Woodstock SHOP FOX W1828 Specifications

Woodstock SHOP FOX W1828 Specifications
MODEL W1828
12" DISC SANDER
OWNER'S MANUAL
(FOR MODELS MANUFACTURED SINCE 4/11)
Phone: (360) 734-3482 • Online Technical Support: [email protected]
COPYRIGHT © MAY, 2011 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#14118TS Printed in China
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property
damage from negligence, improper training, machine modifications or
misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
ELECTRICAL..........................................9
SERVICE............................................. 23
General........................................... 23
Table/Disc Parallelism.......................... 23
Miter Gauge Calibration........................ 24
Table Tilt Calibration........................... 24
Troubleshooting.................................. 25
Electrical Safety Instructions.................. 27
Wiring Diagram.................................. 28
PARTS................................................ 29
WARRANTY......................................... 33
OPERATIONS
OPERATIONS........................................ 16
General........................................... 16
Basic Controls.................................... 16
Disabling ON/OFF Switch...................... 17
Operation Overview............................ 17
Choosing Sandpaper............................ 18
Stock Inspection and Requirements.......... 18
Attaching Sandpaper............................ 19
Disc Sanding...................................... 20
SETUP
SETUP............................................... 11
Needed for Setup............................... 11
Unpacking........................................ 11
Inventory......................................... 11
Machine Placement............................. 12
Cleaning Machine................................ 12
Bench Mounting................................. 13
Dust Collection.................................. 13
Power Connection............................... 14
Test Run........................................... 15
MAINTENANCE..................................... 22
General........................................... 22
Cleaning.......................................... 22
Table & Base..................................... 22
Lubrication....................................... 22
ELECTRICAL
SAFETY................................................6
Standard Machinery Safety Instructions....... 6
Additional Safety for Disc Sanders............. 8
ACCESSORIES....................................... 21
SAFETY
INTRODUCTION......................................2
Woodstock Technical Support................... 2
Machine Specifications........................... 3
Controls and Features............................ 5
INTRODUCTION
Contents
MAINTENANCE
SERVICE
PARTS
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
INTRODUCTION
Model W1828 (For Machines Mfg. Since 4/11)
INTRODUCTION
Woodstock Technical Support
This machine has been specially designed to provide many years of trouble-free service. Close attention
to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please contact
Woodstock International Technical Support at (360) 734-3482 or send e-mail to: [email protected]
biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [email protected]
-2-
INTRODUCTION
Model W1828 (For Machines Mfg. Since 4/11)
MODEL W1828
SHOP FOX 12" DISC SANDER
Motors
Main
Type..................................................................................... TEFC Capacitor Start
Horsepower................................................................................................. 1 HP
Voltage...................................................................................................... 110V
Phase...................................................................................................... Single
Amps.......................................................................................................... 10A
Speed.................................................................................................. 1725 RPM
Cycle....................................................................................................... 60 Hz
Number of Speeds............................................................................................. 1
Power Transfer ................................................................................... Direct Drive
Bearings............................................................... Sealed and Permanently Lubricated
Main Specifications
Table Info
Table Width........................................................................................... 4-1/2 in.
Table Length......................................................................................... 15-3/4 in.
Table Thickness......................................................................................... 3/4 in.
Table Tilt............................................................................................ 0 – 45 deg.
Miter Gauge Slot Width................................................................................ 5/8 in.
Miter Gauge Slot Height............................................................................... 1/4 in.
Spindle Info
Arbor Size................................................................................................ 15 mm
Total Arbor Length................................................................................... 1-1/2 in.
Disc Info
Sanding Disc Diameter................................................................................... 12 in.
Sanding Disc Speed.................................................................................. 1725 RPM
Construction
Base.................................................................................................... Cast Iron
Table................................................................................................... Cast Iron
Frame.................................................................................................. Cast Iron
Disc.............................................................................................. Cast Aluminum
Miter Gauge.................................................................................... Cast Aluminum
Paint....................................................................................................... Epoxy
Other
No. Of Dust Ports.............................................................................................. 1
Dust Port Size.............................................................................................. 2 in.
Model W1828 Machine Specifications, Page 1 of 2
-3-
INTRODUCTION
Model W1828 (For Machines Mfg. Since 4/11)
Product Dimensions
Weight........................................................................................................... 68 lbs.
Width (side-to-side) x Depth (front-to-back) x Height.............................. 18 x 17-3/8 x 14-1/2 in.
Footprint (Length x Width).............................................................................. 13 x 10 in.
Shipping Dimensions
Type......................................................................................................... Cardboard
Content........................................................................................................ Machine
Weight........................................................................................................... 74 lbs.
Length x Width x Height........................................................................... 18 x 18 x 17 in.
Electrical
Power Requirement.................................................................... 110V, Single-Phase, 60 Hz
Full-Load Current Rating........................................................................................ 7.5A
Minimum Circuit Size............................................................................................. 15A
Switch.............................................................................. Paddle Switch w/Disabling Key
Switch Voltage.................................................................................................... 110V
Cord Length....................................................................................................... 5 ft.
Cord Gauge.................................................................................................. 16 Gauge
Plug Included....................................................................................................... Yes
Included Plug Type........................................................................................ NEMA 5-15
Other
Country Of Origin ............................................................................................... China
Warranty ........................................................................................................ 2 Year
Assembly Time ............................................................................................. 5 Minutes
Features
Locking Miter Bar
Built-In Dust Port
Non-Slip Rubber Feet
Model W1828 Machine Specifications, Page 2 of 2
-4-
INTRODUCTION
Model W1828 (For Machines Mfg. Since 4/11)
Controls and Features
Sanding Disc
Motor
ON/OFF Switch
w/Disabling Key
Work Table
Miter Gauge
Dust Port
Table Tilt
Lock Handle
(1 of 2)
Work Table
Figure 1. Model W1828 controls and features.
READ and understand
this entire manual before
using this machine.
Serious personal injury
may occur if safety and
operational information
is not understood and
followed.
DO
NOT
risk your safety by not
reading!
-5-
Rubber
Foot
Model W1828 (For Machines Mfg. Since 4/11)
SAFETY
SAFETY
For Your Own Safety,
Read Manual Before Operating Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words intended to convey the level of importance of the
safety messages. The progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident prevention measures—this responsibility is ultimately up to the operator!
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
NOTICE
This symbol is used to alert the user to useful information about
proper operation of the equipment, and/or a situation that may
cause damage to the machinery.
Standard Machinery Safety Instructions
OWNER’S MANUAL. Read and understand this
owner’s manual BEFORE using machine.
Untrained users can be seriously hurt.
HEARING PROTECTION. Always wear hearing
protection when operating or observing
loud machinery. Extended exposure to this
noise without hearing protection can cause
permanent hearing loss.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating
or observing machinery to reduce the risk of
eye injury or blindness from flying particles.
Everyday eyeglasses are not approved safety
glasses.
MENTAL ALERTNESS. Be mentally alert when
running machinery. Never operate under the
influence of drugs or alcohol, when tired, or
when distracted.
HAZARDOUS DUST. Dust created while using
machinery may cause cancer, birth defects,
or long-term respiratory damage. Be aware
of dust hazards associated with workpiece
materials, and always wear a NIOSH-approved
respirator to reduce your risk.
DISCONNECTING POWER SUPPLY. Always
disconnect machine from power supply before
servicing, adjusting, or changing cutting tools
(bits, blades, cutters, etc.). Make sure switch
is in OFF position before reconnecting to avoid
an unexpected or unintentional start.
WEARING PROPER APPAREL. Do not wear
clothing, apparel, or jewelry that can become
entangled in moving parts. Always tie back
or cover long hair. Wear non-slip footwear to
avoid accidental slips which could cause a loss
of workpiece control.
DANGEROUS ENVIRONMENTS. Do not use
machinery in wet or rainy locations, cluttered
areas, around flammables, or in poorly-lit
areas. Keep work area clean, dry, and welllighted to minimize risk of injury.
-6-
Model W1828 (For Machines Mfg. Since 4/11)
STABLE MACHINE. Unexpected movement during
operations greatly increases the risk of injury
and loss of control. Verify machines are
stable/secure and mobile bases (if used) are
locked before starting.
FORCING MACHINERY. Do not force machine. It
will do the job safer and better at the rate for
which it was designed.
ONLY USE AS INTENDED. Only use machine for
its intended purpose. Never modify or alter
machine for a purpose not intended by the
manufacturer or serious injury may result!
AWKWARD POSITIONS. Keep proper footing and
balance at all times when operating machine.
Do not overreach! Avoid awkward hand
positions that make workpiece control difficult
or increase the risk of accidental injury.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for
recommended accessories. Using improper
accessories will increase the risk of serious
injury.
UNATTENDED OPERATION. Never leave machine
running while unattended. Turn machine off
and ensure all moving parts completely stop
before walking away.
CHILDREN & BYSTANDERS. Keep children and
bystanders a safe distance away from work
area. Stop using machine if children or
bystanders become a distraction.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to
keep machine in good working condition. An
improperly maintained machine may increase
the risk of serious injury.
REMOVE ADJUSTING TOOLS. Never leave
adjustment tools, chuck keys, wrenches, etc.
in or on machine—especially near moving
parts. Verify removal before starting!
CHECK DAMAGED PARTS. Regularly inspect
machine for damaged parts, loose bolts,
mis-adjusted or mis-aligned parts, binding,
or any other conditions that may affect safe
operation. Always repair or replace damaged
parts, wires, cords, or plugs before operating
machine.
SECURING WORKPIECE. When required, use
clamps or vises to secure workpiece. A secured
workpiece protects hands and frees both of
them to operate the machine.
FEED DIRECTION. Unless otherwise noted, feed
work against the rotation of blades or cutters.
Feeding in the same direction of rotation may
pull your hand into the cut.
MAINTAIN POWER CORDS. When disconnecting
cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the
cord may damage the wires inside. Do not
handle the cord/plug with wet hands. Avoid
cord damage by keeping it away from heated
surfaces, high traffic areas, harsh chemicals,
and wet or damp locations.
GUARDS & COVERS. Guards and covers can
protect you from accidental contact with
moving parts or flying debris. Make sure
they are properly installed, undamaged, and
working correctly before using machine.
EXPERIENCING DIFFICULTIES. If at any time you
are experiencing difficulties performing the
intended operation, stop using the machine!
Contact our Technical Support for help at
(360) 734-3482.
NEVER STAND ON MACHINE. Serious injury or
accidental contact with cutting tool may
occur if machine is tipped. Machine may be
damaged.
-7-
SAFETY
APPROVED OPERATION. Untrained operators
can be seriously hurt by machinery. Only
allow trained or properly supervised people
to use machine. When machine is not being
used, disconnect power, remove switch keys,
or lock-out machine to prevent unauthorized
use—especially around children. Make
workshop kid proof!
Model W1828 (For Machines Mfg. Since 4/11)
SAFETY
Additional Safety for Disc Sanders
DISC DIRECTION. Only sand on the downwardmoving left side of the sanding disc. Sanding
on the upward-moving right side of the
sanding disc forces the operator to rely only
on hands (rather than the table) for support,
which increases the risk of workpiece "kickout" and impact/abrasion injuries.
WORKPIECE INSPECTION. Nails, staples, knots,
or other imperfections in the workpiece can
be dislodged and thrown from the sander
at a high rate of speed into the operator or
bystanders, or cause damage to sandpaper or
sander. Never attempt to sand stock that has
embedded foreign objects or questionable
imperfections.
AVOIDING ENTANGLEMENT. Becoming entangled
in the moving parts of this machine can cause
pinching and crushing injuries. To avoid these
hazards, DO NOT wear loose clothing, gloves,
or jewelry, and tie back long hair. Keep all
guards in place and secure.
FEEDING WORKPIECE. Forcefully jamming the
workpiece into the sanding surface could
cause the workpiece to be aggressively
grabbed and pull your hands into the sanding
surface. Always firmly grasp the workpiece
in both hands and ease it into the sandpaper
slowly using light pressure.
HAND PLACEMENT. Rotating sandpaper can
remove a large amount of flesh in a few
seconds. Always keep hands away from
the sandpaper during operation. Never
intentionally touch moving sandpaper.
SANDPAPER CONDITION. Sandpaper that is worn
or damaged not only produces poor sanding
results, but could fly apart, aggressively
grab the workpiece, and throw debris at the
operator. Always inspect the sandpaper before
operation and replace it if worn or damaged.
MINIMUM STOCK DIMENSION. Small workpieces
can be aggressively pulled from your hands
and present injury hazards. Always use a jig
or other holding device when sanding small
workpieces, and keep your hands and fingers
at least 2" away from the sanding surface.
IN-RUNNING NIP POINTS. The gap between
the moving sandpaper and the fixed table/
support creates a pinch point for fingers or
workpieces; the larger this gap is, the greater
the risk of fingers or workpieces getting
caught in it. Minimize this risk by adjusting
the table no more than 1⁄16" away from the
sandpaper.
WORKPIECE SUPPORT. Workpiece kickback can
occur with violent force if the workpiece
is not properly supported during operation.
Always sand with the workpiece firmly against
the table or another support device.
WORKPIECE INTEGRITY. Only sand solid
workpieces that can withstand the forces
required for power sanding. Make sure the
shape of the workpiece can be properly
supported on the table; avoid sanding
workpieces without flat bottom surfaces
unless some type of jig is used to maintain
support and control when the sanding force is
applied.
SANDING DUST. Sanding creates large amounts
of dust and flying chips that can lead to eye
injury or respiratory illness. Reduce the risk
of these hazards by always wearing approved
eye and respiratory protection when using the
sander.
Use this and other machinery with caution and respect. Always consider safety first, as it applies
to your individual working conditions. No list of safety guidelines can be complete—every shop
environment is different. Failure to follow guidelines could result in serious personal injury,
damage to equipment or poor work results.
-8-
Model W1828 (For Machines Mfg. Since 4/11)
ELECTRICAL
Availability
Full-Load Current Rating
The full-load current rating is the amperage a machine
draws at 100% of the rated output power. On machines
with multiple motors, this is the amperage drawn by the
largest motor or sum of all motors and electrical devices
that might operate at one time during normal operations.
Electrocution, fire, or equipment
damage may occur if machine is not
correctly grounded and connected to
the power supply.
Full-Load Current Rating at 110V................ 7.5 Amps
The full-load current is not the maximum amount of amps
that the machine will draw. If the machine is overloaded,
it will draw additional amps beyond the full-load rating.
If the machine is overloaded for a sufficient length of
time, damage, overheating, or fire may result—especially
if connected to an undersized circuit. To reduce the
risk of these hazards, avoid overloading the machine
during operation and make sure it is connected to a
power supply circuit that meets the requirements in the
following section.
Circuit Requirements
This machine is prewired to operate on a 110V power
supply circuit that has a verified ground and meets the
following requirements:
Nominal Voltage.................................... 110V/120V
Cycle.........................................................60 Hz
Phase............................................... Single-Phase
Minimum Circuit Size................................ 15 Amps
A power supply circuit includes all electrical equipment
between the breaker box or fuse panel in the building
and the machine. The power supply circuit used for
this machine must be sized to safely handle the fullload current drawn from the machine for an extended
period of time. (If this machine is connected to a circuit
protected by fuses, use a time delay fuse marked D.)
-9-
For your own safety and protection of
property, consult a qualified electrician
if you are unsure about wiring practices
or electrical codes in your area.
Note: The circuit requirements listed in this
manual apply to a dedicated circuit—where
only one machine will be running at a
time. If this machine will be connected to
a shared circuit where multiple machines
will be running at the same time, consult
a qualified electrician to ensure that the
circuit is properly sized for safe operation.
ELECTRICAL
Before installing the machine, consider the availability
and proximity of the required power supply circuit. If an
existing circuit does not meet the requirements for this
machine, a new circuit must be installed. To minimize
the risk of electrocution, fire, or equipment damage,
installation work and electrical wiring must be done by
a qualified electrician in accordance with all applicable
codes and standards.
Model W1828 (For Machines Mfg. Since 4/11)
Grounding & Plug Requirements
This machine MUST be grounded. In the event of certain
malfunctions or breakdowns, grounding reduces the risk of
electric shock by providing a path of least resistance for
electric current.
ELECTRICAL
This machine is equipped with a power cord that has an
equipment-grounding wire and a grounding plug (similar to
the figure on the right). The plug must only be inserted
into a matching receptacle (outlet) that is properly
installed and grounded in accordance with all local codes
and ordinances.
Improper connection of the equipment-grounding wire
can result in a risk of electric shock. The wire with
green insulation (with or without yellow stripes) is the
equipment-grounding wire. If repair or replacement of
the power cord or plug is necessary, do not connect the
equipment-grounding wire to a live (current carrying)
terminal.
Check with a qualified electrician or service personnel
if you do not understand these grounding requirements,
or if you are in doubt about whether the tool is
properly grounded. If you ever notice that a cord or
plug is damaged or worn, disconnect it from power, and
immediately replace it with a new one.
Serious injury could occur if you connect the machine to power before
completing the setup process. DO NOT
connect to power until instructed later
in this manual.
110V
GROUNDED
5-15 RECEPTACLE
Grounding Prong
5-15 PLUG
Neutral Hot
Figure 2. Typical 5-15 plug and receptacle.
Extension Cords
We do not recommend using an extension cord with this
machine. If you must use an extension cord, only use it if
absolutely necessary and only on a temporary basis.
Extension cords cause voltage drop, which may damage
electrical components and shorten motor life. Voltage
drop increases as the extension cord size gets longer
and the gauge size gets smaller (higher gauge numbers
indicate smaller sizes).
Any extension cord used with this machine must contain a
ground wire, match the required plug and receptacle, and
meet the following requirements:
Minimum Gauge Size.................................. 14 AWG
Maximum Length (Shorter is Better).................50 ft.
-10-
DO NOT modify the provided plug
or use an adapter if the plug will
not fit your receptacle. Instead, have
a qualified electrician install the
proper receptacle on a power supply
circuit that is grounded and meets the
requirements for this machine.
Model W1828 (For Machines Mfg. Since 4/11)
SETUP
Needed for Setup
The following are needed to complete the setup process,
but are not included with your machine.
Description
Qty
• Safety Glasses...............................................1
• Cleaner/Degreaser............................. As Needed
• Disposable Shop Rags.......................... As Needed
• Dust Collection System....................................1
• Dust Hose 2" ................................................1
• Dust Hose Clamp 2"........................................1
• Adapter 4" x 2" (Optional)................................1
• Dust Hose 4" (Optional)....................................1
• Dust Hose Clamp 4" (Optional)...........................1
• Mounting Hardware............................ As Needed
Keep machine disconnected from
power until instructed otherwise.
SETUP
Unpacking
This machine has been carefully packaged for safe
transportation. If you notice the machine has been
damaged during shipping, please contact your authorized
Shop Fox dealer immediately.
Inventory
The following is a description of the main components
shipped with the Model W1828. Lay the components out
to inventory them.
A
Note: If you can't find an item on this list, check the
mounting location on the machine or examine the
packaging materials carefully. Occasionally we pre-install
certain components for safer shipping.
Box Inventory (Figure 3)
Qty
A. Disc Sander Assembly......................................1
B. Sandpaper Disc 12" 80 Grit................................1
C. Miter Gauge Assembly.....................................1
B
C
Figure 3. Shipping inventory.
-11-
Model W1828 (For Machines Mfg. Since 4/11)
SETUP
Machine Placement
•
Workbench Load: This machine distributes
a heavy load in a small footprint. Some
workbenches may require additional bracing
to support both machine and workpiece.
•
Working Clearances: Consider existing and
anticipated needs, size of material to be
processed through the machine, and space
for auxiliary stands, work tables or other
machinery when establishing a location for
your sander (see Figure 4).
•
Lighting: Lighting should be bright enough
to eliminate shadow and prevent eye strain.
Cleaning Machine
The table and other unpainted parts of your
disc sander are coated with a waxy grease that
protects them from corrosion during shipment.
Clean this grease off with a solvent cleaner or
citrus-based degreaser. DO NOT use chlorinebased solvents such as brake parts cleaner or
acetone—if you happen to splash some onto a
painted surface, you will ruin the finish.
NEVER clean with gasoline
or other petroleumbased solvents. Most have
low flash points, which
make them extremely
flammable. A risk of
explosion and burning
exists if these products
are used. Serious personal
injury may occur if this
warning is ignored!
18"
Duct
3" Air
Gap
171/4"
Min.
ALWAYS work in wellventilated areas far from
possible ignition sources
when using solvents to
clean machinery. Many
solvents are toxic when
inhaled or ingested. Use
care when disposing
of waste rags and
towels to be sure they
DO NOT create fire or
environmental hazards.
Figure 4. Working clearances.
MAKE your shop “child
safe.” Ensure that your
workplace is inaccessible
to children by closing and
locking all entrances when
you are away. NEVER allow
untrained visitors in your
shop when assembling,
adjusting or operating
equipment.
-12-
Model W1828 (For Machines Mfg. Since 4/11)
Bench Mounting
We strongly recommend that you mount your sander to a
workbench to prevent it from moving during operation.
Before doing so, remove the included feet. An unexpected
movement could result in an injury or property damage.
When you have chosen the location to mount the sander,
the strongest option is a "Through Mount" where holes are
drilled all the way through the workbench, and hex bolts,
washers, and hex nuts are used to secure the machine
(see Figure 5).
Bolt
Flat Washer
Machine Base
Workbench
Flat Washer
Lock Washer
Hex Nut
Another option for mounting is a "Direct Mount" where the
machine is simply secured to the workbench with a lag
screw (see Figure 6).
Figure 5. Example of a through mount.
Flat Washer
Machine Base
Workbench
Dust Collection
Recommended CFM at Dust Port:...................98 CFM
Do not confuse this CFM recommendation with the rating
of the dust collector. To determine the CFM at the
dust port, you must take into account many variables,
including the CFM rating of the dust collector, the length
of hose between the dust collector and the machine, the
amount of branches or Y's, and the amount of other open
lines throughout the system. Explaining this calculation
is beyond the scope of this manual. If you are unsure of
your system, consult an expert or purchase a good dust
collection "how-to" book.
Figure 6. Example of a direct mount.
2"
Clamps
2" Port
2" Hose
4"x 2" Adapter
4" Hose
4" Clamp
To Dust Collector
DO NOT operate this machine without an adequate
dust collection system. This machine creates
substantial amounts of wood dust while operating.
Failure to use a dust collection system can result in
short and long-term respiratory illness.
-13-
Figure 7. Typical dust collection setup for
the Model W1828.
SETUP
Lag Screw
Model W1828 (For Machines Mfg. Since 4/11)
Power Connection
After you have completed all previous setup instructions
and circuit requirements, the machine is ready to be
connected to the power supply.
To avoid unexpected startups or property damage, use
the following steps whenever connecting or disconnecting
the machine.
Connecting Power
1. Turn the machine power switch OFF.
2. Insert the power cord plug into a matching power
supply receptacle. The machine is now connected to
the power source.
Figure 8. Connecting power.
Disconnecting Power
SETUP
1. Turn the machine power switch OFF.
2. Grasp the molded plug and pull it completely out of
the receptacle. Do not pull by the cord as this may
damage the wires inside.
Figure 9. Disconnecting power.
-14-
Model W1828 (For Machines Mfg. Since 4/11)
Test Run
Test run your machine to make sure it runs properly and
is ready for regular operation.
The test run consists of verifying the following: 1) The
motor powers up and runs correctly, and 2) the safety
disabling mechanism on the switch works correctly.
If, during the test run, you cannot easily locate the source
of an unusual noise or vibration, stop using the machine
immediately, then review Troubleshooting on Page 25.
If you still cannot remedy a problem, contact our Tech
Support at (360) 734-3482 for assistance.
Projectiles thrown from this machine
could cause serious eye injury. Wear
safety glasses to reduce the risk of
injury.
To test run the machine, do these steps:
1. Make sure you understand the safety instructions
at the beginning of the manual, and verify that the
machine is set up properly.
SETUP
2. Ensure all tools and objects used during setup are
cleared away from the machine.
3. Verify that the machine is operating correctly by
turning the machine ON.
—When operating correctly, the machine runs
smoothly with little or no vibration or rubbing
noises.
—Investigate and correct strange or unusual noises
or vibrations before operating the machine further.
Always disconnect the machine from power when
investigating or correcting potential problems.
4. Turn the machine OFF.
5. Remove the switch disabling key (Figure 10).
6. Try to start the machine with the paddle switch.
—If the machine does not start, the switch disabling
feature is working as designed.
—If the machine starts, immediately stop the
machine. The switch disabling feature is not
working correctly. Call Tech Support for help.
-15-
Figure 10. Removing switch key from
paddle switch.
Model W1828 (For Machines Mfg. Since 4/11)
OPERATIONS
General
This machine will perform many types of operations
that are beyond the scope of this manual. Many of these
operations can be dangerous or deadly if performed
incorrectly.
The instructions in this section are written with the
understanding that the operator has the necessary
knowledge and skills to operate this machine. If at any
time you are experiencing difficulties performing any
operation, stop using the machine!
If you are an inexperienced operator, we strongly
recommend that you read books or trade articles, or seek
training from an experienced operator before performing
any unfamiliar operations. Above all, your safety should
come first!
READ and understand this entire instruction manual before using this machine.
Serious personal injury may occur if
safety and operational information is not
understood and followed. DO NOT risk
your safety by not reading!
OPERATIONS
Basic Controls
Refer to Figure 11 and the following descriptions to
become familiar with the basic controls of this machine.
ON/OFF Switch
w/Switch Disabling Key
ON/OFF Switch. Turns the motor ON when flipped up;
turns motor OFF when pressed down.
Miter
Gauge
Switch Disabling Key. Disables the switch when the
yellow key is removed.
Table Tilt Lock Handles. Locks the table in place. To tilt
the table, loosen the handles, tilt the work table to the
desired angle, then re-tighten the handles.
Note: The work table should be set approximately
1
⁄16" away from the sanding disc to prevent fingers or
workpieces from getting caught. To adjust the work
table relative to the sanding disc, refer to in Table/Disc
Parallelism on Page 23.
Miter Gauge. Moves workpieces into the sanding disc
at a specific angle. To use the miter gauge, slide it into
the miter slot, loosen the lock knob, set the angle, then
re-tighten the knob.
-16-
Table Tilt Lock Handle
(1 of 2)
Figure 11. Basic controls.
Model W1828 (For Machines Mfg. Since 4/11)
Disabling ON/OFF Switch
The ON/OFF switch can be disabled by removing the
switch disabling key, as shown in Figure 12. Disabling the
switch in this manner can prevent unauthorized operation
of the machine, which is especially important if the
machine is not stored inside an access-restricted building.
IMPORTANT: Disabling the switch by removing the key
only restricts its function. It is not a substitute for
disconnecting power from the machine when adjusting or
servicing.
Children or untrained people can be
seriously injured by this machine. This
risk increases with unsupervised operation. To help prevent unsupervised
operation, disable the switch before
leaving the machine unattended! Place
the switch disabling key in a well-hidden or secure location.
Operation Overview
The purpose of this overview is to provide the novice
machine operator with a basic understanding of how
the machine is used during operation, so the machine
controls/components discussed later in this manual are
easier to understand.
To complete a sanding operation, the operator does
the following:
2. Adjusts the table tilt if necessary and locks the table
in place.
3. If necessary, inserts the miter gauge in the miter
slot, adjusts the miter gauge to the required sanding
angle, and locks it in place.
4. Wears safety glasses and a respirator.
5. Starts the machine and dust collector.
6. Holds the workpiece firmly and flatly against both
the table and miter gauge (if used), pushes the
workpiece into or along the sanding disc, and moves
it to different locations to wear the sandpaper
evenly and prevent it from overheating.
7. Stops the machine.
-17-
Figure 12. Removing switch key from
paddle switch.
Damage to your eyes and lungs could
result from using this machine without
proper protective gear. Always wear
safety glasses and a respirator when
operating this machine.
OPERATIONS
1. Examines the workpiece to make sure it is suitable
for sanding.
Model W1828 (For Machines Mfg. Since 4/11)
Choosing Sandpaper
Stock Inspection and
Requirements
The Model W1828 uses a 12" adhesive-backed
sanding disc.
Some workpieces are not safe or may require
modification before they are safe to sand.
Before sanding, inspect all workpieces for the
following:
There are many types of sanding discs to
choose from. We recommend aluminum oxide
for general workshop environments. Below is a
chart that groups abrasives into different classes
and shows which grits fall into each class.
Grit
24-36
40-60
80-100
Type
Very Coarse
Coarse
Medium
120-180
220-360
Fine
Very Fine
OPERATIONS
The general rule of thumb is to sand a
workpiece with progressively higher grit
numbers, with no one grit increase of more
than 50 grits at a time. Avoid skipping grits; the
larger the grit increase, the harder it will be to
remove the scratches from the previous grit.
Ultimately, the type of wood you use and your
stage of finish will determine the best grit types
to install on your sander.
-18-
•
Material Type: Sanding asbestos or
workpieces with lead paint can be
hazardous to your health. Do not sand
workpieces that contain these materials.
•
Foreign Objects: Nails, staples, dirt,
rocks and other foreign objects are often
embedded in wood. While sanding, these
objects can tear the sandpaper. Always
visually inspect your workpiece for these
items. If they can't be removed, DO NOT
sand the workpiece.
•
Excessive glue or finish: Sanding
workpieces with excess glue or finish
will load up the abrasive, reducing its
usefulness and lifespan.
Model W1828 (For Machines Mfg. Since 4/11)
Attaching Sandpaper
The Model W1828 sander uses 12" diameter pressure
sensitive adhesive-backed (PSA) sanding discs. These
are available in a variety of grits. The sandpaper can be
replaced without removing the table.
To attach the sandpaper disc, do these steps:
1. DISCONNECT MACHINE FROM POWER!
2. Peel-off the old sandpaper, and clean the disc
surface with mineral spirits, and wipe dry.
3. Peel back the protective layer on one-half of the
sandpaper disc and fold it against the remaining
half.
4. Slip the half with the protective layer between the
disc and the table edge, as shown in Figure 14.
Figure 14. Slipping covered sandpaper
between disc and table.
5. Position the exposed adhesive on the upper half of
the sandpaper disc over the aluminum disc above the
table. Once it is positioned evenly across the disc,
press the adhesive firmly onto the surface.
OPERATIONS
6. Now rotate the disc so the lower half is above the
table, peel-off the other half of the protective
paper, as shown in Figure 15, then press the
sandpaper disc firmly against the disc so adhesion is
complete.
Figure 15. Removing the paper backing.
-19-
Model W1828 (For Machines Mfg. Since 4/11)
Disc Sanding
Always keep the workpiece on the side of the wheel
that is rotating down toward the table. This will keep
the workpiece from flying out of your hands from the
rotational forces.
To use the sanding disc, do these steps:
1. DISCONNECT SANDER FROM POWER!
2. Set the angle of the table and miter gauge for your
operation. Make sure the table is about 1⁄16" away
from the sanding disc.
Figure 16. 90˚ disc sanding.
3. Connect the sander to power, turn it ON, and allow
it to reach full speed.
OPERATIONS
4. Position the workpiece on the work table against the
miter gauge.
5. With light, but firm pressure, push the workpiece
into the down-spin side of the rotating disc. See
Figures 16–18 for examples of disc sanding.
To reduce the risk of your fingers getting trapped
between the work table and sanding disc, make sure
the table is approximately 1 ⁄ 16" away from the sanding disc.
Figure 17. Miter sanding.
To prevent burning the workpiece and overloading
the sanding disc, move the workpiece slowly back
and forth from the left side of the sanding disc to the
center.
Note: To perform sanding on compound-angle cuts, tilt
the table and rotate the miter gauge to the appropriate
angles.
Figure 18. Sanding with table angled.
-20-
Model W1828 (For Machines Mfg. Since 4/11)
ACCESSORIES
Disc Sander Accessories
The following Disc Sander accessories may be available through your local Woodstock International Inc.
Dealer. If you do not have a dealer in your area, these products are also available through online dealers.
Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of dealers at:
1-800-840-8420 or at [email protected]
12" aluminum
Model
D1335
D1336
D1337
D1338 D1339
D1340
D1341 oxide PSA sanding discs are available in two packs:
Grit
60 Grit
80 Grit
100 Grit
120 Grit
160 Grit
180 Grit
220 Grit
The Shop Fox Deluxe Ceiling Mounted 3-Speed Air Cleaner, Model
W1690, is an essential machine for any shop creating dust. This
machine filters out tiny dust particles that can raise big health
concerns. Includes remote control.
-21-
OPERATIONS
The PRO-STICK® abrasive surface cleaners can extend the life of your
sanding discs. Simply press the cleaner lightly against moving sanding
discs to remove clogged-up pitch and sawdust.
Size
Model
W1304
13⁄8" x 13⁄8" x 41⁄4"
13⁄8" x 13⁄8" x 81⁄2" W1305
11⁄2" x 11⁄2" x 81⁄2" W1306
2" x 2" x 12"
W1307
Model W1828 (For Machines Mfg. Since 4/11)
MAINTENANCE
General
Regular periodic maintenance on your machine will
ensure its optimum performance. Make a habit of
inspecting your machine each time you use it.
Check for the following conditions and repair or
replace when necessary:
•
•
•
•
•
Loose mounting bolts.
Worn switch.
Worn or damaged cords and plugs.
Worn or damaged sandpaper disc.
Any other condition that could hamper the safe
operation of this machine.
Cleaning
Frequently vacuum the wood chips and sawdust from the
sander, then blow-off any remaining dust with compressed
air. This is especially important for the motor. Sawdust
build-up around the motor is a sure way to decrease its
life span.
MAINTENANCE
Table & Base
Tables can be kept rust-free with regular applications
of products like SLIPIT®. For long term storage you may
want to consider products like Boeshield T-9™.
Lubrication
Since all bearings are sealed and permanently lubricated,
simply leave them alone until they need to be replaced.
Do not lubricate them.
-22-
Make sure that your machine is
unplugged during all maintenance
procedures! If this warning is ignored,
serious personal injury may occur.
Model W1828 (For Machines Mfg. Since 4/11)
SERVICE
General
This section covers the most common service adjustments
or procedures that may need to be made during the life
of your machine.
If you require additional machine service not included
in this section, please contact Woodstock International
Technical Support at (360) 734-3482 or send e-mail to:
[email protected]
Table/Disc Parallelism
The edge of the table must be parallel with the face
of the sanding disc, and there should be a 1⁄16'' gap
between the two. This gap should be large enough so that
the sandpaper does not rub against the table, but small
enough so that the gap is not a pinch hazard.
Make sure that your machine is
unplugged during all maintenance
procedures! If this warning is ignored,
serious personal injury may occur.
Tools Needed
Qty
Wrench 10mm....................................................1
Phillips Screwdriver #2..........................................1
Fine Ruler.........................................................1
To make the table and sanding disc parallel, do these
steps:
1. DISCONNECT MACHINE FROM POWER!
2. Loosen the six flat head screws and hex nuts that
secure the table to the table support brackets.
3. Adjust the table so that there is a 1⁄16'' gap (see
Figure 19) between the 12" disc (with sandpaper
installed) and the table, from left to right.
4. When the table is parallel with the sanding disc,
tighten the flat head screws and hex nuts.
Flat Head Screws
1
⁄16" Gap
SERVICE
5. Spin the disc by hand to make sure the sandpaper is
not touching the table.
—If the sandpaper does touch the table as you spin
the disc by hand, repeat Steps 2–5 until it does
not.
6. Perform the Miter Gauge Calibration procedure
on the next page to ensure the miter slot is
perpendicular to the sanding disc.
-23-
Figure 19. Table parallel with sanding
disc.
Model W1828 (For Machines Mfg. Since 4/11)
Miter Gauge Calibration
The miter gauge should be perpendicular to the face of
the disc when it is set at 90° and mounted in the table
slot. If not, follow this procedure.
Tools Needed
Qty
Try Square or Machinist's Square..............................1
Phillips Screwdriver #1..........................................1
To calibrate the miter gauge, do these steps:
1. DISCONNECT MACHINE FROM POWER!
2. Use a try square or machinist’s square with one edge
against the face of the miter gauge and the other
against the disc face, as shown in Figure 20.
Figure 20. Squaring miter gauge to disc.
3. Loosen the lock knob on the miter gauge and adjust
the face of the miter gauge so it is flush with the
edge of the square, tighten the gauge lock knob, and
verify the setting.
4. Loosen the degree scale pointer, position the pointer
on 90˚, then re-tighten the screw.
5. Re-check the miter scale accuracy with the square.
Table Tilt Calibration
When the table tilt is set to 0˚, the table should be
positioned perpendicular to the sanding disc face. If it is
not, follow this procedure.
To calibrate the table tilt, do these steps:
1. DISCONNECT MACHINE FROM POWER!
SERVICE
2. Using a try square or machinist’s square, set one
edge on the table surface and the other against the
face of the disc, as shown in Figure 21.
3. Loosen the table tilt lock handles and adjust the
table angle until it is perfectly perpendicular to the
disc, then tighten the lock handles while holding the
table in place.
4. If the angle pointer stickers on both ends do not
point to 0˚, remove them and place them on the
trunnion so they point to 0˚.
5. Recheck the scale accuracy with the square.
-24-
Figure 21. Squaring the table.
Model W1828 (For Machines Mfg. Since 4/11)
Troubleshooting
This section covers the most common problems and corrections with this type of
machine. WARNING! DO NOT make any adjustments until power is disconnected and
moving parts have come to a complete stop!
PROBLEM
Machine does not start.
POSSIBLE CAUSE
corrective action
1. Switch disabling key removed.
2. Break or short in wiring, loose connections, plug or receptacle is corroded or miswired.
3. Power supply switched off/has
incorrect voltage.
4. Blown fuse/tripped circuit breaker
at main panel.
5. Motor connection wired incorrectly.
1. Re-install switch disabling key.
2. Trace/replace broken or corroded wires, fix loose
connections, correct wiring.
6.
7.
8.
9.
Motor ON/OFF switch at fault.
Start capacitor has blown.
Centrifugal switch at fault.
Motor at fault.
3. Switch power supply on/verify voltage.
4. Correct the cause of overload, then reset/replace
fuse or breaker.
5. Wire motor correctly (refer to inside junction box
cover).
6. Replace switch.
7. Test/replace if at fault.
8. Adjust/replace centrifugal switch.
9. Test for shorted windings or bad bearings; repair or
replace.
Machine has excessive
vibration or noise.
1. Workpiece loose or incorrectly 1. Use correct holding fixture and re-clamp
workpiece.
secured.
2. Fix/replace fan cover; replace loose or damaged
2. Motor fan rubbing on fan cover.
fan.
3. Tighten mounting bolts/nuts; use thread locking
3. Motor mounting loose.
fluid.
4. Tighten the lock handle.
4. Table tilt lock handle is loose.
5. Machine incorrectly mounted to 5. Level/shim base; tighten/adjust mounting hardware.
bench.
6. Centrifugal switch out of adjust- 6. Adjust/replace centrifugal switch.
ment; at fault.
7. Replace motor bearings or replace motor.
7. Motor bearings worn or damaged.
Machine stalls or slows
when operating.
1. Too much pressure when feeding 1. Reduce pressure when feeding workpiece.
workpiece
2. Straighten workpiece or use a different one.
2. Workpiece is warped.
3. Workpiece is incorrect for machine. 3. Only sand wood and ensure moisture is below 20%.
Miter bar loose or binds in
miter slot.
1. Miter slot dirty or gummed up.
Workpiece angle incorrect
or out of square.
1. Miter gauge or table angle not 1. Properly adjust the miter gauge and (see
Page 24).
adjusted correctly.
2. Table tilt is not calibrated cor- 2. Properly calibrate the table tilt (see Page 24).
rectly.
-25-
1. Carefully clean miter slot.
SERVICE
4. Motor connection wired incorrectly. 4. Review wiring diagram on motor cover; correct wire
connections.
5 Let cool, clean motor, and reduce workload.
5. Motor overheated.
6. Adjust/replace centrifugal switch if available.
6. Centrifugal switch at fault.
7. Test, repair, or replace motor.
7. Motor at fault.
Model W1828 (For Machines Mfg. Since 4/11)
PROBLEM
POSSIBLE CAUSE
corrective action
Sandpaper clogs quickly or 1. Sandpaper grit is too fine for the
burns.
job.
2. Workpiece is too moist.
3. Sanding depth too aggressive.
4. Paint, varnish, pitch, or other coating is loading up sandpaper.
5. Sanding soft workpiece.
1. Replace with a coarser grit sandpaper.
Glossy spots, burning, or
streaks on workpiece.
1. Use a coarser grit sandpaper.
1. Sandpaper too fine for the desired
finish.
2. Work held still for too long.
3. Workpiece is too moist.
4. Sanding stock with high residue.
5. Worn sandpaper.
6. Sanding depth too aggressive.
2. Do not keep workpiece in one place for too long.
3. Allow workpiece to dry out.
4. Use different stock. Or, accept the characteristics of
the stock and plan on cleaning/replacing sandpapers
frequently.
5. Replace sandpaper.
6. Reduce sanding depth or install coarser sandpaper.
1. Sandpaper has been stored in an 1. Store sandpaper flat and away from extremely dry,
incorrect environment.
hot, or damp conditions.
PARTS
Abrasive rubs off easily.
2. Allow workpiece to dry out.
3. Reduce sanding depth or install coarser sandpaper.
4. Install a coarse grit sandpaper, or strip coating off
before sanding.
5. Use different stock. Or, accept the characteristics
of the stock and plan on cleaning/replacing discs
frequently.
-26-
Model W1828 (For Machines Mfg. Since 4/11)
Electrical Safety Instructions
These pages are current at the time of printing. However, in the spirit of improvement, we may
make changes to the electrical systems of future machines. Study this diagram carefully. If you notice
differences between your machine and these wiring diagrams, call Woodstock International Technical
Support at (360) 734-3482.
1. SHOCKHAZARD. Working on wiring that is
connected to a power source is extremely
dangerous. Touching electrified parts will
result in personal injury including but not
limited to severe burns, electrocution,
or death. Disconnect the power from
the machine before servicing electrical
components!
5. MOTORWIRING. The motor wiring shown
in these diagrams is current at the time
of printing, but it may not match your
machine. Always use the wiring diagram
inside the motor junction box.
6. MODIFICATIONS. Using aftermarket parts or
modifying the wiring beyond what is shown
in the diagram may lead to unpredictable
results, including serious injury or fire.
2. QUALIFIEDELECTRICIAN. Due to the
inherent hazards of electricity, only a
qualified electrician should perform wiring
tasks on this machine. If you are not a
qualified electrician, get help from one
before attempting any kind of wiring job.
3. WIRECONNECTIONS. All connections must
be tight to prevent wires from loosening
during machine operation. Double-check all
wires disconnected or connected during any
wiring task to ensure tight connections.
4. WIRE/COMPONENTDAMAGE. Damaged
wires or components increase the risk of
serious personal injury, fire, or machine
damage. If you notice that any wires or
components are damaged while performing
a wiring task, replace those wires or
components before completing the task.
7. CAPACITORS/INVERTERS. Some capacitors
and power inverters store an electrical
charge for up to five minutes after being
disconnected from the power source. To
avoid being shocked, wait at least this long
before working on these components.
8. ELECTRICALREQUIREMENTS. You MUST
follow the electrical requirements at the
beginning of this manual when connecting
your machine to a power source.
9. EXPERIENCINGDIFFICULTIES. If you are
experiencing difficulties understanding
the information included in this section,
contact our Technical Support at (360) 7343482.
WIRING DIAGRAM COLOR KEY
BLUE
WHITE
BROWN
GREEN
GRAY
YELLOW
YELLOW
GREEN
PURPLE
RED
ORANGE
PINK
-27-
LIGHT
BLUE
BLUE
WHITE
TURQUOISE
SERVICE
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
color at www.shopfox.biz.
BLACK
Model W1828 (For Machines Mfg. Since 4/11)
Start
Capacitor
100MFD 265VAC
Wiring Diagram
110VAC
Motor
Ground
Motor
Junction
Box
Neutral
SERVICE
ON/OFF Switch
(viewed from behind)
Ground
Read
Page 27
STOP
Neutral
Hot
110V NEMA 5-15 Plug
(As Recommended)
Before
Wiring
-28-
-29-
PARTS
3
43
16-1
16
4
5-2
15
14
6
10
12
5-1
6
5-4
44
13
38
12 11
22-1
23
22-5
22-4
2
5-3
7
34
22
37
19
24
31
23
5-5
5
34
32
22-2 17
22-3
9
33
30
23
21
40
8
23
39
35
36
23
26
21
26
26
18
19
25
23
32
1
28
29
20
27
27-1
42
41
Model W1828 (For Machines Mfg. Since 4/11)
PARTS
Main
Model W1828 (For Machines Mfg. Since 4/11)
Main Parts List
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
1
2
3
4
5
5-1
5-2
5-3
5-4
5-5
6
7
8
9
10
11
12
13
14
15
16
16-1
17
18
19
20
21
22
X1828001
XLABEL-12
XLABEL-11
X1828004
X1828005
X1828005-1
X1828005-2
X1828005-3
XPC100C
X1828005-5
XPTLW01M
XPLW01M
X1828008
X1828009
XPW05M
X1828011
XPS09M
XPTLW02M
X1828014
XPS17M
XPSW09
XPSW09-1
X1828017
X1828018
XPFH06M
X1828020
XPN01M
X1828022
SHOP FOX LOGO LABEL
READ MANUAL LABEL
SAFETY GLASSES LABEL
MACHINE ID LABEL
MOTOR 1HP 110V 60 HZ
MOTOR FAN
FAN COVER
MOTOR JUNCTION BOX
S CAPACITOR 100M 265V 1-3/8 X 3-1/8
CAPACITOR COVER
EXT TOOTH WASHER 4MM
LOCK WASHER 5MM
WAVY WASHER 39MM
ROTATION ARROW LABEL
FLAT WASHER 4MM
GROUND INDICATOR LABEL
PHLP HD SCR M5-.8 X 10
EXT TOOTH WASHER 5MM
CORD W/PLUG
PHLP HD SCR M4-.7 X 6
PADDLE SWITCH 110/220V
SWITCH KEY
RIGHT TRUNNION
LEFT TRUNNION
FLAT HD SCR M6-1 X 20
WORK TABLE
HEX NUT M6-1
MITER GAUGE ASSEMBLY
22-1
22-2
22-3
22-4
22-5
23
24
25
26
27
27-1
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
X1828022-1
X1828022-2
X1828022-3
X1828022-4
XPS19M
XPW03M
X1828024
XPS26M
XPLW03M
X1828027
X1828027-1
X1828028
X1828029
X1828030
X1828031
X1828032
XPS47M
XPS07M
XPK23M
XP6204ZZ
X1828037
X1828038
XPSB26M
X1828040
XPS08M
XPW02M
XLABEL24
X1828044
MITER GAUGE BODY
GAUGE SLIDE
KNOB BOLT M6-.1 X 22
ANGLE POINTER
PHLP HD SCR M5-.8 X 6
FLAT WASHER 6MM
TABLE ANGLE REFERENCE LABEL
PHLP HD SCR M6-1 X 20
LOCK WASHER 6MM
COVER W/DUST CHUTE
DUST CHUTE HOSE ADAPTER
SANDING DISC WASHER 1⁄4" X 1-1⁄4"
SANDING DISC
RUBBER FOOT
STOP SCREW
TABLE LOCK LEVER ASSY
PHLP HD SCR M6-1 X 25
PHLP HD SCR M4-.7 X 8
KEY 5 X 5 X 25
BALL BEARING 6204 ZZ
BASE
SANDING DISC 80 GRIT PSA
CAP SCREW M6-1 X 12
TRUNNION REST
PHLP HD SCR M5-.8 X 12
FLAT WASHER 5MM
DISCONNECT POWER LABEL
ABRASION HAZARD LABEL
PARTS
Safety labels warn about machine hazards and how to prevent machine damage or injury. The
owner of this machine MUST maintain the original location and readability of all labels on this
machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the
machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www.
shopfoxtools.com to order new labels.
-30-
Fold along dotted lIne
place
stamp
Here
Woodstock international inc.
p.o. box 2309
bellingham, Wa 98227-2309
Fold along dotted lIne
tape along edges--please do not staple
WARRANTY
WARRANTY
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship
and materials for a period of two years from the date of original purchase by the original owner.
This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or
accidents, lack of maintenance, or reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the Shop Fox
machine or machine part, which in normal use has proven to be defective, provided that the original
owner returns the product prepaid to a Shop Fox factory service center with proof of their purchase
of the product within two years, and provides Woodstock International, Inc. reasonable opportunity to
verify the alleged defect through inspection. If it is determined there is no defect, or that the defect
resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original
owner must bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may
be implied by law, including any merchantability or fitness, for any particular purpose, are hereby
limited to the duration of this written warranty. We do not warrant that Shop Fox machinery complies
with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under
this warranty exceed the purchase price paid for the product, and any legal actions brought against
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall
in no event be liable for death, injuries to persons or property or for incidental, contingent, special or
consequential damages arising from the use of our products.
Every effort has been made to ensure that all Shop Fox machinery meets high quality and durability
standards. We reserve the right to change specifications at any time because of our commitment to
continuously improve the quality of our products.
High Quality Machines and Tools
Woodstock International, Inc. carries thousands of products designed
to meet the needs of today's woodworkers and metalworkers.
Ask your dealer about these fine products:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement