Craftsman | 315.113980 | Operator`s manual | Craftsman 315.113980 Operator`s manual

PERATOR'S
MAN
AL
T$
4 V LITHIUM-ION
SCREWDRIVER
TWO SPEED/REVERSIBLE
Model No.
315.113980
A
WARNING:
To reduce the risk of injury,
the user must read and understand the
operator's manual before using this
product.
Craftsman
Consumer
Sears, Roebuck
Helpline:
1-800-932-3188
and Co., 3333 Beverly Rd., Hoffman
Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
C
987000-181
09-26-07 (REV:01)
Save this manual
for future
reference
•
Warranty ..........................................................................................................................................................................
2
•
Introduction .....................................................................................................................................................................
2
•
General Safety Rules ....................................................................................................................................................
•
Specific Safety Rules .......................................................................................................................................................
4
•
Safety Rules for Charger .................................................................................................................................................
5
•
Symbols ........................................................................................................................................................................
•
Features ...........................................................................................................................................................................
8
•
Assembly .........................................................................................................................................................................
9
•
Operation ....................................................................................................................................................................
9-11
•
Maintenance .............................................................................................................................................................
11-12
•
Accessories ...................................................................................................................................................................
13
•
Exploded View and Parts List ........................................................................................................................................
13
•
Parts Ordering/Service
.....................................................................................................................................
ONE-YEAR FULL WARRANTY
ON CRAFTSMAN
3-4
6-7
Back Page
TOOL
If this Craftsman tool fails to give complete satisfaction within one year from date of purchase, RETURN iT TO ANY
SEARS STORE OR OTHER CRAFTSMAN OUTLET iN THE UNITED STATES FOR FREE REPLACEMENT.
If this Craftsman tool is used for commercial
purchase.
or rental purposes, this warranty applies for only 90 days from the date of
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
This product has many features for making its use more pleasant and enjoyable. Safety, performance,
have been given top priority in the design of this product making it easy to maintain and operate.
A
and dependability
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
A
WARNING!
Read all instructions.
Failure to
follow all instructions listed below may result in
electric shock, fire and/or serious injury. The term
"power tool" in all of the warnings listed below
refers to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
SAVE THESE
INSTRUCTIONS
WORK
SAFETY
AREA
[] Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
[] Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
[] Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
ELECTRICAL
SAFETY
[] Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
[] Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
[] Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk
of electric shock.
[] Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
[] When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
[] Use battery
only with charger
MODEL
315.113980
PERSONAL
listed.
CHARGER
7221701
SAFETY
[] Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
[] Use safety equipment. Always wear
Safety equipment such as dust mask,
shoes, hard hat, or hearing protection
priate conditions will reduce personal
eye protection.
non-skid safety
used for approinjuries.
[] Avoid accidental starting. Ensure the switch is in
the off-position before plugging in. Carrying power
tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
[] Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
[] Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
[] Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
[] if devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust-related hazards.
[] Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
[] Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
POWER
TOOL USE AND CARE
[] Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
[] Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
[] Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments,
changing accessories,
or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
[] Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
[] Maintain power tools. Check for misalignment
or
binding of moving parts, breakage of parts, and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
[] Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
[]
Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended could
result in a hazardous situation.
BATTERY
TOOL USE AND
CARE
[] Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack into
power tools that have the switch on invites accidents.
[] Recharge only
manufacturer.
of battery pack
another battery
with the charger specified by the
A charger that is suitable for one type
may create a risk of fire when used with
pack.
[] Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
[] When
other
nails,
make
battery pack is not in use, keep it away from
metal objects like paper clips, coins, keys,
screws, or other small metal objects that can
a connection from one terminal to another.
[] Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will also make exposed metal
parts of the tool "live" and shock the operator.
[] Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
power tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
[] Always wear safety glasses with side shields.
Everyday glasses have only impact resistant lenses.
They are NOT safety glasses. Following this rule will
reduce the risk of eye injury.
[] Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
[] Protect your hearing. Wear hearing protection
during extended periods of operation. Following this
rule will reduce the risk of serious personal injury.
[] Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories.
Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
[] Do not place battery tools or their batteries near
fire or heat. This will reduce the risk of explosion and
possibly injury.
Shorting the battery terminals together may cause
burns or a fire.
[]
Under abusive conditions, liquid may be ejected
from the battery, avoid contact. If contact accidentally occurs, flush with water, if liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
SERVICE
[] Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
_
[]
WARNING! To reduce the risk of injury, user must
read instruction manual.
When servicing a power tool, use only identical
replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance instructions
create a risk of shock or injury.
may
[] Do not crush, drop or damage battery pack. Do
not use a battery pack or charger that has been
dropped or received a sharp blow. A damaged
battery is subject to explosion. Properly dispose of a
dropped or damaged battery immediately.
[] Batteries vent hydrogen gas and can explode in
the presence of a source of ignition, such as a pilot
light. To reduce the risk of serious personal injury,
never use any cordless product in the presence of
open flame. An exploded battery can propel debris and
chemicals. If exposed, flush with water immediately.
[] Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
[] For best results, your battery tool should be
charged in a location where the temperature is
more than 50°F but less than 100°F. To reduce the
risk of serious personal injury, do not store outside or in
vehicles.
[] Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
[] If the power supply cord is damaged, it must be
replaced only by the manufacturer or by an authorized
service center to avoid risk.
_
WARNING!
[]
READ AND UNDERSTAND ALL
a. That pins on plug of extension cord are the same
number, size and shape as those of plug on charger.
[] Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, battery, and product using battery to prevent
misuse of the products and possible injury or damage.
CAUTION:
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere rating
of charger as specified below:
To reduce the risk of electric shock
or damage to the charger and battery, charge only
lithium-ion rechargeable batteries as specifically
designated on your charger. Other types of
batteries may burst, causing personal injury or
damage.
not recommended
50'
100'
Cord Size (AWG)
16
16
16
Do not operate charger with a damaged cord or
plug, which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
serviceman.
[] Do not disassemble charger. Take it to an authorized
serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
[] Do not abuse cord or charger. Never use the cord to
carry the charger. Do not pull the charger cord rather
than the plug when disconnecting from receptacle.
Damage to the cord or charger could occur and create
an electric shock hazard. Replace damaged cords
immediately.
[] Unplug charger from outlet before attempting
any maintenance or cleaning to reduce the risk of
electric shock.
[] Disconnect charger from the power supply when
not in use. This will reduce the risk of electric shock
[] Make sure cord is located so that it will not
be stepped on, tripped over, come in contact
with sharp edges or moving parts or otherwise
subjected to damage or stress. This will reduce the
risk of accidental falls, which could cause injury, and
damage to the cord, which could result in electric
shock.
or damage to the charger if metal items should fall into
the opening. It also will help prevent damage to the
charger during a power surge.
[] Risk of electric shock. Do not touch uninsulated
portion of output connector or uninsulated battery
terminal.
[] Keep cord and charger from heat to prevent
damage to housing or internal parts.
[] Save these instructions.
Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also to prevent misuse of the product and
possible injury.
[] Do not let gasoline, oils, petroleum-based
products,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
PC
25'
[] Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way. Take it to an authorized serviceman for electrical
check to determine if the charger is in good working
order.
or sold
by the battery charger manufacturer
may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
I
Cord Length (Feet)
NOTE: AWG = American Wire Gauge
[]
[] Do not use charger outdoors or expose to wet or
damp conditions. Water entering charger will increase
the risk of electric shock.
[] Use of an attachment
cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
INSTRUCTIONS. Failure to follow all instructions
listed below, may result in electric shock, fire and/or
serious personal injury.
_1_
An extension
NT SAFETY INSTRUCTION
1. SAVE THESE INSTRUCTIONS
2.
3.
This manual contains important safety and operating instructions for battery charger 7221701.
Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and product
using battery.
CAUTION: To reduce the risk of injury, charge only lithium-ion rechargeable batteries. Other types of batteries may
burst, causing personal injury or damage.
5
Someofthefollowingsymbolsmaybeusedonthis product.Pleasestudythemandlearntheirmeaning.Proper
interpretation
ofthesesymbolswillallowyouto operatethe productbetterandsafer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
mz
Hertz
Frequency (cycles per second)
W
Watt
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic
no
No Load Speed
Rotational speed, at no load
[]
Class II Tool
Double-insulated
.../min
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
@
Wet Conditions Alert
Do not expose to rain or use in damp locations.
Read The Operator's Manual
To reduce the risk of injury, user must read and understand
operator's manual before using this product.
Eye Protection
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Safety Alert
Precautions that involve your safety.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Hot Surface
To reduce the risk of injury or damage, avoid contact with any
hot surface.
=.--=.#_
@
O
,&
@
@
@
®
of current
construction
Thefollowingsignalwordsandmeanings
areintendedto explainthe levelsof riskassociatedwiththis product.
SYMBOL
_,
SIGNAL
MEANING
DANGER:
Indicates
imminently
in death oranserious
injury.hazardous situation, which, if not avoided, will result
WARNING:
Indicates
potentially
hazardous situation, which, if not avoided, could result
in
death ora serious
injury.
CAUTION:
Indicates
potentially injury.
hazardous situation, which, if not avoided, may result
in minor ora moderate
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
_11_ WARNING:
Servicing requires extreme care and knowledge and
should be performed only by a qualified service technician. For service we suggest you return the product to
your nearest SEARS PARTS AND REPAIR SERVICE
CENTER for repair. When servicing, use only identical
replacement parts.
,_,
To avoid serious personal injury, do
not attempt to use this product until you read thoroughly and understand completely the operator's
manual. If you do not understand the warnings and
instructions in the operator's manual, do not use this
product. Call the Craftsman Consumer Helpline at
1-800-932-3188 for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear safety
goggles or safety glasses with side shields and, when needed, a full face shield. We recommend
Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
Always use eye protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
PRODUCT
SPECiFiCATiONS
Motor .......................................................................
Switch ..............................................
No Load Speed .................................
4 V, DC
Two Speed/Reversible
200/600 r/min. (RPM)
Clutch ................................................................
Collet .........................................................................
Charger Input .....................................
1/4 in.
120 V, AC only, 60 Hz
Charge Rate .......................................................
9-12 hours
24 Position
TWO-SPEED GEAR
TRAIN (HI&O)
TORQUE
ADJUSTMENT RING
LED
WORKLIGRT
SWITCH
TRIGGER
CHARGER
Fig. 1
KNOW
YOUR SCREWDRIVER
See Figure 1.
The safe use of this product requires an understanding of
the information on the tool and in this operator's manual
as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all
operating features and safety rules.
LED WORKLIGHT
The screwdriver has a built-in LED worklight that illuminates when the switch trigger is depressed. This feature is
convenient when working in close or tight areas where
additional light is needed.
TORQUE
ADJUSTMENT
RiNG
Your screwdriver has a 24 position clutch. The torque
adjustment ring can be turned to select the right amount
of torque for the application.
TWO=SPEED
GEAR TRAIN
The two-speed gear train is designed for drilling or driving
at LO or HI speeds. A slide switch is located on top of
your screwdriver for selecting either LO or HI speed.
UNPACKING
This product has been shipped completely assembled.
[] Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing
list are included.
,t_
WARNING:
If any parts are damaged or missing
do not operate this product until the parts are
replaced. Failure to heed this warning could result in
serious personal injury.
[] Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
WARNING:
Do not attempt to modify this product
or create accessories not recommended for use with
[] Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
this product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
[] If any parts are damaged or missing, please call
1-800-932-3188 for assistance.
PACKING
LIST
Screwdriver
WARNING:
To prevent accidental starting that
could cause serious personal injury, always remove
the battery pack from the product when assembling
parts.
Bit Set
Case
Charger
Operator's Manual
A
A
WARNING:
Do not allow familiarity with products to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
injury.
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating products.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
APPLICATIONS
You may use this product for the purposes listed below:
[] Driving screws with screwdriver
[] Light-duty drilling
bits
CHARGING
THE SCREWDRIVER
See Figure 2.
This tool has been shipped in a low charge condition to
prevent possible problems. Therefore, you should charge
it overnight prior to use. When charging the screwdriver,
a red charge light will illuminate on the charger. This
red charge light will go off when the screwdriver is fully
charged.
NOTE: Batteries will not reach full charge the first time
they are charged. Allow several cycles (driving screws
followed by recharging) for them to become fully charged.
If the charger does not charge the screwdriver under
normal circumstances, return both the screwdriver and
charger to the nearest Sears or other qualified service
center for electrical check.
INPUT
JACK
CHARGERPLUG
Fig. 2
TO INSERT/REMOVE
13-16
BITS
For driving screws into hard wood
See Figure 3.
(LO speed)
17 - 24
The collet on the screwdriver is designed to accept 1/4
in. hex bits. Insert the bit into the collet as far as possible
until the collet locks on to the bit. To remove a bit, pull
the collet forward to unlock the bit, and then pull the bit
straight out of the collet.
PULLCOLLETFORWARDTO
REMOVEBiT
For driving large screws
(LO speed)
DRILLING
AND DRIVING/REMOVING
SCREWS
See Figure 5.
For driving screws or drilling small holes, depress the "up"
arrow on the switch trigger. For removing screws, depress
the "down" arrow on the switch trigger.
_lllilll I::
SWITCH
J
BiT
PUSHTo
Immi_:_J
CLICK
Fig. 5
TWO-SPEED
Fig. 3
The screwdriver has a two-speed gear train designed for
LO or HI speeds. A slide switch is located on top of the
screwdriver to select either LO or HI speed. When using
screwdriver in the LO speed range, speed will decrease
and unit will have more power and torque. When using
screwdriver in the HI speed range, speed will increase and
unit will have less power and torque. When drilling use 1/4
in. hex shank drill bits only. Maximum drill size is 1/4 in.
TORQUE
See Figure 4.
There are twenty-four torque indicator settings located on
the front of the screwdriver.
•
Select the gear train setting to HI or LO speed.
•
Rotate the adjusting ring to the desired setting.
Use the HI speed setting to drill holes, and use the LO
speed setting for driving screws.
•
1- 4
For driving small screws (HI or LO speed)
•
5- 8
For driving screws into soft material
(LO speed)
•
9 - 12
TWO-SPEED
GEARTRAIN(HI&O)
For driving screws into soft and hard
materials (LO speed)
TOINCREASE
TORQUE
GEAR TRAIN
See Figure 6.
ADJUSTABLE
TORQUE CLUTCH
This product is equipped with an adjustable torque clutch
for driving different types of screws into different materials. The proper setting depends on the type of material
and the size of screw you are using.
ADJUSTING
TRIGGER
COLLET
TO DECREASE
TORQUE
ARROW
TORQUE
ADJUSTMENT
RiNG
Fig. 4
Fig. 6
10
LED WORKLIGHT
See Figure 7.
The screwdriver has a built-in LED worklight. This feature
is convenient when working in close or tight areas where
additional light is needed. Whenever the switch trigger is
depressed, the LED worklight will illuminate.
NOTE: During normal operation, if the LED worklight will
not illuminate, charge the screwdriver.
LED
WORKLIGHT
Fig. 7
GENERAL
WARNING: When servicing, use only identical
Craftsman replacement parts. Use of any other part
may create a hazard or cause product damage.
MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
,ik WARNING:
Always wear safety goggles or safety
glasses with side shields when using compressed air
to clean products. If the operation is dusty, also wear
a dust mask.
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc. come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which
may result in serious personal injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
11
BATTERIES
SCREW(S)
This tool is equipped with lithium-ion rechargeable batteries. Length of service from each charging will depend on
the type of work you are doing.
MOTOR
HOUSING
The batteries in this product have been designed to provide maximum trouble-free life. However, like all batteries,
they will eventually wear out. Do not disassemble battery
pack and attempt to replace the batteries. Handling of
these batteries, especially when wearing rings and jewelry,
could result in a serious burn.
To obtain the longest possible battery life, we suggest the
following:
[] Remove the tool from the charger and unplug the
charger once it is fully charged and ready for use.
For tool storage longer than 30 days:
[] Store the tool where the temperature is below 80°R
[] Store the tool in a "discharged" condition.
BATTERY PACK REMOVAL
FOR RECYCLING
AND PREPARATION
See Figure 8.
TO REMOVE:
A
[] Remove the screws securing motor housing cover,
then remove cover.
[] Lift batteries from motor housing enough to expose
leads and battery terminals.
[] Disconnect the red lead from the battery by pulling
apart as shown.
[] Disconnect the black lead from the battery by pulling
apart as shown.
[] Remove the battery for disposal.
This product contains lithium-ion
batteries.
state batteries
or federalproperly.
laws may
I%
recycle
or Local,
dispose
To
preserve
natural ofresources,
please
prohibit disposal of batteries in ordinary
trash.
Consult your local waste authority for information
regarding available recycling and/or disposal options.
12
WARNING: Upon removal, cover the battery pack's
terminals with heaw-duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Lithium-ion
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
Lookfortheseaccessories
atSearsretail:
[] No.2 Phillips/ 8-10 Slotted, 2 Ea.
[]
7-Pc. Screwdriver Bit Set and Case
[]
[]
No. 3 Phillips / 6-8 Slotted, 2 Ea.
5-Pc. Hex Shank Drill Bit Set
[]
13-Pc. Power Screwdriver/Nutdriver
Set and Case
[]
17-Pc. Power Screwdriver/Nutdriver
Set and Case
[]
6-Pc. Extra Length Magnite Power Bit Set
[]
30-Pc. Power Screwdriver/Nutdriver
Set and Case
A
WARNING:
Current attachments and accessories available for use with this product are listed above. Do not use
any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or
accessories not recommended can result in serious personal injury.
_"
CRAFTSMAN
4.0 VOLT SCREWDRIVER
MODEL
NO. 315.113980
J
The
in
allmodel
correspondence
number will regarding
be found on
your
a plate
SCREWDRIVER
attached to the
or when
motor ordering
housing. repair
Alwaysparts.
mention the model number
SEE BACK
PAGE FOR PARTS ORDERING
PARTS
Key
No.
Part
Number
7221701
120790001
580305008
987000181
i
INSTRUCTIONS
LIST
Description
Qty.
Charger ............................................................................................................
Bit Set (Not shown) .........................................................................................
Carrying Case (Not shown) .............................................................................
Operator's Manua(
13
1
1
1
Your Home
For repair-in
your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourse If.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
Call anytime,
® (1-800-469-4663)
day or night(U.S.A,
www.sears.com
and Canada)
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222
Call anytime,
day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655
(U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
1-800-361-6665
(Canada)
Au Canada pour service en fran_;ais:
1-800-LE-FOYER
®
(1-800-533-6937)
www.sears.ca
(1-888-784-6427)
Trademark / T[V ' Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fabrica / SM Marca de Servicio de Sears Brands,
MC Marque de commerce / MDMarque depos6e de Sears Brands, LLC
Mc
® Registered
LLC
© Sears
Brands,
LLC
Download PDF