Sharp | XL-530H | Operating instructions | Sharp XL-530H Operating instructions

XL-MP60(U) TINSEA043SJZZ
Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
MICRO COMPONENT SYSTEM
XL-MP60 Micro Component System consisting of XL-MP60 (main unit),
CP-MP60F (front speakers) and CP-MP60SW (subwoofer).
MODEL
XL-MP60
OPERATION MANUAL
04/12/24
XL-MP60(U)_FRONT.fm
TINSEA043SJZZ
1
XL-MP60
SPECIAL NOTES
Note:
Important Instruction
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
WARNING
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could
void the user's authority to operate this equipment.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
FOR YOUR RECORDS
0012
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
0012
Caution - use of controls or adjustments or performance
of procedures other than those specified herein may result in hazardous radiation exposure.
For your assistance in reporting this unit in case of loss or theft,
please record below the model number and serial number which
are located on the rear of the unit.
Please retain this information.
Model number
.......................................................
Serial number
.......................................................
Date of purchase .......................................................
Place of purchase .......................................................
0202
0012
2
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
IMPORTANT SAFETY INSTRUCTIONS
be read before the product is operated.
2 Retain Instructions - The safety and operating instructions should be
retained for future reference.
3 Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4 Follow Instructions - All operating and use instructions should be
followed.
1
10 Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on
a bed, sofa, rug, or other similar surface. This product should not be
placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have been
adhered to.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
6 Attachments - Do not use attachments not recommended by the prod-
12 Grounding or Polarization - This product may be equipped with a
uct manufacturer as they may cause hazards.
7 Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8 Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury to
a child or adult, and serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
3
11 Power Sources - This product should be operated only from the type
of power source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
5 Cleaning - Unplug this product from the wall outlet before cleaning.
2
polarized alternating-current line plug (a plug having one blade wider
than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
Alternate Warnings - This product is equipped with a three-wire
grounding-type plug, a plug having a third (grounding) pin. This plug
will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose
of the grounding-type plug.
9 A product and cart combination should be moved with
13 Power-Cord Protection - Power-supply cords should be routed so
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the product.
Important Instruction
1 Read Instructions - All the safety and operating instructions should
XL-MP60
4
5
6
7
8
14 Protective Attachment Plug - The product is equipped with an attachment plug having overload protection. This is a safety feature. See
Instruction Manual for replacement or resetting of protective device. If
replacement of the plug is required, be sure the service technician has
used a replacement plug specified by the manufacturer that has the
same overload protection as the original plug.
9
10
3
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Important Instruction
XL-MP60
IMPORTANT SAFETY INSTRUCTIONS (continued)
15 Outdoor Antenna Grounding - If an outside antenna or cable system
19 Object and Liquid Entry - Never push objects of any kind into this
is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code, ANSI/
NFPA 70, provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes, and requirements
for the grounding electrode.
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
ANTENNA LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERV ICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
NEC - NATIONAL ELECTRICAL CODE
S2898A
P OWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
16 Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning and
power-line surges.
17 Power Lines - An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be
fatal.
18 Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
20 Servicing - Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
21 Damage Requiring Service - Unplug this product from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicates a need for service.
22 Replacement Parts - When replacement parts are required, be sure
the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
23 Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
24 Wall or Ceiling Mounting - The product should be mounted to a wall
or ceiling only as recommended by the manufacturer.
25 Heat - The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
0304
4
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Contents
Accessories
! General Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 - 9
2
! Preparation for Use
System connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 12
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3
! Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
! Disc Playback
Listening to a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 - 18
Advanced disc playback . . . . . . . . . . . . . . . . . . . . . . . . . . .19 - 22
! Radio
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23, 24
Please confirm that the following accessories are included.
1
Page
! Advanced Features
Timer and sleep operation . . . . . . . . . . . . . . . . . . . . . . . . .25 - 27
Enhancing your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
! References
General Information
NOTES
Licensed under one or more of U.S. Pat. 4,972,484, 5,214,678,
5,323,396, 5,530,655, 5,539,829, 5,544,247, 5,606,618, 5,610,985,
5,740,317, 5,777,992, 5,878,080 or 5,960,037.
Supply of this product does not convey a license nor imply any
right to distribute content created with this product in revenuegenerating broadcast systems (terrestrial, satellite, cable and/or
other distribution channels), revenue-generating streaming
applications (via Internet, intranets and/or other networks), other
revenue-generating content distribution systems (pay-audio or
audio-on-demand applications and the like) or on revenuegenerating physical media (compact discs, digital versatile discs,
semiconductor chips, hard drives, memory cards and the like). An
independent license for such use is required. For details, please
visit http://mp3licensing.com.
MPEG Layer-3 audio coding technology licensed from Fraunhofer
IIS and Thomson.
XL-MP60
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29, 30
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Remote control
1 FM/AM loop antenna 1 AC power cord
(RRMCGA029SJSA)
(QANTL0009SJZZ)
4
5
6
7
8
1
(QACCU0003SJ00)
CONSUMER LIMITED WARRANTY . . . . . . . . . . . . . . . Back cover
9
Caution:
Do not use the supplied AC power cord for other equipment. Fire or
electric shock may result.
10
Note:
Only the above accessories are included.
5
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
Precautions
! General
" Please ensure that the equipment is positioned in a well-ventilated area and ensure that there is at least 4" (10 cm) of free
space along the sides, top and back of the equipment.
4" (10 cm) 4" (10 cm)
" Hold the AC power plug by the head when
removing it from the AC outlet, as pulling
the cord can damage internal wires.
" Do not remove the outer cover, as this
may result in electric shock. Refer internal service to your local SHARP service
facility.
4" (10 cm)
General Information
4" (10 cm)
" Use the unit on a firm, level surface free from
vibration.
" Keep the unit away from direct sunlight,
strong magnetic fields, excessive dust,
humidity and electronic/electrical equipment (home computers, facsimiles, etc.)
which generate electrical noise.
" Do not place anything on top of the unit.
" Do not expose the unit to moisture, to temperatures higher than
140°F (60°C) or to extremely low temperatures.
" If your system does not work properly, disconnect the AC power
cord from the AC outlet. Plug the AC power cord back in, and
then turn on your system.
" In case of an electrical storm, unplug the
unit for safety.
" This unit should only be used within the range of 41°F - 95°F
(5°C - 35°C).
Warning:
The voltage used must be the same as that specified on this unit.
Using this product with a higher voltage other than that which is
specified is dangerous and may result in a fire or other type of accident causing damage. SHARP will not be held responsible for any
damage resulting from use of this unit with a voltage other than that
which is specified.
! Volume control
The sound level at a given volume setting depends on speaker efficiency, location and various other factors. It is advisable to avoid
exposure to high volume levels, which occurs while turning the unit
on with the volume control setting up high, or while continually listening at high volumes.
6
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Controls and indicators
XL-MP60
1
! Front panel
11
3
12
13
14
15
16
17
4
5
6
7
8
18
9
! Display
10
1
2 34 5
6 7 8
9
10 11
12
13
Reference page
1. Disc Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2. Disc Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3. Disc Pause Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4. Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5. Disc Repeat Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 21
6. WMA Track Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7. CD Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8. MP3 Track Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9. Extra Bass Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
10. Sleep Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
11. Timer Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
12. FM Stereo Mode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 23
13. FM Stereo Receiving Indicator . . . . . . . . . . . . . . . . . . . . . . 23
2
3
General Information
1
2
Reference page
1. Video/Auxiliary Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14
5. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6. Disc Stop, Tuning Down Button . . . . . . . . . . . . . . . . . . 18, 23
7. Disc Play or Repeat, Tuning Up Button . . . . . . . . . 17, 21, 23
8. Extra Bass/Demo Mode Button . . . . . . . . . . . . . . . . . . 12, 14
9. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . 14
10. Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
11. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
12. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 20
13. Disc Track Down or Fast Reverse,
Tuner Preset Down Button . . . . . . . . . . . . . . . . . . . . . . . 18, 24
14. Disc Track Up or Fast Forward,
Tuner Preset Up Button . . . . . . . . . . . . . . . . . . . . . . . . . 18, 24
15. Memory/Set Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 24
16. Disc Compartment Open/Close Button . . . . . . . . . . . . . . . 17
17. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
18. Disc Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
XL-MP60(U).fm
5
6
7
8
9
10
7
05/1/28
4
TINSEA043SJZZ
XL-MP60
Controls and indicators (continued)
! Rear panel
Reference page
1. AC Power Input Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2. Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3. FM/AM Loop Antenna Jack . . . . . . . . . . . . . . . . . . . . . . . . . 11
4. Video/Auxiliary (Audio Signal) Input Jacks . . . . . . . . . . . . 28
5. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1
General Information
3
4
2
5
! Front speaker
1
2
3
1. Tweeter
2. Woofer
3. Bass Reflex Duct
4. Speaker Wire
4
! Subwoofer
1. Sub Duct Pipe
2. Subwoofer
3. Speaker Wire
2
1
3
Note:
The speaker grilles are not removable.
8
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60(U) TINSEA043SJZZ
2
XL-MP60
1
! Remote control
12
2
13
3
14
4
15
5
16
6
17
7
18
8
19
9
20
10
21
Reference page
1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 13
2. Power On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . 14
3. Direct Track Search Buttons . . . . . . . . . . . . . . . . . . . . . . . . 20
4. Disc Track Down or Fast Reverse,
Tuner Preset Down, Time Down Button . . . . . . . . . 15, 18, 24
5. Disc Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6. Extra Bass Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7. Disc Play or Repeat Button . . . . . . . . . . . . . . . . . . . . . . 17, 21
8. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 14
9. Memory/Set Button . . . . . . . . . . . . . . . . . . . 15, 22, 24, 25, 27
10. Disc Clear Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
11. CD Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
12. MP3/WMA Display Button . . . . . . . . . . . . . . . . . . . . . . . . . . 19
13. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 20
14. Disc Track Up or Fast Forward,
Tuner Preset Up, Time Up Button . . . . . . . . . . . . . . 15, 18, 24
15. Disc Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
16. Equalizer Mode Select Button . . . . . . . . . . . . . . . . . . . . . . 14
17. Disc Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
18. Timer/Sleep Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25, 27
19. Video/Auxiliary Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
20. Clock Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
21. Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2
3
General Information
1
4
5
6
7
8
11
9
10
9
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
System connections
Make sure to unplug the AC power cord before any connections.
FM/AM loop antenna connection (see page 11)
FM antenna
Front speaker (right)
Front speaker (left)
Preparation for Use
Subwoofer
AM loop antenna
AC outlet
(AC 120 V, 60 Hz)
Speaker connection (see page 11)
Connecting the AC power cord (see page 12)
10
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
! Speaker connection
! FM/AM loop antenna connection
Connect the black wire to the minus (-) terminal, and the red wire to
the plus (+) terminal.
Connect the FM/AM loop antenna to the ANTENNA jack.
Subwoofer
Front speaker
(right)
Front speaker
(left)
1
2
Position the FM antenna wire and rotate the AM loop antenna for
optimum reception. Place the AM loop antenna on a shelf, or attach
it to a stand or a wall.
Red
Black
Caution:
" Use speakers with an impedance of 6 ohms or more, as lower impedance speakers can damage the unit.
" Do not mistake the right and the left channels. The right speaker is the one on the right
side when you face the unit.
" Do not let the bare speaker wires touch
each other.
" Do not allow any objects to fall into or to be
placed in the bass reflex ducts.
" Do not stand or sit on the speakers. You may
Incorrect
be injured.
Notes:
" The speakers are magnetically shielded.
Therefore, they do not affect the display even if you use them near
the TV. However, some color variation may occur, depending on
the type of TV used.
Notes:
" Placing the antenna on the stereo system or near the AC power
cord may cause noise pickup. Place the antenna away from the
stereo system for better reception.
" Do not connect the attached FM antenna to an external antenna
as this may cause trouble.
Installing the AM loop antenna:
< Assembling >
If color variation occurs...
Turn off the TV (from the power switch).
After 15 - 30 minutes, turn the TV on again.
Preparation for Use
3
< Attaching to the wall >
Wall
4
5
6
7
8
9
Screws (not supplied)
If the color variation is still present...
Move the speakers further away from the TV.
10
" If any kind of magnet or an electromagnet is placed too close to the
TV and the system, irregular colors may appear on the TV screen.
11
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Preparation for Use
XL-MP60
System connections (continued)
! Connecting the AC power cord
! Demonstration mode
After checking all the connections have been made correctly, connect the AC power cord to the AC power input jack, then plug the AC
power cord of this unit into the AC outlet. If you plug in the unit first,
the unit will enter the demonstration mode.
When you plug the unit in for the first time,
the unit will enter the demonstration
mode. You will see words scroll.
To cancel the demonstration
mode:
When the unit is in the power standby mode (demonstration mode),
press the X-BASS/DEMO button.
The unit will enter the low power
consumption mode.
AC outlet
(AC 120 V, 60 Hz)
Notes:
" Never use a power cord other than the one supplied. Otherwise,
a malfunction or an accident may occur.
" Unplug the AC power cord from the AC outlet if the unit will not be
in use for a prolonged period of time.
To return to the demonstration mode:
When the unit is in the power stand-by mode, press the X-BASS/
DEMO button again.
Note:
When the power is on, the X-BASS/DEMO button can be used to select the extra bass mode.
Cooling fan:
This product is equipped with a cooling fan inside for better heat radiation.
12
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Remote control
! Battery installation
Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1
2
3
Remove the battery cover.
Insert the batteries according to the direction indicated in
the battery compartment.
When inserting or removing the batteries, push them toward the
battery terminals.
Replace the cover.
XL-MP60
1
Notes concerning use:
" Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.
" Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
" Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit if this
occurs.
" Keep the remote control away from moisture, heat, shock, and
vibrations.
2
3
Check the remote control after checking all the connections (see
pages 10 - 12).
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.
Remote sensor
Precautions for battery use:
" Replace all old batteries with new ones at the same time.
" Do not mix old and new batteries.
" Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.
Preparation for Use
! Test of the remote control
4
5
6
7
8
8" - 20'
(0.2 m - 6 m)
9
Caution:
" Do not use rechargeable batteries (nickel-cadmium battery, etc.).
" Installing the batteries incorrectly may cause the unit to malfunction.
Battery removal:
Remove the battery cover. Push each battery toward the battery
terminal and take them out.
10
13
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
General control
! Volume control
Main unit operation:
When the VOLUME control is turned clockwise, the volume will
increase. When it is turned counterclockwise, the volume will
decrease.
Remote control operation:
Press the VOLUME (+ or -) button to increase or decrease the volume.
0 ..... 30 MAXIMUM
Basic Operation
! Bass control (X-BASS)
When the power is first turned on, the unit will enter the extra bass
mode which emphasizes the bass frequencies, and "X-BASS" will
appear. To cancel the extra bass mode, press the X-BASS/DEMO
(X-BASS) button.
! Equalizer
! To turn the power on
Press the ON/STAND-BY button to turn the power on.
When the EQUALIZER (EQUALIZER MODE) button is pressed, the
current mode setting will be displayed. To change to a different
mode, press the EQUALIZER (EQUALIZER MODE) button repeatedly until the desired sound mode appears.
After use:
Press the ON/STAND-BY button to enter the power stand-by
mode.
FLAT
The sound is not modified.
ROCK
Bass and treble are emphasized.
CLASSIC Treble is cut a little.
POPS
Bass and treble are slightly emphasized.
VOCAL
Vocals (midrange tones) are emphasized.
JAZZ
Treble is slightly emphasized.
14
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Setting the clock
XL-MP60
1
3
Within 30 seconds, press the PRESET ( or ) button to
adjust the hour and then press the MEMORY/SET button.
2
Press the PRESET ( or ) button once to advance the time
by 1 hour. Hold it down to advance continuously.
Press the PRESET ( or ) button once to advance the time
by 1 minute. Hold it down to advance continuously.
In this example, the clock is set for the 12-hour (AM 12:00) display.
1
2
Press the CLOCK button and within 8 seconds, press the
MEMORY/SET button.
Within 30 seconds, press the PRESET ( or ) button to
select 12-hour or 24-hour display and then press the MEMORY/SET button.
3
Within 30 seconds, press the PRESET ( or ) button to
adjust the minutes and then press the MEMORY/SET button.
To confirm the time display:
Press the CLOCK button.
The time display will appear for
about 8 seconds.
Note:
The "CLOCK" or time will flash at the push of the CLOCK button
when the AC power supply is restored after a power failure or
unplugging the unit.
Readjust the clock as follows.
4
Basic Operation
4
"0:00"
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
10
15
XL-MP60(U).fm
7
9
To change the 12-hour or 24-hour display:
1 Clear all the programmed contents. [Refer to "Clearing all the
memory (reset)" on page 30 for details.]
2 Perform "Setting the clock" from step 1.
05/1/28
6
8
To readjust the clock:
Perform "Setting the clock" from step 1. If the "CLOCK" is not flashing in step 1, step 2 (for selecting the 12-hour or 24-hour display) will
be skipped.
"AM 12:00"
5
TINSEA043SJZZ
XL-MP60
Listening to a disc
This system can play back a standard CD, CD-R/RW in the CD format and CD-R/RW with MP3 or WMA files, but cannot record on
them.
Some audio CD-R and CD-RW discs may not be playable due to the
state of the disc or the equipment used for recording.
Disc Playback
CD:
The CD indicator will light up when a normal CD is loaded.
MP3:
MP3 is a form of compression. It is an acronym which stands for
MPEG Audio Layer 3.
MP3 is a type of audio code which is processed by significant compression from the original audio source with very little loss in sound
quality.
" The MP3 track indicator will light up when an MP3 track is read.
" This system supports MPEG 1 Layer 3, MPEG 2 Layer 3, and
VBR files.
" During VBR file playback, time counter in the display may differ
from its actual playback time.
WMA:
WMA files are ASF (Advanced Systems Format) audio files which
are compressed with Windows Media Audio codec. WMA is developed by Microsoft as an audio format file for Windows Media Player.
" The WMA track indicator will light up when a WMA track is read.
" Supported bit rates for WMA files range from 64 kbps to 160 kbps.
16
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
1
1
2
3
Press the ON/STAND-BY button to turn the power on.
6
Press the CD button.
Press the OPEN/CLOSE button to close the disc compartment.
[CD]
CD indicator
2
1
3
Press the OPEN/CLOSE button
to open the disc compartment.
All trays open in tiers.
4
MP3 track indicator
[MP3]
Place the disc on the disc tray 1, label side up.
2
4
5" (12 cm)
3" (8 cm)
1
WMA track indicator
[WMA]
5
To place discs in the trays 2 - 5
1
1 Total number of tracks on the disc whose number is flashing.
2 Total playing time of the CD whose number is flashing.
1. Slide in the tray with a disc toward the unit.
7
Press the
/
button to start playback.
Disc Playback
Be sure to place 3" (8 cm) discs in the middle of the disc trays.
5
6
7
Disc play indicator
2. Place a disc in an empty tray.
8
" Playback will begin from track 1 on disc 1. After that disc finishes
playing, the next disc will automatically play.
" After the last track on the fifth disc is played, the CD player stops
automatically.
" When there is no disc in one of the disc trays (1 - 5), the empty
tray will be skipped to the next tray with a disc.
" Due to the structure of the disc information, it takes longer
(approximately 20 to 90 seconds) to read a CD-R/RW disc
recorded in the MP3 or WMA format than a normal CD.
9
10
17
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
Listening to a disc (continued)
To remove the discs:
1. In the stop mode, press the
OPEN/CLOSE button.
" All trays open in tiers.
2. Remove the disc in the tray 1.
Disc Playback
3. Slide in the tray 1 toward the unit.
In the same way, remove discs in
the trays 2 - 5.
4. After removing the discs, press
the OPEN/CLOSE button again.
18
To specify a tray to open:
1. In the stop mode, press the 1 - 5 button.
2. Press the OPEN/CLOSE button.
3. Remove the disc, then press the OPEN/CLOSE button again.
Caution:
" Do not place two discs in one disc tray.
" Do not play discs with special shapes (heart or octagon shaped)
as it may cause malfunctions.
" Do not push the disc compartment while it is moving.
" If the power fails while the disc compartment is open, wait until
the power is restored.
" If the disc compartment is stopped with force, the unit will not
function. If this occurs, press the ON/STAND-BY button to enter
the power stand-by mode and then turn the power on again.
" If TV or radio interference occurs during disc operation, move the
unit away from it.
" If a disc is damaged, dirty, or loaded upside down, the disc will
skip or not play.
! Various disc functions
Function
Main unit
Remote
control
Operation
Play
Press in the stop mode.
Stop
Press in the playback
mode.
Pause
Press in the playback
mode. Press the / button to resume playback
from the paused point.
Track up/
Track down
Press in the playback or
stop mode.
If you press the button in the
stop mode, press the /
button to start the desired
track.
Fast forward/Fast
reverse
Press and hold down in the
playback mode.
Release the button to resume playback.
Notes:
" Track up/track down and fast forward/fast reverse are possible only
within one disc.
" When the end of the last track is reached during fast forward, "
END" will appear on the display and disc operation will be paused.
When the beginning of the first track is reached during fast reverse,
the unit will enter the playback mode.
( : Last track number)
" CD sound is heard during fast forward/fast reverse, except for CD-R/
RW in the MP3 or WMA format. (Check elapsed time on the display.)
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Advanced disc playback
XL-MP60
1
! To change the display (CD-R/RW discs
recorded in the MP3 or WMA format only)
While in the stop mode or playback mode, press the DISPLAY button.
Each time the button is pressed, the display will change as follows.
2
[When in the stop mode]
3
! To select the desired folder or track by name
(CD-R/RW discs recorded in the MP3 or WMA
format only)
1
While in the stop mode, press the
DISPLAY button on the remote
control to display the folder
name.
2
3
Select the desired folder by pressing the
4
5
Select the desired track by pressing the
or
Folder name
4
Track name
[When in the playback mode]
Elapsed
Track
number playback
time
Folder name
Album name
Artist name
Track name
Disc Playback
Total number of tracks
button.
Press the DISPLAY button to display the track name.
Press the
playback.
/
or
5
6
7
8
Title name
button.
button to begin
9
10
19
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
Advanced disc playback (continued)
! To play from a specified disc
! Direct track search
You can start playback from the desired disc by selecting the number.
By using the direct search buttons, the desired tracks on the current
disc can be played.
1
Press one of the
1-
5 buttons to select the desired disc.
Use the direct search buttons on
the remote control to select the desired track while playing the selected disc.
Selected track number
Disc Playback
Selected disc number
2
Press the
/
button.
A. For example, to choose 13
1 Press the "+10" button once.
2 Press the "3" button.
" Playback will begin from track 1 on the chosen disc. After that
disc finished playing the next disc automatically play.
" After the last track on the fifth disc is played, the CD player stops
automatically.
Note:
If a disc tray with no disc is selected, playback will not start and the
disc indicator will go out.
To stop playback:
Press the
button.
20
" The direct search buttons allow you to select up to number 9.
" When selecting number 10 or higher, use the +10 button.
B. For example, to choose 30
1 Press the "+10" button three times.
2 Press the "0" button.
If the direct search buttons are pressed while the disc is stopped,
press the / button to start the desired track on the current disc.
Notes:
" A track number higher than the number of tracks on the disc cannot be selected.
" During random play, direct search is not possible.
" For CD-R/RW discs recorded in the MP3 or WMA format, you can
select the track number but cannot select the folder by pressing
the direct search buttons.
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
1
! Repeat play
! Random play
You can play up to 5 discs, or programmed tracks continuously.
The tracks on the disc(s) can be played in random order automatically.
To repeat all tracks on up to 5 discs:
Press the
/
2
To random play all tracks on up to 5 discs:
button twice.
Press the RANDOM button on the remote control.
3
To repeat desired tracks:
To repeat random play:
Press the / button during random play.
To cancel random play:
Press the button.
"R" will go out.
To cancel repeat play:
Press the / button again.
" " will go out.
Caution:
After performing repeat play, be sure to press the
wise, the disc(s) will play continuously.
button. Other-
Notes:
" Random play will stop automatically when all tracks are played
once. (The same track will not be played back twice.)
" If you press the
button during random play, you can move to
the next track by the random operation. On the other hand, the
button does not allow you to move to the previous track. The
beginning of the track being played will be located.
" In random play, the CD player will select and play tracks automatically. (You cannot select the order of the tracks.)
Disc Playback
4
Perform steps 1 - 4 in the "Programmed play" section on page 22
and then press the / button twice.
5
6
7
8
9
10
21
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
Advanced disc playback (continued)
! Programmed play
You can choose up to 32 selections for playback in the order you
like.
1
While in the stop mode, press one of the
select the desired disc.
1-
5 buttons to
Disc Playback
Selected disc number
2
Press the direct search buttons on the remote control to
select the desired track.
You can also select a track by pressing the
or
button.
Selected track number
3
Press the MEMORY/SET button to save the track number.
4
Repeat steps 1 - 3 for other tracks. Up to 32 tracks can be
programmed.
5
Press the
/
To clear the programmed selections:
While the "MEMORY" indicator is lit, set the
CD to the stop mode and then press the
CLEAR button.
Each time the button is pressed, one track will
be cleared, beginning with the last track programmed.
Adding tracks to the program:
If a program has been previously stored, the "MEMORY" indicator
will be displayed. Then follow steps 1 - 3 to add tracks. The new
tracks will be stored after the last track of the original program.
Notes:
" Opening the disc compartment automatically cancels the programmed sequence.
" If you press the ON/STAND-BY button to enter the stand-by
mode or change the function from CD to another, the programmed selections will not be cleared.
" During the program operation, random play is not possible.
" For CD-R/RW discs recorded in the MP3 or WMA format, you can
select the track number but cannot select the folder by pressing
the direct search buttons.
button to start playback.
22
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Listening to the radio
XL-MP60
1
! Tuning
1
2
Press the ON/STAND-BY button to turn the power on.
3
Press the TUNING (
station.
2
Press the TUNER (BAND) button repeatedly to select the
desired frequency band (FM or AM).
or
) button to tune in to the desired
3
4
Auto tuning:
When the TUNING button is pressed for more than 0.5 seconds, scanning will start automatically and the tuner will stop at
the first receivable broadcast station.
5
Notes:
" When radio interference occurs, auto scan tuning may stop automatically at that point.
" Auto scan tuning will skip weak signal stations.
" To stop the auto tuning, press the TUNING button again.
Radio
Manual tuning:
Press the TUNING button as many times as required to tune in
to the desired station.
6
7
To receive an FM stereo transmission:
Press the TUNER (BAND) button to display the "ST" indicator.
" " " will appear when an FM broadcast is in stereo.
" If the FM reception is weak, press the TUNER (BAND) button to
extinguish the "ST" indicator. The reception changes to monaural, and the sound becomes clearer.
8
9
FM stereo mode indicator
10
FM stereo receiving indicator
23
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Radio
XL-MP60
Listening to the radio (continued)
! Memorizing a station
! To recall a memorized station
You can store 40 AM and FM stations in memory and recall them at
the push of a button. (Preset tuning)
Press the PRESET ( or
lect the desired station.
1
2
Perform steps 1 - 3 in "Tuning" on page 23.
3
Within 30 seconds, press the PRESET ( or ) button to
select the preset channel number.
Store the stations in memory, in order, starting with preset
channel 1.
4
Within 30 seconds, press the MEMORY/SET button to store
that station in memory.
Press the MEMORY/SET button to enter the preset tuning
saving mode.
) button for less than 0.5 seconds to se-
! To scan the preset stations
The stations saved in memory can be scanned automatically. (Preset memory scan)
1 Press the PRESET ( or ) button for more than 0.5 seconds.
The preset number will flash and the programmed stations will be
tuned in sequentially, for 5 seconds each.
2 Press the PRESET ( or ) button again when the desired station is located.
If the "MEMORY" and preset number indicators go out before
the station is memorized, repeat the operation from step 2.
5
Repeat steps 1 - 4 to set other stations, or to change a preset station.
When a new station is stored in memory, the station previously
memorized will be erased.
! To erase entire preset memory
1
2
Press the ON/STAND-BY button to enter the stand-by mode.
While pressing down the TUNER(BAND) button and the 2 button, press the ON/STAND-BY button until "TUNER CL" appears.
Note:
The backup function protects the memorized stations for a few hours
should there be a power failure or the AC power cord get disconnected.
24
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Timer and sleep operation
Sleep operation:
The radio and compact disc can all be turned off automatically.
1
! Timer playback
Before setting timer:
1 Press the CLOCK button to check that the clock is set to the correct time. (Refer to page 15.)
2 Load the discs to be played.
2
3
1
2
Press the ON/STAND-BY button to turn the power on.
3
Adjust the volume using the VOLUME buttons.
Press the CD or TUNER (BAND) button to select the desired function.
When you select the TUNER (BAND), tune into the desired station.
Do not turn the volume up too high.
4
5
Press the TIMER/SLEEP button repeatedly until " " is displayed and then within 8 seconds, press the MEMORY/SET
button.
Advanced Features
Timer playback:
The unit turns on and plays the desired source (CD, tuner) at the
preset time.
XL-MP60
Within 30 seconds, press the PRESET ( or ) button to
specify the hour to start, then press the MEMORY/SET button.
4
5
6
7
8
9
10
Continued to the next page
25
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
Timer and sleep operation (continued)
6
Within 30 seconds, press the PRESET ( or ) button to
specify the minute to start, then press the MEMORY/SET
button.
Advanced Features
" Settings are displayed in order and the unit will enter the timer stand-by mode.
" Timer set indicator will light up.
To reset or change the timer setting:
Perform "Timer playback" from the beginning.
Note:
When performing timer playback using another unit connected to
the VIDEO/AUX IN jacks, select "VIDEO/AUX" in step 2.
At this time, only this unit will be turned on or enter the power standby mode automatically. It will enter the power stand-by mode 1 hour
after the playback starts. However, the other unit will not be turned
on or off.
To cancel the timer playback:
Press the ON/STAND-BY button to turn the power on.
7
When the preset time is reached, playback will start.
The volume will increase gradually until it reaches the volume
you were listening to before your system entered the timer
stand-by mode.
8
The unit will enter the power stand-by mode one hour after
the timer playback starts.
26
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
1
2
Play back the desired sound source.
Press the TIMER/SLEEP button repeatedly until "SLEEP" is
displayed and then within 8 seconds, press the MEMORY/
SET button.
3:00
3
4
2:00
0:05
1:30
0:10
Example: To fall asleep and wake up to the same radio station
You can play back the same source only (the function cannot be
switched).
1
2
or
3
While the sleep timer is set, set the timer playback (steps 4
- 6, pages 25 - 26).
Timer playback setting
)
5 minute - 3 hours
Sleep operation will
automatically stop.
1:00
0:15
2
Set the sleep time (see left, steps 1 - 3).
Sleep timer setting
To change the sleep time:
While the sleep time is displayed, press the PRESET (
button.
(Maximum: 3 hours - Minimum: 5 minutes)
(cancel)
1
! To use timer and sleep operation together
0:30
Within 30 seconds, press the MEMORY/SET button.
The unit will enter the power stand-by mode automatically
after the preset time has elapsed.
The volume will be turned down 30 seconds before the sleep
operation finishes.
Timer playback
start time
Advanced Features
! Sleep operation
4
5
6
7
To confirm the remaining sleep time:
Press the TIMER/SLEEP button while the sleep timer is set.
The remaining sleep time is displayed for about 8 seconds.
8
To cancel the sleep operation:
Press the ON/STAND-BY button while the sleep timer is set.
9
10
27
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
Enhancing your system
The connection cord is not included. Purchase a commercially available cord as shown below.
VCR, DVD, etc.
White
To the line
output jacks
White
Red
Advanced Features
Red
RCA cord
(not supplied)
! Listening to the playback sounds from VCR,
DVD, etc.
1
Use a connection cord to connect the VCR, DVD, etc. to the
VIDEO/AUX IN jacks.
When using video equipment, connect the audio output to this
unit and the video output to a television.
2
Press the ON/STAND-BY button to turn the power on.
3
Press the VIDEO/AUX button.
4
Play the connected equipment.
Note:
To prevent noise interference, place the unit away from the television.
! Headphones
" Before plugging in or unplugging the headphones, reduce the volume.
" Be sure your headphones have a 1/8" (3.5 mm) diameter plug
and impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
" Plugging in the headphones disconnects the speakers automatically. Adjust the volume using the VOLUME control.
28
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Troubleshooting chart
! General
Symptom
Possible cause
" The clock is not set to the " Did a power failure occur? Reset
correct time.
the clock. (Refer to page 15.)
" When a button is pressed, " Set the unit to the power standthe unit does not respond.
by mode and then turn it back on.
" If the unit still malfunctions, reset
it. (Refer to page 30.)
" No sound is heard.
" Is the volume level set to "0"?
" Are the headphones connected?
" Are the speaker wires disconnected?
Symptom
" The remote control does
not operate.
Symptom
Possible cause
Possible cause
" Is the AC power cord of the unit
plugged in?
" Is the battery polarity correct?
" Are the batteries dead?
" Is the distance or angle incorrect?
" Does the remote control sensor
receive strong light?
2
3
4
! Tuner
Symptom
Possible cause
" The radio makes unusual
noises continuously.
" Is the unit placed near the TV or
computer?
" Is the FM antenna or AM loop antenna placed properly? Move the
antenna away from the AC power
cord if it's located nearby.
! CD player
" Playback does not start.
" Is the disc loaded upside down?
" Playback stops in the mid- " Does the disc satisfy the standle or is not performed
dards?
properly.
" Is the disc distorted or
scratched?
" Playback sounds are
" Is the unit located near excessive
skipped, or stopped in the
vibrations?
middle of a track.
" Is the disc very dirty?
1
! Remote control
References
Many potential problems can be resolved by the owner without calling a service technician.
If something is wrong with this product, check the following before
calling your authorized SHARP dealer or service center.
XL-MP60
! Condensation
5
6
7
Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet (CD
pickup, etc.) or on the transmitter on the remote control.
Condensation can cause the unit to malfunction. If this happens,
leave the power on with no disc in the unit until normal playback is
possible (about 1 hour). Wipe off any condensation on the transmitter with a soft cloth before operating the unit.
8
9
" Has condensation formed inside
the unit?
10
29
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
XL-MP60
Troubleshooting chart (continued)
! If trouble occurs
! Care of compact discs
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in the previous operation, unplug and
plug in the unit, and then turn the power on.
Discs are fairly resistant to damage, however mistracking can occur
due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your disc collection and
player.
" Do not write on either side of the disc, particularly the non-label
side from which signals are read. Do not mark this surface.
" Keep your discs away from direct sunlight, heat, and excessive
moisture.
" Always hold the discs by the edges. Fingerprints, dirt, or water on
the discs can cause noise or mistracking. If a disc is dirty or does
not play properly, clean it with a soft, dry cloth, wiping straight out
from the center, along the radius.
Note:
If neither operation above restores the unit, clear all the memory by
resetting it.
References
! Clearing all the memory (reset)
1
2
NO
Press the ON/STAND-BY button to enter the power stand-by
mode.
While pressing down the CD button and the 2 button, press the
ON/STAND-BY button until "CLEAR" appears.
YES
Correct
Maintenance
Caution:
This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD program.
! Before transporting the unit
Remove all discs from the unit. Make sure there is no disc in the disc
tray. Then, set the unit to the power stand-by mode. Carrying the
unit with discs left inside can damage the unit.
! Cleaning the CD pickup lens
In order to ensure proper operation of the CD player, preventative
maintenance (cleaning of the laser pickup lens) should be performed periodically. Lens cleaners are commercially available. Contact your local CD software dealer for options.
! Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.
30
Caution:
" Do not use chemicals for cleaning (gasoline, paint thinner, etc.). It
may damage the cabinet finish.
" Do not apply oil to the inside of the unit. It may cause malfunctions.
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
Specifications
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be
some deviations from these values in individual units.
! Amplifier
Output terminals
Input terminals
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1,720 kHz
2
Front speakers: 37.5 watts minimum RMS
per channel into 6 ohms from 100 Hz to
20 kHz, 10% total harmonic distortion
Subwoofer: 45 watts minimum RMS into
6 ohms from 70 Hz to 130 Hz, 10% total
harmonic distortion
Front speakers and subwoofer: 6 ohms
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
Video/Auxiliary (audio signal):
500 mV/47 k ohms
! CD player
Type
5-disc multi-play compact disc player
Signal readout
Non-contact, 3-beam semiconductor laser
pickup
Type
Maximum input
power
Rated input power
Impedance
Dimensions
2-way type speaker system
(magnetic shield)
1.5" (4 cm) tweeter
4" (10 cm) woofer
75 W
37.5 W
6 ohms
Width: 6-1/2" (165 mm)
Height: 9-7/16" (240 mm)
Depth: 8-3/16" (208 mm)
4.9 lbs. (2.2 kg)/each
Weight
! Subwoofer
Type
Maximum input
power
Rated input power
Impedance
Dimensions
Weight
3
4
References
AC 120 V, 60 Hz
Power consumption 121 W
Dimensions
Width: 6-5/16" (160 mm)
Height: 9-7/16" (240mm)
Depth: 12-9/16" (319mm)
Weight
11.5 lbs. (5.2 kg)
Output power
1
! Tuner
! Front speaker
! General
Power source
XL-MP60
5
6
5-1/8" (13 cm) subwoofer system
(magnetic shield)
90 W
7
45 W
6 ohms
Width: 6-5/16" (160 mm)
Height: 9-7/16" (240 mm)
Depth: 11-1/4" (285mm)
8
9
7.3 lbs. (3.3 kg)
D/A converter
1-bit D/A converter
Frequency response 20 - 20,000 Hz
Dynamic range
90 dB (1 kHz)
10
31
05/1/28
XL-MP60(U).fm
TINSEA043SJZZ
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof
with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has
been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in
design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any
warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser.
Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the
purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event
shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states
do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
SHARP ELECTRONICS CORPORATION
XL-MP60
Micro
Component
System
Sharp Plaza,
Mahwah,
New
Jersey 07430-2135
(Be sure to have this information available when you need service for your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
9906
SHARP CORPORATION
Additional Item(s) Excluded from Warranty Coverage (if any): Non-functional accessories, supplies, and consumable items.
Where to Obtain Service:
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1-800-BE-SHARP.
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized Servicer.
Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and
packaged securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.
0005
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
05/2/9
9906
XL-MP60(U)_BACK.fm
Printed in China
TINSEA043SJZZ
05B N HK 2
TINSEA043SJZZ
Download PDF