Roland | KC-150 | Owner`s manual | Roland KC-150 Owner`s manual

Roland KC-150 Owner`s manual
Owner’s Manual
Thank you, and congratulations on your choice of the Roland Keyboard Amplifier KC-150.
These sections provide important information concerning the proper operation of the
unit. Additionally, in order to feel assured that you have gained a good grasp of every
feature provided by your new unit, Owner’s manual should be read in its entirety. The
manual should be saved and kept on hand as a convenient reference.
Before using this unit, carefully read the sections entitled
• IMPORTANT SAFETY INSTRUCTIONS (p. 2)
• USING THE UNIT SAFELY (p. 3–p. 4)
• IMPORTANT NOTES (p. 5).
• Using a Speaker Stand (p. 10)
This unit is equipped with a protection circuit.
The protection circuit helps ensure safety by operating when excessive input continues
for a long time while the device is at a location with a high ambient temperature. Sound
drop-out may occur when the protection circuit is actuated during use.
Please read through the documentation carefully to ensure correct use.
Features
• This monitor-speaker amplifier is designed to provide high-quality sound for a variety
of sources, including digital keyboards and sound modules.
• The two-way monitor features a 30-cm (12-inch) speaker and tweeter, and delivers a
full 65 watts of high-power output.
• The input section features a four-channel mixer. Channel 1 is provided with an XLR
connector in addition to supporting mic input. Channel 4 features a convenient
monitor function that can be used for stage monitoring.
• Features a SUBWOOFER OUT jack, allowing connection of a subwoofer for playback
of even more impressive bass.
• Provided with an RCA phono type AUX IN jack, making it easy to connect devices
such as CD and MD players.
• Master section includes a handy two-band equalizer for adjusting sound quality.
• Provided with a convenient headphones jack for use of the monitor at night.
Copyright © 2003 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any of the ventilation openings. Install in
accordance with the manufacturers instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. When the provided
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Never use with a cart, stand, tripod, bracket,
or table except as specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
For the U.K.
WARNING:
THIS APPARATUS MUST BE EARTHED
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
For EU Countries
This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC.
USING THE UNIT SAFELY
The
symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers
other adverse effects
respect to the home
furnishings, as well
animals or pets.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
to damage or
caused with
and all its
to domestic
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
001
010
• Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
• This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could
cause permanent hearing loss. Do not operate for
a long period of time at a high volume level, or at
a level that is uncomfortable. If you experience
any hearing loss or ringing in the ears, you should
immediately stop using the unit, and consult an
audiologist.
..........................................................................................................
..........................................................................................................
002a
• Do not open or perform any internal modifications on the unit.
..........................................................................................................
003
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” sheet.
..........................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on wet floors);
or are
011
• Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
..........................................................................................................
012a:
• Immediately turn the power off, remove the
power cord from the outlet, and request servicing
by your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page when:
• Humid; or are
• The power-supply cord, or the plug has been
damaged; or
• Exposed to rain; or are
• If smoke or unusual odor occurs
• Dusty; or are
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• Subject to high levels of vibration.
..........................................................................................................
008a
• The unit should be connected to a power supply
only of the type described in the operating instructions, or as marked on the unit.
..........................................................................................................
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally or
exhibits a marked change in performance.
..........................................................................................................
009
• Do not excessively twist or bend the power cord,
nor place heavy objects on it. Doing so can
damage the cord, producing severed elements and
short circuits. Damaged cords are fire and shock
hazards!
..........................................................................................................
3
013
101a
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
..........................................................................................................
• The unit should be located so that its location or
position does not interfere with its proper ventilation.
..........................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
015
• Do not force the unit’s power-supply cord to share
an outlet with an unreasonable number of other
devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
..........................................................................................................
016
• Before using the unit in a foreign country, consult
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
..........................................................................................................
026
• To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture and
objects filled with liquids, such as vases, should
not be placed on this apparatus.
..........................................................................................................
102a
• Always grasp only the plug on the power-supply
cord when plugging into, or unplugging from an
outlet.
..........................................................................................................
103a:
• Any accumulation of dust between the power
plug and the power outlet can result in poor
insulation and lead to fire. Periodically wipe away
such dust with a dry cloth. Also, disconnect the
power plug from the power outlet whenever the
unit is to remain unused for an extended period of
time.
..........................................................................................................
104
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
106
• Never climb on top of, nor place heavy objects on
the unit.
..........................................................................................................
107a
• Never handle the power cord or its plug with wet
hands when plugging into, or unplugging from,
an outlet.
..........................................................................................................
108a
• Before moving the unit, disconnect the power
plug from the outlet, and pull out all cords from
external devices.
..........................................................................................................
109a
• Before cleaning the unit, turn off the power and
unplug the power cord from the outlet.
..........................................................................................................
110a
• Whenever you suspect the possibility of lightning
in your area, pull the plug on the power cord out
of the outlet.
..........................................................................................................
4
IMPORTANT NOTES
291b
In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2,
3 and 4, please read and observe the following:
Power Supply
Maintenance
301
401a
• Do not use this unit on the same power circuit with any device
that will generate line noise (such as an electric motor or variable
lighting system).
• For everyday cleaning wipe the unit with a soft, dry cloth or one
that has been slightly dampened with water. To remove stubborn
dirt, use a cloth impregnated with a mild, non-abrasive detergent.
Afterwards, be sure to wipe the unit thoroughly with a soft, dry
cloth.
307
• Before connecting this unit to other devices, turn off the power to
all units. This will help prevent malfunctions and/or damage to
speakers or other devices.
308
• Although the LEDs are switched off when the POWER switch is
switched off, this does not mean that the unit has been
completely disconnected from the source of power. If you need to
turn off the power completely, first turn off the POWER switch,
then unplug the power cord from the power outlet. For this
reason, the outlet into which you choose to connect the power
cord’s plug should be one that is within easy reach.
Placement
351
• Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum. To
alleviate the problem, change the orientation of this unit; or move
it farther away from the source of interference.
352a
• This device may interfere with radio and television reception. Do
not use this device in the vicinity of such receivers.
352b
402
• Never use benzine, thinners, alcohol or solvents of any kind, to
avoid the possibility of discoloration and/or deformation.
• For routine care of the carpeted surfaces, use a brush with stiff
bristles.
Additional Precautions
553
• Use a reasonable amount of care when using the unit’s buttons,
sliders, or other controls; and when using its jacks and
connectors. Rough handling can lead to malfunctions.
556
• When connecting / disconnecting all cables, grasp the connector
itself—never pull on the cable. This way you will avoid causing
shorts, or damage to the cable’s internal elements.
557
• A small amount of heat will radiate from the unit during normal
operation.
558a
• To avoid disturbing your neighbors, try to keep the unit’s volume
at reasonable levels. You may prefer to use headphones, so you
do not need to be concerned about those around you (especially
when it is late at night).
• Noise may be produced if wireless communications devices, such
as cell phones, are operated in the vicinity of this unit. Such noise
could occur when receiving or initiating a call, or while
conversing. Should you experience such problems, you should
relocate such wireless devices so they are at a greater distance
from this unit, or switch them off.
559a
354b
562
• Do not expose the unit to direct sunlight, place it near devices
that radiate heat, leave it inside an enclosed vehicle, or otherwise
subject it to temperature extremes. Also, do not allow lighting
devices that normally are used while their light source is very
close to the unit (such as a piano light), or powerful spotlights to
shine upon the same area of the unit for extended periods of time.
Excessive heat can deform or discolor the unit.
355b
• When moved from one location to another where the temperature and/or humidity is very different, water droplets (condensation) may form inside the unit. Damage or malfunction may
result if you attempt to use the unit in this condition. Therefore,
before using the unit, you must allow it to stand for several
hours, until the condensation has completely evaporated.
• When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise, you
will need to use equivalent packaging materials.
• Use a cable from Roland to make the connection. If using some
other make of connection cable, please note the following precautions.
• Some connection cables contain resistors. Do not use cables
that incorporate resistors for connecting to this unit. The use
of such cables can cause the sound level to be extremely low,
or impossible to hear. For information on cable specifications,
contact the manufacturer of the cable.
• When transporting and storing the KC-150, be sure to secure the
AC cord to the cord hook on the rear of the main unit.
356
• Do not allow rubber, vinyl, or similar materials to remain on the
unit for long periods of time. Such objects can discolor or
otherwise harmfully affect the finish.
357
• Do not put anything that contains water (e.g., flower vases) on
the unit. Also, avoid the use of insecticides, perfumes, alcohol,
nail polish, spray cans, etc., near the unit. Swiftly wipe away any
liquid that spills on the unit using a dry, soft cloth.
359
• Do not paste stickers, decals, or the like to this instrument. Peeling
such matter off the instrument may damage the exterior finish.
• Do not allow objects to remain on top of the unit while it is in
operation.
5
Panel Descriptions
Control Panel
fig.01
1
2
3
4
5
6
7
8
9
Jack Panel
fig.01
12
11
10
3
2
1
CHANNEL CONTROL
MASTER CONTROL
1. CH 1 knob / CH 1 Input Jacks
These adjust the tone and volume level for the built-in
In addition to a 1/4” phone jack, this channel is equipped with
speakers or for headphones.
a balanced XLR connector, useful for connecting microphones.
This accepts input levels ranging from mic input (-50 dBu) to
line level from sound modules and other equipment (-20 dBu).
4. LOW Knob
This adjusts the level of the bass range.
5. HIGH Knob
2. CH 2 and CH 3 knobs / CH 2 and CH 3
Input Jacks
This adjusts the level of the treble range.
Use these for connecting keyboards, sound modules, and
6. VOLUME Knob
other devices. They accept line level input (-20 dBu).
This adjusts the total volume level of the unit’s internal
3. CH 4 knob / CH 4 Input Jack
speaker. The SUBWOOFER OUT output is also changed.
When connecting headphones, adjust the headphone volume
CH 4 is dedicated to monitoring channel. The signal that is input
level.
to CH 4 will not be output from the line out jack, but will be
* The VOLUME knob do not affect the line outs.
output only from the internal speaker and from the headphones.
You can use the KC-150 for talkback from the main PA or as a
7. PHONES Jack
monitor for live performances on stage or in other locations; this
This is for connecting headphones. The unit’s speakers are
is an easy and convenient way to allow only the performer or
deactivated when headphones are plugged in.
performers to monitor the guide sounds from drum machines.
Also, no signals are output from SUBWOOFER OUT (p. 7).
Use this for connecting keyboards, sound modules, and other
* Always be sure to lower the VOLUME knob to 0 whenever
devices. This accepts line level input (-20 dBu).
* If your setup does not use line output, CH4 can be used in the
same way as the other channels.
6
connecting and disconnecting headphones.
* Although the PHONES jack accepts stereo plugs, the audio
output is mono.
Panel Descriptions
8. Power Indicator
This indicator illuminates when the power is on.
9. POWER Switch
This switches the power on and off.
* Always be sure to lower the volume on the KC-150 and any
connected equipment to 0 whenever turning the power on or off.
* This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will
operate normally.
Slight pop noise may come from the speakers when the power is
switched on, but this does not indicate a problem.
* Refer to p. 9 for the order in which to turn the power to
connected devices on and off.
10.AUX IN Jacks
These are RCA phono type input jacks.
You use these to connect equipment such as CD and MD
players, and have them sound along with the equipment
connected to channel 1 through channel 4.
They accept level input of -10 dBu.
* To adjust the volume level of equipment connected to the AUX
IN jacks, use the controls on such equipment.
* Even though the input signal may be in stereo, the signal is
mixed internally to a mono signal.
11.LINE OUT Jack
Connect mixers, recorders, and other such equipment here.
This output jack provides +4 dBu line level output.
* The MASTER CONTROL knobs (the LOW, HIGH, and
VOLUME controls) do not affect the output from LINE OUT.
The signal that is input to CH 4 will not be output.
12.SUBWOOFER OUT Jack
This lets you play even more powerful bass by connecting a
powered subwoofer.
Provides full-range output, at an output level of +4 dBu.
You can use the MASTER CONTROL knobs (LOW, HIGH,
and VOLUME) to adjust the tone and volume level of the
signals output from SUBWOOFER OUT.
* No signals are output from SUBWOOFER OUT when
headphones are connected.
7
Making the Connections
Refer to the figure shown below to connect the KC-150 and the other equipment.
fig.03
Control Panel
Rear Panel
Stereo
Headphone
Microphone
INPUT
OUTPUT
INPUT
OUTPUT
CD Player
Mixer
Subwoofer
(With built-in amp)
Here is an example of a setup that makes full use of the KC-
Drum Machine
Keyboard
* Howling could be produced depending on the location of
150’s mixer and monitor functions.
microphone relative to speakers. This can be remedied by:
A microphone is input to CH 1, which accepts mic level
1. Changing the orientation of the microphone.
input. Connect a keyboard, recorder, or other sound-
2. Relocating microphone at a greater distance from the speaker.
generating device to the CH 2, CH 3 and CH 4 inputs.
3. Lowering volume levels.
* The signal that is input to CH 4 will not be output from the
line out jack.
* To prevent malfunction and/or damage to speakers or other
of equipment connected to the inputs (CH 1 through CH 4 and
AUX IN) may be low.
devices, always turn down the volume, and turn off the power
If this happens, use connection cables that do not contain
on all devices before making any connections. Set all of the KC-
resistors, such as those from the Roland PCS series.
150’s channel volume knobs as well as the VOLUME knob to
zero.
* The pin assignment for the XLR type connectors is as shown
below. Before making any connections, make sure that this pin
assignment is compatible with that of all your other devices.
fig.04
8
* When connection cables with resistors are used, the volume level
Making the Connections
Switching the Power On and
Off
About the Volume-level
Settings
Once the connections have been completed, turn on power to
In order to get optimum sound from the KC-150 when
your various devices in the order specified. By turning on
performing, set the volume as described below.
devices in the wrong order, you risk causing malfunction
and/or damage to speakers and other devices.
1. Make sure that all volume controls on the KC-150 and
1. Operate the CH 1 through CH 4 volume knobs to adjust
the volume level for channels 1 through 4.
fig.11
connected devices are set to 0.
2. Turn on all the devices connected to the KC-150’s input
jacks (CH 1 through CH 4 and AUX IN).
3. Turn on the KC-150.
4. Switch on any equipment connected to the KC-150’s
LINE OUT or SUBWOOFER OUT jacks.
5. Adjust the volume levels for the devices.
6. Before switching off the power, lower the volume on
each of the devices in your system and then TURN OFF
the devices in the reverse order to which they were
Adjust the volume balance for channels 1 through 4 at this
time.
* To adjust the volume level of equipment connected to the AUX
IN jacks, use the controls on such equipment.
2. Adjust the LOW and HIGH knobs to obtain the tone you
want.
switched on.
* This unit is equipped with a protection circuit. A brief interval
3. Use the VOLUME knob to adjust the overall volume
(a few seconds) after power up is required before the unit will
operate normally. For protection from sudden big sound, always
level.
fig.12
make sure to have the volume level turned down before
switching on power. Even with the volume all the way down,
you may still hear some sound when the power is switched on,
but this is normal, and does not indicate a malfunction.
* If the sound is distorted, lower the CH 1 through CH 4 volume
knobs, VOLUME knob and/or the volume knobs for devices
connected to the input jacks (CH 1 through CH 4 and AUX
IN).
9
Using a Speaker Stand
By using a speaker stand, you can mount the KC-150 at the optimal height for use as a monitor speaker or simple PA device.
fig. Caution
● The KC-150 is designed to be used only with speaker
● Before use, adjust the speaker stand to a height of 140 cm
stands whose dimensions meet the specifications
(55-1/8”) or less and a leg spread of 120 cm (47-1/4”) or
described below.
more, as shown in the figure below.
Do not use it with a speaker stand that does not meet the
fig.08\
following specifications.
fig.05
Diameter: 3.8 cm
(1-1/2”)
140 cm (55-1/8”)
or less
Leg spread: 120 cm (47-1/4”) or more
fig.06_e
120 cm (47-1/4”) or more
● Using a speaker stand that does not meet the
specifications at left or that is adjusted to a height over
Diam
eter:
136 c
m
or mo (53-9/16
”)
re
140 cm (55-1/8”), or a leg spread of less than 120 cm (471/4”) may result in damage to equipment or injury due to
the stand tipping over.
● When using KC-150 with a speaker stand, the speaker
stand must be carefully placed so it is level and sure to
remain stable.
Leg spread: 120 cm (47-1/4”) or more
● When deciding on a stand to use with the KC-150, make
sure to pick one that is capable of supporting its weight.
● Cables connected to KC-150 should be given enough
slack to prevent accidents that might result from someone
tripping over them.
● To prevent accidents due to falls, do not place any object
on the KC-150 when it’s mounted on a speaker stand.
● Always have at least one other person assist you when
mounting the KC-150 on a speaker stand, or when
adjusting the height of the stand while the KC-150
remains mounted on it.
10
Appendices
Block Diagram
CH1
MIC/LINE
BALANCED
HOT
LINE OUT
COLD
CH 1 VOL
CH1
MIC/LINE
SUBWOOFER
OUT
CH 2
LINE
PHONES
CH 2 VOL
CH 3
LINE
TWEETER
CH 3 VOL
HIGH PASS FILTER
WOOFER
CH 4
MONITOR
MASTER VOL
CH 4 VOL
LOW
POWER AMP
HIGH
AUX IN
L
SPEAKER
LINE OUT
AUX IN
R
Main Specifications
Rated Power Output
Connectors
65 W
Nominal Input Level (1 kHz)
Input
Channel 1 (MIC/LINE): -50 – -20 dBu
Channel 2, 3 and 4 (LINE): -20 dBu
AUX IN:
-10 dBu
Nominal Output Level
LINE OUT:
SUBWOOFER OUT:
* 0 dBu = 0.775 Vrms
+4 dBu
+4 dBu
Speakers
30 cm (12 inches) x 1
Tweeter x 1
Controls
Channel 1 (MIC/LINE) Volume Knob
Channel 2 (LINE) Volume Knob
Channel 3 (LINE) Volume Knob
Channel 4 (MONITOR) Volume Knob
Equalizer: LOW Knob, HIGH Knob
VOLUME Knob
POWER Switch
Indicator
POWER
Channel 1 Input Jack (XLR type, 1/4” phone type)
Channel 2 Input Jack (1/4” phone type)
Channel 3 Input Jack (1/4” phone type)
Channel 4 Input Jack (1/4” phone type)
AUX IN Jack (RCA phono type)
LINE OUT Jack (1/4” phone type)
SUBWOOFER OUT Jack (1/4” phone type)
PHONES Jack (1/4” TRS phone type, mono signal output)
Power Supply
AC 117 V, AC 230 V, AC 240 V: 50/60 Hz
AC 220 V: 60 Hz
Power Consumption
55 W
Dimensions
480 (W) x 295 (D) x 435 (H) mm
18-15/16 (W) x 11-5/8 (D) x 17-1/8 (H) inches
Weight
14.0 kg
30 lbs 14 oz
Accessory
Owner’s Manual
* In the interest of product improvement, the specifications and/or
appearance of this unit are subject to change without prior notice.
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising