Bosch | AHS 52 LI | Instruction manual | Bosch AHS 52 LI Instruction manual Page 1 Monday, December 13, 2010 12:52 PM
Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
F 016 L70 729 (2010.12) O / 298 UNI
48 LI | 52 LI
Original instructions
Notice originale
Manual original
Manual original
Istruzioni originali
da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet
Πρωτότυπο οδηγιών χρήσης
Orijinal işletme talimat
Instrukcja oryginalna
Původní návod k používání
Pôvodný návod na použitie
Eredeti használati utasítás
Оригинальное руководство по эксплуатации
uk Оригінальна інструкція з
ro Instrucţiuni originale
bg Оригинална инструкция
Originalno uputstvo za rad
Izvirna navodila
Originalne upute za rad
Algupärane kasutusjuhend
Instrukcijas oriģinālvalodā
Originali instrukcija Page 4 Thursday, December 16, 2010 1:14 PM
F 016 L70 729 | (16.12.10)
Bosch Power Tools Page 5 Monday, December 13, 2010 12:55 PM
F 016 L70 729 | (13.12.10)
Bosch Power Tools Page 17 Monday, December 13, 2010 12:55 PM
English | 17
Safety Notes
Explanation of symbols
Read instruction manual.
Do not use the machine in the rain or
leave it outdoors when it is raining.
Remove battery before adjusting or
cleaning, and before leaving the machine unattended for any period.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away
while operating a power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified
plugs and matching outlets will reduce
risk of electric shock.
Bosch Power Tools
b) Avoid body contact with earthed or
grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges and moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use
of an RCD reduces the risk of electric
3) Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool
while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating
power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate conditions will
reduce personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your finger on the switch or energising power
tools that have the switch on invites accidents.
F 016 L70 729 | (13.12.10) Page 18 Monday, December 13, 2010 12:55 PM
18 | English
d) Remove any adjusting key or wrench before turning the power tool on. A wrench
or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts.
Loose clothes, jewellery or long hair can
be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and
properly used. Use of dust collection can
reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
F 016 L70 729 | (13.12.10)
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are
caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any other battery packs may create a risk of injury
and fire.
c) When battery pack is not in use, keep it
away from other metal objects, like paper clips, coins, keys, nails, screws or
other small metal objects, that can make
a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from
the battery may cause irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that
the safety of the power tool is maintained.
Bosch Power Tools Page 19 Monday, December 13, 2010 12:55 PM
English | 19
Hedge trimmer safety warnings
f Keep all parts of the body away from the
cutter blade. Do not remove cut material
nor hold material to be cut when blades are
moving. Make sure the switch is off when
clearing jammed material. A moment of inattention while operating the hedge trimmer
may result in serious personal injury.
f Carry the hedge trimmer by the handle with
the cutter blade stopped. When transporting or storing the hedge trimmer always fit
the cutting device cover. Proper handling of
the hedge trimmer will reduce possible personal injury from the cutter blades.
f Hold power tool by insulated gripping surfaces only, because the cutter blade may
contact hidden wiring. Cutting blades contacting a “live” wire may make exposed metal
parts of the power tool “live” and could give
the operator an electric shock.
f Keep cable away from cutting area. During
operation the cable may be hidden in shrubs
and can be accidentally cut by the blade.
f Always ensure all handles and guards are
fitted when using the machine. Never attempt to use an incomplete machine or one
fitted with an unauthorized modification.
f Always lubricate the cutting blade with protective spray before use.
f Do not open the battery. Danger of shortcircuiting.
Protect the battery against heat, e. g.,
against continuous intense sunlight,
fire, water, and moisture. Danger of
f Do not short-circuit the battery. There is
danger of explosion.
f In case of damage and improper use of the
battery, vapours may be emitted. Provide
for fresh air and seek medical help in case
of complaints. The vapours can irritate the
respiratory system.
f When the battery is defective, liquid can escape and come into contact with adjacent
components. Check any parts concerned.
Clean such parts or replace them, if required.
Bosch Power Tools
f Use the battery only in conjunction with
your Bosch power tool. This measure alone
protects the battery against dangerous overload.
f Use only original Bosch batteries with the
voltage listed on the nameplate of your
power tool. When using other batteries, e. g.
imitations, reconditioned batteries or other
brands, there is danger of injury as well as
property damage through exploding batteries.
f This tool is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
Safety Warnings for battery chargers
Keep the battery charger away from
rain or moisture. Penetration of water
in the battery charger increases the
risk of an electric shock.
f Do not charge other batteries. The battery
charger is suitable only for charging Bosch
lithium ion batteries within the listed voltage
range. Otherwise there is danger of fire and
f Keep the battery charger clean. Contamination can lead to danger of an electric shock.
f Before each use, check the battery charger,
cable and plug. If damage is detected, do
not use the battery charger. Never open the
battery charger yourself. Have repairs performed only by a qualified technician and
only using original spare parts. Damaged
battery chargers, cables and plugs increase
the risk of an electric shock.
f Do not operate the battery charger on easily inflammable surfaces (e. g., paper, textiles, etc.) or surroundings. The heating of
the battery charger during the charging process can pose a fire hazard.
F 016 L70 729 | (13.12.10) Page 20 Monday, December 13, 2010 12:55 PM
20 | English
f Children should be supervised to ensure
that they do not play with the battery charger.
f Children or persons with mental or physical
limitations may only use the charger under
supervision or after having been instructed.
A thorough introduction reduces operating
errors and injuries.
Products sold in GB only: Your product is fitted
with an BS 1363/A approved electric plug with
internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fitted in its place by an authorised customer service agent. The replacement plug should have the
same fuse rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inserted into a mains socket elsewhere.
Delivery Scope
Carefully remove the garden product from its
packaging and check if the following parts are
– Hedgecutter
– Blade guard
– Operating instructions
Battery and charger are included in certain executions.
When parts are missing or damaged, please contact your dealer.
Product Features
The numbering of the garden product features
refers to the illustration of the garden product
on the graphics page.
1 Cutting blade
2 Front handle guard
Product Description and
Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
While reading the operating instructions, unfold
the graphics page for the garden product and
leave it open.
Intended Use
The machine is intended for cutting and trimming hedges and bushes in domestic use.
F 016 L70 729 | (13.12.10)
3 Front handle with On/Off switch lever
4 Lock-off button for On/Off switch
5 Rear handle with On/Off switch
6 Battery
7 Ventilation slots
8 Blade guard
9 Battery charger
10 LED indicator
11 Serial number
Accessories shown or described are not part of the
standard delivery scope of the product. A complete
overview of accessories can be found in our accessories program.
Bosch Power Tools Page 21 Monday, December 13, 2010 12:55 PM
English | 21
Technical Data
Cordless Hedgecutter
3 600 H49 000
3 600 H49 001
Cutting length
Cutting width
Article number
No-load stroke rate
Weight according to EPTA-Procedure 01/2003
Serial number
See serial number 11 (type plate) on the machine
2 607 336 039
2 607 336 207
2 607 336 039
2 607 336 207
Article number
– 1.3 Ah
– 1.5 Ah
Rated voltage
– 2 607 336 039
– 2 607 336 207
Number of battery cells
– 2 607 336 039
– 2 607 336 207
Run time per battery charge
Battery Charger
AL 2215 CV
AL 2215 CV
2 607 225 471
2 607 225 473
2 607 225 475
2 607 225 471
2 607 225 473
2 607 225 475
Article number
Charging current
Allowable charging temperature range
0– 45
0– 45
Charging period (battery discharged)
Weight according to EPTA-Procedure 01/2003
Protection class
/ II
/ II
Battery Charger
AL 2204 CV
AL 2204 CV
2 607 225 273
2 607 225 275
2 607 225 277
2 607 225 273
2 607 225 275
2 607 225 277
Article number
Charging current
Allowable charging temperature range
0– 45
0– 45
Charging period (battery discharged)
/ II
/ II
Weight according to EPTA-Procedure 01/2003
Protection class
Bosch Power Tools
F 016 L70 729 | (13.12.10) Page 22 Monday, December 13, 2010 12:55 PM
22 | English
Noise/Vibration Information
Measured sound values determined according
to 2000/14/EC.
Typically the A-weighted noise levels of the
product are: Sound pressure level 79 dB(A);
sound power level 87 dB(A). Uncertainty
K =3 dB.
Vibration total values (triax vector sum) determined according to EN 60745:
Vibration emission value ah = 2.5 m/s2, Uncertainty K = 1.5 m/s2.
The vibration emission level given in this information sheet has been measured in accordance
with a standardised test given in EN 60745 and
may be used to compare one tool with another.
It may be used for a preliminary assessment of
The declared vibration emission level represents the main applications of the tool. However
if the tool is used for different applications, with
different accessories or poorly maintained, the
vibration emission may differ. This may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times
when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that
the product described under “Technical Data” is
in conformity with the following standards or
standardization documents: EN 60745 (battery
powered product) and EN 60335 (battery charger) according to the provisions of the directives
2006/95/EC, 2004/108/EC, 2006/42/EC,
2000/14/EC: Guaranteed sound power level
90 dB(A). Conformity assessment procedure according to Annex V.
F 016 L70 729 | (13.12.10)
Equipment category: 25
Technical file at:
Bosch Lawn and Garden Ltd., PT-LG/EAE,
Stowmarket, Suffolk IP14 1EY, England
Dr. Egbert Schneider
Senior Vice President
Dr. Eckerhard Strötgen
Head of Product
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
For Your Safety
f Warning: Switch off and remove battery
from machine before adjusting or cleaning.
f The blades continue to move for a fraction
of a second after the hedgecutter is
switched off.
f Do not touch the moving blades.
Battery Charging
Note: The battery is supplied partially charged.
To ensure full capacity of the battery, completely charge the battery in the battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any
time without reducing its service life. Interrupting the charging procedure does not damage the
Removing the Battery
Press the battery unlocking button and pull out
the battery 6 toward the rear.
Charging Procedure (see figure A)
The charging procedure starts as soon as the
mains plug is plugged into the socket and the
battery is then inserted into the battery charger
Bosch Power Tools Page 23 Monday, December 13, 2010 12:55 PM
English | 23
Firstly, place the battery 6 as shown in the figure
onto the front of the battery charger (n) and
then press the battery 6 down at the rear (o).
To remove the battery, proceed in reverse order.
Due to the intelligent charging method, the
charging condition of the battery is automatically detected and the battery is charged with the
optimum charging current, depending on battery temperature and voltage.
This gives longer life to the battery and always
leaves it fully charged when kept in the charger
for storage.
Note: The charging procedure is only possible
when the battery temperature is within the allowable charging temperature range, see section “Technical Data”.
Flashing Battery Charge Indicator 10
The charging procedure is signalled by a flashing battery
charge indicator 10.
Continuous Lighting of the Battery Charge Indicator 10
Continuous lighting of the
battery charge indicator 10
indicates that the battery is
fully charged or that the temperature of the battery is not within the allowable charging temperature range, and cannot be
charged for this reason. The battery is charged
as soon as the allowable charging temperature
range is reached.
When the battery is not inserted, continuous
lighting of the battery charge indicator 10 indicates that the mains plug is inserted in the socket and that the battery charger is ready for operation.
Charging Advice
With continuous or several repetitive charging
cycles without interruption, the charger can
warm up. This is not meaningful and does not indicate a technical defect of the battery charger.
A significantly reduced working period after
charging indicates that the battery is used and
must be replaced.
The battery is equipped with a NTC temperature
control which allows charging only within a temperature range of between 0 °C and 45 °C. A
long battery service life is achieved in this manner.
The “Electronic Cell Protection (ECP)” protects
the lithium ion battery against deep discharging.
When the battery is run down or discharged, the
garden product is shut off by means of a protective circuit: The blade no longer moves.
Do not continue to press the
On/Off switch after the garden
product has been automatically switched off.
The battery can be damaged.
Initial Operation
Inserting the Battery (see figure A)
Insert the battery into the machine as shown.
The battery must be felt to engage.
Switching On (see figure B)
n Press and hold the On/Off switch 5 on the
rear handle.
o Pull the safety switch 4 upward.
p Then press the front On/Off switch 3.
Switching Off
Release the front 3 or rear 5 On/Off switch.
Working Advice (see figures C–E)
f Warning: Hold the hedgecutter away from
yourself using both hands. Stand in a secure and stable position.
f Always lubricate the cutting blade with protective spray before use.
Cuts stems up to 15 mm in thickness (max.).
When cutting, move steadily along the line of
cut, so that stems are fed directly into the cutter
blades. The double edge cutting blade enables
cutting in either direction, or with a side to side
Cut the sides of the hedge first, then the top.
Bosch Power Tools
F 016 L70 729 | (13.12.10) Page 24 Monday, December 13, 2010 12:55 PM
24 | English
To cut the sides straightly, we recommend cutting from bottom to top in the direction of
growth. Younger stems tend to move outwards
when cutting them from top to bottom, resulting
in shallow patches or holes in the hedge.
To reach a level finish, fasten a piece of string
along the length of the hedge at the required
height and use as an alignment guide. Cut the
hedge just above the string.
Always take care to avoid cutting into objects
such as wire, which could cause damage to the
cutting blades and the drive.
Anti Blocking
The garden product has a patented feature
which works as follows:
If the blade stalls on a tough material, the load
of the motor increases. The intelligent microelectronics senses this overload condition and
repeatedly reverses the motor, in order to prevent stalling and to cut the material through.
This audible reversing cut action continues for
up to 3 s.
After cutting through, the garden product continues in its normal mode, or in case the overload condition continues the blades automatically stop in the open position (e. g. in case a
piece of metal fence accidentally blocks the garden product).
The following chart lists problem symptoms, possible causes and corrective action, if your garden
product does not operate properly. If these do not identify and correct the problem, contact your
service agent.
f Warning: Switch off and remove the battery prior to any troubleshooting.
Possible Cause
Corrective Action
Hedgecutter does
not operate
Battery discharged
Recharge battery; also see “Battery
Hedgecutter operates intermittently
Internal wiring of garden product
Contact Service Agent
On/Off switch defective
Contact Service Agent
Safety switch not activated correctly see “Initial Operation”
Motor reverses repeatedly then stalls see “Working Advice” (Anti Blocking)
after 3 s.
Motor runs but
blades remain stationary
Cutting blade hot
Blade will not move
F 016 L70 729 | (13.12.10)
Internal fault
Contact Service Agent
Cutting blade blunt
Have blade sharpened
Cutting blade has dents
Have blade inspected/overhauled
Too much friction, due to lack of lubricant
Apply lubricant spray
Battery discharged
Recharge battery; also see “Battery
Garden product defective
Contact Service Agent
Garden product defective
Contact Service Agent
Bosch Power Tools Page 25 Monday, December 13, 2010 12:55 PM
English | 25
Possible Cause
Corrective Action
Cutting time per bat- Too much friction, due to lack of lutery charge too low bricant
Blade needs cleaning
Continuous lighting
of the battery
charge indicator 10
No charging procedure possible
Apply lubricant spray
Clean blade
Poor cutting technique
see “Working Advice”
Battery not fully charged
Recharge battery; also see “Battery
Battery not (properly) inserted
Properly insert battery into battery
Battery contacts contaminated
Clean the battery contacts (e.g. by
inserting and removing the battery
several times) or replace the battery
Battery defective
Replace the battery
The blades are running slow or the anti
blocking feature is
not functioning
Battery discharged
Recharge battery; also see “Battery
Battery stored outside of battery
Allow battery to warm naturally to
room temperature (within battery
operating temperature 0 – 45 °C)
Battery charge indicator 10 does not
light up
Mains plug of battery charger not
plugged in (properly)
Insert mains plug (fully) into the
socket outlet
Socket outlet, mains cable or battery
charger defective
Check the mains voltage; have the
battery charger checked by an authorised after-sales service agent for
Bosch power tools
Maintenance and Service
Maintenance and Cleaning
f Warning: Before any work on the machine
itself, remove the battery from the machine.
Note: To ensure long and reliable service, carry
out the following maintenance regularly.
Regularly check for obvious defects such as
loose fixings, and worn or damaged components.
Check that covers and guards are undamaged
and correctly fitted. Carry out necessary maintenance or repairs before using.
Bosch Power Tools
If the garden product should happen to fail despite the care taken in manufacture and testing,
repair should be carried out by an authorised
customer service agent for Bosch garden products.
In all correspondence and spare parts orders,
please always include the 10-digit article
number given on the type plate of the garden
After Use/Storage
f Warning: Switch the machine off and remove the battery. Ensure battery is removed before storage.
Clean the exterior of the machine thoroughly using a soft brush and cloth. Do not use water, solvents or polishes. Remove all debris, especially
from the ventilation slots 7 of the motor.
F 016 L70 729 | (13.12.10) Page 26 Monday, December 13, 2010 12:55 PM
26 | English
Always lubricate the cutting blade with protective spray before storage.
Store the hedgecutter in a secure, dry place out
of the reach of children. Do not place other objects on top of the machine.
The battery should be stored between 0 °C and
45 °C.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concerning maintenance and repair of your
product as well as spare parts. Exploded views
and information on spare parts can also be
found under:
Our customer service representatives can answer your questions concerning possible applications and adjustment of products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
F 016 L70 729 | (13.12.10)
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
Republic of South Africa
Customer service
Hotline: +27 (011) 6 51 96 00
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Tel.: +27 (011) 4 93 93 75
Fax: +27 (011) 4 93 01 26
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Tel.: +27 (031) 7 01 21 20
Fax: +27 (031) 7 01 24 46
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Tel.: +27 (021) 5 51 25 77
Fax: +27 (021) 5 51 32 23
Bosch Headquarters
Midrand, Gauteng
Tel.: +27 (011) 6 51 96 00
Fax: +27 (011) 6 51 98 80
Bosch Power Tools Page 27 Monday, December 13, 2010 12:55 PM
English | 27
Dispatch batteries only when the housing is undamaged. Tape or mask off open contacts and
pack up the battery in such a manner that it cannot move around in the packaging.
When dispatching lithium-ion batteries, compulsory labeling may be required. Please observe
the respective national regulations.
Battery packs/batteries:
Please observe the instructions in section “Transport”,
page 27.
Subject to change without notice.
The garden product, accessories and packaging
should be sorted for environmental-friendly recycling.
Do not dispose of garden products, battery
chargers and batteries/rechargeable batteries
into household waste!
Only for EC countries:
According to the European law
2002/96/EC, electrical and electronic equipments that are no
longer usable, and according to
the European law 2006/66/EC,
defective or used battery
packs/batteries, must be collected separately
and disposed of in an environmentally correct
Batteries no longer suitable for use can be
directly returned at:
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
Bosch Power Tools
F 016 L70 729 | (13.12.10)
Download PDF