protech PROX-1750 User`s manual

protech PROX-1750 User`s manual
USER’S
MANUAL
ProX-1750
Pentium® 4/Pentium® 4-M
Motherboard
With VGA / Sound/ 2LAN
Prox-1750 M5
Copyright Notice
Prox-1750G1/G2 Pentium® 4/
Pentium®4-MMain Board
With VGA / SOUND / Dual LAN
OPERATION MANUAL
COPYRIGHT NOTICE
This operation manual is meant to assist both Embedded Computer
manufacturers and end users in installing and setting up the system. The
information contained in this document is subject to change without any
prior notice.
This manual is copyrighted February 2003. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical, including
photocopying and recording.
ACKNOWLEDGEMENTS
All trademarks and registered trademarks mentioned herein are the property
of their respective owners.
CE NOTICE
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Copyright Notice
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void your
authority to operate such equipment.
Contents
TABLE OF CONTENTS
CHAPTER
1-1
1-2
1-3
CHAPTER
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
2-12
2-13
2-14
2-15
2-16
2-17
2-18
2-19
2-20
2-21
2-22
2-23
2-24
2-25
2-26
2-27
2-28
2-29
2-30
1
INTRODUCTION
About This Manual .......................................................
System Specifications ...................................................
Safety Precautions .........................................................
2
1-2
1-3
1-6
HARDWARE CONFIGURATION
Jumper & Connector Quick Reference Table ...............
Component Locations ...................................................
How to Set the Jumpers ................................................
COM Port Connector …………………………………
RS232/422/485 (COM2) Selection ...............................
JCOM1 & COM2 (JCOM2) RI & Voltage Selection ...
COM3 & COM4 RI & Voltage Selection …………….
Keyboard & PS/2 Mouse Connector ………………….
Reset Connector ……………...……………………….
External Speaker Connector ……………..……………
Hard Disk Drive LED Connector .........................….....
Power LED Connector ………………………………..
EXTSIM# Connector.. ………………………………..
ATX Power Button ……………………………………
Keylock Connector ……………………………………
IrDA Connector …………...…………………………..
Printer Connector ...…...................................................
ATX Power Connector …………..................................
Clear CMOS Data Selection ..........................................
VGA Connector …………………...........................….
USB & LAN Connector …....................................……
USB Power Setting ……………………………………
LAN2 Enable/Disable Connector .................................
Wake-on-modem Connector ….....................……........
CPU Fan Connector …………..…................................
System Fan Connector ……..........................................
Reset/NMI/Clear Watchdog Selection ..........................
Hard Disk Drive Connector ……..................................
Floppy Disk Drive Connector …...................................
Sound Connector ...............……………........................
2-2
2-3
2-5
2-6
2-8
2-9
2-11
2-13
2-13
2-14
2-14
2-14
2-15
2-15
2-15
2-16
2-16
2-17
2-18
2-19
2-20
2-22
2-23
2-24
2-24
2-24
2-25
2-26
2-27
2-29
Contents
2-31
2-32
2-33
2-34
2-35
CD Audio-In Connector ……………............................
Memory Installation …………………………………..
PPCI Connector ...................……………......................
P4/P4-M CPU Selection ………………………………
EPPCI IRQ Selection …………………………………
CHAPTER
3-1
3-2
3-3
3-4
3-5
3-6
SOFTWARE UTILITIES
Introduction ...................................................................
VGA Driver Utility .......................................................
Flash BIOS Update .......................................................
LAN Driver Utility …....................................................
Sound Driver Utility …………………………………..
Watchdog Timer Configuration ....................................
CHAPTER
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-14
4-15
3
4
A
3-2
3-2
3-3
3-5
3-7
3-8
AWARD BIOS SETUP
Introduction ...................................................................
Entering Setup ...............................................................
The Standard CMOS Features ……..............................
The Advanced BIOS Features …...................................
Advanced Chipset Feature ............................................
Integrated Peripherals ……...........................................
Power Management Setup ............................................
PNP/PCI Configuration ….............................................
PC Health Status ……...................................................
Frequency / Voltage Control ….....................................
Load Fail-Safe Defaults ................................................
Load Optimized Defaults …..…………………………
Password Setting ……………………………………...
Save & Exit Setup .........................................................
Exit Without Saving ......................................................
APPENDIX
2-30
2-31
2-32
2-33
2-34
4-2
4-3
4-4
4-8
4-11
4-14
4-18
4-20
4-22
4-23
4-24
4-24
4-25
4-26
4-27
EXPANSION BUS
ISA Bus Pin Assignment ..........................................................
PCI Bus Pin Assignment ……………………………………..
A-2
A-3
Contents
APPENDIX
B
TECHNICAL SUMMARY
Block Diagram .........................................................................
Interrupt Map ............................................................................
RTC (Standard) RAM Bank .....................................................
Timer & DMA Channels Map ..................................................
I/O & Memory Map .................................................................
APPENDIX
C
B-2
B-3
B-4
B-5
B-6
TROUBLE SHOOTING
Trouble Shooting for Error Messages ......................................
Trouble Shooting for POST Codes ..........................................
C-2
C-8
CHAPTER
INTRODUCTION
1
This chapter gives you the information for Prox-1750G1/G2. It also
outlines the System specifications.
Section includes:
z About This Manual
z System Specifications
z Safety Precautions
Experienced users can skip to chapter 2 on page 2-1
for a Quick Start.
Page:1-1
Chapter
1
Introduction
1-1. ABOUT THIS MANUAL
Thank you for purchasing our Prox-1750G1/G2 Socket 478 Mainboard
enhanced with VGA/Sound/Dual LAN, which is fully PC / AT compatible.
The Prox-1750G1/G2 provides faster processing speed; greater
expandability and can handle more tasks than before. This manual is
designed to assist you how to install and set up the system. It contains four
chapters. The user can apply this manual for configuration according to the
following chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specifications for this system. The final page of this chapter will indicate
how to avoid damaging this board.
Chapter 2 Hardware Configuration
This chapter outlines the component locations and their functions. In the
end of this chapter, you will learn how to set jumper and how to configure
this card to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the
VGA utility, LAN utility, Sound utility, and Flash BIOS Update. It also
describes the Watchdog-timer configuration.
Chapter 4 Award BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A Expansion Bus
This Appendix introduces you the expansion bus for ISA BUS and PCI
BUS.
Appendix B Technical Summary
This section gives you the information about the Technical maps.
Appendix C Trouble Shooting
This section outlines the error messages and offers you the methods to
solve the problems.
Page: 1-2
Prox-1750G1/G2 USER′S MANUAL
Chapter
1
Introduction
1-2. SYSTEM SPECIFICATIONS
z CPU (mPGA478):
Prox-1750G1: Intel® Pentium® 4 processor in mPGA478 Socket.
Prox-1750G2: Intel® Pentium® 4 processor -M in mPGA478 Socket.
1.5~3.06 GHz clock generator.
Front Side Bus 533/400 MHZ.
Auto detect voltage regulator.
Intel 845G B version support H-T Tech.
z MEMORY :
Supports up to 2GB DDR SDRAM.
Two 184-pin DDR DIMM sockets on board.
z CACHE :
Built-in CPU.
z REAL-TIME CLOCK :
256-byte battery backed CMOS RAM.
Hardware implementation to indicate century rollover.
z BIOS :
Phoenix-AwardBIOS™ for plug & play function.
Easy update 512KB flash EEPROM.
Support S/IO Setup.
z KEYBOARD CONNECTOR :
Mini DIN connector.
Supports for AT/PS2 keyboard.
z MOUSE CONNECTOR :
Mini DIN connector.
Supports for PS/2 Mouse.
z BUS SUPPORT :
External 1 ISA, 6 PCI Bus
External 1 EPCI Bus
Prox-1750G1/G2 USER′S MANUAL
Page: 1-3
Chapter
1
Introduction
z DISPLAY :
Prox-1750G1 built in Intel® 845GE
Prox-1750G2 built in Intel® 845GV
Onboard 15-pin VGA D-SUB connector, support for resolution on SVGA
Monitor.
z WATCHDOG :
I / O port 0443H to Enable watchdog
I / O port 0441H to Disable watchdog
Selectable for NMI or Reset function by jumper setting
Time-out timing select 16 / 24 / 32 / 40 / 48 / 56 / 64 / 72 / 80 / 88 / 96 / 104 /
112 / 120 sec +/- 25%.
z IDE INTERFACE :
Two IDE ports support up to four IED devices.
Supports Ultra DMA 33/66/100.
z FLOPPY DISK DRIVER INTERFACE :
Support up to two Floppy Disk Drives, 3.5" and 5.25" (360K / 720K / 1.2M /
1.44M / 2.88M).
z USB CONNECTOR :
Three sets of USB connector & USB power (+5.0V/+5.0V Stand By)
selection.
Support up to six USB 2.0 ports.
z LAN ADAPTER :
Dual ports, Intel® 82562ET PHY & Intel® 82551QM or Intel 82540EM
(Giga Lan)
Two RJ-45 Jack onboard
LAN1: 10BaseT/100 BaseTx Ethernet
LAN2: 10/100 (82551QM) or 10/100/1000 (82540EM)
Support wake-on-LAN function.
z SERIAL PORT :
Four high speed 16550 Compatible UARTs with Send / Receive 16 Byte
FIFOs; COM1/3/4:RS-232; COM2:RS-232/422/485
MIDI Compatible
Programmable Baud Rate Generator
Page: 1-4
Prox-1750G1/G2 USER′S MANUAL
Chapter
1
Introduction
z SOUND :
Realtek ALC202A (AC’97 Codec).
Fully Compliant AC’97 Analog I/O Component
16-Bit Stereo Full-Duplex Codec
Four Analog Line-level Stereo Inputs for Connection.
High Quality CD Input with Ground Sense
Stereo Line-Level Output
Interface: Line-In, Line-Out, Microphone, and CD Audio-In.
z HARDWARE MONITORING FUNCTION :
Monitor Voltage, CPU temperature, & Cooling fan.
If CPU Temperature is over setting, the buzzer will send out a warming.
z IRDA PORT :
5-pin Infrared port, support IrDA v1.0 SIR protocol
z PARALLEL PORT :
SPP / ECP / EPP Function.
1 port, bi-directional parallel port.
z GREEN FUNCTION :
Software supported by BIOS setup
z LED INDICATOR :
System power
Hard Disk access
LAN LED indicator
z DMA CONTROLLER :
82C37 x 2
z DMA CHANNELS :
7
z INTERRUPT CONTROLLERS :
82C59 x 2
z INTERRUPT LEVELS :
15
Prox-1750G1/G2 USER′S MANUAL
Page: 1-5
Chapter
1
Introduction
z OPERATING TEMPERATURE :
0 to 60°C.
z BOARD DIMENSIONS :
305mm x 244mm, 12” x 9.61”
z BOARD NET WEIGHT :
0.67 Kg.
1-3. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Keep your system away from static electricity on all occasions.
2. Prevent electric shock. Don‘t touch any components of this card when the
card is power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance,
when you connect a jumper or install any cards, a surge of power may
damage the electronic components or the whole system.
Page: 1-6
Prox-1750G1/G2 USER′S MANUAL
HARDWARE
CONFIGURATION
CHAPTER
2
** QUICK START **
Helpful information describes the jumper & connector settings, and
component locations.
This section includes:
z Jumper & Connector Quick Reference Table
z Component Locations
z Configuration and Jumper settings
z Connector’s Pin Assignments
Page 2-1
Chapter
2
Hardware Configuration
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
COM Connector
….................................……...........
………………………………..…..
RS232/422/485 (COM2) Selection ......................….
COM1 & COM2 RI & Voltage Selection ………….
COM3 & COM4 RI & Voltage Selection ………….
Keyboard & PS/2 Mouse Connector ……………….
Reset Connector ...................................................….
External Speaker Connector ……….……………….
Hard Disk Drive LED Connector ........................…..
Power LED Connector ….................………………..
EXTSMI# Connector ….................…………………
ATX Power Button …………..……………………..
KEYLOCK ………………………………………….
IRDA Connector ……………………………………
Printer Connector .................................................….
ATX Power Connector ……………………………..
Clear CMOS Data Selection ………………………..
VGA Connector ..........................................………...
USB & LAN Connector ...........................…………..
Front USB Connector
...........................….………..
USB Power Setting ………………………………….
…………………………………
LAN2 Enable/Disable Selection ….………………...
Wake-On-Modem Connector ……………………….
CPU Fan Connector .............................................…..
System Fan Connector ………………………………
Reset/NMI/Clear Watchdog Selection ………………..
Hard Disk Drive Connector .................................…..
Floppy Disk Drive Connector ..............................…..
Sound Connector ..…………………………………..
CD Audio-In Connector ….…………………………
Memory Installation .............................................…..
PPCI Connector ……………………………………..
P4/P4-M CPU Selection …………………………….
EPPCI IRQ Selection ……………………………….
Reserved Pin ………………………………………...
Page: 2-2
JCOM1, COM2
COM3, COM4
JP3
JP4
JP1
JKBMS1
JPANEL1 (13, 15)
JPANEL1 (1, 3, 5, 7)
JPANEL1 (9, 11)
JPANEL1 (8, 10, 12)
JPANEL1 (2, 4)
JPANEL1 (14, 16)
JPANEL1 (17, 18)
IRDA1
JPRNT1
JATXPWR1, JATXPWR2
JCMOS1
JVGA1
JRJ45USB1, JRJ45USB2
JUSB3, JUSB2 (Optional)
JUSBV1, JUSBV2,
JUSBV3
JP6
WOL1 (JWOL1)
JCFAN1
JSFAN1, JSFAN2
JP2
IDE1, IDE2
FDD1
JAUDIO1
JCDIN1, JCDIN2
DDR1, DDR2
PPCI
JP11
JP10
JP5,JP7
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-2. COMPONENT LOCATIONS
Prox-1750G1 Connector, Jumper and Component locations
Prox-1750 USER'S MANUAL
Page: 2-3
Chapter
2
Hardware Configuration
Prox-1750G2 Connector, Jumper and Component locations
Page: 2-4
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting the jumpers. Jumper is consists of
two or three metal pins with a plastic base mounted on the card, and by
using a small plastic "cap", Also known as the jumper cap (with a metal
contact inside), you are able to connect the pins. So you can set-up your
hardware configuration by "opening" or "closing" pins.
The jumper can be combined into sets that called jumper blocks. When the
jumpers are all in the block, you have to put them together to set up the
hardware configuration. The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins (for example, labelled PIN1, PIN2, and PIN3),
You can connect PIN1 & PIN2 to create one setting and shorting. You can
either connect PIN2 & PIN3 to create another setting. The same jumper
diagrams are applied all through this manual. The figure below shows what
the manual diagram looks like and what they represent.
Prox-1750 USER'S MANUAL
Page: 2-5
Chapter
2
Hardware Configuration
JUMPER DIAGRAMS
JUMPER SETTINGS
Page: 2-6
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-4. COM PORT CONNECTOR
Four COM ports are enhanced in this board namely: JCOM1, COM2,
COM3 and COM4. JCOM1, COM3 and COM4 are fixed for RS-232
while COM2 is selectable for RS-232/422/485.
JCOM1 : COM1 Connector, DB9 male connector
The JCOM1 Connector assignments are as follows :
PIN
1
2
3
4
5
6
7
8
9
ASSIGNMENT
NDCD1
RXD1
TXD1
NDTR1
GND
NDSR1
NRTS1
NCTS1
NRI1
JCOM 1
COM2 : COM2 Connector
The COM2 Connector assignments are as follows :
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
RS-232
RS-422
RS-485
NDCD2
TXTXRXD2
TX+
TX+
TXD2
RX+
RX+
NDTR2
RXRXGND
GND
GND
NDSR2
RTSNC
NRTS2
RTS+
NC
NCTS2
CTS+
NC
NRI2
CTSNC
NC
NC
NC
Prox-1750 USER'S MANUAL
5
10
1
6
COM2
Page: 2-7
Chapter
2
Hardware Configuration
COM3 : COM3 Connector
The COM3 Connector assignments are as follows :
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
NDCD3
RXD3
TXD3
NDTR3
GND
NDSR3
NRTS3
NCTS3
NRI3
NC
6
1
10
5
COM3
COM4 : COM4 Connector
The COM4 Connector assignments are as follows :
PIN
1
2
3
4
5
6
7
8
9
10
Page: 2-8
ASSIGNMENT
NDCD4
RXD4
TXD4
NDTR4
GND
NDSR4
NRTS4
NCTS4
NRI4
NC
6
1
10
5
COM4
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-5. RS232/422/485 (COM2) SELECTION
JP3 : RS-232/422/485 Selection
COM1, COM3, & COM4 is fixed for RS-232 function only.
COM2 is selectable for RS-232, 422, 485 function.
The jumper settings are as follows :
COM 2
Function
Jumper Setting
(pin closed)
RS-232
Open
RS-422
1-2, 5-6, 7-8, 9-10
11-12,13-14,15-16
17-18, 19-20
RS-485
1-3, 4-6, 7-8, 9-10
11-12,13-14,15-16
17-18, 19-20
Jumper
Illustration
*** Manufactory default --- RS-232.
Prox-1750 USER'S MANUAL
Page: 2-9
Chapter
2
Hardware Configuration
2-6. JCOM1 & COM2(JCOM2) RI & VOLTAGE SELECTION
JP4: JCOM1 & COM2(JCOM2) RI & Voltage Selection
The selections are as follows:
COM PORT SELECTION
JUMPER
SETTINGS
JUMPER
ILLUSTRATION
2
1
RI
7-9
10
9
JP4
2
1
JCOM1
5V
1-3
10
9
JP4
2
1
12V
3-5
10
9
JP4
*** Manufactory default -- RI.
Page: 2-10
Prox-1750 USER'S MANUAL
Chapter
COM PORT SELECTION
JUMPER
SETTINGS
RI
2
Hardware Configuration
JUMPER
ILLUSTRATION
1
2
9
10
8-10
JP4
COM2
5V
1
2
9
10
2-4
(JCOM2)
JP4
2
1
12V
4-6
10
9
JP4
*** 1. Manufactory default – RI.
2. JCOM2 is shared with COM2.
Prox-1750 USER'S MANUAL
Page: 2-11
Chapter
2
Hardware Configuration
2-7. COM3 & COM4 RI & VOLTAGE SELECTION
JP1: COM3 & COM4 RI & Voltage Selection
The selections are as follows:
COM PORT SELECTION
RI
JUMPER
SETTINGS
JUMPER
ILLUSTRATION
1
2
9
10
7-9
JP1
COM3
5V
1
2
9
10
1-3
JP1
12V
1
2
9
10
3-5
JP1
*** Manufactory default -- RI.
Page: 2-12
Prox-1750 USER'S MANUAL
Chapter
COM PORT SELECTION
RI
JUMPER
SETTINGS
2
Hardware Configuration
JUMPER
ILLUSTRATION
1
2
9
10
8-10
JP1
COM4
5V
1
2
9
10
2-4
JP1
2
1
12V
4-6
10
9
JP1
*** Manufactory default -- RI.
Prox-1750 USER'S MANUAL
Page: 2-13
Chapter
2
Hardware Configuration
2-8. KEYBOARD & PS/2 MOUSE CONNECTOR
JKBMS1 : Keyboard & PS/2 Mouse Connector
The pin assignments are as follows :
PIN
1
2
3
4
5
6
7
8
9
10
11
12
ASSIGNMENT
L_KDAT
NC
GND
VCC
L_KCLK
NC
L_MDAT
NC
GND
VCC
L_MCLK
NC
9
8 7
6
5
3
4
2 1
JKBMS1
2-9. RESET CONNECTOR
JPANEL1 (13-15) : Reset Connector.
The pin assignments are as follows :
Reset
PIN
13
15
Page: 2-14
ASSIGNMENT
GND
RST_BUTT
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-10. EXTERNAL SPEAKER CONNECTOR
PIN
1
3
5
7
Speaker
JPANEL1 (1,3,5,7) : External Speaker Connector
The pin assignments are as follows :
ASSIGNMENT
SPK3
NC
NC
SPK VCC
2-11. HARD DISK DRIVE LED CONNECTOR
PIN
9
11
ASSIGNMENT
VCC3_3
HD_LED
HDD_LED
JPANEL1 (9-11) : Hard Disk Drive LED Connector
The pin assignments are as follows :
2-12. POWER LED CONNECTOR
JPANEL1 (8,10,12) : Power LED Connector
The pin assignments are as follows :
PIN
8
10
12
ASSIGNMENT
LED+
LED+
LED-
Prox-1750 USER'S MANUAL
Page: 2-15
Chapter
2
Hardware Configuration
2-13. EXTSMI# CONNECTOR
JPANEL1 (2,4) : EXTSMI# Connector
The pin assignments are as follows :
PIN
2
4
ASSIGNMENT
GPIO7
GND
2-14. ATX POWER BUTTON
JPANEL1 (14,16) : ATX Power Button
The pin assignments are as follows :
ATX-BTN
PIN
14
16
ASSIGNMENT
PW_BN1
PW_BN2
2-15. KEYLOCK CONNCETOR
JPANEL1 (19,20,21,22,23,24) : KEYLOCK Connector
The pin assignments are as follows :
Page: 2-16
ASSIGNMENT
KEYLOCK
GND
KEYLOCK
PIN
17
18
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-16. IRDA CONNECTOR
IRDA
JPANEL1 (19,20,21,22,23,24) : Infrared Connector.
Share with IRDA1.
The pin assignments are as follows :
PIN
ASSIGNMENT
19
GND
20
NC
21
VCC5
22
GND
23
IRTX2
24
IRRX2
2-17. PRINTER CONNECTOR
JPRNT1 : Printer Connector
The pin assignments are as follows :
JPRNT1
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
ASSIGNMENT
STB
P0
P1
P2
P3
P4
P5
P6
P7
ACK
BUSY
PE
SLCT
Prox-1750 USER'S MANUAL
PIN
14
15
16
17
18
19
20
21
22
23
24
25
ASSIGNMENT
AFD
ERR
INIT
SLIN
GND
GND
GND
GND
GND
GND
GND
GND
Page: 2-17
Chapter
2
Hardware Configuration
2-18. ATX POWER CONNECTOR
JATXPWR1 : ATX Power Connector
The pin assignments are as follows :
1
11
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Page: 2-18
10
JATXPWR1
20
ASSIGNMENT
+3.3V
+3.3V
GND
+5.0V
GND
+5.0V
GND
Power Good
+5.0V Standby
+12.0V
+3.3V
-12.0V
GND
Power On
GND
GND
GND
-5.0V
+5.0V
+5.0V
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
JATXPWR2 : ATX Power Connector
The pin assignments are as follows :
PIN
1
2
3
4
ASSIGNMENT
VCC12
VCC12
GND
GND
4
2
3
1
JATXPWR2
2-19. CLEAR CMOS DATA SELECTION
JCMOS1 : Clear CMOS Data Selection
The selection are as follows :
FUNCTION
JUMPER SETTING
(pin closed)
Normal
1-2
Clear CMOS
2-3
JUMPER
ILLUSTRATION
*** Manufacturing Default is set as Normal.
Note: To clear CMOS data, user must power-off the computer and set the
jumper to “Clear CMOS” as illustrated above. After five to six
seconds, set the jumper back to “Normal” and power-on the
computer.
Prox-1750 USER'S MANUAL
Page: 2-19
Chapter
2
Hardware Configuration
2-20. VGA CONNECTOR
JVGA1 : VGA Connector
The pin assignments are as follows:
5
10
15
1
6
11
JVGA1
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Page: 2-20
ASSIGNMENT
RED
GREEN
BLUE
NC
GND
GND
GND
GND
VGA_P5V
GND
NC
DDCDA
HSYNC
VSYNC
DDCLK
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-21. USB & LAN CONNECTOR
JRJ45USB1: USB & LAN Connector
This connector contains two USB ports and one LAN.
The pin assignments are as follows:
LAN
PIN
1
2
3
4
5
6
7
8
11
12
13
14
ASSIGNMENT
TX+
TXRX+
ISOLATED GND
ISOLATED GND
RXISOLATED GND
ISOLATED GND
Pull Hi
LED - Yellow
Pull Hi
LED - Green
USB
PIN
A1
A2
A3
A4
B1
B2
B3
B4
ASSIGNMENT
+5.0V or +5.0V Standby
USBP0−
USBP0+
GND
+5.0V or +5.0V Standby
USBP1−
USBP1+
GND
Prox-1750 USER'S MANUAL
Yellow
Green
JRJ45USB1
Page: 2-21
Chapter
2
Hardware Configuration
JRJ45USB2: USB & LAN Connector
This connector contains two USB ports and one LAN.
The pin assignments are as follows:
LAN
PIN
1
2
3
4
5
6
7
8
11
12
13
14
USB
PIN
A1
A2
A3
A4
B1
B2
B3
B4
ASSIGNMENT
INTEL82551QM
INTEL 82540
TX+
MDIO+
TXMDIORX+
MDI1+
ISOLATED GND
MDI1ISOLATED GND
MDI2+
RXMDI2ISOLATED GND
MDI3+
ISOLATED GND
MDI3Pull Hi
OrangeLED – Yellow
YellowPull Hi
Pull Hi
LED - Green
LED - Green
ASSIGNMENT
+5.0V or +5.0V STAND BY
USBP0−
USBP0+
GND
+5.0V or +5.0V STAND BY
USBP1−
USBP1+
GND
Yellow
Green
JRJ45USB2
(For INTEL 82551QM )
Yellow/Orange
Green
JRJ45USB2
(For INTEL 82540EM Giga Lan)
INTEL 82540 Giga Lan Selection
10 MB
No Display
100MB
Yellow Display
1000MB
Orange Display
A1
B1
A5
B5
JUSB2
Note: JUSB2 share the JRJ45USB2 for cable with rear USB bracket.
Page: 2-22
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
JUSB3: Front USB Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
+5.0V or +5.0V STAND BY
+5.0V or +5.0V STAND BY
USB_D4-USB_D5-USB_D4++
USB_D5++
GND
GND
NC
NC
1 2
10 9
JUSB3
2-22. USB POWER SETTING
JUSBV2: JRJ45USB1 POWER SELECTION
PIN
1
2
3
ASSIGNMENT
+5.0V
PIN#A1
PIN#B1
+5.0V STAND BY
1
JUSBV2
JUSBV1: JRJ45USB2 POWER SELECTION
PIN
1
2
3
ASSIGNMENT
+5.0V
PIN#A1
PIN#B1
+5.0V STAND BY
Prox-1750 USER'S MANUAL
1
JUSBV1
Page: 2-23
Chapter
2
Hardware Configuration
JUSBV3: JRJ45USB2 POWER SELECTION
PIN
1
2
3
1
ASSIGNMENT
+5.0V
USB_Power
+5.0V STAND BY
JUSBV3
2-23. LAN2 ENABLE / DISABLE SELECTION
JP6: LAN2 Enable / Disable Selection (for JRJ45USB2)
The selections are as follows:
SELECTION
JUMPER SETTINGS
(pins closed)
Enabled
1-2
Disabled
2-3
JUMPER
ILLUSTRATION
*** 1. Manufactory default --- Enabled.
2. LAN1 Enable/Disable Selection (for JRJ45USB1) by BIOS Setting.
Page: 2-24
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-24. WAKE-ON-MODEM CONNECTOR
WOL1 : Wake-On-Modem Connector
The pin assignments are as follows:
PIN
1
2
3
ASSIGNMENT
5V STANDBY
GND
ACTIVE SIGNAL
1
WOL1
2-25. CPU FAN CONNECTOR
JCFAN1 : CPU Fan connector
The pin assignments are as follows:
PIN
1
2
3
ASSIGNMENT
GND
+12V
FAN1
2-26. SYSTEM FAN CONNECTOR
JSFAN1 : System Fan connector
The pin assignments are as follows:
PIN
1
2
3
ASSIGNMENT
GND
+12V
FAN0
JSFAN2 : System Fan connector
The pin assignments are as follows:
PIN
1
2
3
ASSIGNMENT
GND
+12V
FAN2
Prox-1750 USER'S MANUAL
Page: 2-25
Chapter
2
Hardware Configuration
2-27. RESET/NMI/CLEAR WATCHDOG SELECTION
JP2 : Reset/NMI/Clear Watchdog Selection
The selections are as follows:
FUNCTION
JUMPER SETTING
(pin closed)
RESET
1-2
NMI
3-4
CLEAR WATCHDOG
5-6
JUMPER
ILLUSTRATION
***Manufacturing Default is set as NMI.
User may select to use the Reset or NMI watchdog. NMI, also known as NonMaskable Interrupt, is used for serious conditions that demand the processor’s
immediate attention; it cannot be ignored by the system unless it is shut off
specifically. To clear NMI command, user should short the “Clear Watchdog”
pin via push button.
Page: 2-26
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-28. HARD DISK DRIVE CONNECTOR
The Prox-1750 possesses two HDD connectors, IDE1 and IDE2.
IDE1: Hard Disk Drive Connector
The pin assignments are as follows:
2
40
1
39
IDE1
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
ASSIGNMENT
IDERST
GND
IDED7
IDED8
IDED6
IDED9
IDED5
IDED10
IDED4
IDED11
IDED3
IDED12
IDED2
IDED13
IDED1
IDED14
IDED0
IDED15
GND
NC
Prox-1750 USER'S MANUAL
PIN
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
ASSIGNMENT
IDEREQ
GND
IDEIOW
GND
IDEIOR
GND
IDE ORDY
GND
IDEACK
GND
IRQ14
NC
IDEA1
P66 DETECT
IDEA0
IDEA2
IDECS1P
IDECS3P
IDEACTP
GND
Page: 2-27
Chapter
2
Hardware Configuration
IDE2: Hard Disk Drive Connector
The pin assignments are as follows:
2
40
1
39
IDE2
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Page: 2-28
ASSIGNMENT
IDERST
GND
IDED7
IDED8
IDED6
IDED9
IDED5
IDED10
IDED4
IDED11
IDED3
IDED12
IDED2
IDED13
IDED1
IDED14
IDED0
IDED15
GND
NC
PIN
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
ASSIGNMENT
IDEREQ
GND
IDEIOW
GND
IDEIOR
GND
IDE ORDY
GND
IDEACK
GND
IRQ14
NC
IDEA1
S66 DETECT
IDEA0
IDEA2
IDECS1P
IDECS3P
IDEACTS
GND
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-29. FLOPPY DISK DRIVE CONNECTOR
FDD1 : Floppy Disk Drive Connector
You can use a 34-pin daisy-chain cable to connect two FDD. On one end of
this cable there is a 34-pin flat cable to attach the FDD on the board; the
other side is attaches to two FDD.
The pin assignments are as follows :
2
34
1
33
FDD1
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
ASSIGNMENT
GND
GND
NC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Prox-1750 USER'S MANUAL
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
ASSIGNMENT
DENSEL
NC
DENSEL1
INDEX
MOTEA
DRVB
DRVA
MOTEB
DIR
STEP
WDATA
WGATE
TK00
WPT
RDATA
SIDE1
DSKCHG
Page: 2-29
Chapter
2
Hardware Configuration
2-30. SOUND CONNECTOR
JAUDIO1 : Sound Connector, including Line-In, Line-Out & Mic. Also can
support only MIC connector. The pin assignments are as follows :
Page: 2-30
1
2
3
4
5
Mic-In
PIN
1
2
3
4
5
22
23
24
25
Line-Out
PIN ASSIGNMENT
22
SPK-L
23
NC
24
NC
25
SPK-R
32
33
34
35
Line-In
PIN ASSIGNMENT
32
LINE_L
33
AUD_GND
34
AUD_GND
35
LINE_R
Line-In
Line-Out
Mic-In
JAUDIO1
ASSIGNMENT
CGND
MIC_IN
CGND
NC
+5VAUDIO
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-31. CD AUDIO-IN CONNECTOR
JCDIN1 : CD Audio-in Connector
The pin assignments are as follows:
PIN
1
2
3
4
ASSIGNMENT
CDL
CD_GND
CDR
CD_GND
JCDIN1
JCDIN2 : CD Audio-in Connector
The pin assignments are as follows:
PIN
1
2
3
4
ASSIGNMENT
CDL
CD_GND
CD_GND
CDR
Prox-1750 USER'S MANUAL
1
JCDIN2
Page: 2-31
Chapter
2
Hardware Configuration
2-32. MEMORY INSTALLATION
The Prox-1750 embedded board supports two DDR memory sockets for a
maximum total memory of 2GB in DDR memory type. The memory module
capacities supported are 64MB, 128MB, 256MB, 512MB and 1GB. The
following table lists the supported DDR DIMM configurations. Intel 845G
supports configurations defined in the JEDEC DDR DIMM specification only
(A,B,C). Non-JEDEC standard DIMMs such as double-sided x 16 DDR
SDRAM DIMMs are not supported.
Supported DDR DIMM Configurations.
Density
64Mbit
128Mbit
Device X8
X16
X8
X16
Width
Single/ SS/DS SS/DS SS/DS SS/DS
Double
184-pin 64/128 32MB/ 128/25 64MB/
DDR
MB
NA
6MB NA
X8
256Mbit
X16
X8
512Mbit
X16
SS/DS SS/DS SS/DS SS/DS
256/51 128M
2MB B/NA
512/10 256M
24M
B/NA
Installing and Removing Memory Modules
To install the DDR modules, locate the memory slot on the embedded board
and perform the following steps:
1.
2.
3.
Page: 2-32
Hold the DDR module so that the key of the DDR module align with
those on the memory slot.
Gently push the DDR module in an upright position until the clips of
the slot close to hold the DDR module in place when the DDR module
touches the bottom of the slot.
To remove the DDR module, press the clips with both hands.
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-33. PPCI CONNECTOR
You will find a PPCI connector in our Prox-1750.
connect our SCSI daughter boards.
The pin assignments are as follows:
B30
PPCI
A30
PIN
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
0
ASSIGNMENT
GND
AD0
AD2
AD4
AD6
AD8
AD10
VCC
AD12
AD14
AD16
AD18
AD20
AD22
VCC
AD24
AD26
AD28
AD30
PIRQ#B
PP CLK
ID SEL
CBE#0
CBE#2
PGNT#3
SERR#
PIRQ#A
STOP#
DEVSEL#
GND
This connector is used to
B1
A1
PIN
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
ASSIGNMENT
GND
AD1
AD3
AD5
AD7
AD9
AD11
VCC
AD13
AD15
AD17
AD19
AD21
AD23
VCC
AD25
AD27
AD29
AD31
PAR
IRDY#
TRDY#
CBE#1
CBE#3
PREQ#3
PERR#
PCI_RST#
PLOCK#
FRAME#
GND
The PPCI expansion connector of this Card is designed based on PCI Bus Master.
That means when the PPCI expansion connector is used, the 4th PCI slot on the
backplane is occupied.
Prox-1750 USER'S MANUAL
Page: 2-33
Chapter
2
Hardware Configuration
2-34. P4/P4-M CPU SELECTION
JP11 : P4/P4-M CPU Selection. This jumper is for Prox-1750G2 only.
The selections are as follows:
Page: 2-34
FUNCTION
JUMPER SETTING
(pin closed)
P4-M
1-2
P4
Open
JUMPER
ILLUSTRATION
Please be aware that when using Pentium 4-M CPU, JP11 jumper must
set as closed, otherwise the P4-M CPU will be damaged, vice versa.
Prox-1750 USER'S MANUAL
Chapter
2
Hardware Configuration
2-35. EPPCI IRQ SELECTION
JP10 : EPPCI IRQ Selection. This jumper is for Prox-1750G2
only.
The selections are as follows:
FUNCTION
JUMPER SETTING
(pin closed)
PCI-IRQB
1-2
PCI-SERIRQ
2-3
JUMPER
ILLUSTRATION
** Manufacturing default: PCI-IRQB.
Prox-1750 USER'S MANUAL
Page: 2-35
SOFTWARE
UTILITIES
CHAPTER
3
This chapter comprises the detailed information of VGA driver,
LAN driver, Sound driver, and flash BIOS update. It also describes
on how to install the watchdog timer.
Section includes:
z VGA Driver Utility
z Flash BIOS Update
z LAN Driver Utility
z SOUND Driver Utility
z Watchdog Timer Configuration
Page: 3-1
Chapter
3
Software Configuration
3-1. INTRODUCTION
Enclosed with our Prox-1750G1/G2 package, you will find a CD ROM disk
containing all types of drivers we have. As a Prox-1750G1/G2 user, you
will only need the some of files contained in the CD ROM disk, please take
note of the following chart :
File name
Purpose
(Assume that CD ROM drive is D:)
D:\VGA\
For VGA driver installation
D:\Flash\Awdflash.exe
For BIOS update
D:\LAN\
For LAN Driver installation
D:\Sound\
For Sound driver installation
D:\Utility\Infinst_autol.exe
For Intel® Chipset Software
Installation Utility
***Install this software first!
Software Update 95/98/98SE/2K.
3-2. VGA DRIVER UTILITY
The VGA interface is embedded with our Prox-1750G1/G2 system to support
CRT display, Panel Link and TV-Out Encoder. The following illustration
briefly shows you the content of VGA driver in D:\VGA\:
1. Win 9x program
2. WinNT4.0 program
3. Win 2000 program
Page:3-2
Prox-1750G1/G2 USER′S MANUAL
Chapter
3
Software Configuration
3-2-1. Installation of VGA Driver
(1) Start the computer (Win 9x/NT/2K).
(2) Insert the Utility Disk into the CD ROM drive or drive A/B.
(3) Double-click “D:\VGA\WIN9X\SETUP.EXE
(if D is not your CD ROM drive and substitute D with the right drive) in
the text entry area and press OK.
(4) Click “Next” on the Welcome screen.
(5) Read the license agreement and click “Yes” to continue.
(6) The driver files will now be installed. When finished, choose the
“Yes” to reboot option, and click “Finished” to restart your computer.
The driver should now be loaded.
For more information on VGA driver installation, please refer to the
readme.txt found on the sub-directory of the VGA driver utility.
3-3. FLASH BIOS UPDATE
3-3-1. System BIOS Update:
Users of Prox-1750G1/G2 can use the program “Awdflash.exe” contained
in CD ROM for BIOS update. This is found in D:\flash\Awdflash.exe.
3-3-2. To update BIOS :
(1) Install “Awdflash.exe” from the CD ROM Disk into your system.
(2) Insert the new BIOS file you have obtained from Prox-1750G1/G2
vendor.
(3) Type the pathname to Awdflash.exe and execute the BIOS update with
file b55xxxxx.bin
C:\UTIL\AWDFLASH\AWARDFLASH
H50xxxxx.bin
(4) The screen will display the table below:
FLASH MEMORY WRITER v7.xx
( C ) Award Software 2000 All Rights Reserved
For i845-ITE8712-6A69RP69C-0
DATE : 05/06/01
Flash Type - SST 49LF004A /3.3V
File Name to Program : B55xxxxx.bin
Checksum : XXXXX
Error Message :
Do You Want To Save BIOS (Y/N)
Prox-1750G1/G2 USER′S MANUAL
Page:3-3
Chapter
3
Software Configuration
If you want to save up the original BIOS, enter “Y ”and press < Enter > .
If you choose “N”, the following table will appear on screen.
FLASH MEMORY WRITER v7.xx
( C ) Award Software 2000 All Rights Reserved
For i845-ITE8712-6A69RP69C-0
DATE : 05/06/01
Flash Type - SSL 49LF004A /3.3V
File Name to Program : H50xxxxx.bin
Checksum : XXXXX
Error Message :
Are You Sure To Program (Y/N)
Select “Y”, and the BIOS will be renewed. When you are refreshing your
BIOS, do not turn off or reset the system, or you will damage the BIOS.
After you have completed all the programming, you will see the line:
“Reset System or power off to accomplish update process!”. Please turn off
or reset the system. Then the Flash BIOS is fully implemented.
Page:3-4
Prox-1750G1/G2 USER′S MANUAL
Chapter
3
Software Configuration
3-4. LAN DRIVER UTILITY
3-4-1. Introduction
The Prox-1750G1/G2 Mainboard is enhanced with LAN function that
can support various network adapters. The content of the LAN driver
is found as follows :
1. Windows 9x
2. Windows NT
3. Windows 2000
4. Netware
5. DOS
6. OS2
7. Linux
8. Unix
3-4-2. Installation Procedure for Windows 9x
(1) Insert the LAN Driver disk into Drive A or CD ROM drive.
(2) In the “My computer”, select the “Control Panel” icon.
(3) In the “Control Panel” windows, select the “System” icon.
(4) The “System Properties” window will appear, select the “Device
Manager” and look for the “Network Adapter – PCI Fast Ethernet
Adapter”.
(5) Click “Properties” and then “PCI Fast Ethernet Adapter Properties”,
choose the “Driver” icon.
(6) Click “Update Driver” icon, and follow the remaining instruction.
Prox-1750G1/G2 USER′S MANUAL
Page:3-5
Chapter
3
Software Configuration
3-4-3. Installation Procedure for Windows NT
1. In the Main group to NT, select the “Control Panel” icon.
2. In the Control Panel window, choose the “Network” icon.
3. In the Network Settings dialog box, choose the “Add adapter” button.
The Add Network Adapter dialog box appears.
4. In the list of network cards, select “<Other> requires disk from
manufacturer”, and then press <Enter> button.
5. Insert the LAN Driver disk in Drive A or CDROM drive, and type
D:\LAN, and then choose OK button.
6. Follow the remaining instruction, and re-boot your system to complete
the installation process.
Page:3-6
Prox-1750G1/G2 USER′S MANUAL
Chapter
3
Software Configuration
3-5. SOUND DRIVER UTILITY
3-5-1. Introduction
The ALC201A sound function enhanced in this system is fully
compatible with Windows 98, Windows NT 4.0, Windows 2000 and
Windows XP. Below, you will find the content of the Sound driver :
1. Win 98 program
2. Win NT 4.0 program
3. Win 2000 program
4. Win XP Program
3-5-2. Installation Procedure for Windows 9x/NT/2000
(1) From the task bar, click on Start, and then Run.
(2) In the Run dialog box, type D:\Sound\path\setup, where
“D:\Sound\path” refers to the full path to the source files.
(3) Click on the OK button or press the ENTER key.
(4) Click on the “Next” and OK prompts as they appear.
(5) Reboot the system to complete the driver installation.
Prox-1750G1/G2 USER′S MANUAL
Page:3-7
Chapter
3
Software Configuration
3-6. WATCHDOG TIMER CONFIGURATION
This board has watchdog timer function for monitoring whether the system
is still work or not after a period of time. The user can select watchdog
timer to system reset or NMI (Non Maskable interrupt) depending on the
jumper set in “Reset/NMI/Clear Watchdog Selection” as described in
chapter 2. This is defined at I/O port 443H. When you want to enable the
watchdog timer, please write I/O port 443H, then the system will either
reset itself or perform the NMI function. Likewise, when you want to
disable the function, write I/O port 441H, the system will run the command
to stop the Watchdog function.
In Prox-1750G1/G2 watchdog function, You must write your program so
when it writes I/O port address 443 for enable watchdog and write I/O port
address 441 for disable watchdog. The timer's intervals have a tolerance of
25% so you should program an instruction that will refresh the timer about
every second.
The following program shows you how to program the watch timer in your
program.
Watchdog enable program:
MOV
AX, 000FH
(choose the values you need; start from 0)
MOV
DX, 0443H
OUT
DX, AX
Watchdog disable program:
MOV
AX, 000FH
(this value can be ignored)
MOV
DX, 0441H
OUT
DX, AX
The Watchdog Timer control table is as follows:
Level
Value
Time/sec
Level
Value
1
2
3
4
5
6
7
8
F
E
D
C
B
A
9
8
0
8
16
24
32
40
48
56
9
10
11
12
13
14
15
16
7
6
5
4
3
2
1
0
Page:3-8
Time/sec
64
72
80
88
96
104
112
120
Prox-1750G1/G2 USER′S MANUAL
CHAPTER
AWARD
BIOS SETUP
4
This chapter shows how to set up the Award BIOS.
Section includes:
z Introduction
z Entering Setup
z The Standard CMOS Features
z The Advanced BIOS Features
z The Advanced Chipset Features
z Integrated Peripherals
z Power Management Setup
z PnP/PCI Configurations
z PC Health Status
z Frequency/Voltage Control
z Load Fail-Safe Defaults
z Password Setting
z Save and Exit Setup
z Exit Without Saving
Page: 4-1
Chapter
4
Award BIOS Setup
4-1. INTRODUCTION
This chapter will show you the function of the BIOS in managing the features
of your system. The Prox-1750G1/G2 Socket 370 Mainboard is equipped with
the BIOS for system chipset from Award Software Inc. This page briefly
explains the function of the BIOS in managing the special features of your
system. The following pages describe how to use the BIOS for system chipset
Setup menu.
Your application programs (such as word processing, spreadsheets, and games)
rely on an operating system such as DOS or OS/2 to manage such things as
keyboard, monitor, disk drives, and memory.
The operating system relies on the BIOS (Basic Input and Output system), a
program stored on a ROM (Read-only Memory) chip, to initialize and
configure your computer's hardware. As the interface between the hardware
and the operating system, the BIOS enables you to make basic changes to
your system's hardware without having to write a new operating system.
The following diagram illustrates the interlocking relationships between the
system hardware, BIOS, operating system, and application program:
Page: 4-2
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
4-2. ENTERING SETUP
When the system is powered on, the BIOS will enter the Power-On Self
Test (POST) routines and the following message will appear on the lower
screen:
PRESS <DEL> TO ENTER SETUP, ESC TO SKIP MEMORY TEST
As long as this message is present on the screen you may press the <Del>
key (the one that shares the decimal point at the bottom of the number
keypad) to access the Setup program. In a moment, the main menu of the
Award Setup Program will appear on the screen:
Phoenix - AwardBIOS CMOS Setup Utility
▶Standard CMOS Features
▶Frequency/Voltage Control
▶Advanced BIOS Features
Load Fail-Safe Defaults
▶Advanced Chipset Features
Load Optimized Defaults
▶Integrated Peripherals
Set Supervisor Password
▶Power Management Setup
Set User Password
▶PnP/PCI Configurations
Save & Exit Setup
▶PC Health Status
Exit Without Saving
↑↓→← : Select Item
Esc : Quit
F10 : Save & Exit Setup
Time, Date, Hard Disk Type . . .
Setup program initial screen
You may use the cursor the up/down keys to highlight the individual menu
items. As you highlight each item, a brief description of the highlighted
selection will appear at the bottom of the screen.
Prox-1750G1/G2 USER′S MANUAL
Page: 4-3
Chapter
4
Award BIOS Setup
4-3. THE STANDARD CMOS FEATURES
Highlight the〝STANDARD CMOS FEATURES〞and press the <ENTER>
key and the screen will display the following table:
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
▶
▶
▶
▶
Date (mm:dd:yy)
Time (hh:mm:ss)
Wed, Aug 7 2002
10 : 50 : 17
IDE Primary Master
IDE Primary Slave
IDE Secondary Master
IDE Secondary Slave
[None]
[IBM-DHEA-36481]
[None]
[CD-540E]
Drive A
Drive B
[1.44M, 3.5 in.]
[None]
Video
Halt On
[EGA/VGA]
[All, But Keyboard]
Base Memory
Extended Memory
Total Memory
640K
129024K
130048K
Item Help
Menu Level
▶
Change the day, month,
year and century
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Standard CMOS Setup Screen
In the above Setup Menu, use the arrow keys to highlight the item and then use
the <PgUp> or <PgDn> keys to select the value you want in each item. Note
that as you highlight each item, the description of the selected item is found on
the right side of the screen.
Date:
< Month >, < Date > and <Year >. Ranges for each value are in the CMOS
Setup Screen, and the week-day will skip automatically.
Time:
< Hour >, < Minute >, and < Second >. Use 24 hour clock format, i.e., for PM
numbers, add 12 to the hour. For example: 4: 30 P.M. You should enter the
time as 16:30:00.
Page: 4-4
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
IDE Primary Master / Slave:
IDE Secondary Master / Slave:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix - AwardBIOS CMOS Setup Utility
IDE Primary Master
IDE HDD Auto-Detection
[Press Enter]
IDE Primary Master
Access Mode
[Auto]
[Auto]
Menu Level
Capacity
37511 MB
Cylinder
Head
Precomp
Landing Zone
Sector
17956
16
65535
17955
255
To auto-detect the
HDD’s size, head…on
this channel
Item Help
▶▶
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Table 1 – IDE Primary Master sub menu
Descriptions on each item above are as follows:
1. IDE HDD Auto-detection
Press the enter key to auto-detect the HDD on this channel. If detection
is successful, it fills the remaining fields on this menu.
2. IDE Primary Master
There are three available option on this category, namely: None, Auto,
and Manual. By selecting “Manual”, you can set the remaining fields
on this screen, such as a. Cylinder – Set the number of cylinders for this hard disk.
b. Head – Set the number of read/write heads.
c. Precomp - ***Warning! Setting a value of 65535 means no HDD.
d. Landing Zone
e. Sector – Set the number of sector per track
Prox-1750G1/G2 USER′S MANUAL
Page: 4-5
Chapter
4
Award BIOS Setup
3. Access Mode
There are four available options for this item, namely: Normal, LBA,
Large and Auto. Choose the access mode for this hard disk.
4. Capacity
Disk Drive capacity (Approximated). Note that this size is usually
slightly greater than the size of a formatted disk given by a diskchecking program.
DRIVE A AND DRIVE B:
Select the type of floppy disk drive installed in your system. The available
options are 360KB 5.25in, 1.2KB 5.25in, 720KB 3.5in, 1.44MB 3.5in,
2.88MB 3.5in and None.
VIDEO:
This category selects the type of video adapter used for the primary system
monitor. Although secondary monitors are supported, you do not have to
select the type in Setup. Available Options are Mono, Color 40,
VGA/EGA, and Color 80.
EGA/VGA
Enhanced Graphics Adapter/Video Graphics Array.
For EGA, VGA, SEGA, SVGA or PGA monitor
adapters.
CGA 40
Color Graphics Adapter, power up in 40 column mode.
CGA 80
Color Graphics Adapter, power up in 80 column mode.
MONO
Monochrome adapter, includes high resolution
monochrome adapters.
HALT ON:
This category allows user to choose whether the computer will stop if an error
is detected during power up. Available options are “All errors”, “No errors”,
“All, But keyboard”, “All, But Diskette”, and “All But Disk/Key”.
BASE MEMORY:
Displays the amount of conventional memory detected during boot up.
EXTENDED MEMORY:
Displays the amount of extended memory detected during boot up.
TOTAL MEMORY:
Displays the total memory available in the system.
Page: 4-6
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
HARD DISK ATTRIBUTES:
Type
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
47
Cylinders
306
615
615
940
940
615
642
733
900
820
855
855
306
733
000
612
977
977
1024
733
733
733
306
977
1024
1224
1224
1224
1024
1024
918
925
1024
1024
1024
1024
1024
1024
918
820
1024
1024
809
809
776
Heads
4
4
6
8
6
4
8
5
15
3
5
7
8
7
0
4
5
7
7
5
7
5
4
5
9
7
11
15
8
11
11
9
10
12
13
14
2
16
15
6
5
5
6
6
8
V-P comp
128
300
300
512
512
65535
256
65535
65535
65535
65535
65535
128
65535
0000
0000
300
65535
512
300
300
300
0000
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65335
AUTO
LZone
305
615
615
940
940
615
511
733
901
820
855
855
319
733
000
663
977
977
1023
732
732
733
336
976
1023
1223
1223
1223
1023
1023
1023
926
1023
1023
1023
1023
1023
1023
1023
820
1023
1023
852
852
775
Sect
17
17
17
17
17
17
17
17
17
17
17
17
17
17
00
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
26
17
26
33
Capacity
10
20
30
62
46
20
30
30
112
20
35
49
20
42
00
20
40
56
59
30
42
30
10
40
76
71
111
152
68
93
83
69
85
102
110
119
17
136
114
40
42
65
40
61
100
Award Hard Disk Type Table
Prox-1750G1/G2 USER′S MANUAL
Page: 4-7
Chapter
4
Award BIOS Setup
4-4. THE ADVANCED BIOS FEATURES
Choose the〝ADVANCED BIOS FEATURES〞in the main menu, the screen
shown as below.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
Virus Warning
CPU Internal Cache
External Cache
CPU L2 Cache ECC Checking
Processor Number Feature
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
Typematic Rate Setting
x Typematic Rate (Chars/Sec)
x Typematic Delay (Msec)
Security Option
OS Select For DRAM > 64MB
HDD S.M.A.R.T. Capability
Report No FDD for WIN 95
Small Logo (EPA) Show
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Floppy]
[HDD-0]
[LS120]
[Enabled]
[Disabled]
[Enabled]
[On]
[Fast]
[Disabled]
6
250
[Setup]
[Non-OS2]
[Disabled]
[No]
[Disabled]
Item Help
Menu Level
▶
Allows you to choose
the VIRUS warning
feature for IDE Hard
Disk boot sector
protection. If this
function is enabled and
someone attempt to
write data into this area,
BIOS will show a
warning message on
screen and alarm beep
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Advanced BIOS Features Setup Screen
The “ADVANCED BIOS FEATURES SETUP” allow you to configure your
system for basic operation. The user can select the system’s default speed,
boot-up sequence, keyboard operation, shadowing and security.
Page: 4-8
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
A brief introduction of each setting in the BIOS FEATURES SETUP
program is given below.
VIRUS WARNING :
This item allows you to choose the Virus Warning feature for IDE Hard Disk
boot sector protection. When this function is enabled, the BIOS will
supervise the boot sector and partition table of the hard disk drive for any
attempt for modification.
CPU INTERNAL CACHE/EXTERNAL CACHE :
These two categories speed up memory access. However, it depends on
CPU/chipset design.
CPU L2 CACHE ECC CHECKING :
This item allows you to enable or disable CPU L2 Cache ECC checking.
PROCESSOR NUMBER FEATURE :
This option is for Pentium III processor only. During Enabled, this will check
the CPU Serial number. Disabled this option if you don’t want the system to
know the Serial number.
QUICK POWER ON SELF TEST:
This item allows you to speed up Power On Self Test (POST) after power-up
the computer. When enabled, the BIOS will shorten or skip some check items
during POST.
FIRST/SECOND/THIRD/OTHER BOOT DEVICE:
The BIOS load the operating system in a sequence selected by these items.
SWAP FLOOPY DRIVE:
This field is effective only in systems with two floppy drives. Selecting
Enabled assigns physical drive B to logical drive A, and physical drive A to
logical drive B.
BOOT UP FLOPPY SEEK:
You may enable / disable this item to define whether the system will look for
a floppy disk drive to boot at power-on, or proceed directly to the hard disk
drive.
Prox-1750G1/G2 USER′S MANUAL
Page: 4-9
Chapter
4
Award BIOS Setup
BOOT UP NUMLOCK STATUS:
Select power on state for NumLock.
GATE 20A OPTION:
This entry allows you to select how the gate A20 is handled. When Normal
was set, a pin in the keyboard controller controls Gate A20. And when Fast
was set, the chipset controls Gate A20.
TYPEMATIC RATE SETTING:
Enable this item if you wish to be able to configure the characteristics of
your keyboard. Typematic refers to the way in which characters are entered
repeatedly if a key is held down. For example, if you press and hold down
the "A" key, the letter "a" will repeatedly appear on your screen on your
screen until you release the key. When enabled, the typematic rate and
typematic delay can be selected.
TYPEMATIC RATE (CHARS/SEC):
This item sets the number of times a second to repeat a key stroke when you
hold the key down. The choices are 6, 8, 10, 12, 15, 20, 24, and 30.
TYPEMATIC DELAY (MSEC):
The item sets the delay time after the key is held down before it begins to
repeat the keystroke. The choices are 250, 500, 750, and 1000.
SECURITY OPTION:
This category allows you to limit access to the system and Setup, or just to
Setup.
System
The system will not boot and access to Setup will be
denied if the correct password is not entered at the
prompt.
Setup
The system will boot, but access to Setup will be
denied if the correct password is not entered at the
prompt.
To disable security, select PASSWORD SETTING at Main Menu and
then you will be asked to enter password. Do not type anything and just
press <Enter>, it will disable security. Once the security is disabled, the
system will boot and you can enter Setup freely.
Page: 4-10
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
OS SELECT FOR DRAM >64MB :
Select the operating system that is running with greater than 64MB or RAM
on the system. You may choose OS2 or Non-OS2.
REPORT NO FDD FOR WIN 95 :
Select Yes to release IRQ6 when the system contains no floppy drive, for
compatibility with Windows 95 logo certification. In the Integrated
Peripherals screen, select Disabled for the Onboard FDC Controller field.
4-5. ADVANCED CHIPSET FEATURES
Choose the〝ADVANCED CHIPSET FEATURES〞from the main menu,
the screen shown as below.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing Selectable
[By SPD]
CAS Latency Time
Active to Precharge Delay
DRAM RAS-to-CAS Delay
DRAM RAS Precharge
Turbo Mode
Memory Frequency For
System BIOS Cacheable
Video BIOS Cacheable
Memory Hole At 15M-16M
Delayed Transaction
AGP Aperture Size
[2.5]
[6]
[3]
[3]
[Disabled]
[Auto]
[Enabled]
[Disabled]
[Disabled]
[Enabled]
[64MB]
** On-Chip VGA Setting **
On-Chip VGA
On-Chip Frame Buffer Size
I/O Channel Check NMI
[Enabled]
[8MB]
[Disabled]
Item Help
Menu Level
▶
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Advanced Chipset Features Setup
Prox-1750G1/G2 USER′S MANUAL
Page: 4-11
Chapter
4
Award BIOS Setup
The parameters in this setup screen are for system designers, service
personnel, and technically competent users only. Do not reset these values
unless you understand the consequences of your changes.
DRAM TIMEING SELECTABLE:
The value in this field depends on performance parameters of the installed
memory chips (DRAM). Do not change the value from the factory setting
unless you install new memory that has a different performance rating than
the original DRAMs.
CAS LATENCY TIME:
When synchronous DRAM is installed, the number of clock cycles of CAS
latency depends on the DRAM timing.
DRAM RAS-TO-CAS DELAY:
This item let you insert a timing delay between the CAS and RAS strobe
signals, used when DRAM is written to, read from, or refreshed. Fast
gives faster performance; and Slow gives more stable performance. This
field applies only when synchronous DRAM is installed in the system.
The choices are 2 and 3.
DRAM RAS PRECHARGE TIME:
If an insufficient number of cycles is allowed for the RAS to accumulate its
charge before DRAM refresh, the refresh may be incomplete and the DRAM
may fail to retain data. Fast gives faster performance; and Slow gives more
stable performance. This field applies only when synchronous DRAM is
installed in the system. The choices are 2 & 3.
SYSTEM BIOS CACHEABLE:
This item allows you to enable caching of the system BIOS ROM at F0000hFFFFFh, resulting in better system performance. However, if any program
writes to this memory area, a system error may result.
VIDEO BIOS CACHEABLE:
This item allows you to enable caching of the video BIOS, resulting in better
system performance. However, if any program writes to this memory area,
a system error may result.
Page: 4-12
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
MEMORY HOLE AT 15M-16M:
You may reserve this area of system memory for ISA adapter ROM. When
this area is reserved, it cannot be cached. The user information of
peripherals that need to use this area of system memory usually discusses
their memory requirements.
DELAY TRANSACTION:
The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select Enabled to support compliance with PCI
specification version 2.1.
AGP APERTURE SIZE:
The aperture is a portion of the PCI memory address range dedicated for
graphics memory address space. Host cycles that hit the aperture range are
forwarded to the AGP without any translation.
ON-CHIP Frame Buffer SIZE:
Select the on-chip frame buffer size for VGA drive use. The available
choices are 8MB, and Disabled.
IO CHANNEL CHECK NMI:
This field enable or disable IO channel check NMI. Before selecting this
function, the user should check first that NMI function is enabled as
described in chapter 2 (Reset/NMI/Clear Watchdog Selection)
Prox-1750G1/G2 USER′S MANUAL
Page: 4-13
Chapter
4
Award BIOS Setup
4-6. INTEGRATED PERIPHERALS
Choose〝INTEGRATED PERIPHERALS〞from the main setup menu, a
display will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
On-Chip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-Chip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
USB Controller
USB 2.0 Controller
USB Keyboard Support
USB Mouse Support
AC97 Audio
Onboard/CNR LAN selection
Init Display First
BIOS Flash Function
IDE HDD Block Mode
POWER ON Function
x KB Power ON Password
x Hot Key Power ON
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
x RxD, TxD Active
x IR Transmission Delay
x UR2 Duplex Mode
x Use IR Pins
Onboard Parallel Port
Parallel Port Mode
x EPP Mode Select
x ECP Mode Use DMA
PWRON After PWR-Fail
Onboard Serial Port 3
Serial Port 3 Use IRQ
Onboard Serial Port 4
Serial Port 4 Use IRQ
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Auto]
[Auto]
[Onboard/AGP]
[Enabled]
[Enabled]
[BUTTON ONLY]
[Enter]
[Ctrl-F1]
[Enabled]
[3F8/IRQ4]
[2F8/IRQ3]
[Normal]
[Hi, Lo]
[Enabled]
Half
IR-Rx2Tx2
[378/IRQ7]
[SPP]
EPP1.7
3
[Off]
[3E8]
[IRQ10]
[2E8]
[IRQ11]
Item Help
Menu Level ▶
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
INTEGRATED PERIPHERALS
Page: 4-14
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
By moving the cursor to the desired selection and pressing <F1> key, the
all options for the desired selection will be displayed for choice.
ON-CHIP PRIMARY PCI IDE
ON-CHIP SECONDARY PCI IDE:
The Integrated peripheral controller contains an IDE interface with support for
two IDE channels. Select Enabled to activate each channel separately.
IDE PRIMARY MASTER/SLAVE PIO:
IDE SECONDARY MASTER/SLAVE PIO:
The four IDE PIO fields allow you to set a PIO mode (0-4) for each of the
four IDE devices that the onboard IDE interface supports. Modes 0 through
4 provide successively increased performance. In Auto mode, the system
automatically determines the best mode for each device.
IDE PRIMARY MASTER/SLAVE UDMA:
IDE SECONDARY MASTER/SLAVE UDMA:
UDMA (Ultra DMA) is a DMA data transfer protocol, that utilizes ATA
commands and the ATA bus to allow DMA commands to transfer data at a
maximum burst rate of 33 MB/s. The implementation of UDMA is possible
only if your IDE hard drive supports it and the operating environ-ment
includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master
driver). If you hard drive and your system software both support Ultra
DMA/33, select Auto to enable BIOS support.
USB CONTROLLER:
Select enabled if the system contains a Universal Serial Bus (USB) controller
and you have USB peripherals.
USB KEYBOARD SUPPORT:
Select enabled if the system contains a Universal Serial Bus (USB) controller
and you have a USB Keyboard.
USB MOUSE SUPPORT:
Select enabled if the system contains a Universal Serial Bus (USB) controller
and you have a USB Mouse.
INIT DISPLAY FIRST:
This item allows you to decide to active whether PCI Slot or on-chip VGA
first.
Prox-1750G1/G2 USER′S MANUAL
Page: 4-15
Chapter
4
Award BIOS Setup
AC97 AUDIO:
This item allows you to decide to enable or disable the 810 chipset family to
support AC97 Audio.
IDE HDD BLOCK MODE:
Block mode is also called block transfer, multiple commands, or multiple
sector read/write. If your IDE hard drive supports block mode (most new
drives do), select Enabled for automatic detection of the optimal number of
block read/writes per sector the drive can support.
ONBOARD FDC CONTROLLER:
Select Enabled if the system has a floppy disk controller (FDC) installed on
the system board and you wish to use it. If you install and-in FDC or the
system has no floppy drive, select Disabled.
ONBOARD SERIAL PORT 1
ONBOARD SERIAL PORT 2:
Select an address and corresponding interrupt for the first and second serial
ports.
UART MODE SELECT:
Select an operating mode for the second serial port. The choices are IrDA,
Normal and ASK IR.
RxD, TxD ACTIVE:
Consult your IR peripheral documentation to select the correct setting of the
TxD and RxD signals.
UR2 DUPLEX MODE:
This item allows you to select the IR half/full duplex function.
ONBOARD PARALLEL PORT:
This field determine access onboard parallel port controller with which I/O
address.
PARALLEL PORT MODE:
Select an operating mode for the onboard parallel port. The available
choices are SPP, EPP, ECP, or ECP+EPA modes.
Page: 4-16
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
EPP MODE SELECT:
This item allows you to configure the parallel port for the selected EPP
mode. The Selection of EPP port type is 1.7 or 1.9.
ECP MODE USE DMA:
This item allows you to configure the parallel port DMA channel for the
selected ECP mode. This selection is only available when ECP or
ECP+EPP is selected in Parallel Port mode.
PWRON AFTER PWR-FAIL:
This item allows you to select if you want to power on the system after
power failure.
ONBOARD SERIAL PORT 3:
ONBOARD SERIAL PORT 4:
Select a logical COM port name and matching address for the third and
forth serial ports. Select an address and corresponding interrupt for third
and forth serial port.
SERIAL PORT 3 USE IRQ:
SERIAL PORT 4 USE IRQ:
The items set the IRQ address of the serial ports.
Prox-1750G1/G2 USER′S MANUAL
Page: 4-17
Chapter
4
Award BIOS Setup
4-7. POWER MANAGEMENT SETUP
Choose〝POWER MANAGEMENT SETUP〞option on the main menu, a
display will be shown on screen as below :
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
ACPI Function
Power Management
MODEM Use IRQ
Suspend Mode
Soft-Off by PWR-BTTN
Wake-Up by PCI card
Wake up On LAN
Resume by Alarm
x Date (of Month) Alarm
x Time (hh:mm:ss) Alarm
[Enabled]
[User Define]
[3]
[Disabled]
[Instant-Off]
[Enabled]
[Enabled]
[Disabled]
[0]
[0 : 0 : 0]
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
Item Help
Menu Level
▶
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Power Management Setup Screen
The “Power Management Setup” allows the user to configure the system to
the most effectively save energy while operating in a manner consistent with
your own style of computer use.
ACPI FUNCTION:
Users are allowed to enable or disable the Advanced Configuration and
Power Management (ACPI).
Page: 4-18
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
POWER MANAGEMENT:
This item allows the user to select the type or degree of power saving and is
directly related to the following modes:
a. HDD Power Down
b. Suspend Mode
MODEM USE IRQ:
This item enable you to name the interrupt request (IRQ) line assigned to
the modem (if any) on your system. Activity of the selected IRQ always
awakens the system.
SUSPEND MODE:
When enabled and after the set time of system inactivity, all devices except
the CPU will be shut off.
SOFT-OFF BY PWR-BTTN:
Pressing the power button for more than 4 seconds forces the system to
enter the Soft-Off state when the system has “hung”. The choices are
Delay 4 Sec and Instant-Off.
WAKE-UP BY PCI CARD:
An input signal on the serial Ring Indicator (RI) line (in other words, an
incoming call on the modem) awakens the system from the soft-off state.
RESUME BY ALARM:
When enabled, you can set the date and time at which the RTC alarm
awakens the system from Suspend mode.
PM EVENTS:
PM Events are I/O events whose occurrence can prevent the system from
entering a power saving mode or can awaken the system from such a mode.
In effect, the system remains alert for anything, which occurs to a device,
which is configured as Enabled, even when the system is in a power down
mode.
nPrimary IDE 0
oPrimary IDE 1
pSecondary IDE 0
qSecondary IDE 1
rFDD, COM, LPT Port
sPCI PIRQ[A-D]#
Prox-1750G1/G2 USER′S MANUAL
Page: 4-19
Chapter
4
Award BIOS Setup
4-8. PNP/PCI CONFIGURATION
Choose 〝PNP/PCI CONFIGURATION〞 from the main menu, a display
will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
PNP OS Installed
Reset Configuration Data
Resources Controlled By
x IRQ Resources
x DMA Resources
PCI/VGA Palette Snoop
[Yes]
[Disabled]
Item Help
[Auto(ESCD)]
Press Enter
Press Enter
Menu Level
▶
Select Yes if you are
using a Plug and Play
capable operating
system Select No if you
need the BIOS to
configure non-boot
devices
[Disabled]
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
PNP/PCI CONFIGURATION
This section describes how to configure PCI bus system. PCI, also known as
Personal Computer Interconnect, is a system which allows I/O devices to
operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components. This section covers technical items,
which is strongly recommended for experienced users only.
PNP OS INSTALLED:
This item allows you to determine install PnP OS or not.
Page: 4-20
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
RESET CONFIGURATION DATA:
Normally, you leave this field Disabled. Select Enabled to reset Extended
System Configuration Data (ESCD) when you exit Setup if you have
installed a new add-on and the system configuration has caused such a
serious conflict that the operating system can not boot.
RESOURCE CONTROLLED BY:
The Award Plug and Play Bios can automatically configure all of the booth
and Plug and Play-compatible devices. However, this capability means
absolutely nothing unless you are using a Plug and Play operating system
such as Windows 95. By choosing “manual”, you are allowed to
configure the IRQ Resources, DMA Resources and Memory Resources.
The choices are Auto(ESCD) and Manual.
IRQ RESOURCES:
You may assign each system interrupt a type, depending on the type of
device using the interrupt.
IRQ3/4/5/7/9/10/11/12/14/15 ASSIGNED TO:
This item allows you to determine the IRQ assigned to ISA bus and is not
available to any PCI slot. Legacy ISA for devices compliant with the original PC AT bus specification, PCI/ISA PnP for devices compliant with the
Plug and Play standard whether designed for PCI or ISA bus architecture.
DMA RESOURCES:
When resources are controlled manually, assign each system DMA channel
a type, depending on the type of device using the DMA channel.
DMA 0/1/3/5/6/7 ASSIGNED TO:
Legacy ISA for devices compliant with the original PC AT bus specification, PCI/ISA PnP for devices compliant with the Plug and Play standard
whether designed for PCI or ISA bus architecture.
PCI/VGA PALETTE SNOOP:
Leave this field at disabled.
Prox-1750G1/G2 USER′S MANUAL
Page: 4-21
Chapter
4
Award BIOS Setup
4-9. PC HEALTH STATUS
Choose 〝PC HEALTH STATUS〞 from the main menu, a display will
be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
CPU Warning Temperature
[50½C/122½F]
Current CPU Temperature
[49½C/120½F]
Current SYSTEM Fan Speed
Current CPU Fan Speed
Vcore
3.3 V
+5 V
+12 V
-12 V
-5 V
VBAT (V)
5VSB (V)
Shutdown Temperature
Item Help
0 RPM
2481 RPM
1.42V
3.34V
5.05V
11.79V
(-) 12.52V
(-) 4.99V
3.18V
4.96V
[60½C/140½F]
Menu Level
▶
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
PC Health Status Setup Screen
CPU WARMING TEMPERATURE:
Select the combination of lower and upper limits for the CPU temperature.
If the CPU temperature extends beyond either limit, any warning
mechanism programmed into your system will be activated.
CURRENT CPU TEMPERATURE:
This field displays the current CPU temperature, if your computer contains
a monitoring system.
Page: 4-22
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
SHUTDOWN TEMPERATURE:
User is allowed to set the temperature on which the system automatically
shutdown when reaches or exceeds the temperature set.
4-10. FREQUENCY/VOLTAGE CONTROL
Choose 〝FREQUENCY/VOLTAGE CONTROL〞 from the main menu,
a display will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
Spread Spectrum
[Disabled]
Item Help
Menu Level
▶
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Frequency / Voltage Control Setup Screen
This setup menu allows you to specify your settings for frequency/voltage
control.
SPREAD SPECTRUM:
This item allows you to enable or disable the spread spectrum modulate.
Prox-1750G1/G2 USER′S MANUAL
Page: 4-23
Chapter
4
Award BIOS Setup
4-11. LOAD FAIL-SAFE DEFAULTS
By pressing the <ENTER> key on this item, you get a confirmation dialog
box with a message similar to the following:
Load Fail-Safe Defaults ( Y/N ) ? N
To use the BIOS default values, change the prompt to "Y" and press the
<Enter > key. CMOS is loaded automatically when you power up the
system.
4-12. LOAD OPTIMIZED DEFAULTS
When you press <Enter> on this category, you get a confirmation dialog
box with a message similar to the following:
Load Optimized Defaults ( Y/N ) ? N
Pressing "Y" loads the default values that are factory setting for optimal
performance system operations.
Page: 4-24
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
4-13. PASSWORD SETTING
User is allowed to set either supervisor or user password, or both of them.
The difference is that the supervisor password can enter and change the
options of the setup menus while the user password can enter only but do not
have the authority to change the options of the setup menus.
TO SET A PASSWORD
When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.
Enter Password:
Type the password up to eight characters in length, and press < Enter >.
The password typed now will clear any previously entered password from
CMOS memory. You will be asked to confirm the password. Type the
password again and press the < Enter > key. You may also press < Esc >
to abort the selection and not enter a password.
User should bear in mind that when a password is set, you will be
asked to enter the password everything you enter CMOS setup Menu.
TO DISABLE THE PASSWORD
To disable the password, select this function (do not enter any key when
you are prompt to enter a password), and press the <Enter> key and a
message will appear at the center of the screen:
PASSWORD DISABLED!!!
Press any key to continue...
Press the < Enter > key again and the password will be disabled. Once the
password is disabled, you can enter Setup freely.
Prox-1750G1/G2 USER′S MANUAL
Page: 4-25
Chapter
4
Award BIOS Setup
4-14. SAVE & EXIT SETUP
After you have completed adjusting all the settings as required, you must
remember to save these setting into the CMOS RAM. To save the settings,
select “SAVE & EXIT SETUP” and press <Enter>, a display will be shown
as follows:
Phoenix - AwardBIOS CMOS Setup Utility
▶Standard CMOS Features
▶Frequency/Voltage Control
▶Advanced BIOS Features
Load Fail-Safe Defaults
▶Advanced Chipset Features
Load Optimized Defaults
▶Integrated Peripherals
Set Supervisor Password
▶Power Management
▶PnP/PCI Configura
word
Save to CMOS and EXIT Y/N)? Y
etup
▶PC Health Status
Saving
Esc : Quit
F9 : Menu in BIOS
F10 : Save & Exit Setup
↑↓→← : Select Item
Save Data to CMOS
When you confirm that you wish to save the settings, your system will be
automatically restarted and the changes you have made will be implemented.
You may always call up the setup program at any time to adjust any of the
individual items by pressing the <Del> key during boot up.
Page: 4-26
Prox-1750G1/G2 USER′S MANUAL
Chapter
4
Award BIOS Setup
4-15. EXIT WITHOUT SAVING
If you wish to cancel any changes you have made, you may select the
“EXIT WITHOUT SAVING” and the original setting stored in the CMOS
will be retained. The screen will be shown as below:
Phoenix - AwardBIOS CMOS Setup Utility
▶Standard CMOS Features
▶Frequency/Voltage Control
▶Advanced BIOS Features
Load Fail-Safe Defaults
▶Advanced Chipset Features
Load Optimized Defaults
▶Integrated Peripherals
Set Supervisor Password
▶Power Management
▶PnP/PCI Configura
word
Quit Without Saving (Y/N)? N
etup
▶PC Health Status
Saving
Esc : Quit
F9 : Menu in BIOS
F10 : Save & Exit Setup
↑↓→← : Select Item
Abandon all Datas
Prox-1750G1/G2 USER′S MANUAL
Page: 4-27
APPENDIX
EXPANSION
BUS
A
This appendix indicates the pin assignments.
Section includes:
z ISA BUS Pin Assignment
z PCI BUS Pin Assignment
Page: A-1
Appendix
A
Expansion Bus
ISA BUS PIN ASSIGNMENT
The ISA-bus connector is divided into two sets : one consists of 62 pins; the other
consists of 36 pins.
A1
A31 C1
C18
B1
B31 D1
D18
The pin assignments
as follows :
B
A
D
C
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
GND
RESET
+5V
IRQ9
-5V
DRQ2
-12V
OWS
+12V
GND
-SMEMW
-SMEMR
-IOW
-IOR
-DACK3
-DRQ3
-DACK1
-DRQ1
-REFRESH
BCLK
IRQ7
IRQ6
IRQ5
IRQ4
IRQ3
-DACK2
T/C
BALE
+5V
OSC
GND
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
-I/O CH CHK
SD07
SD06
SD05
SD04
SD03
SD02
SD01
SD00
-I/O CH RDY
AEN
SA19
SA18
SA17
SA16
SA15
SA14
SA13
SA12
SA11
SA10
SA09
SA08
SA07
SA06
SA05
SA04
SA03
SA02
SA01
SA00
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
-MEMCS16
-I/OCS16
IRQ10
IRQ11
IRQ12
IRQ15
IRQ14
-DACK0
DRQ0
-DACK5
DRQ5
-DACK6
DRQ6
-DACK7
DRQ7
+5V
-MASTER
GND
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
SBHE
LA23
LA22
LA21
LA20
LA19
LA18
LA17
-MEMR
-MEMW
SD08
SD09
SD10
SD11
SD12
SD13
SD14
SD15
Page: A-2
Prox-1750G1/G2 USER′S MANUAL
Appendix
A
Expansion Bus
PCI BUS PIN ASSIGNMENT
Like ISA-BUS connector, the PCI-BUS edge connector is also divided into two
sets: one consists of 98-pin; the other consists of 22-pin.
The pin assignments are as follows :
B1
B49 B52
B62
A1
A49 A52
A62
B
A
B
A
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
-12V
TCK
GND
TDO
+5V
+5V
INTB#
INTD#
REQ3#
REQ1#
GNT3#
GND
GND
CLKA
GND
CLKB
GND
REQ0#
+5V(I/O)
AD31
AD29
GND
AD27
AD25
+3.3V
C/BE3#
AD23
GND
AD21
AD19
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
TRST#
+12V
TMS
TDI
+5V
INTA#
INTC#
+5V
CLKC
+5V(I/O)
CLKD
GND
GND
GNT1#
RST#
+5V(I/O)
GNT0#
GND
REQ2#
AD30
+3.3V
AD28
AD26
GND
AD24
GNT2#
+3.3V
AD22
AD20
GND
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
+3.3V
AD17
C/BE2#
GND
IRDY#
+3.3V
DEVSEL#
GND
LOCK#
PERR#
+3.3V
SERR#
+3.3V
C/BE1#
AD14
GND
AD12
AD10
GND
AD08
AD07
+3.3V
AD05
AD03
GND
AD01
+5V(I/O)
ACK64#
+5V
+5V
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
AD18
AD16
+3.3V
FRAME#
GND
TRDY#
GND
STOP#
+3.3V
SDONE
SB0#
GND
PAR
AD15
+3.3V
AD13
AD11
GND
AD09
C/BE0#
+3.3V
AD06
AD04
GND
AD02
AD00
+5V(I/O)
REQ64#
+5V
+5V
Prox-1750G1/G2 USER′S MANUAL
Page: A-3
APPENDIX
TECHNICAL
SUMMARY
B
This section introduce you the maps concisely.
Sections include:
z Block Diagram
z Interrupt Map
z RTC (Standard) RAM Bank
z Timer & DMA Channels Map
z I / O & Memory Map
Page: B-1
Page: B-2
Pa ra llel
LPC SIO
Keyb oa rd
Mouse
W83627HF
Aud io Cod ec
ALC201A
LAN 1
Seria l 2
DDRAM
Mo dules
PC200/266
Cloc k
Synthesizer
Cy82323
PCI CONN2
82562EM
PCI CONN1
4MB Fla sh BIOS
Seria l 1
100MH z/ 133MH z
PCI CONN3
Firm Wa re Hub
ICH 4
82801DB
845G/GE
Bro o kDALE-G
IDE Prim a ry
Floop y
350 Mpixels/s
USB 1.1/2.0
Six Po rt
IDE Se c o nd a ry
VGA DSUB
2 Mused Intel DVO p orts
GMCH
Soc ke t 478
Proc essor P4_CPU
PCI/ISA
Seria l 3
Seria l 4
W83877TF
ISA
SUPER IO
IT8888F/BF
B
AGP 4X
OR
VRM 9.0
HIP 6302
Appendix
Technical Summary
BLOCK DIAGRAM
ISA CONN1
82551QM/82540EM
LAN 2
PPCI CONN
PCI CONN6
PCI CONN4
PCI CONN5
Prox-1750G1/G2 USER′S MANUAL
Appendix
B
Technical Summary
INTERRUPT MAP
IRQ
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ASSIGNMENT
System TIMER interrupt from TIMER-0
Keyboard output buffer full
Cascade for IRQ 8-15
Serial port 2
Serial port 1
Parallel Port 2
Floppy Disk adapter
Parallel port 1
RTC clock
Available
Serial port 3
Serial port 4
Available
Math coprocessor
Hard Disk adapter
Available
Prox-1750G1/G2 USER′S MANUAL
Page: B-3
Appendix
B
Technical Summary
RTC (STANDARD) RAM BANK
CODE
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh-7Fh
Page: B-4
ASSIGNMENT
Seconds
Second alarm
Minutes
Minutes alarm
Hours
Hours alarm
Day of week
Day of month
Month
Year
Status register A
Status register B
Status register C
Status register D
114 Bytes of User RAM
Prox-1750G1/G2 USER′S MANUAL
Appendix
B
Technical Summary
TIMER & DMA CHANNELS MAP
Timer Channel Map :
Timer Channel
0
1
2
Assignment
System timer interrupt
DRAM Refresh request
Speaker tone generator
DMA Channel Map :
DMA Channel
0
1
2
3
4
5
6
7
Assignment
Available
Available
Floppy Disk adapter
Available
Cascade
Available
Available
Available
Prox-1750G1/G2 USER′S MANUAL
Page: B-5
Appendix
B
Technical Summary
I/O & MEMORY MAP
Fixed I/O Ranges Decoded by ICH2 :
I/O Address
00h-08h
09h-0Eh
0Fh
10h-18h
19h-1Eh
1Fh
20h-21h
24h-25h
28h-29h
2Ch-2Dh
2Eh-2Fh
30h-31h
34h-35h
38h-39h
3Ch-3Dh
40h-42h
43h
4E-4F
50h-52h
53h
60h
61h
62h
63h
64h
65h
66h
67h
70h
71h
72h
73h
74h
75h
76h
77h
Page: B-6
Read Target
DMA Controller
Reserved
DMA Controller
DMA Controller
Reserved
DMA Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
LPC SIO
Interrupt Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
Timer/Counter
Reserved
LPC SIO
Timer/Counter
Reserved
Microcontroller
NMI Controller
Microcontroller
NMI Controller
Microcontroller
NMI Controller
Microcontroller
NMI Controller
Reserved5
RTC Controller
RTC Controller
RTC Controller
RTC Controller
RTC Controller
RTC Controller
RTC Controller
Write Target
DMA Controller
DMA Controller
DMA Controller
DMA Controller
DMA Controller
DMA Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
LPC SIO
Interrupt Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
Timer/Counter
Timer/Counter
LPC SIO
Timer/Counter
Timer/Counter
Microcontroller
NMI Controller
Microcontroller
NMI Controller
Microcontroller
NMI Controller
Microcontroller
NMI Controller
NMI & RTC controller
RTC Controller
NMI & RTC controller
RTC Controller
NMI & RTC controller
RTC Controller
NMI & RTC controller
RTC Controller
Internal Unit
DMA
DMA
DMA
DMA
DMA
DMA
Interrupt
Interrupt
Interrupt
Interrupt
Forwarder to LPC
Interrupt
Interrupt
Interrupt
Interrupt
PIT (8254)
PIT
Forwarder to LPC
PIT
PIT
Forwarder to LPC
Processor I/F
Forwarder to LPC
Processor I/F
Forwarder to LPC
Processor I/F
Forwarder to LPC
Processor I/F
RTC
RTC
RTC
RTC
RTC
RTC
RTC
RTC
Prox-1750G1/G2 USER′S MANUAL
Appendix
I/O Address
Read Target
80h
DMA Controller
81h-83h
84h-86h
DMA Controller
DMA Controller
87h
88h
DMA Controller
DMA Controller
89h-8Bh
8Ch-8Eh
DMA Controller
DMA Controller
08Fh
90h-91h
92h
93h-9Fh
A0h-A1h
A4h-A5h
A8h-A9h
ACh-ADh
B0h-B1h
B2h-B3h
B4h-B5h
B8h-B9h
BCh-BDh
C0h-D1h
D2h-DDh
DEh-DFh
F0h
DMA Controller
DMA Controller
Reset Generator
DMA Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
Power Management
Interrupt Controller
Interrupt Controller
Interrupt Controller
DMA Controller
Reserved
DMA Controller
See Note 3
170h-177h
1F0h-1F7h
376h
3F6h
4D0h-4D1h
CF9h
IDE Controller1
IDE Controller2
IDE Controller1
IDE Controller2
Interrupt Controller
Reset Generator
Write Target
DMA controller &
LPC/PCI
DMA Controller
DMA Controller &
LPC or PCI
DMA Controller
DMA Controller &
LPC or PCI
DMA Controller
DMA Controller &
LPC or PCI
DMA Controller
DMA Controller
Reset Generator
DMA Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
Interrupt Controller
Power Management
Interrupt Controller
Interrupt Controller
Interrupt Controller
DMA Controller
DMA Controller
DMA Controller
FERR# /IGNNE#/
Interrupt Controller
IDE Controller1
IDE Controller2
IDE Controller1
IDE Controller2
Interrupt Controller
Reset Generator
B
Technical Summary
Internal Unit
DMA
DMA
DMA
DMA
DMA
DMA
DMA
DMA
DMA
Processor I/F
DMA
Interrupt
Interrupt
Interrupt
Interrupt
Interrupt
Power Management
Interrupt
Interrupt
Interrupt
DMA
DMA
DMA
Processor interface
Forwarded to IDE
Forwarded to IDE
Forwarded to IDE
Forwarded to IDE
Interrupt
Processor interface
Notes:
1. Only if IDE Standard I/O space is enabled for Primary Drive. Otherwise, the target is PCI.
2. Only if IDE Standard I/O space is enabled for Secondary Drive. Otherwise, the target is PCI.
3. If POS_DEC_EN bit is enabled, reads from F0h will not be decoded by the ICH2. If
POS_DEC_EN is not enabled, reads from F0h will forward to LPC.
Prox-1750G1/G2 USER′S MANUAL
Page: B-7
Appendix
B
Technical Summary
Memory Decode Ranges From Processor Perspective :
Memory Range
0000 0000h-000D FFFFh
0010 0000-TOM (Top of
Memory)
000E 0000h-000F FFFFh
FEC0 0000h-FEC0 0100h
FFC0 0000h-FFC7 FFFFh
FF80 0000h-FF87 FFFFh
FFC8 0000h-FFCF FFFFh
FF88 0000h-FF8F FFFFh
FFD0 0000h-FFD7 FFFFh
FF90 0000h-FF97 FFFFh
FFD8 0000h-FFDF FFFFh
FF98 0000h-FF9F FFFFh
FFE0 0000h-FFE7 FFFFh
FFA0 0000h-FFA7 FFFFh
FFE8 0000h-FFEF FFFFh
FFA8 0000h-FFAF FFFFh
FFF0 0000h-FFF7 FFFFh
FFB0 0000h-FFB7 FFFFh
FFF8 0000h-FFFF FFFFh
FFB8 0000h-FFBF FFFFh
FF70 0000h-FF7F FFFFh
FF30 0000h-FF3F FFFFh
FF60 0000h-FF6F FFFFh
FF20 0000h-FF2F FFFFh
FF50 0000h-FF5F FFFFh
FF10 0000h-FF1F FFFFh
FF40 0000h-FF4F FFFFh
FF00 0000h-FF0F FFFFh
Anywhere in 4GB range
All Other
Page: B-8
Target
Dependency/Comments
Main Memory
TOM registers in Host Controller
FWH
Bit 7 in FWH Decode Enable
Register is set
I/O APIC inside ICH2
FWH
Bit 0 in FWH Decode Enable
Register
FWH
Bit 1 in FWH Decode Enable
Register
FWH
Bit 2 in FWH Decode Enable
Register is set
FWH
Bit 3 in FWH Decode Enable
Register is set
FWH
Bit 4 in FWH Decode Enable
Register is set
FWH
Bit 5 in FWH Decode Enable
Register is set
FWH
Bit 6 in FWH Decode Enable
Register is set
FWH
Always Enabled.
The top two 64K blocks of this
range can be swapped as
described in Section 6.4.1.
FWH
Bit 3 in FWH Decode Enable 2
Register is set
FWH
Bit 2 in FWH Decode Enable 2
Register is set
FWH
Bit 1 in FWH Decode Enable 2
Register is set
FWH
Bit 0 in FWH Decode Enable 2
Register is set
D110 LAN Controller Enable via BAR in Device
29:Function 0 (D110 LAN
Controller)
PCI
None
Prox-1750G1/G2 USER′S MANUAL
APPENDIX
TROUBLE
SHOOTING
C
This section outlines the error messages that may occur when you
operate the system. It also gives you the suggestions on solving the
problems.
Section includes:
z Trouble Shooting for Error Messages
z Trouble Shooting for POST Code
Page: C-1
Appendix
C
Trouble Shooting
TROUBLE SHOOTING FOR ERROR MESSAGES
The following information gives you the error messages and the troubleshooting. Please adjust your systems according to the messages below. And
make sure all the components and connectors are in proper position and
firmly attached. If the errors still encountered, please contact with your
distributor for maintenance.
POST BEEP :
Currently there are two kinds of beep codes in BIOS. One code indicates
that a video error has occurred and the BIOS cannot initialize the video
screen to display any additional information. This beep code consists of a
single long beep followed by two short beeps. The other code indicates that
your DRAM error has occurred. This beep code consists of a single long
beep repeatedly.
CMOS BATTERY HAS FAILED :
This message informs you that the CMOS battery is no longer functional.
The user should replace it.
CMOS CHECKSUM ERROR :
This message informs you that the CMOS is incorrect. This error may
have caused by a weak battery. Check the battery and replace if necessary.
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER :
No boot device was found. This could mean that either a boot drive was
not detected or the drive does not contain proper system boot files. Insert a
system disk into Drive A: and press < Enter >. If you assumed the system
would boot from the hard drive, make sure the controller is inserted
correctly and all cables are properly attached. Also make sure the disk is
formatted as a boot device. Then reboot the system.
DISKETTE DRIVES OR TYPES MISMATCH ERROR - RUN SETUP :
Type of diskette drive installed in the system is different from the CMOS
definition. Run Setup to reconfigure the drive type correctly.
Page: C-2
Prox-1750G1/G2 USER′S MANUAL
Appendix
C
Trouble Shooting
DISPLAY SWITCH IS SET INCORRECTLY :
Display switch on the motherboard can be set to either monochrome or
color. This indicates the switch is set to a different setting than indicated in
Setup. Determine which setting is correct, and then either turn off the
system and change the jumper, or enter Setup and change the VIDEO
selection.
DISPLAY TYPE HAS CHANGED SINCE LAST BOOT :
Since last powering off the system, the display adapter has been changed.
You must configure the system for the new display type.
EISA CONFIGURATION CHECKSUM ERROR
PLEASE RUN EISA CONFIGURATION UTILITY :
The EISA non-violatile RAM checksum is incorrect or cannot correctly
read the EISA slot. This can indicate either the EISA non-volatile
memory has become corrupt or the slot has been configured incorrectly.
Also be sure the card is installed firmly in the slot.
EISA CONFIGURATION IS NOT COMPLETE
PLEASE RUN EISA CONFIGURATION UTILITY :
The slot configure information stored in the EISA non-volatile memory is
incomplete.
Note: When either of these errors appear, the system will boot in ISA mode,
which allows you to run the EISA Configuration Utility.
ERROR ENCOUNTERED INITIALIZING HARD DRIVE :
Hard drive cannot be initialized. Be sure the adapter is installed correctly
and all cables are correctly and firmly attached. Also be sure the correct
hard drive type is selected in Setup.
ERROR INITIALIZING HARD DISK CONTROLLER :
Cannot initialize controller. Make sure the cord is correctly and firmly
installed in the bus. Be sure the correct hard drive is selected in Setup. Also
check to see if any jumper needs to be set correctly on the hard drive.
Prox-1750G1/G2 USER′S MANUAL
Page: C-3
Appendix
C
Trouble Shooting
FLOPPY DISK CNTRLR ERROR OR NO CNTRLR PRESENT :
Cannot find or initialize the floppy drive controller. Make sure the
controller is installed correctly and firmly. If there are no floppy drives
installed, be sure the Diskette Drive selection in Setup is set to NONE.
INVALID EISA CONFIGURATION
PLEASE RUN EISA CONFIGURATION UTILITY :
The non-volatile memory containing EISA configuration information was
programmed incorrectly or has become corrupt. Re-run EISA configuration
utility to correctly program the memory.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.
KEYBOARD ERROR OR NO KEYBOARD PRESENT :
Cannot initialize the keyboard. Make sure that the keyboard is properly
attached and no keys being pressed during the boot.
If you are purposely configuring the system without a keyboard, set the
error halt condition in Setup to HALT ON ALL, BUT KEYBOARD. This
will cause the BIOS to ignore the missing keyboard and continue the boot.
MEMORY ADDRESS ERROR AT ... :
Indicates a memory address error at a specific location. You can use this
location along with the memory map for your system to find and replace the
bad memory chips.
MEMORY PARITY ERROR AT ... :
Indicates a memory parity error at a specific location. You can use this
location along with the memory map for your system to find and replace the
bad memory chips.
MEMORY SIZE HAS CHANGED SINCE LAST BOOT :
Memory has been added or removed since the last boot. In EISA mode use
Configuration Utility to reconfigure the memory configuration. In ISA
mode enter Setup and enter the new memory size in the memory fields.
Page: C-4
Prox-1750G1/G2 USER′S MANUAL
Appendix
C
Trouble Shooting
MEMORY VERIFY ERROR AT ... :
Indicates an error verifying a value already written to memory. Use the
location along with your system's memory map to locate the bad chip.
OFFENDING ADDRESS NOT FOUND :
This message is used in conjunction with the I/O CHANNEL CHECK and
RAM PARITY ERROR messages when the segment that has caused the
problem cannot be isolated.
OFFENDING SEGMENT :
This message is used in conjunction with the I/O CHANNEL CHECK and
RAM PARITY ERROR messages when the segment that has caused the
problem has been isolated.
PRESS A KEY TO REBOOT :
This will be displayed at the bottom screen when an error occurs that
requires you to reboot. Press any key and the system will reboot.
PRESS F1 TO DISABLE NMI, F2 TO REBOOT :
When BIOS detects a Non-maskable Interrupt condition during boot, this
will allow you to disable the NMI and continue to boot, or you can reboot
the system with the NMI enabled.
RAM PARITY ERROR – CHECKING FOR SEGMENT :
Indicates a parity error in Random Access Memory.
Should be Empty But EISA Board Found
PLEASE RUN EISA CONFIGURATION UTILITY :
A valid board ID was found in a slot that was configured as having no
board ID.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.
Should Have EISA Board But Not Found
PLEASE RUN EISA CONFIGURATION UTILITY :
The board installed is not responding to the ID request, or no board ID has
been found in the indicated slot.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.
Prox-1750G1/G2 USER′S MANUAL
Page: C-5
Appendix
C
Trouble Shooting
Slot Not Empty :
Indicates that a slot designated as empty by the EISA Configuration Utility
actually contains a board.
SYSTEM HALTED, (CTRL-ALT-DEL) TO REBOOT :
Indicates the present boot attempt has been aborted and the system must be
rebooted. Press and hold down the CTRL and ALT keys and press DEL.
Wrong Board in Slot
PLEASE RUN EISA CONFIGURATION UTILITY :
The board ID does not match the ID stored in the EISA non-volatile
memory.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.
FLOPPY DISK(S) FAIL (80) :
Unable to reset floppy subsystem.
FLOPPY DISK(S) FAIL (40) :
Floppy type dismatch.
Hard Disk(S) Fail (80) :
Hard Disk Drive reset failed.
Hard Disk(S) Fail (40) :
Hard Disk Drive controller diagnostics failed.
Hard Disk(S) Fail (20) :
Hard Disk Drive initialization error.
Hard Disk(S) Fail (10) :
Unable to recalibrate fixed disk.
Hard Disk(S) Fail (08) :
Sector Verify failed.
Keyboard is locked out – Unlock the key :
BIOS detect the keyboard is locked. P17 of keyboard controller is pulled
low.
Page: C-6
Prox-1750G1/G2 USER′S MANUAL
Appendix
C
Trouble Shooting
Keyboard error or no keyboard present :
Cannot initialize the keyboard. Make sure the keyboard is attached
correctly and no keys are being pressed during the boot.
Manufacturing POST loop :
System will repeat POST procedure infinitely while the P15 of keyboard
controller is pull low. This is also used for M/B burn in test.
BIOS ROM checksum error – System halted :
The checksum of ROM address F0000H-FFFFFH is bad.
Memory test fail :
BIOS reports the memory test fail if the onboard memory is tested error.
Prox-1750G1/G2 USER′S MANUAL
Page: C-7
Appendix
C
Trouble Shooting
TROUBLE SHOOTING FOR POST CODES
The lists below indicate you the post codes. Please follow the instruction to
adjust your system. If the error still occurred, please contact with your
distributor for maintenance.
CFh
:
Test CMOS R/W functionality.
C0h
:
Early chipset initialization
- Disable shadow RAM
- Disable L2 cache (socket 7 or below)
- Program basic chipset registers
C1h
:
Detect memory
- Auto-detection of DRAM size, type and ECC
- Auto-detection of L2 cache (socket 7 or below)
C3h
:
Expand compressed BIOS code to DRAM.
C5h
:
Call chipset hook to copy BIOS black to E000 & F000 shadow
RAM.
0h1
:
Expand the Xgroup codes locating in physical address 1000:0
02h
:
Reserved.
03h
:
Initial Superio_Early_Init switch.
04h
:
Reserved.
05h
:
1. Blank out screen
2. Clear CMOS error flag
06h
:
Reserved
07h
:
1. Clear 8042 interface
2. Initialize 8042 self-test
Page: C-8
Prox-1750G1/G2 USER′S MANUAL
Appendix
C
Trouble Shooting
08h
:
1. Test special keyboard controller for Winbond 977 series Super
I/O Chips.
2. Enable keyboard interface.
09h
:
Reserved
0Ah :
1. Disable PS/2 mouse interface (optional)
2. Auto detect ports for keyboard & mouse followed by a port &
interface swap (optional).
3. Reset keyboard for Winbond 977 series Super I/O chips.
0Bh :
Reserved
0Ch :
Reserved
0Dh :
Reserved
0Eh :
Test F000h segment shadow to see whether it is R/W-able or not.
If test fails, keep beeping the speaker.
0Fh :
Reserved
10h :
Auto detect flash type to load appropriate flash R/W codes into the
run time area in F000 for ESCD and DMI support.
11h :
Reserved
12h :
Use walking 1’s algorithm to check out interface in CMOS
circuitry. Also set real-time clock power status, and then check
for override.
13h :
Reserved
14h :
Program chipset default values into chipset. Chipset default
values are MODBINable by OEM customers.
15h :
Reserved
16h :
Initial Early_Init_Onboard_Generator switch.
Prox-1750G1/G2 USER′S MANUAL
Page: C-9
Appendix
C
Trouble Shooting
17h
:
Reserved
18h
:
Detect CPU information including brand, SMI type (Cyrix or Intel)
and CPU level (586 or 686).
19h
:
Reserved
1Ah :
Reserved
1Bh :
Initial interrupts vector table. If no special specified, all H/W
interrupts are directed to SPURIOUS_INIT_HDLR & S/W
interrupts to SPURIOUS_soft_HDLR.
1Ch :
Reserved
1Dh :
Initial EARLY_PM_INIT switch
1Eh :
Reserved
1Fh :
Load keyboard matrix (notebook platform)
20h :
Reserved
21h :
HPM initialization (notebook platform)
22h :
Reserved
23h :
1. Check validity of RTC value:
e.g. a value of 5Ah is an invalid value for RTC minute.
2. Load CMOS settings into BIOS stack. If CMOS checksum
fails, use default value instead.
3. Prepare BIOS resource map for PCI & PnP use. If ESCD is
valid, take into consideration of the ESCD’s legacy information.
4. Onboard clock generator initialization. Disable respective
clock resource to empty PCI & DIMM slots.
5. Early PCI initialization:
-Enumerate PCI bus number
-Assign memory & I/O resource
-Search for a valid VGA device & VGA BIOS, and put it into
C000:0.
Page: C-10
Prox-1750G1/G2 USER′S MANUAL
Appendix
C
Trouble Shooting
24h
:
Reserved
25h
:
Reserved
26h
:
Reserved
27h
:
Initialize INT 09 buffer
28h
:
Reserved
29h
:
1. Program CPU internal mtrr (P6 & PII) for 0-640K memory
address.
2. Initialize the APIC for Pentium class CPU.
3. Program early chipset according to CMOS setup.
Example: onboard IDE controller.
4. Measure CPU speed.
5. Invoke video BIOS.
2Ah
:
Reserved
2Bh
:
Reserved
2Ch
:
Reserved
2Dh
:
1. Initialize multi-language
2. Put information on screen display, including Award title, CPU
type, CPU speed …
2Eh
:
Reserved
2Fh
:
Reserved
30h
:
Reserved
31h
:
Reserved
32h
:
Reserved
33h
:
Reset keyboard except Winbond 977 series Super I/O chips.
Prox-1750G1/G2 USER′S MANUAL
Page: C-11
Appendix
C
Trouble Shooting
34h
:
Reserved
35h
:
Reserved
36h
:
Reserved
37h
:
Reserved
38h
:
Reserved
39h
:
Reserved
3Ah :
Reserved
3Bh
:
Reserved
3Ch
:
Test 8254
3Dh
:
Reserved
3Eh
:
Test 8259 interrupt mask bits for channel 1.
3Fh
:
Reserved
40h
:
Test 8259 interrupt mask bits for channel 2.
41h
:
Reserved
42h
:
Reserved
43h
:
Test 8259 functionality.
44h
:
Reserved
45h
:
Reserved
46h
:
Reserved
47h
:
Initialize EISA slot
Page: C-12
Prox-1750G1/G2 USER′S MANUAL
Appendix
C
Trouble Shooting
48h
:
Reserved
49h
:
1. Calculate total memory by testing the last double word of each
64K page.
2. Program writes allocation for AMD K5 CPU.
4Ah :
Reserved
4Bh :
Reserved
4Ch :
Reserved
4Dh :
Reserved
4Eh :
1. Program MTRR of M1 CPU
2. Initialize L2 cache for P6 class CPU & program CPU with
proper cacheable range.
3. Initialize the APIC for P6 class CPU.
4. On MP platform, adjust the cacheable range to smaller one in
case the cacheable ranges between each CPU are not identical.
4Fh :
Reserved
50h
:
Initialize USB
51h
:
Reserved
52h
:
Test all memory (clear all extended memory to 0)
53h
:
Reserved
54h
:
Reserved
55h
:
Display number of processors (multi-processor platform)
56h
:
Reserved
57h
:
1. Display PnP logo
2. Early ISA PnP initialization
-Assign CSN to every PnP device.
Prox-1750G1/G2 USER′S MANUAL
Page: C-13
Appendix
C
Trouble Shooting
58h
:
Reserved
59h
:
Initialize the combined Trend Anti-Virus code.
5Ah :
Reserved
5Bh :
(Optional Feature)
Show message for entering AWDFLASH.EXE from FDD
(optional)
5Ch :
Reserved
5Dh :
1. Initialize Init_Onboard_Super_IO switch.
2. Initialize Init_Onboard_AUDIO switch.
5Eh :
Reserved
5Fh :
Reserved
60h
:
Okay to enter Setup utility; i.e. not until this POST stage can users
enter the CMOS setup utility
61h
:
Reserved
62h
:
Reserved
63h
:
Reserved
64h
:
Reserved
65h
:
Initialize PS/2 Mouse
66h
:
Reserved
67h
:
Prepare memory size information for function call:
INT 15h ax=E820h
68h
:
Reserved
69h
:
Turn on L2 cache.
Page: C-14
Prox-1750G1/G2 USER′S MANUAL
Appendix
C
Trouble Shooting
6Ah
:
Reserved
6Bh
:
Program chipset registers according to items described in Setup
and Auto-configuration table.
6Ch
:
Reserved
6Dh
:
1. Assign resources to all ISA PnP devices.
2. Auto assign ports to onboard COM ports if the corresponding
item in Setup is set to “AUTO”.
6Eh
:
Reserved
6Fh
:
1. Initialize floppy controller.
2. Set up floppy related fields in 40:hardware.
70h
:
Reserved
71h
:
Reserved
72h
:
Reserved
73h
:
(Optional Feature)
Enter AWDFLASH.EXE if:
- AWDFLASH is found in floppy drive.
- ALT+F2 is pressed
74h
:
Reserved
75h
:
Detect & install all IDE devices: HDD, LS120, ZIP, CDROM…..
76h
:
Reserved
77h
:
Detect serial ports and parallel ports
78h
:
Reserved
79h
:
Reserved
7Ah :
Detect and install co-processor
Prox-1750G1/G2 USER′S MANUAL
Page: C-15
Appendix
C
Trouble Shooting
7Bh
:
Reserved
7Ch
:
Reserved
7Dh
:
Reserved
7Eh
:
Reserved
7Fh
:
1. Switch back to text mode if full screen logo is supported.
-If errors occur, report errors and wait for keys
-If no errors occur or F1 key is pressed to continue:
*Clear EPA or customization logo.
80h
:
Reserved
81h
:
Reserved
82h
:
1. Call chipset power management hook.
2. Recover the text fond used by EPA logo (not for full screen
logo).
3. If password is set, ask for password.
83h
:
Save all data in stack back to CMOS.
84h
:
Initialize ISA PnP boot devices.
85h
:
1. USB final initialization.
2. NET PC: Build SYSID structure.
3. Switch screen back to text mode.
4. Setup ACPI table at top of memory.
5. Invoke ISA adapter ROMs.
6. Assign IRQs to PCI devices.
7. Initialize APM.
8. Clear noise of IRQs.
86h
:
Reserved
87h
:
Reserved
Page: C-16
Prox-1750G1/G2 USER′S MANUAL
Appendix
C
Trouble Shooting
88h
:
Reserved
89h
:
Reserved
90h
:
Reserved
91h
:
Reserved
92h
:
Reserved
93h
:
Read HDD boot sector information for Trend Anti-Virus code.
94h
:
1. Enable l2 cache.
2. Program boot up speed.
3. Chipset final initialization.
4. Power management final initialization.
5. Clear screen and display summary table
6. Program K6 write allocation.
7. Program P6 class write combining.
95h
:
1. Program daylight saving.
2. Update keyboard LED and typematic rate.
96h
:
1. Build MP table.
2. Build and update ESCD.
3. Set CMOS century to 20h or 19h.
4. Load CMOS time into DOS timer tick.
5. Build MSIRQ routing table.
FFh :
Boot attempt (INT 19h)
/
Prox-1750G1/G2 USER′S MANUAL
Page: C-17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement