use the front left side for cutting.
b) Guide the blade from your right to left with it tilted
slightly to your left.
c) When mowing a wide area, start working from
your left end to avoid interference of cut grass.
d) The blade may be seized by weeds if the engine
speed is too low, or the blade cuts too, deep into
weeds. Adjust the engine speed and cutting depth
according to the condition of object.
WARNING
For your health and to prevent the risk from
vibration, refrairr from working for a long time at
the cold temperature.
GB-12
BC4500DW
9. Maintenance
WARNING
Before cleaning, inspecting, or repairing the unit,
make sure that the engine has stopped and is cool.
■ BLADE
Check the blade and the fasteners for looseness,
cracking, or bending.
■ AIR FILTER
A clogged air filter will reduce the engine performance.
Check periodically and clean the filter element in warm,
soapy water as required. Dry completely before
installing. If the element is broken or shrunk, replace
with a new one.
■ GEARCASE
• Supply multi-purpose grease at every 25 hours of
use.
• Remove the bolt of the grease nipple and the bolt
opposite side of the grease nipple. Install new
grease into the grease nipple to arrange for old
grease to exit from the opposite side.
■ MAINTENANCE BEFORE STORAGE
• Old fuel left in the carburetor may cause starting
failure. When a series of operation finished, make
sure to empty the fuel tank and drain the carburetor.
• Check all parts and the functions. If the failured or
damaged parts have been found, replace them with
new ones.
■ FUEL FILTER
When the engine runs short of fuel supply, check the
fuel strainer for blockage.
■ SPARK PLUG
Starting failure and mis-firing are often caused by a
fouled spark plug. Periodically clean the spark plug,
and replace with a new one as required.
Type of Plug
NGK BPMR7A
Spark Gap
0.6 ~ 0.7 mm
GB-13
G
B
BC4500DW
10. Troubleshooting guide
Case 1. Starting failure
CHECK
fuel tank
➞
PROBABLE CAUSES
incorrect fuel
➞
ACTION
drain it and with correct fuel
fuel filter
➞
fuel filter is clogged
➞
clean
carburetor adjustment screw
➞
out of normal range
➞
adjust to normal range
sparking (no spark)
spark plug
➞
spark plug is fouled/wet
➞
clean/dry
➞
plug gap is incorrect
➞
correct (GAP: 0.6 – 0.7 mm)
➞
disconnected
➞
retighten
Case 2. Engine starts but does not keep running/Hard re-starting.
CHECK
PROBABLE CAUSES
fuel tank
➞ incorrect fuel or staled fuel
➞
ACTION
drain it and with correct fuel
carburetor adjustment screw
➞
out of normal range
➞
adjust to normal range
muffler,cylinder (exhaust port)
➞
carbon is built-up
➞
consult with the repair specialty store
air cleaner
➞
clogged with dust
➞
air blow or wash
cylinder fin, fan cover
➞
clogged with dust
➞
consult with the repair specialty store
When your unit seems to need further service, please consult with our ZENOAH service shop in your area.
11. Disposal
• When you dispose of the machine, do not disassemble the machine.
• When you dispose of the machine, fuel, oil, be sure to follow your local regulations.
GB-14
BC4500DW
Limited warranty
Should any failure occur on the product under normal
operating conditions within the applicable warranty
period, the failed part will be replaced or repaired free
of charge by a ZENOAH authorized dealer.
THE COMPANY IS LIABLE FOR DAMAGES TO
OTHER ENGINE COMPONENTS CAUSED BY THE
FAILURE OF A WARRANTED PART STILL UNDER
WARRANTY.
WARRANTY PERIOD: Six (6) months after purchased
by end-user subject to 12 months from produced month
(30 days If used for rental purpose)
THE WARRANTY DOES NOT APPLY TO THOSE
UNITS WHICH HAVE BEEN DAMAGED BY
NEGLIGENCE OF INSTRUCTION LISTED IN THE
OWNER/OPERATOR MANUAL FOR PROPER USE
AND MAINTENANCE OF THE UNITS ACCIDENT
MISHANDLING, ALTERATION, ABUSE, IMPROPER
LUBRICATION, USE OF ANY PARTS OR
ACCESSORIES OTHER THAN THOSE SPECIFIED
BY THE COMPANY, OR OTHER CAUSES BEYOND
THE COMPANY’S CONTROL.
THE PURCHASER SHALL BEAR COSTS OF
TRANSPORTING THE UNIT TO AND FROM THE
ZENOAH DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR
DIAGNOSTIC LABOR WHICH LEADS TO THE
DETERMINATION THAT A WARRANTED PART IS
DEFECTIVE, IF THE DIAGNOSTIC WORK IS
PERFORMED AT THE ZENOAH DEALER.
THE PURCHASER OR OWNER IS RESPONSIBLE
FOR THE PERFORMANCE OF THE REQUIRED
MAINTENANCE AS DEFINED BY THE
MANUFACTURER IN THE OWNER/OPERATOR
MANUAL.
ANY WARRANTED PART WHICH IS NOT
SCHEDULED FOR REPLACEMENT AS REQUIRED
MAINTENANCE, OR WHICH IS SCHEDULED ONLY
FOR REGULAR INSPECTION TO THE EFFECT OF
REPAIR OR “REPLACE AS NECESSARY” SHALL BE
WARRANTED FOR THE WARRANTY PERIOD. ANY
WARRANTED PART WHICH IS SCHEDULED FOR
REPLACEMENT AS REQUIRED MAINTENANCE
SHALL BE WARRANTED FOR THE PERIOD OF TIME
UP TO THE FIRST SCHEDULED REPLACEMENT
POINT FOR THE PART.
ANY REPLACEMENT PART THAT IS EQUIVALENT
IN PERFORMANCE AND DURABILITY MAY BE
USED IN NON-WARRANTY MAINTENANCE OR
REPAIRS, AND SHALL NOT REDUCE THE
WARRANTY OBLIGATION OF THE COMPANY.
THIS WARRANTY DOES NOT COVER THOSE
PARTS REPLACED BY NORMAL WEAR OR
HARMLESS CHANGES IN THEIR APPEARANCE.
THERE ARE NO OTHER EXPRESS WARRANTIES.
ANY IMPLIED WARRANTY is limited to the duration of
the limited warranty. Otherwise, this limited warranty is
in lieu of all other expressed or implied warranties,
including any warranty of FITNESS FOR A
PARTICULAR PURPOSE OR USE and any implied
warranty MERCHANTABILITY otherwise applicable to
this product.
LIABILITIES FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGE UNDER ANY AND ALL
WARRANTIES ARE EXCLUDED.
IF YOU NEED TO OBTAIN MORE INFORMATION,
PLEASE CALL YOUR NEAREST SERVICE CENTER,
OR CHECK PLEASE ZENOAH WEB SITE
http://www.zenoah.net
GB-15
G
B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement