FUSSION 3000

FUSSION 3000
Fussion Series
3-Way Active Speaker System
SPEAKER
FUSSION 3000
■ Mackie’s FUSSION 3000 is a high-output, 3-way, mediumthrow, active speaker system. It features high-precision trans-
FUSSION 3000
ducers combined with application-specific amplifier technology that allows this integrated system to generate high output
levels with very low distortion characteristics.
■ FUSSION 3000 transducers include a special, low inductance, double voice-coil 8-inch, horn-loaded (80˚ x 70˚ )
midrange transducer designed to deliver the lowest possible
distortion even at full power. It operates between 500Hz and
2,500Hz, eliminating the placement of a crossover point in the
middle of critical voice frequencies. The result is super-smooth
phase and power response that delivers extraordinary intel-
Features
ligibility at high output levels.
■ A 3-inch titanium diaphragm compression driver, mounted
to an 80˚ x 70˚ horn with a 1.4-inch exit throat, reproduces frequencies above 2,500Hz. Mackie Designs has implemented a
unique “Vacuum Tube” philosophy for amplifiers designed for
mid and high-frequency reproduction. The FUSSION 3000 features two Trans-Fet amplifiers, one for the midrange driver and
a modified version for the high-frequency compression driver.
Our Trans-Fet technology combines a very simple Class AB
■
■
■
■
■
■
■
■
design topology with special transformers fitted on the amplifier outputs, that assists in eliminating intermodulation distortion by-products. This type of design emulates the celebrated
warmth and transparency of vacuum tube amps. The result is
clear, and accurate reproduction.
■ The FUSSION 3000 delivers deep, quick bass through the
■
■
■
■
Active, high-output, wide dispersion 3-way system
80° x 70° coverage pattern
High output, 133dB in High Pass Mode Operation
Four 12” high-precision transducers
Low distortion, horn-loaded 8” mid-range transducer
3” titanium diaphragm compression driver
18mm birch plywood construction
1500W high-efficiency, high-current amplifier
for woofers
300W Trans-Fet amplifier for mid-range
150W Trans-Fet amplifier for compression driver
On-board acoustic management control system
Integrated ATM hanging and flying hardware
use of four 12-inch high output woofers. Each 12-inch woofer
handles 350 watts RMS long term. Placing four devices within
the cabinet allows the FUSSION 3000 to produce very deep,
precise reproduction of low frequencies. Using four 12-inch
woofers allows low frequency reproduction to be extremely
“quick” compared to other designs. The low frequency amplifier module is an excellent example of the efficiency of active
designs. This amplifier uses a high-efficiency, high-current
topology to produce 1500 watts of power from a module the
Applications
size of a single sheet of paper.
■ Main PA
■ Frequency response of the FUSSION 3000 is linear between
■ Fills
55Hz and 18KHz. The system processor provides complete sys-
■ Night Clubs
tem management of all electronic and acoustic functions includ-
■ Corporate Events
ing electronic active crossover, electronic phase alignment,
electronic time correction, electronic equalization and complete
amplifier and component protection. Because it is designed to
(continued on last page)
1
O FoF86 PAGES
PAGES
SPEAKER
FUSSION 3000
2
FUSSION 3000 3-Way Active Speaker System
Specifications
System Acoustic
Frequency Range (–10dB):
Frequency Response (–3dB):
Horizontal Coverage Angle (–6dB):
45Hz–20kHz
55Hz–18kHz
80˚ averaged
2kHz to 10kHz
Vertical Coverage Angle (–6dB):
70˚ averaged
2kHz to 10kHz
Directivity Factor; DI(Q):
10.19 (10.46) averaged
2kHz to 10kHz
Rated Maximum SPL (long term):
130dB @ 1m
Rated Maximum SPL (peak):
133dB @ 1m
Rated Maximum SPL-High Pass On: 85Hz–18kHz: 132dB
(long term)
Rated Maximum SPL-High Pass On: 85Hz–18kHz: 135dB
(peak)
Crossover Points:
500Hz, 2,500Hz
Dynamic Range:
>110dB
Phase Response:
±35˚ from 500Hz to 10kHz
Audio Input / Output / Controls
Main Input, Loop Out:
50kΩimpedance, balanced
Sub-Out Signal:
85Hz low pass output with
protection and active monitoring
for FUSSION 1800S/1800SA
active subwoofer system
Fill Out Signal:
85Hz high-pass signal
Fill Out Signal Level Control:
0 dB to –30 dB
Fill Out Phase Control:
0˚–180˚
High-Pass Switch:
Allows system to
operate from 85Hz up only
Line Input Power
US:
120VAC, 60Hz
Recommended Amperage Service:
20A
AC Connector:
3 pin Twistlock 250VAC, 20A male
Europe:
230VAC, 50Hz
Recommended Amperage Service:
16A
AC Connector:
3 pin IEC 250VAC, 16A male
In-rush Current Protection:
Yes, transistor based
Transducers
Low Frequency (4 each wired series-parallel)
Cone Diameter:
12” (300mm)
Voice Coil Diameter:
3” (75mm)
Power Handling:
350 watts rms (long term)1
Mid Frequency
Cone Diameter:
8” (200mm)
Voice Coil Diameter:
2” (50mm)
Power Handling:
150 watts rms (long term)1
High Frequency
Diaphragm Diameter:
3” (75mm)
Throat Exit Diameter:
1.4” (35.6mm)
Diaphram Material:
Titanium
Power Handling:
75 watts rms (long term)1
Control System Functions
Amplifiers
Low Frequency:
Rated Output per AES standard @ low frequency
driver impendance:
1000 watts Continuous Average Power
1500 watts peak
Type:
Class G High Efficiency, High Current
Cooling:
Convection Extrusion
Mid Frequency:
Rated Output per AES standard @ mid frequency
driver impendance:
200 watts Continuous Average Power
300 watts peak
Type:
Mosfet Based Class AB
Cooling:
Convection Extrusion
High Frequency:
Rated Output per AES standard @ high frequency
driver impendance:
100 watts Continuous Average Power
150 watts peak
Type:
Mosfet Based Class AB
Cooling:
Convection Extrusion
Hanging Inserts:
Rigging Inserts:
O Fo F86 PA
P AG EGSE S
Electronic Crossover
Phase Alignment
Time Correction
Equalization
Safety Features
RMS Limiting:
Thermal:
Physical
Enclosure:
Handles:
Color:
Grille:
Monitoring and limiting of
continuous RMS output of amplifiers
Monitoring of thermal condition of
power supply and amplifiers. High
temperature condition engages input
stage shut down and auto reset function.
Trapezoidal, 15° side angles,
18mm multi-layered birch
4 points on top
2 points, 1 each side ATM MEGS
1 pull back clip, bottom
4 ea. aluminum/rubber grips
Black, splatter paint
Custom perforated oval steel grille
with anti-corrosive treatment
Dimensions:
Height:
Front Width:
Rear Width:
Depth:
Net Weight:
Options
Active Subwoofer System:
Flyware:
41 in (104.1cm)
25 in (63.5cm)
13.9 in (35.3cm)
23 in (58.4cm)
246 lbs. (112kg)
Fussion 1800SA / 1800S
ATM Megs Compatible
Footnote 1: Power handling for transducers is based on AES long term power testing standard
conducted for 100 hours full power, free air.
2
O FoF66 PAGES
PAGES
FUSSION 3000
3-Way Active Speaker System
FUSSION 3000
Vertical Polars
200Hz
500Hz
250Hz
630Hz
315Hz
800Hz
400Hz
1kHz
1.25kHz
3.15kHz
1.6kHz
4kHz
2kHz
5kHz
2.5kHz
6.3kHz
Vertical Off-Axis Frequency Response (UP)
8kHz
10kHz
12.5kHz
Vertical Off-Axis Frequency Response (DOWN)
16kHz
3
O FoF866 PAGES
PAGES
FUSSION 3000
3-Way Active Speaker System
FUSSION 3000
Horizontal Polars
0˚
0˚
200Hz
500Hz
250Hz
630Hz
315Hz
800Hz
400Hz
1kHz
0˚
0˚
1.25kHz
3.15kHz
1.6kHz
4kHz
2kHz
5kHz
2.5kHz
6.3kHz
Horizontal Off-Axis Frequency Response
0˚
8kHz
10kHz
12.5kHz
16kHz
4
O Fo F86 PA
P AG EGSE S
FUSSION 3000
120
3-Way Active Speaker System
Frequency response
100
80
dB SPL
60
40
20
Fundamental
High Pass On
2nd harmonic
3rd harmonic
0
20
Beamwidth vs. Frequency
100
1000
Frequency (Hz)
10000 20000
Directivity Index
5
O FoF86 PAGES
PAGES
FUSSION 3000
3-Way Active Speaker System
22.64" (575mm)
24.72" (628mm)
13.86" (352mm)
41.89" (1064mm)
22.64" (575mm)
BOTTOM
SIDE
24.72" (628mm)
41.89" (1064mm)
FRONT
6
O Fo F86 PA
P AG EGSE S
REAR
FUSSION 3000 3-Way Active Speaker System
Input/Output Control Panel
Euro/230V Control Panel with IEC AC Connector
WARNING:
CAUTION
ON
FUSE
10A / SB
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SURFACE MAY REACH HIGH TEMPERATURE DURING
STANDARD USE. TO ENSURE PROPER OPERATION ALLOW A MINIMUM OF 6 INS.
OF CLEARANCE FROM THIS SURFACE AND ADEQUATE VENTILATION. TO REDUCE
THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THIS PANEL OR ANY ATTACHED
COMPONENT. NO OPERATOR SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
PARALLEL
LOOP OUT
REPLACE WITH THE SAME TYPE FUSE AND RATING.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE
FUSE
SERIAL NUMBER
MAIN INPUT
HIGH PASS
85Hz - 20kHz
AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE.
DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
MANUFACTURING DATE
FULL RANGE
55Hz - 20kHz
CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE DESIGNS INC, WOODINVILLE, WA, USA
AND MACKIE EUROPE • MANUFACTURED IN ITALY • COPYRIGHT ©1998 •
THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGNS INC.:
"MACKIE", AND THE "RUNNING MAN" FIGURE • PATENT PENDING
16A - 230 VAC
POWER (GREEN)PIN 1- GND / PIN 2- POS (+) /
PROTECT (RED)
PIN 3- NEG (-)
FILL OUT
85Hz - 20kHz
OUTPUT
LEVEL
SUB-OUT
20Hz - 85Hz
FUSSION 3000
FS
™
0
10
PHASE
0˚
180˚
7
O FoF86 PAGES
PAGES
SPEAKER
FUSSION 3000
FUSSION 3000 3-Way Active Speaker System
Architects’ and Engineers’ Specifications
The active, 3-way, full-range loudspeaker system shall
incorporate four 12-inch low-frequency (LF) transducers,
one horn-loaded 8-inch mid-frequency (MF) transducer and
a 1.4-inch exit, 3-inch titanium diaphragm, compression
driver high-frequency (HF) transducer. The LF drivers shall be
mounted in a vented, multi-ply birch wood enclosure, tuned
for optimum low-frequency response. The MF transducer
shall be sealed from the rear and loaded on a one-piece horn
assembly providing optimum compression ratio and dispersion characteristics. The HF transducer shall be mounted on
an aluminum, constant-directivity horn. The system shall provide a nominal coverage pattern of 80˚ (horizontal) x 70˚ (vertical). System frequency response shall vary no more than
±3dB from 60Hz to 18kHz measured on axis. The loudspeaker
shall incorporate a low-frequency amplifier, capable of delivering 1500 watts over a frequency range of 20Hz to 500Hz.
The system shall incorporate a 300-watt amplifier specifically
designed to power the MF driver over the range of 500Hz
to 2.5kHz and a 150-watt amplifier specifically designed to
power the highfrequency driver over the range of 2.5kHz to 20kHz. The
amplifiers shall be mounted on an aluminum heat sink
installed within the cabinet. The loudspeaker enclosure shall
have a trapezoidal shape and shall incorporate four side handles along with hanging and rigging hardware. The system
will include a control panel with XLR input connector and an
XLR loop-through signal connector, a high-pass or full-range
mode selection switch, a sub-out XLR connector providing
low-pass audio and control signal for subwoofer systems, a
“Fill-Out” XLR connector with level and phase controls, and
power and protection mode LED indicators. The front of the
loudspeaker shall be covered with a powder-coated, weatherresistant perforated steel grille.
The active 3-way full-range loudspeaker system shall be
the Mackie Designs FUSSION 3000.
(continued from first page)
deliver very high output levels (133dB peak-full range) and
wide dispersion, the system can only be line-arrayed with
other FUSSION 3000 cabinets. The system’s wide dispersion
characteristics do not allow it to be used in large arrays.
■ FUSSION 3000 is the first professional speaker system
to create a completely ideal union between transducers
and amplifiers. To ensure long-term reliability and performance, the amplifier cards and processor are mounted to a
huge heat sink eliminating the need for fans, dramatically
extending life expectancy and eliminating maintenance
cycles. An easily-accessible rear input and control panel
offers substantial signal routing flexibility. All audio connections are via XLR connectors, including a main input with a
loop-through output for connection to other enclosures.A
Full Range/High Pass switch allows the FUSSION 3000 to
be operated full range or above 85Hz only. A SUB-OUT connector allows simple connection to the Fussion 1800AS/
1800S active subwoofer system. The SUB-OUT signal is
low-passed below 85Hz and also contains the limiting and
protection circuitry for the active subs. For sound reinforcement situations where “fill” speakers are needed, there is a
Fill-Out connector with level and (0˚–180˚) phase controls.
Mackie’s FUSSION 3000 can run on 115V AC or 230V AC
single phase. The system features soft-start circuitry that
eliminates “pops” and precisely controls AC in-rush current
surges.
Electronic files for this product available at:
www.mackie.com
This Specification Sheet
FUSSION3000.PDF
Architects’ & Engineers’ Specifications FUSSION3000AE.TXT
Quick-Start Manual
FUSSION3000QS.PDF
Applications Guide
FUSSION3000AG.PDF
Owner/Operator’s Manual
FUSSION3000ML.PDF
CADD files
FUSSION3000.DXF
EASE data
FUSSION3000.EAS
www.mackie.com
16220 Wood-Red Rd NE, Woodinville, WA 98072 USA
800.898.3211, fax 425.487.4337, [email protected]
UK +44 1268 571 212, fax +44 1268 570 809, [email protected]
ITALY +39 0522 354 111, fax +39 0522 332 294, [email protected]
FRANCE +33 3 8546 9160, fax +33 3 8546 9161, [email protected]
GERMANY +49 2572 96042 0, fax +49 2572 96042 10, [email protected]
Mackie continually engages in research related to product improvement. New material, production methods, and design refinements are introduced into existing products without notice as a routine expression of that philosophy. For this reason, any current Mackie product may differ in some respect from its
published description, but will always equal or exceed the original design specifications unless otherwise
stated. ©1999-2000 Mackie Inc. All rights Reserved.
and
are registered trademarks of
Mackie Inc. Mackie is a trademark of Mackie Designs Inc.
part no. 910-225-00 Rev A
8
O FoF86 PAGES
PAGES
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement