Bosch | Art Easytrim Accu | Instruction manual | Bosch Art Easytrim Accu Instruction manual

F016 L70 456.book Seite 1 Dienstag, 20. Januar 2009 9:35 09
Originalbetriebsanleitung
Original instructions
Notice originale
Manual original
Manual original
Istruzioni originali
Oorspronkelijke
gebruiksaanwijzing
Original brugsanvisning
Bruksanvisning i original
Original driftsinstruks
Alkuperäiset ohjeet
Πρωττυπο οδηγιών
χρήσης
Orijinal iµletme talimat∂
Instrukcja oryginalna
PÛvodní návod k pouÏívání
Pôvodn˘ návod na pouÏitie
Eredeti használati utasítás
Оригинальное руководство по эксплуатации
Оригінальна інструкція з
експлуатації
Instrucøiuni originale
Оригинална инструкция
Originalno uputstvo za rad
Izvirna navodila
Originalne upute za rad
Algupärane kasutusjuhend
Instrukcijas oriinālvalodā
Originali instrukcija
Deutsch
English
Français
Español
Português
Italiano
Nederlands
Dansk
Svenska
Norsk
Suomi
Eλληνικά
Türkçe
Polski
âesky
Slovensky
Magyar
Русский
Українська
Românå
Български
Srpski
Slovensko
Hrvatski
Eesti
Latviešu
Lietuviškai
ART EASYTRIM Accu
F016 L70 456.book Seite 2 Dienstag, 20. Januar 2009 9:35 09
F 016 800 178
F 016 800 177
(ART 23/2300 EASYTRIM ACCU)
24x
2 • F 016 L70 456 • 09.01
F 016 800 183
(ART 26/2600 EASYTRIM ACCU)
F016 L70 456.book Seite 3 Dienstag, 20. Januar 2009 9:35 09
360°
14
1
2
9
3
4
10
5
11
12
6
13
7
8
3 • F 016 L70 456 • 09.01
F016 L70 456.book Seite 4 Dienstag, 20. Januar 2009 9:35 09
A
B
4
8
5
CLICK
!
➋
➊
6
CLICK!
D
C
15
CLICK
!
16
17
4 • F 016 L70 456 • 09.01
F016 L70 456.book Seite 1 Dienstag, 20. Januar 2009 9:35 09
Safety Notes
Warning! Read these instructions carefully, be
familiar with the controls and the proper use of
the trimmer. Please keep the instructions safe
for later use.
Explanation of symbols on the trimmer
General hazard safety alert.
■
■
■
Read instruction manual.
Wear eye protection.
■
■
■
360°
■
Beware of thrown or flying objects to bystanders.
Keep bystanders a safe distance away from the machine.
Remove battery before adjusting or cleaning, and
before leaving the machine unattended for any period.
Do not work in the rain or leave the trimmer
outdoors whilst it is raining.
■
■
■
■
■
■
–
■ Never operate the trimmer with damaged guards
or shields or without guards or shields in position.
Do not use the charger if the cord is damaged.
■ Before using the machine and after impact, check
for signs of wear or damage and repair if necessary.
■ Do not operate the trimmer when barefoot or
wearing open sandals, always wear substantial
footwear and long trousers.
■ Never allow children or people unfamiliar with
these instructions to use the trimmer. Local regulations may restrict the age of the operator. When
not in use store the trimmer out of reach of children.
■ This appliance is not intended for used by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of
the appliance by a person responsible for their
safety.
12 • F 016 L70 456 • TMS • 11.11.08
–
–
■
■
■
■
■
■
Children should be supervised to ensure that they
do not play with the appliance.
Never work with this trimmer while people, especially children or pets are nearby.
The operator or user is responsible for accidents
or hazards occurring to other people or their property.
Wait until the blade has completely stopped before touching it. The blade continues to rotate after the trimmer is switched off, a rotating blade
can cause injury.
Work only in daylight or in good artificial light.
Avoid operating the trimmer in wet grass, where
feasible.
Switch off when transporting the trimmer to and
from the area to be worked on.
Switch on the trimmer with hands and feet well
away from the rotating line.
Do not put hands or feet near the rotating blade.
Never fit metal cutting elements to this trimmer.
Inspect and maintain the trimmer regularly.
Have the trimmer repaired only by an authorized
customer service agent.
Always ensure that the ventilation slots are kept
clear of debris.
Switch off and remove battery from the trimmer:
whenever you leave the machine unattended for
any period
before replacing the blade
before cleaning or working on the trimmer.
Store the machine in a secure dry place out of
reach of children. Do not place other objects on
top of the machine.
Replace worn or damaged parts for safety.
Ensure replacement parts fitted are Bosch approved.
Ensure the switch is in the off position before
inserting battery pack. Inserting the battery
pack into machines that have the switch on invites accidents.
Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
Use machines only with specifically designated battery packs. Use of any other battery
packs may create a risk of injury and fire.
English - 1
F016 L70 456.book Seite 2 Dienstag, 20. Januar 2009 9:35 09
■ When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small
metal objects that can make a connection
from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
■ Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
Technical data
Trimmer
Part number (typ)
No-load speed
Cutting circle
Weight (without optional extras)
Serial Number
Battery type
Part number (typ)
Nominal Voltage
Capacity
Charging time (empty battery)
Battery charger
Part number (typ)
Charging current
Allowable charging temperature
range
ART 23 EASYTRIM ACCU/
ART 26 EASYTRIM ACCU/
ART 2300 EASYTRIM ACCU ART 2600 EASYTRIM ACCU
3 600 H78 H..
3 600 H78 J..
[min-1] 9 500
9 000
[cm]
23
26
[kg]
1.9
2.0
See serial No 14 (rating plate) on machine.
NiCd
NiCd
2 607 335 533
2 607 335 533
[V]
14.4
14.4
[Ah]
1.5
1.5
[min]
250*
250*
AL 1404
AL 1404
2 607 225 ...
2 607 225 ...
[A]
0.4
0.4
[°C]
0 – 45
0 – 45
*Charging time based on a battery charger input voltage of 230 V.
Intended Use
Delivered Items
The product is intended for the cutting of grass and
weeds under bushes, as well as on slopes and
edges that can not be reached with the lawn mower.
Intended Use is related to operation within 0 °C and
40 °C ambient temperature.
Introduction
This manual gives instructions on the correct assembly and safe use of your machine. It is important
that you read these instructions carefully.
13 • F 016 L70 456 • TMS • 11.11.08
Carefully remove the machine from its packaging
and check that you have all the following items:
– Trimmer
– Cutting guard
– Cutting disc
– Blades
– Battery charger
– Operating instructions
When parts are missing or damaged, please contact your
dealer.
English - 2
F016 L70 456.book Seite 3 Dienstag, 20. Januar 2009 9:35 09
Charging Advice
With continuous or several repetitive charging cycles without interruption, the charger can warm up.
This is not harmful and does not indicate a technical
defect of the unit.
A battery 9 that is new or has not been used for a
longer period does not develop its full capacity until
after approximately 5 charging/discharging cycles.
Leave such batteries 9 in the charging compartment 11 until they have clearly warmed up.
A significantly reduced working period after charging
indicates that the batteries are worn out and must be
replaced.
Operating Controls
1
2
3
4
5
6
7
8
9
10
11
12
13
14
On/Off switch
Handle
Guide handle
Shaft, upper
Shaft, lower
Trimmer head
Ventilation slots
Cutting guard
Rechargeable battery
Battery charger
Charging compartment
LED indicator
Mains plug**
Serial Number
Assembly
**Country specific
Not all of the accessories illustrated or described are
included as standard delivery.
For Your Safety
Warning! Switch off, remove battery from machine before adjusting or cleaning.
The blade continues to rotate for a few seconds after the trimmer is switched off.
Caution – do not touch rotating blade.
Charging Procedure
The charging procedure starts as soon as the mains
plug is plugged into the socket and the battery 9 is
inserted into the charging compartment 11.
The green LED 12 is not a charge control indicator! When the green LED is lit, it indicates that a
charging current flows.
After the end of the charging process (approx.
3 h–4 h), pull the mains plug of the battery charger
from the socket and remove the battery.
The battery should not be charged for longer
than 5.5 hours.
A temperature increase of the battery indicates that
it is fully charged.
14 • F 016 L70 456 • TMS • 11.11.08
Do not connect the battery before product
is completely assembled.
Ensure product is assemble in the following order:
A Assemble trimmer shaft
Push the upper shaft 4 and lower shaft 5 together
until a click can be heard.
Note: Once the upper and lower shaft is assembled
it can not be disassembled.
Ensure internal cable is not trapped or twisted.
B Mounting the Cutting Guard
Place the cutting guard 8 on the trimmer head 6.
➊ Hook the guard onto trimmer head and push until
secure fitting.
➋ Push rear of guard until secure (click).
C Fitting Cutting Disc/Fitting Blade
Press cutting disc 15 onto drive adaptor as shown
(click).
Fit the blade, place the blade 16 over the pivot 17
and pull outwards until it snaps into place.
English - 3
F016 L70 456.book Seite 4 Dienstag, 20. Januar 2009 9:35 09
Cutting and Edging
Maintenance
Remove stones, loose pieces of wood and
other objects from the cutting area.
The blade continues to rotate for a few seconds
after the trimmer is switched off. Allow the motor/blade to stop rotating before switching “on”
again.
Do not rapidly switch off and on.
Switching On and Off
Press switch 1 and hold depressed. Release
switch 1 for switching off.
D Cutting Grass
Move the trimmer left and right, keeping it well away
from the body.
The trimmer can efficiently cut grass up to a height
of 15 cm. Cut taller grass in stages.
Cutting Around Trees and Bushes
Carefully cut around trees and bushes so that they
do not come into contact with the cutting line.
Plants can die if you damage the bark.
Battery duration
Battery duration is dependent on the working conditions:
light conditions:
up to 500 metres
medium conditions:
up to 300 metres
tough conditions:
up to 50 metres
Before any work on the machine itself, remove battery from machine.
Note: To ensure long and reliable service, carry out
the following maintenance regularly.
Regularly check for obvious defects such as loose
fixings, and worn or damaged components.
Check that covers and guards are undamaged and
correctly fitted. Carry out necessary maintenance or
repairs before using.
If the trimmer should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorized customer service agent
for Bosch garden products.
For all correspondence and spare parts orders, always include the 10-digit part number (TYP) from
the nameplate of the machine!
Blade Maintenance
Before any work on the machine itself, remove battery from machine.
To remove the worn blade 16 push in direction of the
arrow until it snaps off the pivot 17.
Clean the pivot 17 of any residual plastic/debris with
a sharp knife.
To refit the new blade 16 place the eyelet over the
pivot 17 and pull outwards until it snaps into place.
Note: Only use Bosch replacement blades. They
have been developed specially for improved cutting
performance. The use of other cutter blades will lead
to a deterioration in performance and possible damage to the product.
After Trimming/Storage
Stop and remove battery from product. Ensure battery is removed before storage.
Clean the exterior of the machine thoroughly using a
soft brush and cloth. Do not use water, solvents or
polishes. Remove all grass and debris, especially
from the ventilation slots 7.
Turn the machine on its side and clean the cutting
guard 8 inside. If grass cuttings are compacted, remove with a wooden or plastic implement.
Battery should be stored between 0 °C – 45 °C; incorrect storage could result in the battery being
damaged.
15 • F 016 L70 456 • TMS • 11.11.08
English - 4
F016 L70 456.book Seite 5 Dienstag, 20. Januar 2009 9:35 09
Fault Finding
The following table gives checks and actions that you can perform if your machine does not operate correctly.
If these do not identify/remedy the problem, contact your service agent.
Warning: Switch off and remove battery before investigating fault.
Symptom
Possible Cause
Remedy
Can not fit Guard over
cutting disc
Incorrect assembly
Remove cutting disc and fit guard, see
also “Product assembly”
Machine fails to operate
Battery discharged
Recharge battery, see also “Charging
advice”
Machine functions
intermittently
Machines internal wiring damaged
On/Off switch defective
Contact Service Agent
Contact Service Agent
Excessive vibration/
noise
Machine fault
Blade broken
Contact Service Agent
Replace blade
Cutting time low on one
battery charge
Battery not used for long period or ini- Fully charge battery, see also “Chargtial usage
ing advice”
Grass too high
Cut in stages
Battery worn out
Replace the battery
Blade will not move
Battery discharged
Machine is not cutting
Blade broken
Battery not fully charged
Recharge battery, see also “Charging
advice”
Contact Service Agent
Machine fault
Grass entangled around cutting disc
Replace blade
Recharge battery, see also “Charging
advice“
Remove grass
No charging procedure The contacts of the battery are con- Clean the contacts (e. g. by inserting
possible due to defective taminated
and removing the battery several
battery
times) or replace the battery, as required
The battery is defective, due to a dis- Replace the battery
connection in the battery (individual
cells)
The LED indicator 12 The charger plug is not inserted (propdoes not light up after erly)
plugging the mains plug Socket, cable or charger are defective
into the socket and inserting the battery into the
charging compartment 11
16 • F 016 L70 456 • TMS • 11.11.08
English - 5
Insert the plug (fully) into the socket
Check the mains voltage and if necessary, have the battery charger
checked by an authorized customer
service station for Bosch power tools
F016 L70 456.book Seite 6 Dienstag, 20. Januar 2009 9:35 09
Disposal
Power tools, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into
household waste!
According to the European Directive
2002/96/EC on waste electrical and
electronic equipment and its incorporation into national law, products that
are no longer suitable for use must be separately
collected and sent for recovery in an environmentally-friendly manner.
After-Sales Service and
Customer Assistance
Declaration of Conformity
Our after-sales service responds to your questions
concerning maintenance and repair of your product
as well as spare parts. Exploded views and information on spare parts can also be found under:
www.bosch-pt.com
Our customer consultants answer your questions
concerning best buy, application and adjustment of
products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty.Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: + 61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Measured values determined according to
2000/14/EC (1.60 m height, 1 m distance away) and
EN ISO 5349.
Typically the A-weighted noise levels of the product
are: Sound pressure level 72 dB(A); Guaranteed
sound power level lower than 94 dB(A). Uncertainty
K = 3 dB.
The typical hand/arm vibration is below 2.5 m/s2.
We declare under our sole responsibility that the
product described under „Technical data“ is in
conformity with the following standards or standardization documents: EN 60335 (battery powered
product) and EN 60335 (battery charger) according
to the provisions of the directives 2006/95/EC,
2004/108/EC,
98/37/EC
(until 28 Dec 2009),
2006/42/EC (from 29 Dec 2009), 2000/14/EC.
2000/14/EC: Measured sound power level
88 dB(A).
Conformity assessment procedure according to Annex VI.
Notified body: SRL, Sudbury, England
Notified body identification number: 1088
Technical file at: Bosch Lawn and Garden Ltd.,
PT-LG/EAE, Stowmarket, Suffolk IP14 1EY, England
08
Leinfelden, 01.01.2008
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
Robert Bosch GmbH, Power Tools Division
Subject to change without notice
17 • F 016 L70 456 • TMS • 11.11.08
English - 6
Download PDF

advertising