Mytee | Contractor's Special 2000CS | User manual | Mytee Contractor's Special 2000CS User manual

Mytee Contractor's Special 2000CS User manual
Instructions for
Contractor’s Special™ 2000CS/2001CS
Please read before use.
Register your product
at www.mytee.com/help
Model #
2000CS p.2
2001CS p.8
General & Maintenance information p.14
Serial #
Form # ADM-CS
3-12
13655 Stowe Dr., Poway, CA. 92064
1
CONTRACTOR’S SPECIAL™ 2000CS
7
2000CS FRONT
2000CS BACK
8
1
2
3
6
14
13
4
9
12
5
11
1. Waist high controls
2. 2” Male Cuff-Lynx™
3. Female QD
4. Solution tank
5. Front vent
6. Solution lid
7. Push handle
8. Recovery tank lid
9. 3” casters
10. 8” wheels
11. Rear vent
12. 25’ Power cord
13. Bucket-high drain valve
14. Recovery tank
2000CS ACCESSORIES
10
REPLACING HOSE CUFFS WITH CUFF-LYNX™
8300 EZ C - 1 2” Wand
Twist clock-wise to remove standard cuffs.
850 1 - 15’ 1-1/2” Vac/Sol Hose
Twist counter clock-wise to attach Cuff-Lynx™ to vac. hose.
H226 - Drain Elbow
Once you receive your Contractor’s Special™, you will need to
replace the cuffs on your vacuum hose. To remove old cuffs, twist
clock-wise. To attach reducer Cuff-lynx™ to vacuum hose twist
counter clock-wise.
H141 - 1 1/2” Cuff-Lynx™
2
CONTRACTOR’S SPECIAL™ 2000CS
ATTACH VAC & SOLUTION HOSE TO WAND
2000CS ATTACH HOSES
Firmly attach hose and quick disconnect. Make sure quick disconnects snap together firmly. Once attached to unit connect Q.D. to
upholstery tool. Always inspect hoses for cracks or fraying.
Attach hose cuff to end of wand tube. Attach female QD to male
QD located near the wand trigger.
2000CS VACUUM & PUMP
2000CS FILL SOLUTION TANK
M
UU
C
VA
Lift lid to fill. For best results, fill with warm water (140o F).
MP
PU
To use vacuum, turn on vacuum. To use pump, turn on pump.
3
CONTRACTOR’S SPECIAL™ 2000CS
2000CS RECOVERY DRAIN
2000CS LOCKING CASTERS
When the float shuts off vacuum, empty tank. Pull lever located at
the back of the machine to release water.
Locking casters help keep the machine remain stationary during
use.
2000CS ADDING DEFOAMER
2000CS SYSTEM MAINTAINER
Add a defoamer in the recovery tank to reduce foam, prolonging
the life of the Contractor’s Special™ vacuum motor .
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
4
Order parts at: www.mytee.com/products/product.php?id=2000CS
5
C
D
E
F
Part prices are subject to change.
A
B
8
7
bolt, 1/4x20x3/4" hex head
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
H222
H273
B105
B136
AH108S
H202
H768
H330
H501
P735
14
15
16
17
18
19
20
21
22
23
G052
40
B216
49
50
8
B186
H299
48
H204
H211
39
H201
H215
38
47
P757
37
46
H219
36
H378
H239
35
H770
H224
34
45
H254
33
44
E532
32
H307
H220
H912
H221
30
31
43
C302
29
42
washer, buna 1-1/8" od x 3/16" id
G059
28
H203
H217
27
41
washer, 1/4"id x 1"od, flat, s/s
H300
26
gasket, vacuum motor
7
nipple, brass, 3/8" x close
washer, 11/16"id x 1-1/2"od x .075, s/s
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
bolt, 1/4-20 x 1 3/4" hex head, s/s
bolt, 1/4-20 x 1/2", hex head, zinc
bracket, front hinge, sp/fb
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
washer, star, 1/4" steel zinc
bracket, rear, fb/spy
bolt, 1/4-20 x 1 1/4"
nut, hex, 1/4-20 s/s
sol tank, firebird
cap, axle, 1/2"
wheel, 8"
axle, 17.50" x .50" dia, fb
washer, axle, cut 1/2" id
power cord, end, 25', 14/3
fitting, strain relief, cord
nut, lock, 1/2" steel
vac motor, 3 stage, 120V, tangential
exhaust boot, plastisol
clamp, hose, 2-1/4 dia
cuff, black 1-1/2"
vac hose, 1-1/2", black, wire reinforced
G004
PH627-24
24
25
manifold, single vac, no gasket
vac support, 3 stage, 4-1/16"
plate, single manifold, 6.5" x 9"
sol hose, 1/4" x 24 1/2", (OAL)
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
bushing, brass, 3/8"mpt x 1/4"
nut, kep, #10-32 zinc
screw, #10-32 x 1-1/4" phil pan head, zinc
clamp, hose, 5/16-29/32
adapter, brass, 1/2" barb x 3/8" fsw, ball end
B160
H347
sol hose, 1/2" kuri, 100 psi
13
PH615-26
11
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
pump, 120psi, demand, 115V
screw, #10 x 5/8" hex head, zinc
guard, cooling fan, wire
washer, 1/4" lock, s/s
bolt, 1/4-20 x 1" hex head, s/s
caster, 3", Black Hub, Gray Tread
12
B172
10
H296
H343
H213
6
7
C305
H342
5
9
H667
4
8
H210
3
washer, 1/4" flat, s/s
base, firebird
nut, lock, 1/4-20, nylon insert, s/s
P756
H216
1
DESCRIPTION
2
PART NO.
ITEM
NO.
1
5
1
2
2
1
8
4
1
2
4
4
2
1
2
2
1
2
1
1
1
1
1
2
1
1
1
1
3
1
5
3
1
1
1
4
4
4
1
1
1
1
9
2
4
8
2
18
12
1
QTY.
6
6
$1.99 ea
$0.99 ea
$8.99 ea
$0.99
$0.99 ea
$8.99 ea
$0.99 ea
$0.99 ea
$9.99 ea
$0.99 ea
$1.99 ea
$0.99
$0.99 ea
$149.99 ea
$0.99 ea
$28.99 ea
$9.99 ea
$0.99 ea
$44.99 ea
$3.19 ea
$1.99 ea
$139.99 ea
$4.99 ea
$1.49 ea
$5.99 ea
$6.49/ft
$8.99 ea
$14.99 ea
$4.99 ea
$7.99 ea
$0.99 ea
$0.99
$26.49 ea
$4.99 ea
$3.19 ea
$0.99 ea
$0.99 ea
$1.99 ea
$3.49 ea
$8.99/ft
$9.49 ea
$151.99 ea
$0.99 ea
$2.99 ea
$0.99 ea
$0.99
$14.99 ea
$0.99 ea
$0.99
$147.99
MSRP
B111
B102
AH105
H244
PH633-11
56
57
58
59
60
H135
G083
A926
67
68
69
H326
E515
74
75
nipple, brass, 1/4"m, hex
washer, 9/16"id x 1"od, flat, s/s
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
gasket strip, 3/4" x 36" x 1/8"
strap, velcro, w/buckle
plug, vent, heyco, 1/2"
G010
G085
G147
H434
5
4
cuff-lynx instruction guide
quick disconnect, 1/4" female x 1/4" fpt
B102
ADM-CUFF-LYNX
quick disconnect, male, 1/4" male x 1/4" fpt
B101
strap, velcro, w/buckle
vac hose, 1-1/2" 15' SW
H295
stop sign register your product
sol hose, 1/4" x 16', 3000psi
A942
G147
spout, drain, 45 degree
AD127
wand, 12" collapsable, w/disconnects
H226
H141
8350C
DESCRIPTION
cuff-lynx, 2" to 1.5" reducer
PART NO.
Accessories
DESCRIPTION
filter, bag, vac tank, drawstring
PART NO.
switch, rocker, 2 position
plate, switch, 3 hole, fb
fitting, inlet, pvc, 1-1/2", gray
bracket, "L" (all extracters)
valve, drain, 1-1/2"
vac tank, firebird
elbow, inlet assembly 2"
gasket, 2" inlet
Cuff-Lynx, 2" m cuff x 2" mpt
screw, #8 x 5/8 phil oval, s/s
lid, vac tank, black, 7"
gasket, 7", vac lid
float, 1.5", ball style
elbow, U, 180, 1-1/2", float
screw, 8 x 1/2", hex head, zinc
pipe, pvc, 1-1/2"
adapter, pvc, 1-1/2" fms x fmpt
hose, 3/8" x 17-1/2", (OAL)
qd, brass, 1/4" f
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
Items Not Shown
H229
73
H225
H390A
72
71
P758
H304
70
G090
64
66
G091
63
65
P755
H235
62
H297
B107
55
61
H212
54
B103
53
filter, strainer, 1/2"
bushing, brass, 1/2"mpt x 3/8" fpt, hex
B119A
B210
4
DESCRIPTION
5
PART NO.
52
ITEM
NO.
51
3
1
1
5
1
1
1
1
1
1
1
3
QTY.
2
1
2
1
QTY.
2
1
1
2
1
1
1
1
1
6
1
1
1
1
3
1
1
1
1
1
2
4
2
1
1
QTY.
n/a
n/a
$3.49 ea
$17.99 ea
$8.49 ea
$42.00 ea
$71.99 ea
$3.19 ea
$159.99 ea
$3.99 ea
MSRP
$4.48 ea
$3.49 ea
$4.99 ea
$9.99 ea
MSRP
$13.99 ea
$6.99 ea
$5.99 ea
$6.99 ea
$20.99 ea
$186.99 ea
$15.99 ea
$2.49 ea
$3.99 ea
$0.99 ea
$36.99 ea
$11.99 ea
$19.99 ea
$8.99 ea
$0.99 ea
$4.99/Ft
$4.99 ea
$31.99 ea
$17.99 ea
$3.49 ea
$3.19 ea
$0.99 ea
$4.49 ea
$6.49 ea
$2.49 ea
MSRP
NAME
D. Cano
DATE
2/28/12
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
2
SCALE: 1:8
1
DO NOT
SCALE DRAWING
2000CS
SIZE DWG. NO.
C
SHEET 1 OF 2
OD
REV
PRODUCTS, INC.
858-679-1191
contractors special
mytee
TITLE:
1
A
B
C
D
E
F
CONTRACTOR’S SPECIAL™ 2000CS PARTS & PRICING
8
to sol tank
thru B186 (#48)
11
12
10
13
8
14
9
15
3
7
to sol tank
thru B103 (#53)
7
5
16
18
17
20
3
29
6
4
3
22
23
24
25
26
19
8
6
21
20
1
27
30
33
31
28
34
35
2
36
32
5
52
3
47
51
3
49
49
49
46
50
6
37
49
49
49
48
39
45
38
6
40
39
41
to pump "IN"
thru B160 (#12)
40
4
57
56
54
61
42
54
53
55
54
55
58
44
43
53
59
60
67
74
63
64
68
to pump "OUT"
thru AH108S-25 (#18)
75
62
3
73
65
44
66
2
72
70
69
NAME
D Cano
DATE
2/28/12
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
71
D
SIZE DW
c
myt
TITLE:
CONTRACTOR’S SPECIAL™ 2000CS PARTS & PRICING
CONTRACTOR’S SPECIAL™ 2000CS WIRING DIAGRAM
7
CONTRACTOR’S SPECIAL™ 2001CS
7
2001CS FRONT
2001CS BACK
8
1
2
3
6
14
13
4
9
12
5
11
1. Waist high controls
2. 2” Male Cuff-Lynx™
3. Female QD
4. Solution tank
5. Front vent
6. Solution lid
7. Push handle
8. Recovery tank lid
9. 3” casters
10. 8” wheels
11. Rear vent
12. 25’ Power cord
13. Bucket-high drain valve
14. Recovery tank
2001CS ACCESSORIES
10
REPLACING HOSE CUFFS WITH CUFF-LYNX™
8300 EZ C - 1 2” Wand
Twist clock-wise to remove standard cuffs.
850 1 - 15’ 1-1/2” Vac/Sol Hose
Twist counter clock-wise to attach Cuff-Lynx™ to vac. hose.
H226 - Drain Elbow
Once you receive your Contractor’s Special™, you will need to
replace the cuffs on your vacuum hose. To remove old cuffs, twist
clock-wise. To attach reducer Cuff-lynx™ to vacuum hose twist
counter clock-wise.
H141 - 1 1/2” Cuff-Lynx™
8
CONTRACTOR’S SPECIAL™ 2001CS
2001CS ATTACH HOSES
ATTACH VAC & SOLUTION HOSE TO WAND
Firmly attach hose and quick disconnect. Make sure quick disconnects snap together firmly. Once attached to unit connect Q.D. to
upholstery tool. Always inspect hoses for cracks or fraying.
Attach hose cuff to end of wand tube. Attach female QD to male
QD located near the wand trigger.
2001CS FILL SOLUTION TANK
2001CS VACUUM, PUMP & HEATER
M
UU
C
VA
Lift lid to fill. For best results, fill with warm water (140o F).
MP
PU
R
E
AT
HE
To use vacuum, turn on vacuum. To use pump, turn on pump.
For heater, turn on heater.
9
CONTRACTOR’S SPECIAL™ 2001CS
2001CS RECOVERY DRAIN
2001CS LOCKING CASTERS
When the float shuts off vacuum, empty tank. Pull lever located at
the back of the machine to release water.
Locking casters help keep the machine remain stationary during
use.
2001CS ADDING DEFOAMER
2001CS SYSTEM MAINTAINER
Add a defoamer in the recovery tank to reduce foam, prolonging
the life of the Contractor’s Special™ vacuum motor .
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
10
CONTRACTOR’S SPECIAL™ 2001CS PARTS & PRICING
7
8
F
E
D
C
B
A
6
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
1
2
3
4
5
6
H273
H230
H528
E571
H275
H274
nut, kep, #10-32 zinc
screw, 10-32 x 1/2 phil pan
bracket, heater mounting, dual
heating rod, 600W, 115V
6-32 x 3/16 p-pan internal sem zinc
screw, #6 x 3/16, phil pan head, self-tapping
6
2
1
2
8
2
$0.99 ea
$0.99 ea
$29.99 ea
$49.99 ea
$0.99 ea
$0.99 ea
7
8
9
10
11
12
13
E574
E573
H903A
B103
AH108S
AH156
B207
Thermostat, 310°F ± 10°F, Manual, 1/4"
Thermostat, 200°, Auto, 1/4"
heater, aluminum cast, single
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
sol hose, 1/4" x 24 1/2", (OAL), f x fsw, 3000psi
hose, 3/8" x 6.5", (OAL), f x fsw, 5400 Gray
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt
2
2
2
5
1
1
1
$17.99 ea
$16.49 ea
$78.99 ea
$4.49 ea
$26.49 ea
$23.99 ea
$5.99 ea
14
15
16
17
18
19
20
21
22
23
B108
AH103
B136
B105
C305
B172
PH615
H347
B160
H217
valve, brass, 1/4" check
hose, 3/8" x 10", (OAL), f x fsw, surge, 1600psi
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
bushing, brass, 3/8"mpt x 1/4"
pump, 120psi, demand, 115V
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
sol hose, 1/2" kuri 100psi
clamp, hose, 5/16-29/32
adapter, brass, 1/2" barb x 3/8" fsw, ball end
clamp, hose, 2-1/4 dia
1
1
1
1
1
1
1
4
1
3
$13.99 ea
$30.49 ea
$4.99 ea
$3.19 ea
$151.99 ea
$9.49 ea
$8.99 ea
$1.99 ea
$3.49 ea
$1.49 ea
24
25
26
27
PH627
H300
H770
C302
vac hose, 1-1/2", wire reinforced
cuff, black 1-1/2"
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
vac motor, 3 stage, 120V, tangential
1
1
11
1
$6.49 ea
$5.99 ea
$0.99 ea
$139.99 ea
28
29
30
31
H343
G004
H501
H330
screw, #10 x 5/8" hex head, zinc
gasket, vacuum motor
vac support, 3 stage, 4-1/16"
plate, single manifold, 6.5" x 9"
9
1
3
1
$0.99 ea
$8.99 ea
$4.99 ea
$7.99 ea
32
33
34
35
36
37
H204
H201
P735
H768
H216
H222
bolt, 1/4-20 x 1-3/4" hex head, s/s
bolt, 1/4-20 x 1/2", hex head, zinc
manifold, single vac, no gasket
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
nut, lock, 1/4-20, nylon insert, s/s
screw, #10-32 x 1-1/4" phil pan head, zinc
3
2
1
3
13
4
$0.99 ea
$0.99 ea
$14.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
38
39
40
41
42
43
H210
PH628
H020
H135
H229
H667
washer, 1/4" flat, s/s
vac hose, 2", wire reinforced
nut, lock, 2", steel
Cuff-Lynx, 2" m cuff x 2" mpt
fitting, inlet, pvc, 1-1/2", gray
caster, 3", Black Hub, Gray Tread
16
1
1
2
1
2
$0.99 ea
$8.99/ft
$4.99 ea
$3.99 ea
$5.99 ea
$14.99 ea
44
45
H342
H296
bolt, 1/4-20 x 1" hex head, s/s
guard, cooling fan, wire
8
2
$0.99 ea
$2.99 ea
46
47
48
49
P756
H221
H220
E531
base, firebird
nut, lock, 1/2" steel
fitting, strain relief, cord
power cord, end, 25', 12/3 black
1
1
1
1
$147.99
$1.99 ea
$3.19 ea
$52.99 ea
50
51
52
53
H254
H224
H239
H219
washer, axle, cut 1/2" id
axle, 17.50" x .50" dia, fb
wheel, 8"
cap, axle, 1/2"
4
1
2
2
$0.99 ea
$9.99 ea
$28.99 ea
$0.99 ea
54
55
56
57
58
59
60
61
62
P757
G061
H215
H213
H211
G052
H203
H316
H378
sol tank, firebird
cover, sol tank, fb
nut, hex, 1/4-20, s/s
washer, 1/4" lock, s/s
washer, 1/4"id x 1"od, flat, s/s
washer, buna 1-1/8" od x 3/16" id
bolt, 1/4-20 x 1-1/4" hex head
bolt, 1/4-20 x 1-1/2" hex head, s/s
bracket, front hinge, sp/fb
1
1
2
4
4
4
2
2
1
$149.99 ea
$12.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$1.99 ea
$0.99 ea
$0.99 ea
$8.99 ea
63
64
B119A
B210
filter, strainer, 1/2"
bushing, brass, 1/2"mpt x 3/8" fpt, hex
1
1
$6.49 ea
$2.49 ea
65
66
67
68
H299
B216
B186
B111
washer, 11/16"id x 1-1/2"od x .075, s/s
nipple, brass, 3/8" x close
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
4
1
1
1
$0.99 ea
$1.99 ea
$8.99 ea
$3.49 ea
69
70
71
72
73
74
75
76
H212
B102
H413
B107
AH105
H912
H244
PH633-11
washer, 9/16"id x 1"od, flat, s/s
qd, brass, 1/4" f
washer, nylon, 9/16id x 1-1/16od x .031
nipple, brass, 1/4"m, hex
hose, 3/8" x 17-1/2", (OAL), f x -fsw, surge, 1600psi
bracket, rear, fb/spy
adapter, pvc, 1-1/2" fms x fmpt
pipe, pvc, 1-1/2"
4
1
2
2
1
1
1
1
$0.99 ea
$17.99 ea
$0.99 ea
$3.19 ea
$31.99 ea
$9.99 ea
$4.99 ea
$4.99/Ft
77
78
79
H297
P755
H235
screw, #8 x 1/2", hex head, zinc
elbow, U, 180, 1-1/2", float
float, 1.5", ball style
80
G091
gasket, 7", vac lid
3
1
1
1
$0.99 ea
$8.99 ea
$19.99 ea
$11.99 ea
8
5
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
81
82
83
84
G090
H304
G002
A926
lid, vac tank, black, 7"
screw, #8 x 5/8 phil oval, s/s
gasket, cam fitting polyethylene, 2.35" OD 1.90" ID
elbow, inlet assembly 2"
1
6
1
1
$36.99 ea
$0.99 ea
$6.49 ea
$15.99 ea
85
86
87
P758
H225
H226
vac tank, firebird
valve, drain, 1-1/2"
spout, drain, 45 degree
1
1
1
$186.99 ea
$20.99 ea
$3.19 ea
88
89
90
91
H390A
H326
H246
E515
bracket, "L" (all extracters)
plate, switch, 3 hole, fb
screw, #8-32 x 3/8" SHCS, alloy
switch, rocker, 2 position
2
1
4
3
$6.99 ea
$6.99 ea
$0.99 ea
$13.99 ea
ITEMS NOT SHOWN:
PART NO.
DESCRIPTION
QTY.
ADM-HP60
manual, spyder
1
AD127
A935
A942
B101
B102
G008
G029
G085
G147
stop sign, register your product
sol hose, pig tail, 1/8" x 7 1/2"
sol hose, 1/4" x 16', 3000 psi
quick disconnect, male, 1/4" male x 1/4" fpt
quick disconnect, 1/4" female x 1/4" fpt
piglet filter
banana bag, mesh bag, yellow
gasket, strip, 3/4" x 36" x 1/8"
strap, velcro, w/buckle
1
1
1
2
1
1
1
1
5
$14.99 ea
$71.99 ea
$8.49 ea
$17.99 ea
$6.29 pak
$3.99 ea
$4.99 ea
$3.49 ea
H230
H282
H375
screw, 10-32 x 1/2" phil pan head, s/s
tool, upholstery, s/s w/valve
hanger, wire formed, hose
4
1
2
$0.99 ea
$98.99 ea
$10.99 ea
H701
hose, vac, 15' x 1-1/4" w/1-1/2" black cuffs
1
$44.99 ea
6
7
Order parts at: www.mytee.com/products/product.php?id=2001CS
11
MSRP
5
Part prices are subject to change.
4
12
A
B
C
D
E
F
*
7
4
3
8
1
8
2
9
11
10
10
12
# 10
45
28
10
To female q.d.
thru B103
44
38
36
7
# 67
43
20
22
To filter in sol tank
thru B186
7
13
14
15
19
21
41
18
20
23
46
16
# 40
6
To vac
motor exhaust
thru H244
17
24
25
6
34
47
1
37
26
48
50
35
38
36
27
28
51
49
29
32
30
53
31
52
40
# 41
5
To inlet
on base
23
5
61
38
39
23
63
36
64
65
38
57
66
65
62
54
65
65
33
67
56
58
57
55
58
59
60
4
# 22
To pump "IN"
thru B160
59
4
70
68
69
71
72
71
69
10
3
10
69
69
72
26
# 11
76
74
75
77
To heater "OUT"
thru AH108S
73
26
3
91
90
78
85
79
41
80
2
42
82
81
83
2
26
NAME
DATE
88
V. LaBarbera 7/2011
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
26
84
TITLE:
858-679-1191
87
1
DO NOT SCALE
DRAWING
2001CS
SCALE: 1:5
REV
SHEET 2 OF 2
OD
Contractor’s
Special
SIZE DWG. NO.
D
86
mytee PRODUCTS, INC.
85
1
C
D
E
F
A
B
A
8
CONTRACTOR’S SPECIAL™ 2001CS PARTS & PRICING
Cord Input Primary
L2
GND
Black
Inline Conn.
Green
W hite
B lack
G reen
SW- DPST
E515
Inline Conn.
Switch
Pressure
C305
Inline Conn.
White
Pressure Pump
L2
Black
Inline Conn.
Green
W hite
B lack
C302
Inline Conn.
E515
SW- DPST
Inline Conn.
Vacuum Motor 1
L2
G ND
L1
B lack
B lue
G reen
G ND
L1
B lack
Y ellow
Black
2001CS
E515
SW- DPST
Thermal Switch
E571
Green
Thermal Switch
E571
Heater 2
Heater 1
Mytee Products
13655 Stowe Dr.
Poway, CA
Size: L egal
Number: 0000
Revision: A
92064
--Time: 4:38:47 PM Sheet1 of 1
Date: 3/11/2011
File: Z:\Engineering\GHI\GHI Projects\MYTEE\Mytee Schematics\HP100\HP100 Schematic.SCHDOC
Title
White
W hite
T hermal Switch
L2
L1
Orange
G reen
G ND
W hite
T hermal Switch
L2
L1
13
Orange
G reen
G ND
L1
CONTRACTOR’S SPECIAL™ 2001CS WIRING DIAGRAM
B lack
GENERAL INFORMATION
Dear Customer:
Unpacking the Machine
Congratulations on the purchase of your new Contractor’s Special™. As you are
already aware, the scene of the equipment world is becoming more high tech, and
we at Mytee Products Inc. strive to keep you on the cutting edge with superior
quality and technology.
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to file a
freight damage claim.
Keep in mind that the Contractor’s Special™ is a machine, so neglect or abuse
will cause unnecessary damage and void the warranty. However with simple
maintenance the Contractor’s Special™ will give quality performance for many
years to come.
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
If warranty questions arise, please consult your user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts or
ordering parts, please call an authorized Mytee Products Inc. Service Center.
To see an updated list, visit our website at www.mytee.com
Is used to warn of immediate hazards that will cause severe personal injury or death.
Before you begin cleaning, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Is used to call attention to a situation that could cause severe personal injury.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical shock. This machine is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed in accordance
with all local code and ordinances. Do not remove ground pin; if missing, replace
plug before use.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.
To reduce the risk of fire, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
3. Always unplug power cord from electrical outlet before attempting any adjustments
or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp
edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not in use.
10. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
11. Do not use in areas where flammable or combustible material may be present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.
14. Keep hair, loose clothing, fingers, and all parts of the body away from all
openings and moving parts.
15. Use extra care when cleaning on stairs.
16. To reduce the risk of fire or electric shock, do not use this machine with a solidstate speed control device.
17. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alkalines, or other dangerous liquids.
19. Do not leave operating unattended.
Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service person if you are in doubt
as to whether the outlet is properly grounded. Do not modify the plug provided with
the machine. If it will not fit the outlet, have a proper outlet installed by a qualified
electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualified electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Grounded Outlet
Adapter
Metal
Screw
Grounding Pin
Grounded Outlet Box
Figure 1
Parts and Service
Figure 2
Filling the Solution Tank
Tab for Grounding
Screw
1. Fill the solution tank with the approved cleaning solution.
2. Do not fill up the solution tank completely: 1” should be left free at the top.
3. Typically, the solution should be a mixture of water and a cleaning chemical
appropriate for the type of job.
4. Always follow the dilution instructions on the chemical container label.
5. The temperature of the cleaning solution must not exceed 70oC/160oF.
Figure 3
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the Model and Serial Number
when discussing your machine.
Name Plate
Use only non-flammable liquid in this machine.
The Model and Serial Number of your machine are shown on the Nameplate on the
back panel of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
14
Setup
Maintenance Schedule
1. Open lid of solution tank. Fill solution with water or approved cleaning agent. For
best results, fill with warm water (140o).
Flammable materials can cause an explosion or fire. Do not use flammable solutions
or materials in tank(s).
FOR SAFETY: When using machine, follow mixing and handling instructions on
chemical containers.
ATTENTION: If using powdered cleaning chemicals, mix prior to adding.
Maintenance item
Daily
Clean and inspect Tanks
Clean and inspect Hoses
Check filters
Check power supply cable
Clean machine with all purpose cleaner and cloth
Check spray nozzles
Flush solution system with Mytee system maintainer
Remove and clean float shut-off screen from tank
Inspect vacuum hoses for holes and loose cuffs
x
x
x
x
x
Once a week
x
x
x
x
Trouble Shooting
2. Attach solution hose (located front of machine). NOTE: Make sure the quick
disconnect snap together firmly. As you do this, always inspect hoses for cracks or
fraying. Do not use if hoses are damaged.
3. Attach other end of solution hose to wand.
4. Attach vacuum hose to recovery tank.
5. Plug machine’s cord into a grounded wall outlet. FOR SAFETY: Do not operate
machine unless cord is properly grounded. FOR SAFETY: Do not operate machine
with the use of an extension cord.
6. Turn on pump. Key tool until you have a steady flow.
7. Release tool trigger. Turn on heater.
8. Wait 8–10 minutes for unit to pre-heat.
9. Re-key upholstery tool until hot water begins flowing.
10. Once hot water is flowing, release trigger and pre-heat an additional 4–5 minutes.
11. Turn on vacuum motor.
12. Begin cleaning. Make two dry passes to every wet pass.
13. For floor cleaning, unplug tool and attach floor wand.
14. Work away from cords to avoid damage.
15. Use a defoamer in your recovery tank.
16. To clean heavily soiled areas, repeat cleaning from different directions.
17. When float shuts off vacuum, empty tanks.
18. When work is complete, unplug cords and hoses.
19. Wrap and clean hoses. Clean all tanks.
There is no power.
1. Plug machine in proper outlet.
2. Check circuit breaker; reset circuit breaker, other items should not run on the
same circuit as machine. Outlet must be a 20-amp circuit.
Pump does not work properly.
1. Snap quick disconnects firmly together.
2. Check solution tank; may be empty.
3. Jets clogged, remove jet and flush clean.
4. Filters clogged, remove filters and rinse clean with water.
5. Heater is blocked; flush out with Mytee’s system maintainer.
6. If brass check valve is stuck replace valve.
7. Check pump wire. May need to reconnect wire.
8. Switch plate switch may need to be replaced.
9. If pump motor brushes are worn, replace pump.
Heater does not work properly.
1. If sensor mounted on the heater has popped, reset sensor by pushing in button.
2. Heating element may need to be replaced.
Vacuum motor does not work properly.
1. Check that hose is tightly connected.
2. Close drain hose valve completely.
3. Secure the vacuum tank tightly.
4. If ball float is shut off, empty vacuum tank of all wastewater.
5. Make sure ball float is firmly installed on the elbow.
6. If water is coming out of vacuum motor, use a low foaming detergent.
7. Clean upholstery tool or floor wand jets.
Pre-Operation
1. Vacuum carpet and upholstery and remove other debris.
2. Perform machine setup procedures.
3. Inspect power cord for damage.
Operation
FAQs
1. Turn pump switch on.
2. Pull up on tool lever to release air in the line. Hold lever until a steady flow of water
comes out of the wand.
3. Once pump is primed and there is pressure in the solution line, turn on heater switch
(if model is equipped with heater) and wait a few minutes for water to heat up.
4. Once water is heated, turn on vacuum and begin cleaning.
Note: When cleaning upholstery, always check manufacturer’s cleaning instructions.
Q: How much does the Contractor’s Special™ weigh and what are the shipping
dimensions?
2000CS
A: 79 Pounds - Box dimensions are 29 3/4” x 19” x 46 1/4”. Must ship motor freight.
2001CS
A: 85 Pounds - Box dimensions are 29 3/4” x 19” x 46 1/4”. Must ship motor freight.
Q: What comes standard with the Contractor’s Special™?
A: The Contractor’s Special™ comes with 15’ 1-1/4” Vacuum/Solution Hose and a
12” wand and Cuff-Lynx™ reducer.
1. Work away from outlet and power cord to prevent cord damage.
2. Use a recommended foam control solution in the recovery tank to prevent vacuum
motor damage. Periodically check for excessive foam buildup in solution tank, and
recovery tank.
3. To clean heavily soiled areas, repeat cleaning path from different direction.
4. When ball float shuts off vacuum, it is time to empty the dirty water from the
recovery tank, and refill solution tank.
5. After cleaning, relieve water pressure from tool before disconnecting hose.
Squeeze trigger for five seconds after turning main power switch off.
Q: Where do I plug the machine in?
A: The Contractor’s Special™ requires a 20A grounded circuit. Please note: GFI
outlets may trip before the breaker setting.
Q: What is the proper pre heat cycle for the 2001CS?
A: Turn pump switch to the on position and prime pump through the solution hose
and the tool. Then turn the heater switch to the on position. Let the machine sit idle
for 8-10 minutes. Spray tool until you feel the hot water from the jet. Let machine sit
idle for an additional 3-5 minutes. This will insure the water in the heater and hoses
will be at the hottest point to start cleaning.
After Use
1. Unplug.
2. Empty solution tank and rinse it with clean water.
3. Inspect hoses and replace if damaged.
4. Inspect solution filter. Clean or replace if damaged.
5. Store the machine in a clean, dry place.
6. Open recovery tank cover to promote air circulation.
Q: Are the pumps re-buildable for the Contractor’s Special™?
A: Yes, both the seals and the pistons have repair kits available.
Please see the pump manual that shipped with your machine for the
maintenance schedule.
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow excess
moisture in the vacs to dry off. You should also run a System Maintainer through
the system to keep the hoses, pump, and heater clean and free of debris.
15
Warranty
without violating the law.
Mytee Products, Inc. endeavors to provide high quality products and product support
to its customers and therefore backs up all of its new products purchased from Mytee
Products Inc. (Mytee) or any authorized Mytee distributor/service center with this
limited warranty.
The validity, construction and performance of this warranty policy shall be governed
by the laws of the State of California, without respect to conflicts of laws principles.
The exclusive jurisdiction of any legal action arising from or related to this warranty
policy shall be in the State of California and no legal action shall be commenced
elsewhere.
This limited warranty begins on the date of the customer purchase and is valid and
available to the original purchaser only. Mytee products are for commercial use only
and are not intended for personal, family or household uses.
Return Material Authorization Procedure
HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY,
EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY.
THERE ARE NO WARRANTIES, WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE
PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES
NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF MYTEES GOODS. THIS LIMITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT
ANY TIME WITHOUT NOTICE.
The Distributor must follow Mytee Products, Inc. standard RMA procedure:
It is the responsibility of any Authorized Service Center (ASC) or Distributor with
written authorization to ensure the Customers equipment is repaired as soon as
possible. Only Mytee Products Inc. or it’s authorized dealers with written authorization, service centers, and agents may make warranty repairs on these products. All
others do so at their own risk and expense.
1. When a repair falls within the Warranty time period for a piece of equipment, the
Distributor will fill out a RMA/Warranty claim form. This form will act as a repair order
to replace any defective parts.
2. All defective parts must be returned to Mytee Products, Inc. with the RMA/claim
form for evaluation at the customer’s expense. This shipping is non-refundable. All
warranty claims are subject to an evaluation by Mytee Products, Inc. to determine if
warranty will be approved. Any credit for repair and/or parts will only be issued upon
evaluation and approval from Mytee Products, Inc.
90-DAY PARTS AND LABOR LIMITED WARRANTY: Mytee will cover parts and labor
on all components for 90 days from the date of original purchase. This warranty covers the cost of replacement and labor only, and does not cover shipping costs.
WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for
90 days from the date of original purchase. Wear parts are items which wear out
as a result of usage or the passage of time and are consumed despite attempts to
maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals,
hoses, switches, thermostats, plastisol parts, filters, bearings, brushes, solenoids, orings, bulbs, heating elements, castors, or other parts deemed wear items in Mytees
sole discretion. This warranty covers the cost of replacement only and does not cover
shipping or labor costs.
3. When Warranty is approved, the Distributor’s account will be credited for the
replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s)
to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be
credited for any parts sent for this claim.
1-YEAR MAJOR COMPONENTS WARRANTY: Mytee warrants that pumps, vacuum
and floor machine motors, and heaters are covered for a one (1) year limited warranty from the date of original purchase. This warranty does not apply and is void if
the pump, vacuum motor, or heater has worn brush motors, water damage, chemical
build-up, chemical damage, or evidence of abuse, neglect or tampering. This warranty covers the cost of replacement only, and does not cover shipping or labor costs.
HOUSING LIFETIME LIMITED WARRANTY: Mytee warrants that all rotationally
molded housing and tanks will be free from manufacturing defects, defects in workmanship, and defects in material for the life of the part. Replacement cost does not
include the cost of shipping or labor.
LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR
OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE REMEDY UNDER
ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO
EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES.
All limited warranties are void for, and Mytee does not warrant in any way, any product that evidences misapplication, improper installation, abuse, lack of maintenance,
negligence in use or care, abnormal use, alteration of design, use of incompatible
or corrosive chemicals, use in a rental service, and/or servicing, installation of parts,
or repairs by anyone other than Mytee or a Mytee authorized distributor or service
center. Mytee may make changes in products it manufactures and markets at any
time; these changes are made without obligation to change, retrofit, or upgrade any
product previously sold or manufactured.
Mytee has no obligation to honor the limited warranties set forth herein unless the
original purchaser, promptly upon discovering the warranty claim and prior to continuing to use the product, contacts Mytee or a Mytee authorized distributor or service
center to describe the claim and to receive and follow instructions for documenting
and resolving the claim. In addition, the purchaser must provide the product to which
the claim applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection.
If any provision or portion of this limited warranty policy is found to be unenforceable,
then the remaining provisions and portions shall remain valid and enforceable.
If any provision or portion of this limited warranty policy is found to be limited by
law, then that provision or portion shall be construed to make it effective within the
bounds of law. For example, if there are legal limitations on the duration of
warranties, the warranties made herein shall be construed to have the minimum
duration required by law, or, if there are legal limitations of exclusion of remedies,
the exclusions made herein shall be construed to apply to the fullest extent possible
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising