Asus Motherboard P4GE-V User guide

Asus Motherboard P4GE-V User guide
User Guide
First Edition
September 2002
Copyright © 2002 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form or by any means, except documentation kept by the purchaser for
backup purposes, without the express written permission of ASUSTeK COMPUTER INC.
Product warranty or service will not be extended if: (1) the product is repaired, modified or
altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2)
the serial number of the product is defaced or missing.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification or
explanation and to the owners’ benefit, without intent to infringe.
FCC/CDC statements ..................................................................... vi
Safety information ......................................................................... vii
About this guide ............................................................................ viii
How this guide is organized ................................................ viii
Conventions used in this guide ............................................. ix
Where to find more information ............................................. ix
ASUS contact information ............................................................... x
P4GE-V specifications summary .................................................... xi
Chapter 1: Product introduction
Welcome! ........................................................................... 1-1
Package contents ............................................................... 1-1
Special features .................................................................. 1-2
Motherboard overview ........................................................ 1-6
1.4.1 Major components ................................................. 1-6
1.4.2 Core specifications ................................................ 1-8
Chapter 2: Hardware information
Motherboard installation ..................................................... 2-1
2.1.1 Placement direction ............................................... 2-1
2.1.2 Screw holes ........................................................... 2-1
Motherboard layout ............................................................ 2-2
Before you proceed ............................................................ 2-3
Central Processing Unit (CPU) ........................................... 2-4
2.4.1 Overview ................................................................ 2-4
2.4.2 Installing the CPU .................................................. 2-5
2.4.3 Installing the heatsink and fan ............................... 2-7
2.4.4 Connecting the CPU fan cable .............................. 2-9
System memory ............................................................... 2-10
2.5.1 Overview .............................................................. 2-10
2.5.2 Memory configurations .........................................2-11
2.5.3 Installing a DIMM ................................................. 2-12
2.5.4 Removing a DIMM ............................................... 2-12
Expansion slots ................................................................ 2-13
2.6.1 Installing an expansion card ................................ 2-13
2.6.2 Configuring an expansion card ............................ 2-13
2.6.3 PCI slots .............................................................. 2-15
2.6.4 AGP slot ............................................................... 2-15
Jumpers ............................................................................ 2-16
Connectors ....................................................................... 2-18
Chapter 3: Powering up
Starting up for the first time ................................................ 3-1
Vocal POST Messages ...................................................... 3-2
Powering off the computer ................................................. 3-4
Chapter 4: BIOS setup
Managing and updating your BIOS .................................... 4-1
4.1.1 Using ASUS EZ Flash to update the BIOS ............ 4-1
4.1.2 Using AFLASH to update the BIOS ....................... 4-3
BIOS Setup program .......................................................... 4-7
4.2.1 BIOS menu bar ...................................................... 4-8
4.2.2 Legend bar ............................................................. 4-8
Main Menu ........................................................................ 4-10
4.3.1 Primary and Secondary Master/Slave ................. 4-12
4.3.2 Keyboard Features .............................................. 4-16
Advanced Menu ............................................................... 4-17
4.4.1 Chip Configuration ............................................... 4-20
4.4.2 I/O Device Configuration ...................................... 4-24
4.4.3 PCI Configuration ................................................ 4-26
Power Menu ..................................................................... 4-29
4.5.1 Power Up Control ................................................ 4-31
4.5.2 Hardware Monitor ................................................ 4-33
Boot Menu ........................................................................ 4-35
Exit Menu ......................................................................... 4-37
Chapter 5: Software support
Install an operating system ................................................. 5-1
Support CD information ...................................................... 5-1
5.2.1 Running the support CD ........................................ 5-1
5.2.2 Drivers menu ......................................................... 5-2
5.2.3 Utilities menu ......................................................... 5-5
5.2.4 ASUS Contact Information ..................................... 5-6
5.2.5 Other information ................................................... 5-7
Software information .......................................................... 5-9
5.3.1 ASUS Update ........................................................ 5-9
5.3.2 ASUS MyLogo2™ ................................................ 5-10
5.3.3 ASUS PC Probe .................................................. 5-12
5.3.4 Winbond Voice Editor .......................................... 5-17
5.3.5 Multi-channel audio feature ................................. 5-21
FCC/CDC statements
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the
following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the
graphics card is required to assure compliance with FCC regulations.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from
the electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that
the power cables for the devices are unplugged before the signal
cables are connected. If possible, disconnect all power cables from the
existing system before you add a device.
• Before connecting or removing signal cables from the motherboard,
ensure that all power cables are unplugged.
• Seek professional assistance before using an adpater or extension
cord. These devices could interrupt the grounding circuit.
• Make sure that your power supply is set to the correct voltage in your
area. If you are not sure about the voltage of the electrical outlet you
are using, contact your local power company.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safety
• Before installing the motherboard and adding devices on it, carefully
read all the manuals that came with the package.
• Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the
product in any area where it may become wet.
• Place the product on a stable surface.
• If you encounter technical problems with the product, contact a
qualified service technician or your retailer.
About this guide
This user guide contains the information you need when installing the
ASUS P4GE-V motherboard.
How this guide is organized
This manual contains the following parts:
• Chapter 1: Product introduction
This chapter describes the features of the P4GE-V motherboard. It
includes brief descriptions of the special attributes of the motherboard
and the new technology it supports.
• Chapter 2: Hardware information
This chapter lists the hardware setup procedures that you have to
perform when installing system components. It includes description of
the switches, jumpers, and connectors on the motherboard.
• Chapter 3: Powering up
This chapter describes the power up sequence and gives information
on the BIOS beep codes.
• Chapter 4: BIOS setup
This chapter tells how to change system settings through the BIOS
Setup menus. Detailed descriptions of the BIOS parameters are also
• Chapter 5: Software support
This chapter describes the contents of the support CD that comes with
the motherboard package.
• Index
This part contains an alphabetical list of the topics found in this
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the
following symbols used throughout this manual.
WARNING: Information to prevent injury to yourself when trying
to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Information that you MUST follow to complete a
NOTE: Tips and additional information to aid in completing a task.
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1. ASUS Websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. The ASUS websites are listed in the
ASUS Contact Information on page x.
2. Optional Documentation
Your product package may include optional documentation, such as
warranty flyers, that may have been added by your dealer. These
documents are not part of the standard package.
ASUS contact information
General Tel:
General Fax:
General Email:
150 Li-Te Road, Peitou, Taipei, Taiwan 112
[email protected]
Technical Support
MB/Others (Tel):
Notebook (Tel):
Desktop/Server (Tel):
Support Fax:
Support Email:
Web Site:
+886-2-2890-7121 (English)
+886-2-2890-7122 (English)
+886-2-2890-7123 (English)
[email protected]
General Fax:
General Email:
6737 Mowry Avenue, Mowry Business Center,
Building 2, Newark, CA 94560, USA
[email protected]
Technical Support
Support Fax:
General Support:
Web Site:
Support Email:
[email protected]
General Fax:
General Email:
Harkortstr. 25, 40880 Ratingen, BRD, Germany
[email protected] (for marketing requests only)
Technical Support
Support Hotline:
Support Fax:
Support (Email):
Web Site:
MB/Others: +49-2102-9599-0
Notebook: +49-2102-9599-10
+49-2102-9599-11 (for online support)
P4GE-V specifications summary
Socket 478 for Intel® Pentium® 4 / Celeron 3.0+ GHz
On-die 512KB/256KB L2 cache with full speed
Intel® Hyper-Threading technology ready
New power design for up to 3.06 GHz or faster speed
Intel 82845GE GMCH
Intel 82801DB ICH4
Front Side Bus (FSB)
533/400 MHz
3 x 184-pin DDR DIMM sockets for up to 2GB memory
Supports PC2700/PC2100 (FSB533), or PC2100/PC1600
(FSB400) unbuffered non-ECC DDR DIMMs
Expansion slots
1 x AGP 4X (1.5V only)
6 x PCI (includes one ASUS BlueMagic PCI slot)
Integrated 3D graphics controller in 82845GE
Supports ASUS DVI-845 graphics card (purchased separately)
2 x UltraDMA 100/66/33 connectors
ADI AD1980 6-channel audio CODEC
Broadcom® BCM4401 Fast Ethernet controller
Special features
ASUS JumperFree™ mode
ASUS POST Reporter™
C.P.R. (CPU Parameter Recall)
CrashFree BIOS
Power Loss Restart
SFS (Stepless Frequency Selection)
CPU throttle
Adjustable CPU VCORE, memory, and AGP voltages
Multi-language BIOS
AGP warning LED
Rear panel I/O
1 x Parallel port
1 x Serial port
1 x Video port
1 x PS/2 keyboard port
1 x PS/2 mouse port
4 x USB 2.0/USB 1.1 ports
1 x RJ-45 port
Line In/Line Out/Microphone ports
(continued on the next page)
P4GE-V specifications summary
Internal I/O
1 x USB 2.0/1.1 connector for 2 additional USB ports
CPU/Power/Chassis fan connectors
20-pin/4-pin ATX 12V power connectors
IDE LED/Power LED connectors
Chassis intrusion, SMBus, and SIR connectors
GAME/MIDI connector
S/PDIF Out connector
CD/AUX/Modem audio connectors
Front panel audio connector
BIOS features
4Mb Flash ROM, Award BIOS, TCAV, PnP, DMI2.0, WfM2.0,
SM BIOS2.3, Multi-language BIOS, ASUS EZ Flash,
CrashFree BIOS, C.P.R. (CPU Parameter Recall)
Industry standard
PCI 2.2, USB 2.0
WfM 2.0. DMI 2.0, WOL/WOR by PME, chassis intrusion,
Form Factor
ATX form factor: 12 in x 9.0 in (30.5 cm x 22.9 cm)
Support CD contents
Device drivers
ASUS LiveUpdate
Trend Micro™ PC-cillin 2002 anti-virus software
* Specifications are subject to change without notice.
Chapter 1
This chapter describes the features of the
P4GE-V motherboard. It includes brief
explanations of the special attributes of the
motherboard and the new technology it
Product introduction
Chapter summary
Welcome! ........................................................ 1-1
Package contents .......................................... 1-1
Special features ............................................. 1-2
Motherboard overview ................................... 1-6
ASUS P4GE-V motherboard
Thank you for buying the ASUS® P4GE-V motherboard!
The ASUS P4GE-V motherboard delivers a host of new features and latest
technologies making it another standout in the long line of ASUS quality
The P4GE-V incorporates the Intel® Pentium® 4 Processor in 478-pin
package coupled with the Intel® 82845GE chipset to set a new benchmark
for an effective desktop platform solution.
Supporting up to 2GB of system memory with PC2700/2100/1600 DDR
SDRAM, high-resolution graphics via an AGP 4X slot, USB 2.0, 3D video,
and 6-channel audio features, the P4GE-V is your perfect vehicle to get
ahead in the world of power computing!
Before you start installing the motherboard, and hardware devices on it,
check the items in your package with the list below.
Package contents
Check your P4GE-V package for the following items.
ASUS P4GE-V motherboard
ATX form factor: 12 in x 9.0 in (30.5 cm x 22.9 cm)
ASUS P4GE-V series support CD
ASUS USB 2.0/GAME module (for audio models only)
ASUS S/PDIF module (for audio models only)
80-conductor ribbon cables for UltraDMA/66/100 IDE drives
40-conductor IDE cable
Ribbon cable for a 3.5-inch floppy drive
I/O shield
Bag of extra jumper caps
User Guide
Quick Setup Guide and Reference Card (for retail boxes only)
Jumpers and Connectors Sticker (for retail boxes only)
If any of the above items is damaged or missing, contact your retailer.
ASUS P4GE-V motherboard user guide
Special features
Latest processor technology
The P4GE-V motherboard supports the latest Intel® Pentium® 4 Processor via
a 478-pin surface mount ZIF socket. The Pentium 4 processor with 512KB L2
cache on 0.13 micron process includes a 533/400 MHz system bus and
features the new Hyper-Threading technology and FMB2 power design
that allow up to 3.0+ GHz core frequencies for up to 4.2GB/s data transfer
rates. See page 2-4.
DDR memory support
Employing the Double Data Rate (DDR) memory technology, the P4GE-V
motherboard supports up to 2GB of system memory using PC2700/
PC2100/PC1600 DDR DIMMs. The ultra-fast 333MHz memory bus
delivers the required bandwidth for the latest 3D graphics, multimedia, and
Internet applications. See page 2-10.
Onboard LAN solution (on LAN models only)
The motherboard mounts the BroadCom® BCM4401 chipset to support
10BASE-T/100BASE-TX networking protocol.
USB 2.0 technology
The motherboard implements the new Universal Serial Bus (USB) 2.0
specification, extending the connection speed from 12 Mbps on USB 1.1
to a fast 480 Mbps on USB 2.0. The higher bandwidth of USB 2.0 allows
connection of devices such as high resolution video conferencing
cameras, next generation scanners and printers, and fast storage units.
USB 2.0 is backward compatible with USB 1.1. See page 2-23.
6-channel digital audio (on audio models only)
The ADI AD1980 AC ‘97 audio CODEC is onboard to provide 6-channel
audio playback for 5.1 surround sound, over 90dB dynamic range, and
stereo Mic PREAMP. A digital audio connector is onboard to accommodate
the bundled Sony/Philips Digital Interface (S/PDIF) Out module. See page
Chapter 1: Product introduction
Integrated VGA
The Intel 845GE Graphics Memory Controller Hub (GMCH) has an
integrated graphics controller that delivers 3D, 2D, and video capabilities.
The GMCH video engines support video conferencing and other video
applications. The Brookdale-G GMCH is compliant with the Digital Visual
Interface (DVI) Specification Rev. 1.0, and supports high-speed interface
to a digital display when a DVI-compliant external device is present. See
pages 2-15 and 4-22.
BlueMagic PCI slot
The ASUS proprietary BlueMagic slot is onboard to support future ASUS
function cards that are also compliant to PCI specification. See page 1-9.
C.P.R. (CPU Parameter Recall)
The C.P.R. feature of the motherboard BIOS allows automatic re-setting to
the BIOS default settings in case the system hangs due to overclocking.
When the system hangs due to overclocking, C.P.R. eliminates the need to
open the system chassis and clear the RTC data. Simply shut down and
reboot the system, and BIOS automatically restores the CPU default
settings for each parameter. See page 2-17.
This patented ASUS technology lets you use your existing power supply
rather than buying a new ATX 12V power supply. The ASUS EZ Plug™ is
a 4-pin auxillary +12V connector mounted on the motherboard that
connects a regular 4-pin device power connector from the power supply.
This connector is necessary to provide the additional power required by
the P4 CPU. See page 2-21.
ASUS POST Reporter™
P4GE-V offers a new exciting feature called the ASUS POST Reporter™
to provide friendly voice messages and alerts during the Power-On SelfTests (POST). Through an added external speaker, you will hear the
messages informing you of the system boot status and causes of boot
errors, if any. The bundled Winbond Voice Editor software allows you to
customize the voice messages, and provides multi-language support. See
pages 3-1, 4-25, and 5-17.
ASUS P4GE-V motherboard user guide
ASUS MyLogo2™
This new feature present in the P4GE-V motherboard allows you to
personalize and add style to your system with customizable boot logos.
See details on page 5-10.
ASUS Multi-language BIOS
The multi-language BIOS allows you to select the language of your choice
from the available options. The localized BIOS menus allow you to
configure easier and faster. Visit the ASUS website for information on the
supported languages. See page 4-11.
With the ASUS EZ Flash, you can easily update the system BIOS even
before loading the operating system. No need to use a DOS-based utility
or boot from a floppy disk. See page 4-1.
ASUS Q-Fan technology
The ASUS Q-Fan technology smartly adjusts the fan speeds according to
the system loading to ensure quiet, cool, and efficient operation. See page
CrashFree BIOS
This feature allows you to restore the original BIOS data from a floppy disk
in cases when the BIOS codes and data are corrupted. This protection
eliminates the need to buy a replacement ROM chip.
Chapter 1: Product introduction
• adjustable CPU frequency multiple in BIOS using the ASUS
JumperFree™ solution
• C.P.R. (CPU Parameter Recall)
• adjustable FSB/DDR ratio
• Fixed AGP/PCI ratio
• adjustable CPU VCORE , and DDR memory and AGP voltages
• Stepless Frequency Selection (SFS) for fine-tuning system bus
frequency from 100MHz up to 200MHz at 1MHz increments
See page 4-17.
Temperature, fan, and voltage monitoring
The CPU temperature is monitored by the ASUS ASIC to prevent
overheating and damage. The system fan rotations per minute (RPM) is
monitored for timely failure detection. The system voltage levels are
monitored to ensure stable supply of current for critical components. See
page 4-33.
ACPI ready
The Advanced Configuration power Interface (ACPI) provides more energy
saving features for operating systems that support OS Direct Power
Management (OSPM). See page 4-30.
Chassis intrusion detection
The motherboard supports chassis intrusion monitoring through the ASUS
ASIC. A chassis intrusion event is retained in CMOS for more protection.
See page 2-20.
ASUS P4GE-V motherboard user guide
Motherboard overview
Before you install the P4GE-V motherboard, familiarize yourself with its
physical configuration and available features to facilitate the motherboard
installation and future upgrades. A sufficient knowledge of the motherboard
specifications will also help you avoid mistakes that may damage the
board and its components.
1.4.1 Major components
The following are the major components of the P4GE-V motherboard as
pointed out in the picture on page 1-7.
ATX 12V connector
19. AGP slot
CPU socket
20. PS/2 mouse port
North Bridge controller
21. Parallel port
DDR DIMM sockets
22. RJ-45 port (optional)
ASUS EZ Plug™ 12V connector
23. Line In jack
ATX power connector
24. Line Out jack
Floppy disk connector
25. Microphone jack
IDE connectors
26. USB 2.0 ports 3 and 4
South Bridge controller
27. Video port
10. Speech controller
28. Serial port
29. USB 2.0 ports 1 and 2
Flash ROM
12. Standby power LED
30. Keyboard port
14. Super I/O controller
15. PCI slots
16. Audio CODEC
17. LAN controller (optional)
AGP warning LED
See page 1-8 for the specifications of each component. Refer to
Chapter 2 for detailed information on the components.
Chapter 1: Product introduction
13 12
ASUS P4GE-V motherboard user guide
1.4.2 Core specifications
ATX 12V connector. This power connector connects the 4-pin 12V
plug from the ATX 12V power supply.
CPU socket. A 478-pin surface mount, Zero Insertion Force (ZIF)
socket for the Intel® Pentium® 4 Processor, with 533/400 MHz system
bus that allows 4.3GB/s and 3.2GB/s data transfer rates, respectively.
North bridge controller. The Intel® 845GE Graphics Memory
Controller Hub (GMCH) provides the processor interface with 533/400
MHz frequency, system memory interface at 333/266MHz operation,
and 1.5V AGP interface that supports AGP 2.0 specification including
4X Fast Write protocol. The integrated graphics accelerator delivers
3D/2D video capabilities and a high bandwidth access to graphics
data in the system memory at 2.2GB/s or 1.6GB/s. The GMCH
interconnects to the south bridge ICH4 via the Intel® proprietary Hub
DDR DIMM sockets. These three 184-pin DIMM sockets support up
to 2GB system memory using unbuffered non-ECC PC2700/
PC2100/PC1600 DDR DIMMs.
ASUS EZ Plug™ +12V connector. This ASUS patented auxilliary
power connector is used if you don’t have an ATX +12V power supply.
Connect a 4-pin device connector from a standard power supply to
this connector to provide sufficient power to the CPU.
ATX power connector. This 20-pin connector connects to an ATX
+12V power supply. The power supply must have at least 1A on the
+5V standby lead (+5VSB).
Floppy disk connector. This connector accommodates the provided
ribbon cable for the floppy disk drive. One side of the connector is
slotted to prevent incorrect insertion of the floppy disk cable.
IDE connectors. These dual-channel bus master IDE connectors
support Ultra DMA/100/66, PIO Modes 3 & 4 IDE devices. Both the
primary (blue) and secondary (black) connectors are slotted to prevent
incorrect insertion of the IDE ribbon cable.
South bridge controller. The fourth-generation Intel I/O Controller
Hub (ICH4) is a subsystem that integrates various I/O functions
including 2-channel ATA/100 bus master IDE controller, up to six USB
2.0/1.1 ports, I/O APIC, SMBus 2.0 controller, LPC interface, AC’97 2.2
interface, and PCI 2.2 interface. The ICH4 also contains the necessary
arbitration and buffering for efficient utilization of these interfaces.
Chapter 1: Product introduction
Speech controller. This Winbond speech controller supports the
ASUS POST Reporter™ for configurable vocal POST alerts.
Flash ROM. This 4Mb firmware contains the programmable BIOS
Standby power LED. This LED lights up if there is a standby power
on the motherboard. This LED acts as a reminder to turn off the
system power before plugging or unplugging devices.
ASUS ASIC. This chip performs multiple system functions that include
hardware and system voltage monitoring, IRQ routing, among others.
Super I/O controller. This Low Pin Count (LPC) interface provides the
commonly used Super I/O functionality. The chipset supports a highperformance floppy disk controller for a 360K/720K/1.44M/2.88M
floppy disk drive, a multi-mode parallel port, two standard compatible
UARTs, a Standard Infrared (SIR), and a Flash ROM interface.
PCI slots. These six 32-bit PCI 2.2 expansion slots support bus
master PCI cards like SCSI or LAN cards with 133MB/s maximum
throughput. The ASUS proprietary BlueMagic PCI slot (blue slot)
supports future ASUS function cards compliant to PCI specification.
Audio CODEC. The ADI AD1980 is an AC’97 CODEC that allows
6-channel audio playback. The audio CODEC provides six DAC
channels for 5.1 surround sound, S/PDIF output, AUX and Line In
stereo inputs, integrated headphone amplifier, greater than 90dB
dynamic range, and stereo Mic PREAMP support.
LAN controller. The BroadCom BCM4401 onboard supports
10BASE-T/100BASE-TX Fast Ethernet networking.
(on LAN models only)
AGP warning LED. Serving as a smart burn-out protection for the
motherboard, this red LED lights up if you plug in any 3.3V AGP card
into the AGP slot. When this LED is lit, there is no way you can turn
on the system power even if you press the power button.
AGP slot. This Accelerated Graphics Port (AGP) slot supports 1.5V
AGP4X mode graphics cards for 3D graphical applications.
PS/2 mouse port. This green 6-pin connector is for a PS/2 mouse.
Parallel port. This 25-pin port connects a parallel printer, a scanner,
or other devices.
RJ-45 port. This port allows connection to a Local Area Network
(LAN) through a network hub. (on LAN models only)
ASUS P4GE-V motherboard user guide
Line In jack. This Line In (light blue) jack connects a tape player or
other audio sources. In 6-channel mode, the function of this jack
becomes Bass/Center.
Line Out jack. This Line Out (lime) jack connects a headphone or a
speaker. In 6-channel mode, the function of this jack becomes Front
Speaker Out.
Microphone jack. This Mic (pink) jack connects a microphone. In 6channel mode, the function of this jack becomes Rear Speaker Out.
USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB)
ports are available for connecting USB 2.0 devices.
Video port. This port is for a VGA monitor or other VGA-compatible
Serial port. This 9-pin COM1 port is for pointing devices or other
serial devices.
USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB)
ports are available for connecting USB 2.0 devices.
PS/2 keyboard port. This purple connector is for a PS/2 keyboard.
Chapter 1: Product introduction
Chapter 2
This chapter describes the hardware setup
procedures that you have to perform when
installing system components. It includes
details on the switches, jumpers, and
connectors on the motherboard.
Hardware information
Chapter summary
Motherboard installation ............................... 2-1
Motherboard layout ....................................... 2-2
Before you proceed ....................................... 2-3
Central Processing Unit (CPU) ..................... 2-4
System memory ........................................... 2-10
Expansion slots ........................................... 2-13
Jumpers ........................................................ 2-16
Connectors ................................................... 2-18
ASUS P4GE-V motherboard
Motherboard installation
Before you install the motherboard, study the configuration of your chassis
to ensure that the motherboard fits into it. The P4GE-V uses the ATX form
factor that measures 12 inches x 9.0 inches (30.5 x 22.9 cm).
Make sure to unplug the power cord before installing or removing the
motherboard. Failure to do so may cause you physical injury and
damage motherboard components.
2.1.1 Placement direction
When installing the motherboard, make sure that you place it into the
chassis in the correct orientation. The edge with external ports goes to the
rear part of the chassis as indicated in the image below.
2.1.2 Screw holes
Place seven (7) screws into the holes indicated by circles to secure the
motherboard to the chassis.
Do not overtighten the screws! Doing so may damage the
Place this side towards
the rear of the chassis
ASUS P4GE-V motherboard user guide
Motherboard layout
Intel 845GE
USB2.0 Top:
T:USB3 RJ-45
Controller Hub
ATX Power Connector
4 5
2 3
0 1
DDR DIMM3 (64/72 bit, 184-pin module)
DDR DIMM2 (64/72 bit, 184-pin module)
DDR DIMM1 (64/72 bit, 184-pin module)
Top:Line In
Center:Line Out
Below:Mic In
Accelerated Graphics Port (AGP)
Intel I/O
30.5cm (12.0in)
Socket 478
T: Mouse
B: Keyboard
22.86cm (9.0in)
CR2032 3V
Lithium Cell
CMOS Power
PCI6 / BlueMagic PCI Slot
The audio and LAN features are optional. These components are
grayed out in the above motherboard layout.
Chapter 2: Hardware information
Before you proceed
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any
2. Use a grounded wrist strap or touch a safely grounded object or to
a metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity.
3. Hold components by the edges to avoid touching the ICs on them.
4. Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
5. Before you install or remove any component, ensure that the
ATX power supply is switched off or the power cord is
detached from the power supply. Failure to do so may cause
severe damage to the motherboard, peripherals, and/or
When lit, the green LED (SB_PWR1) indicates that the system is ON,
in sleep mode, or in soft-off mode, a reminder that you should shut
down the system and unplug the power cable before removing or
plugging in any motherboard component.
The red LED (AGP_WARN1) is a smart protection from motherboard
burn out caused by an incorrect AGP card. If you plug in any 3.3V AGP
card into the 1.5V AGP slot, this LED lights up thus preventing the
system to power up. This LED remains off if you plug in a 1.5V AGP
AGP Card
AGP Card
P4GE-V Onboard LED
ASUS P4GE-V motherboard user guide
Central Processing Unit (CPU)
2.4.1 Overview
The motherboard comes with a surface mount 478-pin Zero Insertion
Force (ZIF) socket. The socket is designed for the Intel® Pentium® 4
Processor in the 478-pin package with 512KB L2 cache on 0.13 micron
process. This processor includes the Intel® NetBurst™ micro-architecture
that features the hyper-pipelined technology, rapid execution engine,
533/400MHz system bus, and execution trace cache. Together, these
attributes improve system performance by allowing higher core
frequencies, faster execution of integer instructions, and data transfer
rates of 3.2GB/s and 4.2GB/s.
Gold Mark
Note in the illustration that the CPU
has a gold triangular mark on one
corner. This mark indicates the
processor Pin 1 that should match a
specific corner of the CPU socket.
Incorrect installation of the CPU into the socket may bend the pins and
severely damage the CPU!
Notes on Intel® Hyper-Threading technology
1. This motherboard supports Intel Pentium 4 CPUs with HyperThreading technology.
2. Hyper-Threading technology is supported under Windows XP and
Linux 2.4.x (kernel) and later versions only. Under Linux, use the
Hyper-Threading compliler to compile the code. If you are using any
other operating systems, disable the Hyper-Threading Techonology
item in BIOS to ensure system stability and performance.
3. For more information on Hyper-Threading technology, visit
To use the Hyper-Threading technology on this motherboard:
1. Buy an Intel Pentium 4 CPU that supports Hyper-Threading
technology. Install the CPU.
2. Power up the system and enter BIOS Setup (see Chapter 4). Under
the Advanced Menu, make sure that the item Hyper-Threading
Technology is set to Enabled. The item appears only if you installed a
CPU that supports Hyper-Threading techonology.
Chapter 2: Hardware information
2.4.2 Installing the CPU
Follow these steps to install a CPU.
1. Locate the 478-pin ZIF socket on the motherboard.
2. Unlock the socket by pressing the lever sideways, then lift it up to a
90°-100° angle.
Socket Lever
90 - 100
Make sure that the socket lever is lifted up to 90°-100° angle,
otherwise the CPU does not fit in completely.
ASUS P4GE-V motherboard user guide
3. Position the CPU above the socket such that its marked corner
matches the base of the socket lever.
4. Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct orientation. DO NOT force the CPU
into the socket to prevent bending the pins and damaging the CPU!
Gold Mark
5. When the CPU is in place, push down the socket lever to secure the
CPU. The lever clicks on the side tab to indicate that it is locked.
Chapter 2: Hardware information
2.4.3 Installing the heatsink and fan
The Intel® Pentium® 4 Processor requires a specially designed heatsink
and fan assembly to ensure optimum thermal condition and performance.
When you buy a boxed Intel Pentium 4 Processor, the package
includes the heatsink, fan, and retention mechanism.
In case you buy a CPU separately, make sure that you use only Intel
certified heatsink and fan.
Follow these steps to install the CPU heatsink and fan.
1. Place the heatsink on top of the installed CPU, making sure that the
heatsink fits properly on the retention module base.
The retention module base is already installed on the motherboard
upon purchase.
You do not have to remove the retention module base when installing
the CPU or installing other motherboard components.
CPU Heatsink
Retention Module Base
Your boxed Intel Pentium 4 Processor package should come with
installation instructions for the CPU, heatsink, and the retention
mechanism. If the instructions in this section do not match the CPU
documentation, follow the latter.
ASUS P4GE-V motherboard user guide
2. Position the fan with the retention mechanism on top of the heatsink.
Align and snap the four hooks of the retention mechanism to the holes
on each corner of the module base.
Make sure that the fan and retention mechanism assembly perfectly
fits the heatsink and module base, otherwise you cannot snap the
hooks into the holes.
Retention Hole
Retention Lock
Retention Hook Snapped
to the Retention Hole
Keep the retention locks lifted upward while fitting the retention
mechanism to the module base.
Chapter 2: Hardware information
3. Push down the locks on the retention mechanism to secure the
heatsink and fan to the module base.
When secure, the retention locks should point to opposite directions.
2.4.4 Connecting the CPU fan cable
When the fan, heatsink, and the retention mechanism are in place,
connect the CPU fan cable to the connector on the motherboard labeled
CPU Fan Connector
Don’t forget to connect the CPU fan connector! Hardware monitoring
errors may occur if you fail to plug this connector.
ASUS P4GE-V motherboard user guide
System memory
2.5.1 Overview
The motherboard comes with three Double Data Rate (DDR) Dual Inline
Memory Module (DIMM) sockets. These sockets support up to 2GB
system memory using 184-pin unbuffered non-ECC PC2700/PC2100/
80 Pins
104 Pins
P4GE-V 184-Pin DDR DIMM Sockets
This motherboard supports different memory frequencies depending on
the CPU FSB (Front Side Bus) and the type of DDR DIMM.
Memory Frequency
533 MHz
333 MHz
266 MHz
400 MHz
266 MHz
200 MHz
Notes on DDR technology
The DDR SDRAM technology evolved from the mainstream PC66, PC100,
PC133 memory known as Single Data Rate (SDR) SDRAM. DDR memory
however, has the ability to perform two data operations in one clock cycle,
thus providing twice the throughput of SDR memory.
A DDR DIMM has the same physical dimensions as an SDR DIMM, but it
has a 184-pin footprint compared to the 168-pin of the SDR DIMM. Also, a
DDR DIMM is single notched while an SDR DIMM is double notched.
Therefore, a DDR DIMM is not backward compatible with SDR, and should
be installed only in a socket specially designed for DDR DIMMs.
Chapter 2: Hardware information
2.5.2 Memory configurations
You may install any DDR DIMMs with 64MB, 128MB, 256MB, 512MB, and
1GB densities into the DIMM sockets.
Use only the following combinations to install DDR DIMMs. Otherwise,
the system may not boot up.
(Rows 0&1)
(Rows 2&3)
(Rows 3&2)
SS - Single-sided DIMM
DS - Double-sided DIMM
1. DDR DIMM sockets 2 and 3 share the same rows, so if you install
a double-sided DIMM into DIMM2 socket, you must leave DIMM3
socket empty.
2. You may install single-sided DIMMs into DIMM2 and DIMM3
sockets at the same time but neither one can be x16 DDR module.
3. Double-sided x16 DDR DIMMs are not supported on this
ASUS P4GE-V motherboard user guide
2.5.3 Installing a DIMM
Make sure to unplug the power supply before adding or removing
DIMMs or other system components. Failure to do so may cause
severe damage to both the motherboard and the components.
Follow these steps to install a DIMM.
DDR DIMM notch
1. Unlock a DIMM socket by
pressing the retaining clips
2. Align a DIMM on the socket such
that the notch on the DIMM
matches the break on the socket.
Unlocked Retaining Clip
A DDR DIMM is keyed with a notch so that it fits in only one direction.
DO NOT force a DIMM into a socket to avoid damaging the DIMM.
3. Firmly insert the DIMM into the
socket until the retaining clips
snap back in place and the DIMM
is properly seated.
Locked Retaining Clip
2.5.4 Removing a DIMM
Follow these steps to remove a DIMM.
1. Simultaneously press the
retaining clips outward to unlock
the DIMM.
Support the DIMM lightly with your fingers when pressing the retaining
clips. The DIMM might get damaged when it flips out with extra force.
2. Remove the DIMM from the socket.
Chapter 2: Hardware information
Expansion slots
In the future, you may need to install expansion cards. The motherboard
has six PCI slots and one Accelerated Graphics Port (AGP) slot. The
following sub-sections describe the slots and the expansion cards that
they support.
Make sure to unplug the power cord before adding or removing
expansion cards. Failure to do so may cause you physical injury and
damage motherboard components.
2.6.1 Installing an expansion card
Follow these steps to install an expansion card.
1. Before installing the expansion card, read the documentation that
came with it and make the necessary hardware settings for the card.
2. Remove the system unit cover (if your motherboard is already installed
in a chassis).
3. Remove the bracket opposite the slot that you intend to use. Keep the
screw for later use.
4. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
5. Secure the card to the chassis with the screw you removed earlier.
6. Replace the system cover.
2.6.2 Configuring an expansion card
After installing the expansion card, configure the it by adjusting the
software settings.
1. Turn on the system and change the necessary BIOS settings, if any.
See Chapter 4 for information on BIOS setup.
2. Assign an IRQ to the card. Refer to the tables on the next page.
3. Install the software drivers for the expansion card.
ASUS P4GE-V motherboard user guide
Standard Interrupt Assignments
Standard Function
System Timer
Keyboard Controller
Programmable Interrupt
Communications Port (COM2)
Communications Port (COM1)
Sound Card (sometimes LPT2)
Floppy Disk Controller
Printer Port (LPT1)
System CMOS/Real Time Clock
ACPI Mode when used
IRQ Holder for PCI Steering
IRQ Holder for PCI Steering
PS/2 Compatible Mouse Port
Numeric Data Processor
Primary IDE Channel
Secondary IDE Channel
These IRQs are usually available for ISA or PCI devices.
IRQ assignments for this motherboard
PCI slot 1
PCI slot 2
PCI slot 3
PCI slot 4
PCI slot 5
PCI slot 6
AGP slot
Onboard USB controller HC0 shared
Onboard USB controller HC1 —
Onboard USB controller HC2 —
Onboard USB 2.0 controller
Onboard LAN controller
— shared —
used —
— shared
— shared —
— shared —
shared —
shared —
— shared
— shared —
When using PCI cards on shared slots, ensure that the drivers support
“Share IRQ” or that the cards do not need IRQ assignments.
Otherwise, conflicts will arise between the two PCI groups, making the
system unstable and the card inoperable.
Chapter 2: Hardware information
2.6.3 PCI slots
There are six 32-bit PCI slots on this motherboard, including an ASUS
proprietary BlueMagic PCI slot. The slots support PCI cards such as a
LAN card, SCSI card, USB card, and other cards that comply with PCI
specifications. The following figure shows a LAN card installed on a PCI
2.6.4 AGP slot
This motherboard has an Accelerated Graphics Port (AGP) slot that
supports +1.5V AGP cards. When you buy an AGP card, make sure that
you ask for one with +1.5V specification. Note the notches on the card
golden fingers to ensure that they fit the AGP slot on your motherboard.
If you installed an incorrect AGP card, such as a SiS305-based AGP card
or any other 3.3V AGP card, the onboard red LED (AGP_WARN1) lights
up, an indication that the card is not supported on the motherboard. As
long as this LED is lighted, you cannot turn on the system power even if
you press the power button, thus preventing permanent damage to the
Install only 1.5V AGP cards on this motherboard!
P4GE-V Accelerated Graphics Port (AGP)
ASUS P4GE-V motherboard user guide
1. Keyboard power (3-pin KBPWR1)
This jumper allows you to enable or disable the keyboard wake-up
feature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up the
computer when you press a key on the keyboard (the default is the
Space Bar). This feature requires an ATX power supply that can supply
at least 1A on the +5VSB lead, and a corresponding setting in the
BIOS (see section 4.5.1 Power Up Control).
1 2
2 3
P4GE-V Keyboard Power Setting
2. Wireless PCI and USB settings (3-pin WPCI_USB)
These jumpers are reserved. DO NOT change the default settings.
3 1
5 3
4 2
6 4
reserved pin
Chapter 2: Hardware information
3. Clear RTC RAM (CLRTC1)
This jumper allows you to clear the Real Time Clock (RTC) RAM in
CMOS. You can clear the CMOS memory of date, time, and system
setup parameters by erasing the CMOS RTC RAM data. The RAM
data in CMOS, that include system setup information such as system
passwords, is powered by the onboard button cell battery.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the
cap on pins 2-3 for about 5~10 seconds, then move the cap back
to pins 1-2.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS
setup to re-enter data.
Except when clearing the RTC RAM, never remove the cap on
CLRTC1 jumper default position. Removing the cap will cause system
boot failure!
1 2
2 3
You do not need to clear the RTC when the system hangs due to
overclocking. For system failure due to overclocking, use the C.P.R.
(CPU Parameter Recall) feature. Shut down and reboot the system so
BIOS can automatically reset parameter settings to default values.
ASUS P4GE-V motherboard user guide
This section describes and illustrates the internal connectors on the
Always connect ribbon cables with the red stripe to Pin 1 on the
connectors. Pin 1 is usually on the side closest to the power connector
on hard drives and CD-ROM drives, but may be on the opposite side
on floppy disk drives.
1. Hard disk activity LED (2-pin IDE_LED1)
This connector supplies power to the hard disk activity LED. The read
or write activities of any device connected to the primary or secondary
IDE connector cause this LED to light up.
TIP: If the case-mounted LED does not
light up, try reversing the 2-pin plug.
P4GE-V HD Activity LED
2. Floppy disk drive connector (34-1 pin FLOPPY1)
This connector supports the provided floppy drive ribbon cable. After
connecting one end to the motherboard, connect the other end to the
floppy drive. (Pin 5 is removed to prevent incorrect insertion when
using ribbon cables with pin 5 plug).
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
P4GE-V Floppy Disk Drive Connector
Chapter 2: Hardware information
3. IDE connectors (40-1 pin IDE1, IDE2)
This connector supports the provided UltraDMA/100/66 IDE hard disk
ribbon cable. Connect the cable’s blue connector to the primary
(recommended) or secondary IDE connector, then connect the gray
connector to the UltraDMA/100/66 slave device (hard disk drive) and
the black connector to the UltraDMA/100/66 master device. It is
recommended that you connect non-UltraDMA/100/66 devices to the
secondary IDE connector. If you install two hard disks, you must
configure the second drive as a slave device by setting its jumper
accordingly. Refer to the hard disk documentation for the jumper
settings. BIOS supports specific device bootup. If you have more than
two UltraDMA/100/66 devices, purchase another UltraDMA/100/66
cable. You may configure two hard disks to be both master devices
with two ribbon cables – one for the primary IDE connector and
another for the secondary IDE connector.
1. Pin 20 on each IDE connector is removed to match the covered
hole on the UltraDMA cable connector. This prevents incorrect
orientation when you connect the cables.
2. The hole near the blue connector on the UltraDMA/100/66 cable is
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
P4GE-V IDE Connectors
For UltraDMA/100/66 IDE devices, use an 80-conductor IDE cable.
The UltraDMA/66 cable included in the motherboard package also
supports UltraDMA/100.
ASUS P4GE-V motherboard user guide
4. Chassis intrusion connector (4-1 pin CHASSIS1)
This lead is for a chassis designed with intrusion detection feature.
This requires an external detection mechanism such as a chassis
intrusion sensor or microswitch. When you remove any chassis
component, the sensor triggers and sends a high-level signal to this
lead to record a chassis intrusion event.
By default, the pins labeled “Chassis Signal” and “Ground” are shorted
with a jumper cap. If you wish to use the chassis intrusion detection
feature, remove the jumper cap from the pins.
Chassis Signal
P4GE-V Chassis Alarm Lead
5. SMBus connector (6-1 pin SMB1)
This connector allows you to connect SMBus (System Management
Bus) devices. Devices communicate with an SMBus host and/or other
SMBus devices using the SMBus interface.
P4GE-V SMBus Connector
Chapter 2: Hardware information
6. ASUS EZ Plug™ and ATX power connectors
(20-pin ATXPWR1, 4-pin EZ_PLUG1, 4-pin ATX12V1)
These connectors connect to an ATX 12V power supply. The plugs
from the power supply are designed to fit these connectors in only one
orientation. Find the proper orientation and push down firmly until the
connectors completely fit.
In addition to the 20-pin ATXPWR1 connector, this motherboard
requires that you connect the 4-pin ATX +12V power plug to provide
sufficient power to the CPU.
If you are using a standard ATX power supply that does not have the
ATX +12V plug, connect one 4-pin device power plug to the ASUS EZ
Plug™ connector labeled EZ_PLUG1.
Make sure that your ATX 12V power supply can provide 8A on the
+12V lead and at least 1A on the +5-volt standby lead (+5VSB). The
minimum recommended wattage is 230W, or 300W for a fully
configured system. The system may become unstable and may
experience difficulty powering up if the power supply is inadequate.
Pin 1
+12V DC
+12V DC
P4GE-V ATX & Auxiliary Power Connectors
ASUS P4GE-V motherboard user guide
7. CPU, Chassis, and Power Fan Connectors
(3-pin CPU_FAN1, PWR_FAN1, CHA_FAN1)
The fan connectors support cooling fans of 350mA~740mA (8.88W
max.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan
cables to the fan connectors on the motherboard, making sure that the
black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Lack of
sufficient air flow within the system may damage the motherboard
components. These are not jumpers! DO NOT place jumper caps on
the fan connectors!
P4GE-V 12-Volt Fan Connectors
8. Power supply thermal connector (2-pin TRPWR1)
If your power supply has a thermal monitoring feature, connect its
thermal sensor cable to this connector.
P4GE-V Power Supply Thermal Connector
Chapter 2: Hardware information
9. USB header (10-1 pin USB_56)
If the USB ports on the rear panel are inadequate, a USB header is
available for additional USB ports. The USB header complies with USB
2.0 specification that supports up to 480 Mbps connection speed. This
speed advantage over the conventional 12 Mbps on USB 1.1 allows
faster Internet connection, interactive gaming, and simultaneous
running of high-speed peripherals.
If your package came with a USB 2.0/GAME module, connect the USB
cable to this header. The module has two USB 2.0 ports that support
the next generation USB peripherals such as high resolution cameras,
scanners, and printers.
You must install the driver before you can use the USB 2.0 capability.
P4GE-V USB 2.0 Header
ASUS P4GE-V motherboard user guide
10. GAME/MIDI connector (16-1 pin GAME1)
This connector supports a GAME/MIDI module. If your package came
with the optional USB 2.0/GAME module, connect the GAME/MIDI
cable to this connector. The GAME/MIDI port on the module connects
a joystick or a game pad for playing games, and MIDI devices for
playing or editing audio files.
P4GE-V Game Connector
11. Internal audio connectors (4-pin CD1, AUX1, MODEM1)
(on audio models only)
These connectors allow you to receive stereo audio input from sound
sources such as a CD-ROM, TV tuner, or MPEG card. The MODEM
connector allows the onboard audio to interface with a voice modem
card with a similar connector. It also allows the sharing of mono_in
(such as a phone) and a mono_out (such as a speaker) between the
audio and a voice modem card.
CD1(Black) AUX1 (White)
Left Audio Channel
Right Audio Channel
P4GE-V Internal Audio Connectors
Chapter 2: Hardware information
12. Infrared module connector (5-1 pin IR1)
This connector supports an optional wireless transmitting and receiving
infrared module. This module mounts to a small opening on system
chassis that support this feature. You must also configure the UART2
Use As parameter in BIOS to set UART2 for use with IR. See section
“4.4.2 I/O Device Configuration” for details.
Use the five pins as shown in Back View and connect a ribbon cable
from the module to the motherboard SIR connector according to the
pin definitions.
Front View
Back View
P4GE-V Infrared Module Connector
13. Serial port 2 connector (10-1 pin COM2)
This connector accommodates a second serial port using an optional
serial port bracket. Connect the bracket cable to this connector then
install the bracket into a slot opening at the back of the system chassis.
P4GE-V Serial COM2 Bracket
ASUS P4GE-V motherboard user guide
14. Digital audio connector (4-1 pin SPDIF1) (on audio models only)
This connector is for the bundled S/PDIF audio module that allows
digital instead of analog sound output. Connect one end of the audio
cable to the S/PDIF Out connector on the motherboard, and the other
end to the S/PDIF module.
P4GE-V Digital Audio Connector
15. Front panel audio connector (10-1 pin FP_AUDIO1)
(on audio models only)
This is an interface for the Intel front panel audio cable that allow
convenient connection and control of audio devices.
Line out_R
Line out_L
P4GE-V Front Panel Audio Connector
Chapter 2: Hardware information
16. System panel connector (20-pin PANEL1)
This connector accommodates several system front panel functions.
+5 V
Power LED
Keyboard Lock
Reset SW
SMI Lead
P4GE-V System Panel Connectors
ATX Power
* Requires an ATX power supply.
• System Power LED Lead (3-1 pin PLED)
This 3-1 pin connector connects to the system power LED. The LED
lights up when you turn on the system power, and blinks when the
system is in sleep mode.
• Keyboard Lock Lead (2-pin KEYLOCK)
This 2-pin connector connects to a chassis-mounted switch to allow
the use of the keyboard lock feature.
• System Warning Speaker Lead (4-pin SPKR)
This 4-pin connector connects to the case-mounted speaker and
allows you to hear system beeps and warnings.
• System Management Interrupt Lead (2-pin SMI)
This 2-pin connector allows you to manually place the system into a
suspend mode, or “green” mode, where system activity is instantly
decreased to save power and to expand the life of certain system
components. Attach the case-mounted suspend switch to this 2-pin
• ATX Power Switch / Soft-Off Switch Lead (2-pin PWRBTN)
This connector connects a switch that controls the system power.
Pressing the power switch turns the system between ON and SLEEP,
or ON and SOFT OFF, depending on the BIOS or OS settings.
Pressing the power switch while in the ON mode for more than 4
seconds turns the system OFF.
• Reset Switch Lead (2-pin RESET)
This 2-pin connector connects to the case-mounted reset switch for
rebooting the system without turning off the system power.
ASUS P4GE-V motherboard user guide
Chapter 2: Hardware information
Chapter 3
This chapter describes the power up
sequence and gives information on the
BIOS beep codes.
Powering up
Chapter summary
Starting up for the first time .......................... 3-1
Vocal POST Messages ................................... 3-2
Powering off the computer ........................... 3-4
ASUS P4GE-V motherboard
Starting up for the first time
1. After making all the connections, replace the system case cover.
2. Be sure that all switches are off.
3. Connect the power cord to the power connector at the back of the system
4. Connect the power cord to a power outlet that is equipped with a surge
5. Turn on the devices in the following order:
a. Monitor
b. External SCSI devices (starting with the last device on the chain)
c. System power (if you are using an ATX power supply, you need to
switch on the power supply as well as press the ATX power switch on
the front of the chassis).
6. After applying power, the power LED on the system front panel case lights
up. For ATX power supplies, the system LED lights up when you press the
ATX power switch. If your monitor complies with “green” standards or if it
has a “power standby” feature, the monitor LED may light up or switch
between orange and green after the system LED turns on. The system
then runs the power-on tests. While the tests are running, the BIOS beeps
or additional messages appear on the screen. If you do not see anything
within 30 seconds from the time you turned on the power, the system may
have failed a power-on test. Check the jumper settings and connections or
call your retailer for assistance.
Award BIOS Beep Codes
One short beep when
displaying logo
No error during POST
Long beeps in an endless loop
No DRAM installed or detected
One long beep followed by
three short beeps
Video card not found or video card
memory bad
High frequency beeps when
system is working
CPU overheated;
System running at a lower frequency
You will not hear the BIOS beeps when the ASUS POST Reporter™ is
enabled. You will hear the vocal POST messages instead.
7. At power on, hold down <Delete> to enter BIOS Setup. Follow the
instructions in Chapter 4.
ASUS P4GE-V motherboard user guide
Vocal POST Messages
This motherboard includes the Winbond speech controller to support a
special feature called the ASUS POST Reporter™. This feature gives you
vocal POST messages and alerts to inform you of system events and boot
status. In case of a boot failure, you will hear the specific cause of the
These POST messages are customizable using the Winbond Voice Editor
software that came with your package. You can record your own
messages to replace the default messages.
Following is a list of the default POST messages and their corresponding
actions, if any.
POST Message
No CPU installed
• Install an Intel Pentium 4 Processor
into the CPU socket.
System failed CPU test
• Check the CPU if properly installed.
• Call ASUS technical support for
assistance. See the “ASUS contact
information” on page x.
System failed memory test
• Install 184-pin unbuffered
PC2700/2100/1600 DIMMs into the
DIMM sockets.
• Check if the DIMMs on the DIMM
sockets are properly installed.
• Make sure that your DIMMs are
not defective.
• Refer to section “2.5 System
memory” for instruction on installing
System failed VGA test
• Install a PCI VGA card into one of
the PCI slots, or a 1.5V AGP card
into the AGP slot.
• Make sure that your VGA/AGP card
is not defective.
System failed due to CPU
• In JumperFree mode, check your
CPU settings in BIOS and make
sure you only set to the recommended settings. See section “4.4
Advanced menu.”
Chapter 3: Powering up
POST Message
No keyboard detected
• Check your keyboard if properly
connected to the purple PS/2
connector on the rear panel.
• See section “1.4.1 Major
components” for the location of the
No floppy disk detected
• Make sure you have connected a
floppy disk to the floppy disk
connector on the motherboard.
• See section “2.8 Connectors.”
No IDE hard disk detected
• Make sure you have connected an
IDE hard disk drive to the one of the
IDE connectors on the motherboard.
• See section “2.8 Connectors.”
CPU temperature too high
• Check CPU fan if working properly.
CPU fan failed
• Check the CPU fan and make sure
it turns on after you applied power
to the system.
• Make sure that your CPU fan
supports the fan speed detection
CPU voltage out of range
• Check your power supply and
make sure it is not defective.
• Call ASUS technical support for
assistance. See the “ASUS contact
information” on page x.
System completed Power-On Self Test • No action required
Computer now booting from operating • No action required
You may disable the ASUS POST Reporter™ in the BIOS setup. See
section “4.4.2 I/O Device Configuration”.
ASUS P4GE-V motherboard user guide
Powering off the computer
You must first exit the operating system and shut down the system before
switching off the power. For ATX power supplies, you can press the ATX
power switch after exiting or shutting down the operating system. If you
use Windows 2000/XP, click the Start button, click Shut Down, then click
the OK button to shut down the computer. The power supply should turn
off after Windows shuts down.
The message “You can now safely turn off your computer” does not
appear when shutting down with ATX power supplies.
Chapter 3: Powering up
Chapter 4
This chapter tells how to change system
settings through the BIOS Setup menus.
Detailed descriptions of the BIOS
parameters are also provided.
BIOS setup
Chapter summary
Managing and updating your BIOS .............. 4-1
BIOS Setup program ...................................... 4-7
Main Menu .................................................... 4-10
Advanced Menu ........................................... 4-17
Power Menu .................................................. 4-29
Boot Menu .................................................... 4-35
Exit Menu ...................................................... 4-37
ASUS P4GE-V motherboard
Managing and updating your BIOS
It is recommended that you save a copy of the motherboard’s original
BIOS to a bootable floppy disk in case you need to reinstall the original
BIOS later.
4.1.1 Using ASUS EZ Flash to update the BIOS
The ASUS EZ Flash feature allows you to easily update the BIOS without
having to go through the long process of booting from a diskette and using
a DOS-based utility. The EZ Flash is built-in the BIOS firmware so it is
accessible by simply pressing <Alt> + <F2> during the Power-On Self
Tests (POST).
Follow these steps to update the BIOS using ASUS EZ Flash.
1. Download the latest BIOS file from the ASUS website (see ASUS
contact information on page x). Save the file to a floppy disk.
Write down the BIOS file name on a piece of paper. You need to type
the exact BIOS file name at the EZ Flash screen.
2. Reboot the computer.
3. To use EZ Flash, press <Alt> + <F2> during POST to display the
following screen.
ASUS EZ Flash V1.00
Copyright (C) 2002, ASUSTeK COMPUTER INC.
[Onboard BIOS Information]
BIOS Version
: ASUS P4GE-V ACPI BIOS Revision 1002
BIOS Model
: P4GE-V
BIOS Built Date : 04/16/02
Please Enter File Name for NEW BIOS: _
*Note: EZ Flash will copy file from A:\, Press [ESC] to reboot
The BIOS information in the above screen is for reference only. What
you see on your screen may not be exactly the same as shown.
4. Insert the disk that contains the new BIOS file into the floppy drive. You
will receive the error message, “WARNING! Device not ready.” if you
proceed to step 5 without the disk in the drive.
ASUS P4GE-V motherboard user guide
5. At the prompt, “Please Enter File Name for NEW BIOS: _”, type in the
BIOS file name that you downloaded from the ASUS website, then
press <Enter>.
EZ Flash will automatically access drive A to look for the file name that
you typed. When found, the following message appears on screen.
[BIOS Information in File]
BIOS Version: P4GE-V Boot Block
WARNING! Continue to update the BIOS (Y/N)? _
If you accidentally typed in a wrong BIOS file name, the error
message, “WARNING! File not found.” appears. Press <Enter> to
remove the message, then type in the correct file name. Press
6. At the above prompt, type Y to continue with the update process.
Pressing N exits the EZ Flash screen and reboots the system without
updating the BIOS.
The following prompts appear if you typed Y.
Flash Memory:
SST 49LF004
Update Main BIOS area
(Y/N)? _
7. Press Y to update the main BIOS area.
DO NOT shutdown or reset the system while updating the BIOS area!
Doing so may cause system boot failure.
8. When the update process is done, the message, “Press a key to
reboot” appears. Press any key to reboot the system with the new
Chapter 4: BIOS Setup
4.1.2 Using AFLASH to update the BIOS
Creating a bootable disk
AFLASH.EXE is a Flash Memory Writer utility that updates the BIOS by
uploading a new BIOS file to the programmable flash ROM on the
motherboard. This file works only in DOS mode. To determine the BIOS
version of your motherboard, check the last four numbers of the code
displayed on the upper left-hand corner of your screen during bootup.
Larger numbers represent a newer BIOS file.
1. Type FORMAT A:/S at the DOS prompt to create a bootable system
disk. DO NOT copy AUTOEXEC.BAT and CONFIG.SYS to the disk.
2. Type COPY D:\AFLASH\AFLASH.EXE A:\ (assuming D is your
CD-ROM drive) to copy AFLASH.EXE to the boot disk you created.
AFLASH works only in DOS mode. It does not work in the DOS prompt
within Windows, and does not work with certain memory drivers that
may be loaded when you boot from the hard drive. It is recommended
that you reboot using a floppy disk.
3. Reboot the computer from the floppy disk.
BIOS setup must specify “Floppy” as the first item in the boot
4. In DOS mode, type A:\AFLASH <Enter> to run AFLASH.
If the word “unknown” appears after Flash Memory:, the memory chip
is either not programmable or is not supported by the ACPI BIOS and
therefore, cannot be programmed by the Flash Memory Writer utility.
ASUS P4GE-V motherboard user guide
5. Select 1. Save Current BIOS to File from the Main menu and press
<Enter>. The Save Current BIOS To File screen appears.
6. Type a filename and the path, for example, A:\XXX-XX.XXX, then
press <Enter>.
Chapter 4: BIOS Setup
Updating the BIOS
Update the BIOS only if you have problems with the motherboard and
you are sure that the new BIOS revision will solve your problems.
Careless updating may result to more problems with the motherboard!
1. Download an updated ASUS BIOS file from the Internet (WWW or
FTP) (see ASUS CONTACT INFORMATION on page x for details) and
save to the boot floppy disk you created earlier.
2. Boot from the floppy disk.
3. At the “A:\” prompt, type AFLASH and then press <Enter>.
4. At the Main Menu, type 2 then press <Enter>. The Update BIOS
Including Boot Block and ESCD screen appears.
5. Type the filename of your new BIOS and the path, for example,
A:\XXX-XX.XXX, then press <Enter>.
To cancel this operation, press <Enter>.
6. When prompted to confirm the BIOS update, press Y to start the
ASUS P4GE-V motherboard user guide
7. The utility starts to program the new BIOS information into the Flash
ROM. The boot block is updated automatically only when necessary.
This minimizes the possibility of boot problems in case of update
failures. When the programming is done, the message “Flashed
Successfully” appears.
8. Follow the onscreen instructions to continue.
If you encounter problems while updating the new BIOS, DO NOT turn
off the system because this may cause boot problems. Just repeat the
process, and if the problem persists, load the original BIOS file you
saved to the boot disk. If the Flash Memory Writer utility is not able to
successfully update a complete BIOS file, the system may not boot. If
this happens, call the ASUS service center for support.
Chapter 4: BIOS Setup
BIOS Setup program
This motherboard supports a programmable Flash ROM that you can
update using the provided utility described in section “4.1 Managing and
updating your BIOS.”
Use the BIOS Setup program when you are installing a motherboard,
reconfiguring your system, or prompted to “Run Setup”. This section
explains how to configure your system using this utility.
Even if you are not prompted to use the Setup program, you may want to
change the configuration of your computer in the future. For example, you
may want to enable the security password feature or make changes to the
power management settings. This requires you to reconfigure your system
using the BIOS Setup program so that the computer can recognize these
changes and record them in the CMOS RAM of the Flash ROM.
The Flash ROM on the motherboard stores the Setup utility. When you
start up the computer, the system provides you with the opportunity to run
this program. Press <Delete> during the Power-On Self Test (POST) to
enter the Setup utility, otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing
<Ctrl> + <Alt> + <Delete>, or by pressing the reset button on the system
chassis. You can also restart by turning the system off and then back on.
Do this last option only if the first two failed.
The Setup program is designed to make it as easy to use as possible. It is
a menu-driven program, which means you can scroll through the various
sub-menus and make your selections among the predetermined choices.
Because the BIOS software is constantly being updated, the following
BIOS setup screens and descriptions are for reference purposes only,
and may not exactly match what you see on your screen.
ASUS P4GE-V motherboard user guide
4.2.1 BIOS menu bar
The top of the screen has a menu bar with the following selections:
Use this menu to make changes to the basic system
Use this menu to enable and make changes to the
advanced features.
Use this menu to configure and enable Power
Management features.
Use this menu to configure the default system device
used to locate and load the Operating System.
Use this menu to exit the current menu or to exit the
Setup program.
To access the menu bar items, press the right or left arrow key on the
keyboard until the desired item is highlighted.
4.2.2 Legend bar
At the bottom of the Setup screen is a legend bar. The keys in the legend
bar allow you to navigate through the various setup menus. The following
table lists the keys found in the legend bar with their corresponding
Navigation Key(s)
Function Description
<F1> or <Alt + H>
Displays the General Help screen from anywhere in the BIOS Setup
Jumps to the Exit menu or returns to the main
menu from a sub-menu
Left or Right arrow
Selects the menu item to the left or right
Up or Down arrow
Moves the highlight up or down between fields
- (minus key)
Scrolls backward through the values for the
highlighted field
+ (plus key) or spacebar Scrolls forward through the values for the highlighted field
Brings up a selection menu for the highlighted
<Home> or <PgUp>
Moves the cursor to the first field
<End> or <PgDn>
Moves the cursor to the last field
Resets the current screen to its Setup Defaults
Saves changes and exits Setup
Chapter 4: BIOS Setup
General help
In addition to the Item Specific Help window, the BIOS setup program also
provides a General Help screen. You may launch this screen from any
menu by simply pressing <F1> or the <Alt> + <H> combination. The
General Help screen lists the legend keys and their corresponding
Saving changes and exiting the Setup program
See “4.7 Exit Menu” for detailed information on saving changes and exiting
the setup program.
Scroll bar
When a scroll bar appears to the right of a help window, it indicates that
there is more information to be displayed that will not fit in the window. Use
<PgUp> and <PgDn> or the up and down arrow keys to scroll through the
entire help document. Press <Home> to display the first page, press
<End> to go to the last page. To exit the help window, press <Enter> or
Note that a right pointer symbol (as shown on the
left) appears to the left of certain fields. This pointer
indicates that you can display a sub-menu from this
field. A sub-menu contains additional options for a
field parameter. To display a sub-menu, move the
highlight to the field and press <Enter>. The submenu appears. Use the legend keys to enter values
and move from field to field within a sub-menu as
you would within a menu. Use the <Esc> key to
return to the main menu.
Take some time to familiarize yourself with the legend keys and their
corresponding functions. Practice navigating through the various menus
and sub-menus. If you accidentally make unwanted changes to any of the
fields, use the set default hot key <F5> to load the Setup default values.
While moving around through the Setup program, note that explanations
appear in the Item Specific Help window located to the right of each menu.
This window displays the help text for the currently highlighted field.
ASUS P4GE-V motherboard user guide
Main Menu
When you enter the Setup program, the following screen appears.
System Time [XX:XX:XX]
Sets the system to the time that you specify (usually the current time). The
format is hour, minute, second. Valid values for hour, minute and second
are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the <Tab>
or <Shift> + <Tab> keys to move between the hour, minute, and second
System Date [XX/XX/XXXX]
Sets the system to the date that you specify (usually the current date). The
format is month, day, year. Valid values for month, day, and year are
Month: (1 to 12), Day: (1 to 31), Year: (up to 2099). Use the <Tab> or
<Shift> + <Tab> keys to move between the month, day, and year fields.
Legacy Diskette A [1.44M, 3.5 in.]
Sets the type of floppy drive installed. Configuration options: [None] [360K,
5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.] [2.88M, 3.5 in.]
Floppy 3 Mode Support [Disabled]
This is required to support older Japanese floppy drives. The Floppy 3
Mode feature allows reading and writing of 1.2MB (as opposed to 1.44MB)
on a 3.5-inch diskette. Configuration options: [Disabled] [Enabled]
Chapter 4: BIOS Setup
Language [English US]
This field allows you to choose the BIOS language version from the
available options.
Supervisor Password [Disabled] / User Password [Disabled]
These fields allow you to set passwords. To set a password, highlight the
appropriate field and press <Enter>. Type in a password then press
<Enter>. You can type up to eight alphanumeric characters. Symbols and
other characters are ignored. To confirm the password, type the password
again and press <Enter>. The password is now set to [Enabled]. This
password allows full access to the BIOS Setup menus. To clear the
password, highlight this field and press <Enter>. The same dialog box as
above appears. Press <Enter>. The password is set to [Disabled].
A note about passwords
The BIOS Setup program allows you to specify passwords in the Main
menu. The passwords control access to the BIOS during system
startup. Passwords are not case sensitive, meaning, passwords typed
in either uppercase or lowercase letters are accepted. The BIOS Setup
program allows you to specify two different passwords: a Supervisor
password and a User password. If you did not set a Supervisor
password, anyone can access the BIOS Setup program. If you did, the
Supervisor password is required to enter the BIOS Setup program and
to gain full access to the configuration fields.
Forgot the password?
If you forget your password, you can clear it by erasing the CMOS
Real Time Clock (RTC) RAM. The RAM data containing the password
information is powered by the onboard button cell battery. See section
“2.7 Jumpers” for information on how to erase the RTC RAM.
Halt On [All Errors]
This field specifies the types of errors that will cause the system to halt.
Configuration options: [All Errors] [No Error] [All but Keyboard] [All but
Disk] [All but Disk/Keyboard]
Installed Memory [XXX MB]
This field automatically displays the amount of conventional memory
detected by the system during the boot process.
ASUS P4GE-V motherboard user guide
4.3.1 Primary and Secondary Master/Slave
Type [Auto]
Select [Auto] to automatically detect an IDE hard disk drive. If automatic
detection is successful, Setup automatically fills in the correct values for
the remaining fields on this sub-menu. If automatic detection fails, this may
be because the hard disk drive is too old or too new. If the hard disk was
already formatted on an older system, Setup may detect incorrect
parameters. In these cases, select [User Type HDD] to manually enter the
IDE hard disk drive parameters. Refer to the next section for details.
Before attempting to configure a hard disk drive, make sure you have
the correct configuration information supplied by the drive
manufacturer. Incorrect settings may cause the system to fail to
recognize the installed hard disk.
Chapter 4: BIOS Setup
[User Type HDD]
Manually enter the number of cylinders, heads and sectors per track for
the drive. Refer to the drive documentation or on the drive label for this
After entering the IDE hard disk drive information into BIOS, use a disk
utility, such as FDISK, to partition and format new IDE hard disk drives.
This is necessary so that you can write or read data from the hard disk.
Make sure to set the partition of the Primary IDE hard disk drives to
If no drive is installed or if you are removing a drive and not replacing it,
select [None].
Other options for the Type field are:
[CD-ROM] - for IDE CD-ROM drives
[LS-120] - for LS-120 compatible floppy disk drives
[ZIP] - for ZIP-compatible disk drives
[MO] - for IDE magneto optical disk drives
[Other ATAPI Device] - for IDE devices not listed here
After making your selections on this sub-menu, press the <Esc> key to
return to the Main menu. When the Main menu appears, the hard disk
drive field displays the size for the hard disk drive that you configured.
ASUS P4GE-V motherboard user guide
Translation Method [LBA]
Select the hard disk drive type in this field. When Logical Block Addressing
(LBA) is enabled, the 28-bit addressing of the hard drive is used without
regard for cylinders, heads, or sectors. Note that LBA Mode is necessary
for drives with more than 504MB storage capacity. Configuration options:
[LBA] [LARGE] [Normal] [Match Partition Table] [Manual]
This field configures the number of cylinders. Refer to the drive
documentation to determine the correct value. To make changes to this
field, set the Type field to [User Type HDD] and the Translation Method
field to [Manual].
This field configures the number of read/write heads. Refer to the drive
documentation to determine the correct value. To make changes to this
field, set the Type field to [User Type HDD] and the Translation Method
field to [Manual].
This field configures the number of sectors per track. Refer to the drive
documentation to determine the correct value. To make changes to this
field, set the Type field to [User Type HDD] and the Translation Method
field to [Manual].
CHS Capacity
This field shows the drive’s maximum CHS capacity as calculated by the
BIOS based on the drive information you entered.
Maximum LBA Capacity
This field shows the drive’s maximum LBA capacity as calculated by the
BIOS based on the drive information you entered.
Chapter 4: BIOS Setup
Multi-Sector Transfers [Maximum]
This option automatically sets the number of sectors per block to the
highest number that the drive supports. Note that when this field is
automatically configured, the set value may not always be the fastest
value for the drive. You may also manually configure this field. Refer to the
documentation that came with the hard drive to determine the optimum
value and set it manually. To make changes to this field, set the Type field
to [User Type HDD]. Configuration options: [Disabled] [2 Sectors] [4
Sectors] [8 Sectors] [16 Sectors] [32 Sectors] [Maximum]
SMART Monitoring [Disabled]
This field allows you to enable or disable the S.M.A.R.T. (Self-Monitoring,
Analysis and Reporting Technology) system that utilizes internal hard disk
drive monitoring technology. This parameter is normally disabled because
the resources used in the SMART monitoring feature may decrease
system performance. Configuration options: [Disabled] [Enabled]
PIO Mode [4]
This option lets you set a PIO (Programmed Input/Output) mode for the
IDE device. Modes 0 through 4 provide successive increase in
performance. Configuration options: [0] [1] [2] [3] [4]
Ultra DMA Mode [Disabled]
Ultra DMA capability allows improved transfer speeds and data integrity for
compatible IDE devices. Set to [Disabled] to suppress Ultra DMA
capability. To make changes to this field, set the Type field to [User Type
HDD]. Configuration options: [0] [1] [2] [3] [4] [5] [Disabled]
ASUS P4GE-V motherboard user guide
4.3.2 Keyboard Features
Boot Up NumLock Status [On]
This field enables users to activate the Number Lock function upon system
boot. Configuration options: [Off] [On]
Keyboard Auto-Repeat Rate [6/Sec]
This controls the speed at which the system registers repeated keystrokes.
Options range from 6 to 30 characters per second. Configuration options:
[6/Sec] [8/Sec] [10/Sec] [12/Sec] [15/Sec] [20/Sec] [24/Sec] [30/Sec]
Keyboard Auto-Repeat Delay [1/4 Sec]
This field sets the time interval for displaying the first and second
characters. Configuration options: [1/4 Sec] [1/2 Sec] [3/4 Sec] [1 Sec]
Chapter 4: BIOS Setup
Advanced Menu
CPU Speed [Manual]
When the motherboard is set to JumperFree™ mode, this field allows you
to select the internal frequency of the CPU. Select [Manual] if you want to
make changes to the two subsequent fields. Note that selecting a
frequency higher than the CPU manufacturer recommends may cause the
system to hang or crash.
CPU Frequency Multiple (when CPU Speed is set to [Manual])
This field sets the frequency multiple between the CPU’s internal
frequency (CPU speed) and external frequency. Set this field in
conjunction with CPU Frequency (MHz) to match the speed of the CPU.
The item CPU Frequency Multiple is accessible only if you have an
unlocked processor. If your processor frequency multiple is locked, you
cannot change the setting of this item.
CPU External Frequency (MHz) (when CPU Speed is set to [Manual])
This feature tells the clock generator what frequency to send to the system
bus and PCI bus. The bus frequency (external frequency) multiplied by the
bus multiple equals the CPU speed.
ASUS P4GE-V motherboard user guide
Memory Frequency [Auto]
This field determines whether the memory clock frequency is set to be in
synchronous or asynchronous mode with respect to the system frequency.
The options that appear in the popup menu vary according to the CPU
Frequency (MHz). Configuration options: [Auto] [266MHz] [355MHz]
AGP/PCI Frequency Setting [Auto]
When set to [Auto], this field allows automatic selection of AGP/PCI
frequency to enhance system performance and overclocking capability.
The setting [Manual] allows you to manually select the AGP/PCI
frequency. If the system becomes unstable, return to the default setting
[Auto]. When this item is set to [Manual], the AGP/PCI Frequency (MHz)
item appears. Configuration options: [Auto] [Manual]
AGP/PCI Frequency (MHz) [66.66/33.33]
This item appears only when the AGP/PCI Frequency Setting is set to
[Manual]. This field allows you to select a higher AGP/PCI frequency for
better system performance.
Selecting a very high AGP/PCI frequency may cause the system to be
CPU VCore Setting [Auto]
The [Manual] setting allows you to manually select the core voltage
supplied to the CPU (see next item). However, it is recommended that you
keep the default setting [Auto] to allow the system to automatically
determine the appropriate CPU core voltage.
Chapter 4: BIOS Setup
CPU VCore [1.500V]
When the CPU VCore Setting parameter above is set to [Manual], the
CPU VCore item allows you to select a specific CPU core voltage. This
field is not accessible when the CPU VCore Setting is set to [Auto].
Refer to the CPU documentation before setting this field. A very high
core voltage may severely damage the CPU!
DDR Reference Voltage [Auto]
This item controls the DDR SDRAM operating voltage. Configuration
options: [2.9V] [2.7V] [2.6V] [2.5V] [Auto]
AGP VDDQ Voltage [Auto]
This item controls the AGP operating voltage. Configuration options: [1.7V]
[1.6V] [1.5V] [Auto]
Hyper-Threading Technology [Enabled]
This item allows you to enable or disable the processor Hyper-Threading
Technology. Configuration options: [Disabled] [Enabled]
The item Hyper-Threading Technology appears only if you installed
an Intel Pentium 4 CPU that supports this feature.
CPU Level 1 Cache, CPU Level 2 Cache [Enabled]
These fields allow you to choose from the default [Enabled] or choose
[Disabled] to turn on or off the CPU Level 1 and Level 2 built-in cache.
Configuration options: [Disabled] [Enabled]
BIOS Update [Enabled]
This field functions as an update loader integrated into the BIOS to supply
the processor with the required data. When set to [Enabled], the BIOS
loads the update on all processors during system bootup. Configuration
options: [Disabled] [Enabled]
PS/2 Mouse Function Control [Auto]
The default setting [Auto] allows the system to detect a PS/2 mouse at
startup. If a mouse is detected, the BIOS assigns IRQ12 to the PS/2
mouse. Otherwise, IRQ12 can be used for expansion cards. When you set
this field to [Enabled], BIOS reserves IRQ12, whether or not a PS/2 mouse
is detected at startup. Configuration options: [Enabled] [Auto]
ASUS P4GE-V motherboard user guide
USB Legacy Support [Auto]
This motherboard supports Universal Serial Bus (USB) devices. The
default of [Auto] allows the system to detect a USB device at startup. If
detected, the USB controller legacy mode is enabled. If not detected, the
USB controller legacy mode is disabled.
When you set this field to [Disabled], the USB controller legacy mode is
disabled whether or not you are using a USB device. Configuration
options: [Disabled] [Enabled] [Auto]
OS/2 Onboard Memory > 64M [Disabled]
When using OS/2 operating systems with installed DRAM of greater than
64MB, you need to set this option to [Enabled]. Otherwise, leave to the
default setting [Disabled]. Configuration options: [Disabled] [Enabled]
4.4.1 Chip Configuration
SDRAM Configuration [By SPD]
This parameter allows you to set the optimal timings for items 2–5,
depending on the memory modules that you are using. The default setting
is [By SPD], which configures items 2–5 by reading the contents in the
SPD (Serial Presence Detect) device. The EEPROM on the memory
module stores critical information about the module, such as memory type,
size, speed, voltage interface, and module banks.
Configuration options: [User Defined] [By SPD]
Chapter 4: BIOS Setup
The SDRAM parameters (items 2~5) become configurable only when
you set the SDRAM Configuration to [User Defined].
SDRAM CAS Latency (value depends on SDRAM SPD)
This item controls the latency between the SDRAM read command and
the time the data actually becomes available. Configuration options: [2.5T]
[2T] [1.5T]
SDRAM RAS to CAS Delay (value depends on SDRAM SPD)
This item controls the latency between the DDR SDRAM active command
and the read/write command. Configuration options: [3T] [2T]
SDRAM RAS Precharge Delay (value depends on SDRAM SPD)
This item controls the idle clocks after issuing a precharge command to
the DDR SDRAM. Configuration options: [3T] [2T]
SDRAM Active Precharge Delay (value depends on SDRAM SPD)
This item controls the number of DDR SDRAM clocks used for DDR
SDRAM parameters. Configuration options: [8T] [7T] [6T] [5T]
System Performance Mode [Auto]
This item allows you to change the level of system performance.
Configuration options: [Auto] [Optimal] [Turbo]
SDRAM Idle Timer [Auto]
Configuration options: [Infinite] [0T] [8T] [16T] [64T] [Auto]
SDRAM Burst Length [Auto]
Configuration options: [Auto] [4] [8]
Memory Turbo Mode [Disabled]
This item allows you to enable or disable the memory turbo mode.
Configuration options: [Disabled] [Enabled]
DRAM Refresh Rate [By SPD]
Configuration options: [By SPD] [15.6us] [7.8us]
ASUS P4GE-V motherboard user guide
Onboard VGA [Auto]
When set to Auto, this item allows BIOS to automatically detect the
onboard VGA, and the AGP device if installed. Under this setting, the AGP
device has higher priority over the onboard VGA. If an AGP device is
present, the onboard VGA is disabled. If no AGP device is detected, the
onboard VGA is automatically enabled. When set to Enabled, the onboard
VGA is enabled. Any AGP device, even if present, is ignored.
Configuration options: [Auto] [Enabled]
If you set the Onboard VGA field to Enabled, the items Onboard VGA
Shared Memory, NTSC/PAL Preference, and Internal AGP Turbo Mode
appear. You may configure these items separately.
Onboard VGA Shared Memory [8 MB]
This item allows you to select the size of memory shared to the onboard
VGA. Configuration options: [1 MB] [8 MB]
NTSC/PAL Preference [NTSC]
This item allows you to select the TV output standard. Configuration
options: [NTSC] [PAL]
Internal AGP Turbo Mode [Disabled]
This item allows you to enable or disable the internal AGP turbo mode.
Configuration options: [Disabled] [Enabled]
Graphics Aperture Size [64MB]
This feature allows you to select the size of mapped memory for AGP
graphic data. Configuration options: [4MB] [8MB] [16MB] [32MB] [64MB]
[128MB] [256MB]
Chapter 4: BIOS Setup
AGP Capability [4X Mode]
This motherboard supports the AGP 4X interface that transfers video data
at 1066MB/s. AGP 4X is backward-compatible, so you may keep the
default [4X Mode] even if you are using an AGP 1X video card. When set
to [1X Mode], the AGP interface only provides a peak data throughput of
266MB/s even if you are using an AGP 4X card.
Configuration options: [1X Mode] [4X Mode]
Video Memory Cache Mode [UC]
USWC (uncacheable, speculative write combining) is a new cache
technology for the video memory of the processor. It can greatly improve
the display speed by caching the display data. You must set this to UC
(uncacheable) if your display card does not support this feature, otherwise
the system may not boot. Configuration options: [UC] [USWC]
The [USWC] options does not appear when using onboard VGA.
Memory Hole At 15M-16M [Disabled]
This field allows you to reserve an address space for ISA expansion cards.
Setting the address space to a particular setting makes that memory
space unavailable to other system components. Expansion cards can only
access memory up to 16MB. Configuration options: [Disabled] [Enabled]
Delayed Transaction [Enabled]
When set to [Enabled], this feature frees the PCI bus when the CPU is
accessing 8-bit ISA cards. This process normally consumes about 50-60
PCI clocks without PCI delayed transaction. Set this field to [Disabled]
when using ISA cards that are not PCI 2.1 compliant. Configuration
options: [Disabled] [Enabled]
Onboard PCI IDE [Both]
This field allows you to enable either the primary IDE channel or
secondary IDE channel, or both. You can also set both channels to
[Disabled]. Configuration options: [Both] [Primary] [Secondary] [Disabled]
USB 2.0 HS Reference Voltage [Medium]
This item controls the USB 2.0 high-speed drive strength reference
voltage. Configuration options: [Low] [Medium] [High] [Maximum]
ASUS P4GE-V motherboard user guide
4.4.2 I/O Device Configuration
Floppy Disk Access Control [R/W]
When set to [Read Only], this parameter protects files from being copied to
floppy disks by allowing reads from, but not writes to, the floppy disk drive.
The default setting [R/W] allows both reads and writes. Configuration
options: [R/W] [Read Only]
Onboard Serial Port 1 [3F8H/IRQ4]
Onboard Serial Port 2 [2F8H/IRQ3]
These fields allow you to set the addresses for the onboard serial
connectors. Serial Port 1 and Serial Port 2 must have different addresses.
Configuration options: [3F8H/IRQ4] [2F8H/IRQ3] [3E8H/IRQ4] [2E8H/
IRQ10] [Disabled]
UART2 Use As [COM Port]
This field allows you to select the device on which to assign UART2.
Configuration options: [COM Port] [IR]
Onboard Parallel Port [378H/IRQ7]
This field allows you to set the address of the onboard parallel port
connector. If you disable this field, the Parallel Port Mode and ECP DMA
Select configurations are not available. Configuration options: [Disabled]
[378H/IRQ7] [278H/IRQ5]
Chapter 4: BIOS Setup
Parallel Port Mode [ECP+EPP]
This field allows you to set the operation mode of the parallel port.
[Normal] allows normal-speed operation but in one direction only; [EPP]
allows bidirectional parallel port operation; [ECP] allows the parallel port to
operate in bidirectional DMA mode; [ECP+EPP] allows normal speed
operation in a two-way mode. Configuration options: [Normal] [EPP] [ECP]
ECP DMA Select [3]
This field allows you to configure the parallel port DMA channel for the
selected ECP mode. This selection is available only if you select [ECP] or
[ECP+EPP] in Parallel Port Mode above. Configuration options: [1] [3]
Onboard AC97 Audio Controller [Auto]
[Auto] allows the BIOS to detect whether you are using any audio device.
If an audio device is detected, the onboard audio controller is enabled; if
no audio device is detected, the controller is disabled. Configuration
options: [Disabled] [Auto]
Onboard Game Port [200H-207H]
This field sets the I/O address for the game port. Configuration options:
[Disabled] [200H-207H] [208H-20FH]
Onboard MIDI I/O [Disabled]
This field sets the I/O address for the MIDI I/O port. Configuration options:
[Disabled] [330H-331H] [300H-301H]
Speech POST Reporter [Enabled]
This field enables or disables the ASUS POST Reporter™ feature. See
section “1.3 Special Features” and “3.2 Vocal POST messages” for more
information. Configuration options: [Disabled] [Enabled]
ASUS P4GE-V motherboard user guide
4.4.3 PCI Configuration
Slot 1/5, Slot 2, Slot 3, Slot 4, Slot 6 IRQ [Auto]
These fields automatically assign the IRQ for each PCI slot. The default
setting for each field is [Auto], which utilizes auto-routing to determine IRQ
assignments. Configuration options: [Auto] [NA] [3] [4] [5] [7] [9] [10] [11]
[12] [14] [15]
PCI/VGA Palette Snoop [Disabled]
Some non-standard VGA cards, like graphics accelerators or MPEG video
cards, may not show colors properly. Setting this field to [Enabled] corrects
this problem. If you are using standard VGA cards, leave this field to the
default setting [Disabled]. Configuration options: [Disabled] [Enabled]
PCI Latency Timer [32]
Leave this field to the default setting [32] for best performance and
USB 1.1 Controllers [3 Controllers]
This field allows you to select the number of USB 1.1 controllers that you
wish to activate. Configuration options: [Disabled] [3 Controllers]
Chapter 4: BIOS Setup
USB 2.0 Controller [Enabled]
This field allows you to enable or disable the onboard USB 2.0 controller.
Set to [Enabled] if you wish to install USB 2.0 devices. Configuration
options: [Disabled] [Enabled]
Primary VGA BIOS [PCI VGA Card]
This field allows you to select the primary graphics card. Configuration
options: [PCI VGA Card] [AGP VGA Card] [Onboard VGA]
The option [Onboard VGA] appears only when the onboard VGA is
either used or enabled.
Onboard LAN Controller [Enabled]
This field allows you to enable or disable the onboard LAN controller.
Configuration options: [Disabled] [Enabled]
Onboard LAN Boot ROM [Disabled]
This field allows you to enable or disable the option ROM in the onboard
LAN controller chipset. Configuration options: [Disabled] [Enabled]
ASUS P4GE-V motherboard user guide
4-27 PCI IRQ Resource Exclusion
IRQ XX Reserved [No/ICU]
These fields indicate whether or not the displayed IRQ for each field is
being used by a legacy (non-PnP) ISA card. The setting [No/ICU] for an
IRQ field indicates that you are using the ISA Configuration Utility (ICU),
and that this particular IRQ is NOT required by a legacy ISA card. Set the
IRQ field to [Yes] if you install a legacy ISA card that requires a unique IRQ
and you are NOT using ICU. Configuration options: [No/ICU] [Yes]
Chapter 4: BIOS Setup
Power Menu
The Power menu allows you to reduce power consumption. This feature
turns off the video display and shuts down the hard disk after a period of
Power Management [User Defined]
This field allows you to activate or deactivate the automatic power saving
features. When set to [Disabled], the power management features do not
function regardless of the other settings on this menu. The [User Defined]
option allows you to set the period of inactivity before the system enters
suspend mode. Refer to “Suspend Mode” item.
When set to [Max Saving], system power is conserved to its greatest
amount. This setting automatically puts the system into suspend mode
after a brief period of system inactivity. [Min Saving] allows the least power
saving as the system enters suspend mode only after a long period of
inactivity. Configuration options: [User Defined] [Disabled] [Min Saving]
[Max Saving]
You should install the Advanced Power Management (APM) utility to
keep the system time updated even when the computer enters
suspend mode. In Windows 3.x and Windows 95, you need to install
Windows with the APM feature. In Windows 98 or later, APM is
automatically installed as indicated by a battery and power cord icon
labeled “Power Management” in the Control Panel. Select the item
“Advanced” in the Power Management Properties dialog box.
ASUS P4GE-V motherboard user guide
Video Off Option [Suspend -> Off ]
This field determines when to activate the video off feature for monitor
power management. Configuration options: [Always On] [Suspend -> Off]
Video Off Method [DPMS OFF]
This field defines the video off features. The Display Power Management
System (DPMS) feature allows the BIOS to control the video display card if
it supports the DPMS feature. [Blank Screen] only blanks the screen. Use
this for monitors without power management or “green” features.
Even if installed, your screen saver does not display when you select
[Blank Screen] for the above field.
[V/H SYNC+Blank] blanks the screen and turns off vertical and horizontal
scanning. Configuration options: [Blank Screen] [V/H SYNC+Blank]
[DPMS Standby] [DPMS Suspend] [DPMS OFF] [DPMS Reduce ON]
HDD Power Down [Disabled]
Shuts down any IDE hard disk drives in the system after a period of
inactivity as set in this user-configurable field. This feature does not affect
SCSI hard drives. Configuration options: [Disabled] [1 Min] [2 Min] [3
Min]...[15 Min]
ACPI Suspend To RAM [Disabled]
This field allows you to enable or disable the ACPI Suspend-to-RAM
feature. To support this feature, the +5VSB of the power supply should
have the capacity to provide more than 720mA current. Configuration
options: [Disabled] [Enabled]
Suspend Mode [Disabled]
Sets the time period before the system goes into suspend mode.
Configuration options: [Disabled] [1~2 Min] [2~3 Min] [4~5 min] [8~9 Min]
[20 Min] [30 Min] [40 Min] [1 hour]
PWR Button < 4 Secs [Soft Off]
When set to [Soft off], the ATX switch can be used as a normal system
power-off button when pressed for less than 4 seconds. [Suspend] allows
the button to have a dual function where pressing less than 4 seconds
puts the system in sleep mode. Regardless of the setting, holding the ATX
switch for more than 4 seconds powers off the system. Configuration
options: [Soft off] [Suspend]
Chapter 4: BIOS Setup
4.5.1 Power Up Control
AC PWR Loss Restart [Disabled]
This allows you to set whether or not to reboot the system after power
interruptions. [Disabled] leaves your system off while [Enabled] reboots the
system. [Previous State] sets the system back to the state it was before
the power interruption. Configuration options: [Disabled] [Enabled]
[Previous State]
Wake/Power Up On Ext. Modem [Disabled]
This allows either settings of [Enabled] or [Disabled] for powering up the
computer when the external modem receives a call while the computer is
in Soft-off mode. Configuration options: [Disabled] [Enabled]
The computer cannot receive or transmit data until the computer and
applications are fully running. Thus, connection cannot be made on the
first try. Turning an external modem off and then back on while the
computer is off causes an initialization string that turns the system
power on.
Power Up On PCI Card [Disabled]
When set to [Enabled], this parameter allows you to turn on the system
through a PCI LAN or modem card. This feature requires an ATX power
supply that provides at least 1A on the +5VSB lead.
Configuration options: [Disabled] [Enabled]
ASUS P4GE-V motherboard user guide
Power On By PS/2 Keyboard [Space Bar]
This parameter allows you to use specific keys on the keyboard to turn on
the system. This feature requires an ATX power supply that provides at
least 1A on the +5VSB lead. Configuration options: [Disabled] [Space Bar]
[Ctrl-Esc] [Power Key]
Power On By PS/2 Mouse [Disabled]
When set to [Enabled], this parameter allows you to use the PS/2 mouse
to turn on the system. This feature requires an ATX power supply that
provides at least 1A on the +5VSB lead. Configuration options: [Disabled]
Automatic Power Up [Disabled]
This allows an unattended or automatic system power up. You may
configure your system to power up at a certain time of the day by selecting
[Everyday] or at a certain time and day by selecting [By Date].
Configuration options: [Disabled] [Everyday] [By Date]
Chapter 4: BIOS Setup
4.5.2 Hardware Monitor
MB Temperature [xxxC/xxxF]
CPU Temperature [xxxC/xxxF]
POWER Temperature [Ignore]
The onboard hardware monitor automatically detects and displays the
motherboard and CPU temperatures.
If your power supply comes with a two-pin thermal sensor cable, connect
this cable to the TRPWR connector on the motherboard to allow BIOS to
auto-detect the power supply temperature (see page 2-22 for the location
of the TRPWR connector). The POWER temperature item shows the
detected value if you have the appropriate power supply. Select [Ignore] to
disable the power temperature auto-detect function.
Q-Fan Control [Disabled]
This item allows you to enable or disable the ASUS Q-Fan feature that
smartly adjusts the fan speeds for more efficient system operation. When
this field is set to [Enabled], the Fan Speed Ratio and Speed Up/Down
Response Time items appear to allow selection of the appropriate fan
speeds and the corresponding response time. Configuration options:
[Disabled] [Enabled]
ASUS P4GE-V motherboard user guide
Fan Speed Ratio [10/15]
This item allows you to select the appropriate fan speed ratio for the
system. The default [10/15] is the minimum fan speed ratio. Select a
higher ratio if you installed additional devices and the system requires
more ventilation. This item appears only when the Q-Fan Control item is
set to [Enabled]. Configuration options: [10/15] [11/15] [12/15] [13/15]
[14/15] [Full Speed]
Speed Up/Down Response Time [4 Sec/8 Sec]
This item indicates the time period before the fan speeds adjust to the
value set in the Fan Speed Ratio field. This item appears only when the
Q-Fan Control item is set to [Enabled]. Configuration options:
[1 Sec/2 Sec] [2 Sec/4 Sec] [3 Sec/6 Sec] [4 Sec/8 Sec]
CPU Fan Speed [xxxxRPM] or [N/A]
Chassis Fan Speed [xxxxRPM] or [N/A]
Power Fan Speed [xxxxRPM] or [N/A]
The onboard hardware monitor automatically detects and displays the
CPU, chassis, and power fan speeds in rotations per minute (RPM). If any
of the fans is not connected to the motherboard, the specific field shows
VCORE Voltage, +3.3V Voltage, +5V Voltage, +12V Voltage
The onboard hardware monitor automatically detects the voltage output
through the onboard voltage regulators.
If any of the monitored items is out of range, the following error
message appears: “Hardware Monitor found an error. Enter Power
setup menu for details”. You will then be prompted to “Press F1 to
continue or DEL to enter SETUP”.
Chapter 4: BIOS Setup
Boot Menu
Boot Sequence
The Boot menu allows you to select among the four possible types of boot
devices listed using the up and down arrow keys. By using the <+> or
<Space> key, you can promote devices and by using the <-> key, you can
demote devices. Promotion or demotion of devices alters the priority which
the system uses to search for a boot device on system power up.
Configuration fields include Removable Devices, IDE Hard Drive, ATAPI
CD-ROM, and Other Boot Device.
Removable Device [Legacy Floppy]
Configuration options: [Disabled] [Legacy Floppy] [LS-120] [ZIP]
IDE Hard Drive
This field allows you to select which IDE hard disk drive to use in the boot
sequence. Pressing [Enter] will show the product IDs of all connected IDE
hard disk drives.
This field allows you to select which ATAPI CD-ROM drive to use in the
boot sequence. Pressing [Enter] will show the product IDs of all your
connected ATAPI CD-ROM drives.
Other Boot Device Select [INT18 Device (Network)]
Configuration options: [Disabled] [SCSI Boot Device] [INT18 Device
ASUS P4GE-V motherboard user guide
Plug & Play O/S [No]
This field allows you to use a Plug-and-Play (PnP) operating system to
configure the PCI bus slots instead of using the BIOS. When [Yes] is
selected, interrupts may be reassigned by the OS. If you installed a nonPnP OS or if you want to prevent reassigning of interrupt settings, keep
the default setting [No]. Configuration options: [No] [Yes]
Reset Configuration Data [No]
The Extended System Configuration Data (ESCD) contain information
about non-PnP devices. It also holds the complete record of how the
system was configured the last time it was booted. Select [Yes] if you want
to clear these data during the Power-On-Self-Test (POST).
Configuration options: [No] [Yes]
Boot Virus Detection [Enabled]
This field allows you to set boot virus detection, ensuring a virus-free boot
sector. The system halts and displays a warning message when it detects
a virus. If this occurs, you can either allow the operation to continue or use
a virus-free bootable floppy disk to restart and investigate your system.
Configuration options: [Disabled] [Enabled]
Quick Power On Self Test [Enabled]
This field speeds up the Power-On-Self Test (POST) routine by skipping
retesting a second, third, and fourth time. Configuration options: [Disabled]
Boot Up Floppy Seek [Enabled]
When enabled, the BIOS will seek the floppy disk drive to determine
whether the drive has 40 or 80 tracks. Configuration options: [Disabled]
Full Screen Logo [Enabled]
This allows you to enable or disable the full screen logo display feature.
Configuration options: [Disabled] [Enabled]
Make sure that the above item is set to [Enabled] if you wish to use the
ASUS MyLogo2™ feature.
Interrupt Mode [APIC]
The Advanced Programmable Interrupt Controller (APIC) setting allows
you to distribute interrupt routings other than the 16 IRQs. The
Programmable Interrupt Controller (PIC) setting allows you to use the 16
IRQs only. Configuration options: [PIC] [APIC]
Chapter 4: BIOS Setup
Exit Menu
When you have made all of your selections from the various menus in the
Setup program, save your changes and exit Setup. Select Exit from the
menu bar to display the following menu.
Pressing <Esc> does not immediately exit this menu. Select one of the
options from this menu or <F10> from the legend bar to exit.
Exit Saving Changes
Once you are finished making your selections, choose this option from the
Exit menu to ensure the values you selected are saved to the CMOS RAM.
The CMOS RAM is sustained by an onboard backup battery and stays on
even when the PC is turned off. When you select this option, a
confirmation window appears. Select [Yes] to save changes and exit.
If you attempt to exit the Setup program without saving your changes,
the program prompts you with a message asking if you want to save
your changes before exiting. Pressing <Enter> saves the changes
while exiting.
Exit Discarding Changes
Select this option only if you do not want to save the changes that you
made to the Setup program. If you made changes to fields other than
system date, system time, and password, the BIOS asks for a confirmation
before exiting.
ASUS P4GE-V motherboard user guide
Load Setup Defaults
This option allows you to load the default values for each of the
parameters on the Setup menus. When you select this option or if you
press <F5>, a confirmation window appears. Select [Yes] to load default
values. Select Exit Saving Changes or make other changes before saving
the values to the non-volatile RAM.
Discard Changes
This option allows you to discard the selections you made and restore the
previously saved values. After selecting this option, a confirmation
appears. Select [Yes] to discard any changes and load the previously
saved values.
Save Changes
This option saves your selections without exiting the Setup program. You
can then return to other menus and make further changes. After you select
this option, a confirmation window appears. Select [Yes] to save any
changes to the non-volatile RAM.
Chapter 4: BIOS Setup
Chapter 5
This chapter describes the contents of the
support CD that comes with the
motherboard package.
Software support
Chapter summary
Install an operating system ........................... 5-1
Support CD information ................................ 5-1
Software information ..................................... 5-9
ASUS P4GE-V motherboard
Install an operating system
This motherboard supports Windows 98/ME/NT/2000/XP operating system
(OS). Always install the latest OS version and corresponding updates so
you can maximize the features of your hardware.
Because motherboard settings and hardware options vary, use the
setup procedures presented in this chapter for general reference only.
Refer to your OS documentation for more information.
Support CD information
The support CD that came with the motherboard contains useful software
and several utility drivers that enhance the motherboard features.
The contents of the support CD are subject to change at any time
without notice. Visit the ASUS website for updates.
5.2.1 Running the support CD
To begin using the support CD, simply insert the CD into your CD-ROM
drive. The CD automatically displays the Drivers menu if Autorun is
enabled in your computer.
Click an item to install
Click an icon to display
more information
If Autorun is NOT enabled in your computer, browse the contents of
the support CD to locate the file ASSETUP.EXE from the BIN folder.
Double-click the ASSETUP.EXE to run the CD.
ASUS P4GE-V motherboard user guide
5.2.2 Drivers menu
The drivers menu shows the available device drivers if the system detects
installed devices. Install the necessary drivers to activate the devices.
Intel Chipset Inf Update program
This item installs the Intel® Chipset INF Update Program that enables
Plug-n-Play INF support for Intel chipset components. This utility installs to
the target system the Windows INF files that outline to the operating
system how the chipset components will be configured.
You may install this utility in three modes: interactive, silent, and
unattended preload. The interactive mode requires user input during
installation. This is not required in the silent and unattended preload
Refer to the online help or readme file that came with the utility.
Intel Application Accelerator Driver
This item installs the Intel Application Accelerator for Microsoft® Windows®
98/98SE/ME/NT4.0/2000. This program is designed to improve
performance of the storage sub-system and overall system performace.
Install the INF Driver before installing the Intel Application Accelerator.
Chapter 5: Software support
SoundMAX Audio Driver and Application
This item installs the AC’ 97 SoundMAX audio driver and application to
activate the 6-channel audio features.
BroadCom 4401 LAN Driver
This item installs the BroadCom® BCM4401 driver to support 10BASE-T/
100BASE-TX networking.
Important note on BCM4401 LAN controller
If you installed the BCM4401 controller drivers, the default setting, Wake
Up Frame, allows system wake-up from S1, S3, and S4 sleep modes. If
you wish to wake-up the system from S5 mode (shut down mode), you
must manually change the Wake-On-LAN settings to Magic Frame.
To adjust Wake-On-LAN settings:
1. Right-click My Computer icon on your desktop,
and select Properties to display the System
Properties window.
2. On the System Properties
window, click on the Hardware
tab. Click on the Device
Manager button to display the
Device Manager window.
ASUS P4GE-V motherboard user guide
3. On the Device Manager window,
click the plus sign (+) opposite the
Network adapters item to show
the ASUSTeK/BroadCom 440x
10/100 Integrated Controller.
Double-click the item.
4. On the window that appears, click
the item Wake Up Capabilities
under Property. The default value
is Wake Up Frame.
The Wake Up Frame setting
wakes up the system from S1,
S3, and S4 sleep modes.
5. Click the arrow under Value to set
to Magic Frame. Click OK.
The Magic Frame setting wakes
up the system from S1, S3, S4
and S5 sleep modes.
If the BCM4401 LAN controller is onboard, the Wake-On-LAN feature
does NOT work on DOS mode.
Chapter 5: Software support
5.2.3 Utilities menu
The Utilities menu shows the applications and other software that the
motherboard supports.
ASUS PC Probe V2.18.00
This smart utility monitors the fan speed, CPU temperature, and system
voltages, and alerts you on any detected problems. This utility helps you
keep your computer at a healthy operating condition.
Install ASUS Update V3.32.01
This program allows you to download the latest version of the BIOS from
the ASUS website.
Before using the ASUS Update, make sure that you have an Internet
connection so you can connect to the ASUS website.
Microsoft Direct X 8.1 Driver
This item installs the Microsoft V8.0a driver.
This item installs the PC-cillin 2002 anti-virus program. View the PC-cillin
online help for detailed information.
Adobe Acrobat Reader V5.0
This item installs the Adobe Acrobat Reader V5.0. The Acrobat Reader
software is for viewing files saved in Portable Document Format (PDF).
ASUS P4GE-V motherboard user guide
Winbond Voice Editor
This program is for recording and customizing wave files for the ASUS
POST Reporter™. Use this program if you wish to change the default
vocal POST messages. See section “3.2 Vocal POST messages” for a list
of the default messages.
ASUS Screen Saver
This item installs the ASUS screen saver.
E-Color 3Deep
This item installs the 3Deep software. 3Deep is the first application that
gives online gamers the competitive edge in multi-player skirmishes. This
application removes dark washed-out graphics to deliver true vibrant
5.2.4 ASUS Contact Information
Clicking the ASUS Contact Information tab displays as stated. You may
also find this information on page x of this user guide.
Chapter 5: Software support
5.2.5 Other information
The icons on the top right corner of the screen give additional information
on the motherboard and the contents of the support CD. Click an icon to
display the specified information.
Motherboard Info
The window displays the general specifications of the P4GE-V
Browse this CD
The window displays the support CD contents in graphical format.
ASUS P4GE-V motherboard user guide
Technical Support Form
The window displays the ASUS Technical Support Request Form that you
have to fill up when requesting technical support.
The window displays the contents of the support CD and a brief
description of each in text format.
Chapter 5: Software support
Software information
Most of the applications in the support CD have wizards that will
conveniently guide you through the installation. View the online help or
readme file that came with the software for more information.
This section provides details on the software applications that the
motherboard supports.
5.3.1 ASUS Update
The ASUS Update is a utility that allows you to update the motherboard
BIOS and drivers. This utility requires an Internet connection either
through a network or an Internet Service Provider (ISP).
Follow these steps to use the ASUS Update.
1. Launch the utility from your Windows
Start menu:
Programs/AsusUpdate Vx.xx.xx/
The ASUS Update initial screen
2. Select your desired update method,
then click Next.
3. If you selected updating/
downloading from the Internet,
select the ASUS FTP site nearest
you to avoid network traffic, or
choose Auto Select. Click Next.
ASUS P4GE-V motherboard user guide
4. From the FTP site, select the
BIOS version that you wish to
download. Click Next.
5. Follow the instructions on the
succeeding screens to complete
the update process.
If you selected the option to update
the BIOS from a file, a window pops
up prompting you to locate the file.
Select the file, click Save, then follow
the screen instructions to complete
the update process.
5.3.2 ASUS MyLogo2™
The ASUS MyLogo2™ is automatically installed when you install the
ASUS Update utility from the software menu. See section “5.2.3 Software
Before using ASUS MyLogo2 feature, use the AFLASH utility to make
a copy of your original BIOS file, or obtain the latest BIOS version from
the ASUS website.
Make sure that the BIOS item Full Screen Logo is set to [Enabled] is
you wish to use ASUS MyLogo2. See page 4-35.
Follow these steps to use ASUS MyLogo2.
1. Launch the ASUS Update utility.
See section “5.3.1 ASUS Update.”
2. When prompted for the BIOS
update method, select the option
“Update BIOS from a file.”
3. Specify the location of the BIOS
file, such as from a floppy disk.
Click Next.
Chapter 5: Software support
4. From the selection that appears,
choose a logo image. Click Next.
If you wish, you may create
your own boot logo image in
GIF, JPG, or BMP file formats.
5. When you click on an image, it
displays larger on the MyLogo2
MyLogo2 may not support too complex images. If you encounter any
problems on complex images, try using a simpler image. You may also
use a photo editing software to shink the complex image, lay it over a
one-color 640x480 pixel background, and save the image with the
background. When you use the image, it will appear smaller and
centered on the screen.
6. The next screen prompts you to
flash the original BIOS to update
it with the new boot logo. Click
Flash to update the BIOS.
7. When finished, click Exit, then
reboot your computer.
Your system boots with the new
boot logo.
Instead of starting from ASUS Update, you may also launch ASUS
MyLogo2 directly from the Windows Start menu to change your BIOS
boot logo. After you have modified the BIOS file with the new logo, use
the ASUS Update utility to upload the new BIOS.
ASUS P4GE-V motherboard user guide
5.3.3 ASUS PC Probe
The ASUS PC Probe is a convenient utility to continuously monitor your
computer system’s vital components, such as fan rotations, voltages, and
temperatures. It also has a utility that lets you review useful information
about your computer, such as hard disk space, memory usage, and CPU
type, CPU speed, and internal/external frequencies through the DMI
Starting ASUS PC Probe
When ASUS PC Probe starts, a splash screen appears allowing you to
select whether to show the screen again when you open PC Probe or not.
To bypass this startup screen, clear the Show up in next execution check
To launch ASUS PC Probe, click the Windows Start button, point to
Programs, and then ASUS Utility, and then click Probe Vx.xx.
appears on the taskbar system tray indicating
The PC Probe icon
that ASUS PC Probe is running. Clicking the icon allows you to see the
status of your PC.
Chapter 5: Software support
Using ASUS PC Probe
Monitor Summary
Shows a summary of the items
being monitored.
Temperature Monitor
Shows the PC temperature (for
supported processors only).
Temperature Warning
threshold adjustment
(Move the slider up to increase the
threshold level or down to decrease
the threshold level)
Fan Monitor
Shows the PC fan rotation.
Fan Warning
threshold adjustment
(Move the slider up to increase the
threshold level or down to decrease
the threshold level)
Voltage Monitor
Shows the PC voltages.
ASUS P4GE-V motherboard user guide
Lets you set threshold levels and
polling intervals or refresh times of
the PC’s temperature, fan rotation,
and voltages.
CPU Cooling System Setup
Lets you select when to enable software CPU
cooling. When When CPU Overheated is selected,
the CPU cooling system is enabled whenever the
CPU temperature reaches the threshold value.
Lets you record the monitoring
activity of a certain component of
your PC for future reference.
Fan Control
Lets you enable/disable Smart Fan
Control. Smart Fan Control adjusts
the fan speed automatically based
on the current CPU temperature
and predefined threshold.
Hard Drives
Shows the used and free space of
the PC’s hard disk drives and the
file allocation table or file system
Chapter 5: Software support
Shows the PC memory load,
memory usage, and paging file
Device Summary
Shows a summary of devices
present in your PC.
DMI Explorer
Shows information pertinent to the
PC, such as CPU type, CPU
speed, and internal/external
frequencies, and memory size.
Lets you run programs outside of
the ASUS Probe modules. To run a
program, click Execute Program.
NOTE: This feature is currently
ASUS P4GE-V motherboard user guide
ASUS PC Probe Task Bar Icon
Right clicking the PC Probe
icon brings up a menu to
open or exit ASUS PC Probe
and pause or resume all
system monitoring.
When the ASUS PC Probe
senses a problem with your PC,
portions of the ASUS PC Probe
icon change to red, the PC
speaker beeps, and the ASUS
PC Probe monitor appears.
Chapter 5: Software support
5.3.4 Winbond Voice Editor
The Winbond Voice Editor software allows you to customize the vocal
POST messages. Install the software from the software menu in the
support CD. See section “5.2.3 Software menu”.
To avoid conflicts, do not run the Winbond Voice Editor while running
the ASUS PC Probe.
Follow these steps to use the Winbond Voice Editor.
Launching the program
Launch the program either from the Winbond Voice Editor icon on your
desktop, or from the Windows Start menu, Programs/Winbond Voice Editor/
Voice Editor.
The Winbond Voice Editor screen appears.
Default Messages
POST Events
Playing the default wave files
To play the default wave files, simply click on a POST event on the left
side of the screen, then click the Play button.
The default language setting is English.
ASUS P4GE-V motherboard user guide
Changing the default language
1. Click on the Load button. a
window showing the available
languages appears.
2. Select your desired language then
click Open. The event messages
for the language you selected
appear on the Voice Editor screen.
For some languages, not all events have a corresponding message
due to file size constraints.
3. Click on the Write button to update
4. Click Yes on the confirmation
window that appears.
The next time you boot your computer, the POST messages are
announced in the language that you selected .
Chapter 5: Software support
Customizing your POST messages
If your language is not in the selection or if you wish to record your own
POST messages to replace the pre-installed wave files, you may easily do
Follow these steps to customize your POST messages.
1. Launch the Voice Editor and take note of the list of POST events on
the leftmost column of the screen.
2. Prepare your message for each event.
The total compressed size for all the wave files must not exceed 1Mbit,
so make your messages as short as possible.
3. Use a recording software, such as Windows Recorder, to record your
4. Save the messages as wave files (.WAV). It is recommended that you
save your files in low quality to keep them small. For example, use
8-bit, mono quality at 22Khz sampling rate.
You may want to create a separate folder for your wave files so you
can locate them easily in one place.
5. From the Voice Editor screen,
click on the Add button to display
the Add Wave File window.
6. Copy the wave files that you
recorded to the database. Close
the window when done.
ASUS P4GE-V motherboard user guide
7. Click a POST event on the Voice
Editor screen, then on the Edit
button. The Event Sound Editor
window appears.
8. Locate and select your wave file
for the event then click on the
arrow opposite Voice1. The file
you selected appears on the
space next to it.
9. Click OK to return to the Voice
Editor screen.
10. Do steps 7 to 9 for the other
11. When done, click the Save
button. A window appears
prompting you to save your
12. Type a file name with a .flh
extension, then click Save.
13. Click on the Write button to
compress the file and copy into
14. Click Yes on the confirmation
window that appears.
If you receive an error message telling you that the files exceed the total
allowable size, do one or all of the following.
• Try to modify your messages to make them shorter
• Save the wave files at a lower quality
• Skip lesser used events like FDD Detection, IDE HDD Detection, etc.
Chapter 5: Software support
5.3.5 Multi-channel audio feature
The ADI AD1980 AC ‘97 audio CODEC provides 6-channel audio
capability. Install the SoundMAX Audio Driver and Application from the
support CD that came with the motherboard package to activate the
6-channel audio feature.
You must use 4-channel or 6-channel speakers for this setup.
Setting to multi-channel audio
After installing the audio driver, you can adjust the audio settings to avail
the 6-channel audio feature onboard.
1. From the taskbar, double-click on
the SoundMAX Digital
Integrated Audio icon to display
the SoundMAX Control Panel.
2. The Listening Environment
screen allows you to set to multichannel speakers, enable or
disable the Virtual Theater
Surround, and select Acoustic
Environments and Virtual Ear.
Sound MAX Digital Integrated Audio icon
3. The default setting is Stereo
Speakers (2-channel). To set to a
6-channel speaker system, click
the arrow under Speaker Setup to
display a list of options.
4. Select the option Surround
Sound Speakers (5.1 Surround).
5. Click the Apply button.
6. Click the Test button to display the
Test Listening Environment
7. Click the arrow under Select
Audio Path to display a list of
options. Choose your desired
ASUS P4GE-V motherboard user guide
8. After selecting an option, test your
setting by clicking the Play Test
Noise button. While testing, you
will see a black circle moving on
the screen indicating the audio
The Play Test Noise button
becomes Stop Playing button.
Click this button at any time to
stop playing.
Audio path indicator
9. Click the Close button when done.
10. The MIDI Music Synthesizer
screen allows you to select a
setting for the MIDI.
11. Click the arrow under Synthesizer
Default Set to display a list of
options. Choose your desired
12. Click Apply, then click OK when
Chapter 5: Software support
Adjusting the volume settings
1. After rebooting the system, click on the volume control icon on the
taskbar (lower right corner of your desktop) to display the Volume
Control panel.
Volume control icon
2. If you installed an S/PDIF module,
click on the Volume Control Advanced
button from the Volume Control panel.
The Advanced Controls for Volume
Control window appears.
To achieve 6-channel audio capability
when playing DVDs, check the boxes
opposite AC3 SPDIF and PCM SPDIF.
Click Close.
You do not need to do step 2 if you did not install an S/PDIF module.
ASUS P4GE-V motherboard user guide
Adjusting the microphone settings
1. Click on the Microphone Advanced
button to display the Advanced
Controls for Microphone window.
2. Check the box opposite Mic2 Select to
enable the front panel microphone, if
you installed a front panel audio device
such as the ASUS iPanel.
3. Click Close to effect the new setting.
The rear panel microphone is automatically disabled when you enable
the front panel microphone. Only one microphone port works at a time.
Rear panel audio ports function variation
The functions of the Line Out (lime), Line In (blue), and Mic (pink) ports on
the rear panel change when you select the 4-channel or 6-channel audio
configuration as shown in the following table.
Light Blue
Line In
Line In
Line Out
Front Speaker Out
Front Speaker Out
Mic In
Rear Speaker Out
Rear Speaker Out
Windows 98SE only supports 4.1 channel speaker setting.
Chapter 5: Software support
This part contains an alphabetical list of the
topics found in this document.
ASUS P4GE-V motherboard
Accelerated Graphics Port 2-15
Acrobat Reader 5-5
ASUS EZ Flash 1-4, 4-1
ASUS EZ Plug™ 1-3, 1-8, 2-21
ASUS MyLogo™ 1-4, 5-10
ASUS PC Probe 5-12
ASUS POST Reporter 1-4, 5-17
ASUS Q-Fan 1-4, 4-33
ASUS Update 5-5
Audio CODEC 1-9
Automatic Power Up 4-32
Central Processing Unit (CPU)
fan connector 2-9
installation 2-5
Level 1/Level 2 Cache 4-19
Speed 4-17
CPU socket 1-8, 2-5
Chip Configuration 4-21
Clear RTC RAM 2-17
Concurrent PCI 1-5
ASUS EZ Plug™ 1-3, 1-8, 2-23
ASUS iPanel 2-31
ATX power 1-6, 2-27
chassis intrusion 2-22
fan 2-24
floppy disk 1-6, 2-18
front panel audio 2-28
game/MIDI 2-26
IDE 1-9, 2-19
IDE LED 2-18
infrared 2-27
internal audio 2-26
panel 2-29
power supply thermal 2-24
S/PDIF 2-28
SMBus 2-22
USB header 2-25
Advanced Menu 4-17
Boot Menu 4-35
Boot Sequence 4-35
Exit Menu 4-37
Language 4-11
Legend Bar 4-8
Main Menu 4-10
Menu Bar 4-8
Power Menu 4-29
Setup Defaults, loading 4-38
Setup Program 4-7
Sub-menu, launching 4-9
Updating 4-1
BIOS Beep Codes 3-1
BIOS AFLASH utility 4-3
Boot Device
selection 4-35
Boot Up NumLock Status 4-16
Boot Virus Detection 4-36
DDR SDRAM technology 2-10
Digital audio interface 1-3
installing 2-12
removing 2-12
DIMM sockets 1-10
Double Data Rate (DDR)
memory 1-2
ASUS P4GE-V motherboard user guide
Expansion card
installation 2-13
configuration 2-13
Expansion slots 1-9, 2-13
AGP 1-10, 2-15
PCI 1-10, 2-15
Auto-Repeat Delay 4-16
Auto-Repeat Rate 4-16
Flash ROM 1-9
Floppy 3 Mode 4-10
Floppy disk access control 4-24
Hard Disk Drives (HDDs)
CHS Capacity 4-14
Cylinders 4-14
Heads 4-14
LBA Capacity 4-14
Primary/Secondary Master 4-12
Primary/Secondary Slave 4-12
Sectors 4-14
Types 4-12
Hardware Monitor 4-33
installation 2-7
IRQ assignments 2-14
JumperFree mode 2-16
Clear RTC 2-17
keyboard power 2-16
wireless PCI / USB 2-16
AGP warning 1-10, 2-3
standby power 1-10, 2-3
Legacy Diskette 4-10
major components 1-6
IRQ Table 2-14
layout 2-2
placement 2-1
screws 2-1
Multi-sector transfers 4-15
Operating system
installation 5-1
Overclocking features 1-5
Parallel Port 1-10, 4-24
Modes 4-25
Supervisor 4-11
User 4-11
PCI Configuration 4-26
PCI Latency Timer 4-26
PCI/VGA Palette Snoop 4-26
PIO Mode 4-15
Plug & Play O/S 4-35
Power Management 4-28
Power On Self Test 4-35
PS/2 Keyboard Port 1-10
PS/2 Mouse Port 1-10
PS/2 Mouse
Function Control 4-19
clearing 2-17
Active Precharge Delay 4-22
CAS Latency 4-21
Configuration 4-21
Idle Timer 4-22
RAS Precharge Delay 4-22
RAS to CAS Delay 4-21
Serial Ports 1-10, 4-24
SMART Monitoring 4-15
Sony/Philips Digital Interface
(S/PDIF) 1-3, 2-28
Super I/O controller 1-9
Support CD 5-1
ASUS Update 5-9
Utilities menu 5-5
Drivers menu 5-2
motherboard information 5-7
multi-channel audio 5-21
Technical Support Form 5-8
Suspend Mode 4-29
System Controller
North Bridge 1-8
South Bridge 1-9
System Date 4-10
System memory
configurations 2-11
System Time 4-10
UART2 4-24
Ultra DMA Mode 4-15
USB Legacy Support 4-20
USB ports 1-10
Video memory cache
USWC 4-22
UC 4-22
ZIF socket 2-5
ASUS P4GE-V motherboard user guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF