Compaq Presario,Presario 735 System information

Add to my manuals
139 Pages

advertisement

Compaq Presario,Presario 735 System information | Manualzz
HP G7000 Notebook PC and
Compaq Presario C700 Notebook PC
Maintenance and Service Guide
Downloaded from LpManual.com Manuals
© Copyright 2007 Hewlett-Packard
Development Company, L.P.
Intel, Celeron, and Core are trademarks or
registered trademarks of Intel Corporation or
its subsidiaries in the United States and other
countries. Microsoft, Windows, and
Windows Vista are either trademarks or
registered trademarks of Microsoft
Corporation in the United States and/or other
countries. SD Logo is a trademark of its
proprietor.
The information contained herein is subject to
change without notice. The only warranties
for HP products and services are set forth in
the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
Second Edition: December 2007
First Edition: July 2007
Document Part Number: 447381-002
Downloaded from LpManual.com Manuals
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact
the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the AC
adapter comply with the user-accessible surface temperature limits defined by the International Standard
for Safety of Information Technology Equipment (IEC 60950).
iii
Downloaded from LpManual.com Manuals
iv
Safety warning notice
Downloaded from LpManual.com Manuals
Table of contents
1 Product description
2 External component identification
Top components ...................................................................................................................... 5
Display components .................................................................................................. 5
Buttons and speakers ................................................................................................. 6
Keys ........................................................................................................................ 7
Lights ....................................................................................................................... 8
TouchPad ................................................................................................................. 9
Front components ................................................................................................................... 10
Right-side components ............................................................................................................ 10
Left-side components ............................................................................................................... 11
Bottom components ................................................................................................................ 12
3 Illustrated parts catalog
Serial number location ............................................................................................................ 13
Computer major components ................................................................................................... 14
Display assembly components ................................................................................................. 20
Plastics Kit ............................................................................................................................. 22
Mass storage devices ............................................................................................................. 23
Miscellaneous parts ................................................................................................................ 24
Sequential part number listing .................................................................................................. 26
4 Removal and replacement procedures
Preliminary replacement requirements ....................................................................................... 32
Tools required ......................................................................................................... 32
Service considerations ............................................................................................. 32
Plastic parts ............................................................................................. 32
Cables and connectors ............................................................................. 33
Drive handling ......................................................................................... 33
Grounding guidelines .............................................................................................. 34
Electrostatic discharge damage .................................................................. 34
Packaging and transporting guidelines ........................................ 35
v
Downloaded from LpManual.com Manuals
Workstation guidelines .............................................................. 35
Equipment guidelines ................................................................. 36
Unknown user password .......................................................................................... 37
Component replacement procedures ........................................................................................ 38
Serial number ......................................................................................................... 38
Computer feet ......................................................................................................... 39
Battery ................................................................................................................... 40
Hard drive ............................................................................................................. 41
Memory module ...................................................................................................... 43
WLAN module ........................................................................................................ 45
Optical drive .......................................................................................................... 48
Keyboard ............................................................................................................... 50
Switch cover ........................................................................................................... 53
Display assembly .................................................................................................... 55
Camera module ...................................................................................................... 60
Top cover ............................................................................................................... 62
Caps lock LED board ............................................................................................... 64
USB board ............................................................................................................. 66
Fan ....................................................................................................................... 68
Speakers ................................................................................................................ 70
System board ......................................................................................................... 72
RTC battery ............................................................................................................ 75
Card reader board .................................................................................................. 77
Heat sink ............................................................................................................... 79
Processor ............................................................................................................... 81
Power connector cable ............................................................................................ 83
5 Setup Utility
Starting the Setup Utility .......................................................................................................... 84
Changing the language of the Setup Utility ............................................................................... 84
Navigating and selecting in the Setup Utility .............................................................................. 85
Displaying system information .................................................................................................. 85
Restoring default settings in the Setup Utility .............................................................................. 85
Using advanced Setup Utility features ....................................................................................... 86
Closing the Setup Utility .......................................................................................................... 86
Setup Utility menus ................................................................................................................. 86
6 Specifications
Computer specifications .......................................................................................................... 88
15.4-inch, WSXGA, BrightView display specifications ................................................................ 89
Hard drive specifications ........................................................................................................ 90
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive specifications ................................ 91
System DMA specifications ...................................................................................................... 92
vi
Downloaded from LpManual.com Manuals
System memory map specifications .......................................................................................... 92
System interrupt specifications ................................................................................................. 93
System I/O address specifications ............................................................................................ 94
7 Screw listing
Phillips PM2.0×5.0 captive screw ............................................................................................ 97
Phillips PM3.0×3.0 screw ....................................................................................................... 98
Black Phillips PM2.0×3.0 screw ............................................................................................... 99
Black Phillips PM2.0×4.0 screw ............................................................................................. 100
Phillips PM2.5×9.0 screw ..................................................................................................... 102
Phillips PM2.5×4.0 screw .....................................................................................................
Phillips PM2.5×7.0 screw .....................................................................................................
Silver Phillips PM2.0×4.0 screw ............................................................................................
Phillips PM2.5×6.0 captive screw ..........................................................................................
104
107
108
109
8 Backup and recovery
Recovering system information ...............................................................................................
Backing up your information ...................................................................................
When to back up ...................................................................................
Backup suggestions ................................................................................
Using system restore points .....................................................................................
When to create restore points ..................................................................
Create a system restore point ...................................................................
Restore to a previous date and time ..........................................................
Creating recovery discs .........................................................................................
Performing a recovery ...........................................................................................
Recovering from the recovery discs ...........................................................
Recovering from the partition on the hard drive ..........................................
110
110
110
111
111
111
111
113
113
114
114
114
9 Connector pin assignments
Audio-out (headphone) .........................................................................................................
Audio-in (microphone) ..........................................................................................................
External monitor ...................................................................................................................
RJ-11 (modem) .....................................................................................................................
RJ-45 (network) ....................................................................................................................
115
115
116
117
117
S-Video-out .......................................................................................................................... 118
Universal Serial Bus .............................................................................................................. 118
10 Power cord set requirements
Requirements for all countries or regions ................................................................................. 119
Requirements for specific countries or regions .......................................................................... 120
vii
Downloaded from LpManual.com Manuals
11 Recycling
Battery ................................................................................................................................ 121
Display ............................................................................................................................... 121
Index ............................................................................................................................... 127
viii
Downloaded from LpManual.com Manuals
1
Product description
Category
Description
HP G7000
Notebook PC
Product Name
HP G7000 Notebook PC
√
Compaq Presario C700 Notebook PC
Processors
Compaq Presario
C700 Notebook
PC
√
Intel® Core™ 2 Duo processors
T8300 2.40-GHz processor, 3-MB L2 cache,
800-MHz FSB
√
√
T8100 2.10-GHz processor, 3-MB L2 cache,
800-MHz FSB
√
√
T7250 2.00-GHz processor, 2-MB L2 cache,
800-MHz front side bus (FSB)
√
√
T7100 1.80-GHz processor, 2-MB L2 cache,
800-MHz FSB
√
√
T5750 2.00-GHz processor, 2-MB L2 cache,
667-MHz FSB
√
√
T5450 1.67-GHz processor, 2-MB L2 cache,
667-MHz FSB
√
√
T2370 1.73-GHz processor, 1-MB L2 cache,
667-MHz FSB
√
√
T2330 1.60-GHz processor, 1-MB L2 cache,
667-MHz FSB
√
√
T2310 1.46-GHz processor, 1-MB L2 cache,
667-MHz FSB
√
√
550 2.00-GHz processor, 1-MB L2 cache,
533-MHz FSB
√
√
540 1.86-GHz processor, 1-MB L2 cache,
533-MHz FSB
√
√
530 1.73-GHz processor, 1-MB L2 cache,
533-MHz FSB
√
√
Northbridge: Intel GM965
√
Northbridge: GL960
√
Intel Core Duo processors
Intel Celeron® M processors
Chipset
√
1
Downloaded from LpManual.com Manuals
Category
Graphics
Description
HP G7000
Notebook PC
Compaq Presario
C700 Notebook
PC
Southbridge: Intel ICH8m
√
√
Universal memory architecture (UMA)
√
√
●
Up to 64-MB of graphics subsystem
memory on computer models with 512MB system RAM
●
Up to 128-MB of graphics subsystem
memory on computer models with 1024MB or more system RAM
●
Up to 256-MB of graphics subsystem
memory on computer models with 1024MB or more system RAM
Memory size change is dynamic.
Panel
15.4-inch, WSXGA with BrightView
√
√
Memory
2 SODIMM slots
√
√
Customer-accessible/upgradable
√
√
Supports up to 2 GB of system RAM
√
√
DDRII PC2-5300 (667-MHz)
√
√
Support for:
√
√
Support for 9.5-mm, 2.5-inch hard drives
√
√
Serial ATA
√
√
Support for the following drives:
√
√
Fixed (removal of 1 screw required)
√
√
Parallel ATA
√
√
12.7-mm tray load
√
√
Support for:
√
√
Hard drives
Optical drives
2
Chapter 1 Product description
Downloaded from LpManual.com Manuals
●
1024 (1024 × 1, 512 × 2)
●
512 (512 × 1, 256 × 2)
●
256 (256 × 1)
●
160-GB, 5400-rpm
●
120-GB, 5400-rpm
●
80-GB, 5400-rpm
●
DVD±RW and CD-RW Super Multi
Double-Layer Combo Drive with
LightScribe
●
DVD±RW and CD-RW Super Multi
Double-Layer Combo Drive
●
DVD-CD/RW Combo Drive
Category
Description
HP G7000
Notebook PC
Compaq Presario
C700 Notebook
PC
Diskette drive
Support for external USB drive only
√
√
Camera
Low-light, VGA camera
√
√
Fixed (no tilt)
√
√
640 × 480 by 20 frames per second
√
√
Microphone
One omnidirectional monoaural microphone
√
√
Audio
Azalia high-definition (HD) audio
√
√
HP-branded Altec Lansing speakers
√
Presario-branded Altec Lansing speakers
√
Modem
56K V.92 data/fax modem
√
√
Ethernet
Integrated 10/100 network interface card
(NIC)
√
√
Ethernet cable not included
√
√
Wireless
External media card
Ports
Docking
Integrated wireless local area network (WLAN) options by way of wireless
module:
Intel PRO Wireless 3945 802.11a/b/g and
802.11b/g
√
√
Broadcom 802.11a/b/g
√
√
Atheros AR2425 WLAN b/g
√
√
Support for 2.4- and 5.0-GHz antenna
integrated into the display assembly
√
√
Digital Media Slot, supports SD, MMC, MS,
MSP, SD I/O, xD Type H, and xD Type M
√
√
Support for miniature versions of SD, MMC,
MS Duo with adapter (adapter is not included)
√
√
Audio-in (mono microphone)
√
√
Audio-out (stereo headphone)
√
√
RJ-11 (modem)
√
√
RJ-45 (Ethernet, includes link and activity
lights)
√
√
S-Video-out (include component video support) √
√
USB (3)
√
√
VGA (Dsub, 15-pin) supporting 1600 × 1200 √
external resolution @ 75Hz, hot plug/unplug,
and autodetect for correct output to wideaspect vs. standard-aspect video
√
2-pin, 65-W AC power
√
√
No docking
√
√
3
Downloaded from LpManual.com Manuals
Category
Description
HP G7000
Notebook PC
Compaq Presario
C700 Notebook
PC
Keyboard/pointing
devices
12.0-inch keyboard
√
√
TouchPad
√
√
2 rubber dome TouchPad buttons with scissor
structure
√
√
4-way scroll
√
√
Taps enabled as default
√
√
6-cell 2.20-Ah Li-ion battery
√
√
65-W AC adapter with localized cable plug
support (2-wire plug with ground pin, supports
2-pin DC connector)
√
√
Security
Security cable slot
√
√
Operating system
Preinstalled:
Free DOS
√
√
Windows Vista® Home Basic (32-bit)
√
√
Windows Vista Premium (32-bit)
√
√
AC adapter
√
√
Battery (system)
√
√
Hard drive
√
√
Memory module
√
√
Optical drive
√
√
WLAN module
√
√
Power requirements
Serviceability
4
Chapter 1 Product description
Downloaded from LpManual.com Manuals
End-user replaceable parts:
2
External component identification
Top components
Display components
Item
Component
Description
(1)
Internal display switch
Turns off the display if the display is closed while the
computer is turned on.
(2)
Integrated camera light (select models only)
On: The integrated camera is in use.
(3)
Integrated camera (select models only)
Records video and captures still photographs.
(4)
Internal microphone
Records sound.
NOTE: If there is a microphone icon next to each
microphone opening, the computer has internal
microphones.
*To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies
to your country or region. These notices are located in Help and Support.
Top components
Downloaded from LpManual.com Manuals
5
Buttons and speakers
Item
Component
Description
(1)
Speakers (2)
Produce sound.
(2)
Wireless button
Turns the wireless feature on or off, but does not create a
wireless connection.
NOTE: To establish a wireless connection, a wireless
network must already be set up.
(3)
Power button*
●
When the computer is off, press the button to turn on
the computer.
●
When the computer is on, press the button to initiate
Sleep.
●
When the computer is in the Sleep state, press the
button briefly to exit Sleep.
●
When the computer is in Hibernation, press the button
briefly to exit Hibernation.
If the computer has stopped responding and Windows®
shutdown procedures are ineffective, press and hold the
power button for at least 5 seconds to turn off the computer.
To learn more about power settings, select Start > Control
Panel > System and Maintenance > Power
Options.
(4)
Volume mute hotkey
Press fn+home to mute and restore speaker sound.
(5)
Volume up hotkey
Press fn+pg up to increase speaker volume.
(6)
Volume down hotkey
Press fn+pg dn to decrease speaker volume.
*This table describes factory settings. For information about changing factory settings, refer to the user guides located in Help
and Support.
6
Chapter 2 External component identification
Downloaded from LpManual.com Manuals
Keys
Item
Component
Function
(1)
esc key
Displays system information when pressed in combination
with the fn key.
(2)
fn key
Executes frequently used system functions when pressed in
combination with a function key or the esc key.
(3)
Windows logo key
Displays the Windows Start menu.
(4)
Windows applications key
Displays a shortcut menu for items beneath the pointer.
(5)
Embedded numeric keypad keys
Can be used like the keys on an external numeric keypad.
(6)
Function keys
Execute frequently used system functions when pressed in
combination with the fn key.
Top components
Downloaded from LpManual.com Manuals
7
Lights
Item
Component
Description
(1)
Power lights (2)*
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off or in Hibernation.
●
On: A battery is charging.
●
Blinking: A battery that is the only available power
source has reached a low battery level or a critical
battery level.
●
Off: If the computer is plugged into an external power
source, the light is turned off when all batteries in the
computer are fully charged. If the computer is not
plugged into an external power source, the light stays
off until the battery reaches a low battery level.
(2)
Battery light
(3)
Drive light
Blinking: The hard drive or optical drive is being accessed.
(4)
Wireless lights (2)†
●
Blue: An integrated wireless device, such as a WLAN
device, is turned on.
●
Amber: An integrated wireless device is turned off.
(5)
Caps lock light
On: Caps lock is on.
(6)
Num lock light
On: Num lock is on or the embedded numeric keypad is
enabled.
*The 2 power lights display the same information. The light on the power button is visible only when the computer is open. The
power light on the front of the computer is visible whether the computer is open or closed.
†The 2 wireless lights display the same information. The light on the wireless button is visible only when the computer is open.
The wireless light on the front of the computer is visible whether the computer is open or closed.
8
Chapter 2 External component identification
Downloaded from LpManual.com Manuals
TouchPad
Item
Component
Function
(1)
TouchPad light
●
Blue: TouchPad is enabled.
●
Amber: TouchPad is disabled.
(2)
TouchPad*
Moves the pointer and selects or activates items on the
screen.
(3)
TouchPad horizontal scroll zone*
Scrolls left or right.
(4)
Left TouchPad button*
Functions like the left button on an external mouse.
(5)
Right TouchPad button*
Functions like the right button on an external mouse.
(6)
TouchPad vertical scroll zone*
Scrolls up or down.
(7)
TouchPad on/off button
Enables/disables the TouchPad.
*This table describes factory settings. To view or change pointing device preferences, select Start > Control Panel >
Hardware and Sound > Mouse.
Top components
Downloaded from LpManual.com Manuals
9
Front components
Item
Component
Function
(1)
Audio-out (headphone) jack
Produces sound when connected to optional powered stereo
speakers, headphones, ear buds, a headset, or television
audio.
(2)
Audio-in (microphone)
Connects an optional computer headset microphone, stereo
array microphone, or monaural microphone.
Right-side components
Item
Component
Function
(1)
USB ports
Connect optional USB devices.
(2)
Optical drive
Reads optical discs, and, on select models, also writes to
optical discs.
(3)
Optical drive light
On: The optical drive is being accessed.
(4)
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a
deterrent, but may not prevent the computer from being
mishandled or stolen.
10
Chapter 2 External component identification
Downloaded from LpManual.com Manuals
Left-side components
Item
Component
Function
(1)
Power connector
Connects an AC adapter.
(2)
Vents (4)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(3)
RJ-11 (modem) jack
Connects a modem cable.
(4)
RJ-45 (network) jack
Connects a network cable.
(5)
External monitor port
Connects an external VGA monitor or projector.
(6)
S-Video-out jack
Connects an optional S-Video device such as a television,
VCR, camcorder, overhead projector, or video capture
card.
(7)
USB port
Connects optional USB devices.
(8)
Digital Media Slot
Supports the following optional digital card formats:
●
Memory Stick (MS)
●
Memory Stick Pro (MSP)
●
MultiMediaCard (MMC)
●
Secure Digital Input/Output (SD I/O)
●
Secure Digital (SD) Memory Card
●
xDPicture Card (XD)
●
xD-Picture Card (XD) Type H
●
xD-Picture Card (XD) Type M
Left-side components
Downloaded from LpManual.com Manuals
11
Bottom components
Item
Component
Function
(1)
Battery bay
Holds the battery.
(2)
Battery release latch
Releases the battery from the battery bay.
(3)
Memory/wireless module compartment
Contains 2 memory slots and a wireless module slot.
CAUTION: To prevent an unresponsive system, replace
the wireless module only with a wireless module authorized
for use in the computer by the governmental agency that
regulates wireless devices in your country or region. If you
replace the module and then receive a warning message,
remove the module to restore computer functionality, and
then contact technical support through Help and Support.
(4)
Hard drive bay
Holds the hard drive.
(5)
Vents (3)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
12
Chapter 2 External component identification
Downloaded from LpManual.com Manuals
3
Illustrated parts catalog
Serial number location
When ordering parts or requesting information, provide the computer serial number and model number
located on the bottom of the computer.
Serial number location
Downloaded from LpManual.com Manuals
13
Computer major components
14
Chapter 3 Illustrated parts catalog
Downloaded from LpManual.com Manuals
Item
Description
Spare part number
(1)
15.4-inch, WSXGA BrightView display assemblies (include 2 microphones and 2 wireless antenna transceivers
and cables)
For use only with HP G7000 computer models:
●
Without a Web camera
454932-001
●
With a Web camera
462455-001
For use only with Compaq Presario C700 computer models:
●
Without a Web camera
454934-001
●
With a Web camera
462456-001
(2)
Switch cover (includes power button board and cable, wireless button board and cable,
and numeric lock LED board and cable)
(3)
Keyboards
454940-001
Belgium
454954-A41
Brazil
454954-201
Czechoslovakia
454954-221
Denmark, Finland, Norway, and Sweden
454954-DH1
France
454954-051
French Canada
454954-121
Germany
454954-041
Greece
454954-151
Israel
454954-BB1
Italy
454954-061
Japan
454954-291
Latin America
454954-161
The Netherlands and Europe
454954-B31
Portugal
454954-131
Russia
454954-251
Saudi Arabia
454954-171
South Korea
454954-AD1
Spain
454954-071
Switzerland
454954-BG1
Taiwan
454954-AB1
Thailand
454954-281
Turkey
454954-141
The United Kingdom
454954-031
The United States
454954-001
Computer major components
Downloaded from LpManual.com Manuals
15
Item
Description
(4)
Top cover (includes TouchPad and cable)
Spare part number
For use only in computer models not equipped with a Web camera
454936-001
For use only in computer models equipped with a Web camera
466649-001
(5)
Caps lock LED board (includes cable)
454948-001
(6)
Speakers
454946-001
(7)
Fan
454944-001
(8)
Power connector cable
454945-001
Plastics Kit (see Plastics Kit on page 22 for more information)
454937-001
(9a)
Hard drive bay cover
(9b)
Memory/wireless module compartment cover
(10)
System boards (include replacement thermal material and modem cable)
For use in computer models not equipped with a Web camera:
●
Equipped with Intel Core 2 Duo and Core Duo processors and a card reader board
453494-001
●
Equipped with Intel Core 2 Duo and Core Duo processors, but not a card reader board
445882-001
●
Equipped with Intel Celeron M processors and a card reader board
453495-001
●
Equipped with Intel Celeron M processors, but not a card reader board
454883-001
For use in computer models equipped with a Web camera:
16
●
Equipped with Intel Core 2 Duo and Core Duo processors and a card reader board
462439-001
●
Equipped with Intel Core 2 Duo and Core Duo processors, but not a card reader board
462441-001
●
Equipped with Intel Celeron M processors and a card reader board
462440-001
●
Equipped with Intel Celeron M processors, but not a card reader board
462442-001
Modem cable (not illustrated)
454950-001
(11)
USB board (includes cable)
454941-001
(12)
Card reader board (for use only with system boards with spare part numbers
453494-001, 453495-001, 462439-001, and 462440-001)
454949-001
(13)
Processors (include replacement thermal material)
Intel Core 2 Duo T8300 (2.40-GHz, 3 MB of L2 cache, 800-MHz FSB)
459798-001
Intel Core 2 Duo T8100 (2.10-GHz, 3 MB of L2 cache, 800-MHz FSB)
459797-001
Intel Core 2 Duo T7250 (2.00-GHz, 2 MB of L2 cache, 800-MHz FSB)
454320-001
Intel Core 2 Duo T7100 (1.80-GHz, 2 MB of L2 cache, 800-MHz FSB)
448149-001
Intel Core Duo T5750 (2.00-GHz, 2 MB of L2 cache, 667-MHz FSB)
462353-001
Intel Core Duo T5450 (1.67-GHz, 2 MB of L2 cache, 667-MHz FSB)
451597-001
Intel Core Duo T2370 (1.73-GHz, 1 MB of L2 cache, 667-MHz FSB)
462354-001
Intel Core Duo T2330 (1.60-GHz, 1 MB of L2 cache, 667-MHz FSB)
455944-001
Chapter 3 Illustrated parts catalog
Downloaded from LpManual.com Manuals
Item
Description
Spare part number
Intel Core Duo T2310 (1.46-GHz, 1 MB of L2 cache, 667-MHz FSB)
455943-001
Intel Celeron M 550 (2.00-GHz, 1 MB of L2 cache, 533-MHz FSB)
454322-001
Intel Celeron M 540 (1.86-GHz, 1 MB of L2 cache, 533-MHz FSB)
454321-001
Intel Celeron M 530 (1.73-GHz, 1 MB of L2 cache, 533-MHz FSB)
455437-001
(14)
Heat sink (includes thermal material)
454943-001
(15)
RTC battery
454947-001
(16)
6-cell, 2.20-Ah, 47-Wh Li-ion battery
454931-001
(17)
Base enclosures (includes 6 base rubber feet)
(18)
For use only with computer models equipped with a card reader board
454939-001
For use only with computer models not equipped with a card reader board
454938-001
Rubber Foot Kit (includes 6 base enclosure rubber feet)
454952-001
WLAN modules
Broadcom 802.11a/b/g WLAN modules:
●
For use in Antigua and Barbuda, Argentina, Australia, the Bahamas, Barbados, Brunei,
Canada, Chile, the Dominican Republic, Guam, Guatemala, Hong Kong, India,
Indonesia, Malaysia, Mexico, New Zealand, Panama, Paraguay, Saudi Arabia,
Taiwan, the United States, and Vietnam
441075-001
●
For use in Aruba, Austria, Azerbaijan, Bahrain, Belgium, Bermuda, Brazil, Bulgaria, the
Cayman Islands, Colombia, Croatia, Cyprus, the Czech Republic, Denmark, Egypt, El
Salvador, Estonia, Finland, France, Georgia, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Jordan, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, Montenegro, the Netherlands, Norway, Oman, the Philippines, Poland,
Portugal, Romania, Russia, Serbia, Singapore, Slovakia, Slovenia, South Africa, Spain,
Sri Lanka, Sweden, Switzerland, Turkey, the United Kingdom, and Uzbekistan
441075-002
●
For use in Ecuador, Haiti, Honduras, Pakistan, the People's Republic of China, Peru,
Qatar, South Korea, Uruguay, and Venezuela
441075-291
Intel 802.11a/b/g WLAN modules:
●
For use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India,
Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan,
Uruguay, the United States, Venezuela, and Vietnam
451861-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the
Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania,
Luxembourg, Malta, Monaco, Montenegro, the Netherlands, Norway, Oman, the
Philippines, Poland, Portugal, Qatar, Romania, Russia, Serbia, Singapore, Slovakia,
Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the
United Kingdom, and Uzbekistan
451861-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South
Korea
451861-003
●
For use in Japan
451861-291
Broadcom 802.11b/g WLAN modules:
Computer major components
Downloaded from LpManual.com Manuals
17
Item
Description
Spare part number
●
For use in Antigua and Barbuda, Argentina, Australia, the Bahamas, Barbados, Brunei,
Canada, Chile, the Dominican Republic, Guam, Guatemala, Hong Kong, India,
Indonesia, Malaysia, Mexico, New Zealand, Panama, Paraguay, Saudi Arabia,
Taiwan, the United States, and Vietnam
441090-001
●
For use in Aruba, Austria, Azerbaijan, Bahrain, Belgium, Bermuda, Brazil, Bulgaria, the
Cayman Islands, Colombia, Croatia, Cyprus, the Czech Republic, Denmark, Egypt, El
Salvador, Estonia, Finland, France, Georgia, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Jordan, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, Montenegro, the Netherlands, Norway, Oman, the Philippines, Poland,
Portugal, Romania, Russia, Serbia, Singapore, Slovakia, Slovenia, South Africa, Spain,
Sri Lanka, Sweden, Switzerland, Turkey, the United Kingdom, and Uzbekistan
441090-002
●
For use in Ecuador, Haiti, Honduras, Pakistan, the People's Republic of China, Peru,
Qatar, South Korea, Uruguay, and Venezuela
441090-291
Broadcom 802.11b/g WLAN module for use in Thailand
451861-004
Atheros AR2425 802.11b/g WLAN module:
●
(19)
(20)
18
For use in Albania, Algeria, Andorra, Angola, Antigua & Barbuda, Afghanistan, Syria,
Nether Antilles, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia &
Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia,
Cameroon, Cape Verde, Central African Republic, Chad, Chile, Colombia, Comoros,
Congo, Costa Rica, Croatia, Cyprus, Czech Republic, Zaire, Denmark, Djibouti,
Dominica, Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial
Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, Gabon, Gambia, Georgia,
Germany, Ghana, Gibraltar, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau,
Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland,
Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, South
Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Martinique, Guadeloupe,
Bermuda, French Guiana, Aruba, British Virgin Islands, Liechtenstein, Lithuania,
Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta,
Marshall Islands, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia,
Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, Netherlands, New
Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua, New Guinea, Paraguay, People's Republic of China, Peru, Philippines, Poland,
Portugal, Qatar, Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome & Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Korea,
Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga,
Trinidad & Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, United
Arab Emirates, United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zambia, Zimbabwe
459339-002
Memory modules
1024-MB (PC2-5300, 667-MHz, DDR2)
454922-001
512-MB (PC2-5300, 667-MHz, DDR2)
454921-001
256-MB (PC2-5300, 667-MHz, DDR2)
454920-001
Hard drives (includes bracket)
160-GB, 5400-rpm
454925-001
120-GB, 5400-rpm
454924-001
80-GB, 5400-rpm
454923-001
Hard Drive Kit (not illustrated, includes hard drive bracket and screws)
454926-001
Chapter 3 Illustrated parts catalog
Downloaded from LpManual.com Manuals
Item
Description
(21)
Optical drives (include bezel and bracket)
Spare part number
DVD±RW and CD-RW Super Multi, Double-Layer Combo Drive with LightScribe
454929-001
DVD±RW and CD-RW Super Multi, Double-Layer Combo Drive
454928-001
DVD/CD-RW Combo Drive
454927-001
Optical Drive Kit (not illustrated, includes bezel, bracket, and screws)
454930-001
Computer major components
Downloaded from LpManual.com Manuals
19
Display assembly components
Item
Description
(1)
Display bezels
Spare part number
For use only with HP G7000 computer models:
●
Without a camera
454909-001
●
With a camera
462445-001
For use only with Compaq Presario C700 computer models
●
Without a camera
454910-001
●
With a camera
462446-001
(2)
Camera module
462448-001
(3)
Display inverter (includes Mylar shield)
454915-001
(4)
15.4-inch, WSXGA + BrightView display panel (includes display panel cable)
454323-001
(5)
Display Hinge Kit (includes left and right display hinges)
454916-001
(6)
Wireless Antenna Kit (includes 2 wireless antenna transceivers and cables)
454919-001
(7)
Display Cable Kit (includes microphone)
454919-001
(8)
Display enclosures (include 2 wireless antenna transceivers and cables)
For use only with HP G7000 computer models:
20
Chapter 3 Illustrated parts catalog
Downloaded from LpManual.com Manuals
Item
Description
Spare part number
●
Without a camera
454911-001
●
With a camera
462443-001
For use only with Compaq Presario C700 computer models:
(9)
*
●
Without a camera
454913-001
●
With a camera
462444-001
Camera module cable
462447-001
Display Rubber Kit (not illustrated; includes rubber screw covers)
454917-001
Display Screw Kit (not illustrated)
454918-001
LCD logo kit
462457-001
*Not illustrated
Display assembly components
Downloaded from LpManual.com Manuals
21
Plastics Kit
Item
22
Description
Spare part number
Plastics Kit
454937-001
(1)
Memory/wireless module compartment cover (includes 2 captive screws, secured by C-clips)
(2)
Hard drive bay cover (includes 2 captive screws, secured by C-clips)
Chapter 3 Illustrated parts catalog
Downloaded from LpManual.com Manuals
Mass storage devices
Item
Description
(1)
Hard drives (include bracket)
(2)
Spare part number
160-GB, 5400-rpm
454925-001
120-GB, 5400-rpm
454924-001
80-GB, 5400-rpm
454923-001
Hard Drive Kit (not illustrated, includes hard drive bracket and screws)
454926-001
Optical drives (include bezel and bracket)
DVD±RW and CD-RW Super Multi, Double-Layer Combo Drive with LightScribe
454929-001
DVD±RW and CD-RW Super Multi, Double-Layer Combo Drive
454928-001
DVD/CD-RW Combo Drive
454927-001
Optical Drive Kit (not illustrated, includes bezel, bracket, and screws)
454930-001
Mass storage devices
Downloaded from LpManual.com Manuals
23
Miscellaneous parts
Description
Spare part number
65-W PFC AC adapter
457685-001
ATSC/NTSC/PAL TV tuner
439130-001
ATSC/NTSC TV tuner antenna
439131-001
Composite audio and S-Video cable
407939-001
DVB-T tuner
412175-001
DVB-T antenna adapter
412176-001
Earbud headset
371693-003
HP backpack
405527-001
HP carrying case
418162-001
HP Remote Control
407313-001
Infrared emitter with cable
439129-001
Optical wired mouse
436238-001
RF input adapter cable (without ferrite)
407940-001
Windows Vista remote control (fits inside ExpressCard slot)
439128-001
Windows Vista remote control (does not fit inside ExpressCard slot)
439254-001
Wireless laser mouse (includes cable adapter)
430958-001
Power cords:
24
Argentina
403811-D01
Australia and New Zealand
403811-011
Brazil
403811-201
Canada, French Canada, Latin America, Thailand, and the United States
403811-001
Denmark
403811-081
India
403811-D61
Israel
403811-BB1
Italy
403811-061
Japan
403811-291
The Netherlands and Europe
403811-B31
The People's Republic of China
403811-AA1
South Africa
403811-AR1
South Korea
403811-AD1
Switzerland
403811-111
Taiwan
403811-AB1
Chapter 3 Illustrated parts catalog
Downloaded from LpManual.com Manuals
Description
Spare part number
Hong Kong and the United Kingdom
403811-031
Screw Kit
454951-001
●
Phillips PM3.0×3.0 screw
●
Phillips PM2.5×9.0 screw
●
Phillips PM2.5×7.0 screw
●
Phillips PM2.5×6.0 captive screw
●
Phillips PM2.5×4.0 screw
●
Phillips PM2.0×5.0 captive screw
●
Black Phillips PM2.0×4.0 screw
●
Silver Phillips PM2.0×4.0 screw
Miscellaneous parts
Downloaded from LpManual.com Manuals
25
Sequential part number listing
26
Spare part
number
Description
371693-003
Earbud headset
403811-001
Power cord for use in Canada, French Canada, Latin America, Thailand, and the United States
403811-011
Power cord for use in Australia and New Zealand
403811-031
Power cord for use in Hong Kong and the United Kingdom
403811-061
Power cord for use in Italy
403811-081
Power cord for use in Denmark
403811-111
Power cord for use in Switzerland
403811-201
Power cord for use in Brazil
403811-291
Power cord for use in Japan
403811-AA1
Power cord for use in the People's Republic of China
403811-AB1
Power cord for use in Taiwan
403811-AD1
Power cord for use in South Korea
403811-AR1
Power cord for use in South Africa
403811-B31
Power cord for use in the Netherlands
403811-BB1
Power cord for use in Israel
403811-D01
Power cord for use in Argentina
403811-D61
Power cord for use in India
405527-001
HP backpack
407313-001
HP Remote Control
407939-001
Composite audio and S-Video cable
407940-001
RF input adapter cable (without ferrite)
412175-001
DVB-T tuner
412176-001
DVB-T antenna adapter
418162-001
HP carrying case
430958-001
Wireless laser mouse (includes cable adapter)
436238-001
Optical wired mouse
439128-001
Windows Vista remote control (fits inside ExpressCard slot)
439129-001
Infrared emitter with cable
439130-001
ATSC/NTSC/PAL TV tuner
439131-001
ATSC/NTSC TV tuner antenna
439254-001
Windows Vista remote control (does not fit inside ExpressCard slot)
Chapter 3 Illustrated parts catalog
Downloaded from LpManual.com Manuals
Spare part
number
Description
441075-001
Broadcom 802.11a/b/g WLAN module for use in Antigua and Barbuda, Argentina, Australia, the Bahamas,
Barbados, Brunei, Canada, Chile, the Dominican Republic, Guam, Guatemala, Hong Kong, India, Indonesia,
Malaysia, Mexico, New Zealand, Panama, Paraguay, Saudi Arabia, Taiwan, the United States, and Vietnam
441075-002
Broadcom 802.11a/b/g WLAN module for use in Aruba, Austria, Azerbaijan, Bahrain, Belgium, Bermuda,
Brazil, Bulgaria, the Cayman Islands, Colombia, Croatia, Cyprus, the Czech Republic, Denmark, Egypt, El
Salvador, Estonia, Finland, France, Georgia, Germany, Greece, Hungary, Iceland, Ireland, Italy, Jordan, Latvia,
Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, Montenegro, the Netherlands, Norway, Oman,
the Philippines, Poland, Portugal, Romania, Russia, Serbia, Singapore, Slovakia, Slovenia, South Africa, Spain,
Sri Lanka, Sweden, Switzerland, Turkey, the United Kingdom, and Uzbekistan
441075-291
Broadcom 802.11a/b/g WLAN module for use in Japan
441090-001
Broadcom 802.11b/g WLAN module for use in Antigua and Barbuda, Argentina, Australia, the Bahamas,
Barbados, Brunei, Canada, Chile, the Dominican Republic, Guam, Guatemala, Hong Kong, India, Indonesia,
Malaysia, Mexico, New Zealand, Panama, Paraguay, Saudi Arabia, Taiwan, the United States, and Vietnam
441090-002
Broadcom 802.11b/g WLAN module for use in Aruba, Austria, Azerbaijan, Bahrain, Belgium, Bermuda, Brazil,
Bulgaria, the Cayman Islands, Colombia, Croatia, Cyprus, the Czech Republic, Denmark, Egypt, El Salvador,
Estonia, Finland, France, Georgia, Germany, Greece, Hungary, Iceland, Ireland, Italy, Jordan, Latvia, Lebanon,
Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, Montenegro, the Netherlands, Norway, Oman, the
Philippines, Poland, Portugal, Romania, Russia, Serbia, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri
Lanka, Sweden, Switzerland, Turkey, the United Kingdom, and Uzbekistan
441090-291
Broadcom 802.11b/g WLAN module for use in Japan
448149-001
Intel Core 2 Duo T7100 1.80-GHz processor (2 MB of L2 cache, 800-MHz FSB)
451597-001
Intel Core Duo T5450 1.67-GHz processor (2 MB of L2 cache, 667-MHz FSB)
451861-001
Intel 802.11a/b/g WLAN module for use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados,
Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador,
El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico, Panama,
Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States, Venezuela, and Vietnam
451861-002
Intel 802.11a/b/g WLAN module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco,
Montenegro, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia,
Serbia, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine,
the United Kingdom, and Uzbekistan
451861-003
Intel 802.11a/b/g WLAN module for use in Australia, New Zealand, Pakistan, the People's Republic of China,
and South Korea
451861-004
Intel 802.11a/b/g WLAN module for use in Thailand
451861-291
Intel 802.11a/b/g WLAN module for use in Japan
453494-001
System board for use only with computer models without a Web camera equipped with Intel Core 2 Duo and
Core Duo processors and a card reader board
453495-001
System board for use only with computer models without a Web camera equipped with Intel Core 2 Duo and
Core Duo processors, but not a card reader board
454320-001
Intel Core 2 Duo T7250 2.00-GHz processor (2 MB of L2 cache, 800-MHz FSB)
454321-001
Intel Celeron M 540 1.86-GHz processor (1 MB of L2 cache, 533-MHz FSB)
454322-001
Intel Celeron M 550 2.00-GHz processor (1 MB of L2 cache, 533-MHz FSB)
454323-001
15.4-inch, WSXGA + BrightView display panel (includes display panel cable)
Sequential part number listing
Downloaded from LpManual.com Manuals
27
28
Spare part
number
Description
454882-001
System board for use only with computer models without a camera module equipped with Intel Celeron M
processors and a card reader board
454883-001
System board for use only with computer models without a Web camera equipped with Intel Celeron M
processors, but not a card reader board
454909-001
Display bezel for use only with HP G7000 computer models without a Web camera
454910-001
Display bezel for use only with Compaq Presario C700 computer models without a camera
454911-001
Display enclosure for use only with HP G7000 computer models without a camera (includes 2 WLAN antenna
transceivers and cables and microphone)
454913-001
Display enclosure for use only with Compaq Presario C700 computer models without a camera (includes 2
WLAN antenna transceivers and cables and microphone)
454915-001
Display inverter (includes Mylar shield)
454916-001
Display hinges
454917-001
Display Rubber Kit
454918-001
Display Screw Kit
454919-001
Display Cable Kit
454920-001
256-MB memory module (PC2-5300, 667-MHz, DDR2)
454921-001
512-MB memory module (PC2-5300, 667-MHz, DDR2)
454922-001
1024-MB memory module (PC2-5300, 667-MHz, DDR2)
454923-001
80-GB, 5400-rpm hard drive (includes bracket)
454924-001
120-GB, 5400-rpm hard drive (includes bracket)
454925-001
160-GB, 5400-rpm hard drive (includes bracket)
454926-001
Hard Drive Kit (includes hard drive bracket and screws)
454927-001
DVD/CD-RW Combo Drive
454928-001
DVD±RW and CD-RW Super Multi, Double-Layer Combo Drive
454929-001
DVD±RW and CD-RW Super Multi, Double-Layer Combo Drive with LightScribe
454930-001
Optical Drive Kit (includes bezel, bracket, and screws)
454931-001
6-cell, 2.2-Ah, 47-Wh battery
454932-001
15.4-inch, WSXGA + BrightView display assembly without a camera for use only with HP G7000 computer
models
454934-001
15.4-inch, WSXGA + BrightView display assembly without a camera for use only with Compaq Presario C700
computer models
454936-001
Top cover for use only with computer models not equipped with a Web camera (includes TouchPad and
cable)
454937-001
Plastics Kit (see Plastics Kit on page 22 for more information)
454938-001
Base enclosure for use only with computer models equipped with a card reader board
454939-001
Base enclosure for use only with computer models not equipped with a card reader board
Chapter 3 Illustrated parts catalog
Downloaded from LpManual.com Manuals
Spare part
number
Description
454940-001
Switch cover (includes power button board and cable, wireless button board and cable, and numeric lock LED
board and cable)
454941-001
USB board (includes cable)
454943-001
Heat sink (includes replacement thermal material)
454944-001
Fan
454945-001
Power connector cable
454946-001
Speakers
454947-001
RTC battery
454948-001
Caps lock LED board (includes cable)
454949-001
Card reader board
454950-001
Modem cable
454951-001
Screw Kit
454952-001
Rubber Foot Kit
454954-001
Keyboard for use in the United States
454954-031
Keyboard for use in the United Kingdom
454954-041
Keyboard for use in Germany
454954-051
Keyboard for use in France
454954-061
Keyboard for use in Italy
454954-071
Keyboard for use in Spain
454954-121
Keyboard for use in French Canada
454954-131
Keyboard for use in Portugal
454954-141
Keyboard for use in Turkey
454954-151
Keyboard for use in Greece
454954-161
Keyboard for use in Latin America
454954-171
Keyboard for use in Saudi Arabia
454954-201
Keyboard for use in Brazil
454954-221
Keyboard for use in Czechoslovakia
454954-251
Keyboard for use in Russia
454954-281
Keyboard for use in Thailand
454954-291
Keyboard for use in Japan
454954-A41
Keyboard for use in Belgium
454954-AB1
Keyboard for use in Taiwan
454954-AD1
Keyboard for use in South Korea
454954-B31
Keyboard for use in the Netherlands
Sequential part number listing
Downloaded from LpManual.com Manuals
29
30
Spare part
number
Description
454954-BB1
Keyboard for use in Israel
454954-BG1
Keyboard for use in Switzerland
454954-DH1
Keyboard for use in Denmark, Finland, Norway, and Sweden
455437-001
Intel Celeron M 530 1.73-GHz processor (1 MB of L2 cache, 533-MHz FSB)
455943-001
Intel Core Duo T2310 1.46-GHz processor (1 MB of L2 cache, 667-MHz FSB)
455944-001
Intel Core Duo T2330 1.60-GHz processor (1 MB of L2 cache, 667-MHz FSB)
457685-001
65-W AC adapter
459797-001
Intel Core Duo T8100 2.10-GHz processor, 3-MB L2 cache; includes thermal material
459798-001
Intel Core Duo T8300 2.40-GHz processor, 3-MB L2 cache; includes thermal material
459339-001
Atheros AR2425 802.11b/g WLAN module for use in Albania, Algeria, Andorra, Angola, Antigua & Barbuda,
Afghanistan, Syria, Nether Antilles, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia & Herzegovina, Botswana,
Brazil, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, Central African Republic,
Chad, Chile, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, Czech Republic, Zaire, Denmark,
Djibouti, Dominica, Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea,
Estonia, Ethiopia, Fiji, Finland, France, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece,
Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India,
Indonesia, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, South Kuwait,
Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Martinique, Guadeloupe, Bermuda, French Guiana, Aruba,
British Virgin Islands, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
Maldives, Mali, Malta, Marshall Islands, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia,
Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Niger,
Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua, New Guinea, Paraguay, People's Republic of
China, Peru, Philippines, Poland, Portugal, Qatar, Republic of Moldova, Romania, Russia, Rwanda, Samoa, San
Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore, Slovakia,
Slovenia, Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia,
St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania,
Thailand, Togo, Tonga, Trinidad & Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, United
Arab Emirates, United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zambia,
Zimbabwe
462353-001
Intel Dual Core T5750 2.00-GHz processor, 2-MB L2 cache; includes thermal material
462354-001
Intel Core Duo T2370 1.73-GHz processor (1 MB of L2 cache, 667-MHz FSB)
462439-001
System board for use only with computer models with a Web camera equipped with Intel Core 2 Duo and Core
Duo processors and a card reader board
462440-001
System board for use only with computer models with a Web camera equipped with Intel Core 2 Duo and Core
Duo processors, but not a card reader board
462441-001
System board for use only with computer models with a Web camera equipped with Intel Celeron M processors
and a card reader board
462442-001
System board for use only with computer models with a Web camera equipped with Intel Celeron M processors,
but not a card reader board
462443-001
Display enclosure for use only with HP G7000 computer models with a Web camera (includes 2 WLAN antenna
transceivers and cables and microphone)
462444-001
Display enclosure for use only with Compaq Presario C700 computer models with a Web camera (includes 2
WLAN antenna transceivers and cables and microphone)
462445-001
Display bezel for use only with HP G7000 computer models with a Web camera
Chapter 3 Illustrated parts catalog
Downloaded from LpManual.com Manuals
Spare part
number
Description
462446-001
Display bezel for use only with Compaq Presario C700 computer models with a Web camera
462447-001
Camera cable
462448-001
Camera module
462455-001
15.4-inch, WSXGA + BrightView display assembly with a Web camera for use only with HP G7000 computer
models
462456-001
15.4-inch, WSXGA + BrightView display assembly with a Web camera for use only with Compaq Presario
C700 computer models
462457-001
LCD logo kit
466649-001
Top cover for use only with computer models equipped with a Web camera (includes TouchPad and cable)
Sequential part number listing
Downloaded from LpManual.com Manuals
31
4
Removal and replacement
procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
Flat-bladed screwdriver
●
Magnetic screwdriver
●
Phillips P0 and P1 screwdrivers
Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly
and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
Using excessive force during disassembly and reassembly can damage plastic parts. Use care when
handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.
32
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat
or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In
all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that
they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme
care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer
is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and be
sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
Preliminary replacement requirements
Downloaded from LpManual.com Manuals
33
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some protection,
but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you area ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described in
this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different
activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
34
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●
Place items on a grounded surface before removing items from their containers.
●
Always be properly grounded when touching a component or assembly.
●
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
●
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized
equipment used for moving materials is wired to ground and that proper materials are selected to
avoid static charging. When grounding is not possible, use an ionizer to dissipate electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
●
Cover the workstation with approved static-shielding material.
●
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.
●
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
●
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
●
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these
items only at static-free workstations.
●
Avoid contact with pins, leads, or circuitry.
●
Turn off power and input signals before inserting or removing connectors or test equipment.
Preliminary replacement requirements
Downloaded from LpManual.com Manuals
35
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground,
wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors,
use alligator clips to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can
be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm
resistance between the operator and ground. To be effective, the conductive strips must be worn in
contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
Antistatic tape
●
Antistatic smocks, aprons, and sleeve protectors
●
Conductive bins and other assembly or soldering aids
●
Nonconductive foam
●
Conductive tabletop workstations with ground cords of one megohm resistance
●
Static-dissipative tables or floor mats with hard ties to the ground
●
Field service kits
●
Static awareness labels
●
Material-handling packages
●
Nonconductive plastic bags, tubes, or boxes
●
Metal tote boxes
●
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
36
Material
Use
Voltage protection level
Antistatic plastic
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Unknown user password
If the computer you are servicing has an unknown user password, follow these steps to clear the password.
NOTE:
These steps also clear CMOS.
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the RTC battery (see RTC battery on page 75).
6.
Wait approximately 5 minutes.
7.
Replace the RTC battery and reassemble the computer.
8.
Connect AC power to the computer. Do not reinsert any batteries at this time.
9.
Turn on the computer.
All passwords and all CMOS settings have been cleared.
Preliminary replacement requirements
Downloaded from LpManual.com Manuals
37
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 79 screws, in 9 different sizes, that must be removed, replaced, or loosened when
servicing the computer. Make special note of each screw size and location during removal and
replacement.
Serial number
Report the computer serial number to HP when requesting information or ordering spare parts. The serial
number is located on the bottom of the computer.
38
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Computer feet
Description
Spare part number
Rubber Foot Kit (includes 6 base enclosure rubber feet)
454952-001
The computer feet are adhesive-backed rubber pads. The feet attach to the base enclosure in the locations
illustrated below.
Component replacement procedures
Downloaded from LpManual.com Manuals
39
Battery
Description
Spare part number
6-cell, 2.20-Ah, 47-Wh Li-ion battery
454931-001
Before disassembling the computer, follow these steps
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the battery:
1.
Turn the computer upside down on a flat surface.
2.
Slide the battery release latch (1) to release the battery.
3.
Pivot the battery (2) upward and remove it from the computer (3).
To insert the battery, insert the rear edge of the battery into the battery bay and pivot the front edge
downward until the battery is seated. The battery release latch automatically locks the battery into place.
40
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Hard drive
NOTE:
All hard drive spare part kits include a hard drive bracket.
Description
Spare part number
160-GB, 5400-rpm
454925-001
120-GB, 5400-rpm
454924-001
80-GB, 5400-rpm
454923-001
Before removing the hard drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
Remove the hard drive:
1.
Position the computer with the front toward you.
2.
Loosen the two Phillips PM2.0×5.0 captive screws (1) that secure the hard drive bay cover to the
computer.
3.
Lift the left side of the hard drive bay cover (2), swing it up and to the right, and remove the cover.
The hard drive bay cover is included in the Plastics Kit, spare part number 454937-001.
4.
Use the Mylar tab (1) to slide the hard drive (2) to the left until it disconnects from the system board.
Component replacement procedures
Downloaded from LpManual.com Manuals
41
5.
Remove the hard drive (3) from the hard drive bay.
6.
Remove the hard drive from the hard drive bay.
7.
If it is necessary to replace the hard drive bracket, remove the four Phillips PM3.0×3.0 screws (1)
that secure the hard drive bracket to the hard drive.
8.
Lift the bracket (2) straight up to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.
42
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Memory module
Description
Spare part number
1024-MB (667-MHz, PC2-5300, DDR2)
454922-001
512-MB (667-MHz, PC2-5300, DDR2)
454920-001
256-MB (667-MHz, PC2-5300, DDR2)
454921-001
Before removing the memory module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
Remove the memory module:
1.
Loosen the two Phillips PM2.0×5.0 captive screws (1) that secure the memory/wireless module
compartment cover to the computer.
2.
Lift the rear edge of the cover (2), swing it up and forward, and remove the cover. The memory/
wireless module compartment cover is included in the Plastics Kit, spare part number
454937-001.
3.
Spread the retaining tabs (1) on each side of the memory module slot to release the memory module.
(The edge of the module opposite the slot rises away from the computer.)
Component replacement procedures
Downloaded from LpManual.com Manuals
43
4.
Remove the module (2) by pulling it away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect installation into the
memory module slot.
Reverse this procedure to install a memory module.
44
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
WLAN module
Description
Spare part number
Broadcom 802.11a/b/g WLAN modules:
●
For use in Antigua and Barbuda, Argentina, Australia, the Bahamas, Barbados, Brunei, Canada,
Chile, the Dominican Republic, Guam, Guatemala, Hong Kong, India, Indonesia, Malaysia,
Mexico, New Zealand, Panama, Paraguay, Saudi Arabia, Taiwan, the United States, and
Vietnam
441075-001
●
For use in Aruba, Austria, Azerbaijan, Bahrain, Belgium, Bermuda, Brazil, Bulgaria, the Cayman
Islands, Colombia, Croatia, Cyprus, the Czech Republic, Denmark, Egypt, El Salvador, Estonia,
Finland, France, Georgia, Germany, Greece, Hungary, Iceland, Ireland, Italy, Jordan, Latvia,
Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, Montenegro, the Netherlands,
Norway, Oman, the Philippines, Poland, Portugal, Romania, Russia, Serbia, Singapore,
Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, the United
Kingdom, and Uzbekistan
441075-002
●
For use in Japan
441075-291
Intel 802.11a/b/g WLAN modules:
●
For use in Antigua and Barbuda, Argentina, Australia, the Bahamas, Barbados, Brunei, Canada,
Chile, the Dominican Republic, Guam, Guatemala, Hong Kong, India, Indonesia, Malaysia,
Mexico, New Zealand, Panama, Paraguay, Saudi Arabia, Taiwan, the United States, and
Vietnam
451861-001
●
For use in Aruba, Austria, Azerbaijan, Bahrain, Belgium, Bermuda, Brazil, Bulgaria, the Cayman
Islands, Colombia, Croatia, Cyprus, the Czech Republic, Denmark, Egypt, El Salvador, Estonia,
Finland, France, Georgia, Germany, Greece, Hungary, Iceland, Ireland, Italy, Jordan, Latvia,
Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, Montenegro, the Netherlands,
Norway, Oman, the Philippines, Poland, Portugal, Romania, Russia, Serbia, Singapore,
Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, the United
Kingdom, and Uzbekistan
451861-002
●
For use in Ecuador, Haiti, Honduras, Pakistan, the People's Republic of China, Peru, Qatar, South
Korea, Uruguay, and Venezuela
451861-003
●
For use in Japan
451861-291
Broadcom 802.11b/g WLAN modules:
●
For use in Antigua and Barbuda, Argentina, Australia, the Bahamas, Barbados, Brunei, Canada,
Chile, the Dominican Republic, Guam, Guatemala, Hong Kong, India, Indonesia, Malaysia,
Mexico, New Zealand, Panama, Paraguay, Saudi Arabia, Taiwan, the United States, and
Vietnam
441090-001
●
For use in Aruba, Austria, Azerbaijan, Bahrain, Belgium, Bermuda, Brazil, Bulgaria, the Cayman
Islands, Colombia, Croatia, Cyprus, the Czech Republic, Denmark, Egypt, El Salvador, Estonia,
Finland, France, Georgia, Germany, Greece, Hungary, Iceland, Ireland, Italy, Jordan, Latvia,
Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, Montenegro, the Netherlands,
Norway, Oman, the Philippines, Poland, Portugal, Romania, Russia, Serbia, Singapore,
Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, the United
Kingdom, and Uzbekistan
441090-002
●
For use in Japan
441090-291
802.11b/g WLAN module for use in Thailand
451861-004
Atheros AR2425 802.11b/g WLAN module:
●
For use in Albania, Algeria, Andorra, Angola, Antigua & Barbuda, Afghanistan, Syria, Nether
Antilles, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia & Herzegovina, Botswana,
Brazil, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, Central
459339-002
Component replacement procedures
Downloaded from LpManual.com Manuals
45
Description
Spare part number
African Republic, Chad, Chile, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, Czech
Republic, Zaire, Denmark, Djibouti, Dominica, Dominican Republic, East Timor, Ecuador, Egypt,
El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, Gabon, Gambia,
Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau,
Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy,
Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, South Kuwait, Kyrgyzstan,
Laos, Latvia, Lebanon, Lesotho, Liberia, Martinique, Guadeloupe, Bermuda, French Guiana,
Aruba, British Virgin Islands, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar,
Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan,
Palau, Panama, Papua, New Guinea, Paraguay, People's Republic of China, Peru, Philippines,
Poland, Portugal, Qatar, Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome & Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St.
Kitts & Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad & Tobago, Tunisia,
Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, United Arab Emirates, United Kingdom,
Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zambia, Zimbabwe
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module
authorized for use in the computer by the governmental agency that regulates wireless devices in your
country or region. If you replace the module and then receive a warning message, remove the module to
restore computer functionality, and then contact technical support through Help and Support.
Before removing the WLAN module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the hard drive bay cover (see Hard drive on page 41).
Remove the WLAN module:
1.
Position the computer with the front toward you.
2.
Disconnect the two WLAN antenna cables (1) from the WLAN module.
NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The
white WLAN antenna cable is connected to the WLAN module “Aux” terminal.
3.
46
Remove the two Phillips PM2.0×4.0 screws (2) that secure the WLAN module to the computer. (The
edge of the module opposite the slot rises away from the computer.)
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
4.
Remove the WLAN module (3) by pulling it away from the slot at an angle.
NOTE: WLAN modules are designed with a notch (4) to prevent incorrect installation into the
WLAN module slot.
Reverse this procedure to install a WLAN module.
Component replacement procedures
Downloaded from LpManual.com Manuals
47
Optical drive
NOTE: All optical drive spare part kits include an optical drive bezel.
Description
Spare part number
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
454929-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
454928-001
DVD/CD-RW Combo Drive
454927-001
Before removing the optical drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
Remove the optical drive:
48
1.
Position the computer with right side toward you.
2.
Remove the Phillips PM2.5×9.0 screw (1) that secures the optical drive to the computer.
3.
Insert a thin tool, such as a paper clip (2), into the release access. (The optical drive media tray is
partially ejected from the optical drive.)
4.
Use the media tray frame to remove the optical drive (3).
5.
If it is necessary to replace the optical drive bracket, position the optical drive with the optical drive
bracket toward you.
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
6.
Remove the two Phillips PM2.0×3.0 screws (1) that secure the optical drive bracket to the optical
drive.
7.
Remove the optical drive bracket (2).
Reverse the above procedure to reassemble and install the optical drive.
Component replacement procedures
Downloaded from LpManual.com Manuals
49
Keyboard
For use in:
Spare part number
For use in:
Spare part number
Belgium
454954-A41
The Netherlands and Europe
454954-B31
Brazil
454954-201
Portugal
454954-131
Czechoslovakia
454954-221
Russia
454954-251
Denmark, Finland, Norway, and
Sweden
454954-DH1
Saudi Arabia
454954-171
France
454954-051
South Korea
454954-AD1
French Canada
454954-121
Spain
454954-071
Germany
454954-041
Switzerland
454954-BG1
Greece
454954-151
Taiwan
454954-AB1
Israel
454954-BB1
Thailand
454954-281
Italy
454954-061
Turkey
454954-141
Japan
454954-291
The United Kingdom
454954-031
Latin America
454954-161
The United States
454954-001
Before removing the keyboard, follow these steps:
50
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Remove the keyboard:
1.
Remove the three Phillips PM2.5×9.0 screws that secure the keyboard to the computer.
2.
Turn the computer right-side up, with the front toward you.
3.
Open the computer as far as possible.
4.
Lift the rear edge of the keyboard (1) until it rests at an angle.
5.
Release the keyboard (2) by sliding it back until it rests on the display assembly.
Component replacement procedures
Downloaded from LpManual.com Manuals
51
6.
Release the zero insertion force (ZIF) connector to which the keyboard cable (1) is attached and
disconnect the cable (2) from the system board.
7.
Remove the keyboard.
Reverse this procedure to install the keyboard.
52
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Switch cover
Description
Spare part number
Switch cover (includes caps lock LED board and cable, power button board and cable, and wireless
button board and cable)
454940-001
Before removing the switch cover, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the keyboard (see Keyboard on page 50).
Remove the switch cover:
1.
Turn the computer upside down, with the rear panel toward you.
2.
Remove the four Phillips PM2.5×9.0 screws (1) and the four black Phillips PM2.5×4.0 screws (2)
that secure the switch cover to the computer.
3.
Turn the computer right-side up, with the front toward you.
4.
Open the computer as far as possible.
5.
Release the ZIF connector to which the power button board cable (1) is connected and disconnect
the cable from the system board.
Component replacement procedures
Downloaded from LpManual.com Manuals
53
6.
Remove the switch cover (2).
Reverse this procedure to install the switch cover.
54
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Display assembly
Description
Spare part number
For use only with HP G7000 computer models:
15.4-inch, WSXGA+BrightView display assembly without a camera
454932-001
15.4-inch, WSXGA+BrightView display assembly with a camera
462455-001
For use only with Compaq Presario C700 computer models:
15.4-inch, WSXGA+BrightView display assembly without a camera
454934-001
15.4-inch, WSXGA+BrightView display assembly with a camera
462456-001
Before removing the display assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Disconnect the wireless antenna cables from the WLAN module (see WLAN module on page 45).
6.
Remove the keyboard (see Keyboard on page 50).
7.
Remove the switch cover (see Switch cover on page 53).
Remove the display assembly:
1.
Disconnect the display panel cable (1) from the system board and remove the cable from the
clips (2) and routing channel built into the top cover.
2.
Disconnect the microphone cable (3) from the system board .
Component replacement procedures
Downloaded from LpManual.com Manuals
55
3.
Remove the microphone cable and the WLAN antenna cables from the clips (4) and routing channel
built into the top cover.
CAUTION: The display assembly will be unsupported when the following screws are removed. To
prevent damage to the display assembly, support it before removing the screws.
56
4.
Remove the four black Phillips PM2.5×9.0 screws (1) that secure the display assembly to the
computer.
5.
Remove the display assembly (2).
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
6.
If it is necessary to replace any of the display assembly internal components, remove the following
screw covers and screws. The display rubber screw covers are included in the Display Rubber Kit,
spare part number 454917-001.
(1) Six rubber screw covers on the display bezel top edge and bottom edge corners. The rubber
screw covers are available in the Display Rubber Kit, spare part number 454917-001.
NOTE: There are two different sizes of display bezel rubber screw covers. The thicker covers (2)
must be installed in the bottom center screw holes.
(2) Two rubber screw covers on the display bezel bottom edge.
(3) Eight Phillips PM2.5×7.0 screws.
7.
Flex the inside edges of the left and right sides (1) and the top and bottom sides (2) of the display
bezel until the bezel disengages from the display enclosure.
8.
Remove the display bezel (3). The display bezel is available using spare part numbers 454909-001
(HP G7000 computer models without a camera), 462445-001 (HP G7000 computer models with
a camera, 454910-001 (Compaq Presario C700 computer models without a camera), and
462446-001 (Compaq Presario C700 computer models with a camera).
Component replacement procedures
Downloaded from LpManual.com Manuals
57
9.
If it is necessary to replace the display inverter, release the inverter (1) as far as the display panel
cable and the backlight cable will allow.
10. Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter.
11. Remove the inverter. The display inverter is available using spare part number 454915-001.
12. If it is necessary to replace the display hinges, remove the four Phillips PM2.0×4.0 screws (1) that
secure each hinge to the display panel.
13. Remove the display hinges (2) from the display panel. The display hinges are available using spare
part number 454916-001.
14. If it is necessary to replace the display panel, remove the six Phillips PM2.5×4.0 screws (1) that
secure the panel to the display enclosure.
58
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
15. Remove the display panel (2) from the display enclosure. The display panel is available using the
spare part number 454323-001.
16. If it is necessary to replace the wireless antenna transceivers and cables, remove the two Phillips
PM2.5×4.0 screws (1) that secure the transceivers to the display enclosure.
17. Remove the wireless antenna cables from the clips (2) built into the display enclosure.
18. Detach the wireless antenna transceivers (3) from the display enclosure.
19. Remove the wireless antenna transceivers and cables (4) from the display enclosure. The wireless
antenna transceivers and cables are available in the Display Cable Kit, spare part number
454919-001.
20. If it is necessary to replace the microphone receiver and cable, release the retention tabs (1) built
into the display enclosure that secure the microphone cable to the display enclosure.
21. Remove the microphone receiver (2) from the clip in the display enclosure.
Component replacement procedures
Downloaded from LpManual.com Manuals
59
22. Remove the microphone cable (3) from the display enclosure. The microphone receiver and cable
are included in the Display Cable Kit, spare part number 454919-001.
Reverse this procedure to reassemble and install the display assembly.
Camera module
If it has been determined that the camera module is the component that must be replaced to complete the
computer repair, the display assembly does not have to be removed. Follow the procedures in this section
to replace the camera module. For information on replacing the display assembly and other display
assembly internal components, see Display assembly on page 55.
Description
Spare part number
Camera module
462448-001
Before removing the camera module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
Remove the camera module:
60
1.
Turn the computer display-side up, with the front toward you.
2.
Open the computer as far as it will open.
3.
Remove the four rubber screw covers (1) on the display bezel top edge. The display rubber screw
covers are included in the Display Rubber Kit, spare part number 454917-001.
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
4.
Remove the four Phillips PM2.5×7.0 screws (2) that secure the display bezel top edge to the display
assembly.
5.
Flex the inside edges of the left and right sides (1) and the top edge (2) of the display bezel until
the bezel disengages from the display enclosure.
6.
Release the display bezel top edge (3). Display bezels are available using the following spare part
numbers:
7.
●
454909-001 (for use only with HP G7000 computer models without a Web camera; includes
microphone; includes openings for camera module and microphones)
●
462445-001 (for use only with HP G7000 computer models with a Web camera; includes
openings for microphones)
●
454910-001 (for use only with Compaq Presario C700 computer models without a Web
camera; includes openings for microphones)
●
462446-001 (for use only with Compaq Presario C700 computer models with a Web camera;
includes openings for microphones)
Remove the screws (1), and then release the camera module (2) from the display enclosure as far
as the camera module cable allows.
Component replacement procedures
Downloaded from LpManual.com Manuals
61
8.
Disconnect the camera module cable (3) from the camera module.
Reverse this procedure to install the camera module.
Top cover
Description
Spare part number
Top cover for use only in computer models not equipped with a Web camera (includes TouchPad and
cable)
454936-001
Top cover for use only in computer models equipped with a Web camera (includes TouchPad and
cable)
466649-001
Before removing the top cover, follow these steps:
62
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 41)
b.
Optical drive (see Optical drive on page 48)
c.
Keyboard (see Keyboard on page 50)
d.
Switch cover (see Switch cover on page 53)
e.
Display assembly (see Display assembly on page 55)
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Remove the top cover:
1.
Turn the computer upside down, with the front toward you.
2.
Remove the two Phillips PM2.5×4.0 screws (1) and the ten Phillips PM2.5×9.0 screws (2) that secure
the top cover to the computer.
3.
Turn the computer right-side up, with the front toward you.
4.
Disconnect the caps lock LED board cable (1) from the system board.
5.
Release the ZIF connector to which the TouchPad cable is connected and disconnect the cable (2)
from on the system board.
6.
Lift the rear edge of the top cover (1) and swing it (2) up and forward until it rests at an angle.
Component replacement procedures
Downloaded from LpManual.com Manuals
63
7.
Remove the top cover (3).
Reverse this procedure to install the top cover.
Caps lock LED board
Description
Spare part number
Caps lock LED board (includes cable)
454948-001
Before removing the caps lock LED board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 41)
b.
Optical drive (see Optical drive on page 48)
c.
Keyboard (see Keyboard on page 50)
d.
Switch cover (see Switch cover on page 53)
e.
Display assembly (see Display assembly on page 55)
f.
Top cover (see Top cover on page 62)
Remove the caps lock LED board:
64
1.
Turn the top cover upside down, with the front toward you.
2.
Remove the Phillips PM2.0×4.0 screw (1) that secures the caps lock LED board to the top cover.
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
3.
Remove the caps lock LED board (2) from the top cover.
Reverse the above procedure to install the caps lock LED board.
Component replacement procedures
Downloaded from LpManual.com Manuals
65
USB board
Description
Spare part number
USB board (includes USB board cable)
454941-001
Before removing the USB board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 41)
b.
Optical drive (see Optical drive on page 48)
c.
Keyboard (see Keyboard on page 50)
d.
Switch cover (see Switch cover on page 53)
e.
Display assembly (see Display assembly on page 55)
f.
Top cover (see Top cover on page 62)
Remove the USB board:
66
1.
Disconnect the USB board cable (1) from the system board.
2.
Remove the Phillips PM2.5×4.0 screw (2) that secures the USB board to the base enclosure.
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
3.
Remove the USB board (3) from the base enclosure.
Reverse this procedure to install the USB board.
Component replacement procedures
Downloaded from LpManual.com Manuals
67
Fan
Description
Spare part number
Fan
454944-001
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left side of
the computer. The computer uses an electric fan for ventilation. The fan is controlled by a temperature
sensor and is designed to turn on automatically when high temperature conditions exist. These conditions
are affected by high external temperatures, system power consumption, power management/battery
conservation configurations, battery fast charging, and software requirements. Exhaust air is displaced
through the ventilation grill located on the left side of the computer.
Before removing the fan, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 41)
b.
Optical drive (see Optical drive on page 48)
c.
Keyboard (see Keyboard on page 50)
d.
Switch cover (see Switch cover on page 53)
e.
Display assembly (see Display assembly on page 55)
f.
Top cover (see Top cover on page 62)
Remove the fan:
68
1.
Disconnect the fan cable (1) from the system board.
2.
Remove the Phillips PM2.0×9.0 screw (2) that secures the fan to the base enclosure.
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
3.
Remove the fan (3).
Reverse this procedure to install the fan.
Component replacement procedures
Downloaded from LpManual.com Manuals
69
Speakers
Description
Spare part number
Speakers
454946-001
Before removing the speakers, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 41)
b.
Optical drive (see Optical drive on page 48)
c.
Keyboard (see Keyboard on page 50)
d.
Switch cover (see Switch cover on page 53)
e.
Display assembly (see Display assembly on page 55)
f.
Top cover (see Top cover on page 62)
Remove the speakers:
70
1.
Disconnect the speaker cable (1) from the system board.
2.
Remove the speaker cables (2) from the clip in the system board and the clips built into the base
enclosure.
3.
Remove the two Phillips PM2.5×4.0 screws (3) that secure the speakers to the base enclosure.
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
4.
Remove the speakers (4) from the base enclosure.
Reverse this procedure to install the speakers.
Component replacement procedures
Downloaded from LpManual.com Manuals
71
System board
NOTE: All system board spare part kits include replacement thermal material.
Description
Spare part number
For use in computer models not equipped with a Web camera:
●
For use only with computer models equipped with Intel Core 2 Duo and Core Duo processors
and a card reader board
453494-001
●
For use only with computer models equipped with Intel Core 2 Duo and Core Duo processors,
but not a card reader board
454882-001
●
For use only with computer models equipped with Intel Celeron M processors and a card reader
board
453495-001
●
For use only with computer models equipped with Intel Celeron M processors, but not a card
reader board
454883-001
For use in computer models equipped with a Web camera:
●
Equipped with Intel Core 2 Duo and Core Duo processors and a card reader board
462439-001
●
Equipped with Intel Core 2 Duo and Core Duo processors, but not a card reader board
462441-001
●
Equipped with Intel Celeron M processors and a card reader board
462440-001
●
Equipped with Intel Celeron M processors, but not a card reader board
462442-001
Before removing the system board, follow these steps:
72
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 41)
b.
Optical drive (see Optical drive on page 48)
c.
Keyboard (see Keyboard on page 50)
d.
Switch cover (see Switch cover on page 53)
e.
Display assembly (see Display assembly on page 55)
f.
Top cover (see Top cover on page 62)
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●
Memory modules (see Memory module on page 43)
●
WLAN module (see WLAN module on page 45)
●
RTC battery (see RTC battery on page 75)
●
Card reader board (see Card reader board on page 77)
●
Heat sink (see Heat sink on page 79)
●
Processor (see Processor on page 81)
●
Power connector cable (see Power connector cable on page 83)
Remove the system board:
1.
Remove the power connector (1) from the clip built into the base enclosure.
2.
Remove the power connector cable (2) from the routing channel and clips built into the base
enclosure.
3.
Remove the black Phillips PM2.5×4.0 screw (3) that secures the system board to the base enclosure.
4.
Disconnect the USB board cable (4) from the system board.
5.
Flex the front edge of the base enclosure (1) outward to provide clearance for the audio
connectors (2).
6.
Use the optical drive connector (3) to lift the right side of the system board (4) until it rests at an
angle.
Component replacement procedures
Downloaded from LpManual.com Manuals
73
7.
Remove the system board (5) by pulling it away from the base enclosure at an angle.
Reverse the preceding procedure to install the system board.
74
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
RTC battery
NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords
and CMOS settings to be cleared.
Description
Spare part number
RTC battery (includes double-sided tape)
454947-001
Before removing the RTC battery, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 41)
b.
Optical drive (see Optical drive on page 48)
c.
Keyboard (see Keyboard on page 50)
d.
Switch cover (see Switch cover on page 53)
e.
Display assembly (see Display assembly on page 55)
f.
Top cover (see Top cover on page 62)
g.
System board (see System board on page 72)
Remove the RTC battery:
1.
Turn the system board upside down, with the audio connectors toward you.
2.
Disconnect the RTC battery cable (1) from the system board.
Component replacement procedures
Downloaded from LpManual.com Manuals
75
3.
Remove the RTC battery (2).
NOTE: The RTC battery is attached to the system board with double-sided tape.
Reverse this procedure to install the RTC battery.
76
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Card reader board
Description
Spare part number
Card reader board
454949-001
Before removing the card reader board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 41)
b.
Optical drive (see Optical drive on page 48)
c.
Keyboard (see Keyboard on page 50)
d.
Switch cover (see Switch cover on page 53)
e.
Display assembly (see Display assembly on page 55)
f.
Top cover (see Top cover on page 62)
g.
System board (see System board on page 72)
Remove the card reader board:
1.
Turn the system board upside down, with the audio connectors toward you.
2.
Remove the three Phillips PM2.0×4.0 screws (1) that secure the card reader board to the system
board.
Component replacement procedures
Downloaded from LpManual.com Manuals
77
3.
Lift the card reader board (2) straight up to disconnect it from the system board.
4.
Remove the card reader board.
Reverse the above procedure to install the card reader board.
78
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Heat sink
Description
Spare part number
Heat sink (includes thermal material)
454943-001
Before removing the heat sink, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 41)
b.
Optical drive (see Optical drive on page 48)
c.
Keyboard (see Keyboard on page 50)
d.
Switch cover (see Switch cover on page 53)
e.
Display assembly (see Display assembly on page 55)
f.
Top cover (see Top cover on page 62)
g.
System board (see System board on page 72)
Remove the heat sink:
1.
Turn the system board upside down, with the audio connectors toward you.
2.
Loosen the four Phillips PM2.5×6.0 captive screws (1) that secure the heat sink to the system board.
NOTE: Due to the adhesive quality of the thermal material located between the heat sink and
system board components, it may be necessary to move the heat sink from side to side to detach the
assembly.
Component replacement procedures
Downloaded from LpManual.com Manuals
79
3.
Remove the heat sink (2).
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the system board (1)
and (2) and the heat sink (3) and (4) each time the heat sink is removed. Thermal pads and thermal
paste must be installed on all surfaces before the heat sink is reinstalled. Thermal pads and thermal paste
are included with all heat sink, system board, and processor spare part kits.
Reverse this procedure to install the heat sink.
80
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Processor
NOTE:
All processor spare part kits include replacement thermal material.
Description
Spare part number
Intel Core 2 Duo T8300 (2.40-GHz, 3 MB of L2 cache, 800-MHz FSB)
459798-001
Intel Core 2 Duo T8100 (2.10-GHz, 3 MB of L2 cache, 800-MHz FSB)
459797-001
Intel Core 2 Duo T7250 (2.00-GHz, 2 MB of L2 cache, 800-MHz FSB)
454320-001
Intel Core 2 Duo T7100 (1.80-GHz, 2 MB of L2 cache, 800-MHz FSB)
448149-001
Intel Core Duo T5750 (2.00-GHz, 2 MB of L2 cache, 667-MHz FSB)
462353-001
Intel Core Duo T5450 (1.67-GHz, 2 MB of L2 cache, 667-MHz FSB)
451597-001
Intel Core Duo T2370 (1.73-GHz, 1 MB of L2 cache, 667-MHz FSB)
462354-001
Intel Core Duo T2330 (1.50-GHz, 1 MB of L2 cache, 667-MHz FSB)
455944-001
Intel Core Duo T2310 (1.50-GHz, 1 MB of L2 cache, 667-MHz FSB)
455943-001
Intel Celeron M 550 (2.00-GHz, 1 MB of L2 cache, 533-MHz FSB)
454322-001
Intel Celeron M 540 (1.86-GHz, 1 MB of L2 cache, 533-MHz FSB)
454321-001
Intel Celeron M 530 (1.73-GHz, 1 MB of L2 cache, 533-MHz FSB)
455437-001
Before removing the processor, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 41)
b.
Optical drive (see Optical drive on page 48)
c.
Keyboard (see Keyboard on page 50)
d.
Switch cover (see Switch cover on page 53)
e.
Display assembly (see Display assembly on page 55)
f.
Top cover (see Top cover on page 62)
g.
System board (see System board on page 72)
Component replacement procedures
Downloaded from LpManual.com Manuals
81
Remove the processor:
1.
Turn the system board upside down, with the audio connectors toward you.
2.
Turn the processor locking screw (1) one-half turn counterclockwise until you hear a click.
3.
Lift the processor (2) straight up and remove it.
NOTE: When you install the processor, the gold triangle (3) on the processor must be aligned with
the triangle icon (4) embossed on the processor slot.
Reverse this procedure to install the processor.
82
Chapter 4 Removal and replacement procedures
Downloaded from LpManual.com Manuals
Power connector cable
Description
Spare part number
Power connector cable
454945-001
Before removing the power connector cable, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 41)
b.
Optical drive (see Optical drive on page 48)
c.
Keyboard (see Keyboard on page 50)
d.
Switch cover (see Switch cover on page 53)
e.
Display assembly (see Display assembly on page 55)
f.
Top cover (see Top cover on page 62)
g.
System board (see System board on page 72)
Remove the power connector cable:
1.
Turn the system board upside down, with the external monitor connector toward you.
2.
Disconnect the power connector cable (1) from the system board.
3.
Remove the power connector cable (2).
Reverse this procedure to install the power connector cable.
Component replacement procedures
Downloaded from LpManual.com Manuals
83
5
Setup Utility
WARNING! Only authorized technicians trained by HP must repair this equipment. All troubleshooting
and repair procedures are detailed to allow repair at only the subassembly or module level. Because of
the complexity of the individual boards and subassemblies, do not attempt to make repairs at the
component level or modify any printed wiring board. Improper repairs can create a safety hazard. Any
indication of component replacement or printed wiring board modification may void any warranty or
exchange allowances.
Starting the Setup Utility
The Setup Utility is a ROM-based information and customization utility that can be used even when your
Windows® operating system is not working or will not load.
NOTE: The fingerprint reader (select models only) does not work when accessing the Setup Utility.
The utility reports information about the computer and provides settings for startup, security, and other
preferences.
To start the Setup Utility:
1.
Turn on or restart the computer.
2.
Before Windows opens and while “Press <F10> to enter setup” is displayed in the lower-left corner
of the screen, press f10.
Changing the language of the Setup Utility
The following procedure explains how to change the language of the Setup Utility. If the Setup Utility is
not already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1.
To start the Setup Utility, turn on or restart the computer, and then press f10 while “Press <F10> to
enter setup” is displayed in the lower-left corner of the screen.
2.
Use the arrow keys to select System Configuration > Language, and then press enter.
3.
Press f5 or f6 (or use the arrow keys) to select a language, and then press enter to select a language.
4.
When a confirmation prompt with your preference selected is displayed, press enter to save your
preference.
5.
To set your preferences and exit the Setup Utility, press f10 and then follow the instructions on the
screen.
Your preferences go into effect when the computer restarts in Windows.
84
Chapter 5 Setup Utility
Downloaded from LpManual.com Manuals
Navigating and selecting in the Setup Utility
Because the Setup Utility is not Windows-based, it does not support the TouchPad. Navigation and
selection are by keystroke.
●
To choose a menu or a menu item, use the arrow keys.
●
To choose an item in a drop-down list or to toggle a field, for example an Enable/Disable field, use
either the arrow keys or f5 or f6.
●
To select an item, press enter.
●
To close a text box or return to the menu display, press esc.
●
To display additional navigation and selection information while the Setup Utility is open, press f1.
Displaying system information
The following procedure explains how to display system information in the Setup Utility. If the Setup Utility
is not open, begin at step 1. If the Setup Utility is open, begin at step 2.
1.
To start the Setup Utility, turn on or restart the computer, and then press f10 while “Press <F10>to
enter setup” is displayed in the lower-left corner of the screen.
2.
Access the system information by using the Main menu.
3.
To exit the Setup Utility without changing any settings, use the arrow keys to select Exit > Exit
Discarding Changes, and then press enter. (The computer restarts in Windows.)
Restoring default settings in the Setup Utility
The following procedure explains how to restore the Setup Utility default settings. If the Setup Utility is not
already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1.
To start the Setup Utility, turn on or restart the computer, and then press f10 while “Press <F10>to
enter setup” is displayed in the lower-left corner of the screen.
2.
Select Exit > Load Setup Defaults, and then press enter.
3.
When the Setup Confirmation is displayed, press enter to save your preferences.
4.
To set your preferences and exit the Setup Utility, press f10, and then follow the instructions on the
screen.
The Setup Utility default settings are set when you exit the Setup Utility and go into effect when the computer
restarts.
NOTE: Your password, security, and language settings are not changed when you restore the factory
default settings.
Navigating and selecting in the Setup Utility
Downloaded from LpManual.com Manuals
85
Using advanced Setup Utility features
This section describes the Setup Utility features recommended for all users. For more information about
the Setup Utility features recommended for advanced users only, refer to Help and Support, which is
accessible only when the computer is in Windows.
The Setup Utility features available for advanced users include a hard drive self-test, a Network Service
Boot, and settings for boot order preferences.
The “<F12> to boot from LAN” message that is displayed in the lower-left corner of the screen each time
the computer is started or restarted in Windows is the prompt for a Network Service Boot.
The “Press <F9> to change boot order” message that is displayed in the lower-left corner of the screen
each time the computer is started or restarted in Windows is the prompt to change the boot order.
Closing the Setup Utility
You can close the Setup Utility with or without saving changes.
●
To close the Setup Utility and save your changes from the current session, use either of the following
procedures:
◦
Press f10, and then follow the instructions on the screen.
– or –
◦
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the
arrow keys to select Exit > Exit Saving Changes, and then press enter.
When you use the f10 procedure, you are offered an option to return to the Setup Utility. When
you use the Exit Saving Changes procedure, the Setup Utility closes when you press enter.
●
To close the Setup Utility without saving your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow
keys to select Exit > Exit Discarding Changes, and then press enter.
After the Setup Utility closes, the computer restarts in Windows.
Setup Utility menus
The menu tables in this section provide an overview of Setup Utility options.
NOTE: Some of the Setup Utility menu items listed in this section may not be supported by your computer.
Main menu
86
Select
To do this
System information
●
View and change the system time and date.
●
View identification information about the computer.
●
View specification information about the processor, memory size,
system BIOS, and keyboard controller version (select models only).
Chapter 5 Setup Utility
Downloaded from LpManual.com Manuals
Security menu
Select
To do this
Administrator password
Enter, change, or delete an administrator password.
Power-On Password
Enter, change, or delete a power-on password.
System Configuration menu
Select
To do this
Language Support
Change the Setup Utility language.
Enhanced SATA support (select models only)
Enable/disable enhanced SATA mode.
Boot Options
Set the following boot options:
●
f10 and f12 Delay (sec.)―Set the delay for the f10 and f12
functions of the Setup Utility in intervals of 5 seconds each (0, 5,
10, 15, 20).
●
CD-ROM boot―Enable/disable boot from CD-ROM.
●
Floppy boot―Enable/disable boot from Floppy.
●
Internal Network Adapter boot―Enable/disable boot from
Internal Network Adapter.
●
Boot Order―Set the boot order for:
◦
USB Floppy
◦
ATAPI CD/DVD ROM Drive
◦
Hard drive
◦
USB Diskette on Key
◦
USB Hard drive
◦
Network adapter
Button Sound (select models only)
Enable/disable the Quick Launch Button tapping sound.
Virtualization Technology
Enable/disable the processor Virtualization Technology.
Processor C4 State
Enable/disable the processor C4 sleep state.
Diagnostics menu
Select
To do this
Hard Drive Self Test
Run a comprehensive self-test on the hard drive.
NOTE: On models with two hard drives, this menu option is called
the Primary Hard Disk Self Test.
Secondary Hard Drive Self Test (select models only)
Run a comprehensive self-test on a secondary hard drive.
Memory Test
Run a diagnostic test on the system memory.
Setup Utility menus
Downloaded from LpManual.com Manuals
87
6
Specifications
Computer specifications
Metric
U.S.
Length
25.7 cm
10.12 in
Width
35.7 cm
14.06 in
Height (front to rear
3.28 to 4.03 cm
1.29 to 1.59 in
Weight (with optical drive, hard drive, and battery)
2.9 kg
6.39 lbs
Dimensions
Input power
Operating voltage
18.5 V dc —19.0 V dc
Operating current
3.5 A or 4.74 A
Temperature
Operating (not writing to optical disc)
0°C to 35°C
32°F to 95°F
Operating (writing to optical disc)
5°C to 35°C
41°F to 95°F
Nonoperating
-20°C to 60°C
-4°F to 140°F
Relative humidity
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating (14.7 to 10.1 psia)
-15 m to 3,048 m
-50 ft to 10,000 ft
Nonoperating (14.7 to 4.4 psia)
-15 m to 12,192 m
-50 ft to 40,000 ft
Shock
Operating
125 g, 2 ms, half-sine
Nonoperating
200 g, 2 ms, half-sine
Random vibration
Operating
88
Chapter 6 Specifications
Downloaded from LpManual.com Manuals
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate
Metric
Nonoperating
U.S.
1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.
15.4-inch, WSXGA, BrightView display
specifications
Metric
U.S.
Height
20.7 cm
8.15 in
Width
33.1 cm
13.03 in
Diagonal
39.1 cm
15.39 in
Number of colors
Up to 16.8 million
Contrast ratio
200:1 (typical)
Brightness
180 nits (typical)
Dimensions
Pixel resolution
Pitch
0.197 × 0.197 mm
Format
1680× 1050
Configuration
RGB vertical stripe
Backlight
Cold cathode fluorescent tube (CCFT)
Character display
80 × 25
Total power consumption
7.0 W
Viewing angle
+/-40° horizontal, +-50° vertical (typical)
15.4-inch, WSXGA, BrightView display specifications
Downloaded from LpManual.com Manuals
89
Hard drive specifications
160-GB*
120-GB*
80-GB*
Height
9.5 mm
9.5 mm
9.5 mm
Width
70 mm
70 mm
70 mm
Weight
102 g
102 g
102 g
Interface type
SATA
SATA
SATA
Synchronous (maximum)
100 MB/sec
100 MB/sec
100 MB/sec
Security
ATA security
ATA security
ATA security
Single track
3 ms
3 ms
3 ms
Average
13 ms
13 ms
13 ms
Maximum
24 ms
24 ms
24 ms
Logical blocks
312,581,808
237,937,274
158,624,849
Dimensions
Transfer rate
Seek times (typical read, including setting)
Disk rotational speed
Operating temperature
NOTE:
5400 rpm
5°C to 55°C (41°F to 131°F)
Certain restrictions and exclusions apply. Consult technical support for details.
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Accessible capacity is less. Actual drive specifications
may differ slightly.
90
Chapter 6 Specifications
Downloaded from LpManual.com Manuals
DVD±RW and CD-RW Super Multi Double-Layer
Combo Drive specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CDROM, CD-ROM XA, MIXED MODE CD,
CD-I, CD-I Bridge (Photo-CD, Video CD),
Multisession CD (Photo-CD, CD-EXTRA,
Portfolio, CD-R, CD-RW), CD-R, CD-RW,
DVD-ROM (DVD-5, DVD-9, DVD-10,
DVD-18), DVD-R, DVD-RW, DVD+R, DVD
+RW, DVD-RAM
CD-R and CD-RW
Access time
CD
DVD
Random
< 175 ms
< 230 ms
Cache buffer
2 MB
DVD+R, DVD+RW, DVD-R, DVD-RW,
DVD-RAM
Data transfer rate
24X CD-ROM
3,600 KB/sec
8X DVD
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
2.4X DVD+R(9)
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
Transfer mode
Multiword DMA Mode
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive specifications
Downloaded from LpManual.com Manuals
91
System DMA specifications
Hardware DMA
System function
DMA0
Not applicable
DMA1*
Not applicable
DMA2*
Not applicable
DMA3
Not applicable
DMA4
Direct memory access controller
DMA5*
Available for PC Card
DMA6
Not assigned
DMA7
Not assigned
*PC Card controller can use DMA 1, 2, or 5.
System memory map specifications
92
Size
Memory address
System function
640 KB
00000000-0009FFFF
Base memory
128 KB
000A0000-000BFFFF
Video memory
48 KB
000C0000-000CBFFF
Video BIOS
160 KB
000C8000-000E7FFF
Unused
64 KB
000E8000-000FFFFF
System BIOS
15 MB
00100000-00FFFFFF
Extended memory
58 MB
04800000-07FFFFFF
Super extended memory
58 MB
04800000-07FFFFFF
Unused
2 MB
08000000-080FFFFF
Video memory (direct access)
4 GB
08200000-FFFEFFFF
Unused
64 KB
FFFF0000-FFFFFFFF
System BIOS
Chapter 6 Specifications
Downloaded from LpManual.com Manuals
System interrupt specifications
Hardware IRQ
System function
IRQ0
System timer
IRQ1
Standard 101-/102-Key or Microsoft® Natural Keyboard
IRQ2
Cascaded
IRQ3
Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD
IRQ4
COM1
IRQ5*
Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax
Modem with SmartCP
IRQ6
Diskette drive
IRQ7*
Parallel port
IRQ8
System CMOS/real-time clock
IRQ9*
Microsoft ACPI-compliant system
IRQ10*
Intel USB UHCI controller—24C2
Intel 82852/82855 GM/GME Graphic Controller
Realtek RTL8139 Family PCI Fast Ethernet Controller
IRQ11
Intel USB EHCI controller—24CD
Intel USB UHCI controller—24C4
Intel USB UHCI controller—24C7
Intel Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
IRQ12
Synaptics PS/2 TouchPad
IRQ13
Numeric data processor
IRQ14
Primary IDE channel
IRQ15
Secondary IDE channel
*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
NOTE: PC Cards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial port
may assert IRQ3 or IRQ4.
System interrupt specifications
Downloaded from LpManual.com Manuals
93
System I/O address specifications
94
I/O address (hex)
System function (shipping configuration)
000 - 00F
DMA controller no. 1
010 - 01F
Unused
020 - 021
Interrupt controller no. 1
022 - 024
Opti chipset configuration registers
025 - 03F
Unused
02E - 02F
87334 “Super I/O” configuration for CPU
040 - 05F
Counter/timer registers
044 - 05F
Unused
060
Keyboard controller
061
Port B
062 - 063
Unused
064
Keyboard controller
065 - 06F
Unused
070 - 071
NMI enable/RTC
072 - 07F
Unused
080 - 08F
DMA page registers
090 - 091
Unused
092
Port A
093 - 09F
Unused
0A0 - 0A1
Interrupt controller no. 2
I/O Address (hex)
System function (shipping configuration)
0A2 - 0BF
Unused
0C0 - 0DF
DMA controller no. 2
0E0 - 0EF
Unused
0F0 - 0F1
Coprocessor busy clear/reset
0F2 - 0FF
Unused
100 - 16F
Unused
170 - 177
Secondary fixed disk controller
178 - 1EF
Unused
1F0 - 1F7
Primary fixed disk controller
1F8 - 200
Unused
201
JoyStick (decoded in ESS1688)
202 - 21F
Unused
Chapter 6 Specifications
Downloaded from LpManual.com Manuals
I/O address (hex)
System function (shipping configuration)
220 - 22F
Entertainment audio
230 - 26D
Unused
26E - 26
Unused
278 - 27F
Unused
280 - 2AB
Unused
2A0 - 2A7
Unused
2A8 - 2E7
Unused
2E8 - 2EF
Reserved serial port
2F0 - 2F7
Unused
2F8 - 2FF
Infrared port
300 - 31F
Unused
320 - 36F
Unused
370 - 377
Secondary diskette drive controller
378 - 37F
Parallel port (LPT1/default)
380 - 387
Unused
388 - 38B
FM synthesizer—OPL3
38C - 3AF
Unused
3B0 - 3BB
VGA
3BC - 3BF
Reserved (parallel port/no EPP support)
3C0 - 3DF
VGA
3E0 - 3E1
PC Card controller in CPU
3E2 - 3E3
Unused
3E8 - 3EF
Internal modem
3F0 - 3F7
“A” diskette controller
3F8 - 3FF
Serial port (COM1/default)
CF8 - CFB
PCI configuration index register (PCIDIVO-1)
CFC - CFF
PCI configuration data register (PCIDIVO-1)
System I/O address specifications
Downloaded from LpManual.com Manuals
95
7
Screw listing
This section provides specification and reference information for the screws and screw locks used in the
computer. All screws and screw locks listed in this section are available in the Screw Kit, spare part number
454951-001, and the Display Screw Kit, spare part number 454918-001.
96
Chapter 7 Screw listing
Downloaded from LpManual.com Manuals
Phillips PM2.0×5.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
4
5.0 mm
2.0 mm
5.0 mm
Where used:
(1) Two captive screws (secured by C-clips) that secure the hard drive bay cover to the computer
(2) Two captive screws (secured by C-clips) that secure the memory/wireless module compartment cover
to the computer
Phillips PM2.0×5.0 captive screw
Downloaded from LpManual.com Manuals
97
Phillips PM3.0×3.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
4
3.0 mm
3.0 mm
5.0 mm
Where used: 4 screws that secure the hard drive bracket to the hard drive
98
Chapter 7 Screw listing
Downloaded from LpManual.com Manuals
Black Phillips PM2.0×3.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
2
3.0 mm
2.0 mm
4.0 mm
Where used: 2 screws that secure the camera module to the display
Black Phillips PM2.0×3.0 screw
Downloaded from LpManual.com Manuals
99
Black Phillips PM2.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
8
4.0 mm
2.0 mm
5.0 mm
Where used: 2 screws that secure the WLAN module to the system board
100 Chapter 7 Screw listing
Downloaded from LpManual.com Manuals
Where used: 2 screws that secure the optical drive bracket to the optical drive
Where used: One screw that secures the caps lock LED board to the top cover
Where used: 3 screws that secure the card reader board to the system board
Black Phillips PM2.0×4.0 screw 101
Downloaded from LpManual.com Manuals
Phillips PM2.5×9.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
22
9.0 mm
2.5 mm
5.0 mm
Where used:
(1) One screw that secures the optical drive to the computer
(2) Three screws that secure the keyboard to the computer
(3) Four screws that secure the switch cover to the computer
102 Chapter 7 Screw listing
Downloaded from LpManual.com Manuals
Where used: 4 screws that secure the display assembly to the computer
Where used: Ten screws that secure the top cover to the base enclosure
Phillips PM2.5×9.0 screw 103
Downloaded from LpManual.com Manuals
Phillips PM2.5×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
19
4.0 mm
2.5 mm
5.0 mm
Where used: 4 screws that secure the switch cover to the computer
Where used: 6 screws that secure the display panel to the display enclosure
104 Chapter 7 Screw listing
Downloaded from LpManual.com Manuals
Where used: 2 screws that secure the wireless antenna transceivers to the display enclosure
Where used: 2 screws that secure the top cover to the base enclosure
Where used: One screw that secures the USB board to the base enclosure
Phillips PM2.5×4.0 screw 105
Downloaded from LpManual.com Manuals
Where used: 2 screws that secure the speakers to the base enclosure
Where used: One screw that secures the fan to the base enclosure
106 Chapter 7 Screw listing
Downloaded from LpManual.com Manuals
Where used: One screw that secures the system board to the base enclosure
Phillips PM2.5×7.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
8
7.0 mm
2.5 mm
5.0 mm
Where used: 8 screws that secure the display bezel to the display assembly
Phillips PM2.5×7.0 screw 107
Downloaded from LpManual.com Manuals
Silver Phillips PM2.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
8
4.0 mm
2.0 mm
4.5 mm
Where used: 8 screws that secure the display hinges to the display panel
108 Chapter 7 Screw listing
Downloaded from LpManual.com Manuals
Phillips PM2.5×6.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
4
6.0 mm
2.5 mm
5.0 mm
Where used: 4 screws that secure the heat sink to the system board
Phillips PM2.5×6.0 captive screw 109
Downloaded from LpManual.com Manuals
8
Backup and recovery
Recovering system information
Tools provided by the operating system and Recovery Manager software are designed to help you with
the following tasks for safeguarding your information and restoring it in case of a system failure:
●
Backing up your information regularly to protect your important system files.
●
Making a set of recovery discs (Recovery Manager software feature). Recovery discs are used to
start up (boot) your computer and restore the operating system and software programs to factory
settings in case of system failure or instability.
●
Creating system restore points (operating system feature). System restore points allow you to reverse
undesirable changes to your computer by restoring the computer to an earlier state.
●
Recovering a program or driver (Recovery Manager software feature). This feature helps you reinstall
a program or driver without performing a full system recovery.
●
Performing a full system recovery (Recovery Manager software feature). With Recovery Manager,
you can recover your full factory image if you experience system failure or instability. Recovery
Manager works from a dedicated recovery partition on the hard drive or from recovery discs you
create.
Backing up your information
When to back up
●
On a regularly scheduled basis
NOTE: Set reminders to back up your information periodically.
●
Before the computer is repaired or restored
●
Before you add or modify hardware or software
110 Chapter 8 Backup and recovery
Downloaded from LpManual.com Manuals
Backup suggestions
●
Create a set of recovery discs using Recovery Manager.
●
Create system restore points using the Windows® System Restore feature, and periodically copy
them to disc.
●
Store personal files in the Documents folder and back up these folders periodically.
●
Back up templates stored in their associated programs.
●
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
a.
Display the screen.
b.
Copy the screen:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c.
Open a word-processing document, and then select Edit > Paste.
Using system restore points
When you back up your system, you are creating a system restore point. A system restore point allows
you to save and name a snapshot of your hard drive at a specific point in time. You can then recover
back to that point if you want to reverse subsequent changes made to your system.
NOTE: Recovering to an earlier restore point does not affect data files saved or e-mails created since
the last restore point.
You also can create additional restore points to provide increased protection for your system files and
settings.
When to create restore points
●
Before you add or extensively modify software or hardware.
●
Periodically, whenever the system is performing optimally.
NOTE: If you revert to a restore point and then change your mind, you can reverse the restoration.
Create a system restore point
1.
Select Start > Control Panel > System and Maintenance > System.
2.
In the left pane, click System protection.
3.
Click the System Protection tab.
4.
Under Automatic restore points, select the disk for which you want to create a restore point.
5.
Click Create.
Recovering system information 111
Downloaded from LpManual.com Manuals
The System Protection window opens.
6.
Follow the on-screen instructions.
112 Chapter 8 Backup and recovery
Downloaded from LpManual.com Manuals
Restore to a previous date and time
To revert to a restore point (created at a previous date and time), when the computer was functioning
optimally, follow these steps:
1.
Select Start > Control Panel > System and Maintenance > System.
2.
In the left pane, click System protection.
3.
Click the System Protection tab.
4.
Click the System Restore button, and then click Next.
The System Restore window opens.
5.
Follow the on-screen instructions.
Creating recovery discs
After setting up the computer for the first time, be sure to create a set of recovery discs of the full factory
image. The recovery discs are used to start up (boot) the computer and recover the operating system and
software to factory settings in case of system instability or failure.
NOTE: Handle these discs carefully and keep them in a safe place. The software allows the creation of
only one set of recovery discs.
Note the following guidelines before creating recovery discs:
●
Use any of the following types of discs: CD-R, DVD+R, DVD+R DL, DVD-R, or DVD-R DL (purchased
separately). The discs you use will depend on the type of optical drive installed in your computer.
Because DVDs store more information than CDs, DVDs and DVDs with double-layer (DL) support
reduce the number of discs required.
NOTE: Read-write discs, such as CD-RW, DVD+RW, and DVD-RW, are not compatible with the
Recovery Manager software.
●
The computer must be connected to AC power during this process.
●
Only one set of recovery discs can be created per computer.
●
Number each disc before inserting it into the computer optical drive.
●
If necessary, you can exit the program before you have finished creating the recovery discs. The next
time you open Recovery Manager, you will be prompted to continue the disc creation process.
To create a set of recovery discs:
1.
Select Start > All Programs > Recovery Manager > Recovery Manager.
Recovery Manager opens.
2.
Click Advanced Options.
NOTE: If you are operating the computer on battery power, you will be prompted to connect to
AC power before you can go to the next step.
3.
Click Recovery disc creation, and then click Next.
4.
Follow the on-screen instructions.
Recovering system information 113
Downloaded from LpManual.com Manuals
Performing a recovery
NOTE: You can only recover files that you have previously backed up. HP recommends that you use
Recovery Manager to create an entire drive backup as soon as you set up your computer.
Recovery Manager software allows you to repair or restore the system if you experience system failure or
instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery
partition on the hard drive.
NOTE: Windows has its own built-in repair features, such as System Restore and driver rollback
capabilities. If you have not already tried these features, try them before using Recovery Manager.
NOTE: Recovery Manager only recovers software that was preinstalled at the factory. Software not
provided with this computer must be reinstalled from the disc provided by the manufacturer or downloaded
from the manufacturer's Web site.
Recovering from the recovery discs
To restore the system from the recovery discs:
1.
Back up all personal files.
2.
Insert the first recovery disc into the optical drive and restart the computer.
3.
Follow the on-screen instructions.
Recovering from the partition on the hard drive
You can perform a recovery from the partition on the hard drive from either the Start button or f11.
To restore the system from the partition, follow these steps:
1.
Access Recovery Manager in either of the following ways:
●
Select Start > All Programs > Recovery Manager > Recovery Manager.
– or –
●
Restart the computer and press f11 while the “Press <F11> for recovery” message is displayed
on the screen. Then select Recovery Manager.
Recovery Manager opens.
2.
Click Advanced Options.
3.
Click System recovery, and then click Next.
4.
Follow the on-screen instructions.
114 Chapter 8 Backup and recovery
Downloaded from LpManual.com Manuals
9
Connector pin assignments
Audio-out (headphone)
Pin
Signal
1
Audio out, left channel
2
Audio out, right channel
3
Ground
Audio-in (microphone)
Pin
Signal
1
Audio signal in
2
Audio signal in
3
Ground
Audio-out (headphone) 115
Downloaded from LpManual.com Manuals
External monitor
Pin
Signal
1
Red analog
2
Green analog
3
Blue analog
4
Not connected
5
Ground
6
Ground analog
7
Ground analog
8
Ground analog
9
+5 VDC
10
Ground
11
Monitor detect
12
DDC 2B data
13
Horizontal sync
14
Vertical sync
15
DDC 2B clock
116 Chapter 9 Connector pin assignments
Downloaded from LpManual.com Manuals
RJ-11 (modem)
Pin
Signal
1
Unused
2
Tip
3
Ring
4
Unused
5
Unused
6
Unused
RJ-45 (network)
Pin
Signal
1
Transmit +
2
Transmit -
3
Receive +
4
Unused
5
Unused
6
Receive -
7
Unused
8
Unused
RJ-11 (modem) 117
Downloaded from LpManual.com Manuals
S-Video-out
Pin
Signal
1
S-VHS color (C) signal
2
Composite video signal
3
S-VHS intensity (Y) signal
4
S-VHS color ground
5
TV-CD
6
S-VHS intensity ground
7
Composite video ground
Universal Serial Bus
Pin
Signal
1
+5 VDC
2
Data -
3
Data +
4
Ground
118 Chapter 9 Connector pin assignments
Downloaded from LpManual.com Manuals
10 Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the country
or region where the equipment is purchased.
Power cord sets for use in other countries or regions must meet the requirements of the country or region
where the computer is used.
Requirements for all countries or regions
The requirements listed below are applicable to all countries or regions:
●
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
●
All power cord sets must be approved by an acceptable accredited agency responsible for evaluation
in the country or region where the power cord set will be used.
●
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating
of 125 or 250 V AC, as required by each country or region’s power system.
●
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard
Sheet C13 connector for mating with the appliance inlet on the back of the computer.
Requirements for all countries or regions 119
Downloaded from LpManual.com Manuals
Requirements for specific countries or regions
Country/region
Accredited agency
Applicable note number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
South Korea
EK
4
The Netherlands
KEMA
1
Norway
NEMKO
1
The People's Republic of China
CCC
5
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
The United Kingdom
BSI
1
The United States
UL
2
1.
The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
2.
The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding
type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3.
The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug
must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4.
The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be
used.
5.
The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be
used.
120 Chapter 10 Power cord set requirements
Downloaded from LpManual.com Manuals
11 Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household
waste. Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING! The backlight contains mercury. Caution must be exercised when removing and handling
the backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this appendix can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight.
Careful handling must be exercised when removing these components.
NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly
that might require special handling at end-of-life. Disposal of mercury may be regulated because of
environmental considerations. For disposal or recycling information, contact your local authorities, or see
the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE: The procedures provided in this appendix are general disassembly instructions. Specific details,
such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from one
computer model to another.
Battery 121
Downloaded from LpManual.com Manuals
Perform the following steps to disassemble the display assembly:
1.
Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.
2.
Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the
display bezel until the bezel disengages from the display assembly.
3.
Remove the display bezel (3).
122 Chapter 11 Recycling
Downloaded from LpManual.com Manuals
4.
Disconnect all display panel cables (1) from the display inverter and remove the inverter (2).
5.
Remove all screws (1) that secure the display panel assembly to the display enclosure.
6.
Remove the display panel assembly (2) from the display enclosure.
7.
Turn the display panel assembly upside down.
8.
Remove all screws that secure the display panel frame to the display panel.
9.
Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display
panel frame.
Display 123
Downloaded from LpManual.com Manuals
10. Remove the display panel frame (2) from the display panel.
11. Remove the screws (1) that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover (2) and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
124 Chapter 11 Recycling
Downloaded from LpManual.com Manuals
15. Remove the backlight cables (1) from the clip (2) in the display panel.
16. Turn the display panel upside down.
17. Remove the backlight frame from the display panel.
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
Display 125
Downloaded from LpManual.com Manuals
18. Remove the backlight from the backlight frame.
19. Disconnect the display cable (1) from the LCD panel.
20. Remove the screws (2) that secure the LCD panel to the display rear panel.
21. Release the LCD panel (3) from the display rear panel.
22. Release the tape (4) that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
126 Chapter 11 Recycling
Downloaded from LpManual.com Manuals
Index
A
AC adapter, spare part
number 24, 30
administrator password 87
advanced Setup Utility
features 86
antenna
illustrated 20
removal 59
spare part number 20
applications key, Windows 7
audio, product description 3
audio-in jack
location 10
pin assignments 115
audio-out jack
location 10
pin assignments 115
B
backpack, spare part
number 24, 26
backup 110
base enclosure, spare part
numbers 17, 28
battery
location 12
removal 40
spare part number 17, 28,
40
battery bay 12
battery light 8
battery release latch 12
boot options 87
boot order 87
bottom components 12
button components 6
button sound 87
buttons
power 6
wireless 6
C
cables, service considerations 33
camera cable
spare part numbers 31
camera light location 5
camera location 5
camera module
removal 60
spare part number 60
spare part numbers 31
caps lock LED board
removal 64
spare part number 16, 29,
64
caps lock light 8
card reader board
removal 77
spare part number 16, 29,
77
carrying case, spare part
number 24, 26
changing the Setup Utility
language 84
chipset, product description 1
closing the Setup Utility 86
CMOS clearing 37
components
bottom 12
buttons 6
display 5
front 5, 10
key 7
left-side 11
lights 8
right-side 10
TouchPad 9
composite audio and S-Video cable,
spare part number 24, 26
computer feet
locations 39
spare part number 39
computer specifications 88
connector pin assignments
audio-in 115
audio-out 115
external monitor 116
headphone 115
microphone 115
modem 117
monitor 116
network 117
RJ-11 117
RJ-45 117
S-Video-out 118
Universal Serial Bus (USB) 118
connectors, service
considerations 33
D
Diagnostics menu 87
Digital Media Slot 11
diskette drive
precautions 33
product description 3
display assembly
removal 55
spare part numbers 15, 28,
31, 55
display bezel
illustrated 20
removal 57
spare part numbers 20, 28,
30, 31, 57
Display Cable Kit, spare part
number 20, 28, 59
Index 127
Downloaded from LpManual.com Manuals
display components
illustrated 20
recycling 121
spare part numbers 20
display enclosure
illustrated 20
spare part numbers 20, 28,
30
display hinge
illustrated 20
removal 58
spare part number 20, 28,
58
Display Hinge Kit, spare part
number 20
display inverter
illustrated 20
spare part number 20, 28
display panel
illustrated 20
product description 2
removal 58, 59
spare part number 20, 27,
59
Display Rubber Kit, spare part
number 21, 28
Display Screw Kit, spare part
number 21, 28
display specifications 89
display switch 5
docking support, product
description 3
drive light 8
drives
boot order 87
preventing damage 33
DVB-T antenna adapter, spare part
number 24, 26
DVB-T tuner, spare part
number 24, 26
DVD/CD-RW Combo Drive
precautions 33
removal 48
spare part number 19, 23,
28, 48
specifications 91
DVD±RW and CD-RW Combo Drive
precautions 33
removal 48
128 Index
Downloaded from LpManual.com Manuals
spare part numbers
28, 48
specifications 91
19, 23,
E
electrostatic discharge 34
enhanced SATA support 87
esc key 7
Ethernet, product description 3
external media cards, product
description 3
external monitor port
location 11
pin assignments 116
F
fan
removal 68
spare part number 16, 29,
68
feet
locations 39
spare part number 39
fingerprint reader 84
fn key 7
front components 5, 10
function keys 7
G
graphics, product description
grounding equipment and
methods 36
2
H
hard drive
precautions 33
product description 2
removal 41
spare part numbers 18, 23,
28, 41
specifications 90
hard drive bay 12
hard drive bay cover
illustrated 22
removal 41
Hard Drive Kit, spare part
number 18, 23, 28
hard drive self test 87
headphone jack
location 10
pin assignments 115
headset, spare part number 24,
26
heat sink
removal 79
spare part number 17, 29,
79
I
I/O address specifications 94
infrared emitter, spare part
number 24, 26
interrupt specifications 93
inverter
removal 58
spare part number 20, 28,
58
J
jacks
audio-in 10
audio-out 10
headphone 10
microphone 10
modem 11
network 11
RJ-11 11
RJ-45 11
S-Video-out jack 11
K
key components 7
keyboard
product description 4
removal 50
spare part numbers 15, 29,
50
keypad keys 7
keys
esc 7
fn 7
function 7
Windows applications 7
Windows logo 7
L
language support 84, 87
LCD logo kit
spare part number 31
left-side components 11
light components 8
lights
battery 8
caps lock 8
drive 8
num lock 8
optical drive 10
power 8
wireless 8
network jack
location 11
pin assignments 117
num lock light 8
M
main menu 86
mass storage devices, spare part
numbers 23
memory map specifications 92
memory module
product description 2
removal 43
spare part numbers 18, 28,
43
memory/wireless module
compartment 12
memory/wireless module
compartment cover
illustrated 22
removal 43
spare part number 43
microphone
illustrated 20
location 5
product description 3
removal 59
microphone jack
location 10
pin assignments 115
model name 1
modem cable, spare part
number 16, 29
modem jack
location 11
pin assignments 117
modem, product description 3
monitor port
location 11
pin assignments 116
mouse, spare part numbers 24,
26
N
navigating in the Setup Utility
85
O
operating system, product
description 4
optical drive
location 10
precautions 33
product description 2
removal 48
spare part numbers 19, 23,
28, 48
specifications 91
Optical Drive Kit, spare part
number 19, 23, 28
optical drive light, location 10
P
packing guidelines 35
password clearing 37
passwords 87
plastic parts 32
Plastics Kit
contents 22
spare part number 16, 22,
28
pointing device
components 9
product description 4
ports
external monitor port 11
monitor port 11
product description 3
Universal Serial Bus (USB) 10,
11
power button 6
power connector 11
power connector cable
removal 83
spare part number 16, 29,
83
power cord
set requirements 119
spare part numbers 24, 26
power light 8
power requirements, product
description 4
power-on password 87
processor
product description 1
removal 81
spare part numbers 16, 27,
30, 81
Processor C4 State 87
product description
audio 3
chipset 1
diskette drive 3
display panel 2
docking support 3
Ethernet 3
external media cards 3
graphics 2
hard drives 2
keyboard 4
memory module 2
microphone 3
modem 3
operating system 4
optical drives 2
pointing devices 4
ports 3
power requirements 4
processors 1
product name 1
security 4
serviceability 4
wireless 3
product name 1
R
recovery discs 113
recovery, system 114
remote control, spare part
numbers 24, 26
removal/replacement
preliminaries 32
procedures 38
restore points 111
RF input adapter cable, spare part
number 24, 26
right-side components 10
RJ-11 jack
location 11
pin assignments 117
Index 129
Downloaded from LpManual.com Manuals
RJ-45 jack
location 11
pin assignments 117
RTC battery
removal 75
spare part number 17, 29,
75
Rubber Foot Kit, spare part
number 17, 29, 39
S
S-Video-out jack
location 11
pin assignments 118
Screw Kit
contents 96
spare part number 25, 29
screw listing 96
secondary hard drive self test 87
security cable slot 10
Security menu 87
security, product description 4
selecting in the Setup Utility 85
serial number 13, 38
service considerations 32
serviceability, product
description 4
Setup Utility
changing the language 84
Diagnostics menu 87
displaying system
information 85
Main menu 86
navigating 85
overview 84
Security menu 87
selecting 85
starting 84
System Configuration menu 87
using advanced features 86
speakers
removal 70
spare part number 16, 29,
70
specifications
computer 88
display 89
DVD/CD-RW Combo Drive 91
DVD±RW and CD-RW Combo
Drive 91
130 Index
Downloaded from LpManual.com Manuals
hard drive 90
I/O addresses 94
interrupts 93
memory map 92
optical drive 91
system DMA 92
static-shielding materials 36
switch cover
removal 53
spare part number 15, 29,
53
system board
removal 72
spare part numbers 16, 27,
28, 30, 72
System Configuration menu 87
system DMA 92
system information 85, 86
system memory map 92
T
thermal paste, replacement 80
tools required 32
top components 6
top cover
removal 62
spare part number 16, 28,
31, 62
TouchPad components
buttons 9
left button 9
light 9
on/off button 9
right button 9
scroll zone 9
TouchPad 9
transporting guidelines 35
TV tuner antenna, spare part
number 24, 26
TV tuner, spare part number 24,
26
U
Universal Serial Bus (USB) port
locations 10, 11
pin assignments 118
unknown password 37
USB board
removal 66
spare part number
66
16, 29,
V
vents 11, 12
Virtualization Technology
volume hotkeys 6
87
W
Windows applications key 7
Windows logo key 7
wireless antenna
illustrated 20
removal 59
spare part number 20
Wireless Antenna Kit, spare part
number 20
wireless button 6
wireless light 8
wireless, product description 3
WLAN module
removal 45
spare part numbers 17, 27,
45
workstation guidelines 35
Downloaded from LpManual.com Manuals

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement