BKI DNF Service manual

BKI DNF Service manual
Electric Pressure Fryer
MODELS FKM, FKM-F, & FKM-FC
SERVICE MANUAL
Serial Numbers 121836 and higher
Warranty Information
LIMITED ONE YEAR WARRANTY
BKI (The “Company”) warrants to the original purchaser/user, that at time of shipment from the Company
factory, this equipment will be free from defect in materials and workmanship. Written notice of a claim
under this Warranty must be given within ONE YEAR AND THREE MONTHS from date of shipment from
the factory. Defective conditions caused by abnormal use or misuse, lack of maintenance, damage by
third parties, alterations by unauthorized personnel, acts of God, failure to follow installation instructions
or any other events beyond the control of the company will NOT be covered under Warranty. The
obligation of the Company under this Warranty shall be limited to repairing or replacing (at the option of
the company) any part which is defective in reasonable opinion of the Company. The user will have the
responsibility and expense of removing and returning the defective part to the Company as well as the
cost of reinstalling the replacement or repaired part.
IN NO EVENT SHALL THE COMPANY BE LIABLE FOR LOSS OF USE, LOSS OF REVENUE OR
LOSS OF PRODUCT OR PROFIT OR FOR INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING
BUT NOT LIMITED TO, FOOD SPOILAGE OR PRODUCT LOSS. WARRANTY DOES NOT COVER
GLASS BREAKAGE. THE ABOVE WARRANTY IS EXCLUSIVE AND ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, ARE EXCLUDED INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY SHALL
APPLY ONLY WITHIN THE CONTINENTAL UNITED STATES, ITS TERRITORIES, AND
POSSESSIONS AND IN CANADA.
LIMITED NINETY DAY LABOR WARRANTY
All labor necessary to repair or replace factory defective parts will be performed, without charge, to the
end user, by service personnel of a BKI Authorized Distributor during the first ninety days after the date of
installation of the new equipment.
Replacement parts: Any appliance replacement part, except lamps and fuses, which proves to be
defective in material or workmanship within 90 days from date of original installation will be repaired or
replaced without charge F.O.B. Factory, Simpsonville, S.C. or F.O.B. authorized distributor.
Electric Pressure Fryer
Table of Contents
Table of Contents
Table of Contents........................................................................................................................................ 1
Introduction ................................................................................................................................................. 2
Safety Precautions.................................................................................................................................... 2
Safety Signs and Messages................................................................................................................. 2
Specific Precautions ............................................................................................................................. 3
Safe Work Practices ............................................................................................................................. 3
Safety Labels........................................................................................................................................ 7
Installation ................................................................................................................................................... 8
Unpacking and Handling........................................................................................................................... 8
Assembly and Mounting ........................................................................................................................... 8
Wiring........................................................................................................................................................ 8
Initial Test and Adjustment ....................................................................................................................... 9
Maintenance .............................................................................................................................................. 10
Scheduled Maintenance ......................................................................................................................... 10
Safety Pop Valve Procedure .............................................................................................................. 11
Filtering Procedure ............................................................................................................................. 12
FKM-F and FKM-FC....................................................................................................................... 12
FKM................................................................................................................................................ 13
Boil-Out Procedure ............................................................................................................................. 14
Filter Pad Replacement...................................................................................................................... 16
Troubleshooting ...................................................................................................................................... 17
Replacement Parts.................................................................................................................................... 19
Assemblies.............................................................................................................................................. 19
Accessories............................................................................................................................................. 38
Components............................................................................................................................................ 39
Wiring Diagrams........................................................................................................................................ 41
1
Electric Pressure Fryer
Introduction
Introduction
The FKM Pressure Fryer is compact, attractive and functional in design. It is constructed of a stainless
steel fryer pot for cleaning ease. Exclusive BKI patented features and safety devices offer flexibility,
efficiency and reliability plus PERFECTION IN PRESSURE FRYING!
The BKI name and trademark on this unit assures you of the finest in design and engineering -- that it has
been built with care and dedication -- using the best materials available. Attention to the operating
instructions regarding proper installation, operation, and maintenance will result in long lasting
dependability to insure the highest profitable return on your investment.
PLEASE READ THIS ENTIRE MANUAL BEFORE OPERATING THE UNIT. If
you have any questions, please contact your BKI Distributor. If they are unable to
answer your questions, contact the BKI Technical Service Department, toll free:
1-800-927-6887. Outside the U.S., call 1-864-963-3471.
Safety Precautions
Always follow recommended safety precautions listed in this manual. Below is the safety alert symbol.
When you see this symbol on your equipment, be alert to the potential for personal injury or property
damage.
Safety Signs and Messages
The following Safety signs and messages are placed in this manual to provide instructions and identify
specific areas where potential hazards exist and special precautions should be taken. Know and
understand the meaning of these instructions, signs, and messages. Damage to the equipment, death or
serious injury to you or other persons may result if these messages are not followed.
This message indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
This message indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
This message indicates a potentially hazardous situation, which, if not avoided,
may result in minor or moderate injury. It may also be used to alert against
unsafe practices.
This message is used when special information, instructions or identification are
required relating to procedures, equipment, tools, capacities and other special
data.
2
Electric Pressure Fryer
Introduction
Specific Precautions
Lids for FKM Pressure Fryers manufactured prior to May 27, 1980 (or units with
serial numbers lower than 3613) could be manually opened while under pressure
resulting in serious injury or death. If you have one of these units, please contact
the BKI Technical Services Department toll-free at 1-800-927-6887 for urgent
update information.
Safe Work Practices
Noncombustible Floors Only
Make sure your floor is noncombustible. Do not operate your fryer
on floors that are wood, carpeted or have rubber mats.
•
Placing your fryer on a combustible floor could cause a fire.
Serious injury could result.
•
Examples of noncombustible floors where you can safely
place your fryer are concrete, tile, and ceramic.
Keep The Area Around Your Fryer Uncluttered
Make sure to keep the area around your fryer clear of any
obstacles.
Serious injury can occur if you trip or fall near the fryer. You could
be burned by hot shortening that splashes out of the fryer or by
falling against the hot metal of the fryer.
Keep The Floor Around Your Fryer Clean Of Shortening
Make sure to keep the floor around your fryer clean of shortening
and other liquids.
Serious injury can occur if you slip near your fryer. You could be
burned by hot shortening that splashes out of the fryer or by falling
against the hot metal of the fryer.
Keep The Lid Closed When The Fryer Is Not In Use
Hot shortening can splash if someone moves the fryer or bumps
into it. Serious injury can occur if hot shortening splashes out of the
fryer.
Do not lean, sit or stand on the fryer or perform any maintenance or
cleaning duties while the fryer or the shortening is hot. You could
be burned.
Keep The Casters Locked
To avoid spilling shortening, keep the casters locked. If any
shortening spills near your fryer, clean it up immediately.
3
Electric Pressure Fryer
Introduction
Do Not Overfill The Fryer With Shortening
Hot shortening and steam may escape and burn you if you put too
much shortening in the fryer. Fill the fryer to approximately one inch
below the fill marks that are inside the fryer pot. Heat the
shortening. If needed, carefully add more shortening to bring the
level to the fill marks.
Do Not Let Any Water Get Into The Fryer
Always remove excess moisture from food before placing it into the
fryer basket. Water will cause the hot shortening to spatter. You
could be burned.
Do Not Overload The Basket With Food
Hot shortening and steam may escape and burn you if you place
too much food in the basket.
Always Make Sure The Lid Hook Is Latched When Closing The
Fryer
To make sure the lid hook is latched properly, press down the lid
until the hook snaps shut. Hot shortening and steam can escape if
the lid hook is not latched properly. You could be burned.
Keep Away From The Vent
Hot steam escapes from the vent continuously when you are using
your fryer. You could be burned if you get too close to the vent.
Seal The Safety Valve Properly
To seal the safety valve, lift the arm on the side of the valve. Then
release it. The valve should snap closed. Hot steam can escape
from the valve and you could be burned if you do not seal the valve
properly.
Always Tighten The Spin Handle When Closing The Fryer
Hot shortening and steam can escape if you do not tighten the spin
handle properly. You could be burned. Line up the orange knobs on
the fryer lid handle and the front hook when tightening.
Do Not Over-Tighten The Spin Handle
You could damage the fryer.
4
Electric Pressure Fryer
Introduction
Wear Safe Clothing Appropriate To Your Job
Always wear your insulated mitts when handling the fryer basket or
touch any hot metal surfaces. You received a pair of insulated mitts
with your fryer. If you lose or damage your mitts, you can buy new
ones at your local restaurant equipment supply store or from your
local BKI Distributor.
Always wear non-skid shoes when working around the fryer or any
other equipment that uses shortening. Never wear loose clothing
such as neckties or scarves while operating your fryer. Keep loose
hair tied back or in a hair net while operating your fryer.
Always wear appropriate personal protection equipment during the
filtering process to guard against possible injury from hot oil.
Always wear appropriate personal protection equipment during the
boil-out process to guard against possible injury from hot cleaning
solution.
Never Loosen The Spin Handle Until The Pressure Gauge Is At
Zero
Steam may escape suddenly if you loosen the spin handle before
the gauge is at zero. If steam escapes suddenly, you could be
burned.
After the pressure gauge is at zero, wait 5 seconds. Then loosen
the spin handle slowly to open the lid of the fryer. By doing this, the
steam will escape slowly and there is less change of being burned.
Always use extreme caution when working around the fryer with the
lid open.
Keep this manual with the Equipment
This manual is an important part of your equipment. Always keep it
near for easy access.
If you need to replace this manual, contact:
BKI
Technical Services Department
P.O. Box 80400
Simpsonville, S.C. 29680-0400
Or call toll free: 1-800-927-6887
Outside the U.S., call 864-963-3471
Protect Children
Keep children away from this equipment. Children may not
understand that this equipment is dangerous for them and others.
NEVER allow children to play near or operate your equipment.
5
Electric Pressure Fryer
Introduction
Keep Safety Labels Clean and in Good Condition
Do not remove or cover any safety labels on your equipment. Keep
all safety labels clean and in good condition. Replace any damaged
or missing safety labels. Refer to the Safety Labels section for
illustration and location of safety labels on this unit.
If you need a new safety label, obtain the number of the specific
label illustrated on page 7, then contact:
BKI
Technical Services Department
P.O. Box 80400
Simpsonville, S.C. 29680-0400
Or call toll free: 1-800-927-6887
Outside the U.S., call 864-963-3471
Be Prepared for Emergencies
Be prepared for fires, injuries, or other emergencies.
Keep a first aid kit and a fire extinguisher near the equipment. You
must use a 40-pound Type BC fire extinguisher and keep it within
25 feet of your equipment.
Keep emergency numbers for doctors, ambulance services,
hospitals, and the fire department near your telephone.
Know your responsibilities as an Employer
• Make certain your employees know how to operate the
equipment.
• Make certain your employees are aware of the safety
precautions on the equipment and in this manual.
• Make certain that you have thoroughly trained your employees
about operating the equipment safely.
• Make certain the equipment is in proper working condition. If you
make unauthorized modifications to the equipment, you will
reduce the function and safety of the equipment.
6
Electric Pressure Fryer
Introduction
Safety Labels
7
Electric Pressure Fryer
Installation
Installation
Serious injury, equipment damage or death could result if attempting to install
this fryer yourself. Ensure that an authorized BKI service agent installs the fryer.
Unpacking and Handling
It is the owners’ responsibility to file all freight claims with the delivering truck line. Inspect all cartons and
crates for damage as soon as they arrive. If damage to cartons or crates is found, or if a shortage is
found, note this on the bill of lading (all copies) prior to signing.
If damage is found when the equipment is opened, immediately call the delivering truck line and follow up
the call with a written report indicating concealed damage to your shipment. Ask for an immediate
inspection of your concealed damage item. Packaging material MUST be retained to show the inspector
from the truck line.
Assembly and Mounting
1. Remove the shipping packing clip from underneath the dead weight cap and discard.
2. Replace the dead weight and cover.
3. If your fryer has casters, lock them so the fryer does not move.
4. Clean the fryer pot before filling with shortening.
5. Place the DRAIN handle in the CLOSED position
Wiring
Electrocution, equipment failure or property damage could result if an unlicensed
electrician performs the electrical installation. Ensure that a licensed electrician
performs the electrical installation.
The fryer, when installed by an authorized BKI service agent, must be wired in accordance with local
codes, or in the absence of local codes, with the National Electrical Code, ANSINFPA 70-2002. You can
obtain this code from:
The National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
8
Electric Pressure Fryer
Installation
Initial Test and Adjustment
1. Fill pot with shortening to about one inch below the mark.
Use only high-quality shortening that has low moisture content, a high smoke
point and no additives.
Overfilling the fryer pot with shortening could lead to serious injury. Ensure that
the fryer pot is filled with shortening only to the fill mark when shortening is hot.
Do not use any shortening other than what is specified in this manual and do not
overfill the fryer pot.
2. Place the FILTER/OFF/FRY switch to the FRY position. The shortening should begin to heat and
begin to reach the fill mark inside the pot. Add more shortening as required to reach the fill mark.
Refer to the troubleshooting section if this does not occur.
9
Electric Pressure Fryer
Maintenance
Maintenance
Failure to comply with the maintenance below could result in a serious accident.
Do not over-tighten the spindle assembly. (Only tighten to hold pressure.)
Your fryer will need periodic maintenance and servicing. We strongly suggest
that you use only a service company that is authorized by BKI to do this work.
Scheduled Maintenance
Use the following table to help manage scheduled maintenance activities.
FREQUENCY
Each Fry Cycle
Daily
Weekly
Every 6 Months
PERFORMED BY
PART
ACTIVITY
User
Pressure Gauge
Check for proper display of
cooking vat pressure. Contact
authorized BKI service agent if
adjustment or replacement is
required.
User
Lid Gasket
Check for unusual wear such
as cracks and deformation,
and pressure leaks. Contact
authorized BKI service agent if
adjustment or replacement is
required.
User
Dead Weight
Assembly
Clean weight and orifices daily
and check for wear.
User
Filter Pad
Replace filter pad. Refer to the
procedure in this manual.
User
Condensation
Pan
Remove and drain.
User
Filter system
Filter the shortening using the
procedure in this manual.
User
Safety Pop Valve
Check for release of pressure
and proper seal. Refer to the
procedure in this manual.
User
Fryer Pot
Perform the boil-out procedure
in this manual.
Authorized BKI
service agent
Acme Screw and
Nut
Check for wear on the threads.
Authorized BKI
service agent
Solenoid Valve
Check that the valve is holding
and releasing pressure when
the timer or computer activates
it.
Authorized BKI
service agent
Hook, Catch,
Spring
Check for wear and ease of
operation.
Authorized BKI
service agent
Connections,
Fittings
Check for leakage while oil is
pumping.
10
Electric Pressure Fryer
Maintenance
Safety Pop Valve Procedure
The safety pop valve should be blown under pressure periodically to prevent the seat from sticking.
Failure to use the insulated mitts will result in injury. Always use the insulated
mitts when handling the arm on the safety valve.
1. After the pressure is up during a cooking cycle, use the insulated glove to lift the arm on the edge
of the safety valve and let some steam escape. This will clean the valve.
2. Release the lever on the valve, and let it slam shut to seal the valve.
11
Electric Pressure Fryer
Maintenance
Filtering Procedure
Breaded foods require frequent filtering. An excess amount of breading left in the fryer pot will reduce the
life of the shortening. We recommend the shortening be filtered after every three frying cycle loads. When
the shortening starts to show signs of foaming and has a bad taste, do not use it. The fryer pot should be
cleaned before refilling with new shortening. Best results for filtering are obtained while the shortening is
hot. You should filter at the end of every business day. You should also remove and drain the
condensation pan daily.
Always wear appropriate personal protection equipment during the filtering
process to guard against possible injury from hot oil.
FKM-F and FKM-FC
1. Set the FILTER/OFF/FRY switch to OFF.
2. Remove the fryer basket.
3. Make certain that the filter pad is clean and not torn.
IMPORTANT: Make certain the vat cover is properly positioned underneath the drain valve.
Also make certain the filter vat and filter screen is under the main drain valve before starting
the filtering process.
4. Move the DRAIN handle slowly to the OPEN position so that the shortening starts to flow
evenly. This is to prevent excessive splashing of hot shortening.
5. When the pot is empty, place the DRAIN handle in the CLOSED position.
To refill the pot automatically, use the steps below:
Hot shortening may splash out of the pot causing severe injury when filling the
pot if the lid is not closed. To prevent shortening splashes, close the lid before
filling.
•
Close the lid to prevent shortening splashes.
•
Place the FILL handle to the THRU POT position.
•
Position the FILTER/OFF/FRY switch to FILTER and shortening will automatically pump
into the pot.
•
After 1 minute carefully open the lid to check the level of the shortening.
•
Let the filter continue to pump the shortening until the fill mark in the fryer pot is reached
or until air starts bubbling through the shortening.
•
As soon as air is seen in the shortening, first place the FILL handle to the THRU HOSE
position then position the FILTER/OFF/FRY switch to OFF to prevent shortening
degradation and prevent the filter pump and lines from filling up with shortening.
•
Add new shortening if the fill mark has not been reached.
12
Electric Pressure Fryer
Maintenance
To refill the pot through the rinse hose, use the steps below:
•
Make certain that the rinse hose is connected to rinse hose connector.
•
Holding the hose by the handle, place hose nozzle inside the pot.
Hot shortening may splash out of the pot causing severe injury when filling the
pot if the lid is not held down over the hose nozzle. To prevent shortening
splashes, hold the lid down over the hose nozzle.
•
Hold the lid down over the hose nozzle to prevent shortening splashes.
•
Position the FILL lever in the THRU HOSE position.
•
Position the FILTER/OFF/FRY switch to FILTER and shortening will automatically pump
into the pot.
•
After 1 minute, hold the hose by the handle and carefully raise the lid to check the level of
the shortening.
•
Let the filter continue to pump the shortening until the fill mark in the fryer pot is reached
or until air starts bubbling through the shortening.
•
As soon as air is seen in the shortening, position the FILTER/OFF/FRY switch to OFF to
prevent shortening degradation.
•
Add new shortening if the fill mark has not been reached.
FKM
1. Set the FILTER/OFF/FRY switch to OFF.
2. Remove the fryer basket.
3. Make certain that the FKF filter unit or portable filter unit filter pad is clean and not torn.
4. Position the FKF filter unit or portable filter unit under the main drain valve and make sure it’s
filter screen is in place.
5. Ensure that the FKF filter unit or portable filter unit is powered.
6. Move the DRAIN handle slowly to the OPEN position until the shortening starts to flow
evenly. This will prevent excessive splashing of hot shortening.
7. When the pot is empty, place the DRAIN handle in the CLOSED position.
To refill the pot through the drain valve, use the steps below:
•
Make certain that the braided hose (located on the drain valve) is connected to it’s mating
part on the FKF filter unit or portable filter unit.
Hot shortening may splash out of the pot causing severe injury when filling the
pot if the lid is not closed. To prevent shortening splashes, close the lid before
filling.
•
Close the lid to prevent shortening splashes.
13
Electric Pressure Fryer
Maintenance
•
Position the FILTER/OFF/FRY switch to FILTER and shortening will automatically pump
into the pot.
•
After 1 minute carefully open the lid to check the level of the shortening.
•
Let the filter continue to pump the shortening until the fill mark in the fryer pot is reached
or until air starts bubbling through the shortening.
•
As soon as air is seen in the shortening, position the FILTER/OFF/FRY switch to OFF to
prevent shortening degradation and prevent the filter pump and lines from filling up with
shortening.
•
Add new shortening if the fill mark has not been reached.
To refill the pot through the rinse hose, use the steps below:
•
Make certain that the rinse hose is connected to it’s mating part on the FKF filter unit or
portable filter unit.
•
Holding the hose by the handle, place hose nozzle inside the pot.
Hot shortening may splash out of the pot causing severe injury when filling the
pot if the lid is not held down over the hose nozzle. To prevent shortening
splashes, hold the lid down over the hose nozzle.
•
Hold the lid down over the hose nozzle to prevent shortening splashes.
•
Position the FILTER/OFF/FRY switch to FILTER and shortening will automatically pump
into the pot.
•
After 1 minute, hold the hose by the handle and carefully raise the lid to check the level of
the shortening.
•
Let the filter continue to pump the shortening until the fill mark in the fryer pot is reached
or until air starts bubbling through the shortening.
•
As soon as air is seen in the shortening, position the FILTER/OFF/FRY switch to OFF to
prevent shortening degradation.
•
Add new shortening if the fill mark has not been reached.
Boil-Out Procedure
Boil-outs remove microscopic particles of carbon that build up on the walls of the fryer pot. To avoid
eventual carbon build-up, off flavors, and shortening breakdown, boil-outs should be done once a week
on each fryer following these procedures.
Always wear appropriate personal protection equipment during the boil-out
process to guard against possible injury from hot cleaning solution.
1. Position the FILTER/OFF/FRY switch to OFF.
2. Drain the clean shortening into an adequate storage container. (Allow the shortening to cool to
room temperature before attempting storage.)
14
Electric Pressure Fryer
Maintenance
3. CLOSE the drain and fill the fryer pot with HOT water to the shortening level fill mark. Do not
overfill by allowing the water level higher than the fill mark.
4. Add ½ cup (4 ounces) of BKI cleaner.
5. Wash down the inside of the pot and lid with the pot brush to loosen the sediment.
6. Set the temperature of the solution as follows:
•
For an FKM or FKM-F – Position the FILTER/OFF/FRY switch to ON. Set the thermostat to
a temperature of 190º F.
•
For an FKM-FC – Position the FILTER/OFF/FRY switch to ON. Press PROG (program), type
1733, and press ENTER. The fryer pot will heat to a temperature of 190º F during the CLEAN
cycle to allow the CLEAN function to be performed. NOTE: The fryer pot must be below 255º
F to enter the CLEAN mode.
7. Bring the cleaning solution to a rolling boil and maintain the boil for 5 minutes.
8. Place the FILTER/OFF/FRY switch to OFF.
9. Scrub the inside of the fryer pot and inside of the lid again.
10. Before draining the cleaning solution, remove the filter bag, screen and pipe connections from
the filter vat. This must be done before draining the cleaning solution. NEVER pump water or
detergent through the filter system.
11. After 15 minutes, slowly open the drain valve. Drain the solution into the filter vat and discard.
12. Rinse the pot with hot water, using the pot brush to remove remaining sediment, drain and
discard.
13. Close the drain and refill the fryer pot with hot water to the proper level.
14. Add approximately 4 to 6 ounces of distilled (white) vinegar to develop a neutralizing solution. Stir
the solution briefly. Leave in the pot for three to five minutes and discard. NOTE: Foaming of
shortening after boil-outs is caused by failure to follow proper neutralizing procedures.
15. Repeat steps 12 through 14 as needed to remove all traces of cleaning solution.
16. Rinse the pot again with Cool water, drain and discard.
Damage to the fryer could result if the fryer pot is not completely dry before filling
with shortening. Refill the fryer pot with shortening ONLY when it is completely
dry.
17. Dry the fryer pot, lid, and filter vat COMPLETELY.
18. Close the main drain and fill with new shortening to the proper level.
15
Electric Pressure Fryer
Maintenance
Filter Pad Replacement
The filter pad must be replaced daily. If the shortening has a milky color when it is pumped into the pot,
the filter pad should be replaced immediately.
If the filter pad is not properly closed, breading crumbs will get through the pad
opening and clog the pump. Ensure that the filter pad is properly closed upon
replacement.
1. Place the filter screen inside the filter pad.
2. Fold the end of the pad and seal with the bag clip.
16
Electric Pressure Fryer
Maintenance
Troubleshooting
Refer to the table below for troubleshooting information.
Problem
Cause
Possible Solution
Pressure Loss or Not Releasing
Pressure
Dead Weight Valve Leaking
Clean the weight and orifice. If
problems persist, contact an
authorized BKI service agent for
corrective action.
Contact an authorized BKI
service agent for corrective
action.
After a period of time, it is
possible that the valve seat
and/or plunger may stick or wear.
Activate the valve by starting a
cook cycle. You should hear a
solid metallic CLICK sound from
the solenoid valve. If you should
hear no sound (or a slow
BUZZING CLICK), contact an
authorized BKI service agent for
corrective action.
Contact an authorized BKI
service agent for corrective
action.
Contact an authorized BKI
service agent for corrective
action.
Contact an authorized BKI
service agent for corrective
action.
Contact an authorized BKI
service agent for corrective
action.
Contact an authorized BKI
service agent for corrective
action.
Clean heating elements. If
problems persist, contact an
authorized BKI service agent for
corrective action.
Press the reset button on end of
pump and hi-limit reset button
under control panel. If problems
persist, contact an authorized
BKI service agent for corrective
action.
Tighten the connections. If
problems persist, contact an
authorized BKI service agent for
corrective action.
Lid Gasket Leaking
Solenoid Valve Leaking or
Stuck
Safety Valve not seating
Shortening Heating Too Slowly
Low voltage or improper
voltage
Bad thermostat or loose
wires
Weak heating elements or
heating elements breaking
down
Coil on contactor is bad
Breading build-up on heating
elements
Filter System Not Working
Uncertain
Connections not tight
17
Electric Pressure Fryer
Problem
Cause
Possible Solution
Filter valve not open
Contact an authorized BKI
service agent for corrective
action.
Change filter paper. If problems
persist, contact an authorized
BKI service agent for corrective
action.
Check for clogged pump. If
problems persist, contact an
authorized BKI service agent for
corrective action.
Contact an authorized BKI
service agent for corrective
action.
Make sure drain valve is
completely closed. If problems
persist, contact an authorized
BKI service agent for corrective
action.
Press and hold the Toggle/Clear
button while moving the
FRY/OFF/FILTER switch from
FRY to OFF and back to FRY. If
problems persist, contact an
authorized BKI service agent for
corrective action.
Filter paper on screen
clogged with crumbs
Motor hums, but does not
pump
Motor and pump coupling
worn
No power to control panel
Computer Hangs
Computer malfunction.
18
Electric Pressure Fryer
Replacement Parts
Replacement Parts
Use the information in this section to identify replacement parts. To order replacement parts, call your
local BKI sales and service representative. Before calling, please note the serial number, model number
and voltage on the rating tag affixed to the unit.
Assemblies
Description
Assembly #
Figure #
Table #
DEAD WEIGHT ASSEMBLY
AN19104100
Figure 1
Table 1
DOOR ASSEMBLY
SB1910
DRAIN/MOTOR/PIPING ASSEMBLY
N/A
Figure 3
Table 3
DRAIN VALVE & PLUGS
SB1999S
Figure 4
Table 4
DOMESTIC FRONT PANEL FKM/FKM-F
EUROPEAN FRONT PANEL FKM/FKM-F
AN19108100
AN19108200
Figure 5
Table 5
FRONT PANEL FKM-FC
AN19106400
Figure 6
Table 6
LID/TOP ASSEMBLY
SB1992S
Figure 7
Table 7
OIL VAT ASSEMBLY
AN16010200
Figure 8
Table 8
QUICK DISCONNECT ASSEMBLY
AN19103300
SB1997S
Figure 9
Table 9
DOMESTIC REAR PANEL FKM/FKM-F
EUROPEAN REAR PANEL FKM/FKM-F
AN19106100
AN19106500
Figure 10
Table 10
REAR PANEL FKM-FC
AN19106200
Figure 11
Table 11
SOLENOID VALVE
AN19104300
Figure 12
Table 12
19
Table 2
Figure 2
Electric Pressure Fryer
Replacement Parts
Figure 1. Dead Weight Assembly
Table 1. Dead Weight Assembly Parts
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PART #
FT0395
FT0396
O0001
O0002
PV0001
FT0066
FT0235
FT0190
FT0084
FT0563
FT0067
FT0234
C0657
B0969
W0201
G0064
QTY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DESCRIPTION
PIPE, POPOFF VALVE BAFF BOX
PIPE, DEAD WT TO BAFFLE BOX
ORIFICE, SS
GASKET, O-RING #2-222
VALVE, POP SAFETY 1321148
ELL, REDUCER 3/4 X 1/2 90 DEG
NIPPLE, 1/2 X C SS
ELL, STREET 1/4 90 DEG CP
COUPLING, BRASS 1/4
FITTING, COMPRESSION ¾”
BUSHING, C110JO 3/4 X 1/2 CP
NIPPLE, 1/4 X 1 1/2 SS 304
COVER, DEAD WEIGHT VALVE FKM
BODY, DEAD WEIGHT VALVE FKM
WEIGHT, VALVE FKM 12#
GAUGE, PRESSURE 30 PSI
20
Electric Pressure Fryer
Replacement Parts
Figure 2. Door Assembly
21
Electric Pressure Fryer
Replacement Parts
Table 2. Door Assembly Parts
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PART #
F0083
ST0013
H0010
N0059
N0165
N0527
N0175
N0176
P0022
RIV172
SB1951
SCR008
SCR383
WFKMA178
N0153
H0009
QTY
2
1
2
1
1
1
1
1
1
3
1
6
2
1
1
1
DESCRIPTION
THREAD INSERT 10-24 STEEL
BRACKET, BRUSH HOLDER FKM, LPF,LGF
HINGE, LH PIN HALF
DECAL, SMALL BRUSH/
DECAL, NOTICE LOST MANUAL
DECAL, SAFETY INSTR FRYERS
DECAL, SLIPPING ADMONITIONS
DECAL, INSTR & SAFETY MANUAL
HANDLE, PULL SS P60-1010
RIVET, 1/8 X 1/4 CS PLT POP
INSIDE DOOR POCKET/MAGNET WELD FKM
SCREW, 10 X 1/2 PHIL TRUSS HD
SCREW, 10-24 X 1/2" PHIL TRUSS HD
DOOR, FRYER OUTSIDE WELD
DECAL, FKM WARNING ACME SCREW
HINGE, DOOR,RH,PIN SIDE FRY.DOORS
22
Electric Pressure Fryer
Replacement Parts
Figure 3. Drain/Motor/Piping Assembly
23
Electric Pressure Fryer
Replacement Parts
Table 3. Drain/Motor/Piping Assembly Parts
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
PART #
MB19101000
FT0044
FT0412
SB1314
FT0538
FT0507
FT0536
FT0543
TU0206
TU0205
P0070
F0254
F0255
F0253
SP0014
SP0034
NUT253
F0158
LZ0130
S0054
H0089
N0285
SCR194
H0215
C0672
SCR006
MA19100508
C0668
P0081
B0851
MA19100800
FT0132
M0053
QTY
1
1
2
1
1
1
3
1
1
1
1
2
1
1
2
2
2
1
1
1
1
1
2
1
1
3
1
1
1
1
1
1
1
DESCRIPTION
DRAIN VALVE REPLACEMENT
ELL, STREET 3/8 90 DEG BLACK
NIPPLE, 3/8 NPT X 1 1/2 SCH 40
BALL VALVE ASSY, FRYERS
TEE, 1/2 X 1/2 X 3/8 BLK
CONNECTOR, MALE 10FBU-S NKL PLTD
COUPLING, 5/8 45¦ FLARE TO
DRAIN VALVE BRACKET, FRYERS
TUBING, 29" 1/2" ID
TUBING, 12" 1/2" ID
PUMP ONLY FOR HAIGHT MOTOR
PIN, COTTER HAIRPIN #213
PIN, CLEVIS 3/16 X 1-1/4
PIN, CLEVIS 3/16 X 1 3/4
SPACER, ALUM .5 X .125
SPACER, DRAIN VALVE BRKT FRYERS
NUT, 6-32 S/S 18-8 NYLON
BUSHING, BLK 1/2 HEYCO SNAP
SWITCH,ACT. COVER FKMA247
SWITCH, MICRO BZ-2RW822-A2
HANDLE SUPPORT PLATE
DECAL, FKM-F DRAIN HNDL PLATE
SCREW, 6-32 X 1 SL RD HD MS
HANDLE, DRAIN VALVE FKM BLF
COVER, DRAIN HANDLE RED
SCREW, 8 X 1/2 PHIL PAN HEAD
FILL VALVE HANDLE, FRYERS
COVER, FILL HANDLE BLACK
PLUG, F-H4F4-7-7 QUIK DISCONN
BUSHING, BLK HEX REDUCING
TUBING, TEE TO DISCONNECT
ELL, STREET 1/2 90 DEG BLACK
MOTOR, LEESON LESS CORD/PUMP
24
Electric Pressure Fryer
Replacement Parts
Figure 4. Drain Valve & Plugs
Table 4. Drain Valve & Plugs Parts
ITEM #
1
2
PART #
MB19101000
FT0243
QTY
1
2
DESCRIPTION
DRAIN VALVE REPLACEMENT
PLUG, 3/8" SQ HEAD PIPE
25
Electric Pressure Fryer
Replacement Parts
Figure 5. Domestic/European Front Panel FKM/FKM-F
Table 5. Domestic/European Front Panel FKM/FKM-F Parts
ITEM #
1
2
3
4
5
6
PART #
N0522
S0104
TI0032
PL0004
T0075
K0040
QTY
1
1
1
1
1
1
DESCRIPTION
DECAL, CTL PNL FKM FKMF
SWITCH, RKR DPDT 15A 250V LAMP
TIMER, 230V DIGITAL 4 BUTTON
PILOT LIGHT, ROUND 250V
THERMOSTAT, SOLID STATE FRYER
KNOB, S/S STRAT T0075
26
Electric Pressure Fryer
Replacement Parts
Figure 6. Front Panel FKM-FC
Table 6. Front Panel FKM-FC Domestic Parts
ITEM #
1
2
3
PART #
N0524
S0104
CP0039
QTY
1
1
1
DESCRIPTION
DECAL,CTL PNL FKMFC
SWITCH, RKR DPDT 15A 250V LAMP
CONTROLLER, VFD LESS HARNESS
27
Electric Pressure Fryer
Replacement Parts
Figure 7. Lid/Top (sheet 1 of 4)
28
Electric Pressure Fryer
Replacement Parts
Figure 7. Lid/Top (Sheet 2 of 4)
29
Electric Pressure Fryer
Replacement Parts
Figure 7. Lid/Top (Sheet 3 of 4)
30
Electric Pressure Fryer
Replacement Parts
Figure 7. Lid/Top (Sheet 4 of 4)
31
Electric Pressure Fryer
Replacement Parts
Table 7. Lid/Top Parts
ITEM #
Figure 7 (sheet 1)
Figure 7 (sheet 2)
1
2
3
4
Figure 7 (sheet 3)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Figure 7 (sheet 4)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
PART #
SB1992S
SB3481
FT0332
K0003
K0020
K0043
AB19103900
A0120
H0155
P0094
H0024
K0043
N0160
NUT128
S0091
SCR122
SCR259
TB0020
H0156
WSH045
WSH102
FT0407
F0026
SB1989
F0353
G0016
S0155
B0857
P0115
FK0010
C0674
F0107
FKMA016
FKMA152
FKMA201
FT0049
N0153
N0345
SCR383
SCR176
SCR178
TB0021
TC0003
TC0005
TS0010
S0071
LZ0107
QTY
1
3
2
1
1
1
1
1
1
1
1
1
2
1
2
2
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
2
1
1
1
1
1
1
1
DESCRIPTION
LID/TOP
HANDLE ASSY, SPIN
STUD, 5.5” TIGHTEN DN HN
KNOB, BLACK #85C
HUB, TIGHTEN DOWN
KNOB, ORANGE
ARM ASSY, FKM
ARM COMPLETE FKM LGF
HANDLE, BLK DELRIN FKM LPF LGF
PIN, HOOK FKM, LPF, LGF
HOOK, LID 1018 ALLOY
KNOB, ORANGE
DECAL, WARNING BEFORE USING
NUT, 5/16-18 SS 18-8 CAP
SPRING, HOOK LGF LPF FKM
SCREW, 1/4-20 X 1/2 FLAT HD
SCREW, 1/4-20 X 1/2 PHIL RD HD
BUSHING, BRONZE 1"
HANDLE SIDE FOR H0155 FKM LPF LGF
WASHER, 5/16 LOCK ZINC PLTD
WASHER, 1/4 INT LOCK
PLUG, HOLE 3/8" SHORT PRONG
ROLL PIN, 5/32 X 3/4
LID LOCKING ASSY W/INSERT FKM
PIN, LOCKING FKM LGF LPF
GASKET, FKM LID BONDED SILICON
SPRING, LOCKING PIN W/LID INSERT
BUSHING, BRONZE 3/8X9/16X5/8
LID INSERT, FKM
LID, FKM CAST ALUM
LID COVER AND ARM GUIDE FKM
LOCK KEY PIN, FRYERS
PIN, HINGE
KEY, TIGHTEN DOWN SCREW
PLATE, TIGHTEN DOWN FKM
COLLAR, 1/2" SET BRIGHT
DECAL, FKM WARNING ACME SCREW
DECAL, HOOK LID INSTRUCTIONS
SCREW, 10-24 X 1/2" PHIL TRUSS HD
SCREW, 8-32 X 3/8 SLOT BINDING
SCREW, 5/16-18 X 1 FLAT HD
TIGHTEN DOWN BASE COLD ROLLED
COLLAR, THREADED SHAFT
COLLAR, LOCKING RING
SCREW, TIGHTEN DOWN
SPRING, TORSION
PLATE, LID FOR LOCKING DEVICE
32
Electric Pressure Fryer
Replacement Parts
Figure 8. Oil Vat Assembly
33
Electric Pressure Fryer
Replacement Parts
Table 8. Oil Vat Assembly Parts
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
PART #
SB1991
O0013
WB16010600
WB16010400
SB7659
FS0003
FS0002
FS0001
FKMA357
FC0004
N0395
SB7675
QTY
1
1
1
1
1
1
1
1
1
1
1
1
DESCRIPTION
QUIK DISCONNECT BRACKET WELDMENT
O-RING, FLUOROCARBON V680-70
FILTER VAT WELD QUIK DISC
FILTER VAT TUBE WELD, BLF
FILTER SCREEN FITTING SPOTWELD
FILTER SCREEN, TOP
FILTER SCREEN, INTERCEPTOR
FILTER SCREEN, BOTTOM
COVER, FILTER VAT
NUT SCREEN RETAINING FKM-F &
DECAL, VAT COVER SAFETY WARN
CRUMB BASKET WELD, LG VAT ASSY
Figure 9. Quick Disconnect Assembly
Table 9. Quick Disconnect Assembly Parts
ITEM #
1
2
3
4
5
6
7
8
PART #
B0996
FT0429
FT0500
FT0536*
O0013
O0014
S0138
SCR4531*
QTY
1
1
1
1
2
1
1
2
DESCRIPTION
BALL, 11/16" STEEL BEARING
QUICK DISCONNECT, PUMP SIDE
QUICK DISCONNECT, VAT SIDE
COUPLING, 5/8 45¦ FLARE TO
O-RING, FLUOROCARBON V680-70
O-RING, PARKER #2-124 LARGE
SPRING, FOR QUICK DISCONNECT
SCREW, #10 24X3/8" WASHERED
* - Not included with SB1997S
34
Electric Pressure Fryer
Replacement Parts
Figure 10. Domestic/European Rear Panel FKM/FKM-F
Table 10. Domestic/European Rear Panel FKM/FKM-F Parts
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PART #
T0036
TB0064
TB0065
TB0068
TB0069
R0148
F0158
F0097
R0134
F0154
F0342
FH0001
FT0080
FT0277
QTY
1
1
2
1
1
1
1
2
3
2
3
2
1
1
DESCRIPTION
THERMOSTAT, HI LIMIT 540 DEG
TERM BLOCK 4 CONDUCTOR CTR
TERM BLOCK 4 CONDUCTOR W/MTG FOOT
TERM BLOCK END PLATE
TERM BLOCK JUMPER BAR (not shown)
RELAY, 3 POLE 42CF35AG
BUSHING, BLK 1/2 HEYCO SNAP
FUSE, 15A 300V SC15 TIME DELAY
RELAY, MERCURY MDI 60NO220A
BUSHING, BLK 1-3/16 HEYCO SNAP
CLAMP, CABLE 3/16"
FUSE HOLDER, 15A 300V HPF-EE
CONNECTOR, BOX #7483 1"
PLUG, HOLE 7/8" (1/2" CONDUIT)
35
Electric Pressure Fryer
Replacement Parts
Figure 11. Rear Panel FKM-FC
Table 11. Rear Panel FKM-FC Parts
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PART #
T0036
R0148
TB0064
TB0065
TB0068
R0134
W0054
TB0069
F0154
R0044
F0097
F0158
F0342
FH0001
FT0080
FT0277
QTY
1
1
1
2
1
3
1
1
2
2
2
1
3
2
1
1
DESCRIPTION
THERMOSTAT, HI LIMIT 540 DEG
RELAY, 3 POLE 42CF35AG
TERM BLOCK 4 CONDUCTOR CTR
TERM BLOCK 4 CONDUCTOR W/MTG FOOT
TERM BLOCK END PLATE
RELAY, MERCURY MDI 60NO220A
TRANSFORMER ASSY 240V
TERM BLOCK JUMPER BAR (not shown)
BUSHING, BLK 1-3/16 HEYCO SNAP
RELAY, X-40, SGL FRYER
FUSE, 15A 300V SC15 TIME DELAY
BUSHING, BLK 1/2 HEYCO SNAP
CLAMP, CABLE 3/16"
FUSE HOLDER, 15A 300V HPF-EE
CONNECTOR, BOX #7483 1"
PLUG, HOLE 7/8" (1/2" CONDUIT)
36
Electric Pressure Fryer
Replacement Parts
Figure 12. Solenoid Valve Assembly
Table 12. Solenoid Valve Assembly Parts
ITEM #
1
2
3
4
PART #
FT0249
FT0396
SV0001
FT0563
QTY
1
1
1
1
DESCRIPTION
CONNECTOR, 3/8 STR FLEX LIQUIDTITE
PIPE, DEAD WT TO BAFFLE BOX
VALVE, SOLENOID HV-214-761-2 240V
FITTING, COMPRESSION ¾”
37
Electric Pressure Fryer
Replacement Parts
Accessories
Description
BASKET, LARGE FKM BAIL HANDLE
BRUSH, DRAIN (LONG WHITE)
BRUSH, L TIPPED 40152
BRUSH, LONG #5702
BRUSH, POT SCRUBBER, WHITE
BRUSH, SHORT #6175
CORD SET, FKM-FC 7'
FILTER HOSE, FEMALE SOCKET
FILTER VAT DOLLY FKM-F
INSULATED MITT 13"
Accessory #
B0114
B0075
B0063
B0051
B0049
B0052
SB7655
SB2332
SB7650
G0052
Figure #
Figure 13
Figure 13
Figure 13
Figure 13
Figure 13
Figure 13
Figure 13
Figure 13
Figure 13
Figure 13
Figure 13. Accessories
1
2
3
4
5
6
7
8
9
10
38
Item #
1
2
3
4
5
6
7
8
9
10
Electric Pressure Fryer
Replacement Parts
Components
Description
ARM ADJUSTABLE STOP /FKM
BAFFLE BOX ASSEMBLY
BRACKET, CALROD FKMA258
CALROD, 208V 5675W FKM-F
CALROD, 240V 5675W FKM-F
CASTER, W/TOP PLATE 5"
CLAMP, HOSE #6207 #4
COLLAR, 1/2" SET BRIGHT
CONDENSATION PAN WELDMENT
DRAIN PIPE, CONDENSATE FKM
FILTER, FKM-F 13.5 X 20.5
OUTLET BOX, (ON FKM ONLY FOR POWERING FKF)
PROBE ASSEMBLY KIT, COMPUTER
SEMI AUTOMATIC HOSE ASSEMBLY (FKM only)
SIDE CABINET, L&R FKM/DNF
SLIDE, UHMW U-SHAPE .5 X 1/8ID
STRIKER PLATE (DOOR CATCH)
SWITCH, ACT. COVER FKMA247
THERMISTER PROBE/FTGS ASSEMBLY
BRACKET BACK PLATE FKMA259
FILTER BAG CLIP FKM-F
Component #
A0101
AN19102800
LZ0006
C0030
C0031
C0406
HF0009
FT0049
WFKMA341
FKMA260
FI0007
SB1953
SB1938
SB1990
FKMA399
S0106
FKMA167
LZ0130
SB7656
LZ0007
ST0015
Figure 14. Components
1
2
3
4
5
6
39
Figure #
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Figure 14
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Electric Pressure Fryer
Replacement Parts
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
40
Electric Pressure Fryer
Wiring Diagrams
Wiring Diagrams
Refer to the table below to find the wiring diagram associated with your unit.
Wiring Diagram
Figure #
Page #
Domestic FKM & FKM-F 208V/220V/240V
Figure 15
42
European FKM & FKM-F 220V/380V, 230V/400V, 240V/415V
Figure 16
46
FKM-FC 208V/220V/240V
Figure 17
50
FKM-FC 220V/380V, 230V/400V, 240V/415V
Figure 18
54
41
Electric Pressure Fryer
Wiring Diagrams
Figure 15. Domestic FKM & FKM-F 208V/220V/240V (Sheet 1 of 4)
42
Electric Pressure Fryer
Wiring Diagrams
Figure 15. Domestic FKM & FKM-F 208V/220V/240V (Sheet 2 of 4)
43
Electric Pressure Fryer
Wiring Diagrams
Figure 15. Domestic FKM & FKM-F 208V/220V/240V (Sheet 3 of 4)
44
Electric Pressure Fryer
Wiring Diagrams
Figure 15. Domestic FKM & FKM-F 208V/220V/240V (Sheet 4 of 4)
45
Electric Pressure Fryer
Wiring Diagrams
Figure 16. European FKM & FKM-F 220V/380V, 230V/400V, 240V/415V (Sheet 1 of 4)
46
Electric Pressure Fryer
Wiring Diagrams
Figure 16. European FKM & FKM-F 220V/380V, 230V/400V, 240V/415V (Sheet 2 of 4)
47
Electric Pressure Fryer
Wiring Diagrams
Figure 16. European FKM & FKM-F 220V/380V, 230V/400V, 240V/415V (Sheet 3 of 4)
48
Electric Pressure Fryer
Wiring Diagrams
Figure 16. European FKM & FKM-F 220V/380V, 230V/400V, 240V/415V (Sheet 4 of 4)
49
Electric Pressure Fryer
Wiring Diagrams
Figure 17. FKM-FC 208V/220V/240V (Sheet 1 of 4)
50
Electric Pressure Fryer
Wiring Diagrams
Figure 17. FKM-FC 208V/220V/240V (Sheet 2 of 4)
51
Electric Pressure Fryer
Wiring Diagrams
Figure 17. FKM-FC 208V/220V/240V (Sheet 3 of 4)
52
Electric Pressure Fryer
Wiring Diagrams
Figure 17. FKM-FC 208V/220V/240V (Sheet 4 of 4)
53
Electric Pressure Fryer
Wiring Diagrams
Figure 18. FKM-FC 220V/380V, 230V/400V, 240V/415V (Sheet 1 of 4)
54
Electric Pressure Fryer
Wiring Diagrams
Figure 18. FKM-FC 220V/380V, 230V/400V, 240V/415V (Sheet 2 of 4)
55
Electric Pressure Fryer
Wiring Diagrams
Figure 18. FKM-FC 220V/380V, 230V/400V, 240V/415V (Sheet 3 of 4)
56
Electric Pressure Fryer
Wiring Diagrams
Figure 18. FKM-FC 220V/380V, 230V/400V, 240V/415V (Sheet 4 of 4)
57
P.O. Box 80400, Simpsonville, S.C. 29680-0400, USA
http://www.bkideas.com
Made and printed in the U.S.A
LI0192/0504
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement