advertisement
Vantage 17 Battery
Order Parts Here:
www.ivie-ent.com/parts
Ph:(918)254-5161
Operator’s Manual
Manuel d’utilisation
Libro de Instrucciones
READ THIS BOOK
LEA ESTE MANUAL
LISEZ CE MANUEL
EN
ES
FR
English (3 - 27)
Español (29 - 53)
Français (55 - 80)
This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it.
If your operator(s) cannot read this manual, have it explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
For new books write to: Clarke®, 2100 Highway 265, Springdale, Arkansas 72764.
Form No. 909 6772 000 - 05/2006
EN
ENGLISH
TABLE OF CONTENTS
BATTERY CHECK/SETTING ON A NEW MACHINE
(WET OR GEL) BATTERY SETTING, INSTALLATION AND CHARGING
MACHINE OPERATION (SCRUBBING/DRYING)
SQUEEGEE BLADE CHECK AND REPLACEMENT
TANK AND VACUUM GRID WITH FLOAT CLEANING OF THE
Vantage 17 Battery ACCESSORIES/OPTIONS
HOW TO CORRECT PROBLEMS IN THE MACHINE
2 Operator’s Manual - Vantage 17 Battery
ENGLISH
EN
OPERATOR SAFETY INSTRUCTIONS
DANGER!
Indicates a dangerous situation (risk of death) for the User.
WARNING!
Indicates the risk for people of being injured and for objects of being damaged.
CAUTION!
DANGER!
DANGER!
DANGER!
DANGER!
DANGER!
DANGER!
Indicates a caution or a remark related to important of useful functions. Pay particular attention to the paragraphs marked by this symbol.
This machine must be used by properly trained and authorized personnel only. Children or disabled people cannot use this machine.
When using lead (WET) batteries, battery charging produces highly explosive hydrogen gas.
During battery charging, remove the recovery tank assembly and perform this operation in well-ventilated areas and away from naked flames. Do not smoke near the machine while charging the batteries.
When using lead (WET) batteries, keep sparks, flames and incandescent materials away from the batteries. During normal operation, explosive gases are released.
Do not operate the machine near toxic, dangerous, inflammable and/or explosive powders, liquids or vapours.
Disconnect the batteries before performing any maintenance/repair procedure.
Do not wear jewels when working near electrical components.
WARNING!
Before connecting the battery charger to the electrical mains, be sure that frequency and voltage indicated in the related Manual correspond to the mains voltage.
WARNING!
WARNING!
Do not charge batteries with damaged battery charger cable or plug. If the machine is not working as it should, has been damaged, left outdoors or dropped into water, return it to the Service
Center.
Do not pull or carry the machine by the battery charger cable; never use the battery charger cable as a handle. Do not close a door on the supply cable, or pull the supply cable around sharp edges or corners. Do not run the machine on the battery charger cable.
Keep the battery charger cable away from heated surfaces.
WARNING!
To reduce the risk of fire, electric shock, or injury, do not leave the machine unattended when it is plugged in.
WARNING!
To avoid electric shock, do not expose to rain. Store the machine indoors.
WARNING!
Do not allow to be used as a toy. Close attention is necessary when used near children.
WARNING!
Use only as described in this Manual. Use only Clarke recommended accessories.
WARNING!
WARNING!
Take all necessary precautions to prevent hair, jewerly and loose clothing from being caught in the machine moving parts or vacuuming parts of the machine.
Do not leave the machine unattended without being sure that the machine cannot move independently.
Operator’s Manual - Vantage 17 Battery 3
EN
ENGLISH
4
WARNING!
Do not use the machine on slopes with a gradient exceeding the specifications.
WARNING!
WARNING!
Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged; always keep the openings free from dust, hair and any other foreign material which could reduce the air flow.
While using this machine, take care not to cause damage to people.
WARNING!
Do not use the machine in particularly dusty areas.
WARNING!
Do not put any can containing fluids on the machine.
WARNING!
WARNING!
WARNING!
The machine working temperature must be between +32°F and +104°F (0°C and +40°C).
The storage temperature must be between +32°F and +104°F (0°C and +40°C).
The humidity must be between 30% and 95%.
Always protect the machine against the sun, rain and bad weather, both under operation and inactivity condition.
Do not use the machine as a means of transport.
WARNING!
Do not use the machine on slopes with an inclination higher than 2%.
WARNING!
Do not allow the brush to operate while the machine is stationary to avoid damaging the floor.
WARNING!
Do not bump into shelves or scaffoldings, particularly where there is a risk of falling objects.
WARNING!
Do not tamper with the machine safety guards and follow the ordinary maintenance instructions.
WARNING!
Do not remove or modify the plates affixed to the machine.
WARNING!
In case of fire, use a powder fire extinguisher, not a water one.
WARNING!
To ensure the proper and safe operation of the machine, have the scheduled maintenance and repair, detailed in the relevant chapter of this Manual, performed by the authorized personnel or an authorized Service Center.
WARNING!
If parts must be replaced, require GENUINE spare parts from a Dealer or Authorized Retailer.
WARNING!
Do not wash the machine with direct or pressurised water jets, or with corrosive substances.
WARNING!
WARNING!
WARNING!
The machine must be disposed of properly, because of the presence of toxic-harmful materials
(batteries, electronic boards etc.), which are subject to standards that require disposal in special centers (see Scrapping chapter).
If the machine is used according to the instructions, the vibrations do not cause dangerous situations. The machine vibration level is under 98.42 in/s2 (2.5 m/s2).
Pay attention during the machine transfers when temperature is below freezing point. The water in the recovery tank or in the hoses could freeze and seriously damage the machine.
Operator’s Manual - Vantage 17 Battery
ENGLISH
EN
WARNING!
CAUTION!
Use the brushes and the pads supplied with the machine and those specified in the Operator’s
Manual. Using other brushes or pads could reduce safety.
This machine contains lead acid batteries. The batteries must be disposed of in an environmentally acceptable manner.
Operator’s Manual - Vantage 17 Battery 5
EN
ENGLISH
INTRODUCTION
The model of the Clarke scrubber-dryer ensures a highly effective floor cleaning performance. The Vantage 17 Battery model uses a single rotary brush to clean an area of 17.0 in (430 mm) in width. The rear squeegee performs the floor cleaning and the vacuum system recovers the washing water in a single pass.
HOW TO KEEP THIS MANUAL
The Instructions for Operator’s Manual must be kept near the machine, inside an adequate case, away from liquids and other substances that can cause damage to it.
IDENTIFICATION DATA
The machine model year is written in the Declaration of Conformity and it is also indicated by the first two figures of the machine serial number.
This information is useful when requiring machine spare parts. Use the following table to write down the machine identification data for any further reference.
MACHINE Model: ______________________________
MACHINE Serial Number: _______________________
CHANGES AND IMPROVEMENTS
Clarke constantly improves its products and reserves the right to make changes and improvements at its discretion without being obliged to apply such benefits to the machines previously sold.
Any change and/or addition of accessories must be approved and performed by Clarke.
UNPACKING
To unpack the machine carefully follow the instructions on the packing.
When the machine is delivered, check that the packing and the machine were not damaged during transportation. In case of visible damages, keep the packing and have it checked by the Carrier that delivered it. Call the Carrier immediately to fill in a damage claim.
Please check that the following items have been supplied with the machine:
1.
Technical documents:
– Scrubber-dryer operator's manual
– Electronic battery charger manual
2.
40A fuse
3.
battery panels
6 Operator’s Manual - Vantage 17 Battery
ENGLISH
EN
MACHINE SPECIFICATIONS
Model
Working Voltage
Standard Batteries (Quantity: 2)
Battery rating (80 Ah)
Drive Speed
Battery Protection System
Vacuum Motor
Vacuum System Capacity
Solution Tank Capacity
Solution Flow (min/max)
Recovery Tank Capacity
Squeegee
Squeegee Width
Cleaning Width
Brush/Pad Motor
Brush/Pad Diameter
Brush/Pad Rotation Speed
Brush/Pad On-Floor Pressure (with Full Tank)
Central Wheels on Fixed Axle Diameter
Pivoting Wheel (diameter)
Wheel Pressure on the Ground
On-Board Battery Charger
Maximum Floor Inclination
Machine Length
Machine Width (without Squeegee)
Machine Height
Machine Weight with Batteries, Brush and Full Solution
Tank (Working Condition)
Sound Pressure Level (at the Operator's Position)
Battery Compartment Size (Length x Width x Height)
Vantage 17 Battery
24 V
12V 70 Ah, GEL
20 hr
Determined by brush rotation
Low Voltage Cut-Off of Brush and Solution
330 W
41.5 in H2O (1,055 mm H
2
O)
8.2 gal (31 liters)
0.08/0.26 gal/min (0.3/1.0 liters/min)
7.7 gal (29 liters)
Straight
28.3 in (720 mm)
17 in (430 mm)
520 W
17 in (430 mm)
135 RPM
50.6 lbs (23 kg)
9.8 in (250 mm)
1.9 in (49 mm)
Less than 0.37 ft/lbs2 (0.5 N/mm
2
)
24V D.C., 8 Amp., 115-230V, 50-60 Hz
2 %
43.9 in (1115 mm)
22.4 in (570 mm)
41.4 in (1050 mm)
346.1 lbs (157 kg)
67 dB(A)
13.8x13.8x10.2 in (350x350x260 mm)
Operator’s Manual - Vantage 17 Battery 7
EN
ENGLISH
MACHINE TRANSPORT PROCEDURES
How to Load and Unload the Machine from a Van or a
Truck
WARNING!
This machine is heavy. Machine transfer must be performed by qualified personnel only. Machine transfer on steep ramps must be performed by two well-trained operators only. Always move it slowly.
Do not turn the machine on slopes. Do not leave the machine unattended on slopes. Loading ramp width must not be less than 40 in (1 m).
1.
Check that the loading ramp is not longer than 8 feet (2.5
m) and not wider than 40 inches (1 m). Its thickness must be adequate to support the machine and operators' weight.
2.
Check that the ramp is dry and clean.
3.
Position the ramp properly.
4.
Before loading the machine, remove the squeegee assembly and the brush/pad holder. Before loading the machine, empty both the solution and the recovery tank.
How to Fasten the Machine Inside the Vehicle
5.
Clarke recommends tying down machine when transporting.
Figure 1
8 Operator’s Manual - Vantage 17 Battery
ENGLISH
EN
SYMBOLS SHOWN ON THE MACHINE
WARNING!
Carefully read all maintenance/repair instructions before performing any maintenance/repair procedure.
WARNING!
Do not wash the machine with pressurized water.
WARNING!
Do not open the cover. Electric danger!
Operator’s Manual - Vantage 17 Battery 9
EN
ENGLISH
MACHINE DESCRIPTION
OUTER STRUCTURE
(See Fig. 2)
A.
Serial number plate/technical data
B.
Handlebar
C. Control panel
D. Solution flow control lever
E1. ECO Solution Flow Position
E2. Maximum solution flow position
F.
Recovery tank cover
G. Rear support wheel for transport/parking
H. Central wheels on fixed axle
I.
Brush/pad-holder with pad
J.
Brush/pad-holder cover
K.
Squeegee
L.
Squeegee knobs
M. Front squeegee blade
N. Rear squeegee blade
O. Squeegee blade fixing springs
P.
Recovery tank drain hose
Q. Recovery tank drain hose bracket
R. Solution drain valve
S.
Squeegee lifting/lowering lever
T.
Solution filter
U. Battery charger cable
V.
Squeegee vacuum hose
W. Transport/parking device
W1. Transport/parking device activated
W2. Transport/parking device deactivated
X.
Transport/parking device positioning pin
Y.
Electrical component box
Z.
Battery charger
AA. Battery charger warning lights
AB. Battery installation diagram
AC. Recovery tank
AD. Solution tank
W1
10
AD
X
AC
R
W
W2
J
I
F C S
B
A
U
E2
E1
Z
Y
Q
P
AB
AA
V L
H T
M
D G
N
O
K
O
M
Figure 2
N
Operator’s Manual - Vantage 17 Battery
ENGLISH
EN
INNER STRUCTURE
(See Fig. 3)
A.
Recovery tank cover (open)
B.
Recovery tank cover gasket
C. Cover stand (applied)
D. Recovery tank
E.
Solution tank
F.
Vacuum grid with automatic shut-off float
G. Recovery water drain hole
H. Vacuum motor
I.
Brush/pad motor
J.
Batteries
K.
Battery installation diagram
L.
Cover with brush/pad-holder coupling pin
M. Machine speed adjusting screw
N. Brush
O. Pad-holder
P.
Pad
Q. Vent hole
K
J
Q
F
G
H
L
M
Operator’s Manual - Vantage 17 Battery
Figure 3
I
N
A
B
C
D
E
O
P
11
EN
ENGLISH
CONTROL PANEL
(See Fig. 4)
Charged Battery Indicator Light (Green) (A, Fig. 4)
When it turns on, it indicates that the batteries are charged.
Half-discharged Battery Indicator Light (Yellow) (B, Fig. 4)
When it turns on, it indicates that the batteries are half discharged.
Discharged Battery Indicator Light (Red) (C, Fig. 4)
When it turns on, it indicates that the batteries are discharged. Do not use the machine with discharged batteries, to avoid damaging the batteries, but charge them (see the procedure in the Maintenance chapter).
Brush/Pad Rotation Switch (D, Fig. 4)
When it is turned to the "I" position, the machine is ready to start the brush/pad rotation. To start the brush/pad rotation, press and hold one or both the activation switches (F, Fig. 4).
When it is turned to the "0" position, the brush/pad rotation is deactivated.
Water Vacuuming Switch (E, Fig. 4)
When it is turned to the "I" position, it starts the vacuuming of the recovery water.
When it is turned to the "0" position, it stops the vacuuming of the recovery water.
Activation Switches (F, Fig. 4)
When one or both the activation switches are pressed, the brush/pad rotation is activated.
The switches are active only if the brush/pad rotation switch (D, Fig. 4) is turned to the "I" position.
A
F
B
C
12
F
Figure 4
D
E
Operator’s Manual - Vantage 17 Battery
USE
WARNING!
On some points of the machine there are some labels indicating:
– DANGER
– WARNING
– CAUTION
– INFORMATION
While reading this Manual, the Operator must pay particular attention to the symbols shown in the plates.
Do not cover these plates for any reason and immediately replace them if damaged.
BATTERY CHECK/SETTING ON A NEW MACHINE
WARNING!
The electric components of this machine can be seriously damaged if batteries are either installed or connected improperly. The batteries must be installed by qualified personnel only.
Check the batteries for damage before installation.
Handle the batteries with great care.
Install the battery terminal caps supplied with the machine.
The machine is supplied with GEL batteries already installed and ready to be used.
– Turn the brush/pad rotation switch and the water
– vacuuming switch (A and B, Fig. 6) to the "I" position. If the green warning light (C) turns on, the batteries are ready to be used.
If the yellow or red warning light (D or E, Fig. 6) turns on, it is necessary to charge the batteries before using the machine (see the procedure in the Maintenance chapter).
B
ENGLISH
EN
A
Figure 5
C
A
B
D
E
Figure 6
Operator’s Manual - Vantage 17 Battery 13
EN
ENGLISH
(WET OR GEL) BATTERY SETTING,
INSTALLATION AND CHARGING
The electrical board of the machine is to be set according to the type of batteries installed, either gel (GEL) or lead (WET).
Proceed as follows:
Machine Setting
1.
The machine factory setting is for GEL batteries; if this setting corresponds to the type of batteries bought, go to step 5. Otherwise, carry out steps 2, 3, and 4 too.
2.
Remove the screws (A, Fig. 7) and carefully pull out the electrical component box cover (B).
3.
Push the microswitch (C, Fig. 7) downwards to WET position.
WARNING
Do not move the adjacent switch (D, Fig. 7).
4.
Reinstall the electrical component box cover (B, Fig. 7) and tighten the screws (A).
Battery Installation
5.
Disconnect the vacuum hose (A, Fig. 8) from the squeegee (B).
6.
Disconnect the recovery tank drain hose (C, Fig. 8) from the bracket (D).
7.
Open the cover (A, Fig. 9) and apply the cover stand (B).
8.
Grasp the recovery tank (C, Fig. 9) in the area (D) and lift it, as shown in the figure, then disconnect the vacuum hose (E) from the tank and remove the tank (C) together with the hoses (F) and (G).
9.
Install the batteries on the machine according to the diagram (E, Fig. 8).
10. Reinstall the tank (C, Fig. 9) by carrying out steps 5 to 9 in the reverse order.
Battery Charging
11. Charge the batteries (see the relevant procedure in the
Maintenance chapter).
D
C
A
B
A
A
A
Figure 7
Figure 8
D
C
E
A
B
D
C
E
14
G A
F
B
Figure 9
Operator’s Manual - Vantage 17 Battery
ENGLISH
EN
BEFORE MACHINE START-UP
To prepare the machine for operation, follow this procedure before start-up.
Squeegee Installation
1.
Install the squeegee (A, Fig. 10) and fix it by means of the squeegee knobs (B), then connect the vacuum hose (C) to the squeegee.
Solution Tank Filling
2.
Fill the solution tank (A, Fig. 11) with a solution suitable for the work to be carried out.
Do not fill the solution tank completely, leave few inches from the edge.
Always follow the dilution instructions on the container label on the chemical product used to create the solution.
The solution temperature must not exceed 100°F (40°C).
CAUTION
Use only low-foam and non-flammable liquid detergents, intended for automatic scrubber applications.
Brush or Pad-Holder Installation
NOTE
According to the kind of cleaning to be carried out, the machine can be equipped both with the brush (B,
Fig. 11) and the pad-holder (C) with pad (D).
3.
Deactivate the transport/parking device (A, Fig. 12) by putting it in position (B) after inserting the relevant pin (C).
4.
Lift the brush cover (D, Fig. 12) by prying the handlebar
(E).
5.
Place the brush (B, Fig. 11) or the pad-holder (C) with pad (D) under the cover.
6.
Lower the cover (D, Fig. 12) by means of the handlebar
(E).
7.
Press the brush push-button on “I” (Fig. 12, F), then press on or both push-buttons (Fig. 12, G) for a few seconds.
If the hooking operation is difficult, manually rotate the brush/pad-holder counterclockwise (Fig. 13).
B
C
B
Figure 10
Figure 13
Operator’s Manual - Vantage 17 Battery
C
A D
B
Figure 12
A
C
Figure 11
F
D
E
A
G
15
EN
ENGLISH
MACHINE START AND STOP
Start
1.
Prepare the machine according to the procedure shown in the previous paragraph.
2.
Lower the squeegee (A, Fig. 15) by pushing the lever (B) downwards.
3.
Turn the solution flow control lever (C, Fig. 15) to one of the following positions, according to the type of cleaning to be carried out:
– ECO system: When the lever (C, Fig. 15) is in the
"ECO" position (D), the machine works in a special condition of programmed water "economy" usage; as the water flow is set and constant, the machine can work with a cleaning time of 70-80 minutes [0.08
gal/min (0.3 liters/min].
– Variable system: When the lever is turned to the left
(variable flow), it is possible to increase the capacity up to 0.26 gal/min (1 liter/min) (E, Fig. 15).
During machine operation, it is not possible to completely close the water flow to the brush/pad.
4.
Turn the switches (A and B, Fig. 14) to the "I" position.
NOTE
If the green indicator light (C, Fig. 14) turns on, the machine is ready to be used.
If the yellow (D) or red indicator light (E) turns on, it is necessary to charge the batteries (see the procedure in the Maintenance chapter).
5.
While keeping both hands on the handlebar (G, Fig. 15), start the machine by pressing one or both the activation switches (F).
Machine Stop
6.
Release the switches (F, Fig. 15).
7.
Turn the switches (A and B, Fig. 14) to the "0" position.
8.
Lift the squeegee by pushing the lever (B, Fig. 15) completely upwards.
9.
Lift the brush/pad by activating (B, Fig. 16) the transport/parking device (A) after inserting the relevant pin (C).
E
D
C
Figure 15
C
D
E
Figure 14
G
A
B
F
B
F
A
C
A
16
B
Figure 16
Operator’s Manual - Vantage 17 Battery
MACHINE OPERATION (SCRUBBING/DRYING)
1.
Start the machine according to the procedure shown in the previous paragraph.
2.
While keeping both hands on the handlebar (D, Fig. 18), move the machine and start scrubbing/drying the floor.
CAUTION:
To avoid damaging the floor surface:
– Do not use the brush/pad without the solution.
– When the machine is stopped, stop the brush/pad by releasing the switches (A, Fig. 18).
CAUTION:
Before lifting the brush/pad, stop its rotation by releasing the switches (A, Fig. 18).
3.
If necessary, adjust the solution flow sent to the brush/pad by turning the lever (B, Fig. 18).
Battery Discharge During Operation
4.
Until the green indicator light (A, Fig. 17) stays on, the batteries allow the machine to operate normally.
When the green indicator light (A) turns off and the yellow
(B) and red (C) warning indicator lights turn on in sequence, it is necessary to charge the batteries.
CAUTION:
Do not use the machine with discharged batteries, to avoid damaging the batteries and reducing the battery life.
Machine Speed Adjustment
5.
The machine speed depends on the type of floor to be cleaned and on the choice of using brush or pad.
If necessary, it is possible to adjust the machine speed by following the relevant procedure in the Maintenance chapter.
MACHINE TRANSPORT/PARKING
After operation, proceed as follows to transport/park the machine.
1.
Turn the brush/pad rotation switch and the water vacuuming switch (D and E, Fig. 17) to the "0" position.
2.
Lift the squeegee by pushing the lever (C, Fig. 18) upwards.
3.
Grasp the handlebar (A, Fig. 19) and slightly lower it until the rear wheel (B) comes into contact with the floor, as shown in the figure. While holding the machine in this position, push it to the transport/parking area.
Figure 17
D
B
Figure 18
ENGLISH
EN
A
A
B
C
D
E
C
A
A
B
Figure 19
Operator’s Manual - Vantage 17 Battery 17
EN
ENGLISH
TANK EMPTYING
An automatic float shut-off system (A, Fig. 20) deactivates the vacuum system once the recovery tank (B) is full.
The vacuum system shutdown is due to the recovery tank filling, which prevents recovery water from being vacuumed, and it is signalled by a sudden increase in the system motor noise frequency.
When the recovery tank (B, Fig. 20) is full, empty it according to the following procedure.
Recovery Tank Emptying
1.
Stop the machine by turning the brush/pad rotation switch and the water vacuuming switch (A and B, Fig. 21) to the "0" position.
2.
Lift the squeegee by means of the lever (C, Fig. 21).
3.
Push the machine to the appointed disposal area.
4.
Insert the positioning pin (E), lift the brush/pad and activate the transport/parking device (D, Fig. 21) by means of the handlebar.
5.
Disconnect the recovery tank drain hose (F, Fig. 21) from the bracket (G); open the cover (H), then lower the hose
(F) and empty the recovery tank. Then, rinse the tank with clean water.
Solution Tank Emptying
6.
Carry out steps 1 to 4.
7.
Empty the solution tank by opening the drain valve (I, Fig.
21). Then, rinse the tank with clean water.
AFTER USING THE MACHINE
After scrubbing-drying, before leaving the machine:
1.
Remove the brush/pad-holder as follows:
– Turn the brush/pad rotation switch (A, Fig. 21) to the
"I" position.
– Lift the brush/pad-holder and press one or both the switches (J, Fig. 21) for a few seconds, then release them: this causes the brush/pad-holder to be disengaged.
2.
Empty the tanks (B and C, Fig. 20) according to the procedure shown in the previous paragraph.
3.
Perform the maintenance operations to be carried out after using the machine (see the Maintenance chapter).
4.
Store the machine in a clean and dry place, with the brush/pad and the squeegee lifted or removed.
A
18
B
C
E
D
I
Figure 20
A
B
J
C
H
G
F
K
L
Figure 21
Operator’s Manual - Vantage 17 Battery
RECOVERY TANK REMOVAL
To check the batteries, or to perform other operations, it may be necessary to remove the recovery tank (A, Fig. 23) according to the following procedure:
1.
Empty the tank (A, Fig. 23) according to the procedure shown in the relevant paragraph.
2.
Drive the machine on a level ground.
3.
Make sure that the switches (A and B, Fig. 22) are in the
"0" position.
4.
Disconnect the vacuum hose (C, Fig. 22) from the squeegee (D).
5.
Disconnect the recovery tank drain hose (E, Fig. 22) from the bracket (F).
6.
Open the cover (B, Fig. 23) and apply the cover stand
(C).
7.
Grasp the recovery tank (A, Fig. 23) in the area (D) and slightly lift it, as shown in the figure.
8.
Disconnect the vacuum hose (E, Fig. 23) from the tank, then remove the tank (A) with the hoses (F) and (G).
STORED MACHINE
If the machine is not going to be used for more than 30 days, proceed as follows:
1.
Perform the operations described in the After Using the
Machine paragraph.
2.
Remove the recovery tank (A, Fig. 23) according to the procedure shown in the previous paragraph, then disconnect the battery negative terminals.
3.
Reinstall the recovery tank (A, Fig. 23).
4.
Store the machine in a clean and dry place, with the brush/pad and the squeegee lifted or removed.
A B
A
E
Figure 22
D
ENGLISH
EN
C
D
F
E
G B
F
C
Figure 23
Operator’s Manual - Vantage 17 Battery 19
EN
ENGLISH
MAINTENANCE
WARNING!
All maintenance operations must be performed by qualified personnel, or by an authorized Service Center.
WARNING!
Maintenance operations must be carried out:
– With the machine switched off
– With the battery disconnected
– With the battery charger-electrical mains connecting cable disconnected
Moreover, read carefully the instructions in the Operator Safety Instructions chapter before performing any maintenance operation.
The lifespan of the machine and its maximum operating safety are ensured by correct and regular maintenance.
Provided below is the Scheduled Maintenance Table. The intervals shown may vary according to particular working conditions, which are to be defined by the person in charge of the maintenance.
This Manual contains the Scheduled Maintenance Table and describes only the easiest and most common maintenance procedures.
SCHEDULED MAINTENANCE TABLE
Procedure
Squeegee Cleaning
Brush Cleaning
Tank and Vacuum Grid with Float Cleaning
Battery Charging
Squeegee Blade Check and Replacement
Solution Filter Cleaning
Screw and Nut Tightening Check
Brush Motor Carbon Brush Check or Replacement
Vacuum Motor Carbon Brush Check or Replacement
Daily or after using the machine z z z z
Weekly
(1): and after the first 8 working hours
(2): for these maintenance operations, contact an authorized Clarke Service Center z z
Every six months z (1)
Yearly z (2) z (2)
20 Operator’s Manual - Vantage 17 Battery
A B
ENGLISH
EN
SQUEEGEE CLEANING
NOTE
The squeegee must be clean and the blades must be in good condition in order for the floor to dry properly.
CAUTION
It is advisable to use protective gloves when cleaning the squeegee because there may be cutting debris.
1.
Make sure that the switches (A and B, Fig. 24) are in the
"0" position.
2.
Lower the squeegee (D, Fig. 24) by means of the lever
(C).
3.
Disconnect the vacuum hose (E, Fig. 24) from the squeegee.
4.
Loosen the squeegee knobs (F, Fig. 24) and remove the squeegee (D).
5.
Wash and clean the squeegee assembly to remove dirt and debris.
6.
Check the front blade (C, Fig. 25) and the rear blade (D) for wear, cuts and tears; if required, replace them according to the procedure in the “Squeegee Blade
Check and Replacement“ section below.
7.
Reassemble in the reverse order of disassembly.
SQUEEGEE BLADE CHECK AND REPLACEMENT
1.
Clean the squeegee according to the procedure shown in the previous paragraph.
2.
Check that the edge (E, Fig. 25) of the front blade and the edge (F) of the rear blade lay down on the same level, along their length; otherwise adjust their height according to the following procedure:
– Remove the fixing springs (G, Fig. 25) and adjust the front blade (C) and the rear blade (D).
– Reinstall the fixing springs on the properly adjusted front and rear blades.
3.
Check the front blade (C, Fig. 25) and rear blade (D) for wear, cuts and tears. If necessary, replace them according to the following procedure:
– Remove the spring clamp (G, Fig. 25) and replace the blade.
NOTE: When replacing the blades, make sure that the ribs of the front blade face the front and the ribs of the rear blade face the rear.
– Reinstall the spring clamps (G, Fig. 25).
4.
Reinstall the squeegee (D, Fig. 24) and screw down the squeegee knobs (F).
5.
Connect the vacuum hose (E, Fig. 24) to the squeegee
(D).
E
C
A
G
B
Figure 24
F
A
G
D
C
D
C
E
H F
Figure 25
I
D
Operator’s Manual - Vantage 17 Battery 21
EN
ENGLISH
BRUSH CLEANING
CAUTION
It is advisable to use protective gloves when cleaning the brush because there may be cutting debris.
1.
Remove the brush from the machine, according to the procedure shown in the Use chapter.
2.
Clean and wash the brush with water and detergent.
3.
Check the brush bristles for integrity and wear; if necessary, replace the brush.
CLEANING OF THE TANK AND VACUUM GRID
FLOAT
1.
Push the machine to the appointed disposal area.
2.
Make sure that the switches (A and B, Fig. 26) are in the
"0" position.
3.
Lift the cover (A, Fig. 27) and apply the cover stand (B), then clean and wash the cover, the tanks (C and D) and the vacuum grid (E) with clean water.
Drain the water from the tanks by means of the drain hose (C, Fig. 26) and valve (D).
4.
If necessary, release the retainers (F, Fig. 27), open the vacuum grid (E), remove the float (G), then carefully clean and reinstall them.
5.
Check the cover sealing gasket (H, Fig. 27) of the recovery tank for wear.
NOTE
The gasket (H, Fig. 27) creates vacuum in the tank, which is necessary for the vacuuming of the recovery water.
If necessary, replace the gasket (H, Fig. 27) after removing it from the housing (I).
When reassembling the new gasket, install the joint (J) in the central area, as shown in Fig. 27.
6.
Check the gasket (H, Fig. 27) seating surface (K) for integrity and sealing capabilities.
7.
Check the vent hole (L, Fig. 27). If clogged, clean it.
NOTE
The hole (L, Fig. 27) compensates the air in the cover interspaces, thus allowing the creation of vacuum in the recovery tank.
8.
Remove the cover stand (B, Fig. 27) and close the cover
(A).
I
H
D
A
Figure 26
H
G
E
F
J
K
B
A B
F
C
C
D
L
22
Figure 27
Operator’s Manual - Vantage 17 Battery
SOLUTION FILTER CLEANING
1.
Empty the solution tank (A, Fig. 28) according to the procedure shown in the relevant paragraph.
2.
Drive the machine on a level ground.
3.
Make sure that the switches (B and C, Fig. 28) are in the
"0" position.
4.
Remove the transparent cover (D, Fig. 28) and the filter strainer (E), then clean and reinstall them on the support
(F).
NOTE
Properly install the strainer (E, Fig. 28) in the housing (G) of the support (F).
MACHINE SPEED ADJUSTMENT
NOTE
The machine speed depends on the type of floor to be cleaned and on the choice of using brush or pad.
The machine speed can be adjusted according to the following procedure.
1.
Remove the recovery tank as shown in the Use chapter.
2.
Adjust the machine speed by means of the screw (A, Fig.
29), according to the following procedure:
– Loosen the screw (B, Fig. 29) on the right side of the machine, by turning it counter-clockwise.
– Turn the adjusting screw (A, Fig. 29) counter-clockwise to increase the machine speed.
– Turn the adjusting screw (A, Fig. 29) clockwise to decrease the machine speed.
– After adjusting, tighten the screw (B, Fig. 29).
3.
Install the recovery tank as shown in the Use chapter.
4.
With the machine ready to operate, carry out hands-on tests of the machine speed and, if other adjustments are necessary, repeat steps 1 to 4.
A
E
D
F
ENGLISH
EN
B C
Figure 28
G
E
A
Operator’s Manual - Vantage 17 Battery
B
Figure 29
23
EN
ENGLISH
BATTERY CHARGING
NOTE
Charge the batteries when the indicator light (A or B,
Fig. 30) turns on, or when finished cleaning.
Keeping the batteries charged makes them last longer.
CAUTION
When the batteries are discharged, charge them as soon as possible, as that condition makes them last shorter.
Check for battery charge at least once a week.
CAUTION!
Batteries must be charged indoors, in a dry environment.
1.
Drive the machine indoors, in a dry environment (damp free), to charge the batteries.
2.
Charge the batteries according to the following procedure.
Figure 30
A
B
24 Operator’s Manual - Vantage 17 Battery
3.
Make sure the battery charger cable is plugged into an electrical outlet that will provide voltage and frequency according to the serial number plate/technical data (D,
Fig. 31).
NOTE
When the battery charger is connected to the electrical outlet, all machine functions are automatically cut off.
The green indicator light (B, Fig. 31) flashes when the battery charger is charging the batteries.
4.
When the green indicator light (B, Fig. 31) stays on, the battery charging cycle is over.
5.
When the battery charging cycle is over, disconnect the battery charger cable (A, Fig. 31) from the electrical outlet and wind it around it’s housing on the machine.
6.
Now the machine is ready to be used.
NOTE
For further information about the operation of the battery charger (C, Fig. 31), see the relevant Manual.
FUSE CHECK/REPLACEMENT
1.
Remove the recovery tank as shown in the Use chapter.
2.
Disconnect the battery negative terminal.
3.
Remove the screws (A, Fig. 32) and remove the electrical component box cover (B).
4.
Check/replace the fuses:
– Brush fuse (C, Fig. 32): (40 A)
– Vacuum system fuse (D, Fig. 32): (40 A)
– Solenoid valve and electronic board fuse (E, Fig. 32):
(5 A)
5.
Reassemble in the reverse order of disassembly.
D
A
Figure 31
ENGLISH
EN
B
A
C
E
D
C
B
A
Figure 32
Operator’s Manual - Vantage 17 Battery 25
EN
ENGLISH
Vantage 17 Battery ACCESSORIES/OPTIONS
In addition to the standard components, the machine can be equipped with the following accessories/options, according the machine specific use:
For further information concerning the above-mentioned optional accessories, contact an authorized Retailer.
ACCESSORIES/OPTIONS
See “Parts List” section.
909 5691 000 Brush, 17" Midlite Grit 180
08812891 Brush, 17" Poly
909 5695 000 Pad Holder 410
08603966 Ring Nylon
26 Operator’s Manual - Vantage 17 Battery
ENGLISH
EN
HOW TO CORRECT PROBLEMS IN THE MACHINE
PROBLEM
The motors do not work
Vacuum motor does not run.
Insufficient recovery water vacuuming
POSSIBLE CAUSE ACTION
Disconnected or dirty battery terminals Connect or clean the battery terminals
Completely discharged batteries
Blown fuse
Charge the batteries
Replace the fuse
Full recovery tank
Clogged vacuum grid or stuck closed float
Empty the tank
Clean the vacuum grid and the float
Vacuum hose disconnected from the squeegee or faulty
Dirty squeegee, or worn or damaged squeegee blades
Improperly closed recovery tank cover or worn gasket or clogged vent hole
Connect or repair/replace it
Clean the squeegee or replace the blades
Correctly close the cover or replace the gasket or clean the vent hole
Insufficient solution flow to the brushes
Dirty solution filter
Clogged recovery tank output hole
Clean the filter
Clean the hole
The squeegee leaves lining on the floor streaks.
Debris under the squeegee blades Remove the debris
Worn, chipped or torn squeegee blades Replace the blades
Operator’s Manual - Vantage 17 Battery 27
Vantage 17 Battery
Form No. 909 6772 000 - 05/2006
Parts List
[] = Not shown
* = optional
# = Modified item No. or New item No.
xxxxx = Contained in a Kit
Printed in Italy
Vantage 17 Battery
Solution Tank
82
7
35
17
14
36
8
15
10
31
19 11
24
34
13
9
32
21
38
16
29
37
2
3
30
28
25
27
23
4
22
26
1
18
20
39
5
6
33
12
Parts list - Vantage 17 Battery
Vantage 17 Battery
Ref.
9
10
11
12
13
14
7
8
5
6
3
4
1
2
Part No.
xxxxxxxx xxxxxxxx xxxxxxxx
088603258 xxxxxxxx xxxxxxxx
08603845 xxxxxxxx
08812392 xxx xxxx xxx xxxxxxxx xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx
15
16
17 xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx
30
31
32
33
26
27
28
29
22
23
24
25
18
19
20
21
34
35
36
37
909 6821 000
909 6437 000 xxx xxxx xxx
909 5286 000
38
39 xxx xxxx xxx
909 6441 000
[40] 909 6438 000 xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx
909 5560 000
909 5606 000
909 5641 000
909 5649 000
909 5658 000
909 5696 000
909 5748 000
909 5895 000
909 6271 000
909 6281 000
909 6283 000
Solution Tank
Description
Washer flat 6X18 (Solution tank hardware kit)
Clamp (Solution tank hardware kit)
Screw M5X10 (Solution tank hardware kit)
Washer flat 11X16
Nut hex. low self lock M6 SS (Kit squeegee lift cable)
Washer flat 6X18 SS (Kit squeegee lift cable)
Cable clamp
Knob (Kit squeegee lift cable)
Spacer
Ball joint (Kit squeegee lift cable)
Hose clamp (Solution tank hardware kit)
Screw hex hd M6X20 SS (Kit squeegee lift cable)
Screw M8X20 (Solution tank hardware kit)
Washer flat 8X17 (Kit squeegee lift cable - Solution tank hardware kit)
Washer flat 6X12,5 (Kit squeegee lift cable - Solution tank hardware kit)
Retaining ring (Solution tank hardware kit)
Nut hex. self lock M8 (Kit squeegee lift cable - Solution tank hardware kit)
Washer split (Solution tank hardware kit)
Screw M5X12 (Solution tank hardware kit)
Screw hex hd M6X16 (Solution tank hardware kit)
Washer flat 16X30 (Solution tank hardware kit)
Nut hex. self lock M10 (Solution tank hardware kit)
Wheel
Clamp
Indexing plunger
Support
Supporting rod
Valve
Wheels shaft
Elbow 90° ø10
Solution tank
Wheel
Squeegee lifting cable (Kit squeegee lift cable)
Decal Clarke Vantage17 Battery (Kit decals)
Kit squeegee lift cable (5,6,8,10,12,14,15,17,33,36)
Squeegee lifting lever (Kit squeegee lift cable)
Gasket
Spacer (Solution tank hardware kit)
Pin 3X20
Solution tank hardware kit
(1,2,3,11,13,14,15,16,17,18,19,20,21,22,38)
2
2
1
2
1
1
1
1
1
1
1
2
1
1
1
2
6
2
1
2
1
1
1
2
3
1
Qty
1
1
2
1
2
1
1
1
1
2
5
1
2
1
Parts list - Vantage 17 Battery 83
Vantage 17 Battery
Vacuum System
84
8
6
1
4
2
9
7
5
3
Parts list - Vantage 17 Battery
Vantage 17 Battery
Ref.
Part No.
7
8
5
6
3
4
1
2
08228600
08603706
909 5371 000
909 5198 000
909 5564 000
909 5565 000
909 5713 000
909 6290 000
9 146 0104 00
[10] 909 5987 000
Vacuum System
Description
Washer falt 6x18 (Vacuum systems hardware kit)
Screw cyl hd M6x12 (Vacuum systems hardware kit)
Carbon brush
Vibration damping M6
Pipe acoustic insulation
Pipe acoustic insulation
Kit vacuum motor with connector
Vacuum motor hose
Hose clamp
Vacuum systems hardware kit (1,2)
Qty
1
1
1
1
1
1
2
3
15
3
Parts list - Vantage 17 Battery 85
86
21
Vantage 17 Battery
Recovery Tank
12
17
10
2
3
1
6
4
20
16
15
18
19
7
9
11
5
14
13
8
Parts list - Vantage 17 Battery
Vantage 17 Battery
Ref.
Part No.
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
17
18
19
20 xxx xxxx xxx
145 1756 000
909 6473 000
909 6575 000
21 xxx xxxx xxx
[22] 909 5988 000
08603689
56324497
56391690
08812968
145 0543 000
145 4618 000
145 9960 000
146 2511 000
909 6199 000
909 6268 000
909 6272 000
909 6273 000
909 6289 000
909 6291 000
909 6762 000
08603935
Recovery Tank
Description
Washer flat 6X18 SS (Recovery tank hardware kit)
Float cage
Floating ball
Gasket
Hose clamp 14/32-52 (Recovery tank hardware kit)
Nut cap M6 SS (Recovery tank hardware kit)
Nut hex M6 SS (Recovery tank hardware kit)
Screw hex hd M6X40 SS (Recovery tank hardware kit)
Holder, float cage
Gasket 1370 mm
Recovery tank
Tank cover
Vacuum hose
Drain hose
Lever for fixing cover
Black cap
Decal water faucet (kit decals)
Screw 9.9x9.5 SS
Lever fixing plate
Lever fixing clamp
Decal batteries (kit decals)
Recovery tank hardware kit (1,5,6,7,8)
Qty
1
1
1
1
1
1
1
1
2
2
1
2
1
1
6
2
1
1
1
3
1
1
Parts list - Vantage 17 Battery 87
Vantage 17 Battery
Handle Assembly
88
11
13 10
12
14
1
5
7
6
8
3
9
4
2
Parts list - Vantage 17 Battery
Vantage 17 Battery
Ref.
9
10
11
12
13
14
7
8
5
6
3
4
1
2
Part No.
08812074
32400258
145 4262 000
145 9120 000
145 9237 000
909 6488 000
909 6760 000
909 6768 000
909 6774 000 xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx
11077A
Handle Assembly
Description
Screw 4.2x16 THD form
Nut M8
Cap D. 9.5
Washer flat 8x17
Washer flat 4x12
Handle bar PE
Screw pan HD PHIL M3.5X10
Harness handle cable
Pin handle bar
Switch housing (Kit push button)
Switch lever (Kit push button)
Switch (Kit push button)
Spring (Kit push button)
Kit push button (10, 11, 12, 13)
Qty
2
2
1
2
4
1
4
1
4
1
2
2
4
2
Parts list - Vantage 17 Battery 89
Vantage 17 Battery
Control Panel Assembly
90
2
5
1
6
3
4
Parts list - Vantage 17 Battery
Vantage 17 Battery
Ref.
3
4
1
2
5
6
Part No.
08603919
08812909
145 1756 000
909 5584 000
909 6275 000
909 6763 000
Control Panel Assembly
Description
Screw M3x8
Board led
Screw 2.9x9 THD FORM SS
Switch
Control panel
Decal control panel
Qty
3
2
2
1
1
1
Parts list - Vantage 17 Battery 91
Vantage 17 Battery
Solution System
26
28
5
29
9
100 mm
10 18
14
4
6
11
3
15
21
8
13
90 mm
16
12
240 mm
27
30
20
7
22
1
19
24
23
2
17
25
92 Parts list - Vantage 17 Battery
Vantage 17 Battery
Ref.
Part No.
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
21
22
23
24
17
18
19
20
909 6278 000
909 6280 000 xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx
909 5637 000
909 5651 000
25
26
27
28 xxx xxxx xxx
08603893 xxx xxxx xxx xxx xxxx xxx
29
30 xxx xxxx xxx xxx xxxx xxx
[31] 08603885
[32] 909 5977 000
[33] 909 5990 000
08601624
08603665 xxxxxxxx xxxxxxxx
08812960 xxxxxxxx xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx
146 0549 000 xxx xxxx xxx
909 5151 000 xxx xxxx xxx
909 6277 000
Solution System
Description
Rubber holder (Solenoid valve kit)
Wheel
Screw hex hd M3x12 SS (Solution systems hardware kit)
Washer flat 3x9 SS (Solution systems hardware kit)
Solenoid valve 24V (Solenoid valve kit)
Washer split 3 SS (Solution systems hardware kit)
Split pin (Solution systems hardware kit)
Screw hex hd M6x16 SS (Solution systems hardware kit)
Nut hex M6 SS (Solution systems hardware kit)
Washer flat 6x12,5 SS (Solution systems hardware kit)
Washer flat 8x17 SS (Solution systems hardware kit)
Bushing
Screw hex hd M8x55 SS (Solution systems hardware kit)
Kit water filter complete (Solenoid valve kit)
Screw M8x12 (Solution systems hardware kit)
Bracket
Support
Plate
Clamp (Solution systems hardware kit)
Screw M12x60 SS (Solution systems hardware kit)
Screw M8x55 SS (Solution systems hardware kit)
Valve (Solenoid valve kit)
Spring
Rubber holder (Solenoid valve kit)
Nut hex low self lock M8 SS (Solution systems hardware kit)
Kit filter net with gasket
Hose ø10 240 mm (Solenoid valve kit)
Hose ø10 100 mm (Solenoid valve kit)
Clamp 8/ 9-16 (Solenoid valve kit)
Hose ø10 90 mm (Solenoid valve kit)
Connector for solenoid valve
Solenoid valve kit (1,5,14,22,24,27,28,29,30)
Solution systems hardware kit
(3,4,6,7,8,9,10,11,13,15,19,20,21,25)
Qty
1
1
3
1
1
1
1
1
1
1
1
2
1
2
1
1
1
4
1
1
1
3
2
4
4
3
1
1
2
2
2
3
1
Parts list - Vantage 17 Battery 93
Vantage 17 Battery
Squeegee Assembly
94
15
12
16
3
6
5
10
11
17
4
2
7
1
13
8
14
9
Parts list - Vantage 17 Battery
Vantage 17 Battery
Ref.
1
Part No.
08812937
8
9
10
11
12
14
15
16
2
3
4
5
6
7
13
08602460
08603665
08603675
08603688
08603896
08812987
909 5554 000
909 5555 000
909 5568 000
909 5569 000
909 5607 000
08603689
08603880
909 5703 000
145 8280 000
17 909 5702 000
[18] 909 5991 000
Squeegee Assembly
Description
Spacer (Kit squeegee bumper roller - Kit squeegee complete -
Squeegee assembly hardware kit)
Bumper roller (Kit squeegee bumper roller - Kit squeegee complete - Squeegee assembly hardware kit)
Squeegee wheel (Kit squeegee wheel - Kit squeegee complete)
Nut thumb (Kit squeegee complete - Squeegee assembly hardware kit)
Nut hex low selflock M5 SS (Kit squeegee wheel - Kit squeegee complete - Squeegee assembly hardware kit)
Screw hex hd M5x45 SS (Kit squeegee wheel - Kit squeegee complete - Squeegee assembly hardware kit)
Screw M6x35 (Kit squeegee bumper roller - Kit squeegee complete - Squeegee assembly hardware kit)
Squeegee weldment (Kit squeegee complete)
Spring (Kit squeegee complete)
Blade rear (Kit squeegee complete)
Blade front (Kit squeegee complete)
Spacer (Kit squeegee wheel - Kit squeegee complete -
Squeegee assembly hardware kit)
Washer flat 6x18 SS (Kit squeegee complete - Squeegee assembly hardware kit)
Kit squeegee bumper roller (1,2,7)
Kit squeegee wheel (3,5,6,12,16)
Washer flat 5x15 SS (Kit squeegee wheel - Kit squeegee complete - Squeegee assembly hardware kit)
Kit squeegee complete (1,2,3,4,5,6,7,8,9,10,11,12,13, 16)
Squeegee assembly hardware kit (1,2,4,5,6,7,12,13,16)
2
2
2
2
2
2
2
1
1
1
1
1
4
2
1
1
6
Qty
2
Parts list - Vantage 17 Battery 95
Vantage 17 Battery
Brush System
96
29
28
3
31
32
6
4
5
12
30
13
15
26
22
23
16
11
25
7
24
20
17
1
19 21
10
2
9
14
18
27
8
Parts list - Vantage 17 Battery
Vantage 17 Battery
Ref.
Part No.
11
12
13
14
8*
8*
9
10
7
8
5
6
3
4
1
2
27
28
29
30
23
24
25
26
19
20
21
22
15
16
17
18 xxx xxxx xxx xxx xxxx xxx
909 5550 000
909 6269 000
909 6270 000
909 5558 000
909 5559 000
909 5585 000
909 5586 000
909 6217 000
909 5638 000 xxx xxxx xxx
8812589
909 5622 000 xxx xxxx xxx
8361400
31
32
146 0632 000
145 9237 000
[33] 909 5992 000 xxxxxxxx
08219000
08603849
56363855
08602461
909 5508 000 xxx xxxx xxx
909 5695 000
08812891
909 5691 000 xxx xxxx xxx xxx xxxx xxx
909 5720 000 xxxxxxxx xxx xxxx xxx xxx xxxx xxx
Brush System
Description
Nut (Brush system hardware kit)
Vibration damping
Reduction gear
Bumper roller
Spacer
Electric motor
Tab (Brush system hardware kit)
Pad driver
Brush ø430 17” Prolene PPL
Brush ø430 17” Midlite Grit180
Screw hex hd M8x12 (Brush system hardware kit)
Screw M12x55 (Brush system hardware kit)
Carbon brush set (4 pcs)
Washer flat 6x18 (Brush system hardware kit)
Screw M6x40 (Brush system hardware kit)
Screw hex hd M6x16 SS (Brush system hardware kit)
Nut hex M6 SS (Brush system hardware kit)
Screw M3x6 (Brush system hardware kit)
Brush protection
Plate brush support
Bracket
Spring
Bushing
Brush deck adjuster block
Plate
Hose copper
Reductiongearmotor 520W
Screw M6x30 (Brush system hardware kit)
Polyg.holder w.flange kit
Hose ø10 640 mm
Decal brush adjusting (Kit decals)
Nut hex M6 selflock. low
Screw hex hd M4x8
Washer flat 4x12
Brush system hardware kit (1,7,9,10,12,13,14,15,16,26)
Qty
1
1
1
1
1
1
1
1
2
2
1
2
1
1
2
1
1
2
2
1
4
1
2
1
2
1
1
1
1
1
1
1
1
1
1
Parts list - Vantage 17 Battery 97
Vantage 17 Battery
Wiring System
98 Parts list - Vantage 17 Battery
Vantage 17 Battery
Ref.
Part No.
Wiring System
Description
29
30
31
32
25
26
27
28
21
22
23
24
17
18
19
20
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
33
34
35
36
909 6288 000 xxx xxxx xxx
909 5783 000
56325755
37
38
145 8046 000
146 0660 000
[39] 909 6306 000
[40] 145 9852 000
[41] 145 3824 000
[42] 145 8513 000
[43] 909 5982 000
[44] 909 5983 000
[45] 909 5984 000
[46] 56372673
[47] 909 5955 000
[48] 145 6062 000
[49] xxx xxxx xxx
[50] xxx xxxx xxx
[51] 909 5994 000
[52] xxxxxxxx xxxxxxxx
909 6568 000 xxxxxxxx xxxxxxxxx xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx xxx xxxx xxx xxxxxxxx xxx xxxx xxx
909 6062 000 xxx xxxx xxx xxx xxxx xxx
Screw cyl hd M6x12 (Wiring system hardware kit)
Screw cyl hd M4x6 (Wiring system hardware kit)
Cover electronic card
Screw cyl hd M4x70 (Wiring system hardware kit)
Screw hex hd M3x10 (Wiring system hardware kit)
Screw hex hd M4x8 (Wiring system hardware kit)
Nut hex low M6 (Wiring system hardware kit)
Screw M8X16 (Wiring system hardware kit)
Washer flat 5x15 SS (Wiring system hardware kit)
Nut hex selflock M3 (Wiring system hardware kit)
Nut hex selflock M4 (Wiring system hardware kit)
Washer flat 8X17 (Wiring system hardware kit)
Screw hex hd M4x16 (Wiring system hardware kit)
Kit bush cable giude and retaining ring
Washer split (Wiring system hardware kit)
Washer flat 4x9 (Wiring system hardware kit) xxx xxxx xxx
146 0656 000 xxx xxxx xxx
146 0658 000
Spacer M4 (Wiring system hardware kit)
Gasket L=125 mm
Spacer hex (Wiring system hardware kit)
Screw M4x8
146 0708 000 Insulator M6 white
909 5127 000 Electromagnetic switch24V xxx xxxx xxx
146 2118 000
Dowel M6x25 (Wiring system hardware kit)
Gasket L=750 mm xxx xxxx xxx
909 5098 000
146 0719 000
909 5149 000
909 5561 000
909 6279 000
909 6427 000 xxx xxxx xxx
Screw cyl hd M5x12 SS (Wiring system hardware kit)
Electronic card
Electromagnetic switch 24V
Support battery charger cable
Battery charger 100V-230V
Bracket for battery charger
Harness electronic card
Decal tension (decals kit)
00190124
Electrical components fitting plate
Screw cyl hd M5x16 (Wiring system hardware kit)
Battery charger cable extention
Restraint
Fuse holder
Blade fuse holder
Machine harness
Blade fuse 5A
Brush Strip fuse 40A
Vaccum blade fuse 30A
Battery charger power cable
Battery charger output cable
Battery charger cooling fan
Boot battery clamps
Battery harness
Battery connector
Decal fuse 40A (decals kit)
Decal fuse 30A (decals kit)
Wiring system hardware kit
(1,2,4,5,6,7,8,9,10,11,12,13,15,16,17,19,23,25,34)
Battery 12V 70Ah
Parts list - Vantage 17 Battery
Qty
1
2
1
1
1
1
1
1
1
1
1
1
4
4
4
1
1
4
2
2
2
3
2
2
2
3
2
4
1
4
1
4
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
2
99
Vantage 17 Battery
Accessories - Pad holder kit
1
2
3
100 Parts list - Vantage 17 Battery
Vantage 17 Battery
Ref.
1
1*
1*
2*
3
Part No.
Accessories - Pad holder kit
Description
08812891
909 5691 000
909 5693 000
909 5695 000
08603966
Brush, 17”
Brush ø430 17” Midlite Grit180
Brush ø430 Prolite
Pad holder 410
Ring nylon
Qty
1
1
1
1
1
Parts list - Vantage 17 Battery 101
102
Vantage 17 Battery
Ref.
Part No.
Recommended Spare Parts
Description
[1]
[2]
[3]
[4]
909 5151 000
08603893
WEAR PARTS
Kit water filter complete
Kit filter net with gasket
909 6268 000 Gasket L = 1370 mm
909 5568 000 Blade rear
909 5569 000 Blade front [5]
[6]
[7]
909 5555 000 Spring
08812891 Brush ø430 Prolene PPL std
[8]
[9]
909 6291 0000
ORDINARY MAINTENANCE
Drain hose
909 6289 000 Suction hose
[10] 909 6290 000 Vacuum motor hose
[11] 145 0227 000
[12] 145 3824 000
[13] 145 9852 000
Blade fuse 40A
Strip fuse 40A
Blade fuse 5A
EXTRAORDINARY MAINTENANCE
[14] 08812960
[15] 909 5977 000
Solenoid valve 24V
Solenoid valve kit 24 V
[16] 909 5651 000 Rubber holder 90° for hose ø10
[17] 08601624 Rubber holder 1/4
[18] 909 5696 000 Valve
[19] 909 5713 000 Kit vacuum motor w/connector
[20] 909 5371 000 Carbon brush
[21] 909 6283 000 Squeegee lifting cable
[22] 909 6437 000 Kit squeegee lift cable
[23] 909 5564 000 Pipe acoustic insulation
[24] 909 5565 000 Pipe acoustic insulation
[25] 909 5638 000 Reductiongear motor 520W
[26] 909 5720 0000 Carbon brush set (4 pcs)
[27] 08219000 Vibration damping M8
[28] 909 5558 000 Spring
[29] 08602460 Bumper roller
[30] 909 6281 000 Wheel
[31] 909 5554 000 Squeegee weldment
[32] 909 5702 000 Kit squeegee complete
[33] 909 5703 000 Kit squeegee wheel
[34] 08603880 Kit squeegee bumper roller
[35] 909 6062 000 Kit bush cable guide and retaining ring
[36] 909 5584 000 Switch
[37] 909 5098 000 Electronic card
[38] 909 5561 000
[39] 146 0719 000
[40] 909 5127 000
[41] 00190124
Battery charger 100-230V
Electromagnetic switch 24V
Electromagnetic switch 24V
Battery 12V 70Ah
Qty
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
2
1
1
2
2
1
1
2
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
3
1
1
Parts list - Vantage 17 Battery
Vantage 17 Battery
Wiring Diagram
SW3
SW4
SW1
SW2
CH
BK BU BN OG WH PK GY
1
SC SB SV LR LY LG LC KY
8 NO Ch
Ch
Gel
Pb
Pb/Gel
SWITCH
EB1
BL
W+
W-
EB2
M1
M2
SW1
SW2
CH1
C1
EB1
EB2
LEGENDA
BATTERY CHARGER 909 5561 000
CHARGER OUTPUT CONNECTOR included in 909 5561 000
ELECTRONIC CARD (CFBA430) 909 5098 000
LED CARD (CFBALED) 08812909
ES1 BRUSH ELECTROMAGNETIC SWITCH 909 5127 000
ES2 VACUUM ELECTROMAGNETIC SWITCH 146 0719 000
ES3 CHARGER OUTPUT RELAIS included in 909 5845 000
EV1
F1
SOLENOID VALVE 08812960
BRUSH STRIP FUSE (40A) 145 3824 000
F2 VACUUM BLADE FUSE (40A) 145 0227 000
F3 WATER VALVE & ELECTR. BLADE FUSE (5A)145 9852 000
IS1 NEGATIVE INSULATOR 146 0708 000
SW3
SW4
REDUCTION GEAR MOTOR 909 5638 000
KIT VACUUM MOTOR W/ CONNECTOR 909 5713 000
BRUSH SWITCH 909 5584 000
VACUUM SWITCH 909 5584 000
RIGHT HANDLE BRUSH SWITCH
LEFT HANDLE BRUSH SWITCH
11077A
EV1
F3
BN
ES3
CFBA430 1
CT BT VT SS+ VV+ BL
8
YE BU BN BK RD
C1
YE BK RD
IS1
V-
F2
F1
BK RD BN BU
RD
OR WH
ES1
YE
GY
BU
M1
RD
ES2
BN
M2
RD
VT
WH
YE
BN
GN
GY
OG
PK
RD
COLORS CODES
BK BLACK
BU BLUE
BROWN
GREEN
GREY
ORANGE
PINK
RED
VIOLET
WHITE
YELLOW
CH1
-
-
RD
Parts list - Vantage 17 Battery 103
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement