FCD-IP - ITM Group

FCD-IP - ITM Group
Where to buy
>
See the product page >
Data Sheet
FCD-IP
E1/T1 or Fractional E1/T1 Access Unit with Integrated Router
Integrated access
device providing
bundled services
over E1/T1 access
lines
• Provides bundled services (data, IP, and telephony) over E1/T1 access lines
• E1/T1 uplink over copper or fiber optic media
• Operates opposite RAD's DXC cross-connect system and Megaplex access
multiplexers
• Supports Frame Relay, PPP, and MLPPP
FCD-IP is an E1/T1 or fractional E1/T1
integrated access device (IAD), which
enables service providers to bundle data,
voice, and IP access services over a single
E1 or T1 access line (see Figure 1).
Supported WAN services are:
•
T1 or fractional T1 CSU/DSU operating
at rates of up to 1.544 Mbps
•
E1 or fractional E1, with or without
LTU, operating at rates of up to 2.048
Mbps
•
E1 or T1 over fiber optic links
•
Frame Relay with auto-learn of DLCI
and maintenance protocol
•
ISDN BRI (“U” or “S” interface) for
data services backup.
The Access Company
FCD-IP
E1/T1 or Fractional E1/T1 Access Unit with Integrated Router
An integrated router supports IP routing
and transparent bridging.
•
Single IP address translation that
allows a small or medium office LAN to
connect to the Internet using a single
dynamically or statically allocated IP
address
•
DHCP server that allows the sharing of
ISP address pools between DHCP
clients on the LAN.
•
OSPF protocol based on the link state
technology, distributing information
about the state of links between
routers.
An optional internal 4-port Ethernet/Fast
Ethernet switch can be installed in place
of LAN ports.
Internet/intranet access capabilities are
enhanced through:
•
IP Service Access authentication
provided by PAP/CHAP
•
Solid Firewall that protects an office
LAN from undesired entry from the
Internet
•
NAT that allows the sharing of several
legal IP addresses between the various
LAN users
The sub-E1/T1 or quad analog voice
drop-and-insert ports provide toll-quality
voice transmission. Up to three sub-E1/T1
ports can be installed in FCD-IP,
aggregating three fractional E1s into one
full E1 stream (see Figure 2).
In the ring (Figure 3) and daisy-chain and
shared LAN applications (Figure 4), the
first sub-E1/T1 port (sub1-E1/T1) can be
used as a main link. In this case some of
the E1/T1 timeslots pass through internal
routers of all FCD-IP devices used in the
application. The other timeslots are
dropped at the user interfaces (FXS,
remaining sub-E1/T1 ports etc). This
enables the units to drop and insert
timeslots and take routing decisions at
any FCD-IP.
Notes: The sub1-E1/T1 port cannot be defined as a
main link if FCD-IP includes a DTE data port, two
LAN ports or ISDN ports.
FCD-IP connected to two LANs cannot be used in
the ring applications.
The fail-safe bypass of the sub1-E1/T1 link
ensures the continuity of voice services in
case of power supply failures. The bypass
is not available for the fiber optic main
links.
ISDN or PSTN backup, using an external
dial-up modem, ensures the continuity of
data services.
Figure 1. Bundled Services
Data Sheet
An optional data port can be utilized
either as a second serial router port or as
a transparent n × 64, n × 56 data port for
connecting legacy equipment.
The dual-level management authentication
allows user access to router configuration
parameters, while restricting user access
to network configuration parameters.
The unit can be easily configured through
a quick setup menu using a terminal
attached to the control port or by Telnet
access over the LAN/WAN.
Software download is available via the
control port using XMODEM and via
LAN/WAN using TFTP.
FCD-IP features a variety of inband and
out-of-band management options. These
options include dedicated timeslot,
dedicated DLCI and dial-in.
Parameter file download and upload is
available via LAN or WAN using TFTP.
The SNMP agent provides management by
RADview or any other standard SNMP
management station.
Undesired access to FCD-IP via Telnet or
SNMP can be blocked or password
protected.
Figure 2. Aggregating Three Fractional E1 Links into One Full E1 Link
FCD-IP
E1/T1 or Fractional E1/T1 Access Unit with Integrated Router
Specifications
E1 INTERFACE
Framing
G732N (no MF, CCS)
G732N (no MF, CCS) with CRC-4
G732S (TS16 MF, CAS)
G732S (TS16 MF CAS) with CRC-4
Bit Rate
2.048 Mbps
Line Code
AMI
Zero Suppression
HDB3
Impedance
120Ω, balanced
75Ω, unbalanced
Signal Level
Receive:
0 to -36 dB with LTU
0 to -12 dB without LTU
Transmit:
3V (±10%), balanced
2.37V (±10%), unbalanced
Jitter Performance
As per ITU G.823
Connectors
RJ-45, balanced or two BNC coaxial,
unbalanced (via adapter cable)
Compliance
ITU G.703, G.704, G.706, G.732
Diagnostics
User-activated local and remote loopbacks
T1 INTERFACE
ANALOG VOICE INTERFACE
Framing
D4, ESF
Number of Channels
Four
Bit Rate
1.544 Mbps
Modulation Method
PCM (per ITU-T G.711 and
AT&T PUB-43801), μ-Law or A-Law
Line Code
AMI
Zero Suppression
Transparent, B7ZS, B8ZS
Impedance
100Ω, balanced
Signal Level
Receive:
0 to -36 dB with CSU
0 to -15 dB without CSU
Transmit:
0, -7.5, -15, -22.5 dB with CSU
Soft adjustable at 0 to 655 ft, without
CSU
Jitter Performance
As per AT&T TR-62411
Connector
RJ-45 8-pin, balanced
Compliance
AT&T TR62411, ANSI T1.403
Diagnostics
User activated local and remote loopbacks
Network activated loopbacks and FDL
loopbacks (RLB, LLB)
Data Sheet
INTERFACES
DIAGNOSTICS
E&M:
2-wire or 4-wire, supporting different
types of E&M signaling: RS-464 Types
I, II, III and V, and BT SSDC5,
software-configured
Local digital loopback towards the analog
side
Remote analog loopback towards the
remote side, activated from the local
side
1 kHz tone injection towards the analog
side
FXS:
Loop start, WINK start (reverse
polarity) for direct connection to a
2-wire telephone, CID (Caller ID)
support
Connectors
E&M: RJ-45, 8-pin
FXS, FXO: RJ-11, 6-pin
FXO:
Loop start, WINK start (reverse
polarity) connection to a 2-wire
telephone exchange subscriber line
ISDN INTERFACE
Interface
ISDN BRI, “S” and “U”
Nominal level: 0 dBm
Compliance
ETS 300012, I.430, NTT, 5ESS, DMS-100,
NI1
Nominal impedance: 600Ω
Return loss: (ERL), better than 20 dB
Frequency response (Ref: 1020 Hz):
±0.5 dB, 300 to 3000 Hz
±1.1 dB, 250 to 3400 Hz
Signal to total distortion, G.712, G.713
method 2:
0 to -30 dBm0, better than 33 dB
+3 to -45 dBm0, better than 22 dB
Idle channel noise: Better than
-70 dBm0 (+20 dBrnc)
Transformer isolation: 1500 VRMS
Table 1. Fiber Optic Interface Characteristics
Wavelength
Fiber Type
[nm]
[μm]
850
62.5/125
multimode
9/125 single
mode
9/125 single
mode
1310
1550
Transmitter
Type
Power
[dBm]
Receiver
Sensitivity
[dBm]
Typical Max.
Range
[km]
[miles]
VCSEL
-18
-38
5
3
Laser
-12
-39
62
38
Laser
-12
-39
100
62
FCD-IP
E1/T1 or Fractional E1/T1 Access Unit with Integrated Router
LAN INTERFACE
FIBER OPTIC INTERFACE
GENERAL
Number of Ports
1, 2, or 4
Types
See Table 1
Compliance
Compliance
ITU G.921, G.955 (11/1996)
Power
AC: 100 to 240 VAC (±10%), 50 to 60 Hz,
13 VA max
DC: -24 to -48 VDC, 13W
IEEE 802.3
Type
Single 10/100BaseT (RJ-45) port
Dual 10BaseT (RJ-45)
4-port 10/100BaseT (RJ-45) switch
WAN PROTOCOLS
Type
Frame Relay - RFC 1490
PPP and MLPPP
DATA PORT INTERFACE
Type and Connectors
RS-232/V.24 or RS-530 with 25-pin
D-type, female
RS-422/V.36 with 37-pin D-type, female
V.35 with 34-pin female
X.21 with 15-pin D-type, female
ROUTING
Types
STATIC, RIP-I, RIP-2, RIP/SAP, OSPF
ARP Table
Up to 300 MAC addresses
Note: All synchronous data ports are equipped
with 25-pin D-type, female connectors. Adaptor
cables for the V.35, V.36 and X.21 interfaces are
supplied with the unit.
Figure 3. FCD-IP in an E1 Ring Topology
Physical
Height: 4.4 cm (1.8 in) (1U)
Width: 21.6 cm (8.5 in)
Depth: 24.0 cm (9.4 in)
Weight: 1.1 kg (2.5 lb)
Environment
Temperature: 0°C to 50°C (32°F to 122°F)
Humidity: Up to 90%, non-condensing
Data Sheet
Ordering
#
STANDARD CONFIGURATIONS
FCD-IP/DC/E1/U/S
FCD-IP/E1/U
FCD-IP/DC/E1/FC13L/U/E&M
FCD-IP/E1/4U/FXS
FCD-IP/E1/U/S
SPECIAL CONFIGURATIONS
FCD-IP/~/$/+/*
E1/T1 or fractional E1/T1 access unit with
integrated router
Optional second WAN interface:
V24T V.24/RS-232 (DTE)
V35T V.35 (DTE)
530T RS-530 (DTE)
V36T V.36/RS-422/RS-449 (DTE)
X21T X.21 (DTE)
or
Serial port interface:
V24C V.24/RS-232 (DCE)
V35C V.35 (DCE)
530C RS-530 (DCE)
V36C V.36/RS-422/RS-449 (DCE)
X21C X.21 (DCE)
Note: All synchronous data ports are equipped
Legend
with 25-pin D-type, female connectors. Adapter
~
cables for the V.35, V.36, and X.21 interfaces are
DC power supply (Default=AC power
supply):
DC
-20 to -72 VDC
supplied with the unit.
?
Note: FCD-IP with FXS, FXO and E&M voice
interfaces cannot work with -24 VDC voltage
within the DC power supply range.
$
Primary WAN interface with optional
second data port:
E1/#
E1 or fractional E1 (RJ-45
only)
T1/#
T1 or fractional T1
E1/?/!/# E1 or fractional E1 with
built-in fiber optic modem
T1/?/!/# T1 or fractional T1 with
built-in fiber optic modem
Note: The T1 line cannot be used for a ring
application.
!
+
Fiber optic connector:
ST ST connector
FC FC/PC connector
SC SC connector
Wavelength and type:
85 850 nm, multimode, VCSEL
13L 1310 nm, single mode laser
diode
15L 1550 nm, single mode laser
diode
LAN
U
2U
4U
interface:
10/100BaseT (UTP)
2 × 10BaseT (UTP)
4 × 10/100BaseT (UTP) built-in
switch
Figure 4. Daisy-Chain and Shared LAN Topology
*
Optional sub-E1/T1, analog voice or
ISDN backup interfaces:
S
sub-E1/T1 port (RJ-45 only)
2S
2 sub-E1/T1 ports (RJ-45 only)
3S
3 sub-E1/T1 ports (RJ-45 only)
FXS
4 FXS voice channels
FXO
4 FXO voice channels
E&M
4 E&M voice channels
IBE
ISDN “S” interface
IBU
ISDN “U” interface
FXS/S 4 FXS voice channels and one
sub-E1/T1 port
FXO/S 4 FXO voice channels and one
sub-E1/T1 port
E&M/S 4 E&M voice channels and
one sub-E1/T1 port
IBE/S ISDN “S” interface and one
sub-E1/T1 port
IBU/S ISDN “U” interface and one
sub-E1/T1 port
Notes: 1. The second WAN option is not available
when configuring E1/T1 with an ISDN backup.
2. The dual LAN configuration is not available when
configuring E1/T1 with an ISDN backup.
3. The line cannot be fiber for options 3S, FXS/S,
FXO/S, E&M/S, IBE/S, or IBU/S.
4. 3S (3 sub-E1/T1 ports) cannot be installed with
an additional FXO, FXS, E&M, IBE, or IBU.
Data Sheet
FCD-IP
E1/T1 or Fractional E1/T1 Access Unit with Integrated Router
Power cord
DC power connection kit (when DC power
supply is ordered)
CBL-RJ45/D9/F/6FT
Control port cable
When V.35, V.36, or X.21 interfaces are
ordered, adaptor cables are supplied with
the unit.
OPTIONAL ACCESSORIES
CBL-RJ45/2BNC/E1
Interface cable for converting a balanced
E1 RJ-45 connector into a pair of BNC
unbalanced coaxial connectors
RM-17
Hardware kit for mounting one or two
FCD-IP units into a 19-inch rack
Table 1. Comparison Table
Features
FCD-IP
FCD-IPM
Total user ports
Up to 11
Up to 19
Interface types
X.21, V.35, V.24, RS-530, E1/T1, E&M, FXS,
FXO, ISDN, SHDSL, ETH
X.21, V.35, V.24, RS-530, E1/T1, E&M, FXS,
FXO, ISDN, SHDSL, ETH
E1/T1 line type
9
9
SNMP management
9
9
Interoperability
9
9
E1 bypass
9
9
ETH performance
10/100 MB/s
10/100 MB/s
International Headquarters
24 Raoul Wallenberg Street
Tel Aviv 69719, Israel
Tel. 972-3-6458181
Fax 972-3-6498250, 6474436
E-mail [email protected]
www.rad.com
North America Headquarters
900 Corporate Drive
Mahwah, NJ 07430, USA
Tel. 201-5291100
Toll free 1-800-4447234
Fax 201-5295777
E-mail [email protected]
Order this publication by Catalog No. 801764
The Access Company
676-100-06/11 (4.2) Specifications are subject to change without prior notice. © 1991–2011 RAD Data Communications Ltd. The RAD name, logo, logotype, and the terms EtherAccess, TDMoIP and TDMoIP Driven,
and the product names Optimux and IPmux, are registered trademarks of RAD Data Communications Ltd. All other trademarks are the property of their respective holders.
SUPPLIED ACCESSORIES
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement