Shinybow USA SB-6340R Instruction manual

Shinybow USA SB-6340R Instruction manual
INSTRUCTION MANUAL
M U LT IM EDIA AUDIO A ND V IS UA L
MODEL : SB-6340R & SB-6340T
CAT5 COMPONENT EXTENDER
Receiver
Transmitter
CAT5 YUV COMPONENT EXTENDER
CAT5 Transmitter/Repeater/Receiver Series
Thank you for purchasing the YUV CAT5 SB-6340T Transmitter or SB-6340R Receiver. You will find this unit
easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use
this Extender.
SAFETY INFORMATION
1.
To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2.
Follow all instructions printed on unit chassis for proper operation.
3.
To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4.
Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5.
Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6.
Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7.
Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8.
Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9.
AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
TABLE OF CONTENTS
CONTENTS
SAFETY PRECAUTIONS
TABLE OF CONTENTS ......................................................1
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
PACKAGE CONTENTS .................................................... 1
FEATURES ....................................................................... 2
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
SPECIFICATIONS ............................................................ 2
TYPICAL HOOKUP AND OPERATION ............................ 3
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
IR EXTENDER ................................................................. 4
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
INTRODUCTION
Congratulations on your purchase of one the most innovative CAT5
Transmitter/Repeater/Receiver product on the market Today. The
SB-6340 is a transmitte its driving Component Video (YPBPR)
signals over long lines by category cable to CAT5 component
video receiver or repeater as model of SB-6130R, SB-6230R, SB6330R and SB-6340R. There are use high performance HDTV
Component Video (YPBPR) 480p-720p-1080i- 1080p driving with
a ADC’s digital signal. Signals Component Video with a maximum
extension of 1000ft between transmitter and receiver. And use
category 5 cable. The terminators are RJ-45 (Category 5) jack and
Component video sockets .
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for sufficient space for air to circulate around the unit.
DISCLAIMERS
PACKAGE CONTENTS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
Check that you have the following components;
• SB-6340 Transmitter or Repeater or Receiver
• Users Guide
• AC/DC Adapter: 12VDC, @300mA
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
Input: Component Video(YPBPR)
Power Input: SB-6340T +12V [email protected]
SB-6340R +12V DC @300mA
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent
© Copyright 1997. All Rights Reserved.
Version 1.4 MAR 2014
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
1
FEATURES & SPECIFICATIONS
FEATURES
SB-6340 TRANSMITTER
• Input: 1 x Component Video
• Output: 1 x Component Video (YPBPR)
4 x CATS (Tx) Transmitter Distribution
SB-6340 RECEIVER
• Input: 1 x CAT5 (Rx) Receiver
• Output: 1 x CATS (Tx) Repeater
2 x Component Video (YPBPR) Distribution
SPECIFICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Model Number: SB-6340T Transmitter, SB-6340R Repeater & Receiver
Tx, Rx Input/Output: Transmitter & Repeater + Receiver
Type of Signals: Component Video (YPBPR)
SB-6340 connect to Receivers list:
• SB-6130R
• SB-6230R
• SB-6330R
• SB-6340R
Cable for CAT5, 5e, 6:
• YUV Resolution:
• 1080i (1920 x1080) 450 feet
• 720p (1080 x 720) 600 feet
• 480p (720 x 480) 1000 feet
Video Bandwidth:
• Tx : 400 Mhz, 13dB full power
• Rx : 270MHz 1090V/[email protected]= +1
Tx Slew Rate: 2000 V/us
Video Maximum Input Levels: 1.45 Vp-p
Rx High input Impedance: 1 MΩ differential
Audio Frequency Response: 20Hz to 20KHz, +/-1db
Audio Maximum Input Levels: 3.1 Vp-p (line level)
Low Distortion:
• Tx: 68dB [email protected] Mhz 200Ω load
• Rx: 1 [email protected]
In/Out Terminal: RJ-45 Jack, HD-15 and Ear phone Jack female connectors
Size(LxWxH): 2.75 in x 4.40 in x 1 in (70x112x26mm)
Net Weight (Unit only): 0.4 lbs. (0.24kg) Approx
Power Consumed: @300mA
Power Source: DC 12 Volts @300mA~660mA
As product improvements are continuous, specifications are subject to change without notice.
2
TYPICAL HOOKUP AND OPERATION
SB-6340
TRANSMITTER
Front:
Input: 1x Component
Video(YPBPR)
RECEIVER
Front:
Input: 1x CAT5 (Rx)
Receiver
Output: 1x CAT5 (Tx)
Repeater
Power Output: DC12V,
@300mA
Rear:
Output: 1x Component
Video (YPBPR)
4x CAT5 (Tx)
Transmitter
Rear:
Output: 2x Component
Video (YPBPR)
Power Output:
DC12V, @300mA
Component Video(YPBPR) Transmitter signals : 480p(720x480), 720p(1080x720), 1080i(1 920x1080)
Safeguards and Precautions
A. Keep this unit away from fire, extremely hot areas, water or moisture of any kind.
B. Do not place this unit on any support that is not firm, level and strong.
C. Do not service the unit yourself. Opening the unit’s housing will void the warranty.
D. Servicing must be by ShinybowUSA or by an authorized technician.
C. Illegal duplication of copyrighted material is strictly prohibited by Federal Laws.
CAT5 VGA(RGBHV) & STEREO AUDIO EXTENDER
APPLICATIONS
TX : Video line driver, Digital line driver, Low power differential ADC driver, Signal-ended input to differential output driver
RX : High speed differential line receivers, Differential-to-sigle ended converters, High speed instrumentation amps, level shifting.
3
IR EXTENDER
IR RECEIVER:
1. SB-100
IR 300M Receiver
Device
Cable (3C)
IR Receiver (SB-100)
R oHS /95/E C
IR E XT. in
RS - 232
IR EXT .
INP UT
DC 12V
4
3
UT
4
-2
3
-4
UT
IR
2
R IX
IN P
I MAT
SW
1
HDM
1
S WIT
UT
2
IN P
1
SB-100
C HE
-3
R
3
UT
ER
2
IN P
P OW
2
ON
1
IN P
IR Rx
OFF
-1
3
4
4
R S -232
SB-100 IR Receiver Set
2. SB-100C
SB-100 Maximum Distance ~ 984 feet (300 meters)
IR 2M Receiver
Device
Cable (3C)
IR Receiver (SB-100C)
IR Receiver cable 6ft (2M)
R oHS /95/E C
IR E XT. in
RS - 232
IR EXT .
INP UT
DC 12V
4
3
UT
4
-2
3
R
-3
C HE
3
SB-100C IR Receiver Cable
SW
SB-100
IR
UT
-4
IN P
S WIT
UT
2
R IX
IN P
I MAT
1
1
HDM
2
ER
2
IN P
P OW
UT
2
ON
1
1
IR Rx
IN P
OFF
-1
3
4
4
R S -232
SB-100C Maximum Distance ~ 6 feet (2 meters)
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
PIN CONFIGURATION:
SB-100 and SB-100C Receiver Pin configuration
Tip: Signal
Tip
Ring :VCC
Sleeve: GND
Ring
Ring
Sleeve
VCC (Ring)
GND (Sleeve)
Sleeve
SB-100 IR Receiver Set
Tip (center)
Signal (center)
SB-100 Maximum Distance ~ 984 feet (300 meters)
IR Receiver cable 6ft (2M)
Sleeve
Tip: Signal
Tip
Ring: NC
Sleeve: GND
Ring
Ring
GND (Sleeve)
SB-100C IR Receiver Cable
Sleeve
Tip (center)
Signal (center)
SB-100C Maximum Distance ~ 6 feet (2 meters)
Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug
(aka: stereo plug). Using a 2-conductor plug will short out the power supply. Always make connections with the
switcher power off.
4
IR EXTENDER
IR EMITTER:
1. SB-101
IR 300M Transmitter
DC 12V
Device
Cable (3C)
IR out
IR in
CAT6/6a/7
From
Receiver
To
Receiver
OUTPUT
IR Transmitter (SB-101)
R oHS /95/E C
IR Tx
SB-101
SB-101 IR Transmitter Set
2. SB-101C
SB-101 Maximum Distance ~ 984 feet (300 meters)
IR 2M Transmitter
Device
Cable (3C)
IR Transmitter (SB-101C)
IR Transmitter cable 6ft (2M)
DC 12V
IR out
IR in
CAT6/6a/7
From
Receiver
To
Receiver
OUTPUT
R oHS /95/E C
IR Tx
SB-101C
SB-101C Transmitter Cable
SB-101C Maximum Distance ~ 6 feet (2 meters)
*** When you plug the External IR extender into the switcher, the front panel IR transmitter remains active. ***
PIN CONFIGURATION:
SB-101 and SB-101C Transmitter Pin configuration
Tip: Signal
Tip
Ring :VCC
Sleeve: GND
Ring
Ring
Sleeve
VCC (Ring)
GND (Sleeve)
Sleeve
SB-101 IR Transmitter Set
Tip (center)
Signal (center)
SB-101 Maximum Distance ~ 984 feet (300 meters)
IR Transmitter cable 6ft (2M)
Sleeve
Tip: Signal
Tip
Ring: NC
Sleeve: GND
Ring
Ring
GND (Sleeve)
SB-101C Transmitter Cable
Sleeve
Tip (center)
Signal (center)
SB-101C Maximum Distance ~ 6 feet (2 meters)
Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug
(aka: stereo plug). Using a 2-conductor plug will short out the power supply. Always make connections with the
switcher power off.
5
LIMITED WARRANTY
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA,
Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime,
without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product
are licensed to you by SHINYBOWUSA, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “SHINYBOWUSA”) for your
personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only.
SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the
intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the Product, and you may not copy or
use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.
The functionality and usability of the Product is controlled by SHINYBOWUSA, Inc. from its offices within the State of Texas, United States of America. SHINYBOWUSA
makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.
Disclaimers and Limitation of Liability
SHINYBOWUSA may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT
OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should
not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical
inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
SHINYBOWUSA DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST
OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING
BY SHINYBOWUSA.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS,
EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL
SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE)
EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
6
M U LT IM ED IA AUDIO A ND V IS UA L
122 Rose Ln. Suite 303 | Frisco, Texas 75034
1-877-SHINY-USA
1-877-744-6987
1-972-377-2508
[email protected]
www.shinybowusa.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement