MSI-PM1033
HMC86508
Flat Panel Control Module
The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
Contents
1. Introduction....................................................................... 2
1.1 Specifications ..............................................................3
2. Installation ........................................................................ 4
2.1 PM-1033's Layout .......................................................6
2.2 Unpacking Precautions… … … … …
2.3 JUMPER SETTING .....................................................8
2.4 PM-1033'S CONNECTOR.........................................10
PM-1033
1
Introduction
Welcome to the PM-1033 HM86508 Flat Panel Control Module.
The PM-1033 is a PC/104 form factor module. It uses HM86508
LCD/CRT Controller Chips to support high resolution LCD/CRT display panel. It is made for the SBCs that are not equipped with
LCD/CRT interface from the factory and is the best solution for internal flat panel connection.
PM-1033
1.1 Specifications :
PC/104 form factor
LCD/CRT Interface : HM86508 Chipset with 1MB RAM display memory
Resolution: up to 1024 x 768, 256 colors for CRT
800 x 600, 16M colors for LCD
Output +/-40V VEE for flat panel need
LCD Type : TFT or DSTN (selectable from JP5)
Support 18/24-bit data signals
Simultaneous VGA and LCD display
Flash Disk: support M-Systems Disk On Chip
Operating Temperature: 0-60 o
C
Support LCD Type :
Prime View P64CV1 640 x 480 TFT 6.4” (BIOS 5081.HMC)
Toshiba LTM10C209A 640 x 480 TFT 10.4” (BIOS 5081.HMC)
Toshiba LTM10C273A 800 x 600 TFT 10.4” (BIOS 5082.HMC)
Toshiba LTM12C275A 800 x 600 TFT 12.1” (BIOS 5082.HMC)
NEC NL8060AC33-13 640 x 480 TFT 10.4” (BIOS 5081.HMC)
NEC NL8060AC26-04 800 x 600 TFT 10.4” (BIOS 5082.HMC)
NEC NL8060BC31-09 800 x 600 TFT 12.1” (BIOS 5082.HMC)
Hitachi LMG9211XUCC 640 x 480 DSTN 9.4”(BIOS 5081/2.HMC)
Chunghwa CLX-8102S-C3X 640 x 480 DSTN 9.4” (BIOS 5081/2.HMC)
Kyocera KCB104VG2BA-A01640X480 DSTN 10.4”(BIOS 5081/2.HMC)
PM-1033
2
Installation
This chapter describes how to install the PM-1033. The layout of
PM-1033 is shown on the next page and the Unpacking
Precautions that you should be careful with are described on the following page. Also included is the jumpers and connectors description for this PM-1033.
Hardware Installation :
1. Please read the Unpacking Precautions first before you install the PM-1033 (see page 6).
2. If your LCD panel is TFT type then skip JP7 and JP8
(default setting of JP8 is for TFT type LCD panel)
3. If your LCD panel is MONO or DSTN type, JP7 must be set according to the data sheet of the LCD panel (+VEE or –
VEE) then adjust the output of VEE through R19 (Variable
Resistor). Caution: don’ t make connection to your LCD panel while you adjust the output of VEE, it may damage your LCD panel. Measure the voltage with a voltage meter.
4. Caution: Don’ t set the JP8 to VEE if your LCD panel is
TFT type. It will cause fatal damage to your LCD panel.
5. Select the correct BIOS type for your LCD panel on JP5.
6. Connect your LCD panel cable to CN16 and CRT monitor to
CN15.
PM-1033
Software (driver) Installation :
If this is the first time you install Windows, please plug the
PM-1033 into the PC/104 (in POWER OFF condition) then start to install the Windows. After the installation complete, press the button > Settings > Control
Panel. Select the Display Icon and then press Settings
Menu and press the Advanced button. Press Adapter
Menu and then press the Change button. Windows will go into Update Device Driver Wizard, press Next button and then check on: Display a list of all the drivers in a specific
location, so you can select the driver you want. Then press Have Disk button and browse or select the correct driver from the diskette. Choose the HM86508 driver from the disk under the NT40, WIN31 or WIN95 directory, depending on the Windows version that you install.
For hard disk, which has been installed by another VGA driver before, to update the driver: under Control Panel, select System icon then press Device Manager Menu.
Remove the old display adapters and then install the new driver using Add New Hardware wizard under the Control
Panel. Consult the Microsoft Windows User Manual for the driver installation.
PM-1033
2.1 PM-1033's Layout
PM-1033
2.2 Unpacking Precautions
PM-1033. You can do it by using a grounded wrist strap at all times or by frequently touching any conducting materials that is connected to the ground.
ü Disconnect power supply before handling and doing connection on PM-1033. Do not plug any connector or jumper while the power is on. It will cause fatal damage to your LCD panel.
ü Make sure that every connector is connected in correct direction.
Any incorrect connection may cause smoke or burn of electrical parts or fatal damage of your LCD panel.
ü Some components on PM-1033 are very sensitive to static electric charges and can be damaged by a sudden rush of power.
Ground yourself to remove any static charge before touching your
PM-1033
2.3 JUMPER SETTING
•
JP1 JP2 JP3 JP4: Disk On Chip Memory Address
FUNCTION JP1 JP2 JP3
CE000H
D6000H
DE000H
1-2
1-2
1-2
2-3
2-3
2-3
2-3
2-3
2-3
JP4
3-4
5-6
7-8
•
JP5 : SELECT FLASHROM SEGMENT
The Flash ROM used on PM-1033 is 64K Flash ROM. It is divided into two segment, 32K each, BIOS 1 and BIOS 2.
JP5 DESCRIPTION
1-2 BIOS 1
2-3 BIOS 2
Note: PM-1033 is equipped with one BIOS diskette which contains the following files:
File Name BIOS 1 BIOS 2
5081.HMC 640 x 480 TFT 640 x 480 DSTN
5082.HMC 800 x 600 TFT 640 x 480 DSTN
PM-1033 is initially installed with 5081.HMC. The BIOS can be programmed or updated with the other *.HMC files by using an
EPROM programmer.
•
JP7 : VEE SELECTION (for LCD type DSTN/MONO)
FUNCTION JP7
+VEE
-VEE
1-2
2-3
+VEE = +5V ~ +40V
-VEE = -0V ~ -40V
User must read the specification of the LCD panel to know the polarity and bias voltage of the LCD panel. The bias voltage can be set from R19.
PM-1033
•
JP8 : CN16 Pin7 VEE or FPVEE SELECTION
FUNCTION JP8
VEE
FPVEE
1-2
2-3
FPVEE = LCD control signal
VEE = +/- 40V output (adjustable through R19) for MONO or
DSTN type of LCD panel.
Caution: don’ t set JP8 to VEE for TFT type of LCD panel, it will cause fatal damage!
PM-1033
2.4 PM-1033’S CONNECTOR
•
CN4: PC104-64 pin Connector
•
CN3: PC104-40 pin Connector
•
CN16 : 22x2 header/2.0mm LCD Connector
PIN NO FUNCTION PIN NO FUNCTION
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
+12V
+12V
GND
GND
+5V
+5V
FPVEE/VEE
GND
P0
P1
P2
P3
P4
P5
P6
P7
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
P14
P15
P16
P17
P18
P19
P20
P21
P22
P23
GND
GND
SHFCLK
FLM
M
LP
17
18
19
20
P8
P9
P10
P11
39
40
41
42
GND
ENBKL
GND
N/C
21
22
P12
P13
43
44
+5V
N/C
Note: * pin 7 of CN16 can be set as FPVEE or VEE from JP8
* the range of VEE is +5V ~ +40V and 0V ~ -40V, tunable from R19
PM-1033
•
CN15: 5X2 header/2.54mm CRT Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
2
3
4
5
RED
GREEN
BLUE
HS
VS
6
7
8
9
10
NC
NC
GND
GND
GND
PM-1033
