Raymarine C Series Installation manual

Raymarine C Series Installation manual
C-Series Widescreen
Multifunction Display
Installation instructions
C90W, C120W and C140W models
Trademarks and registered trademarks
Autohelm, HSB, RayTech Navigator, Sail Pilot, SeaTalk and Sportpilot are UK registered trademarks of Raymarine UK Limited.
Pathfinder and Raymarine are UK registered trademarks of Raymarine Holdings Limited. 45STV, 60STV, AST, Autoadapt, Auto GST,
AutoSeastate, AutoTrim, Bidata, G Series, HDFI, LifeTag, Marine Intelligence, Maxiview, On Board, Raychart, Raynav, Raypilot, RayTalk,
Raystar, ST40, ST60+, Seaclutter, Smart Route, Tridata, UniControl and Waypoint Navigation are trademarks of Raymarine UK Limited.
All other product names are trademarks or registered trademarks of their respective owners.
Copyright ©2008 Raymarine UK Ltd. All rights reserved.
ENGLISH
Document number: 87101-1
Date: November 2008
Contents
Chapter 1 Important Information............................. 7
TFT LCD Displays .......................................................... 8
Water ingress ................................................................. 8
Disclaimers .................................................................... 8
CompactFlash cards ....................................................... 9
EMC installation guidelines ............................................. 9
Suppression ferrites ........................................................ 10
Connections to other equipment ...................................... 10
Declaration of conformity................................................. 10
Product disposal ............................................................. 10
Warranty registration....................................................... 10
IMO and SOLAS............................................................. 11
Technical accuracy ......................................................... 11
Chapter 2 Planning the installation ........................ 13
2.1 Handbook information ............................................... 14
2.2 Installation checklist .................................................. 14
2.3 C-Series systems...................................................... 15
2.4 Pack contents ........................................................... 17
2.5 Tools ........................................................................ 19
Chapter 3 Cables and connections......................... 21
3.1 General cabling guidance .......................................... 22
3.2 Connections overview ............................................... 23
3.3 Power connection ..................................................... 23
3.4 SeaTalkhs network ..................................................... 26
3.5 NMEA 0183 connection ............................................. 32
3.6 SeaTalk connection ................................................... 33
3.7 Alarm connection ...................................................... 34
3.8 GPS connection ........................................................ 35
3.9 AIS connection.......................................................... 36
3.10 Fastheading connection........................................... 36
3.11 SeaTalkng connections ............................................. 37
3.12 NMEA 2000 connection ........................................... 38
3.13 Video connection..................................................... 39
Chapter 4 Location and mounting .......................... 41
4.1 Selecting a location ................................................... 42
4.2 Flush mounting ......................................................... 45
4.3 Bracket (trunnion) mounting....................................... 46
4.4 Front bezel ............................................................... 48
Chapter 5 System checks ........................................ 51
5.1 Initial power on test ................................................... 52
5.2 GPS check ............................................................... 53
5.3 Radar check ............................................................. 54
5.4 Sonar check ............................................................. 56
5.5 Language selection ................................................... 57
5
Chapter 6 Troubleshooting...................................... 59
Appendix C NMEA 2000 sentences ........................ 87
6.1 Troubleshooting ........................................................ 60
6.2 Power up troubleshooting .......................................... 60
6.3 Radar troubleshooting ............................................... 61
6.4 GPS troubleshooting ................................................. 62
6.5 Sonar troubleshooting ............................................... 63
6.6 System data troubleshooting...................................... 64
6.7 SeaTalkhs LED indications.......................................... 65
6.8 Miscellaneous troubleshooting ................................... 66
Chapter 7 Technical support ................................... 69
7.1 Raymarine technical support...................................... 70
7.2 Sirius support............................................................ 70
7.3 Navionics support ..................................................... 71
Chapter 8 Technical specification........................... 73
8.1 Technical specification............................................... 74
Chapter 9 Options and accessories ....................... 77
9.1 SeaTalk accessories.................................................. 78
9.2 SeaTalkng accessories ............................................... 78
9.3 SeaTalkhs accessories ............................................... 79
9.4 Spares and accessories ............................................ 81
Appendix A Connectors and pinouts ..................... 83
Appendix B NMEA 0183 sentences ........................ 85
6
C-Series Widescreen installation
Chapter 1: Important Information
Warning: Product installation
This equipment must be installed in accordance with
the Raymarine instructions provided. Failure to do so
could result in poor product performance, personal
injury, and/or damage to the vessel.
Warning: Switch off power supply
Ensure the boat’s power supply is switched OFF
before starting to install this product. Do NOT connect
or disconnect equipment with the power switched on,
unless instructed in this document.
Warning: Radar scanner safety
Warning: Potential ignition source
Before rotating the radar scanner, ensure all personnel
are clear.
This product is NOT approved for use in
hazardous/flammable atmospheres. Do NOT install in
a hazardous/flammable atmosphere (such as in an
engine room or near fuel tanks).
Warning: Radar transmission safety
Warning: High voltages
This product contains high voltages. Do NOT remove
any covers or otherwise attempt to access internal
components, unless specifically instructed in this
document.
Warning: Grounding
This display is not intended for use on “positive”
ground boats. The power input cable drain wires must
be connected directly to the boats ground.
The radar scanner transmits electromagnetic energy.
Ensure all personnel are clear of the scanner when
the radar is transmitting.
Warning: Sonar operation
• NEVER operate the sounder with the boat out of
the water.
• NEVER touch the transducer face when the sounder
is powered on.
• SWITCH OFF the sounder if divers are likely to be
within 25 ft (5 m) of the transducer.
Caution: Power supply protection
When installing this product ensure the power
source is adequately protected by means of a
suitably-rated fuse or automatic circuit breaker.
Important Information
7
Caution: Care of chart cards
Caution: Cleaning
To avoid irreparable damage to and/or loss of data
from chart cards:
When cleaning this product do NOT use acid,
ammonia-based or abrasive products, and do NOT
use high pressure washing (jet wash) equipment.
• Ensure that chart cards are fitted the correct way
around. DO NOT try to force a card into position.
• DO NOT save data (waypoints, routes, and so
on) to a Navionics chart card, as the charts may
be overwritten.
TFT LCD Displays
• DO NOT use a metallic instrument such as a
screwdriver or pliers to remove a chart card.
The colors of the display may seem to vary when viewed against
a colored background or in colored light. This is a perfectly normal
effect that can be seen with all color Liquid Crystal Displays (LCDs).
• DO NOT remove a chart card while information
is being written to or read from it.
Caution: Ensure chart card door is
securely closed
To prevent water ingress and consequent damage
to the display, ensure that the chart card door is
firmly closed. This can be confirmed by an audible
click.
In common with all Thin Film Transistor (TFT) LCD units, the screen
may exhibit a few (less than 7) wrongly illuminated pixels. These
may appear as black pixels in a light area of the screen or as colored
pixels in black areas.
Water ingress
Caution: Use the sun covers
As it exceeds the water proof rating capacity outlined by standards
IPX6, subjecting any Raymarine equipment to commercial
high pressure washing equipment may cause water intrusion
and subsequent equipment failure. Raymarine will not warrant
equipment subjected to high pressure washing.
To protect your product against the damaging
effects of ultra violet light, always fit the sun
covers when the product is not in use.
Disclaimers
This product (including the electronic charts) is intended to be used
only as an aid to navigation. It is designed to facilitate use of official
government charts, not replace them. Only official government
charts and notices to mariners contain all the current information
needed for safe navigation, and the captain is responsible for their
8
C-Series Widescreen installation
prudent use. It is the user’s responsibility to use official government
charts, notices to mariners, caution and proper navigational skill
when operating this or any other Raymarine product. This product
supports electronic charts provided by third party data suppliers
which may be embedded or stored on memory card. Use of such
charts is subject to the supplier’s End-User Licence Agreement
included in the documentation for this product or supplied with the
memory card (as applicable).
Raymarine does not warrant that this product is error-free or that it
is compatible with products manufactured by any person or entity
other than Raymarine.
This product uses digital chart data, and electronic information from
the Global Positioning System (GPS) which may contain errors.
Raymarine does not warrant the accuracy of such information and
you are advised that errors in such information may cause the
product to malfunction. Raymarine is not responsible for damages
or injuries caused by your use or inability to use the product, by the
interaction of the product with products manufactured by others, or
by errors in chart data or information utilized by the product and
supplied by third parties.
CompactFlash cards
Navionics chart cards
The Display is pre-loaded with Navionics chart data. If you wish to
use different chart data, you can insert Navionics chart cards into
the CompactFlash card slot on the unit.
EMC installation guidelines
Raymarine equipment and accessories conform to the appropriate
Electromagnetic Compatibility (EMC) regulations, to minimize
electromagnetic interference between equipment and minimize the
effect such interference could have on the performance of your
system
Correct installation is required to ensure that EMC performance is
not compromised.
For optimum EMC performance we recommended that wherever
possible:
• Raymarine equipment and cables connected to it are:
– At least 1 m (3 ft) from any equipment transmitting or cables
carrying radio signals e.g. VHF radios, cables and antennas.
In the case of SSB radios, the distance should be increased
to 7 ft (2 m).
– More than 2 m (7 ft) from the path of a radar beam. A radar
beam can normally be assumed to spread 20 degrees above
and below the radiating element.
• The product is supplied from a separate battery from that used
for engine start. This is important to prevent erratic behavior
and data loss which can occur if the engine start does not have
a separate battery.
• Raymarine specified cables are used.
• Cables are not cut or extended, unless doing so is detailed in
the installation manual.
Use branded chart cards
When archiving data, Raymarine recommends the use of SanDisk
CF memory cards. Other brands of CF memory card may not work
in your unit.
Important Information
9
Note: Where constraints on the installation prevent any of
the above recommendations, always ensure the maximum
possible separation between different items of electrical
equipment, to provide the best conditions for EMC performance
throughout the installation
The original Declaration of Conformity certificate may be viewed on
the relevant product page at www.raymarine.com
Product disposal
Dispose this product in accordance with the WEEE Directive.
Suppression ferrites
Do not remove ferrite
Raymarine cables may be fitted with suppression ferrites. These
are important for correct EMC performance. If a ferrite has to be
removed for any purpose (e.g. installation or maintenance), it must
be replaced in the original position before the product is used.
The Waste Electrical and Electronic Equipment (WEEE)
Directive requires the recycling of waste electrical and electronic
equipment. Whilst the WEEE Directive does not apply to some
Raymarine products, we support its policy and ask you to be aware
of how to dispose of this product.
Use only ferrites of the correct type, supplied by Raymarine
authorized dealers.
Warranty registration
Connections to other equipment
Requirement for ferrites on non-Raymarine cables
To register your C-Series multifunction display ownership, please
take a few minutes to fill out the warranty registration card found in
the box, or visit www.raymarine.com and register on-line.
If your Raymarine equipment is to be connected to other equipment
using a cable not supplied by Raymarine, a suppression ferrite
MUST always be attached to the cable near the Raymarine unit.
Declaration of conformity
Raymarine Ltd. declares that the C-Series Multifunction Displays
are in compliance with the essential requirements of EMC directive
2004/108/EC.
10
C-Series Widescreen installation
It is important that you register your product to receive full warranty
benefits. Your unit package includes a bar code label indicating the
serial number of the unit. You should stick this label to the warranty
registration card.
IMO and SOLAS
The equipment described within this document is intended for use
on leisure marine boats and workboats not covered by International
Maritime Organization (IMO) and Safety of Life at Sea (SOLAS)
Carriage Regulations.
Technical accuracy
To the best of our knowledge, the information in this document was
correct at the time it was produced. However, Raymarine cannot
accept liability for any inaccuracies or omissions it may contain. In
addition, our policy of continuous product improvement may change
specifications without notice. As a result, Raymarine cannot accept
liability for any differences between the product and this document.
Important Information
11
12
C-Series Widescreen installation
Chapter 2: Planning the installation
Chapter contents
•
2.1 Handbook information on page 14
•
2.2 Installation checklist on page 14
•
2.3 C-Series systems on page 15
•
2.4 Pack contents on page 17
•
2.5 Tools on page 19
Planning the installation
13
2.1 Handbook information
2.2 Installation checklist
This handbook contains important information on installing the
C-Series Widescreen range of multifunction displays.
Installation includes the following activities:
Installation Task
The handbook is for use with the following models:
• C90W Widescreen Multifunction Display
1
Plan your system
• C120W Widescreen Multifunction Display
2
Obtain all required equipment and tools
• C140W Widescreen Multifunction Display
3
Site all equipment
4
Route all cables.
C-Series handbooks
5
Drill cable and mounting holes.
The C-Series Widescreen Multifunction Display has the following
handbooks available.
6
Make all connections into equipment.
7
Secure all equipment in place.
8
Power on test the system.
All documents are available to download as PDFs from
www.raymarine.com
C-Series handbooks
Description
Part number
Installation and commissioning
instructions
87101
Operating instructions (quick
reference)
86135
User reference handbook
81312
Additional handbooks
Description
Part number
SeaTalkng reference manual
81300
14
C-Series Widescreen installation
2.3 C-Series systems
The C-Series display can be used in a number of system types.
Some examples are outlined here.
Example system
Radar
C-Series display
SeaTalkng backbone
Pilot
CANCEL
ENTER
SeaTalkhs
DSM 300
Crossover Coupler
SeaTalkhs
Power & Data Multi cable
MENU
SeaTalkng
Instrument
CANCEL
ENTER
MENU
SeaTalkng
GPS
Alarm
Video
AIS receiver
NMEA 0183
NMEA or
SeaTalk
Power
D11199-1
Planning the installation
15
C-Series protocols
Your C-Series Widescreen Multifunction Display can connect to
various instruments and displays to share information and so
improve the functionality of the system. These connections may be
made using a number of different protocols. Fast and accurate data
collection and transfer is achieved by using a combination of the
following data protocols:
SeaTalkng utilizes a single backbone cable to which compatible
instruments connect using a spur. Data and power are carried within
the backbone. Devices that have a low draw can be powered from
the network, although high current equipment will need to have a
separate power connection.
• SeaTalkhs
SeaTalkng is a proprietary extension to NMEA 2000 and the proven
CAN bus technology. Compatible NMEA 2000 and SeaTalk /
SeaTalk2 devices can also be connected using the appropriate
interfaces or adaptor cables as required.
• SeaTalkng
NMEA 2000
• NMEA 2000
NMEA 2000 offers significant improvements over NMEA 0183, most
notably in speed and connectivity. Up to 50 units can simultaneously
transmit and receive on a single physical bus at any one time,
with each node being physically addressable. The standard
was specifically intended to allow for a whole network of marine
electronics from any manufacturer to communicate on a common
bus via standardized message types and formats.
• SeaTalk
• NMEA 0183
Note: You may find that your system does not use all of the
connection types or instrumentation described in this section.
SeaTalk
SeaTalkhs
SeaTalkhs is an ethernet based marine network. This high speed
protocol allows compatible equipment to communicate rapidly and
share large amounts of data.
Information shared using the
SeaTalkhs
network includes:
• Shared cartography (between compatible displays.
SeaTalk is a protocol which enables compatible instruments to
connect to each other and share data.
The SeaTalk cable system is used to connect compatible
instruments and equipment. The cable carries power and data and
enables connection without the need for a central processor.
• Sonar data.
Additional instruments and functions can be added to a SeaTalk
system, simply by plugging them into the network. SeaTalk
equipment can also communicate with other non-SeaTalk equipment
via the NMEA 0183 standard, provided a suitable interface is used.
Seatalkng
NMEA 0183
SeaTalkng (New Generation) is an enhanced protocol for connection
of compatible marine instruments and equipment. It replaces the
older SeaTalk and SeaTalk2 protocols.
The NMEA 0183 Data Interface Standard was developed by
the National Marine Electronics Association of America. It is an
international standard to enable equipment from many different
manufacturers to be connected together and share information.
• Digital radar data.
16
C-Series Widescreen installation
The NMEA 0183 standard carries similar information to SeaTalk.
However it has the important difference that one cable will only
carry information in one direction. For this reason NMEA 0183 is
generally used to connect a data receiver and a transmitter together,
e.g. a compass sensor transmitting heading to a radar display. This
information is passed in ‘sentences’, each of which has a three
letter sentence identifier. It is therefore important when checking
compatibility between items that the same sentence identifiers are
used some examples of which are:
2.4 Pack contents
Unpack the display unit carefully to prevent damage. Save the
carton and packing in case the unit has to be returned for service.
• VTG - carries Course and Speed Over Ground data.
• GLL - carries latitude and longitude.
• DBT - carries water depth.
• MWV - carries relative wind angle and wind speed data.
NMEA baud rates
The NMEA 0183 standard operates at a number of different
speeds, depending upon the particular requirement or equipment
capabilities. Typical examples are:
• 4800 baud rate. Used for general purpose communications,
including FastHeading data.
• 9600 baud rate. Used for Navtex.
• 38400 baud rate. Used for AIS and other high speed applications.
Planning the installation
17
All models contain the following items:
Description
Bezel
Gasket
Suncover
1.5 m (4.9 ft) Power and data cable
Screw pack
Document pack, includes:
Gasket
• Multilingual CD
• Installation instructions
C-Series
Widescreen display
• Cutting template
Micro fiber cleaning cloth
Bezel
Marine shield screen clean sample (North America only)
Suncover
Power and Data multi-cable
MARINE
Micro fiber
dry cleaning
cloth
Document Pack
Flush mount
screw pack
S HIELD
2oz sample
“Marine Shield
”
screen cleaner
(North America Only)
D11194-1
Description
C-Series Widescreen Multifunction Display
18
C-Series Widescreen installation
2.5 Tools
Tools required for installation
Power
drill
Jig
saw
Adhesive tape
drill bit,
bracket mounting
Screwdriver
File
35 mm (1.3/8 in)
5 mm (3/16 in) drill bit,
hole cutter, bracket mounting
panel mounting
D11580-1
Planning the installation
19
20
C-Series Widescreen installation
Chapter 3: Cables and connections
Chapter contents
•
3.1 General cabling guidance on page 22
•
3.2 Connections overview on page 23
•
3.3 Power connection on page 23
•
3.4 SeaTalkhs network on page 26
•
3.5 NMEA 0183 connection on page 32
•
3.6 SeaTalk connection on page 33
•
3.7 Alarm connection on page 34
•
3.8 GPS connection on page 35
•
3.9 AIS connection on page 36
•
3.10 Fastheading connection on page 36
•
3.11 SeaTalkng connections on page 37
•
3.12 NMEA 2000 connection on page 38
•
3.13 Video connection on page 39
Cables and connections
21
3.1 General cabling guidance
• Do NOT run cables near to engines or fluorescent lights.
Always route data cables as far away as possible from:
Cable types and length
• other equipment and cables,
It is important to use cables of the appropriate type and length
• high current carrying ac and dc power lines,
• Unless otherwise stated use only standard cables of the correct
type, supplied by Raymarine.
• Ensure that any non-Raymarine cables are of the correct quality
and gauge. For example, longer power cable runs may require
larger wire gauges to minimize voltage drop along the run.
• antennae.
Strain relief
Ensure adequate strain relief is provided. Protect connectors from
strain and ensure they will not pull out under extreme sea conditions.
Routing cables
Cables must be routed correctly, to maximize performance and
prolong cable life.
• Do NOT bend cables excessively. Wherever possible, ensure a
minimum bend radius of 100 mm.
Minimum bend
200 mm (8 in)
diameter
Appropriate circuit isolation is required for installations using both
AC and DC current:
• Always use isolating transformers or a separate power-inverter
to run PC’s, processors, displays and other sensitive electronic
instruments or devices.
• Always use an isolating transformer with Weather FAX audio
cables.
Minimum bend of cable
100 mm (4 in) radius
• Protect all cables from physical damage and exposure to heat.
Use trunking or conduit where possible. Do NOT run cables
through bilges or doorways, or close to moving or hot objects.
• Secure cables in place using tie-wraps or lacing twine. Coil any
extra cable and tie it out of the way.
• Where a cable passes through an exposed bulkhead or deckhead,
use a suitable watertight feed-through.
22
Circuit isolation
• Always use an RS232/NMEA converter with optical isolation on
the signal lines.
• Always make sure that PC’s or other sensitive electronic devices
have a dedicated power circuit.
Cable shielding
Ensure that all data cables are properly shielded that the cable
shielding is intact (e.g. hasn’t been scraped off by being squeezed
through a tight area).
C-Series Widescreen installation
3.3 Power connection
3.2 Connections overview
Cable connectors are on the rear of the display
C-Series display
19 way multi-cable
1
1. SeaTalkng
2
3
4
7Afuse
D11189-1
Data and video
2. Power and data
Red
Black
12 V
supply
D11210-1
3. SeaTalkhs
Power distribution
4. SeaTalkhs
Raymarine recommend that all power connections are made via a
distribution panel.
• All equipment must be powered from a breaker or switch, with
appropriate circuit protection.
• All equipment should where possible be wired to individual
breakers.
Cables and connections
23
Warning: Grounding
• Cable must be of a suitable gauge for the circuit load.
This display is not intended for use on “positive”
ground boats. The power input cable drain wires must
be connected directly to the boats ground.
• Each unit should have its own dedicated power cable wired back
to the distribution panel.
Grounding
The following requirements apply when grounding Raymarine
equipment:
• Use a dedicated earthing plate (e.g. dynaplate) in contact with
the water.
• Ground cables may be routed to a common point (e.g. within the
switch panel. With a single (appropriately rated) copper braid
connecting to the earthing plate.
• Use flat tinned copper braid, 30 A rating (1/4 inch) or greater.
Equivalent stranded wire diameter 4 mm or greater.
• Keep the length of the earth braid as short as possible.
Power cable
The C-Series display is supplied with a combined power and data
multi cable, this can be extended if required.
Power cable supplied
Cable
Part number
Notes
1.5 m (4.9 ft) Power and
data cable
R62131
Supplied with C-Series
unit
Total length (max)
Supply voltage
Cable gauge
(AWG)
0–5 m (0–16.4 ft)
12 V
18
24 V
20
12 V
14
24 V
18
12 V
12
24 V
16
12 V
12
24 V
14
5–10 m (16.4–32.8 ft)
10–15 m (32.8–49.2 ft)
15–20 m (49.2–65.5 ft)
Note: These distances are for a 2 wire power cable run from the battery to
the display (approximately the distance from the battery to the display). To
calculate the round trip length, double the figure stated here.
Breakers, fuses and circuit protection
The C-Series Widescreen power cable includes an in-line fuse. You
can use an additional thermal breaker or fuse at the distribution
panel if you wish.
Cable extension
The following restrictions apply to any extension to the power cable:
24
C-Series Widescreen installation
Display
Fuse
• C90W
7 A in-line fuse fitted within power
cable.
• C120W
• C140W
Sharing a breaker
Where more than 1 piece of equipment shares a breaker you must
provide protection for the individual circuits. E.g. an in-line fuse for
each power circuit
+VE bar
-VE bar
Monitors and ancilliary equipment where
possible be wired to individual breakers.
Where this not possible an inline FUSE
can be used to provide additional portection.
Fuse
Cables and connections
Fuse
D10164-1
Circuit breaker
25
3.4 SeaTalkhs network
The SeaTalkhs network allows you to network compatible displays
and other digital devices.
The C-Series Widescreen Display can use SeaTalkhs to connect to:
• Another C-Series Widescreen Display.
• A digital radar scanner.
• A DSM300 or DSM30 sonar module.
• A SeaTalkhs switch.
Typical SeaTalkhs network
Radar
Master C-Series display
SeaTalkhs
C-Series display
SeaTalkhs
DSM300
Crossover Coupler
POWER
SeaTalk
NMEA0183
Alarm buzzer output
Video input
SeaTalkng
POWER
Multi cable
Multi cable
SeaTalkhs
D11214-1
26
C-Series Widescreen installation
SeaTalkhs display to display cables
Radar connection
You can connect up to 2 C-Series Widescreen displays together
using SeaTalkhs. Connect the displays directly or use a SeaTalkhs
switch.
C-Series Widescreen displays are compatible with Raymarine digital
radar scanners. The scanner is connected using a SeaTalkhs cable.
SeaTalkhs
network cables
Connect from the SeaTalkhs switch into the rear of the display.
Cable
Part number
1.5 m (4.9 ft) SeaTalkhs
network cable
E55049
5 m (16.4 ft) SeaTalkhs
network cable
E55050
10 m (32.8 ft) SeaTalkhs
network cable
E55051
20 m () SeaTalkhs
network cable
E55052
Notes
The digital radar can be connected either directly to the C-Series
display or via a SeaTalkhs switch.
Radar connected directly to the C-Series unit
Note: The connector on the free end of the radar cable does not
have a locking / weather tight mechanism. The use of a crossover
coupler is important to create a weather proof connection.
Fully waterproof SeaTalkhs network cables
Connect directly from display to display.
Cable
Part number
Notes
1.5 m (4.9 ft) Dual end
SeaTalkhs network cable.
A62245
Cable has waterproof
connectors at both ends.
15 m (49.2 ft) Dual end
SeaTalkhs network cable
A62246
Cable has waterproof
connectors at both ends.
Cables and connections
27
Radar connected using SeaTalkhs switch
Radar
Radar
HS switch
C-Series display
C-Series display
SeaTalkhs
Crossover
Coupler
12/24V power
D11372-1
12/24V power
D11218-1
28
C-Series Widescreen installation
Digital radar cables
Cable
Part number
You will need at least 2 cables to connect the digital radar scanner.
One cable connects the scanner to a SeaTalkhs switch (or cross
over coupler). The second cable then connects into the display.
2.5 m (8.2 ft) extension
cable
A92141
5 m (16.4 ft) extension
cable
A55080
10 m (32.8 ft) extension
cable
A55081
Note: The maximum cable length including all extensions is 25 m
(82 ft).
Radar scanner to SeaTalkhs switch (or cross over coupler)
Notes
Digital scanner cables
SeaTalkhs switch (or cross over coupler) to display unit
Connect the Radar scanner to the SeaTalkhs switch (or cross over coupler) and
power supply. These cables contain both power and data wires.
SeaTalkhs network cables
Cable
Part number
5 m (16.4 ft) Digital cable
A55076
10 m (32.8 ft) Digital
cable
A55077
15 m (49.2 ft) Digital
cable
A55078
25 m (82.0 ft) Digital
cable
A55079
Notes
Your radar scanner may
include the 10 m cable
(depending upon the
model purchased)
Extension cables
Use of one of these cables to extend the radar connection to the SeaTalkhs switch
(or cross over coupler) and power supply. These cables contain both power and
data wires.
Cables and connections
Connect from the SeaTalkhs switch or the cross over coupler into the rear of the
display.
Cable
Part number
1.5 m (4.9 ft) SeaTalkhs
network cable
E55049
5 m (16.4 ft) SeaTalkhs
network cable
E55050
10 m (32.8 ft) SeaTalkhs
network cable
E55051
20 m (65.6 ft) SeaTalkhs
network cable
E55052
Notes
SeaTalkhs hardware
To connect the digital radar to the C-Series display you will need
to include one of the following
29
Cable
Part number
Notes
SeaTalkhs switch
E55058
8 way hub for network
connection of multiple
SeaTalkhs devices.
SeaTalkhs coupler
E55060
Couple for connection
of a single SeaTalkhs
device.
C-Series display
Sonar connection
The sonar connection is required for fishfinder applications. The
C-Series display is connected to a sonar module (DSM) using a
SeaTalkhs cable. You will also require a compatible transducer
connected to the DSM unit.
DSM300
SeaTalkhs
D11219-1
The C-Series display can be used with the following DSM units
• DSM300
• DSM30
The C-Series can support 1 DSM module
30
C-Series Widescreen installation
Typical DSM system
C Series Display Unit
DSM300
Cable
Part number
10 m (32.8 ft) SeaTalkhs
network cable
E55051
20 m (65.6 ft) SeaTalkhs
network cable
E55052
Notes
Fully waterproof SeaTalkhs network cables
Connect directly from DSM to the rear of the display.
Transducer
SeaTalkhs Cable
Cable
Part number
Notes
1.5 m (4.9 ft) SeaTalkhs
network cable.
A62245
Cable has waterproof
connectors at both ends.
10 m (32.8 ft) SeaTalkhs
network cable
A62246
Cable has waterproof
connectors at both ends.
D11584-1
Sonar cable
Connect the DSM unit directly to your display, or connect via the
SeaTalkhs switch.
SeaTalkhs network cables
Connect from the SeaTalkhs switch into the rear of the display.
Cable
Part number
1.5 m (4.9 ft) SeaTalkhs
network cable
E55049
5 m (16.4 ft) SeaTalkhs
network cable
E55050
Cables and connections
Notes
31
3.5 NMEA 0183 connection
The C-Series has 3 NMEA ports available:
Connections to NMEA 0183 devices are made using the supplied
Power and data cable.
• Port 1: Input and output, 4800 / 9600 baud rate.
• Port 2: Input and output, up to 38400 baud rate.
• Port 3: Input only, 4800 baud rate.
NMEA 0183 cable
You can extend the NMEA 0183 wires within the supplied power
and data cable.
C-Series display
Data cable extension
The following restrictions apply to any extension to the NMEA 0183 data wires.
White Green Yellow Brown
IN
IN
OUT OUT
+ve
-ve
+ve
-ve
OUT
+ve
OUT
-ve
IN
+ve
NMEA
DEVICE
4800/9600 baud
IN
-ve
Orange/
Orange/
Blue/
Green
Brown
Green
IN
OUT
IN
-ve
-ve
-ve
Orange/
Orange/
Blue/
White
Yellow
White
IN
OUT
IN
+ve
+ve
+ve
OUT
+ve
OUT
-ve
IN
+ve
IN
-ve
NMEA
DEVICE
4800/9600/38400 baud
OUT
+ve
Total length (max)
Cable
Up to 5 m
High quality data cable:
• 2 x twisted pair with overall shield.
• 50 to 75 pF/m capacitance core to
core.
OUT
-ve
NMEA
DEVICE
4800 baud
(transmit to
C-Series
only)
D11200-1
32
C-Series Widescreen installation
3.6 SeaTalk connection
SeaTalk cable
Connections to SeaTalk equipment are made using the supplied
multi-cable.
For SeaTalk cables and extensions, use Raymarine SeaTalk cable
accessories.
Note: Power to SeaTalk instruments is not provided by the
C-Series Widescreen Display.
C-Series display
19 way multi-cable
Power, data and video
White/Red
Red
White/Black
Black
White/Y
ellow
Yellow
SeaTalk devices
5 A fused,
12 V dc supply
D11215-1
Cables and connections
33
3.7 Alarm connection
Typical alarm connection
An alarm buzzer can be connected using the power / data cable
provided with the display.
C-Series display
19 way multi-cable
Power, data and video
Grey
Black
Red
Black
Black
-ve supply
(from battery/
breaker)
Alarm
D11216-1
Note: The alarm output is rated for 100 mA maximum load
34
C-Series Widescreen installation
High alarm loads and third party alarms
3.8 GPS connection
You can use the alarm output to switch a relay. This may be useful
for connecting high loads such as third party alarm sounders or
inductive loads to the C-Series multifunction display. If you are in
any doubt as to how to make such connections please consult an
authorized installer.
Depending upon your GPS type it may be either connected via
SeaTalk or NMEA 0183.
The C-Series multifunction display has a positive switched alarm
output. The following circuit shows the arrangement for connection
of a relay switch.
See also
• For SeaTalk connection refer to: 3.6 SeaTalk connection.
• For NMEA 0183 connection refer to: 3.5 NMEA 0183 connection.
Alarm output configured to switch a relay
Alarm out
(+ve)
Battery+
Relay
Suppression
diode
0v return
Battery--
D11591-1
High current load
Note: When connecting the output to a relay or other inductive
device you should fit a spike suppression diode e.g. 1N4001.
Cables and connections
35
3.9 AIS connection
3.10 Fastheading connection
A compatible AIS can be connected using NMEA 0183.
Fastheading data required for radar target acquisition (MARPA) may
come from either the autopilot or a separate Raymarine Fastheading
sensor.
NMEA0183 (4800)
e.g GPS data to VHF radio
VHF antenna
Typical fastheading from NMEA 0183 compatible autopilot
AIS receiver
C Series display
VHF radio
Autopilot
VHF (antenna signal)
C Series display
NMEA0183
Pilot control head
Fluxgate compass
NMEA0183 (4800)
e.g.fast heading
CANCEL
ENTER
MENU
NMEA0183 (38400)
D11221-1
D11220-1
Note: The connection can be made into any NMEA 0183 port.
36
C-Series Widescreen installation
3.11 SeaTalkng connections
The C-Series Widescreen Display can connect as part of a
SeaTalkng network.
Typical SeaTalkng system
ST70
Instrument
ST70
Pilot Controller
Transducer
Pod
Wind
Transducer
The C-Series can use SeaTalkng to communicate with:
CANCEL
ENTER
CANCEL
MENU
ENTER
MENU
• SeaTalkng instruments (e.g. ST70)
• SeaTalkng autopilots (e.g. ST70 with SmartPilot SPX course
computer)
C Series
Display
Autopilot
(Course
Computer)
Power Supply
12 V dc + Data
12 V / 24 V dc
SeaTalkng backbone
Transducer
Pod
Depth
Transducer
Transducer
Pod
Speed
Transducer
D11195-1
Cables and connections
37
3.12 NMEA 2000 connection
SeaTalkng cables
NMEA 2000 devices are connected using the SeaTalkng bus. The
display can receive data from NMEA 2000 devices (e.g. data from
compatible engines). You may connect NMEA 2000 compatible
devices using appropriate adaptor cables
Connection / Cable
Notes
Backbone cables (various lengths)
The main cable carrying data. Spurs
from the backbone are used to
connect SeaTalkng devices.
T-piece connectors
Used to make junctions in the
backbone to which devices can then
be connected.
Terminators
Required at either end of the
backbone.
Spur cables
Used to connect devices. Devices
may be daisy chained or connected
directly to the T-pieces.
Seatalkng power
The SeaTalkng bus requires a 12 V power supply. This may be
provided from:
• Raymarine equipment with a regulated 12 V supply. (e.g. a
SmartPilot SPX course computer)
SeaTalkng backbone
SeaTalkng cabling
SeaTalkng
to DeviceNet cable
NMEA 2000
equipment
(e.g. engine via
appropriate
manufacturers
interface)
• Other suitable 12 V supply.
D11198-1
Note: SeaTalkng does NOT supply power to multifunction displays
and other equipment with a dedicated power supply input.
38
C-Series Widescreen installation
3.13 Video connection
The C-Series has an input for connection of cameras or other
types of video equipment. The video connection is made using
the combined power and data cable supplied with the unit. The
connection is compatible with NTSC and PAL equipment.
Video connection
C-Series display
19 way
multi-cable
Power, data and video
BNC
D11222-1
Cables and connections
39
40
C-Series Widescreen installation
Chapter 4: Location and mounting
Chapter contents
•
4.1 Selecting a location on page 42
•
4.2 Flush mounting on page 45
•
4.3 Bracket (trunnion) mounting on page 46
•
4.4 Front bezel on page 48
Location and mounting
41
4.1 Selecting a location
Warning: Potential ignition source
This product is NOT approved for use in
hazardous/flammable atmospheres. Do NOT install in
a hazardous/flammable atmosphere (such as in an
engine room or near fuel tanks).
General location requirements
When selecting a location for your display it is important to consider
a number of factors.
Key factors which can affect product performance are:
• Ventilation
To ensure adequate airflow:
– Ensure that equipment is mounted in a compartment of suitable
size.
– Ensure that ventilation holes are not obstructed. Allow
adequate separation of equipment.
Any specific requirements for each system component are
provided later in this chapter.
– Minimum bend radius of 100 mm (3.94 in) unless otherwise
stated.
– Use cable supports to prevent stress on connectors.
• Water ingress
The display is suitable for mounting both above and below decks.
It is waterproof to IPX6 standard. Although the unit is waterproof,
it is good practice to locate it in a protected area away from
prolonged and direct exposure to rain and salt spray.
• Viewing angle
The contrast and colors seen on all LCD units varies slightly with
viewing angle and are best viewed perpendicular to the display.
Avoid locations where excessive reflection will occur in normal use
• Electrical interference
Select a location that is far enough away from devices that
may cause interference, such as motors, generators and radio
transmitters/receivers.
• Magnetic compass
Select a location that is at least 3 ft (1 m) away from a magnetic
compass.
• Power supply
• Mounting surface.
Ensure equipment is adequately supported on a secure surface.
Do not mount units or cut holes in places which may damage the
structure of the vessel.
• Cable entry
Ensure the unit is mounted in a location which allows proper
routing and connection of cables:
42
C-Series Widescreen installation
Select a location that is as close as possible to the boat’s DC
power source. This will help to keep cable runs to a minimum
Mounting location
• Above Decks mounting.
Provides optimal GPS performance. (For equipment with
appropriate waterproof rating.)
C-Series Widescreen dimensions
C90W, C120W and C140W dimensions
• Below Decks mounting.
C
E
B
Provides good performance with GRP construction vessels,
however GPS may be less effective in poor prevailing conditions.
D
A
A
B
C
D
E
C90
12.45 in
(316 mm)
7.74 in
(197 mm)
4.43 in
(113 mm)
6.14 in
(156 mm)
8.3 in
(211 mm)
C120
14.97 in
(380 mm)
10.0 in
(245 mm)
4.43 in
(113 mm)
6.14 in
(156 mm)
10.2 in
(260 mm)
C140
16.66 in
(423 mm)
10.9 in
(277 mm)
4.43 in
(113 mm)
6.14 in
(156 mm)
11.46 in
(291 mm)
Model
Note: Below decks mounting on vessels of non-GRP construction
may require an external GPS mounted above decks.
D11190-1
Internal GPS environment
In addition to general guidelines concerning the location of marine
electronics, there are a number of environmental factors to consider
when installing equipment with an internal GPS antenna.
Location and mounting
43
Typical locations and GPS performance
bulkhead, or the interior of larger vessels may result in a reduced
GPS signal.
• Other constructions. GPS performance may be adversely
affected below decks. Seek professional assistance and consider
use of an external GPS antenna mounted above decks.
Prevailing conditions
The weather and location of the boat can affect the GPS
performance. Typically calm clear conditions provide for a more
accurate GPS fix. Vessels at extreme northerly or southerly latitudes
may also receive a weaker GPS signal. GPS antenna mounted
below decks will be more susceptible to performance issues related
to the prevailing conditions.
Optimal GPS performance (above decks)
GPS performance af
fected by prevailing conditions
Not recommended
D11537-1
Vessel construction
• GRP vessels. Unit can be mounted above and below decks.
Although the proximity of heavy structure such as a structural
44
C-Series Widescreen installation
4.2 Flush mounting
The standard method for mounting a C-Series display is a flush
or panel mounting arrangement.
Before mounting the unit, ensure that you have:
• Selected a suitable location
• Identified the cable connections and route that the cables will take
• Detached the front bezel
D11193-1
1. Check the selected location for the unit. A clear, flat area with
suitable clearance behind the panel, is required.
2. Fix the appropriate cutting template supplied with the product, to
the selected location, using masking or self-adhesive tape.
3. Using a suitable hole saw (the size is indicated on the template),
make a pilot hole in each corner of the cut-out area.
4. Using a suitable saw, cut along the inside edge of the cut-out line.
Location and mounting
45
5. Ensure that the unit fits into the removed area and then file
around the cut edge until smooth.
6. Drill four 4.5 mm (3/16 in) holes as indicated on the template
to accept the securing bolts.
7. Place the gasket onto the display unit and press firmly onto the
flange.
8. Connect the power, data and other cables to the unit.
9. Slide the unit into place and secure using bolts provided.
Once you have secured the display in place, proceed and attach
the front bezel.
4.3 Bracket (trunnion) mounting
The C-Series widescreen display can be mounted on an optional
bracket.
REQUIRES THE OPTIONAL MOUNTING BRACKET ACCESSORY.
Before mounting the unit ensure that you have:
• Selected a suitable location
• Identified the cable connections and route that the cables will take
• Attached the front bezel
Fixing bolts
When flush mounting your display it is important to use bolts of
an appropriate length. The length used is dependant upon the
thickness of the mounting surface.
Thickness (mm)
Bolt length (mm)
<3
12
3–7
16
7–11
20
11–15
24
15–19
28
19–23
32
46
C-Series Widescreen installation
Note: Bracket (trunnion) mounting kit is available as an optional
accessory.
1. Mark the location of the mounting bracket screw holes on the
chosen mounting surface.
2. Drill pilot holes for the screws using a suitable drill, taking care
that there are no cables or anything that may be damaged
behind the surface.
3. Use the screws supplied to attach the mounting bracket securely.
4. Fit the trim ring to the rear of the display using the M4 bolts
supplied.
5. Attach the display unit to the mounting bracket.
Once you have secured the display in place, proceed and make
the required cable connections.
D11191-1
Location and mounting
47
4.4 Front bezel
Clip recess
Attaching the front bezel
Before fitting the bezel you must have mounted the unit in its
required location.
1. Carefully lift one edge of the screen protection film, so that it is
accessible for removing when unit installation is complete.
2. Place the bezel over the front of the C-Series Display, ensuring
that locking lugs located at the bottom edge of the bezel are
latched into position.
D11196-1
3. Ensure that the control buttons pass through their respective
openings.
4. Apply firm but even pressure to the bezel along the:
i. Outer edges - work from the sides upwards and then along
the top edge, to ensure that it clips securely into position.
ii. Inner edges - particularly along the chart card door edge, to
ensure that the bezel sits flat.
48
C-Series Widescreen installation
5. Check that all control buttons are free to operate. It is suggested
that you use your thumb or forefinger in a circular motion to do
this.
Removing the front bezel
D11197-1
1. When removing the bezel, start at the bottom-middle and work
around to the sides and top edge.
Location and mounting
49
50
C-Series Widescreen installation
Chapter 5: System checks
Chapter contents
•
5.1 Initial power on test on page 52
•
5.2 GPS check on page 53
•
5.3 Radar check on page 54
•
5.4 Sonar check on page 56
•
5.5 Language selection on page 57
System checks
51
5.1 Initial power on test
Note: You can change the required page set at any time during
normal operation.
UniControl
Selecting a page set
The UniControl provides a number of key functions in a single
control.
To select a page set at first time power on:
1. Use the UniControl to select the required set of pages.
1
2
3
1. Rotary Control. Use this to select menu options and adjust the
value of various items.
2. Trackpad. Use this to select menu items, options and move
the cursor.
3. OK button. Use this to confirm a selection or entry.
Powering the display on
1. Press and hold the POWER button until the Raymarine logo
appears.
2. Press OK to acknowledge the warning window.
2. Press OK.
Select a page set
When you first turn the display on you will be prompted to select a
page set from those available.
52
C-Series Widescreen installation
5.2 GPS check
Note: A solid circle on the chart indicates that neither heading
nor Course Over Ground (COG) data is available.
Checking GPS operation
You can check that the GPS is functioning correctly using the chart
application.
1. Press the PAGE button to show the available pages in the
toolbar.
2. Press the PAGE button to switch between the available pages.
3. Press OK when the chart is displayed.
4. Check the screen.
With the chart displayed, you should see:
Your boat position (indicates a GPS fix). Your current position
is represented by a boat symbol or solid circle. Your position is
also displayed in the data bar under VES POS.
System checks
53
5.3 Radar check
Typical HD digital radar screen
Warning: Radar scanner safety
Before rotating the radar scanner, ensure all personnel
are clear.
Warning: Radar transmission safety
The radar scanner transmits electromagnetic energy.
Ensure all personnel are clear of the scanner when
the radar is transmitting.
Checking the radar
1. Select a Radar page:
• Press the PAGE button to select from the current page set.
• Press and hold the PAGE button to select from all available
pages.
The Radar scanners will now initialize in standby mode, this
process will take approximately 70 seconds.
2. Press the POWER button.
3. Press the Radar Tx/Stdby softkey and set to Tx.
The scanners should now be transmitting and receiving.
4. Check that the radar screen is operating correctly.
54
Note: Analog and non-HD radar screens will have different
coloring / appearance.
Points to check:
• Radar sweep with echo responses are shown on screen.
• Radar status icon rotating in top right hand corner.
Check and adjust bearing alignment
Bearing alignment
The radar bearing alignment ensures that radar objects appear at
the correct bearing relative to your boat’s bow. You should check
the bearing alignment for any new installation.
C-Series Widescreen installation
Example misaligned radar
2. Note the position of the object on the radar display. If the target
is not under the ships heading marker (SHM), there is an
alignment error and you will need to carry out bearing alignment
adjustment.
Adjusting the bearing alignment
Once you have checked the bearing alignment you can proceed and
make any required adjustments.
With the radar page displayed:
1. Select the bearing alignment menu.
2. Press the BEARING ALIGNMENT softkey.
3. Use the rotary control to place the selected target under the
Ship’s Heading Marker.
4. Press OK when complete.
Adjusting radar offset (parking)
This setting is applicable to open array scanners. It is used to
ensure the scanner parks in the correct position when rotation stops.
Before you proceed, ensure that:
• The radar page is selected
• The radar scanner is initialized standby mode
Target object dead ahead
(bearing alignment will be required)
Radar target not aligned
D11590-1
Checking the bearing alignment
1. With your vessel under way: Align the bow with a stationary
object identified on the radar display An object between 1 & 2
NM distant is ideal.
System checks
1. Press the MENU button and then select the radar setup menu
(with the radar in standby mode).
2. Select the PARKING OFFSET option, then adjust the offset
angle required to park the radar so that the antenna comes to
rest facing forward (you should see the Raymarine logo wording
from the front of the vessel) when you place it in either standby
or switch it off.
3. Press OK when complete.
55
5.4 Sonar check
3. Press OK when the fishfinder is displayed.
Warning: Sonar operation
• NEVER operate the sounder with the boat out of
the water.
• NEVER touch the transducer face when the sounder
is powered on.
• SWITCH OFF the sounder if divers are likely to be
within 25 ft (5 m) of the transducer.
Select the fishfinder transducer
You must set the set up the system for the transducer connected to
your DSM. Use the fishfinder setup menus to select the appropriate
transducer.
Selecting the fishfinder transducer
From the main fishfinder screen:
1.
2.
3.
4.
Press the MENU button.
Select Fishfinder Setup from the list of options.
Select Transducer Settings from the list of menu options:
Use the Select Transducer option and select the appropriate
transducer from those available.
4. Check the fishfinder screen.
With the fishfinder active you should see:
• Depth reading (indicates the transducer is working). The
depth is shown in large white numbers at the bottom left of
the screen.
Checking the sonar
Sonar checks are made using the fishfinder application.
1. Press the PAGE button to show the available pages in the
toolbar.
2. Press the PAGE button to switch between the available pages.
56
C-Series Widescreen installation
5.5 Language selection
The C-Series multifunction display can operate in the following
languages:
English (US)
English (UK)
Chinese
Danish
Dutch
Finnish
French
German
Greek
Icelandic
Italian
Japanese
Korean
Norwegian
Portuguese
Russian
Spanish
Swedish
1.
2.
3.
4.
5.
6.
7.
Press the MENU button to open the setup menu.
Use the trackpad up / down to select the System Setup menu.
Use the trackpad right to open the sub-menu.
Use the trackpad to select the Language options.
Select from the languages available.
Press OK to accept and save the change.
Press OK again to return back through the menus to the normal
display.
System checks
57
58
C-Series Widescreen installation
Chapter 6: Troubleshooting
Chapter contents
•
6.1 Troubleshooting on page 60
•
6.2 Power up troubleshooting on page 60
•
6.3 Radar troubleshooting on page 61
•
6.4 GPS troubleshooting on page 62
•
6.5 Sonar troubleshooting on page 63
•
6.6 System data troubleshooting on page 64
•
6.7 SeaTalkhs LED indications on page 65
•
6.8 Miscellaneous troubleshooting on page 66
Troubleshooting
59
6.1 Troubleshooting
6.2 Power up troubleshooting
The troubleshooting information provides possible causes and
corrective action required for common problems associated with
marine electronics installations.
Problems at power up and their possible causes and solutions are
described here.
All Raymarine products are, prior to packing and shipping, subjected
to comprehensive test and quality assurance programs. However,
if you experience problems with the operation of your C-Series
multifunction display, this section will help you to diagnose and
correct problems in order to restore normal operation.
If after referring to this section you are still having problems with your
unit, please contact Raymarine Technical Support for further advice.
Problem
Possible causes
Possible solutions
The display does not
start up.
Problem with power to
the unit.
Check relevant fuses
and breakers.
Check that the power
supply cable is sound
and that all connections
are tight and free from
corrosion.
Check that the power
source is of the correct
voltage and sufficient
current.
60
C-Series Widescreen installation
6.3 Radar troubleshooting
Problem
Possible causes
Possible solutions
Problems with the radar and their possible causes and solutions
are described here.
No Data or No scanner
message.
Radar scanner power
supply.
Check that the scanner
power supply cable
is sound and that all
connections are tight
and free from corrosion.
Check relevant fuses
and breakers.
Check power source is
of the correct voltage
and sufficient current
(using voltage booster if
appropriate).
SeaTalkhs network
problem.
Check that the Scanner
is correctly connected
to the display via a
cross over coupler or
SeaTalkhs switch.
Check the status of the
SeaTalkhs Switch.
Check that SeaTalkhs
cables are free from
damage.
Troubleshooting
Software mismatch
between equipment may
prevent communication.
Contact Raymarine
technical support.
Switch at scanner
pedestal in OFF position.
Ensure scanner
pedestal switch is in
ON position.
61
Problem
Possible causes
Possible solutions
6.4 GPS troubleshooting
The bearing of a target
on the radar screen is
incorrect.
The radar bearing
alignment requires
correcting.
Check and adjust radar
bearing alignment.
Problems with the GPS and their possible causes and solutions
are described here.
Problem
Possible causes
Possible solutions
“No Fix” GPS status
icon is displayed.
Geographic location or
prevailing conditions
preventing satellite fix.
Check periodically to
see if a fix is obtained
in better conditions or
another geographic
location.
External GPS antenna
conflict with internal
GPS.
Disable internal GPS
from within the setup
menus.
Internal GPS antenna
has been disabled.
Enable internal GPS
from within the setup
menus.
External GPS
connection fault.
Ensure that GPS
connections and cabling
are correct and fault
free..
Unit mounted in poor
location.
For example:
Ensure that the unit is
mounted in accordance
with the instructions.
• Below decks on Steel
construction vessel.
• Close proximity
to transmitting
equipment such as
VHF radio.
External GPS antenna in
62
Ensure GPS antenna
C-Series Widescreen installation
poor position.
has a clear view of the
sky.
GPS installation
problem.
Refer to manufacturers
handbook for installation
details.
Note: A GPS Status screen is available within the Setup
menu. This provides satellite signal strength and other relevant
information.
6.5 Sonar troubleshooting
Problems with the sonar and their possible causes and solutions
are described here.
Problem
Possible causes
Possible solutions
No data source for the
fishfinder.
DSM power supply fault.
Check the DSM power
supply and cables.
Other DSM fault.
Refer to the instructions
supplied with the DSM
unit.
SeaTalkhs network
problem.
Check that the DSM is
correctly connected to
the display or SeaTalkhs
switch.
Check the status of the
SeaTalkhs Switch.
Check that SeaTalkhs
cables are free from
damage.
Software mismatch
between equipment may
prevent communication.
Troubleshooting
Contact Raymarine
technical support.
63
Problem
Possible causes
Possible solutions
6.6 System data troubleshooting
Problematic depth
readings or sonar
image.
Gain or Frequency
settings may be
inappropriate for present
conditions.
Check the fishfinder
presets, gain and
frequency settings.
Aspects of the installation can cause problems with the data shared
between connected equipment. Such problems, their possible
causes and solutions are described here.
DSM cable fault.
Ensure that the power,
transducer and all other
cables to the DSM unit
are properly connected
and free from damage.
Other DSM fault.
Problem
Possible causes
Possible solutions
Instrument, engine
or other system data
is unavailable at all
displays.
Data is not being
received at the display.
Check the data bus
(e.g. SeaTalkng) wiring
and connection to the
display.
Refer to the instructions
supplied with the DSM
unit.
Check the overall
integrity of the data
bus (e.g. SeaTalkng)
wiring.
If available refer to
the reference guide
for the data bus. (e.g.
SeaTalkng reference
manual)
Data source (e.g
ST70 instrument or
engine interface) is not
operating.
Check the source of the
missing data (e.g. ST70
instrument or engine
interface).
Check the power to the
SeaTalk bus.
Refer to the
manufacturer’s
handbook for the
equipment in question.
Software mismatch
between equipment may
prevent communication.
64
Contact Raymarine
technical support.
C-Series Widescreen installation
Instrument or other
system data is missing
from some but not all
displays.
SeaTalkhs network
problem
Check that all required
equipment is connected
to the SeaTalkhs switch.
Check the status of the
SeaTalkhs Switch.
Software mismatch
between equipment may
prevent communication.
6.7 SeaTalkhs LED indications
LED indications associated with the SeaTalkhs switch are described
here.
LED state
Possible causes
Check that SeaTalkhs
cables are free from
damage.
For all connected channels: 1 steady
and 1 flashing green LED.
No problem detected (Steady LED
indicates network connection Flashing
LED indicates network traffic) .
Contact Raymarine
technical support
No LEDs are illuminated.
No power to the SeaTalkhs switch.
Some LEDs are not illuminated.
• Cable / connection faults on the
channels with non-illuminated
LEDs.
• Equipment connected to
non-illuminated LEDs may be
faulty.
Troubleshooting
65
6.8 Miscellaneous troubleshooting
Miscellaneous problems and their possible causes and solutions
are described here.
Problem
Possible causes
Possible solutions
Display behaves
erratically:
Intermittent problem with
power to the display.
Check relevant fuses
and breakers.
Check that the power
supply cable is sound
and that all connections
are tight and free from
corrosion.
• Frequent unexpected
resets.
• System crashes or
other erratic behavior.
Problem
Possible causes
Possible solutions
Important: This
will result in the
loss of any settings
and data (such as
waypoints) stored on
the display. Please
save any important
data to a CF card
before resetting.
Check that the power
source is of the correct
voltage and sufficient
current.
66
Buttons trapped by front
bezel.
Ensure that the front
bezel is fitted correctly
and that all buttons are
free to operate correctly.
Software mismatch
on system (upgrade
required).
Go to
www.raymarine.com
and click on support
for the latest software
downloads.
Corrupt data / other
unknown issue.
Perform a factory reset.
This option can be found
within Menu > System
Setup > Settings and
Data Reset .
C-Series Widescreen installation
Troubleshooting
67
68
C-Series Widescreen installation
Chapter 7: Technical support
Chapter contents
•
7.1 Raymarine technical support on page 70
•
7.2 Sirius support on page 70
•
7.3 Navionics support on page 71
Technical support
69
7.1 Raymarine technical support
7.2 Sirius support
Web support
Sirius marine weather
Please visit the customer support area of our website at:
www.sirius.com/marineweather
www.raymarine.com
This contains Frequently Asked Questions, servicing information,
e-mail access to the Raymarine Technical Support Department and
details of worldwide Raymarine agents.
Sirius audio
www.sirius.com
Telephone support
In the USA call:
+1 603 881 5200 extension 2444
In the UK, Europe, the Middle East, or Far East call:
+44 (0)23 9271 4713
Product information
If you need to request service, please have the following information
to hand:
• Product name.
• Product identity.
• Serial number.
• Software application version.
You can obtain this product information using the menus within your
product.
Viewing product information
1.
2.
3.
4.
70
Open the system Setup menu.
Select System Diagnostics.
Select Software Services.
Select the Software Services menu:
C-Series Widescreen installation
7.3 Navionics support
Navionics website
www.navionics.com
Technical support
71
72
C-Series Widescreen installation
Chapter 8: Technical specification
Chapter contents
•
8.1 Technical specification on page 74
Technical specification
73
8.1 Technical specification
Nominal supply voltage
12 or 24 V dc
Operating voltage range
10.7 to 32 V dc
Fuse / Breakers
In-line fuse (fitted within power cable)
Weight
• C90W: 3.8 kg (8.5 lb)
• C120W: 4.8 kg (10.5 lb)
• C140W: 5.6 kg (12.3 lb)
Display screen
• 7 A. (Standard 20 mm glass fuse)
TFT LCD display, 24bit color (16.7 M
colors)
• C90W: 9 in display, 800 x 480 pixels
• C120W: 12 in display, 1280 x 800
pixels
• C140W: 14 in display, 1280 x 800
pixels
Data connections.
3 x NMEA 0183 ports:
Current
4 A max operating current
Power consumption
32 W typical power consumption
• NMEA port 1: I/O 4800/9600 baud.
Environmental
Installation environment
• NMEA port 2: I/O 4800/9600/38400
baud.
• Operating temperature: –10 ºC to
50 º (14 ºF to 122 ºF
• Non-operating temperature:
—20 ºC to 70 ºC (-4 ºF to 158 ºF)
• Relative humidity: max 95%
• Water proof to IPX6
• NMEA port 3: Input only, 4800
baud.
1 x SeaTalk port.
2 x SeaTalkhs RJ45 type connections
• 10/100 Mbits/S
1 x SeaTalkng connection
Storage conditions (when packed):
• Temperature: —25 ºC to 55 ºC
(-13 ºF to 158 ºF)
• Relative humidity: max 75%
74
C-Series Widescreen installation
GPS
• 12 channel receiver
Cartography
Navionics embedded cartography
appropriate to purchase region. (North
America, Europe or Rest of World, as
appropriate)
Conformance
• Europe: R&TTE 1999/5/EC
• Sirf star chipset for high sensitivity
and rapid fix
• Frequency of operation: 1575.43
Mhz +/- 1Mhz (C/A code), L1
• Sensitivity: –159dBm (tracking),
–142dBm acquisition·
• Australia and New Zealand: C-Tick,
Compliance Level 2
• Signal Acquisition: Automatic
• Cold Start 35 seconds to 2.5
minutes under good signal
conditions
• SBAS: WAAS/EGNOS compatible
• Almanac update: Automatic
• Horizontal Positional Accuracy:
<=15 metre @ 95% of time (without
SA), <=5metres @ 95% with
WAAS/EGNOS
• Geodetic Datum: WGS-84
(alternatives available through
Raymarine display)
• Update rate: Once a second
• Helical antenna for even antenna
gain across most display
orientations
• GPS data bridged to NMEA 0183,
SeaTalk and SeaTalkng outputs.
Technical specification
75
76
C-Series Widescreen installation
Chapter 9: Options and accessories
Chapter contents
•
9.1 SeaTalk accessories on page 78
•
9.2 SeaTalkng accessories on page 78
•
9.3 SeaTalkhs accessories on page 79
•
9.4 Spares and accessories on page 81
Options and accessories
77
9.1 SeaTalk accessories
9.2 SeaTalkng accessories
SeaTalk cables and accessories for use with compatible products.
SeaTalkng cables and accessories for use with compatible products.
Description
Part No
NMEA / SeaTalk
converter
E85001
3 m (9.8 ft) SeaTalk
extension cable
D285
• 2 x 5 m (16.4 ft)
Backbone cable
5 m (16.4 ft) SeaTalk
extension cable
D286
•
9 m (29.5 ft) SeaTalk
extension cable
D287
• 4 x T-piece
12 m (39.4 ft) SeaTalk
extension cable
E25051
20 m (65.6 ft) SeaTalk
extension cable
D288
78
Notes
Description
Part No
Notes
Backbone Kit
A25062
Includes:
•
1 x 20 m (65.6 ft)
Backbone cable
2 x Backbone
terminator
• 1 x Power cable
SeaTalkng 0.4 m (1.3 ft)
spur
A06038
SeaTalkng 1 m (3.3 ft)
spur
A06039
SeaTalkng 3 m (9.8 ft)
spur
A06040
SeaTalkng 5 m (16.4 ft)
spur
A06041
SeaTalkng 0.4 m (1.3 ft)
backbone
A06033
SeaTalkng 1 m (3.3 ft)
backbone
A06034
C-Series Widescreen installation
9.3 SeaTalkhs accessories
Description
Part No
SeaTalkng
A06035
3 m (9.8 ft)
backbone
Notes
Digital radar scanner cables
Scanner cables
SeaTalkng 5 m (16.4 ft)
backbone
A06036
SeaTalkng 20 m (65.6 ft)
backbone
A06037
SeaTalkng - bare ends 1
m (3.3 ft) spur
A06043
SeaTalkng - bare ends 3
m (9.8 ft) spur
A06044
SeaTalkng — SeaTalk2
0.4 m (1.3 ft) spur
Connect the Radar scanner to either the SeaTalkhs switch or the cross over coupler.
Cable
Part number
5 m (16.4 ft) Digital cable
A55076
10 m (32.8 ft) Digital
cable
A55077
A06048
15 m (49.2 ft) Digital
cable
A55078
SeaTalkng Power cable
A06049
25 m (82.0 ft) Digital
cable
A55079
SeaTalkng Terminator
A06031
SeaTalkng T-Piece
A06028
Scanner extension cables
SeaTalkng E-Piece
A06064
Use of one of these cables to extend the connection between the radar scanner
and the SeaTalkhs switch or cross over coupler.
SeaTalkng Blanking plug
A06032
Options and accessories
Cable
Part number
2.5 m (8.2 ft) extension
cable
A92141
5 m (16.4 ft) extension
cable
A55080
10 m (32.8 ft) extension
cable
A55081
Notes
Your radar scanner may
include the 10 m cable
(depending upon the
model purchased)
Notes
79
SeaTalkhs network cables
SeaTalkhs hardware
Cable
SeaTalkhs network cables
SeaTalkhs
Standard network cables connect compatible equipment to the
cross over coupler), they have a waterproof connector at one end.
Cable
Part number
1.5 m (4.9 ft) SeaTalkhs
network cable
E55049
5 m (16.4 ft) SeaTalkhs
network cable
E55050
10 m (32.8 ft) SeaTalkhs
network cable
E55051
20 m (65.6 ft) SeaTalkhs
network cable
E55052
switch (or
Notes
SeaTalkhs
switch
SeaTalkhs coupler
Part number
Notes
E55058
8 way hub for network
connection of multiple
SeaTalkhs devices.
E55060
Couple for connection
of a single SeaTalkhs
device.
Fully waterproof SeaTalkhs network cables
Connect directly from display to display.
Cable
Part number
Notes
1.5 m (4.9 ft) Dual end
SeaTalkhs network cable.
A62245
Cable has waterproof
connectors at both ends.
15 m (49.2 ft) Dual end
SeaTalkhs network cable
A62246
Cable has waterproof
connectors at both ends.
80
C-Series Widescreen installation
9.4 Spares and accessories
Options and accessories for the C-Series Widescreen Multifunction
displays.
Optional accessories
Notes
Description
Part No
1.5 m (4.9 ft) Power and
data cable — straight
R62131
1.5 m (4.9 ft) Power and
data cable — 90 degree
R62227
SeaTalkhs dust cap
R62228
SeaTalkng
R62229
Description
Part No
Trunnion (bracket)
mount kit (C190W)
A62132
Trunnion (bracket)
mount kit (C120W)
A62133
Service spares
Trunnion (bracket)
mount kit (C140W)
A62134
Description
Part No
Chart door
R62184
Rotary Trackpad
R62185
Seal Set (C90W)
R62186
Seal Set (C120W)
R62187
Seal Set (C140W)
R62188
Keymat set
R62189
Keycap set
R62190
Spare / replacement parts
Description
Part No
Flush mount kit (C90W)
R62125
Flush mount kit (C120W)
R62126
Flush mount kit (C140W)
R62127
Trunnion knob
R08001
Suncover (C90W)
R62122
Front panel (C90W)
R62191
Suncover (C120W)
R62123
Front panel (C120W)
R62192
Suncover (C140W)
R62124
Front panel (C140W)
R62193
Bonded LCD Assembly
(C90W)
R62199
Options and accessories
Notes
dust cap
Notes
Notes
81
Description
Part No
Bonded LCD Assembly
(C120W)
R62200
Bonded LCD Assembly
(C140W)
R62206
Chartreader assembly
Description
Part No
I/O PCB assy
R62222
CPU pcb assy
R62223
CPU-IO cable assy
R62224
R62209
EMC pad
R62225
Chartreader cable
assembly
R62210
Heat pad set
R62226
Lower keyboard assy
(C90W)
R62211
Lower keyboard assy
(C120W)
R62212
Lower keyboard assy
(C140W)
R62213
Side keyboard assy
R62214
Rotary keyboard assy
R62215
Keyboard cable assy
R62216
GPS assembly (C90W)
R62217
GPS assembly (C120W)
R62218
GPS assembly (C140W)
R62218
GPS cable assy
R62219
LVDS cable assy
R62221
CCFL cable assy
(C140W Only)
R62220
82
Notes
Notes
C-Series Widescreen installation
Appendix A Connectors and pinouts
Power, data and video connector
Signal
Pin
Cable
AWG
SCREEN
17
not used
NMEA1
TX+
6
7/0.15
26
NMEA1
TX-
9
7/0.15
26
NMEA1
RX+
4
7/0.15
26
NMEA1
RX-
8
7/0.15
26
Grouping
Color
1
2
3
5
4
6
8
7
9
11
18
10
19
12
13
14
15
16
17
Twisted
pair
Yello
Brown
Twisted
pair
White
Item
Remarks
Identification
PWR/NMEA/ST/Video
Connector type
19 pin twist-lock
NMEA2
TX+
1
7/0.15
26
Current source to network
No current sourced for external
devices.
NMEA2
TX-
3
7/0.15
26
Current sink from network
• PSU: Main Power input.
NMEA2
RX+
7
7/0.15
26
NMEA2
RX-
11
7/0.15
26
• ST1: <50mA (Interface drive only).
• Video: No power required for
interface.
NMEA3
RX+
5
7/0.15
26
NMEA3
RX-
2
7/0.15
26
Blue /
Green
Color
ST1
BATT+
10
7/0.15
26
White /
Red
ST1 DATA
12
7/0.15
26
White /
Yellow
• NMEA: No power required for
interface.
Power, data and video cable cores and colors
Grouping
Signal
Pin
Cable
AWG
BATT+
18
32/0.2
18
Red
BATT-
19
32/0.2
18
Black
Connectors and pinouts
Green
Twisted
pair
Orange /
Yellow
Orange /
Brown
Twisted
pair
Orange /
White
Orange /
Green
Twisted
pair
Blue /
White
83
Grouping
Signal
Pin
Cable
AWG
HONK
16
7/0.15
26
Grey
ST1
BATT-
14
7/0.15
26
White /
Black
VIDEO
15
RG179
75R coax
(or equivalent)
13
VIDEO
RTN
Color
Screen
Pin
Signal
1
+12V
2
0V
3
Screen
4
CanH
5
CanL
6
SeaTalk (not connected)
Note: Use only Raymarine cables when connecting to SeaTalkng
SeaTalkhs connector
SeaTalkng connector
1
5
8
1
6
4
2
3
Item
Remarks
Item
Remarks
Identification
ST2/NMEA2000
Identification
STHS
Connector type
STNG
Connector type
RJ45 (with suitable waterproofing)
Current source to network
No current sourced for external devices
Current source to network
No current sourced for external devices
Current sink from network
<160mA (Interface drive only)
Current sink from network
No power required for interface
84
C-Series Widescreen installation
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
4
Not connected
5
Not connected
6
Rx-
7
8
The C-Series Widescreen display supports the following NMEA
0183 sentences. These are applicable to NMEA 0183 and SeaTalk
protocols.
Transmit
APB
Autopilot b
BWC
Bearing and distance to waypoint
Not connected
BWR
Bearing and distance to waypoint
rhumb line
Not connected
DBT
Depth below transducer
DPT
Depth
MTW
Water temperature
RMB
Recommended minimum navigation
information
RSD
Radar system data
TTM
Tracked target message
VHW
Water speed and heading
VLW
Distance travelled through the water
GGA
Global positioning system fix data
GLL
Geographic position latitude longitude
GSA
GPS DOP and active satellites
GSV
GPS satellites in view
RMA
Recommended minimum specific
loran c data
Note: Use only Raymarine cables when connecting to SeaTalkhs
NMEA 0183 sentences
Appendix B NMEA 0183 sentences
85
RMC
Recommended minimum specific
GPS transit data
VTG
Course over ground and ground speed
Geographic position loran c sentence
GLC
GLL
Geographic position latitude longitude
sentence
ZDA
Time and date
MWV
Wind speed and angle
GSA
GPS DOP and active satellites
sentence
RTE
Routes sentence
GSV
GPS satellites in view sentence
WPL
Waypoint location sentence
HDG
Heading deviation and variation
sentence
HDT
Heading true sentence
HDM
Heading magnetic sentence
MSK
MSK receiver interface sentence
MSS
MSK receive r signal status sentence
MTW
Water temperature sentence
Receive
AAM
Waypoint arrival alarm sentence
DBT
Depth below transducer sentence
DPT
Depth sentence
DTM
Datum reference sentence
APB
Autopilot b sentence
WMV
Wind speed and angle sentence
BWC
Bearing and distance to waypoint
sentence
RMA
Recommended minimum specific
loran c data sentence
BWR
Bearing and distance to waypoint
rhumb line sentence
RMB
Recommended minimum navigation
information sentence
DSC
Digital selective calling information
sentence
RMC
Recommended minimum specific
GPS transit data sentence
DSE
Distress sentence expansion
VHW
Water speed and heading sentence
GGA
Global positioning system fix data
sentence
VLW
Distance travelled through the water
sentence
VTG
Course over ground and ground speed
sentence
86
C-Series Widescreen installation
Appendix C NMEA 2000 sentences
XTE
Cross track error measured sentence
ZDA
Time and date sentence
MDA
Meteorological composite sentence
The C-Series Widescreen display supports the following NMEA
2000 sentences. These are applicable to NMEA 2000, SeaTalkng
and SeaTalk 2 protocols.
GBS
GPS satellite fault detection data
sentence
Transmit
RTE
Routes sentence
128267
Water depth
WPL
Waypoint location sentence
129283
Cross track error
129291
Set and drift rapid update
129301
Time to mark
130578
Vessel speed components
129026
COG SOG rapid update
130577
Direction data
129550
GNSS differential correction receiver
interface
129551
GNSS differential correction receiver
signal
129029
GNSS position data
129540
GNSS sats in view
129284
Navigation data
129025
Position rapid update
128275
Distance log
128259
Speed
127237
Heading track control
NMEA 2000 sentences
87
127245
Rudder
129539
NMEA 2000 GNSS DOPs message
127250
Vessel heading
129029
GNSS position data
126992
System time
129545
NMEA 2000 GNSS RAIM output
message
129540
GNSS Sats in view
127237
Heading / track control
129284
Navigation data
129025
Position rapid update
127245
Rudder
129291
Set and drift rapid update
128259
Speed
126992
System time
129033
Time and date
129301
Time to or from mark
127250
Vessel heading
130578
Vessel speed components
128267
Water depth
130306
Wind data
130576
Small craft status
127489
Dynamic engine parameters
127488
Engine parameters rapid update
127493
Dynamic transmission
129033
Time and date
130310
Environmental parameters
130306
Wind data
129044
Datum
126464
Pgn list
126996
Product information
Receive
129026
NMEA 2000 COG and SOG rapid
update message
129283
NMEA 2000 cross track error message
129044
NMEA 2000 datum message
130577
NMEA 2000 direction data message
128275
NMEA 2000 distance log message
130310
NMEA 2000 environmental
parameters message
130311
NMEA 2000 environmental
parameters message
129550
NMEA 2000 GNSS differential
correction receiver interface message
129551
NMEA 2000 GNSS differential
correction receiver signal message
88
C-Series Widescreen installation
127505
Fluid level
127498
Static engine parameters
126464
PGN List
126996
Product information
NMEA 2000 sentences
89
90
C-Series Widescreen installation
Raymarine plc
AnchoragePark, Portsmouth,
HampshirePO3 5TD,
United Kingdom.
Raymarine Inc.
21 Manchester Street, Merrimack,
New Hampshire03054-4801,
USA.
Tel:+44 (0) 23 9269 3611
Fax: +44 (0) 23 9269 4642
www.raymarine.com
Tel:+1 603.881.5200
Fax: +1 603.864.4756
www.raymarine.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement