Vook | H.264 Network DVR User Manual

340Z
H.264 Network DVR
User Manual
GUI Display with USB Mouse Control
Please read instructions thoroughly before operation and retain it for future reference.
For the actual display & operation, please refer to your DVR in hand.
&3'1A_BBManual_V1.1
IMPORTANT SAFEGUARD
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION:
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture. Only operate this
apparatus from the type of power source indicated on the label. The company shall not be liable for any
damages arising out of any improper use, even if we have been advised of the possibility of such
damages.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying
the appliance.
All lead-free products offered by the company comply with the requirements of the European law
on the Restriction of Hazardous Substances (RoHS) directive, which means our manufacture
processes and products are strictly “lead-free” and without the hazardous substances cited in the
directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must
be collected separately at the product end-of-life. This applies to your product and any
peripherals marked with this symbol. Do not dispose of these products as unsorted municipal
waste. Contact your local dealer for procedures for recycling this equipment.
This apparatus is manufactured to comply with the radio interference requirements.
Disclaimer
The information in this manual was current when released. We reserve the right to revise or remove any content in
this manual at any time. We do not warrant or assume any legal liability or responsibility for the accuracy,
completeness, or usefulness of this manual. For the actual display & operation, please refer to your DVR in hand.
The content of this manual is subject to change without notice.
The product & company names mentioned herein may be the registered trademarks or tradenames of their
respective owners.
Grounding
This is a Safety Class 1 Product (provided with a protective earthing ground incorporated in the power cord). The
mains plug shall only be inserted in a socket outlet provided with a protective earth contact. Any interruption of the
protective conductor inside or outside of the instrument is likely to make the instrument dangerous. Intentional
interruption is prohibited.
Water & Moisture
Do not expose this product to dripping or splashing and that no objects filled with liquids, such as vases, shall be
placed on the product.
MPEG4 Licensing
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE
WITH THE MPEG-4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG-4 VIDEO THAT
WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR
WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO
LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION
INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING
MAY BE OBTAINED FROM MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM.
GPL Licensing
This product contains codes which are developed by Third-Party-Companies and which
are subject to the GNU General Public License (“GPL”) or the GNU Lesser Public License
(“LGPL”).
The GPL Code used in this product is released without warranty and is subject to the
copyright of the corresponding author.
Further source codes which are subject to the GPL-licenses are available upon request.
We are pleased to provide our modifications to the Linux Kernel, as well as a few new
commands, and some tools to get you into the code. The codes are provided on the FTP
site, and please download them from the following site or you can refer to your distributor:
ftp://ftp.dvrtw.com.tw/GPL/AV074/
Version
Firmware: 1019-1008-1010-1010
TABLE OF CONTENTS
1. BEFORE USING THIS DVR .........................................................................1
1.1 Package Content ......................................................................................................... 1
1.2 Front Panel .................................................................................................................. 1
1.3 Rear Panel ................................................................................................................... 3
2. CONNECTION AND SETUP ........................................................................5
2.1 SATA HDD Installation.................................................................................................. 5
2.2 Camera Connection ..................................................................................................... 7
2.2.1 Normal Camera Connection ................................................................................ 7
2.2.2 PTZ Camera Connection ..................................................................................... 8
2.3 DVR Power On ............................................................................................................ 9
2.4 Date and Time Setting................................................................................................ 10
2.5 Clear Hard Disk.......................................................................................................... 10
2.6 Password Setting ....................................................................................................... 11
3. GUI DISPLAY WITH USB MOUSE CONTROL..........................................12
3.1 Connect USB Mouse.................................................................................................. 12
3.2 Quick Menu Bar ......................................................................................................... 12
3.2.1 Channel Switch.................................................................................................. 13
3.2.2 PTZ Control Panel ............................................................................................. 13
3.3 Main Menu ................................................................................................................. 14
4. BASIC OPERATION...................................................................................15
4.1 Live Page ................................................................................................................... 15
4.2 Record Icon................................................................................................................ 15
4.3 Playback .................................................................................................................... 16
4.3.1 Playback Control................................................................................................ 16
4.3.2 Event Search ..................................................................................................... 17
4.3.3 Audio Playback .................................................................................................. 17
4.4 User Level Switch ...................................................................................................... 17
4.5 Video Output Switch................................................................................................... 17
5. FREQUENTLY-USED FUNCTIONS ...........................................................19
5.1 Quick Search ............................................................................................................. 19
5.2 Record ....................................................................................................................... 19
5.2.1 Quick record setting........................................................................................... 19
5.2.2 Detailed record setting....................................................................................... 20
5.3 Schedule Setting ........................................................................................................ 21
5.3.1 Record Timer ..................................................................................................... 21
5.3.2 Detection Timer.................................................................................................. 22
5.4 Detection Setting........................................................................................................ 22
5.5 PTZ Camera Setting .................................................................................................. 23
5.6 System Setting........................................................................................................... 24
5.6.1 Password Setting............................................................................................... 24
5.6.2 System Upgrade ................................................................................................ 25
5.6.3 Video Backup..................................................................................................... 25
5.6.4 Clear All HDD Data ............................................................................................ 27
5.7 Network...................................................................................................................... 27
6. REMOTE OPERATION...............................................................................29
6.1 Supplied Licensed Software....................................................................................... 29
6.1.1 Installation & Network Connection ..................................................................... 29
6.1.2 Control Panel Overview ..................................................................................... 31
6.1.3. General Operation ............................................................................................ 33
6.1.4. E-Map ............................................................................................................... 36
6.2 IE Web Browser ......................................................................................................... 41
6.2.1 Event Playback & Download.............................................................................. 43
APPENDIX 1 SPECIFICATIONS....................................................................44
APPENDIX 2 COMPATIBLE USB FLASH DRIVE LIST ................................48
APPENDIX 3 COMPATIBLE SATA HDD LIST...............................................49
APPENDIX 4 MAIN MENU STRUCTURE......................................................50
APPENDIX 5 DVR BATTERY REPLACEMENT ............................................52
APPENDIX 6 PIN CONFIGURATION.............................................................53
APPENDIX 7 DVD WRITER INSTALLATION ................................................56
BEFORE USING THIS DVR
1. BEFORE USING THIS DVR
1.1 Package Content
16CH / 8CH Model
DVR
HDD screws
IR Remote Controller
Manual for IR Remote Controller
IR Receiver Extension Cable
CD Manual
Adapter & Power cord
USB Mouse
25 Pin DSUB Connector
4CH Model
DVR
HDD screws
IR Remote Controller
Manual for IR Remote Controller
CD Manual
Adapter & Power cord
1.2 Front Panel
1)
LED Indicators
HDD is reading or recording.
An alarm is triggered.
Timer recording is on.
Under playback status.
DVR is powered on.
2)
(▲) / (▼) / (◄) / (►)
Press ▲ / ▼ / ◄ / ► to move up / down / left / right.
In the playback mode:
Press “” to pause playback.
Press “” to stop playback.
Press ““ to fast forward.
Press ““ to fast rewind.
3)
MENU
Press “MENU” to enter the main menu.
4)
ENTER
Press “ENTER” to confirm the setting.
5)
LIST (Event List Search)
Press to quickly search the recorded files by four event lists: RECORD LIST / MOTION
LIST / ALARM LIST / TIME LIST, or select FULL LIST to show all the event logs.
To quickly search the time you want, select “QUICK SEARCH”. Set the time range you
want, and select “Start” to play the recorded video clip during the specified time.
1
BEFORE USING THIS DVR
6)
PLAY
Press to playback the latest recorded data.
7)
SLOW
In the playback mode, press to show slow playback.
8)
ZOOM
Press to enlarge the picture of selected channel in the FRAME or FIELD recording
mode.
9)
SEQ
Press to display each channel in full screen one by one starting from CH1. When the last
channel is displayed, it will repeat from CH1 again. To exit this mode, press “SEQ”
again.
10)
Press to show the 4-channel display mode.
11) CH1 ~ 16 / 1 ~ 8 / 1 ~ 4
Press the channel number keys to select the channel to display.
12) SEARCH
Press to enter the time search menu. Set the time range you want, and select “START”
to play the recorded video clip during the specified time.
13) AUDIO (SLOW + ZOOM)
Press “SLOW” + “ZOOM” to select live or playback audio from audio channel 1~4.
Live audio from audio channel 1~4
(indicated in white)
Playback audio from audio channel 1~4
(indicated in yellow)
Audio channel unselected
14) P.T.Z. (
Press “
+ SEQ)
” + “SEQ” at the same time to enter / exit the PTZ control mode.
15) USB port
There are two USB ports on the front panel, one for connecting your USB mouse for
mouse control, and the other one for connecting your USB flash drive for video backup.
Note: It’s not allowed to have two USB mice or two USB flash drives connected on
the front panel.
For the compatible USB flash drive list, please refer to “APPENDIX 2 COMPATIBLE
USB FLASH DRIVE LIST” at page 48.
16)
(For selected models only)
Press “ ” to open / close the DVD writer.
2
BEFORE USING THIS DVR
1.3 Rear Panel
1)
75Ω / HI-IMPEDANCE (For Selected Models Only)
When using Loop function, please switch to HI-IMPEDANCE. When you don’t use Loop
function, please switch to 75Ω.
2)
VIDEO IN (1 ~ 16 / 1 ~ 8 / 1 ~ 4): Connect to the video connector of a camera.
VIDEO LOOP (1 ~ 16 / 1 ~ 8): Video output connector. (For Selected Models Only)
Note: The DVR will automatically detect the video system of the camera, please
make sure that the cameras are properly connected to the DVR and
power-supplied before the DVR is turned on.
3)
AUDIO IN (1 ~ 4)
Connect to the audio connector of a camera if the camera supports audio recording.
Note: To make a video backup with audio, make sure the camera which supports
the audio function is connected to the video-in channel and audio-in
channel. For example, the audio data from audio CH1 will be recorded with
the video data from video CH1.
4)
AUDIO OUT
Connect to a speaker with 1 mono audio output.
Note: To know how many audio outputs your DVR supports, please refer to its
specifications.
5)
MONITOR
Connect to a CRT monitor for video output.
Note: When both MONITOR and VGA are connected, press the left key ◄ on the
DVR front panel during DVR power-on to force the video output via
MONITOR. For details, please refer to “4.5 Video Output Switch” at page 17.
6)
CALL (For Selected Models Only)
Connect to a monitor specific for sequence display.
7)
VGA
Connect to a LCD monitor directly.
Note: When both MONITOR and VGA are connected, press the right key ► on the
DVR front panel during DVR power-on to force the video output via VGA.
For details, please refer to “4.5 Video Output Switch” at page 17.
8)
IR (For Selected Models Only)
Connect the IR receiver extension line for remote control.
9)
EXTERNAL I/O
This port is used to connect external devices (such as speed dome cameras or external
alarm, etc).
3
BEFORE USING THIS DVR
For detailed I/O port PIN configuration, please refer to “APPENDIX 6 PIN
CONFIGURATION” at page 53.
10) LAN
Connect to Internet by LAN cable.
11) DC 19V
Connect to the supplied adapter.
12)
Power Switch
Switch to “\” to turn on the power, and “|” to turn off the power.
4
CONNECTION AND SETUP
2. CONNECTION AND SETUP
Before the DVR is powered on, make sure you have installed a hard disk and connected
at least one camera. For details, please refer to the following sections.
Note: The DVR is designed to automatically detect the video system of the
connected cameras (NTSC or PAL). To make sure the system detection is
correct, please check if the cameras are connected to the DVR and
power-supplied before the DVR is powered on.
2.1 SATA HDD Installation
A SATA HDD must be installed before the DVR is powered on.
Note: It’s recommended to clear all data in the hard disk when the DVR is
powered on and the date & time are set correctly to ensure the recorded
data are not mixed with other data previously saved in the same hard disk.
For details, please refer to “5.6.4 Clear All HDD Data” at page 27.
For 16CH & 8CH Models
Step1: Loose the screws on the upper cover and open the upper cover of the DVR.
Note: The DVR cover is made of metal. Please be careful with its edge when you
remove the cover.
Step2: There are two HDD brackets
for this DVR as indicated on
the right picture.
2-1 To install on the first bracket
Remove the bracket, and align
the screw holes of the bracket
with the HDD’s screw holes. Make
sure the PCB side of the HDD is
facing up.
Fasten the HDD to the bracket,
and connect the power connector
and data bus connector to the
HDD. Then, replace the bracket to
DVR.
5
CONNECTION AND SETUP
2-2 To install on the second bracket
Connect the power connector and
data bus connector to the HDD.
When connecting the power
cable, make sure the cable is
passed through the power cable
of DVD writer. This is to prevent
the HDD power cable from
interfering with the fan spinning.
Align the screw holes of the
bracket with the HDD’s screw
holes. Make sure the PCB side of
the HDD is facing up. Then,
fasten the HDD to the bracket.
Note: For DVD writer installation, please refer to “APPENDIX 7 DVD WRITER
INSTALLATION” at page 56.
Step3: Close the upper cover of the DVR, and fasten all the screws you loosened in
Step1.
For 4CH Model
Step1: Loose the screws on the upper cover and remove it from the DVR. Find the two
HDD brackets located on the DVR base.
Step2: Get a compatible HDD, and connect it to the power connector and data bus
connector.
Step3: Make sure the PCB side is facing up, and place the HDD between the HDD
brackets on the DVR base as shown below.
Make sure the other side of the HDD is contacted with the DVR base for
heat conduction.
6
CONNECTION AND SETUP
Step4: Align the screw hole on the each bracket with the screw hole on the each side of
the HDD as shown below, and fix the HDD to the bracket with a HDD screw
supplied.
Step5: Close the upper cover of the DVR, and fasten all the screws you loosened in Step 1.
2.2 Camera Connection
The cameras must be connected and power-supplied before the DVR is powered on.
Connect the camera with the indicated power supply. Then, connect the camera video
output to the DVR video input port with a coaxial cable or RCA cable with BNC
connectors.
Note: For detailed DVR video input ports, please refer to “1.3 Rear Panel” at page
3.
2.2.1 Normal Camera Connection
Note: For detailed camera installation and connection, please refer to its own user
manual.
1) Connecting to DVR video input
Connect the camera video output to the DVR video input port with a coaxial cable or
RCA line with BNC connector.
2) Connecting to DVR audio input (Optional)
Connect the camera audio output to the DVR audio input port with a coaxial cable or
RCA cable with BNC connectors.
7
CONNECTION AND SETUP
3) Connecting to power
Connect the camera with indicated power supply and make sure it’s power-supplied.
2.2.2 PTZ Camera Connection
The following description is taking our brand’s PTZ camera as an example.
For DVR setting to control the PTZ camera, please refer to “5.5 PTZ Camera Setting” at
page 23. For detailed PTZ camera control and operation, please refer to its own user
manual.
RJ11 cable
RS485-A: Red wire
RS485-B: Green wire
The RJ11 cable is not supplied in the sales package.
STEP 1: Get a RJ11 cable with the proper length to your connection.
Different RJ11 connector may have different wire layout, so the connection
might be different. If you cannot control the DVR after connection, please
reverse the RJ11 cable connection with the DVR.
STEP 2: Remove one end of the insulating coating of the RJ11 cable.
Remove one end of the insulating coating of the RJ11 cable to find the
RS485-A and the RS485-B wires, and remove the insulating coating to reveal
the naked wires for further connection.
STEP 3: Twist the RS485-A and RS485-B wires of the RJ11 cable and the speed
dome camera together.
Twist the RS485-A (red) and RS485-B (green) wires of the RJ11 cable to the
RS485-A (brown) and RS485-B (orange) wires of the speed dome camera. To
protect the naked wires, use the insulation tape to cover on the twisted wires.
STEP 4: Connect the other end of the RJ11 cable to DVR.
Solder the RS485-A (red) and RS485-B (green) wires of the RJ11 cable to the
corresponding pins on the solder side of the optional D-Sub connector.
8
CONNECTION AND SETUP
For DVR PIN configuration, please refer to “APPENDIX 6 PIN
CONFIGURATION” at page 53. For connection details, please check with your
installer.
STEP 5: Set the speed dome camera at the DVR side.
Go to “ADVANCE CONFIG” l “REMOTE” to set the speed dome camera.
a) Select the device to “PTZ”.
b) Set the ID to the value the same as the one set in the speed dome camera.
The default ID of the camera is 000.
c) Select the protocol to “NORMAL”.
d) Set the baud rate to the value the same as the one set in the speed dome
camera. The default baud rate of the camera is 2400.
ADVANCE CONFIG
CANERA
DETECTION
ALERT
NETWORK
SNTP
DISPLAY
RECORD
REMOTE
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 W
DEVICE
PTZ
ID
000
PROTOCOL
NORMAL
RATE
2400
X
EXIT
2.3 DVR Power On
This device should be operated only with the type of power source indicated on the
manufacturer’s label. Connect the indicated AC power cord to the power adapter, and
plug into an electrical outlet. The power LED will be on.
Note: Before the DVR is powered on, make sure the cameras are connected and
power-supplied for the detection of the camera video system to be correct.
Note: To ensure that your DVR works constantly and properly, it's recommended
to use an UPS, Uninterruptible Power Supply (Optional), for continuously
operation.
9
CONNECTION AND SETUP
2.4 Date and Time Setting
Before operating your DVR, please set the date and time on your DVR FIRST.
Note: Please DO NOT change the date or time of your DVR after the recording
function is activated. Otherwise, the recorded data will be disordered and
you will not be able to find the recorded file to backup by time search. If
users change the date or time accidentally when the recording function is
activated, it’s recommended to clear all HDD data, and start recording
again.
Note: For the first time to use the DVR, please power it on for at least 48 hours
continuously after the date & time is set correctly. It helps to prevent DVR
time from resetting after the disconnecting of DVR power. If the DVR time
resets after the disconnecting of DVR power, for example, caused by a
power outage, the battery might run out and please replace the battery as
described in “APPENDIX 5 DVR BATTERY REPLACEMENT” at page 52.
Right-click to enter the DVR password with the password keypad. The default
administrator password is 0000. The status will be changed from
(key lock) to
(administrator). Then, right-click to show the main menu, and select “QUICK START”
“TIME SETUP” to set the date & time.
QUICK START
GENERAL
TIME SETUP
DATE
TIME
2009 / NOV / 17
15 : 35 : 53
EXIT
2.5 Clear Hard Disk
It’s recommended to clear all data in the hard disk for the first time to user this DVR to
ensure the recorded data are not mixed with other data previously saved in the same
hard disk.
Right-click to show the main menu, and select “SYSTEM”
“SYSTEM INFO”
“CLEAR HDD”. The DVR will reboot when HDD data are cleared.
10
CONNECTION AND SETUP
SYSTEM
TOOLS
SYSTEM INFO
USB BACKUP
DVD BACKUP
BAUD RATE
HOST ID
R.E.T.R
AUTO KEY LOCK
CLEAR HDD
RESET DEFAULT
REMOTE CONTROL ID
2400
000
5
NEVER
HDD-0
SUBMIT
000
SERIAL TYPE
RS485
VIDEO FORMAT
NTSC
VERSION
1019-1008-1010-1010
EXIT
2.6 Password Setting
Right-click to show the main menu, and select “SYSTEM”
DVR password.
“TOOLS” to change the
There are two user levels: ADMIN & OPERATOR. For details, please refer to “4.4 User
Level Switch” at page 17.
SYSTEM
TOOLS
SYSTEM INFO
USB BACKUP
DVD BACKUP
LANGUAGE
ADMIN PASSWORD
OPERATOR PASSWORD
UPGRADE
EXIT
11
ENGLISH
SETUP
SETUP
SUBMIT
GUI DISPLAY WITH USB MOUSE CONTROL
3. GUI DISPLAY WITH USB MOUSE CONTROL
3.1 Connect USB Mouse
Connect your USB mouse to one of the USB ports on the DVR front panel, and check if
there’s a mouse icon (
) on the screen, indicating the USB mouse is detected properly.
Move your mouse to enter the DVR password with the password keypad. The default
administrator password is 0000. The status will be changed from
(key lock) to
(administrator), and the quick menu bar appears on the left side of the screen.
Note: There are two user levels for DVR access which can be set in the main menu
“SYSTEM” “TOOLS”. For details, please refer to “4.4 User Level Switch” at
page 17.
Password Input
Quick Menu: Close
3.2 Quick Menu Bar
Move to the arrow mark to extend the quick menu bar and show the five functions as
follows:
Quick Menu: Open
Click to show the channel switch panel and
select the channel you want. For details,
please refer to “3.2.1 Channel Switch” at page
13.
Click to display the playback control panel,
and click
to play the latest recorded video
clip, or click
to enter the search list. For
details, please refer to “4.3 Playback” at page
16.
Switch to the channel you want first, and click
to enter the zoom-in mode. In this mode,
click and drag the red frame on the bottom left
of the screen to move to the place you want to
see. To exit this mode, click 7.
12
GUI DISPLAY WITH USB MOUSE CONTROL
Click to select the audio channel you want:
In the live mode, only the live audio channels
can be selected.
In the playback mode, live and playback
audio channels can be selected.
Click to enter the PTZ mode and show the
PTZ camera control panel. For details, please
refer to “3.2.2 PTZ Control Panel” at page 13.
3.2.1 Channel Switch
Click
on the quick menu bar to display the panel as follows:
Note: The buttons available depend on the model you have.
1~16
Video Channel Number
Click to switch to the channel you want in full screen.
Sequence Display
Click to display each channel in full screen one by one starting
from CH1. When the last channel is displayed, it will repeat from
CH1 again.
When this function is on,
will be shown on the status bar.
Quad Display
Press to show the 4-channel display mode.
9-Cut Display
Press to show the 9-channel display mode.
16-Cut Display
Press to show the 16-channel display mode.
3.2.2 PTZ Control Panel
Note: In the PTZ control mode, hot point is supported to move the camera view to
the specified point after a click.
Click
on the quick menu bar to display the panel as follows:
13
GUI DISPLAY WITH USB MOUSE CONTROL
/
/
/
Camera Menu
Click to enter the camera main menu.
For details about each camera menu, please refer to its
own user manual.
Enter
Click to confirm your selection / enter the menu.
Up / Down / Left /
Click to move your selection up / down / left / right, or
change settings.
Right
/
Zoom in / out max
Click to zoom in on the image to the largest / zoom out
on the image to its original size.
/
Zoom in / out
Click to zoom in / out the image.
/
Focus near / far
Click to adjust the focus of the image.
Auto mode
Click to activate the auto function.
Before using it, you need to assign a specific function
that will be enabled when “AUTO” is clicked. For
details, please refer to the user manual of the PTZ
camera.
Preset point
Click to enter the PTZ preset point you want to see.
3.3 Main Menu
Right-click anywhere on the screen to show the main menu as follows, and right-click
again to exit.
For details about the menu structure, please refer to “APPENDIX 4 MAIN MENU
STRUCTURE” at page 50.
Main Menu
QUICK START
Click to set the status display, image
settings, and date & time.
DATE SETUP
Click to set the date display and
daylight saving.
SYSTEM
Click to set the system configurations.
EVENT
INFORMATION
Click to enter the event search menu.
ADVANCE
CONFIG
Click to set CAMERA, DETECTION,
ALERT, NETWORK, SNTP, DISPLAY,
RECORD and REMOTE.
SCHEDULE
SETTING
Click to set record timer and detection
timer.
14
BASIC OPERATION
4. BASIC OPERATION
4.1 Live Page
Icon
Function
Icon
Function
Icon
Function
Live audio channel (1~4)
Playback audio channel
(1~4)
Audio channel off
Digital zoom on
Digital zoom off
Timer recording
Network disconnected
Internet connected
LAN connected
USB mouse connected
USB flash drive / device
connected
No USB device
connected
Key lock
PTZ mode on
HDD overwrite
Administrator
Operator
Sequence
Motion
Recording
Alarm
4.2 Record Icon
1)
Manual Recording
By defaults, manual recording is on (
installed.
2)
) when the DVR is powered on and a HDD is
Event Recording
When the motion detection or alarm is on, the motion icon (
on the screen for any motion or alarm event.
3)
) shows
Timer Recording
When timer recording is on, you will see “
4)
) or alarm icon (
” on the screen.
HDD Overwritten
Be defaults, the HDD overwritten function is set to ON, and “
screen.
15
” will be shown on the
BASIC OPERATION
4.3 Playback
Click “
” on the quick menu bar to display the playback control panel, and click
play the latest recorded video clip, or click
to
to enter the search list.
Note: There must be at least 8192 images of recorded data for playback to work
properly. If not, the device will stop playback. For example, if the IPS is set
to 30, the recording time should be at least 273 seconds (8192 images / 30
IPS) for the playback to work properly.
Note: During playback, the image size of the recording (FRAME, FIELD or CIF) will
be shown on the screen.
4.3.1 Playback Control
Fast Forward
Increase the speed for fast forward. Click once to get 4X
speed forward and click twice to get 8X speed, etc., and
the maximum speed is 32X.
Fast Rewind
Increase the speed for fast rewind. Click once to get 4X
speed rewind and click twice to get 8X speed, etc., and the
maximum speed is 32X.
Click to play the latest recorded video clip immediately,
and click again to pause.
/
Play / Pause
In the pause mode, click
forward, and click
/
once to get one frame
to get one frame rewind.
Stop
Click to stop the video playback.
Slow Playback
Click once to get 1/4X speed playback, and click twice to
get 1/8X speed playback.
Previous /
Next Hour
Click to jump to the next / previous time interval in an hour,
for example, 11:00 ~ 12:00 or 14:00 ~ 15:00, and start
playing the earliest event video clip recorded during this
whole hour.
16
BASIC OPERATION
4.3.2 Event Search
Click
to quickly search the recorded files by four event lists: RECORD LIST /
MOTION LIST / ALARM LIST / TIME LIST, or select FULL LIST to show all the event
logs.
To quickly search the time you want, select “QUICK SEARCH”. Set the time range you
want, and select “Start” to play the recorded video clip during the specified time.
4.3.3 Audio Playback
In the playback mode, click
on the quick menu bar as many times as needed to
select live or playback audio from audio channel 1~4.
Live audio from audio channel 1~4
(indicated in white).
Playback audio from audio channel 1~4
(indicated in yellow).
Audio channel unselected
Note: To make a video backup with audio, make sure the camera which supports
the audio function is connected to the video-in channel and audio-in
channel. For example, the audio data from audio CH1 will be recorded with
the video data from video CH1.
4.4 User Level Switch
In the key lock mode ( ), move your USB mouse to display the password input keypad.
There are two user levels for accessing the DVR: Administrator ( ) & Operator ( ).
When the administrator password is entered,
will be shown on the status bar of the
screen and all operations are allowed. The default administrator password is 0000.
When the operator password is entered,
will be shown on the status bar of the
screen, and the main menu is NOT allowed to access. The operator user level needs to
be set in the main menu “SYSTEM”
“TOOLS”.
To switch between these two user levels, click the current user level icon to switch to the
key lock mode, and move your mouse to show the password input keypad, and enter the
password of the user level you want.
4.5 Video Output Switch
It’s not allowed to have video output simultaneously on a CRT monitor (connected to
“MONITOR”) and LCD monitor (connected to “VGA”).
17
BASIC OPERATION
The default video output setting is “AUTO”, meaning the DVR will automatically detect
the video output source. When “VGA” and “MONITOR” are both connected, the default
monitor output is VGA.
To change the video output setting manually:
To force the video output via “MONITOR”, press the left key ◄ on the DVR front panel at
DVR power-on.
To force the video output via “VGA”, press the right key ► on the DVR front panel at DVR
power-on.
The setting is changed when you hear a short beep sound.
OR:
When the DVR is powered on and initialized, right-click to show the main menu, and
select “ADVANCE CONFIG”
“DISPLAY”
“DISPLAY OUTPUT PATH”.
Select “VGA” to switch to the connected LCD monitor, or “COMPOSITE” to switch to the
connected CRT monitor. The DVR will then reboot for the change to take effect.
ADVANCE CONFIG
CAMERA
DE-INTERLACE (For Selected Models Only)
OFF
DETECTION
SCREEN DWELL DURATION
03
ALERT
VGA OUTPUT
1024 X 768
NETWORK
DISPLAY COVERT
ON
SNTP
HDD DISPLAY MODE
HDD SIZE
DISPLAY
DISPLAY OUTPUT PATH
AUTO
RECORD
ALPHA BLENDING
200
REMOTE
EXIT
18
FREQUENTLY-USED FUNCTIONS
5. FREQUENTLY-USED FUNCTIONS
5.1 Quick Search
Press “SEARCH” on the DVR front panel to enter the time search menu as follows:
QUICK SEARCH
DATE
TIME
HARD DISK
SEARCH
1)
2009/NOV/20
15:17:57
ALL HDD
START
DATE / TIME
Select the date & time within which includes the data you want.
2)
HARD DISK
Select the hard disk including the video data you want to search, or select “ALL
HDD”.
3)
SEARCH
Click “SUBMIT” to start search and play the video data immediately.
5.2 Record
5.2.1 Quick record setting
Right-click to display the main menu, and select “QUICK START”
“GENERAL”.
QUICK START
GENERAL
TIME SETUP
CHANNEL TITLE
EVENT STATUS
DATE DISPLAY
IMAGE SIZE
QUALITY
IMAGE PER SECOND
ON
ON
ON
CIF
SUPER BEST
120
EXIT
1)
IMAGE SIZE
Select one of the image sizes: FRAME, FIELD or CIF.
2)
QUALITY
Select one of the 4 quality options: SUPER BEST, BEST, HIGH & NORMAL.
19
FREQUENTLY-USED FUNCTIONS
3)
IMAGE PER SECOND
Select the images per second for MANUAL RECORD.
5.2.2 Detailed record setting
Right-click to display the main menu, and select “ADVANCE CONFIG”
“RECORD”.
Note: Please DO NOT change the date or time of your DVR after the recording
function is activated. Otherwise, the recorded data will be disordered and
you will not be able to find the recorded file to backup by time search. If
users change the date or time accidentally when the recording function is
activated, it’s recommended to clear all HDD data, and start recording
again.
ADVANCE CONFIG
CAMERA
DETECTION
ALERT
NETWORK
SNTP
DISPLAY
RECORD
REMOTE
MANUAL RECORD ENABLE
EVENT RECORD ENABLE
TIMER RECORD ENABLE
EVENT RECORD IPS
TIMER RECORD IPS
PRE-ALARM RECORD
OVERWRITE
EVENT RECORD ALL CHANNEL
KEEP DATA LIMIT (DAYS)
ON
ON
ON
120
120
ON
ON
OFF
OFF
EXIT
1)
MANUAL RECORD ENABLE
Set the manual recording function on / off.
2)
EVENT RECORD ENABLE
Set the event recording function on / off.
3)
TIMER RECORD ENABLE
Set the timer recording function on / off.
4)
EVENT RECORD IPS
Select the images per second for EVENT RECORD (Recording that is triggered by
alarm or motion).
5)
TIMER RECORD IPS
Select the images per second for TIMER RECORD (Recording that is activated
according to the scheduled time).
6)
PRE-ALARM RECORD
Select to enable or disable the pre-alarm function (ON / OFF).
When pre-alarm and event recording functions are both activated, the DVR will
20
FREQUENTLY-USED FUNCTIONS
record 8MB data before an alarm / motion event is triggered.
7)
OVERWRITE
Select “ON” to overwrite previous recorded data in your HDD when the HDD is full.
When this function is on and the HDD is full, the DVR will clear 8GB data from the
oldest for continuous recording without notice.
8)
EVENT RECORD ALL CHANNEL
Select to record all channels (ON) or record the channel with an event only (OFF)
for any event.
9)
KEEP DATA LIMIT (DAYS)
Assign the maximum recording days from 01 to 31 after which all the recorded data
will be removed, or select “OFF” to disable this function.
5.3 Schedule Setting
Right-click to display the main menu, and select “SCHEDULE SETTING”.
5.3.1 Record Timer
Click “RECORD”. In “RECORD TIMER”, select “ON” to enable record timer, and select
the day and time for this function.
SCHEDULE SETTING
RECORD
DETECTION
RECORD TIMER
0
2
ON
4
6
8
10
12
SUN
MON
TUE
WED
THU
FRI
SAT
EXIT
X axis
Y axis
0 ~ 24 hours. Each time bar is 30 minutes.
Monday ~ Sunday.
21
14
16
18
20
22
24
FREQUENTLY-USED FUNCTIONS
5.3.2 Detection Timer
Click “DETECTION”. In “DETECTION TIMER”, select “ON” to enable record timer, and
select the day and time for this function.
SCHEDULE SETTING
RECORD
DETECTION
DETECTION TIMER
0
2
4
ON
6
8
10
12
14
16
18
20
22
24
SUN
MON
TUE
WED
THU
FRI
SAT
EXIT
X axis
Y axis
0 ~ 24 hours. Each time bar is 20 minutes.
Monday ~ Sunday.
5.4 Detection Setting
Right-click to display the main menu, and select “ADVANCE CONFIG”
“DETECTION”.
ADVANCE CONFIG
CANERA
DETECTION
ALERT
NETWORK
SNTP
DISPLAY
RECORD
REMOTE
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 W
LS
07
SS
03
TS
02
DET
OFF
ALARM
OFF
AREA
EDIT
X
EXIT
1)
LS (Level of Sensitivity)
“LS” is to set the sensitivity of comparing two different images. The smaller the
value is, the higher sensitivity for motion detection. The highest sensitivity setting is
00, and the lowest sensitivity setting is 15. The default value is 07.
2)
SS (Spatial Sensitivity)
“SS” is to set the sensitivity for detecting the size of one object (the number of the
grids) on the screen. The smaller the value is, the higher sensitivity for motion
detection.
The highest sensitivity setting is 00, and the lowest sensitivity setting is 15. The
default setting is 03.
22
FREQUENTLY-USED FUNCTIONS
Note: The default setting of SS is 03, which means once an object is detected
more than 3 grids, the system will get triggered. So the value of SS must be
less than the number of grids that you set up for the motion detection area.
3)
TS (Time of Sensitivity)
“TS” is to set the sensitivity regarding how long one object stays in the detection
area and triggers the recording. The smaller the value is, the higher sensitivity for
motion detection.
The highest sensitivity setting is 00, and the lowest sensitivity setting is 15. The
default setting is 02.
4)
DET
Select if you want to activate the motion detection function for the selected channel
(ON/OFF).
5)
ALARM
Select N.C./ N.O depending on your installation need. The default alarm value is
OFF.
6)
AREA
Click “EDIT” to set the motion detection area.
There are 16 × 12 grids per camera for all channels. Pink blocks represent the area
that is not being detected while the transparent blocks are the area under
detection.
5.5 PTZ Camera Setting
Right-click to display the main menu, and select “ADVANCE CONFIG”
“REMOTE”.
ADVANCE CONFIG
CANERA
DETECTION
ALERT
NETWORK
SNTP
DISPLAY
RECORD
REMOTE
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 W
DEVICE
PTZ
ID
00
PROTOCOL
NORMAL
RATE
2400
X
EXIT
1)
DEVICE
For the PTZ camera, select “PTZ”.
2)
ID
Click the current value to set the ID number (0 ~ 255) for the connected PTZ
camera if necessary.
23
FREQUENTLY-USED FUNCTIONS
Make sure the ID setting of the camera is the same as the setting here, or the DVR
will not be able to control the device.
Note: To know the default ID of the PTZ camera, please refer to its user manual.
3)
PROTOCOL
Select NORMAL (our protocol), P-D (PELCO-D) or P-P (PELCO-P) protocol.
4)
RATE
Select the baud rate for the connected PTZ camera (2400 / 4800 / 9600 / 19200 /
57600 / 115200).
Make sure the baud rate setting of the camera is the same as the setting here, or
the DVR will not be able to control the device.
Note: To know the default baud rate of the PTZ camera, please refer to its user
manual.
5.6 System Setting
5.6.1 Password Setting
Right-click to display the main menu, and select “SYSTEM”
“TOOLS”.
SYSTEM
TOOLS
SYSTEM INFO
USB BACKUP
DVD BACKUP
LANGUAGE
ADMIN PASSWORD
OPERATOR PASSWORD
UPGRADE
ENGLISH
SETUP
SETUP
SUBMIT
EXIT
1)
ADMIN PASSWORD
Click “SETUP” to change the administrator password. The default administrator
password is 0000.
When you’re prompted to enter the DVR password, enter the administrator
password, and
are allowed.
2)
will be shown on the status bar of the screen and all operations
OPERATOR PASSWORD
Click “SETUP” to set or change the operator password. .
When you’re prompted to enter the DVR password, enter the operator password,
and
will be shown on the status bar of the screen and the main menu is NOT
allowed to access.
24
FREQUENTLY-USED FUNCTIONS
5.6.2 System Upgrade
Note: DVR system upgrade might cause all HDD data cleared when your current
system version is too old from the latest version. Therefore, before
upgrading the DVR system, check your current firmware version with your
installer or distributor, and make video backup if necessary.
Right-click to display the main menu, and select “SYSTEM”
“TOOLS”
“UPGRADE”.
Save the upgrade files obtained from your installer or distributor in a compatible USB
flash drive, and insert it into the USB port at the front panel.
Then, click “SUBMIT” to start upgrading.
Note: Before using the USB flash drive, please use your PC to format the USB
flash drive to FAT32 format first. For the list of compatible USB flash drives,
please refer to “APPENDIX 2 COMPATIBLE USB FLASH DRIVE LIST” at page
48.
5.6.3 Video Backup
Right-click to display the main menu, and select “SYSTEM”
BACKUP”.
“USB BACKUP” or “DVD
Note: DVD BACKUP is only available for selected models. Please check the
specifications of your DVR model for details.
Insert a compatible USB flash drive to the USB port at the front panel, or press
eject the DVD writer and place a DVD-R or CD-R to it.
to
Note: Before using the USB flash drive, please use your PC to format the USB
flash drive to FAT32 format first. For the list of compatible USB flash drives,
please refer to “APPENDIX 2 COMPATIBLE USB FLASH DRIVE LIST” at page
48.
25
FREQUENTLY-USED FUNCTIONS
SYSTEM
TOOLS
SYSTEM INFO
USB BACKUP
DVD BACKUP
START DATE
START TIME
END DATE
END TIME
CHANNEL
01
05
09
13
HARD DISK
BACKUP
REQUIRE SIZE: 554MB
EXIT
2009/NOV/19
08:30:21
2009/NOV/19
17:59:29
02
03
04
06
07
08
10
11
12
14
15
16
ALL HDD
SUBMIT
SUBMIT
AVAILABLE SIZE: 3788.0MB
1)
START DATE / START TIME
Select the start date & time.
2)
END DATE / TIME
Select the end date & time.
3)
CHANNEL
Click to select the channel(s).
4)
HARD DISK
Select the hard disk containing the video data you need or “ALL HDD”.
5)
BACKUP
Click “SUBMIT” to start backup.
6)
REQUIRE SIZE
To know the size of the expected backup video before backup, click
“SUBMIT” to start calculating.
Backup File Playback
During the backup process, a file player installer “PLAYER.EXE” will also be
copied into your USB flash drive or disk, and you will see the message
“CHECK PLAYER” shown on the screen.
Note: The maximum number of CD-R or DVD-R backup files in the CD or DVD is
41.
Insert your USB flash drive or place the CD or DVD into the DVD-ROM drive
of your PC. Install the file player “PLAYER.EXE”, and double click a backup
file to play it directly in your PC and see if the backup is successful.
Note: The supported PC operating systems are Windows 7, Vista, XP & 2000.
26
FREQUENTLY-USED FUNCTIONS
5.6.4 Clear All HDD Data
Right-click to show the main menu, and select “SYSTEM”
“CLEAR HDD”.
“SYSTEM INFO”
SYSTEM
TOOLS
SYSTEM INFO
USB BACKUP
DVD BACKUP
BAUD RATE
HOST ID
AUTO KEY LOCK
CLEAR HDD
RESET DEFAULT
REMOTE CONTROL ID
2400
000
NEVER
HDD-0
SUBMIT
000
SERIAL TYPE
RS485
VIDEO FORMAT
NTSC
VERSION
1010-1005-1006-1007
EXIT
Select the HDD you want to clear, and click “YES” to confirm or “NO” to cancel.
It’s recommended to clear all data in the hard disk when:
It’s the first time to use this DVR to ensure the recorded data are not mixed with other data
previously saved in the same hard disk.
DVR date and time are changed accidentally when the recording function is activated.
Otherwise, the recorded data will be disordered and you will not be able to find the
recorded file to backup by time search.
5.7 Network
The description below is only for STATIC network type. For PPPOE and DHCP settings,
you need to set from “Video Viewer”.
For details, please download the extended user manual for “Video Viewer” from
http://www.surveillance-download.com/user/CMS.pdf.
STATIC
ADVANCE CONFIG
CANERA
DETECTION
ALERT
NETWORK
SNTP
DISPLAY
RECORD
REMOTE
NETWORK TYPE
IP
GATEWAY
NETMASK
PRIMARY DNS
SECONDARY DNS
PORT
SAVE NETWORK SETTING
STATIC
192.168.001.010
192.168.001.254
255.255.255.000
168.095.001.001
139.175.055.244
0080
APPLY
EXIT
1)
NETWORK TYPE
Select the network type as STATIC and set all the information needed in the DVR.
27
FREQUENTLY-USED FUNCTIONS
3)
NETWORK INFORMATION (IP / GATEWAY / NETMASK)
Key in all the network information obtained from your ISP (Internet Service
Provider).
4)
DNS (PRIMARY DNS / SECONDARY DNS)
Key in the IP address of the domain name server obtained from your ISP (Internet
Service Provider).
5)
PORT
The valid number ranges from 1 to 9999. The default value is 80. Typically, the
TCP port used by HTTP is 80. However in some cases, it is better to change this
port number for added flexibility or security.
6)
SAVE NETWORK SETTING
Click “APPLY” to confirm the settings.
28
REMOTE OPERATION
6. REMOTE OPERATION
You can also control the DVR remotely via the supplied licensed software “Video Viewer”,
Internet Explorer web browser, and Apple’s QuickTime player.
6.1 Supplied Licensed Software
The sections below describe frequently-used functions of the Video Viewer. For details
about this software and network settings, please download its extended user manual
from the following link:
http://www.surveillance-download.com/user/CMS.pdf
6.1.1 Installation & Network Connection
1)
Install the software
Step1: Place the supplied CD into your CD-ROM or DVD-ROM drive. The program
will be automatically run.
Step2: Click “Download The Latest Version” under “Licensed Software AP” to
download the latest version of Video Viewer from the Internet.
Step3: Follow the on-screen instructions to finish the installation. When the
installation is completed, a shortcut icon “
desktop.
2)
” will be placed on your PC
Network Connection
Local Connection (via LAN)
LAN is used when it’s the first time to remotely access the DVR and you
need to configure the network setting of your DVR based on your network
type in advance.
a) Connect the DVR to your PC via a RJ45 network cable. The default DVR values
are as follows:
Item
Default Value
IP address
192.168.1.10
User name
admin
Password
admin
Port
80
b) Set the PC’s IP address as “192.168.1.XXX” (1~255, except 10) in order to
make the PC and DVR under the same domain.
c) Double-click “
” icon on your PC desktop to enter the control panel. By
defaults, the “Address Book” panel will be displayed on the right side of the
29
REMOTE OPERATION
control panel.
d) Click “ ”
“
” to key in the default IP address, user name, password,
and port number of the DVR you intend to connect.
OR
Click “
”
“
” to search the available IP address(es) of other DVR(s)
under the same domain as your PC’s IP address. The found address(es) will be
listed, and can be added into the address book by clicking “
”.
e) Double-click the IP address you just added into the address book to log in.
Remote Connection (via Internet)
When the network configuration of your DVR is completed, you can access your
DVR remotely via Internet.
a) Double-click “
” icon on your PC desktop to enter the control panel. By
defaults, the “Address Book” panel will be displayed on the right side of the
control panel.
b) Click ”
”
”
” to key in the IP address, user name, password, and
port number of the DVR you intend to connect.
OR
Click ”
”
”
” to search the available IP address(es) of other
DVR(s) under the same domain as your PC’s IP address. The found address(es)
will be listed, and can be added into the address book by clicking ”
c) Double-click the IP address you just added into the address book to log in.
30
”.
REMOTE OPERATION
6.1.2 Control Panel Overview
Two control panels are available and can be switched depending on your use
habit.
Simplified Version (Default)
31
REMOTE OPERATION
Full Function Version
Main Button Overview
Button
Simplified
Full
Function
Function
Address Book
Miscellaneous
Control
Description
Click to show the predefined IP address(es). You
can add, remove or search the IP address to log
in the DVR remotely.
Remote
Config
Click to go into the detailed
DVR setting.
Record
Setting
Click to go to the detailed
record setting.
Custom
Setting
Click to choose the language of
this program. The language
change will take effect when
this program is closed and
executed again.
Click to view all event and recording logs, search
the desired log(s) by date, or playback the
recording of the selected log.
Log
32
REMOTE OPERATION
Button
Simplified
Full
Function
/
/
Function
Description
Record /
Record Stop
Click to start / stop the manual recording.
Snapshot
Information
DVR Control
Click to take a snapshot of the current view. The
snapshot will be saved in the path you specified in
“Record Setting”.
Click to show the current network connection
details.
Click to go to the DVR control panel to operate
the DVR remotely.
6.1.3. General Operation
Record
To record remotely at the same time for any event or alarm at the DVR side, click “
or “
” → “
” to go to the “Record Setting” page.
In the “Record Setting” page, you can set the following items:
‧Record type
‧Hard disk overwriting
‧Pre- / post-alarm record time
‧Record time setting
‧Record path
33
”
REMOTE OPERATION
If “Manual” is checked, click “
” or “
” on the main control panel to start the
manual recording immediately, and the recordings will be saved in the specified location.
If “Motion” and / or “Alarm” are checked, the recording function will also be enabled at the
remote side when any event is triggered at the DVR side, and the recordings will be
saved in the specified location.
Playback
To play a recording, click “
” or “
”, and select the “Record” tab or “Backup” tab. A
list of all the recordings will be shown by defaults, and you can also sort out the logs you
want to speed up the search time.
To immediately play a recording, select a log from the list, and click “Play”, or
double-click the selected log.
Network Backup
Click “
” → “
”, or click “
” to go into the “Backup” page as follows, and you
can select a specific time range or event to make a video backup remotely.
The file(s) you backup will be from the currently selected IP address.
34
REMOTE OPERATION
Function
Description
HDD Number / Channel
Specify the hard disk (HDD Number) and channel
number (Channel) within which have the video data you
need.
Download by Time
Specify the time range within which has the video data
you want in the “Start Time” and “End Time” columns.
Download by Event
Select an event log from the event list. This list shows
all logs in the specified DVR from the latest to the
earliest.
‧To quickly find the events you need, check or uncheck
the event type “System” / “Manual” / “Alarm” / “Motion”,
and select the log you want.
‧To view the earlier or later logs that are not shown in
the current page, click “Prev. Page” or “Next Page”.
‧To refresh the event list, click “Reload”.
File Path
Assign the location where the backup files are saved.
Simultaneous Playback
To view the backup images simultaneously when the
download process is in progress, select the checkbox
“Simultaneous Playback”. You will see the backup
images while the images are being downloaded to the
PC or notebook.
To simply backup images without previewing, deselect
the checkbox “Simultaneous Playback”. You will only
see a message box indicating the total time needed, the
current status and the saving location.
Download / Cancel
Click “Download” to start or “Cancel” to discard the
video backup.
35
REMOTE OPERATION
6.1.4. E-Map
Video Viewer is also a Central Management System (CMS) software, which allows
network device control & management for up to 16 devices simultaneously.
Note: Before using this function, make sure Video Viewer is connected to all the
devices (up to 16) you want to monitor.
E-Map is ONLY available when the control panel is switch to the full function version.
How to Add an E-Map Group
STEP1: In the simplified version, click “
version, and click “
” to switch the control panel to the full function
” to enter the E-Map page as follows.
Note: To know where the buttons are, please refer to “Simplified Version (Default)
at page 31, and “Full Function Version” at page 32.
STEP2: Right-click to show the shortcut menu on the top-left panel, and select the
E-Map group you want to add. There are three E-Map groups you can add:
Google E-MAP, Single E-MAP, and Building E-MAP.
36
REMOTE OPERATION
37
REMOTE OPERATION
STEP3: When the E-Map group is created, you will see the tree on the top-left panel,
showing all the devices you’ve added to this group.
Icon
Description
The connected device is camera. When it’s selected, it will become red.
The connected device is DVR. When it’s selected, it will become red.
For any motion or alarm event, it will appear on the screen to catch your
attention.
To know what’s happening quickly, double-click the device icon on the
E-Map to show the live view.
How to Edit / Remove an Existing E-Map Group
For Google E-Map Group
Right-click on the group name to show the shortcut menu list, and select “Edit
E-MAP” or “Remove E-MAP” as needed.
You can also add a single E-Map group (Add Single E-MAP) or Building
E-Map group (Add Building E-MAP) into the existing Google E-Map group.
38
REMOTE OPERATION
For Single E-Map Group
Right-click on the group name to show the shortcut menu list, and select “Edit
E-MAP” or “Remove E-MAP” as needed.
39
REMOTE OPERATION
For Building E-Map Group
Right-click on the group name to show the shortcut menu list, and select “Edit
Building E-MAP” or “Remove E-MAP” as needed.
To edit or remove a certain level of the building E-Map group, right click on the
level name, and select “Edit E-MAP” or “Remove E-MAP” as needed.
40
REMOTE OPERATION
6.2 IE Web Browser
You can view the images or operate your DVR with IE web browser.
Note: The supported PC operation systems are Windows 7, Vista, XP and 2000.
Step 1: Key in the IP address used by your DVR in the URL address box, such as
60.121.46.236, and press Enter. You will be prompted to enter the user name and
password to access the DVR.
If the port number your DVR used is NOT 80, you need to key in the port number
additionally. The format is ipaddress:portnum. For example, for IP address
60.121.46.236 and port No. 888, please key in ”http://60.121.46.236:888” into the
URL address box, and press “Enter”.
Step 2: Enter the user name and password, the same as the ones used for video viewer
login, and click “OK”. You will see a similar screen as the following when the login
information is correct.
NO.
1
Function
Home
Description
Click
Click “
2
Playback
to go to the main page of the DVR.
” to enter the playback panel where you can search or select
the event you want to play and download to your PC simultaneously. For
details, please refer to “6.2.1 Event Playback & Download” at page 43.
3
Config.
Click
to go to the detailed DVR setting.
4
PTZ
Click
to enter the PTZ mode.
41
REMOTE OPERATION
NO.
Function
5
Channel Selection
6
Display Mode
Description
Click one of the number to switch to the channel you want to see in full
screen.
Click to show 4-cut display.
:
Click to display each channel one by one, starting from CH1. When
the last channel is displayed, it will start from CH1 again.
To exit from this display mode, press any other channel display
button.
:
Selection
Click
or
Snapshot
Click
to take a snapshot of the current view, and save it to the
to go to the previous / next channel, or change setting.
specified path in your PC set in “
”
“General”.
7
Web Transmission
H.264 / QuickTime
QuickTime is Apple Inc.’s multimedia software. You need to have
QuickTime installed in you operation system first. When “QuickTime” is
selected, you will be promoted to enter the user name and password to
access the server of the DVR.
8
Change Quality
BEST / HIGH / NORMAL / BASIC
Click to change the image quality.
9
Change Resolution
4 CIF / CIF
Click to change the image resolution (4CIF: 704*480 / CIF: 352*240)
Select the audio channel you want for listening to the live audio.
10
Audio Channel Selection
Note: Your camera must support audio recording, and connect
to the video channel which supports audio recording and
the audio input of the DVR. For details, please refer to
“1.3 Rear Panel” at page 3.
means mute.
To disable the mute status, click this icon again and select the audio
channel you want.
42
REMOTE OPERATION
6.2.1 Event Playback & Download
/
Previous /
Next Hour
Click to jump to the next / previous time interval in an hour, for example, 11:00
~ 12:00 or 14:00 ~ 15:00, and start playing the earliest event video clip
recorded during this whole hour.
Fast
Forward
Increase the speed for fast forward. Click once to get 4X speed forward and
click twice to get 8X speed, etc., and the maximum speed is 32X.
Fast Rewind
Increase the speed for fast rewind. Click once to get 4X speed rewind and
click twice to get 8X speed, etc., and the maximum speed is 32X.
Play
Click to play the current video clip.
Pause
Click to pause the video playback.
Stop
Click to stop the video playback.
Step
In the pause mode, click to get one frame forward.
Click to mute the playback if necessary, and click again to restore.
Audio
Snapshot
Note: Audio is available when your camera supports audio
recording, and connects to the video channel which supports
audio recording and the audio input of the DVR. For details,
please refer to “1.3 Rear Panel” at page 3.
Click to take a snapshot of the current view, and save it to the specified path
in your PC set in “
Download
”
“General”.
Click to download the current video clip to the specified path in your PC.
43
APPENDIX 1 SPECIFICATIONS
Key Lock (Password Protection)
YES
Local User Level
Administrator & Operator
Video Loss Detection
YES
Camera Title
Supports up to 6 letters
Video Adjustable
Hue / Saturation / Contrast / Brightness
Date Display Format
YY/MM/DD, DD/MM/YY & MM/DD/YY
Daylight Saving
YES
Power Source (±10%)
DC 19V
Power Consumption (±10%)
< 64 W
Operating Temperature
10℃ ~ 40℃ (50℉~104℉)
Dimensions (mm)**
432(W) × 90(H) × 326(D)
System Recovery
System auto recovery after power failure
Optional Peripherals
Keyboard controller
* The specifications are subject to change without notice.
** Dimensional Tolerance: ±5mm
45
APPENDIX 1 SPECIFICATIONS
For 4CH Model
Video System
NTSC / PAL (auto detection)
Video Compression Format
H.264
Video Input
4 channels
(composite video signal 1 Vp-p 75Ω BNC)
Video Output (BNC)
Main Monitor: For stable display
Audio Input / Output
4 audio inputs, 1 audio output (Mono)
Maximum Recording Rate
Frame
Maximum Recording Rate
Field
Maximum Recording Rate
CIF
704×480 pixels with 30 IPS <NTSC> / 704×576 with 25 IPS <PAL>
704×240 pixels with 60 IPS <NTSC> / 704×288 pixels with 50 IPS <PAL>
352×240 pixels with 120 IPS <NTSC> / 352×288 pixels with100 IPS <PAL>
Image Quality Setting
Hard Disk Storage
SUPER BEST / BEST / HIGH /NORMAL
Accommodates 1 SATA HDD (capacity up to 2TB)
Quick Search
Time / Motion / Alarm search mode
SATA Interface
Built-in
VGA Interface
Built-in
Recording Mode
Manual / Timer / Motion / Alarm / Remote
Multiplex Operation
Live display / record / playback / backup / network operations
USB Mouse Control
YES
Motion Detection Area
Motion Detection Sensitivity
16 × 12 grids per camera for all channels
3 adjustable parameters for accurate detection
Pre-alarm Recording
YES
Backup Device
USB 2.0 flash drive / Network
Web Transmitting Compression Format
H.264
Ethernet
10/100 Base-T. Supports remote control and live view via Ethernet
Web Interface
Supports licensed software “Video Viewer” / Internet Explorer,
Mozilla Firefox & Google Chrome web browsers / QuickTime player
(5 users access simultaneously)
*Operating System: Windows 7 / Vista / XP / 2000
Network Protocol
TCP/IP, PPPOE, DHCP and DDNS
Fully Remote Independent Operation
YES
Event Notification
By FTP / E-Mail
IR Remote Control
YES (IR receiver built-in)
Mobile Surveillance
YES (including iPhone, BlackBerry, WinCE, J2ME & Android)
Picture Zoom
2X digital zoom
PTZ Control
YES
Alarm I/O
4 inputs, 1 output
Key Lock (Password Protection)
YES
Local User Level
Administrator & Operator
Video Loss Detection
YES
Camera Title
Supports up to 6 letters
Video Adjustable
Hue / Saturation / Contrast / Brightness
46
APPENDIX 1 SPECIFICATIONS
Date Display Format
YY/MM/DD, DD/MM/YY & MM/DD/YY
Daylight Saving
YES
Power Source (±10%)
DC 19V
Power Consumption (±10%)
< 42 W
Operating Temperature
10℃ ~ 40℃ (50℉~104℉)
Dimensions (mm)**
343(W) × 59(H) × 223(D)
System Recovery
System auto recovery after power failure
Optional Peripherals
Keyboard controller
* The specifications are subject to change without notice.
** Dimensional Tolerance: ±5mm
47
APPENDIX 2 COMPATIBLE USB FLASH DRIVE LIST
APPENDIX 2 COMPATIBLE USB FLASH DRIVE LIST
Please upgrade the firmware of the DVR to the latest version to ensure the accuracy of the
following table. If the USB flash drive is not supported by the DVR, the “USB ERROR”
message will be shown on the screen.
Note: Please use your PC to format the USB flash drive as “FAT32”.
Note: You can backup up to 2GB video data for one-time USB backup. To backup
more data, please set the time & channel(s) you want, and start USB
backup again.
MANUFACTURER
MODEL
CAPACITY
Transcend
JFV35
4G
JFV30
8G
Kingston
DataTraveler
1G
PQI
U172P
4G
Apacer
AH320
2GB
AH320A
8GB
AH220
1GB
AH320
4GB
A-data
RB-18
1GB
Sandisk
Cruzer Micro
2G
Cruzer Micro
4G
Cruzer4-pk
2G
Netac
U208
1G
MSI
F200
4G
SONY
Micro Vault Tiny 2G
2G
Micro Vault Tiny 4G
4G
Micro Vault Tiny
1G
48
APPENDIX 3 COMPATIBLE SATA HDD LIST
APPENDIX 3 COMPATIBLE SATA HDD LIST
Please upgrade the firmware of the DVR to the latest version to ensure the accuracy of the
following table.
MANUFACTURER
MODEL
Seagate
WD
Maxtor
HITACHI
CAPACITY
ROTATION
ST3320613AS
320GB
7200 rpm
ST33500320AS
500GB
7200 rpm
ST3750330AS
750GB
7200 rpm
ST31000340AS
1000GB
7200 rpm
WD3200AAKS
320GB
7200 rpm
WD5000AACS
500GB
7200 rpm
WD6400AAKS
640GB
7200 rpm
WD7500AAKS
750GB
7200 rpm
WD10EADS
1TB
7200 rpm
WD15EADS
1.5TB
7200 rpm
WD20EADS
2TB
7200 rpm
STM3500320AS
500GB
7200 rpm
STM3750330AS
750GB
7200 rpm
HDT725032VLA360
320GB
7200 rpm
HDS721010KLA330
1000GB
7200 rpm
49
APPENDIX 4 MAIN MENU STRUCTURE
APPENDIX 4 MAIN MENU STRUCTURE
QUICK START
GENERAL
CHANNEL TITLE
EVENT STATUS
DATE DISPLAY
IMAGE SIZE
QUALITY
IMAGE PER SECOND
TIME SETUP
DATE
TIME
DATE SETUP
DATE INFO
DISPLAY DATE OF MODE
FORMAT
DAYLIGHT
DAYLIGHT SAVING
SYSTEM
TOOLS
LANGUAGE
ADMIN PASSWORD
OPERATOR PASSWORD
UPGRADE
SYSTEM INFO
BAUD RATE
HOST ID
AUTO KEY LOCK
CLEAR HDD
RESET DEFAULT
REMOTE CONTROL ID
SERIAL TYPE
VIDEO FORMAT
VERSION
USB BACKUP
DVD BACKUP
(For Selected Models Only)
EVENT INFORMATION
QUICK SEARCH
EVENT SEARCH
HDD INFO
EVENT LOG
ADVANCE CONFIG
CAMERA
BRIGHTNESS
CONTRAST
SATURATION
HUE
COV.
REC
CHANNEL TITLE
DETECTION
LS
SS
TS
DET
ALARM
AREA
ALERT
EXT. ALERT
INT. BUZZER
KEY BUZZER
VLOSS BUZZER
MOTION BUZZER
ALARM BUZZER
HDD BUZZER
ALARM DURATION (SEC)
HDD NEARLY FULL (GB)
NETWORK
SNTP
GMT
NTP SERVER
SYNC PERIOD
DISPLAY
DE-INTERLACE (For Selected Models Only)
SCREEN DWELL DURATION
VGA OUTPUT
DISPLAY COVERT
HDD DISPLAY MODE
50
APPENDIX 4 MAIN MENU STRUCTURE
ADVANCE CONFIG
DISPLAY
DISPLAY OUTPUT PATH
ALPHA BLENDING
RECORD
MANUAL RECORD ENABLE
EVENT RECORD ENABLE
TIMER RECORD ENABLE
EVENT RECORD IPS
TIMER RECORD IPS
PRE-ALARM RECORD
OVERWRITE
EVENT RECORD ALL CHANNEL
KEEP DATA LIMIT (DAYS)
REMOTE
SCHEDULE SETTING
RECORD
DETECTION
51
APPENDIX 5 DVR BATTERY REPLACEMENT
APPENDIX 5 DVR BATTERY REPLACEMENT
DVR time reset after power failure, for example, caused by a power outage, will cause the
disorder of the recorded data, and users may have problems in searching the event clip they
want. To keep the DVR time from resetting, a non-chargeable lithium battery, CR2032, is
installed in the DVR.
However, the DVR time might still get reset when the DVR battery is low or even running out of
power. If so, please replace the DVR battery, CR2032, right away as instructed below.
How to replace CR2032
Note: The lithium battery, CR2032, is a non-chargeable battery, and should be
purchased separately. Please replace only with the same or equivalent type
battery in case of danger.
Step1: Stop all DVR recording immediately to prevent the disorder of the recorded data.
Then, back up the recorded data if necessary.
Step2: Power off the DVR, and disconnect the DVR power.
Step3: Remove the DVR cover, and find the battery on the mainboard.
Step4: Push the release as indicated below to remove the battery.
Step5: Get a new battery with the side of “CR2032” facing up, and install it to the mainboard.
Step6: Replace the DVR cover and connect to power.
Step7: Set DVR date & time, and resume recording. For details, please refer to “2.4 Date and
Time Setting” at page 10, and “5.2 Record” at page 19.
52
APPENDIX 6 PIN CONFIGURATION
APPENDIX 6 PIN CONFIGURATION
‧ For 16CH Model
Siren:
When the DVR is triggered by alarm or motion, the
COM connects with NO and the siren with strobe
starts wailing and flashing.
Magnetic Contact:
When the magnetic contact is opened, the alarm
will be triggered and the recording is on.
* The D-Sub connector shown above is optional.
PIN
1
FUNCTION
GND
DESCRIPTION
GROUND
Connect ALARM INPUT (PIN 2 -- 9) and GND (PIN 1) connector with wires. Once
an alarm is triggered, the DVR will start recording and the buzzer will be on.
2~9
ALARM INPUT
*
PIN
PIN 2
PIN 3
PIN 4
PIN 5
PIN 6
PIN 7
PIN 8
PIN 9
Alarm
1
3
5
7
9
11
13
15
Corresponding video channel
CH1
CH3
CH5
CH7
CH9
CH11
CH13
CH15
10~11
PIN OFF
12
RS485-A
13
EXTERNAL ALARM NO
Under the normal operation, COM disconnects with NO. But when any alarm is
triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
14
PIN OFF
NA
15~22
ALARM INPUT
Connect ALARM INPUT (PIN 15 – 22) and GND (PIN 1) connector with wires.
Once an alarm is triggered, the DVR will start recording and the buzzer will be on.
PIN
Alarm
Corresponding video channel
PIN 15
2
CH2
PIN 16
4
CH4
PIN 17
6
CH6
PIN 18
8
CH8
PIN 19
10
CH10
PIN 20
12
CH12
PIN 21
14
CH14
PIN 22
16
CH16
23~23
PIN OFF
24
RS485-B
25
EXTERNAL ALARM
COM
NA
*
NA
Under the normal operation, COM disconnects with NO. But when any alarm is
triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
53
APPENDIX 6 PIN CONFIGURATION
For 8CH Model
Siren:
When the DVR is triggered by alarm or motion, the
COM connects with NO and the siren with strobe
starts wailing and flashing.
Magnetic Contact:
When the magnetic contact is opened, the alarm
will be triggered and the recording is on.
* The D-Sub connector shown above is optional.
PIN
1
FUNCTION
GND
DESCRIPTION
GROUND
Connect ALARM INPUT (PIN 2 – 5) and GND (PIN 1) connector with
wires. Once an alarm is triggered, the DVR will start recording and the
buzzer will be on.
2~5
PIN
PIN 2
PIN 3
PIN 4
PIN 5
ALARM INPUT
Alarm
1
3
5
7
Corresponding video channel
CH1
CH3
CH5
CH7
*
6 ~ 11
PIN OFF
12
RS485-A
13
EXTERNAL ALARM NO.
Under the normal operation, COM disconnects with NO. But when any
alarm is triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
14
PIN OFF
NA
NA
Connect ALARM INPUT (PIN 15 – 18) and GND (PIN 1) connector with
wires. Once an alarm is triggered, the DVR will start recording and the
buzzer will be on.
15~18
PIN
PIN 15
PIN 16
PIN 17
PIN 18
ALARM INPUT
Alarm
2
4
6
8
Corresponding video channel
CH2
CH4
CH6
CH8
*
19~23
PIN OFF
24
RS485-B
25
EXTERNAL ALARM
COM
NA
Under the normal operation, COM disconnects with NO. But when any
alarm is triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
54
APPENDIX 6 PIN CONFIGURATION
‧ For 4CH Model
Siren:
When the DVR is triggered by alarm or motion, the
COM connects with NO and the siren with strobe
starts wailing and flashing.
Magnetic Contact:
When the magnetic contact is opened, the alarm
will be triggered and the recording is on.
* The D-Sub connector shown above is optional.
PIN
FUNCTION
DESCRIPTION
Connect ALARM INPUT (PIN1 – 4) and GND (PIN5) connector with wires.
Once an alarm is triggered, the DVR will start recording and the buzzer
will be on.
1~4
PIN
PIN 1
PIN 2
PIN 3
PIN 4
ALARM INPUT
Alarm
1
2
3
4
Corresponding video channel
CH1
CH2
CH3
CH4
*
5
6
7
GND
GROUND
EXTERNAL ALARM
Under the normal operation, COM disconnects with NO. But when any
alarm is triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
COM
EXTERNAL ALARM
NO
8
RS485-A
9
RS485-B
10~11
GND
Under the normal operation, COM disconnects with NO. But when any
alarm is triggered, COM connects with NO.
Attention: The voltage restriction is under DC24V 1A.
GROUND
55
APPENDIX 7 DVD WRITER INSTALLATION
APPENDIX 7 DVD WRITER INSTALLATION
Some DVR models allow users to install a DVD writer by themselves. To know whether your
DVR supports this feature, please check with your local distributor or retailer.
The supported DVD writer models are as follows. Please use only the suggested DVD writer
models to ensure the compatibility.
Type
SATA
Brand
Liteon
Model
iHAS120
SONY
AD-7240S
Note: Before installing the DVD writer, make sure your DVR is powered off and
your DVR supports this feature.
Step1: Remove the DVR cover, and find the DVD writer bracket to remove it.
Step2: Put the DVD writer in the bracket, and fix it to the bracket with two screws (optional) on
each side.
Step3: Connect the data bus and power cables* to the SATA DVD writer.
*Data bus & power cables are optional.
Step4: Connect the data bus and power cables to the data bus and power jack on the DVR
main board.
Note: Make sure the power cable of the DVD writer is plugged into the black jack
on the DVR main board. This power jack can supply power to one hard disk
and one DVD writer simultaneously. The white jack is used to supply power
to only one hard disk.
Step5: Replace the bracket to the DVR base and fix it.
56