OPS300 Programmer's Guide(PDF)

OPS300 Programmer's Guide(PDF)

Programmer’s Guide

For OPS300

1

A1: Introduction

If you need to use your own Software Control program from a PC or WORKSTATION with an RS-232 or LAN port, the device allows communication through an ASCII code protocol.

The device treats any character that it receives on the RS-232 or LAN as a possible command but only accepts legal commands.

There is no starting/ending code needed in a command string.

A command can be a single character typed on a keyboard and does not require any special character before or after it.

(It is not necessary to press "ENTER" on the keyboard). A command can be preceded by a value (See chapter A-2).

When the device receives a valid command, it will execute the command. Then it will send back the status of the parameters that have changed due to this command.

If the command cannot be executed (value out of range, no signal on the selected input),etc. The device will just sends back the current status of the corresponding parameters.

If the command is invalid, an error response will be returned to the control device. All responses returned to the control device end with a carriage return <CR> and a line feed <LF> signaling the end of the response character string (see chapter A-3).

A2: Commands structure

The above listed devices share the same code structure.

Commands are made of numerical values for arguments followed by the command characters (one or Two case-sensitive alphabetical letters). Usually the same characters (letters) are used for the [read Command] as well as the [write command].

The indexes are defined numbers indicating the how the arguments for the command apply. For example a layer number, an input number, a preset number, etc.

They are separated with a comma.

There are commands without index and others with up to 3 indexes. Each index is followed by a comma character. The final argument, also refered to as the “value” does not have a comma between it and the command.

2

A [write command] is made of indexes followed by the numerical value followed by the command characters.

Write command = [[index,] ...] + Value + Character (s) code (s)

For example: “1,2,0IN” or “4YB”

A [read command] is made of indexes followed immediately by the command characters. (no numerical value)

Read command = [[index,] ...] Character (s) code (s)

For example: “1,2,IN” or “YB”

A3: Examples

Document notation:

1) Command without index : SWITCHER_MODE

Command to set the switcher mode to mixer mode: 0CM

Answer: CM0<CR><LF> which mean that the device is now working in mixer mode.

2) Command with 1 index : OFORMAT

Command to set the Main output format to XGA: 0,12OF

Answer: OF0,12<CR><LF> which mean that the main output format is now 1024x768

3) Command with 2 indexes : PE_INPUTNUM

Command to set the input 4 displayed in background layer of Next Preset: 1,2,4IN

Answer: IN1,1,4<CR><LF> which mean that the background layer of the next preset will display the input 4 signal

4) Read command without index : TAKEAVA

Read command to know if the TAKE command is available: TA

Answer: TA1<CR><LF> which mean that the device is ready to accept the TAKE command.

3

5) Read command with 2 indexes : SET_ASPECT_RATIO_OUT

Read command to know how is displayed a signal plugged on the input 4: 3,so

Answer: so3,2<CR><LF> which mean that the input 4 is displayed cropped

A4: Error codes

Answer: E10<CR><LF> which mean invalid command

Answer: E11<CR><LF> which mean index value error (index value out of range)

Answer: E12<CR><LF> which mean index number error (too or few indexes)

Some commands are only available as [Read command], they are status and are colored in blue as this line.

Some commands are colored in yellow as this line to indicate they were added or modified in this version.

A5 COMMUNICATION PORTS

4

Group

SYSTEM

Name

DIESE

READY

DEV

UPDATER

FACTORYRESET

POSMEMORYRESET

CSTORE

LOCK

LCDBRIGHTNESS

KEYBRIGHTNESS

TBAR_ENABLE

CONTROLS

COPKIND

COPPROGRESS

PRESET_MATRIX_MGMT

SWITCHER_MODE

AXION

AUTO_LOCK

AUTO_TAKE

Cmd Resp Description

# #

Request the retrieval of all the variables

Ready Device Flag * *

? DEV MMS device type yU yU Device reboot for update

YR YR

Apply factory settings to the device( except image settings )

YE YE Erase stored image settings

FLASH memory writing in

YS YS progess. Do not power off

YK YK

YB YB

Yb

YD YD

CK CK

CP CP

CR CR

CM CM Device operating mode yA

YL

Yb yA

YL

YT YT

Device locking

Front panel display brightness

Front panel keys brightness

Enable disable T-BAR

Kind of slow in-progress operation Rd

Progress percent of the slow operation

Preset management in matrix mode from the front panel

Device is driven by Orchestra

Forbide the use of a signal-less input

Automatic Take after an input change

Read / Min

Write value

Max value

Default

Values value

Rd/Wr 0 1 0

Rd 0 1

Rd 74 74 74

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd 0

Rd/Wr 0

Rd/Wr 1

Rd/Wr 10

Rd/Wr 0

Rd

0

0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

255

1

1

1

2

8

100

1

6

100

3

1

1

1

1

0

0

0

0

0

0

8

100

1

0

0

0

0

0

1

0

0= Initialization in progress

1 = Ready

74 = OPS-300

1 then 254 => Reboot

Auto reset

Auto reset

0 = Free

1 = Flash writing in progress

0 = No lock

1 = Locked menu

2 = Locked front panel

1, …, 8 = Brightness level, 12,5% step

1, …, 100 = Brightness level, 1% step

0 = None

1 = Auto centering

2 = Auto setting

3 = StandBy

4 = Picture recording

5 = Reset to default factory setting

6 = Reset User settings

Percent : 0 to 100%

0 = Preset management for both outputs

1 = Preset management for current output

2 = Preset management for output 1

3 = Preset management for output 2

0 = Seamless switcher mode

1 = Matrix mode

0 = Device is not driven by ORC-50

1 = Device is driven by Orc-50

0 = Signal less input can be selected

1 = Signal less input can not be selected

0 = AUTO-TAKE Disable

1 = AUTO-TAKE Enable

Index #1 Index #2

5

Group Name

AUTO_STEPBACK

FREEZE_MODE

FRAME_ALERT

TRANSPARENT_BACKGROUND

BLACK_FILL

DISABLE_ID

STDBYSTATUS

STDBYREQUEST

STDBYPROJ_ON

STANDBY

STDBYPROJ_OFF

STDBYPROJ_RATE

STDBYPROJ_CTRL

VERSION

VERI1

VERI2

Cmd Resp Description

Ys Ys

Ym Ym

Yf

Yt bF bI

Yf

Yt bF bI

Automatic preset toggle after a

TAKE

Input freeze mode

Back-up input when an input loose its signal

Disable the the black fiilng of the bakgrounfd live layer

Fill PIP with black depending on the aspect ratio

Disable Frame and Ids on the preview output

Read / Min

Write value

Max value

Default

Values value

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

1

1

12

1

1

0

0

0

1

0

0 = AUTO- PRESET-TOGGLE

Disable

1 = AUTO- PRESET-TOGGLE

Enable

0 = Freeze by input

1 = Freeze all inputs

0 = No input

1 = Input1

2 = Input2

3 = Input3

4 = Input4

5 = Input5

6 = Input6

7 = Input7

8 = Input8

9 = Input9

10 = Input10

11 = Input11

12 = Input12

0 = use BLACK_FILL

1 = Disable black filling only for background

0 = Disable black filling

1 = Enable black filling

Rd/Wr 0 1 0 wS wS wQ wQ

Standby mode Rd/Wr 0

Request for standby or wake up Rd/Wr 0

1

1

0

0

0 = Normal mode

1 = Standby mode

0 = Wake up

1 = Standby wN wN wF wF

Message to wake-up an output display device ( 50 characters)

Message to send an output display device to sleep ( 50 characters)

Rd/Wr 0

Rd/Wr 0

255

255

0

0 wR wR wC wC xi xj xi xj

Output display device UART speed

Byte 0 and 1 of the device ID

Byte 2 and 3 of the device ID

Rd/Wr 0

Rd/Wr 0

Rd

Rd

0

0

3

4

2

0

65535 0

65535 0

0 = 1200bauds

1 = 2400bauds

2 = 9600bauds

3 = 19200bauds

0 = No request

1 = Wake up request

2 = Standby request

3 = Clear Wake up message

4 = Clear standby message ex : AAAA ex : AAAA

Index #1

min = 0 max = 49

min = 0 max = 49

Index #2

6

Group Name

VERI3

VERI4

VERK

VERV

VERUPD

OPT

REV

IN_AUTOSET_ALL

INPUT

IN_AUTOSET

Cmd Resp Description

Read / Min

Write value

xk xk Byte 4 and 5 of the device ID Rd 0 xl xl Byte 6 and 7 of the device ID Rd 0 xK xV xU yo xK xV xU yo

Checksum/version of the programmable components

Variable set version

Updater version

Detected options

Rd/Wr 0

Rd

Rd

Rd

Rd

0

0

0

0

Max value

Default

Values value

65535 0

65535 0

65535 0

65535 42

65535 0

65535 0

255 0 ex : AAAA ex : AAAA bit 0 = Lan Module bit 1 = SDI In 1 board (SDI 1 and 2) bit 2 = Recording board bit 3 = CF Caecina bit 4 = CF Fannia bit 5 = CF Thrasea bit 6 = SDI In 2 board (SDI 3 and 4) bit 7 = Audio Evolution bit 8 = HDCP DVI In Evolution

Index #1

0 = Number of programmables components

1 = Main microcontroler

2 = Front panel micro-controler

3 = FPGA

Caecina

4 = FPGA Fannia

5 = FPGA

Thrasea

6 = Synchro

CPLD

Index #2

xR xR Moher board revision

Auto-setting request for all the

Ia Ia inputs

Rd/Wr 0 1 0

Ii Ii

Auto-setting request for the specified input

Rd/Wr 0 1 0

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

7

Group Name

IN_USR_FORMAT

Cmd Resp Description

iU iU

Format/standard of the input signal corrected by user

Read / Min

Write value

Rd/Wr 0

Max value

Default

Values value

42 0

0 = None

1 = Invalid

2 = Unknown

3 = SDTV NTSC

4 = SDTV PAL

5 = SDTV SECAM

6 = SDTV BW

7 = SDTV 480i

8 = SDTV 576i

9 = EDTV 480p

10 = EDTV 576p

11 = HDTV 720p

12 = HDTV 1035i

13 = HDTV 1080i

14 = HDTV 1080p

15 = HDTV 1080sF

16 = CPU VGA

17 = CPU 800x480

18 = CPU WVGA

19 = CPU SVGA

20 = CPU 1280x600

21 = CPU 720p RGB

22 = CPU XGA

23 = CPU WXGA

24 = CPU SWXGA

25 = CPU 800p RGB

26 = CPU SWXGA+

27 = CPU 1152x864

28 = CPU 900p RGB

29 = CPU 1600x900

30 = CPU 960p RGB

31 = CPU SXGA

32 = CPU 1360x1024

33 = CPU DILA4/3

34 = CPU SXGA+

35 = CPU WSXGA+

36 = CPU 1080p RGB

37 = CPU 2K

38 = CPU UXGA

39 = CPU WUXGA

40 = CPU 1920x1440

41 = CPU QXGA

42 = CPU 1366x768

Index #1 Index #2

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

8

Group Name

IN_TYPE

IN_SYNC_LOAD

Cmd Resp Description

iK iK Input signal type il il Analog H sync load

Read / Min

Write value

Rd/Wr 0

Rd/Wr 0

Max value

Default

Values value

17

1

13

0

Index #1

0 = SDTV Composite

1 = SDTV Y/C

2 = SDTV/EDTV/HDTV RGBS

TTL/Analog

3 = SDTV/EDTV/HDTV RGB SOG

4 = SDTV/EDTV/HDTV YUV

5 = Computer SOG

6 = Computer H&V or Composite

(TTL/Analog)

2 = Input3

7 = Computer B&W

8 = DVI-D EDTV/HDTV RGB 16-235

3 = Input4

4 = Input5

9 = DVI-D EDTV/HDTV YUV

5 = Input6

10 = DVI-D Computer RGB 0-255

1 = Input2

6 = Input7

11 = DVI-D Computer RGB 16-235

0 = Input1

7 = Input8

12 = SDI SDTV/HDTV

8 = Input9

13 = Analog Computer, separated

9 = Input10

H&V synchro

10 = Input11

14 = Analog Computer, composite

11 = Input12

TTL synchro

15 = Analog Computer, composite analog synchro

16 = Analog RGB video, composite

TTL synchro

17 = Analog RGB video, composite analog synchro

0 = Hi-Z

1 = 75 ohm loaded

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

9

Group Name

IN_USED

IN_SD_STD

IN_SD_STA

Cmd Resp Description

iu iS iS Decoded video standard iV iu iV

Input is enabled

Video Signal stability

Read / Min

Write value

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Max value

1

7

1

Default value

1

0

1

Values

0 = Auto

1 = NTSC (M,J)

2 = PAL (BDGHIN)

3 = PAL (M)

4 = PAL (N-Combination)

5 = NTSC 4.43

6 = SECAM

7 = PAL 60

0 = Stable Source ( DVD )

1 = VCR Source ( Video cassette recorder )

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

10

Group Name

IN_SYNCHRONIZED

IN_HDCP_ENABLE

IN_HDCP_CABLE_LEN

IN_KEYING_TYPE

KEYING

IN_KEYING_R_LEVEL

Cmd Resp Description

iY iH iC iY iH iC

KT KT

KR KR

VIS Synchronisation group

Enable/disable the HDCP support of a DVI input

Lenght of an DVI input cable

Keying type

Keying level (Red )

Read / Min

Write value

Max value

Default

Values value

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

4

1

2

4

255

0

1

0

0

0

Index #1

0 = Does not belong to any VIS

Group

1 = Groupe VIS 1 group for analog input

2 = Groupe VIS 2 group for analog input

3 = Groupe VIS 3 group for analog input

4 = Groupe VIS 4 group for analog input

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

8 = Input9

0 = Less than 10 meter cable length

9 = Input10

1 = 5 to 20 meters cable length

2 = More than 15 meters cable length

8 = Input9

9 = Input10

0 = No keying

1 = Luma Key Keying

2 = ChromaKey Keying

3 = Luma Key Keying + DSK

4 = ChromaKey Keying + DSK

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

11

Group Name

IN_KEYING_G_LEVEL

Cmd Resp Description

Read / Min

Write value

Max value

Default

Values value

KG KG Keying level (Green) Rd/Wr 0 255 255

IN_KEYING_B_LEVEL KB KB Keying level (Bule) Rd/Wr 0 255 0

IN_KEYING_TOLER KH KH

Keying Tolerance (for chroma and

Rd/Wr 0 luma key)

255 10

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

12

Group Name Cmd Resp Description

Read / Min

Write value

Max value

Default

Values value

IN_KEYING_LUMA_LOW_LEVEL KL KL Minimum luma level Rd/Wr 0 255 0

IN_KEYING_LUMA_HIGH_LEVEL KM KM Maximum luma level Rd/Wr 0 255 255

IN_KEYING_DSK_ALPHA KA KA Brightness of DSK background Rd/Wr 0 255 64

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

13

Group Name

INPUT

STATUS

IN_KEYING_INVERT

IN_KEYING_GRAB_ENABLE

IN_KEYING_GRAB_GET

IN_KEYING_GRAB_H

IN_KEYING_GRAB_V

SIG_HPOL

SIG_VPOL

Cmd Resp Description

KI

Kg

Kc sh sv

KI

Kg

Kc sh sv

Invert keying area

Enable/disable the keying color grabber mode

Capture the coolor selected by the grabber and apply the settings

Input H sync polarity

Input V sync polarity

Read / Min

Write value

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Kh Kh Horizontal position of the grabber Rd/Wr 0

Kv Kv Vertical position of the grabber Rd/Wr 0

Rd

Rd

0

0

Max value

1

Default value

Values

1 0

0 = Disable the grabber

1 = Enable the grabber

Percent of OSCREEN_UTIL_H 1 0

65535 32768 Precent of OSCREEN_UTIL_V

65535 32768 Auto reset

1

1

0

0

0

0 = Negative Synchro

1 = Positive Synchro

0 = Negative Synchro

1 = Positive Synchro

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

14

Group Name

SIG_SYNC_TYPE

SIG_FREQ_FIELD

SIG_FREQ_LINE

Cmd Resp Description

sK sf sf Input frame frequency sl sK sl

Input sync type

Input line frequency

Read / Min

Write value

Rd

Rd

Rd

0

0

0

Max value

3

Default value

0

65535 0

65535 0

Values

0 = Séparated Synchros H&V

1 = Composite TTL Synchro

2 = Composite Analog Synchro

3 = Synchro on Green (SOG)

Unit = 1/100Hz

Unit = 1/100Hz

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

15

Group Name

SIG_COMPLETE

Cmd Resp Description

sc sc Input scan completed

Read / Min

Write value

Max value

Default

Values value

Rd 0 1 0

0 = scan in progress or failed

1 = scan completed

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

16

Group Name

SIG_DETECTED_FORMAT

Cmd Resp Description

sD sD Input detected format name

Read / Min

Write value

Rd 0

Max value

Default

Values value

42 0

0 = None

1 = Invalid

2 = Unknown

3 = SDTV NTSC

4 = SDTV PAL

5 = SDTV SECAM

6 = SDTV BW

7 = SDTV 480i

8 = SDTV 576i

9 = EDTV 480p

10 = EDTV 576p

11 = HDTV 720p

12 = HDTV 1035i

13 = HDTV 1080i

14 = HDTV 1080p

15 = HDTV 1080sF

16 = CPU VGA

17 = CPU 800x480

18 = CPU WVGA

19 = CPU SVGA

20 = CPU 1280x600

21 = CPU 720p RGB

22 = CPU XGA

23 = CPU WXGA

24 = CPU SWXGA

25 = CPU 800p RGB

26 = CPU SWXGA+

27 = CPU 1152x864

28 = CPU 900p RGB

29 = CPU 1600x900

30 = CPU 960p RGB

31 = CPU SXGA

32 = CPU 1360x1024

33 = CPU DILA4/3

34 = CPU SXGA+

35 = CPU WSXGA+

36 = CPU 1080p RGB

37 = CPU 2K

38 = CPU UXGA

39 = CPU WUXGA

40 = CPU 1920x1440

41 = CPU QXGA

42 = CPU 1366x768

Index #1 Index #2

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

17

Group Name

SIG_CURRENT_FORMAT

Cmd Resp Description

sF sF Input current format name

Read / Min

Write value

Rd 0

Max value

Default

Values value

42 0

0 = None

1 = Invalid

2 = Unknown

3 = SDTV NTSC

4 = SDTV PAL

5 = SDTV SECAM

6 = SDTV BW

7 = SDTV 480i

8 = SDTV 576i

9 = EDTV 480p

10 = EDTV 576p

11 = HDTV 720p

12 = HDTV 1035i

13 = HDTV 1080i

14 = HDTV 1080p

15 = HDTV 1080sF

16 = CPU VGA

17 = CPU 800x480

18 = CPU WVGA

19 = CPU SVGA

20 = CPU 1280x600

21 = CPU 720p RGB

22 = CPU XGA

23 = CPU WXGA

24 = CPU SWXGA

25 = CPU 800p RGB

26 = CPU SWXGA+

27 = CPU 1152x864

28 = CPU 900p RGB

29 = CPU 1600x900

30 = CPU 960p RGB

31 = CPU SXGA

32 = CPU 1360x1024

33 = CPU DILA4/3

34 = CPU SXGA+

35 = CPU WSXGA+

36 = CPU 1080p RGB

37 = CPU 2K

38 = CPU UXGA

39 = CPU WUXGA

40 = CPU 1920x1440

41 = CPU QXGA

42 = CPU 1366x768

Index #1 Index #2

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

18

Group Name

SIG_FORMAT_LIST

SIG_SCANTYPE

SIG_HTOTAL_THEORIC

Cmd Resp Description

sL ss sH sL ss sH

Bit field of the fomats compatible with the detected format

Input scan type

Total number of pixels per line

Read / Min

Write value

Rd 0

Rd

Rd

0

0

Max value

255

3

Default value

0

0

65535 0

Values

0 = Progressive

1 = Interleaved, Top field first

2 = Interleaved, Bottom field first

3 = Segmented frame

Unit = pixels

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

0 = Bits 0 to 7

Slice

1 = Bits 8 to 15

Slice

2 = Bits 16 to 23

Slice

3 = Bits 24 to 31

Slice

4 = Bits 32 to 39

Slice

5 = Bits 40 to 47

Slice

19

Group Name

SIG_HTOTAL_MAXI

SIG_WIDTH

SIG_HEIGHT

Cmd Resp Description

Read / Min

Write value

Max value

Default

Values value

sM sM

Maximal number of pixels per input line

Rd 0 65535 0 Unit = pixels sw sw Input displayed pixel count Rd 0 65535 0 Unit = pixels st st Input displayed line count Rd 0 65535 0 Unit = pixels

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

20

Group Name

SIG_HDCP

INPUT

SETTINGS

SIG_MEM_SLOT

SET_HPOS

Cmd Resp Description

sn sn Input HDCP status sS sS Memory slot index

Read / Min

Write value

Max value

Default

Values value

Rd 0 1 0

Rd 0 255 255

SH SH Input horizontal position Rd/Wr 0 2048 1024 1024 = neutral

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

21

Group Name

SET_VPOS

SET_HSIZE

SET_VSIZE

Cmd Resp Description

SV SV Input vertical position Rd/Wr 0 2048 1024 1024 = neutral

Sw Sw Input horizontal size Rd/Wr 0 4096 2048 2048 = neutral

Sh Sh Input vertical size

Read / Min

Write value

Max value

Default

Values value

Rd/Wr 0 4096 2048 2048 = neutral

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

22

Group Name

SET_BRIGHTNESS

SET_CONTRAST

SET_COLOR

Cmd Resp Description

Sg Sg Input brightness

Read / Min

Write value

Max value

Default

Values value

Rd/Wr 0 255 128 128 = neutral

Sc

Sr

Sc

Sr

Input Contrast

Input color level

Rd/Wr 0

Rd/Wr 0

255 128 128 = neutral

255 128 128 = neutral

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

23

Group Name

SET_HUE

SET_HTOTAL

SET_PHASE

Cmd Resp Description

Read / Min

Write value

Max value

Default

Values value

Su Su Input hue (NTSC only) Rd/Wr 0 255 128 128 = neutral

ST ST

SS SS

Input total pixel per line

Input Phase

Rd/Wr 0 65535 0

Rd/Wr 0 31 16

Unit = pixels.

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

24

Group Name

SET_AUTOCAD

SET_USER_GAIN_R

Cmd Resp Description

Sa Sa Input autocentering reques Rd/Wr 0 1 0 Auto reset sr sr

ADC R channel adjustment

(advanced setting)

Read / Min

Write value

Max value

Default

Values value

Rd/Wr 0 255 128 128 = neutral

SET_USER_GAIN_G sg sg

ADC G channel adjustment

(advanced setting)

Rd/Wr 0 255 128 128 = neutral

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

25

Group Name

SET_USER_GAIN_B

SET_PULLDOWN_2_2

SET_PULLDOWN_3_2

Cmd Resp Description

sb sb

ADC B channel adjustment

(advanced setting)

Sn Sn

Enable/disable the auto 2:2 pulldown

Sp Sp

Enable/disable the auto 3:2 pulldown

Read / Min

Write value

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Max value

255

1

1

Default value

128

1

1

Values

128 = neutral

0 = Disable automatic detection

1 = Enable automatic detection

0 = Disable automatic detection

1 = Enable automatic detection

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

26

Group Name

SET_CROP_WIN_POS_H

SET_CROP_WIN_POS_V

SET_CROP_WIN_SIZE_H

Cmd Resp Description

SI SI

SK SK

Cropping window horizontal position

Horizontal cropping

Read / Min

Write value

Rd/Wr 0 65535 32768

Percent = 65535 = 100% : all cropping on the left

SJ SJ Cropping window vertical position Rd/Wr 0 65535 32768

Percent = 65535 = 100% : all cropping on the top

Rd/Wr 0

Max value

Default

Values value

58981 0 Percent = 65535 = 100%

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

27

Group Name

SET_CROP_WIN_SIZE_V

SET_ASPECT_RATIO_IN

SET_ASPECT_RATIO_OUT

Cmd Resp Description

SL si

SL si

Vertical cropping

Input image aspect ratio so so Output image aspect ratio

Read / Min

Write value

Max value

Default

Values value

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

58981 0

4

3

0

1

Index #1

Percent = 65535 = 100%

0 = 4/3 Fullscreen

1 = 4/3 with 16/9 content + black stripes

2 = 4/3 with 2.35 content + black stripes

3 = 4/3 with 16/9 content without black stripes

4 = 19/9 with 4/3 content + black stripes

0 = Distorted, input aspect ratio not preserved

1 = Not distorted, black bands added

2 = Not distorted, no black bands added

3 = Not distorted and no scaling

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

28

Group Name

SET_OVER_SCAN

Cmd Resp Description

Read / Min

Write value

Max value

Default

Values value

sO sO input image Overscan/Underscan Rd/Wr 0 1 1

SET_FORCE_4_3 SF SF

Force the aspect ratio of

PAL/NTSC input to 4/3

Rd/Wr 0 1 1 1 = forced

SET_RESET_SETTINGS Ss Ss Current input default settings Rd/Wr 0 1 0

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

29

Group Name

SET_FREEZE

SET_MOTION_DETECT

PRESET

ELEMENT

PE_INPUTNUM

Cmd Resp Description

Sf Sf Freeze of the input

Read / Min

Write value

Max value

Default

Values value

Rd/Wr 0 1 0 1 = Freeze

Sm Sm

0 : max correction; 15 : min correction

Rd/Wr 0 15 15

IN IN

Displayed input number or frame or logo number

Rd/Wr 0 12 0

0 = No input

1 = Input1

2 = Input2

3 = Input3

4 = Input4

5 = Input5

6 = Input6

7 = Input7

8 = Input8

9 = Input9

10 = Input10

11 = Input11

12 = Input12

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

Index #2

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

30

Group Name

PE_SOURCENUM

PE_AUDIO_AUX_MUTE

Cmd Resp Description

IS IS Source number

Read / Min

Write value

Max value

Default

Values value

Rd/Wr 0 64 0 Same Orc-50

Aa Aa Auxiliary input mixing enable Rd/Wr 0 1 0 1 = Enable.

Index #1

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

31

Group Name

PE_SMOOTH_MOVE

PE_NEW_ID

Cmd Resp Description

Read / Min

Write value

Max value

Default

Values value

ps ps « Smooth Move » activation Rd/Wr 0 1 1 1 = Enable. pN pN Unique layer identifier number Rd/Wr 0 1 0

Index #1

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

32

Group Name

PE_POS_H

PE_POS_V

Cmd Resp Description

pH pH

Layer left H position on output screen pV pV

Layer top V position on output screen

Read / Min

Write value

Rd/Wr 0

Rd/Wr 0

Max value

Default value

65535 32768

Values

Unit = pixels ( 32768 = screen left border )

65535 32768

Unit = pixels ( 32768 = screen top border )

Index #1

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

33

Group Name

PE_SIZE_H

PE_SIZE_V

Cmd Resp Description

pW pW

Layer H size on output screen

(without borders)

Rd/Wr 0 65535 1600

Unit = pixels ( Max=16x2048 =

32768) pS pS

Layer V size on output screen

(without borders)

Read / Min

Write value

Rd/Wr 0

Max value

Default

Values value

65535 1200

Unit = pixels (Max=16x2048 =

32768)

Index #1

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

34

Group Name

PE_CROP_WIN_POS_H

PE_CROP_WIN_POS_V

Cmd Resp Description

CH CH

CV CV

Cropping window horizontal position

Read / Min

Write value

Rd/Wr 0

Cropping window vertical position Rd/Wr 0

Max value

Default value

Values Index #1

65535 32768

Unit = percent ( 65535 = 100% = : all cropping on the left )

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

65535 32768

Unit = percent ( 65535 = 100% = : all cropping on the top )

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

35

Group Name

PE_CROP_WIN_SIZE_H

PE_CROP_WIN_SIZE_V

Cmd Resp Description

CW CW Horizontal cropping

CS CS Vertical cropping

Read / Min

Write value

Rd/Wr 0 58981 0 Percent = 65535 = 100%

Rd/Wr 0

Max value

Default

Values value

58981 0 Percent = 65535 = 100%

Index #1

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

36

Group Name

PE_ALPHA

PE_BORDER_STYLE

Cmd Resp Description

pA pA Layer transparency bS bS Border style

Read / Min

Write value

Rd/Wr 0 255 255

0 = 100% = transparent

255 = 0% = visible

Rd/Wr 0

Max value

1

Default

Values value

0

0 = No border

1 = Colored edge

Index #1

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

37

Group Name

PE_BORDER_COLOR

PE_BORDER_ALPHA

Cmd Resp Description

bC bC Border color bA bA Border transparency

Read / Min

Write value

Rd/Wr 0

Max value

Default

Values value

544 33 Color number

Rd/Wr 0 255 255

0 = 100% = transparent

255 = 0% = visible

Index #1

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

38

Group Name

PE_BORDER_SIZE_H

PE_BORDER_SIZE_V

Cmd Resp Description

bH bH Border H size bV bV Border V size

Read / Min

Write value

Max value

Default

Values value

Rd/Wr 0 127 10 Unit = pixels

Rd/Wr 0 127 10 Unit = pixels

Index #1

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

39

Group Name

PE_OPENING_TRANSITION

PE_OPENING_TRANSITION_WAY

Cmd Resp Description

oT oT oW oW

Layer opening transition type

Read / Min

Write value

Rd/Wr 0

Layer opening transition direction Rd/Wr 0

Max value

4

10

Default value

2

0

Values

0 = Left to right

1 = Right to left

2 = Bottom to top

3 = Top to bottom

4 = Vertical from/to center

5 = Horizontal from/to center

6 = H&V rom/to center

7 = From SW to NE

8 = From SE to NW

9 = From NW to SE

10 = From NE to SW

Index #1

0 = Cut

1 = CleanCut

2 = Fade

3 = Slide (associée à 1 trajectoire)

4 = Wipe (associée à 1 trajectoire)

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

40

Group Name

PE_OPENING_DURATION

PE_CLOSING_TRANSITION

Cmd Resp Description

oD oD cT cT Layer closing transition type

Read / Min

Write value

Layer opening transition duration Rd/Wr 0

Rd/Wr 0

Max value

255

4

Default value

10

2

Values

Unit = 1/10s

Index #1

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Cut

1 = CleanCut

2 = Fade

3 = Slide (associée à 1 trajectoire)

4 = Wipe (associée à 1 trajectoire)

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

41

Group Name

PE_CLOSING_TRANSITION_WAY

PE_CLOSING_DURATION

PRESET

CONTROL

TAKE

TAKEAVA

Cmd Resp Description

Read / Min

Write value

Max value

Default

Values value

cW cW Layer closing transition direction Rd/Wr 0 10 0

0 = Left to right

1 = Right to left

2 = Bottom to top

3 = Top to bottom

4 = Vertical from/to center

5 = Horizontal from/to center

6 = H&V rom/to center

7 = From SW to NE

8 = From SE to NW

9 = From NW to SE

10 = From NE to SW cD cD Layer closing transition duration Rd/Wr 0 255 10 Unit = 1/10s

TK TK

TAKE, Next preset becomes

Current

TA TA Available TAKE flag

Rd/Wr 0

Rd 0

1

1

0

1

Index #1

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory

Preset 1

4 = Memory

Preset 2

5 = Memory

Preset 3

6 = Memory

Preset 4

Index #2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

0 = Background

Frame for output

1

1 = Background

Frame for output

2 in matrix mode

2 = Background

Layer for output 1

3 = Pip 1 Layer for output1

Background

Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output

1

9 = Audio Output

2

42

Group Name

TAKEINFO

TBAR

COPY_FROM

COPY_TO

COPY_SPLIT

COPY_CTRL

PREVIEWED_LAYER

Cmd Resp Description

TI

NT NT

Nf

Nt

Ns

Nc

TI

Nf

Nt

Ns

Nc

TAKE information

TBAR value

Source for preset copy

Destination for preset copy

Preset partial copy control

Preset copy control

NC NC

Previewed layed (layer that is visible on preview screen)

Read / Min

Write value

Max value

Default

Values value

Rd 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

2

10000 0

6

6

2

1

7

0

0

0

0

0

2

0 = 1 shot TAKE

1 = 2 shot TAKE

2 = Sequenced TAKE

Unit = 0,01%

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory Preset 1

4 = Memory Preset 2

5 = Memory Preset 3

6 = Memory Preset 4

0 = Current preset

1 = Next preset

2 = Previous preset

3 = Memory Preset 1

4 = Memory Preset 2

5 = Memory Preset 3

6 = Memory Preset 4

0 = Full Preset copy

1 = Output1 preset copy

2 = Output2 preset copy

Auto reset

0 = Background Frame for output 1

1 = Background Frame for output 2 in matrix mode

2 = Background Layer for output 1

3 = Pip 1 Layer for output1

Background Layer for output 2 in matrix mode

4 = Pip 2 Layer for output1

6 = Logo 1

7 = Logo 2

8 = Audio Output 1

9 = Audio Output 2

Index #1 Index #2

43

Group Name

SET_QUAD_LAYOUT

R_FLICK

SETTINGS R_GAMMA

R_SHARPNESS

Cmd Resp Description

NQ NQ

Quadravision Layout request

(auto-reset)

Rf

Rg Rg

Rs

Rf

Rs

Anti-flicker level

Gamma correction level

Sharpness correction Level

Read / Min

Write value

Max value

Default

Values value

Index #1

Rd/Wr 13

Rd/Wr 0

Rd/Wr 5

Rd/Wr 0

25

7

40

255

0

2

10

128

13 = Reset of layer properties

14 = Background Live + Top Left

PiP

15 = Background Live + Top Right

PiP

16 = Background Live + Bottom Left

PiP

17 = Background Live + Bottom

Right PiP

18 = Background Frame + 2 Left

Right PiPs

19 = Background Frame + 2 Top

Bottom PiPs

20 = Background Frame + 1 Right

PiP + 2 Top Bottom PiPs

21 = Background Frame + 1 Left PiP

+ 2 Top Bottom PiPs

22 = Background Frame + 1Top PiP

+ 2 Left Right PiPs

23 = Background Frame + 1 Bottom

PiP + 2 Left Right PiPs

24 = Background Frame + 3 horizontal PiPs

25 = Background Frame + 3 diagonal PiPs

0 = No antif-flicker

Unit = 1/10

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

128 = neutral

0 = Main output

1 = Preview output

2 = Recording output

Index #2

44

Group Name

OUTPUT OFORMAT

Cmd Resp Description

OF OF Output format

Read / Min

Write value

Rd/Wr 0

Max value

Default

Values value

37 0

0 = PAL

1 = NTSC

2 = 480p

3 = 576p

4 = SMPTE296M

5 = SMPTE260M

6 = SMPTE274M

7 = SMPTE274M

8 = SMPTE274M

9 = 640 x 480 4/3

10 = 848 x 480 16/9

11 = 800 x 600 4/3

12 = 1024 x 768 4/3

13 = 1360 x 768 16/9

14 = 1280 x 800 16/9

15 = 1280 x 1024 5/4

16 = 1400 x 1050 5/3

17 = 1680 x 1050 16/9

18 = 1600 x 1200 4/3

19 = 1920 x 1200 16/9

20 = 2048 x 1080

21 = 1280 x 720 16/9

22 = 1920 x 1080 16/9

23 = 1920 x 1080 16/9 (HD)

24 = 1920 x 1080 16/9 (SHARP)

25 = 1920 x 1080 16/9 (SHARP 2)

26 = 1440 x 900 16/10

27 = 1280 x 768 15/9

28 = 1366 x 800 15/9

29 = 1366 x 768 16/9

30 = Computer Custom 1

31 = Computer Custom 2

32 = Computer Custom 3

33 = Computer Custom 4

34 = Computer Custom 5

35 = Computer Custom 6

36 = Computer Custom 7

37 = Computer Custom 8

Index #1

0 = Main output

1 = Preview output

2 = Recording output

Index #2

45

Group Name

ORATE

OSIGTYPEANALOG

OSIGTYPEDIGITAL

OSYNCPOL

Cmd Resp Description

OR OR

OA OA

OD OD

Output rate

Analog output type

Digital output type

OS OS Analog output sync polarity

Read / Min

Write value

Rd/Wr 0

Max value

Default

Values value

12 8

0 = Custom Field Rate

1 = 23,97 Hz

2 = 24 Hz

3 = 25 Hz

4 = 29,97 Hz

5 = 30 Hz

6 = 50 Hz

7 = 59,94 Hz

8 = 60 Hz

9 = 72 Hz

10 = 75 Hz

11 = 85 Hz

12 = 100 Hz

Rd/Wr 0 3 0

0 = RGBs

1 = RGsB (SOG)

2 = RGB H&V

3 = YUV

Rd/Wr 0

Rd/Wr 0

2

3

0

0

Index #1

0 = Main output

1 = Preview output

2 = Recording output

0 = RGB 0-255 ( full scale )

1 = RGB 16-235 ( reduced scale )

2 = YUV

0 = negative H&V synchro

1 = Synchros H négative et V positive

2 = Synchros H positive et V négative

3 = Synchros H et V positives

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

Index #2

46

Group Name

OBACKCOLORPREDEF

OBACKCOLORHUE

OBACKCOLORSAT

Cmd Resp Description

OC OC

Output background pre-defined color

Read / Min

Write value

Rd/Wr 0

Max value

Default

Values value

32 0

0 = Black

1 = Navy blue

2 = Blue

3 = Green Blue

4 = Water Blue

5 = Turquoise blue

6 = Dark green

7 = Green

8 = Lime

9 = Light green

10 = Dark red

11 = Red

12 = Tomato red

13 = Bordeaux

14 = Brown

15 = Chocolate

16 = Orange

17 = Gold

18 = Yellow

19 = Indigo blue

20 = Purple

21 = Light red

22 = Fuchsia

23 = Salmon

24 = Rose

25 = Olive reen

26 = Grey

27 = Silver

28 = Lavender blue

29 = Beige

30 = Azur

31 = White

32 = Custom

OG OG Output background hue Rd/Wr 0 240 160

OJ OJ Output background saturation Rd/Wr 0 240 0

Index #1 Index #2

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

47

Group Name

OBACKCOLORLUMA

OPATTERN

OBLACK

OUTIL_H

OUTIL_V

OFIELDRATE

OIMAGE_OVERSCAN

OSETDETECTHDCP

Cmd Resp Description

OI OI Output background brightness

Read / Min

Write value

Rd/Wr 0

Max value

240

Default

Values value

0

Index #1

0 = Main output

1 = Preview output

2 = Recording output

Index #2

OP OP

OB OB

OH OH

OV OV

OT OT

OO OO Image Overscan / Underscan

Oh Oh

Output test pattern

Output black control

Output H size

Output V size

Output frame frequency

Enable/disable the Output HDCP detection

Rd/Wr 0

Rd/Wr 0

Rd 0

Rd

Rd

0

100

Rd/Wr 0

Rd/Wr 0

8

1

0

0

65535 1600

65535 1200

10000 6000

1

4

0

1

0 = No pattern

1 = Vertical Grey Scale

2 = Horizontal Grey Scale

3 = Vertical Color Bar

4 = Horizontal Color Bar

5 = Grid

6 = SMPTE

7 = Burst

8 = Centering

0 = Normal output

1 = Black output

Unit = pixels

Unit = pixels

Unit = 1/100Hz

0 = Disable HDCP detection

1 = Automatic HDCP detection

2 = HDCP Configuration 1

3 = HDCP Configuration 2

4 = HDCP Configuration 3

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

48

Group Name

OISHDCP

OSYNCOUTPUT

REFREQUEST

REFERENCE

REFCURRENTREQUEST

REFMODE

Cmd Resp Description

On On

Om Om

Xr

Xe

Xr

Xe

Xm Xm

Output HDCP status

Output 2 copies the format and rate of output 1

Framelock source requested by user

Current Frame Lock source

Follow mode requested by user

Read / Min

Write value

Max value

Default

Values value

Rd 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

1

1

16

16

5

0

0

0

0

0

Index #1

0 = Main output

1 = Preview output

2 = Recording output

Index #2

0 = Analog input 1 as reference

1 = Analog input 2 as reference

2 = Analog input 3 as reference

3 = Analog input 4 as reference

4 = Analog input 5 as reference

5 = Analog input 6 as reference

6 = Analog input 7 as reference

7 = Analog input 8 as reference

8 = DVI 1 input as reference

9 = DVI 2 input as reference

10 = SDI 1 input as reference

11 = SDI 2 input as reference

14 = Back End 1 as reference

15 = Back End 2 as reference

16 = Back End 3 as reference

0 = Analog input 1 as reference

1 = Analog input 2 as reference

2 = Analog input 3 as reference

3 = Analog input 4 as reference

4 = Analog input 5 as reference

5 = Analog input 6 as reference

6 = Analog input 7 as reference

7 = Analog input 8 as reference

8 = DVI 1 input as reference

9 = DVI 2 input as reference

10 = SDI 1 input as reference

11 = SDI 2 input as reference

14 = Back End 1 as reference

15 = Back End 2 as reference

16 = Back End 3 as reference

0 = Internal

1 = Follow x1/2

2 = Follow x1

3 = Follow x2

4 = Follow x3

5 = Asynchronous Follow

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

49

Group Name

REFCURRENTMODE

REFFREQ

REFLOCKSTATUS

PMODE

PEXECUTE

LOGOS

FRAMES

PSTATUS

PFRAMES_VALID

PLOGOS_VALID

PCAPTURE_ORIGIN

PCAPTURE_LEFT

PCAPTURE_TOP

PCAPTURE_WIDTH

PCAPTURE_HEIGHT

Cmd Resp Description

Xc Xc Current follow mode

Read / Min

Write value

Rd/Wr 0

Max value

Default

Values value

5 0

0 = Internal

1 = Follow x1/2

2 = Follow x1

3 = Follow x2

4 = Follow x3

5 = Asynchronous Follow

Index #1

0 = Main output

1 = Preview output

2 = Recording output

Xt

Xl

Xt

Xl

Frame rate of the reference signal Rd

Framelock locked status Rd

0

0

65535 0

1 0

Unit = 1/100Hz

1 = locked

PM PM

PG PG

Picture mode

Picture control

Rd/Wr 0

Rd/Wr 0

5

1

0

0

0 = Normal mode

1 = Memory recall of logos and frames

2 = Logo recording mode

3 = Animated logo recording mode

4 = Frame recording mode

5 = Deleting picture mode

If PMODE = Savexxx => Store the

PCAPTURE_INDEX image

If PMODE = Erasexxx => Delete the PCAPTURE_INDEX image

Auto reset

PE PE Picture management status Rd 0 5 0

0 = Free

1 = Recalling picture

2 = Storing picture

3 = Picture format not compliant with current output format

4 = Deleting a picture

5 = Flash access error

0 = No image

1 = Image is valid

PF PF

PZ PZ

Frames validity (bitfield : bit0 =

Frame1)

Logos validity (bitfield : bit0 =

Logo1)

Rd

Rd

0

0

255

511

0

0

0 = No image

1 = Image is valid

PS PS

PL PL

Select the output that will be used

Rd/Wr 0 for capture

Picture capture H position

1 0

0 = Main output

1 = Preview output

2 = Recording output

Rd/Wr 32768 65535 32768 Unit = pixels

PT PT Picture capture V position

PW PW Picture capture H size

PH PH Picture capture V size

Rd/Wr 32768 65535 32768 Unit = pixels

Rd/Wr 0 32767 400 Unit = pixels

Rd/Wr 0 32767 300 Unit = pixels

0 = Main output

1 = Preview output

2 = Recording output

0 = Main output

1 = Preview output

2 = Recording output

Index #2

50

Group Name

PCAPTURE_KEYING_TYPE

PCAPTURE_KEYING_R_LEVEL

PCAPTURE_KEYING_G_LEVEL

PCAPTURE_KEYING_B_LEVEL

PCAPTURE_KEYING_TOLER

PC PC Picture Keying Level (Red or Tint) Rd/Wr 0

PD PD Picture Keying Level (Green) Rd/Wr 0

PJ PJ Picture Keying Level (Blue)

PK PK Keing Tolerance

Rd/Wr 0

Rd/Wr 0

PCAPTURE_KEYING_LUMA_LOW_LEVEL PP PP Minimum Luma Level

PCAPTURE_KEYING_LUMA_HIGH_LEVELPY PY Maximum Luma Level

PCAPTURE_KEYING_INVERT PO PO Keying Invert

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

PCAPTURE_KEYING_GRAB_ENABLE

Cmd Resp Description

PB PB

PQ PQ

Picture Keying Type

Keying Grabber Activate

Read / Min

Write value

Rd/Wr 0

Max value

Default

Values value

2 0

0 = No keying

1 = Luma Key Keying

2 = ChromaKey Keying

3 = Luma Key Keying + DSK

4 = ChromaKey Keying + DSK

Rd/Wr 0

255

255

255 128

255 10

255 64

255 192

1

1

128

128

0

0

0 = Disable the grabber

1 = Enable the grabber

PCAPTURE_KEYING_GRAB_GET

PCAPTURE_KEYING_GRAB_H

PCAPTURE_KEYING_GRAB_V

PCAPTURE_BACK_COLOR

PCAPTURE_CAPTURE_TIME

PR PR

Keying update (capture and apply

Rd/Wr 0 new value)

PU PU Keying grabber position H Rd/Wr 0

PV PV Keying grabber position V Rd/Wr 0

Pc Pc Cutout color for picture capture Rd/Wr 0

Pt Pt Capture time for an animated logo Rd/Wr 0

1 0 Percent of OSCREEN_UTIL_H

65535 32768 Percent of OSCREEN_UTIL_V

65535 32768 Auto reset

7

100

0

0

0 to 7

0 = 0s

100 = 10s

PCAPTURE_MAX_FRAME

PCAPTURE_FRAME_COUNT

PCAPTURE_REFRESH_INTERVAL

Pm Pm

PN PN

PI PI

Maximal number of frames of an animated logo

Rd 1

Number of frames of an animated

Rd/Wr 1 logo

Time between 2 frames of an animated logo

Rd/Wr 1

255

255

80

1

10000 56

1 à 255

Unit = 1ms

PCAPTURE_INDEX PX PX ID of the picture to capture Rd/Wr 0 16 0

0 = No Picture

1 = Logo 1

2 = Logo 2

3 = Logo 3

4 = Logo 4

5 = Logo 5

6 = Logo 6

7 = Logo 7

8 = Logo 8

9 = Frame 1

10 = Frame 2

11 = Frame 3

12 = Frame 4

13 = Frame 5

14 = Frame 6

15 = Frame 7

16 = Frame 8

Index #1 Index #2

51

Group Name

PSTATUS_WIDTH

Cmd Resp Description

Read / Min

Write value

Max value

Default

Values value

Pw Pw Picture H size Rd 0 32767 0

PSTATUS_HEIGHT Ph Ph Picture V size Rd 0 32767 0

Index #1

1 = Logo 1

2 = Logo 2

3 = Logo 3

4 = Logo 4

5 = Logo 5

6 = Logo 6

7 = Logo 7

8 = Logo 8

9 = Frame 1

10 = Frame 2

11 = Frame 3

12 = Frame 4

13 = Frame 5

14 = Frame 6

15 = Frame 7

16 = Frame 8

1 = Logo 1

2 = Logo 2

3 = Logo 3

4 = Logo 4

5 = Logo 5

6 = Logo 6

7 = Logo 7

8 = Logo 8

9 = Frame 1

10 = Frame 2

11 = Frame 3

12 = Frame 4

13 = Frame 5

14 = Frame 6

15 = Frame 7

16 = Frame 8

Index #2

52

Group Name

PSTATUS_STYLE

PSTATUS_FRAME_COUNT

Cmd Resp Description

Ps Ps

Pn Pn

Logo style

Read / Min

Write value

Max value

Default

Values value

Rd 0 2 0

0 = Normal logo

2 = Frame

Number of frames of an animated

Rd 1 logo

255 1

Index #1

1 = Logo 1

2 = Logo 2

3 = Logo 3

4 = Logo 4

5 = Logo 5

6 = Logo 6

7 = Logo 7

8 = Logo 8

9 = Frame 1

10 = Frame 2

11 = Frame 3

12 = Frame 4

13 = Frame 5

14 = Frame 6

15 = Frame 7

16 = Frame 8

1 = Logo 1

2 = Logo 2

3 = Logo 3

4 = Logo 4

5 = Logo 5

6 = Logo 6

7 = Logo 7

8 = Logo 8

9 = Frame 1

10 = Frame 2

11 = Frame 3

12 = Frame 4

13 = Frame 5

14 = Frame 6

15 = Frame 7

16 = Frame 8

Index #2

53

Group

LAN

Name

PSTATUS_REFRESH_INTERVAL

LANENABLE

LANRESET

LANSTORE

LANIP

LANPORT

LANNETMASK

LANPROTOCOL

Cmd Resp Description

Pi Pi

Time between 2 frames of an animated logo ne ne LAN enable nr nr LAN factory parameters reset ns ns LAN parameters update nw nw np nk nt np nk nt

LAN devices addresses

LAN port numbers

LAN netmask

LAN protocol

Read / Min

Write value

Max value

Default

Values value

Rd/Wr 1

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

10000 56

1

1

1

0

0

0

Index #1

Unit = 1ms

0 = Enable RS232 ( disable LAN )

1 = Enable LAN ( disable RS232 )

Auto reset

Auto reset

1 = Logo 1

2 = Logo 2

3 = Logo 3

4 = Logo 4

5 = Logo 5

6 = Logo 6

7 = Logo 7

8 = Logo 8

9 = Frame 1

10 = Frame 2

11 = Frame 3

12 = Frame 4

13 = Frame 5

14 = Frame 6

15 = Frame 7

16 = Frame 8

Index #2

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

255

1

192

24 8

1

IP : 0 to 255

65535 10500

Local port : 10000 à 10999

Remote port : 0 à 65500

Number of 0bits from the right

0 = UDP Protocol

1 = TCP protocol

2 = AMX Protocol

0 = Device

1 = Remote

2 = Gateway

0 = Device

1 = Remote

2 = Gateway

0 = IP address high byte

1 = IP address mid high byte

2 = IP address mid low high byte

3 = IP address low byte

54

Group Name

EDID_FORMAT

EDID

EDID_RATE

EDID_REQUEST

AUDIO AUDIO_INPUT_MODE

Cmd Resp Description

EF EF

ER ER

ES ES

Af Af

EDID preferred format

EDID preferred frame frequency Rd/Wr 0

Request for an EDID

Audio mode

Read / Min

Write value

Rd/Wr 0

Max value

Default

Values value

21 0

0 = VGA

1 = 800x480

2 = WVGA

3 = SVGA

4 = 720pRGB

5 = XGA

6 = WXGA

7 = SWXGA

8 = 800pRGB

9 = 1152x864

10 = 900pRGB

11 = 1600x900

12 = 960pRGB

13 = SXGA

14 = 1360x1024

15 = SXGA+

16 = WSXGA+

17 = 1080pRGB

18 = 2K

19 = UXGA

20 = WUXGA

21 = Custom

Rd/Wr 0

Rd/Wr 0

5

2

1

0

0

1

Index #1

0 = Analog input

1

1 = Analog input

2

2 = Analog input8

3 = DVI-D input 1

4 = DVI-D input 2

0 = 50 Hz

1 = 60 Hz

2 = 72 Hz

3 = 75 Hz

4 = 85 Hz

5 = Custom

0 = EDID is ready

1 = EDID saving

2 = EDID reading

0 = Free choice of audio input

1 = Audio input follow the top layers

0 = Analog input

1

1 = Analog input

2

2 = Analog input8

3 = DVI-D input 1

4 = DVI-D input 2

0 = Analog input

1

1 = Analog input

2

2 = Analog input8

3 = DVI-D input 1

4 = DVI-D input 2

Index #2

55

Group Name

AUDIO_INPUT_MAP

AUDIO_LEVEL

AUDIO_AUX_LEVEL

AUDIO_BALANCE

AUDIO_AUX_BALANCE

AUDIO_MUTE

AUDIO_MASTER_VOLUME

Cmd Resp Description

Ai Ai Audio input map

AL AL Audio input level

Al Al Audio auxiliary input level

Ab Ab Audio input balance

AB AB Audio auxiliary input balance

Au Au Audio output Mute control

AV AV Output Master volume

Read / Min

Write value

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Max value

Default

Values value

12

255

255

90

90

1

255

1

45

45

45

45

0

255

0 = No input

1 = Input1

2 = Input2

3 = Input3

4 = Input4

5 = Input5

6 = Input6

7 = Input7

8 = Input8

9 = Input9

10 = Input10

11 = Input11

12 = Input12

Linear scale, init value is 0 dB

Linear scale, init value is 0 dB

0 = max to the left, 45 = centered,

90 = max to the right

0 = max to the left, 45 = centered,

90 = max to the right

1 = Mute.

0 = mute, 32 = -18dB , 255 = 0dB

Index #1

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Input1

1 = Input2

2 = Input3

3 = Input4

4 = Input5

5 = Input6

6 = Input7

7 = Input8

8 = Input9

9 = Input10

10 = Input11

11 = Input12

0 = Main output

1 = Preview output

0 = Main output

1 = Preview output

Index #2

56

Group Name

AUDIO_MODE

AUDIO_DELAY

AUDIO_AUTO_DELAY

AUDIO_SDI_CHAN_LEFT

AUDIO_SDI_CHAN_RIGHT

Cmd Resp Description

Am Am

AD AD

Ae

Ac

Ae

Ac

AC AC

Audio stero mode

Delay between audio and video

Automatic audio delay

ID of the Sdi channel to desembed for left channel

ID of the Sdi channel to desembed for right channel

Read / Min

Write value

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Max value

Default

Values value

1

80

1

15

15

1

0

1

0

1

0 = mono

1 = Stereo

0 = no delay

500ms = max delay

0 = réglage manuel du Delay, 1 = reglage automatique du delay

0 = Group A – Channel 1

1 = Group A – Channel 2

2 = Group A – Channel 3

3 = Group A – Channel 4

4 = Group B – Channel 1

5 = Group B – Channel 2

6 = Group B – Channel 3

7 = Group B – Channel 4

8 = Group C – Channel 1

9 = Group C – Channel 2

10 = Group C – Channel 3

11 = Group C – Channel 4

12 = Group D – Channel 1

13 = Group D – Channel 2

14 = Group D – Channel 3

15 = Group D – Channel 4

0 = Group A – Channel 1

1 = Group A – Channel 2

2 = Group A – Channel 3

3 = Group A – Channel 4

4 = Group B – Channel 1

5 = Group B – Channel 2

6 = Group B – Channel 3

7 = Group B – Channel 4

8 = Group C – Channel 1

9 = Group C – Channel 2

10 = Group C – Channel 3

11 = Group C – Channel 4

12 = Group D – Channel 1

13 = Group D – Channel 2

14 = Group D – Channel 3

15 = Group D – Channel 4

Index #1

0 = Main output

1 = Preview output

0 = Main output

1 = Preview output

10 = Channel 11

– SDI 1

11 = Channel 11

– SDI 2

12 = Channel 11

– SDI 3

13 = Channel 12

– SDI 4

10 = Channel 11

– SDI 1

11 = Channel 11

– SDI 2

12 = Channel 11

– SDI 3

13 = Channel 12

– SDI 4

Index #2

57

Group Name

AUDIO_DESEMBEND_LOCKED

Cmd Resp Description

Read / Min

Write value

Max value

Default

Values value

As As

Information of audio channel presence for SDI inputs

Rd 0 1 1 1 : Locked

RECORDING_MODE Rm Rm Video Output display mode

RECORDING

RECORDING_IMAGE_ADJUST_POS_H Rl Rl Horizontal position adjust

RECORDING_IMAGE_ADJUST_POS_V Rt Rt Vertical position adjust

RECORDING_IMAGE_ADJUST_SIZE_H Rw Rw Width adjust

RECORDING_IMAGE_ADJUST_SIZE_V Rh Rh Height adjust

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

Rd/Wr 0

1 0

0 = Output 1

1 = Output 2

255 128 128 = neutral

255 128 128 = neutral

255 128 128 = neutral

255 128 128 = neutral

Index #1

10 = Channel 11

– SDI 1

11 = Channel 11

– SDI 2

12 = Channel 11

– SDI 3

13 = Channel 12

– SDI 4

Index #2

58

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement