Instruction Manual

I CRAFTSMAN°I

12 Amp Motor

265 / 346

km/h

ELECTRIC BLOWER/VACUUM

Model No.

C944.511710

• Safety

• Assembly

• Operation

• Maintenance

• Fran£ais

FOR HOUSEHOLD USE ONLY C _..._US

WARNING:

Read and follow all Safety Rules and Operating

Instructions before first use of this product.

For answers to your questions about this product, call 7am-7pm, Mon.-Sat., or 10am-7pm, Sun.

1-800-235-5878

(Hours listed are Central Time)

530086292

Sears Canada, Inc., Toronto, Ontario M5B 2B8

3/31/04

Warranty Statement

Safety Rules

Assembly

Operation

Maintenance

Service & Adjustments

5

8

10

10

2

2

Parts Available

Storage

Troubleshooting

French

Parts Ordering

Table

11

11

11

12

Back Cover

TWO (2) YEAR WARRANTY FOR CRAFTSMAN ® ELECTRIC POWER BLOWER

For two (2) years from date of purchase, Sears Canada, Inc., will repair or replace free of charge at Sears' option parts which are defective as a result of materials or workmanship.

COMMERCIAL OR RENTAL USE:

Warranty is void if the Electric Power Blower is used for Commercial or Rental purposes.

This warranty does NOT cover:

Expendable parts such as blower tubes which may become broken.

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE ELECTRIC POWER BLOW-

ER TO THE NEAREST SEARS SERVICE CENTRE/DEPARTMENT IN CANADA. THIS

WARRANTY APPLIES ONLY WHILE THIS PRODUCT IS IN USE IN CANADA.

This warranty is in addition to any statutory warranty and does not exclude or limit legal rights you may have, but shall run concurrently with applicable provincial legislation.

Furthermore, some provinces do NOT allow limitation on how long an implied warranty will last, so the above limitations may not apply to you.

Sears Canada, Inc,, Toronto, Ontario M5B 2B8

IMPORTANT WARNINGS AND

SAFETY INSTRUCTIONS

AWARNING:

When using electric gardening appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and serious injury. The warnings and safety instructions in this manual must be followed to reduce the risk of fire, electric shock, or injury, and to provide reasonable safety and efficiency in using this unit.

The operator is responsible for following the warnings and instructions in this manual and on the unit.

Read the entire instruction manual before assembling and using the unit!

Restrict the use of this unit to persons who read, understand, and follow the warnings and instructions in this manual and on the unit. Never allow children to use this unit. Close attention is necessary when used near children.

OPERATOR SAFETY

• Always wear safety glasses or similar eye protection when operating, servicing, or performing maintenance on your unit. Wearing eye protection can help to prevent rocks or debris from being blown or ricocheting into eyes and face which can result in blindness or serious injury.

• Always wear a respirator or facemask when working with the unit in dusty environments.

• Dress safely cation.

in long pants.

Do not go barefoot or wear short pants or sandals.

• Do not operate the unit when you are tired, ill, upset, or if you are under the influence of alcohol, drugs, or medi-

away parts.

hairsoitisabove length.

fingers,

Hair, clothing ties, jewelry, withloosely tassels, moving etc., parts.

_IkWARNING: environment.

Avoid a dangerous

To reduce the risk of electrical shock, do not use in rain, in damp or wet locations, or around swimming pools, hot tubs, etc.

Do not

expose to snow, rain, or water to avoid the possibility of electrical shock.

Do not handle extension cord plug or unit with wet hands.

• Use only a voltage supply as shown on the nameplate of the unit.

• Avoid dangerous situations.

Do not use in presence of flammable liquids or gases to avoid creating a fire or explosion and/or causing damage to unit.

• Avoid dangerous environments.

Do not use in unventilated areas or where dust or explosive vapors can build up.

• To reduce the risk of electrical shock, use extension cords specifically marked as suitable for outdoor appliances.

The electrical rating of the cord must not be less than the rating of the unit. The cord must be marked with the suffix '_4V". Make sure your extension cord is in good condition.

Inspect extension cord before use and replace if damaged.

An undersized extension cord will cause a drop in line voltage resulting in loss of power and overheating.

If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord. (NOTE: The correct size to be used depending on the cord length is shown in this manual.

See SELECT AN EXTENSION

CORD in the ASSEMBLY section).

• Inspect the insulation and connectors on the unit and extension cord before each use.

If there is any damage, do not use until damage is repaired by your Sears Service Centre. Do not pull or carry by cord; do not use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.

Keep cord away from heated surfaces.

Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Tie cord to cord retainer and connect to recessed plug as shown in this manual to prevent damage to unit and/or extension cord and to reduce the possibility of the extension cord disconnecting from the unit during operation.

• Do not use the unit if the switch does not turn the unit on and off properly.

Have the unit repaired by your Sears

Service Centre.

• Keep the extension cord clear of operator and obstacles at all times.

Do not expose cords to heat, oil, water, or sharp edges.

• Avoid any body contact with any grounded conductor, such as metal fences, or pipes, to avoid the possibility of electric shock. Don't handle plug or unit with wet hands.

• Do not use with damaged cord or plug. If unit is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to your Sears Service

Centre for repair.

• Ground Fault Circuit Interrupter (GFCl) protection should be provided on the circuit or outlet to be used for this unit.

Receptacles are available having builtin GFCl protection and may be used for this measure of safety.

• Keep others including children, animals, bystanders, and helpers a minimum of 30 feet (10 meters) away.

Stop the motor immediately if you are approached.

Do not allow the unit to be used as a toy.

DOUBLE INSULATION

CONSTRUCTION

This unit is double insulated to help protect against electric shock.

Double insulation construction consists of two separate "layers" of electrical insulation instead of grounding.

Tools and appliances built with a double insulation system are not intended to be grounded.

No grounding means is provided on this unit, nor should a means of grounding be add-

ed to this unit. As a result, the exten- sion cord used with your unit can be plugged into any standard 120 volt electrical outlet.

Safety precautions must be observed when operating any electrical tool. The double insulation system only provides added protection against injury resulting from an internal electrical insulation failure.

3

,_WARNING: All electrical repairs to this unit, including housing, switch, motor, etc., must be diagnosed and repaired by qualified service personnel.

Replacement parts for a double insu-

appliance parts appliance

"double ismarked lated".

insulation"

Thesymbol square) appliance.

paired tohave cause service thedouble tiontobecome insulation serious ineffective injury.

UNIT/MAINTENANCE SAFETY

• Turn off all controls and allow the motor to stop before disconnecting the unit from the power source.

• Disconnect the unit from the power source when not in use.

Do not leave the unit when it is plugged into outlet.

• Do not set the unit on any surface except a clean, hard area while the unit is running.

Debris such as gravel, sand, dust, grass, etc., could be picked up by the air intake and thrown out through the discharge opening, damaging the unit, property, or causing serious injury to bystanders or ope rato r.

• Do not overreach or use from unstable surfaces such as ladders, trees, steep slopes, rooftops, etc.

Use extra care when cleaning on stairways.

Keep firm footing and balance at all times.

Keep hands out of tubes.

• Inspect the entire unit before each use for worn, loose, missing, or damaged parts.

Do not use until the unit is in proper working order.

• Disconnect unit from power source before servicing, cleaning, performing maintenance, or storing.

• This unit is double insulated.

See the

DOUBLE INSULATION section.

Have all internal service performed by qualified service repair personnel to avoid creating a hazard or voiding your warranty.

• Have all maintenance other than the recommended procedures described in the instruction manual performed by your Sears Service Centre.

• Always see your Sears Service

Centre to replace a damaged impeller. Parts that are chipped, cracked, broken, or damaged in any other way can fly apart and cause serious injury.

Replace damaged parts before using the unit.

• Never place any object in the air intake opening as this could restrict proper air flow and cause damage to the unit.

• Never douse the unit with water or other liquids or squirt with a water hose. Clean the unit using a damp cloth. Wipe off with a clean dry cloth.

See MAINTENANCE.

• Check air intake openings and tubes frequently, always with the unit stopped and power source disconnected.

Keep vents and tubes free of debris which can accumulate and restrict proper air flow.

• Do not burn, incinerate, or expose this unit to extreme heat.

• Store the unit unplugged in a high, cool, dry, indoor area out of the reach of children.

• Use only recommended attachments and replacement parts to avoid creating a hazard and/or voiding warranty.

• Maintain the unit according to recommended procedures.

• Use only for jobs explained in the OP-

ERATION section of this manual.

BLOWER SAFETY

• Use only in daylight or in good artificial light.

• Inspect the area before using the unit.

Remove all debris and hard objects such as rocks, glass, wire, etc., that can ricochet, be thrown, or otherwise cause injury or damage during operation.

• Avoid accidental starting.

Be sure the switch is in the OFF position and keep your hand and fingers away from the switch while connecting the unit to the power source or when carrying a unit connected to the power source.

• Never run the unit without the proper equipment attached.

When used as a blower, always install a blower tube.

Use only recommended attachments.

Do not use with any opening blocked,

Keep free of dust, lint, hair and anything that may reduce air flow.

• To avoid spreading fire, do not use blower near leaf or brush fires, fireplaces, barbecue pits, ashtrays, etc.

• Never place objects inside the blower tubes; always direct the blowing debris away from people, animals, glass, and solid objects such as trees, automobiles, walls, etc. The force of air can cause rocks, dirt, or sticks to be thrown or to ricochet which can hurt people or animals, break glass, or cause other damage.

• Never use for spreading chemicals, fertilizers, or any other substances which may contain toxic materials.

VACUUM

• Stop power inlet before doororattempting must blades tubes.

andtheimpeller nolonger objects toavoid therotating canbethrown thecollection through bagorthehousing missiles and which serious tororothers.

using theunitisdesigned such twigs, topickupdrymagrass, andbitsofpaper.

gravel,

Donotvacutoavoid broken severe to thepossibility donotattempt of tovacuumwater

• Never equipment attached.

vacuum, install andcollection surethecollection completely bagassembly zipped flying when mended

Useonlyrecomattachments.

situations collection discarded orashfrom brush fireplaces, piles, etc.Toavoid

fire,donotuseblower fires, spreading nearleafor fireplaces, ashtrays,

• Always etc.

derstrap vacuuming lossofcontrol.

airintake andvacuum frequently, withtheunitstopped source andthepower disconnected.

freeofdebris proper vents canaccuairflow.

notusewithanyopening freeofdust, blocked, lint,hairandanythatmayreduce

STANDARDS islisted

Laboratories,

ULStandard

Ifsituations occur inthismanual, ment.Ifyouneed

yourSears Centre

1-800-235-5878.

tofollow canresult

SAVE THESE INSTRUCTIONS

CARTON CONTENTS

Model C944.511710

• Blower

• Blower Tube

• 2 Vacuum Tubes

• Elbow Tube

• Collection Bag

Examine parts for damage.

Do not use damaged parts.

NOTE: If you need assistance or find parts missing or damaged, call

1-800-235-5878.

_WARNING" Stop the unit and disconnect from the power source before opening the inlet cover or attempting to insert or remove the inlet restrictor, blower tube, or vacuum tubes. The motor must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades.

_WARNIN_I: If received assembled, ensure your unit is properly assembled and all fasteners are secure.

• A standard screwdriver is required for assembly.

BLOWER ASSEMBLY

NOTE: Assembly instructions for using your unit as a vacuum follow this section.

Attaching the blower tube

If you have already assembled your unit for use as a vacuum, refer to the section HOW TO CONVERT UNIT FROM

VACUUM USE TO BLOWER USE.

To attach blower tube:

1. Align the grooves on the blower tube with the grooves on the blower outlet.

2. Push the blower tube onto the blower outlet until it snaps into place

(tube is secured by red tube release button).

ontube.

theblower button

(_f,,_Tube Release Button

.__)___e r Tube

VACUUM ASSEMBLY

NOTE: Assembly instructions for using your unit as a blower are explained in the previous section.

If you have already assembled your unit for use as a blower, remove the blower tube.

Remove the inlet restrictor

An inlet restrictor is used when using your unit as a blower. This restrictor is not used during vacuum use and must be removed during assembly for vacuum use.

NOTE: Be sure to keep the inlet restricter for using your unit as a blower.

1. Ensure unit is stopped and extension cord is unplugged.

2. Open the inlet cover by inserting the tip of a screwdriver into the latch area on the blower unit. Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand.

Bottom view of unit

Latch Area

/

Inlet Cover

.4

Vacuum

,n,et

Restrict_r /_ "_J/i

Attaching the vacuum tubes

There are 2 vacuum tubes, an upper tube and a lower tube. The upper tube has a vacuum assist handle attached to one end and is cut straight on both ends.

The upper tube attaches to the blower unit. The lower tube has an angled end that you point toward the ground during vacuum use.

The lower tube attaches to the upper tube.

1. Ensure unit is stopped and extension cord is unplugged.

2. While holding inlet cover open, place the hooks of the vacuum assist handle on the retaining posts of the unit.

Upper Vacuum Tube

'_ Vacuum Assist Handle

Hoo_

3. Pivot the tube until it is secured to the blower unit by the red inlet cover latch.

Vacuum Inlet Cover (closed)

Impeller

Latch Area

/

/

Vacuum Inlet Cover (opened)

3. Turn the inlet restrictor counterclockwise and remove it from the unit.

Do not close the inlet door. You will next attach the vacuum tubes.

4. Attach the lower vacuum tube to the upper vacuum tube by aligning the arrows on the two tubes.

Press the tubes together until the lower tube is fully seated in the upper tube.

About 3 inches)

_ Upper Tube Lower Tube

//

Align arrows on upper and lower tubes

COLLECTION BAG ASSEMBLY

1. Open the zipper on the collection bag and insert the elbow tube.

2. Push the small end ofthe elbow tube through the small opening in the bag.

NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube and the hole for the tube release button is on top.

Elbow Tube Tube

Release

Button

Hole

/

Zipper

Opening

Small

Opening

3. Close the zipper on the bag. Make sure the zipper is closed completely.

4. Align the grooves on the elbow tube with the grooves on the blower outlet.

5. Push the elbow tube onto the blower outlet until it snaps into place (elbow tube is secured by red tube release button).

ADJUSTING THE SHOULDER STRAP

ON THE COLLECTION BAG

1. Carefully loop the shoulder strap through the buckle as shown in the illustration below.

No kinks in allows free

HOW TO CONVERT UNIT FROM

VACUUM USE TO BLOWER USE

1. Stop unit and unplug the extension cord.

2. Remove the vacuum tubes by inserting the tip of a screwdriver into the latch area on the vacuum assist handle.

Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vacuum assist handle with your other hand.

Latch Area

J

Shoulder strap on left shoulder

Assist

Last In_

2. Position the unit on your right-hand side, blower outlet and bag pointing toward the rear.

Hold the unit in an upright position with the lower vacuum tube on the ground to support it.

3. Place the shoulder strap over your head and onto your left shoulder.

4. Adjust the strap to allow a free flow of air from the blower. If the collection bag is kinked, the unit will not operate properly.

NOTE: The strap is designed to position the collection bag on your shoulder without kinks. The strap is not intended to support the weight of the unit.

3. Remove the collection bag.

4. Install the inlet restrictor that was removed when assembling for vacuum use.

NOTE: If you are unable to locate the inlet restrictor, the unit will still operate.

This restrictor improves the blower function.

5. Close the inlet cover and make sure it is latched closed.

6. Re-install the blower tube. Refer to

ATTACHING THE BLOWER TUBE for instructions on how to attach this item.

SELECT AN EXTENSION CORD

Use only a 120 A.C. voltage supply as shown on nameplate of the unit to power your blower.

° To reduce the risk of electrical shock, this equipment has a polarized plug

(one blade is wider than the other) and will require the use of a polarized extension cord. The appliance plug will fit into a polarized extension cord only one way.

If the plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord.

extension theuseofapolarized plug onlyoneway.

intothewalloutlet, walloutlet notfitfully reverse itstilldoes toinstall extension extension theplug.

aqualified theproper

Donotchange wall theequipment cordpluginanyway.

Theextension power dooruse.

must

• Specifically

Thecordmust withthesuffix

• Heavy from tocarry

Otherwise, source canoccur cordmust lossofpower wiregauge totableforminimum recommendations.

bemarked wiregauge.

Donotusemulcords

(Appropriate areavailable.) tiplecords.

• Ingood must condition.

withnocracks deterioration.

cords.

Plug undamaged.

connectors

VOLTS

120 16

*American

A.W.G.*

Wire Gauge

WIRE

RECOMMENDATIONS

16

A.W.G.*

FT.

14

A.W.G.*

Secure the extension cord to the unit by threading the cord through the cord retainer (see illustration). Insert the cord receptacle into the recessed plug.

CAUTION: Failure to use cord retainer could result in damage to the unit, extension cord, or both.

C°rcdptaclec'f

Retainer-_

_ Recessed

KNOW YOUR ELECTRIC BLOWER

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

UNIT. Compare the illustrations to your unit to familiarize yourself with the location of the various controls and adjustments.

Save this manual for future reference.

ON/OFF Switch ....

Collection Bag

Co_d Q /'_--_- Air Vents

Rear /'" _

Handle _

Inlet Cover

Latch

,

upper vacuum

Retaining Post

Tube Release Button

Blower Tube

/

-'_ IlnletRestrictor

Vacuum Assist Handle

Tube

Upper Vacuum _

Lower Vacuum Tube

/

/

ON/OFF SWITCH

The ON/OFF SWITCH is used to activate the motor.

INLET COVER LATCH

The INLET COVER LATCH is used to open and close the inlet cover and to secure the upper vacuum tube to the blower unit.

BLOWER TUBE

The BLOWER TUBE is designed to direct the flow of air.

STOPPING YOUR

Slide the ON/OFF switch to the OFF position.

STARTING YOUR UNIT

Your unit has two run positions, LOW and HIGH. Slide the switch to one of these positions

A(_LWARNING:

,_WARNING:

Eye Protection

UNIT to turn on the unit.

Do not use the unit without the tubes or collection bag properly attached to avoid flying debris and/or impeller contact which can cause serious injury.

Always wear eye protection to prevent rocks or debris from being blown or ricocheting into the eyes and face which can result in blindness or serious injury.

OPERATING POSITION

Eye Protection

Blower Vacuum

USING YOUR UNIT AS A BLOWER

'_ WARNING: Inspect the area before using the unit.

Remove all debris and hard objects such as rocks, glass, wire, etc., that can ricochet, be thrown, or otherwise cause injury or damage during operation.

Use your unit as a blower for:

• Sweeping debris or grass clippings from driveways, sidewalks, patios, etc.

• Blowing grass clippings, straw, or leaves into piles, or removing debris from corners, around joints, or between bricks.

INLET RESTRICTOR

The INLET RESTRICTOR improves the blower function.

TUBE RELEASE BUTTON

The TUBE RELEASE BU-i-i-ON secures the blower tube or elbow tube to the blower unit during operation.

Also, pressing the tube release button allows removal of the blower tube or elbow tube.

Direct air flow by directing the blower tube down or to one side. Always work away from solid objects such as walks, large stones, vehicles, and fences.

Clean corners by starting in corners and moving outward. This will help prevent an accumulation of debris which could fly into your face.

Be careful when working near plants.

The force of the air could damage tender plants.

USING YOUR UNIT AS A VACUUM

_WARNING: Do not vacuum stones, gravel, metal, broken glass, etc., to avoid severe damage to the impeller.

To avoid the possibility of electrical shock, do not attempt to vacuum water or other liquids.

Use your unit as a vacuum to pick up dry material such as leaves, grass, small twigs, and bits of paper.

• For best results during vacuum use, operate your unit at high speed.

• Move slowly back and forth over the material as you vacuum.

Avoid forcing the unit into a pile of debris as this can clog the unit.

• Keep the vacuum tube about an inch above the ground for best results.

_LWARNING: If the unit becomes clogged, stop the unit and unplug the extension cord. Wait until the impeller has completely stopped turning, then remove the vacuum tubes.

Carefully reach into the vacuum opening and clear out the clogged debris.

CARE

TASK

Check for loose fasteners and parts

Check for damaged or worn parts

Inspect and clean unit and labels

Remove and empty collection bag

Clean collection bag

GENERAL RECOMMENDATIONS

The warranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain unit as instructed in this manual. Various adjustments will need to be made periodically to properly maintain your unit.

BEFORE EACH USE

CHECK FOR LOOSE

FASTENERS AND PARTS

• Inlet Cover

• Blower Tube

• Vacuum Tubes

• Collection Bag

CHECK FOR DAMAGED OR

WORN PARTS

Contact Sears Service Centre for replacement of damaged or worn parts.

• ON/OFF Switch - Ensure switch functions properly by moving the switch to the OFF position. Make sure motor stops; then restart motor and continue.

• Inlet Cover - Discontinue use of unit if inlet cover fails to latch properly or if it is damaged in any way.

WHEN TO PERFORM

Before each use

Before each use

After each use

After each use

Yearly

AFTER EACH USE

INSPECT AND CLEAN UNIT & LABELS

Stop unit and unplug extension cord.

• After each use, inspect complete unit for loose or damaged parts. Clean the unit using a damp cloth.

• Wipe off unit with a clean dry cloth.

CLEAN COLLECTION BAG

IMPORTANT: THE COLLECTION BAG

MUST BE PROPERLY EMPTIED.

• You must properly empty and maintain the collection bag to avoid deterioration and obstruction of air flow.

Remove the collection bag from the unit and empty after each use. Do not store bag without emptying the bag of all contents (grass, leaves, etc.).

Wash the bag once a year. Remove the bag from the blower and turn the bag inside out. Wash the bag with a water hose. Allow the bag to hang and dry completely before you reuse the bag.

HOW TO REMOVE AN OBJECT

FROM THE AIR INTAKE

_kWARNING: Stop the unit and disconnect from the power source before opening the inlet cover.

The motor must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades.

1. While holding the inlet cover open, remove the vacuum tubes.

The inlet cover must be held open through all remaining steps.

2. Carefully reach into the vacuum opening and clear out the air intake area.

Clear all debris from impeller.

3. Inspect the impeller for cracks.

If cracked or damaged, do not use the unit. Have parts replaced by your

Sears Service Centre.

Do not attempt to replace them yourself.

10

USER REPLACEABLE

REPLACEMENT PART

Blower Tube

Elbow Tube

SERVICE PARTS

Upper Vacuum Tube/

Vacuum Assist Handle

Lower Vacuum Tube

Inlet Restrictor

Collection Bag

PART NUMBER

530403765

530403769

530403842

530095589

530403791

530095599

_WARNING: Perform the following steps after each use:

• Stop unit and disconnect from the power source.

• Allow motor to cool before storing or transporting.

• Store unit with all guards in place.

Position unit so that any sharp object cannot accidentally cause injury.

• Store unit unplugged, well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at the end of the season or if it will not be used for

30 days or more.

If your blower is to be stored for a period of time:

• Stop unit and disconnect from the power source.

• Clean the entire unit before lengthy storage.

• Open inlet cover and clean any dirt, grass, or debris that has collected. Inspect the blower and all tubes. Close and make sure the cover is latched.

• Clean air vents and air inlet of debris.

• Store your unit and extension cord in a well ventilated area and covered, if possible, to prevent dust and dirt accumulation. Do not cover with plastic.

Plastic cannot breathe and may cause condensation and eventual rust or corrosion.

• Check entire unit for loose screws. Replace any damaged, worn, or broken parts.

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect from the power source before performing all of the recommended remedies below except remedies that require unit to be operating.

SYMPTOM

Unit fails to operate.

Unit vibrates abnormally.

CAUSE

1. Switch in the OFF position.

2. Extension cord disconnected.

3. Circuit breaker tripped, or fuse blown.

4. Mechanical failure

1. Mechanical failure

Impeller will 1. Debris in air intake area.

not turn 2. Mechanical failure, freely.

REMEDY

1. Slide switch to ON position.

2. Reconnect extension cord.

3. Reset circuit breaker or fuse.

4. Contact

Centre.

your Sears

1. Contact your Sears Service

Centre.

1. Clean unit. Remove debris.

Centre.

Service any

2. Contact your Sears Service

11