DMC | 5 Wire Analog Resistive Touchscreen FST Series | User manual | DMC 5 Wire Analog Resistive Touchscreen FST Series User manual

DMC 5 Wire Analog Resistive Touchscreen FST Series User manual
IPPC-7158 Series
15" XGA TFT LCD Industrial
Panel PC with 14 x ISA/PCI/
PICMG Slots, Passive Backplane
and Membrane Keypad
User Manual
Copyright Notice
This document is copyrighted 2008, by Advantech Co. Ltd. All rights are
reserved. Advantech Co., Ltd. reserves the right to alter the products
described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of Advantech. Information provided in this manual is intended to be accurate and reliable.
However, Advantech assumes no responsibility for use of this manual,
nor for any infringements upon the rights of third parties which may
result from such use. All brand and product names mentioned herein are
trademarks or registered trademarks of their respective holders.
Acknowledgments
IBM and PC are trademarks of International Business Machines Corporation.
For more information on this and other Advantech products, please visit
our website at:
http://www.advantech.com
For technical support and service, please visit our support website at:
http://www.advantech.com.tw/support/
Part No. 2003715800
1st Edition
Printed in Taiwan
October 2008
IPPC-7158 User Manual
ii
FCC Class A
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Warning!
Any changes or modifications made to the
equipment which are not expressly approved by
the relevant standards authority could void your
authority to operate the equipment.
iii
Packing List
Before setting up the system, check that the item is among those listed
below and is in good condition. If your Workstation does not match any
of those below, please contact your dealer immediately.
• CD ROM for IPPC Series
• Registration and 2 year Warranty card
• SATA Cable x 2
• SATA Power Cable x 2
• PATA 40 PIN DMA66 Flat Cable
• FDD cable
• D-Sub Flat Cable with bracket
• FAN power cable
• Simplified Chinese Manual
• China RoHs for IPPC-7000 series
• Jumper Bag(mini jumper*20)
IPPC-7158 Industrial Workstations includes the following models:
IPPC-7158B-X1AE: 15" XGA TFT LCD Passive Backplane Industrial
Panel PC with 14 x ISA/PCI/PICMG Slots and Membrane Keypad
IPPC-7158B-R1AE: 15" XGA TFT LCD Passive Backplane Industrial
Panel PC with 14 x ISA/PCI/PICMG Slots and Membrane Keypad and
resistive touchscreen
IPPC-7158 User Manual
iv
Additional Information and Assistance
Step 1. Visit the Advantech web site at www.advantech.com where you
can find the latest information about the product.
Step 2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional
assistance. Please have the following information ready before
you call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, application
software, etc.)
• A complete description of the problem
• The exact wording of any error messages
v
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according
to the user's manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE
THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR
ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE
EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT
TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED
BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained
herein.
IPPC-7158 User Manual
vi
Contents
Chapter
Chapter
1 General Information ....................................... 2
1.1
1.2
Introduction ....................................................................... 2
Specifications .................................................................... 3
1.3
Dimensions........................................................................ 5
1.2.1
1.2.2
1.2.3
1.2.4
1.2.5
2 System Setup.................................................... 8
2.1
A Quick Tour of IPPC-7158 ............................................. 8
2.1.1
2.1.2
2.2
2.3
Chapter
General ........................................................................... 3
System Hardware ........................................................... 3
LCD Display .................................................................. 4
Touchscreen (Optional) ................................................. 4
Environment ................................................................... 4
Figure 2.1:Open View .................................................... 9
Figure 2.2:Side View ..................................................... 9
USB Ports .................................................................... 10
Figure 2.3:Opening the Front USB Port Cover ........... 10
Adjusting the LCD Brightness ..................................... 10
Installing Optional Disk Drives....................................... 12
Rack Mounting................................................................ 12
3 Touchscreen ................................................... 14
3.1
3.2
Introduction ..................................................................... 14
Touchscreen Driver Installation & Configuration .......... 14
Appendix A LCD Specifications........................................ 16
A.1
IPPC-7158 LCD Specifications ...................................... 16
Appendix B Pin Assignments ............................................ 18
B.1
B.2
Connector Pin Definitions............................................... 19
PCI Routing Table........................................................... 22
Appendix C Keyboard Translator .................................... 24
C.1
C.2
Overview ......................................................................... 24
Programming the Front Panel Macro Keys..................... 25
vii
IPPC-7158 User Manual
viii
CHAPTER
1
General Information
This chapter gives background
information on the IPPC-7158 series
Sections include:
• Introduction
• Specifications
• Dimensions
Chapter 1 General Information
1.1 Introduction
The IPPC-7158 features a 15" TFT LCD and 14 expansion slots for PCI,
PICMG and ISAand an ATX industrial backplane to support CPU cards.
The IPPC-7158 also provides many powerful features such as detahable
front panel, front-accessible USB port, 53 membrane key & touch pad
with two mouse buttons, 6 OSD control keys, NEMA4/IP65 compliant
front panel, and optional analog resistive touchscreen (USB Interface).
Modularized Side-Open Front Panel Makes Maintenance Easy
The IPPC-7158 makes user can maintain the system fast and easily. First,
if there are problems with the LCD display, the detachable front panel
allows you to replace or service it simply and quickly. This helps saves
downtime costs associated with system crashes. Secondly, the side-open
LCD front panel also make it more convenient when you want to maintain the CPU, I/O cards, HDD, CD-ROM and even floppy.
Industrial Design Withstands Harsh Environments
In addition, the IPPC-7158 also features many powerful functions tomeet
the industrial-grade requirements. The front panel is made of Aluminum
and being chemical treated by anode. That prevents the panelfrom damaging by acid and salt. Besides, it's waterproof and IP65/NEMA4 compliant. The IPPC-7158 also offers the stainless steel chassis. It also protects
the chassis. For keeping the system working properly, the IPPC-7158 provides a fan & filter to avoid overheating & dust. In addition, the IPPC7158 also provides three mounting ways to fit different application: 19"
rack, panel or wall mounting.
IPPC-7158 User Manual
2
1.2 Specifications
1.2.1 General
• Button Control:
Membrane Keypad 1: 43 operating keys
Membrane Keypad 2: 10 programmable macro function keys
• Certifications: BSMI, CCC, CE, FCC
• Cooling System: 1 x 49 CFM fan w/50,000 hrs MTBF
• Dimensions (W x H x D):
482 x 354.8 x 162 mm (18.97" x 13.96" x 6.37")
• Disk Drive Bay:
Supports 1 x FDD, 1 x 3.5" HDD and 1 X CD-ROM (both optional)
• Enclosure: Front Panel – Aluminum,
Chassis – Anti-rust
• Mounting: Panel, 19” Rack
• Power Input: 100-240Vac, 10A, 10~50Hz
• Power Ouput: + 5V@30A, +12V@15A, +3.3V@28A, -5V@0.3A,
-12V@0.8A, +5 VSB@2A
• Power Supply: Watt :300 W, MTBF: 100,000 hrs
• Weight (Gross): 18 kg ( 39.7 lb)
1.2.2 System Hardware
• 2 x PICMG
• 10 x PCI
• 2 x ISA
3
Chapter 1
1.2.3 LCD Display
• Backlight Life: 60,000 hrs
• Contrast Ratio: 500 : 1
• Display Size: 15"
• Display Type: XGA TFT LCD
• Luminance: 250 cd/m2
• Max. Colors: 16.2 M (RGB 6-bit + FRC data)
• Max. Resolution: 1024x768
• OSD Control: ON/OFF, Brightness down, up (behind the front panel)
• Viewing Angle (H/V°): 140/120
1.2.4 Touchscreen (Optional)
• Interface: USB
• Lifespan:
10 million with silicone rubber of R8 finger, writing rate is 250g at 2X/s
• Light Transmission: > 80% (AMT)
• OS Support: Windows 95/98/ME/2000/XP/CE/NT/Vista, Linux
• Type: 8W Resistive
1.2.5 Environment
• Humidity: 5 ~ 85% RH @ 40° C (non-condensing)
• Ingress Protection: Front panel NEMA4/IP65
• Operating Temperature: 0 ~ 50° C (32 ~ 122° F)
• Storage Temperature:
-20 ~ 60° C (-4 ~ 140° F)
• Vibration Protection: 5~500 Hz,
1 GRMS random vibration (operating)
IPPC-7158 User Manual
4
1.3 Dimensions
IPPC-7158A
17
4
1
+
M3
8
5
2
0
9
___
__
7
M1
M2
”
/
6
3
_
=
M4
Esc
Delete
M5
Tab
PgDn
Back
Space
M6
Ctrl
M7
M8
Enter
Alt
Left
PgUp
Shift
Space
Right
M9
M10
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Figure 1.1: IPPC-7158 Dimensions
5
Chapter 1
IPPC-7158 User Manual
6
CHAPTER
2
System Setup
This chapter details system setup for
the IPPC-7158 Series.
Sections include:
• A Quick Tour of IPPC-7158
• Installing a CPU & CPU Cooler
• Installing Optional Disk Drives
• Rack Mounting
Chapter 2 System Setup
2.1 A Quick Tour of IPPC-7158
Before you start the computer, please follow these procedures to set up
the system.
1. Check and adjust jumpers on motherboard (optional by each CPU card)
2. Install SDRAM
3. Install CPU & CPU Cooler
4. Install add-on cards
5. Connect the wires, cables and accessories
6. Mount the computer
7. Program the BIOS settings
8. Install an operating system.
Warnings
1. The IPPC-7158B only includes the chassis and
B/P. One could use compatible CPU card to install
the system, each jumper setting and CPU chosen
based on it's own specification.
2. Switch off and unplug the computer every time
you access its interior.
3. The motherboard inside the system is composed
of many delicate ICs, chips and other integrated
circuit components. These components are easily
damaged by static shock. When you begin to install
components, please:
- Avoid touching metal parts of the motherboard.
- Wear an anti-static ring when handling a CPU or
SDRAM module.
- Put SDRAM modules and the CPU inside an
anti-static bag before installation.
4. Refer to each CPU card for BIOS setting details.
5. This machine doesn’t support USB wake function during standby mode on Windows 2000.
IPPC-7158 User Manual
8
Figure 2.1: Open View
Figure 2.2: Side View
9
Chapter 2
2.1.1 USB Ports
An external USB device may be connected to the system via the USB
ports located on the right side of the system unit and also could access
from 1 USB port on the front panel of IPPC-7158.
1.
Connect the external device to the system.
2.
The USB ports support hot plug-in connection. You should install
the device driver before you use the device.
Figure 2.3: Opening the Front USB Port Cover
2.1.2 Adjusting the LCD Brightness
The LCD OSD control key is located behind the front panel module, you
have to open the front panel to access it.
1.
Unscrew the 2 screws on the right side of front panel.
2.
Open the front panel door, to find the LCD OSD control key.
IPPC-7158 User Manual
10
2.1.3 System On/Off
The IPPC-7158 has 1 system on/off switch, located inside the chassis.
11
Chapter 2
2.2 Installing Optional Disk Drives
The IPPC-7158 provides spaces for one 3.5" hard disk drives, one CDROM drive, & one 3.5" floppy disk drive within the chassis. Front-facing
FDD & CD-ROM have already been installed. You can access them after
opening the front LCD panel.
Below is the procedure of installing HDD and CD-ROM:
1.
Unscrew the 3 screws and 4 screws on the side of the case to
remove the HDD Drive Bay
2.
Unscrew the 4 Screws on the bottom of the drive bay to separate
the 2 parts.
3.
Install HDD with 2 screws on each side.
4.
Combine the 2 sheet metal parts of the drive bay with the screws
5.
Installed the HDD drive bay finished (with CD-ROM).
2.3 Rack Mounting
The IPPC-7158B can be mounted to a 19" industrial rack.
IPPC-7158 User Manual
12
CHAPTER
2
3
Touchscreen
This chapter contains information on
the touchscreen, its installation and
configuration.
Sections include:
• Introduction
• Installing Windows 2000/XP Drivers
• Configuring PenMount Drivers
• Uninstalling PenMount Drivers
Chapter 3 Touchscreen
3.1 Introduction
The IPPC-7158 Series’ optional touchscreen uses advanced 8-wire resistive technology. It provides more accurate sensing capacity than other
technologies. The touchscreen is specially designed for tough industrial
environments, and has been approved to FCC Class B standards.
3.2 Touchscreen Driver Installation & Configuration
The touchscreen of IPPC-7158 is controlled by USB interface and has
drivers for Linux, Windows 2000, Windows XP, Windows Vista and Windows CE. You should read the instructions in this chapter carefully before
you attempt installation.
For driver installation, please insert the IPPC support CD and refer to the
path below: "D:\System Drivers\IPPC-7158B\Touch Screen Driver\DMC
6000 (Combo)\Manual\PenMount Win2K&XP&2003&Vista Universal
Driver Manual V1.02.pdf"
IPPC-7158 User Manual
14
Appendix
A
LCD Specifications
and Selection Settings
Appendix A LCD Specifications
A.1 IPPC-7158 LCD Specifications
Model
IPPC-7158
Display
15" TFT LCD
Max. resolution
1024 x 768
Colors
16.2M colors (RGB 6-bit + FRC
data)/262k(RGB 6-bit) selectable
Dot pitch (mm)
0.297 (per one triad) x 0.297
Viewing angle
140 (H), 120 (V)
Luminance
250 cd/sq meter
Viewing area
304.128 (H) x 228.096 (mm
Power consumption
10.7 W (Typ.) @ 6.0mA (Gray
Bar Pattern)
Operating temperature
0 ~ 50°C
Storage temperature
-20 ~ 60°C
Backlight MTBF
60,000 hours
.
Note:
The color LCD display installed in the IPPC is of
high quality and reliability. However, it may contain a few defective pixels which may not always
illuminate. With current technology, it is impossible to completely eliminate defective pixels.
Advantech is actively working to improve this
technology.
IPPC-7158 User Manual
16
Appendix
Pin Assignments
B
Appendix B Pin Assignments
Connector
Description
ISA1, ISA2
ISA Slot
ISA3, ISA4
PICMG connector (PCI Slot is PICMG1, PICMG2)
PICMG1, PICMG2
PICMG connector
PPCI1~PPCI3
32 bit / 33 MHz PCI slot
SPCI4~SPCI10
32 bit / 33 MHz PCI slot
KB1
KB-In or KB-Out connector (90’P)
KB2, KB3
KB-In or KB-Out connector (180’P)
KB4
KB-Out, external connector
AT1
Main AT Power connector supply +/-5V, +/-12V
ATX1
Main ATX Power connector supply +3.3V, +/-5V, +/-12V, 5VSB
BIG1
Big 4 pin Power connector supply auxiliary +5V, +12V
CN1
PS-ON Function, to CPU card for ATX power, 3 pin connector
CN2
8 pin Alarm Board Power connector
CN3
3 pin +5V and +12V Fan connector
CN4
+12V DC Fan connector
IPPC-7158 User Manual
18
B.1 Connector Pin Definitions
Pin
Definition
1
+3.3V
2
+3.3V
3
COM
4
+5V
5
COM
6
+5V
7
COM
8
Power OK
9
+5VSB (Standby)
10
+12V
11
+3.3V
12
-12V
13
COM
14
PS-ON
15
COM
16
COM
17
COM
18
-5V
19
+5V
20
+5V
KB1, KB2, KB3, KB4
Pin
Name
1
KBCLK
2
KBDATA
3
NC
4
KBGND
5
KBVCC
19
Appendix B
AT1
Pin
Name
1
NC
2
+5V
3
+12V
4
-12V
5
GND
6
GND
7
GND
8
GND
9
-5V
10
+5V
11
+5V
12
+5V
BIG1
Pin
Name
1
+12V
2
GND
3
GND
4
+5V
CN1
Pin
Name
1
PS-ON
2
GND
3
5VSB
IPPC-7158 User Manual
20
CN2
Pin
Name
1
5VSB
2
GND
3
GND
4
-5V
5
+5V
6
+3.3V
7
-12V
8
+12V
CN3
Pin
Name
1
+12V
2
GND
3
+5V
CN4
Pin
Name
1
GND
2
+12V
3
NC
21
Appendix B
B.2 PCI Routing Table
Primary PCI Group
PCI SLOT
ID SEL
PCI Interrupt Pin Route
INTA
INTB
INTC
INTD
PPCI1
P_ AD31
INTB
INTC
INTD
INTA
PPCI2
P_ AD30
INTC
INTD
INTA
INTB
PPCI3
P_ AD29
INTD
INTA
INTB
INTC
INTC
INTD
Primary PCI Group
PCI SLOT
ID SEL
PCI Interrupt Pin Route
INTA
INTB
SPCI1
P_ AD20
INTA
INTB
INTC
INTD
SPCI2
P_ AD21
INTB
INTC
INTD
INTA
SPCI3
P_ AD22
INTC
INTD
INTA
INTB
SPCI4
P_ AD23
INTD
INTA
INTB
INTC
IPPC-7158 User Manual
22
Appendix
C
Keyboard Translator
Appendix C Keyboard Translator
C.1 Overview
The keyboard translator is an interface that switches the signal from the
membrane keypad to the standard AT keyboard. There are six connectors
on the board. On top of the board, there are two connectors linking two
flat cables to the membrane keypad (as shown in Fig. 4-3). On the side of
the board, there are four connectors.
The figure below shows the keyboard translator & the cable connection
for macro keys programming details.
IPPC-7158 User Manual
24
Caution:
Keyboard Translator(KBT-2002) can't be programmed through the USB
keyboard.
The step of programming the Macro Key(M1~M10) on the front panel:
1.
Open the front panel door, use a PS/2 keyboard connect to the
reserved external keyboard terminal of KBT-2002 which on the
back of front panel (see figure below).
2.
Boot up the system and enter the BIOS, check & make sure the
USB function is disabled.( This step is to avoid the influence or
interference caused by any USB keyboard or mouse device at the
later macro keys programming process)
3.
Run the Keyboard Translator Utility Program(Main.exe) under
DOS mode by using the connected PS/2 keyboard, and then edit the
function of front panel macro keys M1~M10 then programmed the
functions into KBT-2002. (Please be notified that the SF1~SF10 in
the utility program which is exactly mapping to the macro keys
M1~M10 on the front panel, please edit the function you need
accordingly.)
C.2 Programming the Front Panel Macro Keys
The Front Panel Macro Keys (M1~M10) could be programmed to have
specific function by running the "Keyboard Translator Utility", which can
be found at IPPC-7158 CD-ROM.
You can find Keyboard Translator Utility in the IPPC User CD:
\System Drivers\IPPC-7158B\Keyboard Translator
Driver\2053xxxxxx_Utility V1.5
And follow the instruction to complete the Keyboard Translator Utility
installation.
You can find out more details about KBT-2002 in the PDF document
which located in the below path of the IPPC User CD:
D:\System Drivers\IPPC-7158B\Keyboard Translator Driver\KBT-2002
Manual_ed1.pdf
25
Appendix C
C.3 Keyboard Translator Maintenance
(KBT-2002)
Below is the procedure of replacing the keyboard translator while needed:
1.
Switch off the power, and detach the main power cord.
2.
Unscrew the screws on front panel and open the front panel door of
IPPC-7158.
3.
The Keyboard Translator will be located on the back of the front
panel, behind the mylar protect. (Seebelow)
4.
Unscrew the screws on the mylar and remove it.
5.
Remove the keypad connector protective bracket.
6.
Carefully detach all cables connected to the keyboard translator.
7.
Unscrew the four screws on the corners, pull out the keyboard
translator,and replace it. right after that, reverse the step below to
re-install all things.
IPPC-7158 User Manual
26
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising