Mytee | M-3 | User manual | Mytee M-3 User manual

Mytee M-3 User manual
Instructions for
8070 Mytee-Lite™
Please read before use.
Register your product
at http://www.mytee.com/
support/register
Model #
Set up p. 2
General information p. 6
Parts & pricing p. 9
Wiring diagram p. 11
Notes p.12
Serial #
Form # ADP-8070
5-14
13655 Stowe Dr., Poway, Ca. 92064
1
8070 MYTEE-LITE™
FRONT
BACK
1
8
2
3
9
4
10
11
7
5
14
6
13
12
8. Basket
9. Recovery tank drain
10. Service latch
11. Switch plate
12. 25’ single power cord
13. 6” wheels
14. 2” casters
1. Hose hanger
2. Recovery tank lid
3. Cuff-Lynx™ vacuum hose connector
4. Open fill for solution tank
5. Solution hose connector
6. Solution tank drain
7. Solution tank faucet fill
CONNECTING THE HANDLE
ACCESSORIES
8400 - 4” Stainless Steel Upholstery Tool
850 1 - 15’ 1-1/4” Vac/Sol Hose
In the rear of the machine, with handle/basket facing
outward, line up the four inserts on the handle with the
four inserts on the machine, located on the top sides of
the recovery tank. When installing the handle on your new
Mytee-Lite™, make sure you use a hand tool (screwdriver)
for the screws and NOT a power tool. This will insure you
do not strip the hole and puncture the recovery tank.
H122 Cuff-Lynx™ - 2” Female Reducer
2
8070 MYTEE-LITE™
FILL SOLUTION TANK
EMPTY SOLUTION TANK
To fill the solution tank, use a bucket to pour water into
the tank’s opening located at the front of the unit. You can
also use the easy faucet fill also located at the front of the
unit. For best results, fill with warm water (140o F).
To empty any remaining water in the solution tank, remove
cap which is located at the front of the solution tank.
ATTACH HOSES
PUMP SWITCH
Attach female end of a solution hose to a wand or tool
and the male end to the Mytee-Lite’s QD. Then connect
a vacuum hose to a wand and the male Cuff-Lynx™
hose port.
After the machine has been plugged into a 20 amp
grounded outlet, turn on pump. Key tool until upholstery
tool releases a steady flow.
3
8070 MYTEE-LITE™
VACUUM SWITCH
HEATER SWITCH
Turn on vacuum motor and begin cleaning. For best
results make two dry passes for every wet pass.
Release tool trigger. Turn on heater. Wait 8 – 10 minutes
for unit to pre-heat. Once heated, re-key upholstery tool
until hot water begins flowing. Once hot water is flowing,
release trigger and pre-heat an additional 4 – 5 minutes.
RECOVERY TANK DRAIN
VACUUM STACK FILTER
Located at the rear of the Mytee-Lite™ is a bucket high
drain valve. Simply unscrew the tethered cap to release
the recovery water.
The Mytee-Lite’s™ internal filter must be cleaned regularly and is located in the recovery tank. Twist the filter
to remove then clean and replace. If the filter is torn or
damaged, replace with a new one.
4
8070 MYTEE-LITE™
SYSTEM MAINTAINER
SERVICE LATCH
Weekly flushing of the solution system with Mytee System
Maintainer helps keep lines clean and prevents chemical
build-up, improving pump life, performance and pressure.
To open lower housing flip-up latch that is located in the
back of the unit. Twist counter clockwise for release.
To close unit, place latch, twist clockwise and press latch
to secure.
DEFOAMER
Add defoamer in the recovery tank to reduce foam, prolonging the life of the Mytee Lite™ vacuum motor .
5
GENERAL INFORMATION
Dear Customer:
Unpacking the Machine
Keep in mind that the 8070 Mytee -Lite™ is a machine, so neglect or abuse
will cause unnecessary damage and void the warranty. However with simple
maintenance the 8070 will give quality performance for many years to come.
Caution and Warnings
Congratulations on the purchase of your new 8070 Mytee -Lite™. As you are
already aware, the scene of the equipment world is becoming more high tech, and
we at Mytee Products Inc. strive to keep you on the cutting edge with superior
quality and technology.
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to file a
freight damage claim.
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
If warranty questions arise, please consult your user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts or
ordering parts, please call an authorized Mytee Products Inc. Service Center.
To see an updated list, visit our website at www.mytee.com
Is used to warn of immediate hazards that will cause severe personal injury or death.
Before you begin cleaning, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Is used to call attention to a situation that could cause severe personal injury.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical shock. This machine is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must
be plugged into an appropriate outlet that is properly installed in accordance with all
local code and ordinances. Do not remove ground pin; if missing, replace plug before
use.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.
To reduce the risk of fire, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
3. Always unplug power cord from electrical outlet before attempting any adjustments
or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp
edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not in use.
10. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
11. Do not use in areas where flammable or combustible material may be present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.
14. Keep hair, loose clothing, fingers, and all parts of the body away from all
openings and moving parts.
15. Use extra care when cleaning on stairs.
16. To reduce the risk of fire or electric shock, do not use this machine with a solidstate speed control device.
17. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alkalines, or other dangerous liquids.
19. Do not leave operating unattended.
Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service person if you are in doubt
as to whether the outlet is properly grounded. Do not modify the plug provided with
the machine. If it will not fit the outlet, have a proper outlet installed by a qualified
electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualified electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Grounded Outlet
Adapter
Metal
Screw
Grounding Pin
Grounded Outlet Box
Figure 1
Parts and Service
Figure 2
Filling the Solution Tank
Tab for Grounding
Screw
1. Fill the solution tank with the approved cleaning solution.
2. Do not fill up the solution tank completely: 1” should be left free at the top.
3. Typically, the solution should be a mixture of water and a cleaning chemical
appropriate for the type of job.
4. Always follow the dilution instructions on the chemical container label.
5. The temperature of the cleaning solution must not exceed 70oC/160oF.
Figure 3
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the Model and Serial Number
when discussing your machine.
Name Plate
Use only non-flammable liquid in this machine.
The Model and Serial Number of your machine are shown on the Nameplate on the
back panel of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
6
GENERAL INFORMATION
Maintenance Schedule
Setup
1. Fill solution tank with water or approved cleaning agent. For best results, fill with
warm water (140o). Replace vacuum tank.
Flammable materials can cause an explosion or fire. Do not use flammable solutions
or materials in tank(s).
FOR SAFETY: When using machine, follow mixing and handling instructions on
chemical containers.
ATTENTION: If using powdered cleaning chemicals, mix prior to adding.
Maintenance item
Daily
Clean and inspect Tanks
Clean and inspect Hoses
Check power supply cable
Clean machine with all purpose cleaner and cloth
Check spray nozzles
Flush solution system with Mytee system maintainer
Remove and clean float shut-off screen from tank
Inspect vacuum hoses for holes and loose cuffs
Inspect machine for water leaks and loose hardware
x
x
x
x
Once a week
x
x
x
x
x
Trouble Shooting
2. Attach solution hose (located front of machine). NOTE: Make sure the quick
disconnect snap together firmly. As you do this, always inspect hoses for cracks or
fraying. Do not use if hoses are damaged.
3. Attach other end of solution hose to cleaning tool.
4. Attach vacuum hose to recovery tank.
5. Plug machine’s cord into a grounded wall outlet. FOR SAFETY: Do not operate
machine unless cord is properly grounded. FOR SAFETY: Do not operate machine
with the use of an extension cord.
6. Turn on pump. Key tool until you have a steady flow.
7. Release tool trigger. Turn on heater.
8. Wait 8–10 minutes for unit to pre-heat.
9. Re-key upholstery tool until hot water begins flowing.
10. Once hot water is flowing, release trigger and pre-heat an additional 4–5 minutes.
11. Turn on vacuum motor.
12. Begin cleaning. Make two dry passes to every wet pass.
13. For floor cleaning, unplug tool and attach floor wand.
14. Work away from cords to avoid damage.
15. Use a defoamer in your recovery tank.
16. To clean heavily soiled areas, repeat cleaning from different directions.
17. When vacuum tank is full, empty tanks.
18. When work is complete, unplug cords and hoses.
19. Wrap and clean hoses. Clean all tanks.
There is no power.
1. Plug machine in proper outlet.
2. Check circuit breaker; reset circuit breaker, other items should not run on the
same circuit as machine. Outlet must be a 20-amp circuit.
Pump does not work properly.
1. Snap quick disconnects firmly together.
2. Check solution tank; may be empty.
3. Jets clogged, remove jet and flush clean.
4. Filters clogged, remove filters and rinse clean with water.
5. Heater is blocked; flush out with Mytee’s system maintainer.
6. If brass check valve is stuck replace valve.
7. Check pump wire. May need to reconnect wire.
8. Switch plate switch may need to be replaced.
9. If pump motor brushes are worn, replace pump.
Heater does not work properly.
1. If sensor mounted on the heater has popped, reset sensor by pushing in button.
2. Heating element may need to be replaced.
Vacuum motor does not work properly.
1. Check that hose is tightly connected.
2. Close drain hose valve completely.
3. Check and clean foam filter located in recovery tank.
4. If water is coming out of vacuum motor, use a low foaming detergent.
5. Clean upholstery tool or floor wand jets.
Pre-Operation
1. Vacuum carpet and upholstery and remove other debris.
2. Perform machine setup procedures.
3. Inspect power cord for damage.
Accessories (optional)
Operation
2200 Airmover
3601 System Maintainer
2700 Mytee-Dry
8390C-EZ
8700 Crevice Tool
3000 Tradewind™
1. Turn pump switch on.
2. Pull up on tool lever to release air in the line. Hold lever until a steady flow of water
comes out of the wand.
3. Once pump is primed and there is pressure in the solution line, turn on heater switch
(if model is equipped with heater) and wait a few minutes for water to heat up.
4. Once water is heated, turn on vacuum and begin cleaning.
Note: When cleaning upholstery, always check manufacturer’s cleaning instructions.
FAQs
Q: How much does the 8070 weigh and what are the dimensions?
A: 43 Pounds - Dimensions are w/handle: 33” x 12 3/4” x 37”,
w/o handle: 21 1/2” x 12 3/4” x 28 1/2”.
1. Work away from outlet and power cord to prevent cord damage.
2. Use a recommended foam control solution in the recovery tank to prevent vacuum
motor damage. Periodically check for excessive foam buildup in solution tank, and
recovery tank.
3. To clean heavily soiled areas, repeat cleaning path from different direction.
4. When vacuum tank is full, it is time to empty the dirty water from the recovery tank,
and refill solution tank.
5. After cleaning, relieve water pressure from tool before disconnecting hose.
Squeeze trigger for five seconds after turning main power switch off.
Shipping weight is 72.5 lbs. and shipping dimensions are 31 3/4” x 17 1/4” x 41 3/4”
Q: What comes standard with the 8070?
A: The 8070 comes with 15’ 1-1/4” Vacuum/Solution Hose (8501), a 4” Stainless
Steel Upholstery Tool (8400) and Cuff-Lynx™ H122.
Q: Does Mytee recommend a tool for the machine?
A: A variety of tools can be used with the unit, including our 8390 wand, 8700 crevice
tool, and 8400 upholstery tool.
After Use
Q: Where do I plug the machine in?
A: The 8070 requires a 20A grounded circuit. Please note: GFI outlets may trip
before the breaker setting.
1. Unplug.
2. Empty solution tank and rinse it with clean water.
3. Inspect hoses and replace if damaged.
4. Attach 45o drain elbow to dump valve and lift up drain valve lever to empty
recovery tank.
5 Inspect solution filter. Clean or replace if damaged.
6. Store the machine in a clean, dry place.
7. Open recovery tank cover to promote air circulation.
8. Do not expose to rain. Store indoors.
Q: What is the proper pre heat cycle for the 8070?
A: Turn pump switch to the on position and prime pump through the solution hose
and the tool. Then turn the heater switch to the on position. Let the machine sit idle
for 8-10 minutes. Spray tool until you feel the hot water from the jet. Let machine sit
idle for an additional 3-5 minutes. This will insure the water in the heater and hoses
will be at the hottest point to start cleaning.
7
GENERAL INFORMATION
Q: Are the pumps re-buildable for the 8070?
A: Yes, both the seals and the pistons have repair kits available.
Please see the pump manual that shipped with your machine for the
maintenance schedule.
If any provision or portion of this limited warranty policy is found to be unenforceable,
then the remaining provisions and portions shall remain valid and enforceable.
If any provision or portion of this limited warranty policy is found to be limited by law,
then that provision or portion shall be construed to make it effective within the
bounds of law. For example, if there are legal limitations on the duration of warranties, the warranties made herein shall be construed to have the minimum duration
required by law, or, if there are legal limitations of exclusion of remedies, the exclusions made herein shall be construed to apply to the fullest extent possible without
violating the law.
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow excess
moisture in the vacs to dry off. You should also run a System Maintainer through
the system to keep the hoses, pump, and heater clean and free of debris.
Warranty
The validity, construction and performance of this warranty policy shall be governed
by the laws of the State of California, without respect to conflicts of laws principles.
The exclusive jurisdiction of any legal action arising from or related to this warranty
policy shall be in the State of California and no legal action shall be commenced
elsewhere.
MYTEE LIFETIME LIMITED WARRANTY POLICY
Mytee Products, Inc. endeavors to provide high quality products and product support
to its customers and therefore backs up all of its new products purchased from Mytee
Products Inc. (“Mytee”) or any authorized Mytee distributor/service center with this
lifetime limited warranty. This limited warranty begins on the date of the customer’s
purchase and is valid and available to the original purchaser with proof of purchase,
and is not transferable. Mytee’s products are for commercial use only and are not
intended for personal, family or household uses.
Return Material Authorization Procedure
It is the responsibility of any Authorized Service Center (ASC) or Distributor with
written authorization to ensure the Customers equipment is repaired as soon as
possible. Only Mytee Products Inc. or it’s authorized dealers with written authorization, service centers, and agents may make warranty repairs on these products. All
others do so at their own risk and expense.
HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that its rotationally-molded housings will be free from manufacturing defects. This warranty covers
the cost of replacement or repair only and does not cover shipping or labor costs.
The Distributor must follow Mytee Products, Inc. standard RMA procedure:
WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for
90 days from the date of original purchase. “Wear parts” are items which wear out
as a result of usage or the passage of time and are consumed despite attempts to
maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals,
hoses, switches, thermostats, plastisol parts, filters, bearings, brushes, solenoids, orings, bulbs, heating elements, castors, or other parts deemed wear items in Mytee’s
sole discretion. This warranty covers the cost of replacement only and does not cover
shipping or labor costs.
1. When a repair falls within the Warranty time period for a piece of equipment, the
Distributor will fill out a RMA/Warranty claim form. This form will act as a repair order
to replace any defective parts.
2. All defective parts must be returned to Mytee Products, Inc. with the RMA/claim
form for evaluation at the customer’s expense. This shipping is non-refundable. All
warranty claims are subject to an evaluation by Mytee Products, Inc. to determine if
warranty will be approved. Any credit for repair and/or parts will only be issued upon
evaluation and approval from Mytee Products, Inc.
PUMP, VACUUM MOTOR AND HEATER ONE-YEAR LIMITED WARRANTY: Mytee
warrants that pumps, vacuum and floor machine motors, and heaters will be free
from manufacturing defects, defects in workmanship, and defects in material for one
(1) year from the date of original purchase. This warranty does not apply and is void
if the pump, vacuum motor, or heater has worn brush motors, water damage, chemical build-up, chemical damage, or evidence of abuse, neglect or tampering. This
warranty covers the cost of replacement or repair only and does not cover shipping
or labor costs.
3. When Warranty is approved, the Distributor’s account will be credited for the
replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s)
to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be
credited for any parts sent for this claim.
HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY,
EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE
PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES
NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT
ANY TIME WITHOUT NOTICE.
LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR
OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE REMEDY UNDER
ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO
EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES.
All limited warranties are void for, and Mytee does not warrant in any way, any product that evidences misapplication, improper installation, abuse, lack of maintenance,
negligence in use or care, abnormal use, alteration of design, modification, use of
incompatible or corrosive chemicals, use in a rental service, and/or servicing, installation of parts, or repairs by anyone other than Mytee or a Mytee authorized distributor
or service center. Mytee may make changes in products it manufactures and markets
at any time; these changes are made without obligation to change, retrofit, or upgrade any product previously sold or manufactured.
Mytee has no obligation to honor the limited warranties set forth herein unless the
original purchaser, promptly upon discovering the warranty claim and prior to continuing to use the product, contacts Mytee or a Mytee authorized distributor or service
center to describe the claim and to receive and follow instructions for documenting
and resolving the claim. In addition, the purchaser must provide the product to which
the claim applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection. In addition, the purchaser must provide/return the product intact,
unmodified, with all of its original parts.
8
Order parts at: www.mytee.com/products/8070-mytee-lite-ii-automotive-detail-extractor/#.UtltKv16ho5
9
A
B
C
D
E
F
H203
H210
H216
H213
13
14
15
16
H427
H279
H042
29
30
31
32
Part prices are subject to change.
E519
E573
55
56
8
B108
B207
52
H903A
B103
51
54
B107
50
53
B170
PH634-13
C305
47
49
B105
46
48
AH157
45
G068
42
B136
H486
41
44
H221
40
H256
H310
39
43
E532
H445
37
38
E515
H212
28
H343
P585
27
36
H273
26
35
H681
25
H241
PH612-48
24
34
H178
23
H254
C302P
22
33
P584
G004
21
B119
G021
12
H379
G022
11
20
G031
10
19
P560
9
H201
G055
8
H846B
H688-A
7
18
H222
17
G036
6
3
5
P583
H312
2
H230
H135
4
PART NO.
1
8
ITEM
NO.
7
Thermostat, 200°, Auto, 1/4"
heating rod, 1000W, 115V
heater, aluminum cast, single
valve, brass, 1/4" check
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
nipple, brass, 1/4"m, hex
sol hose, 1/4" silicone braided, clear
ferrule, 1/4" brass
pump, 120 psi, 115V
bushing, brass, 3/8"mpt x 1/4"
hose, 3/8" x9" (OAL), f x fsw
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
screw, 10-32 x 3/4" phil pan head, zinc
bumper, 7/8" x 1/4" head
latch, front
nut, lock, 1/2" steel
plate, switch, MyteeLite, 3 hole
fitting, strain relief, w/ spring, 1/2" npt
power cord, end, 25', 14/3
switch, rocker, 2 position
screw, 10 x 5/8" hex head, zinc
axle, 13.63" x .50" dia
washer, axle, cut 1/2" id
c-clip, 12mm, external
wheel, 6"
washer, wave, axle
flat washer, 9/16"ID x 1 1/16"OD
base, MyteeLite
nut, kep, #10-32 zinc
caster, 2", black hub, gray tread
clear tubing, 1/2" OD x 3/8" ID, faucet fill
faucet fill
vac motor
gasket, vacuum motor
sol tank, MyteeLite
filter, strainer, 1/4"
bracket, front, small
cap, gallon jug, 1-5/8"
bolt, 1/4-20 x 1/2" hex head, zinc
washer, 1/4" lock, s/s
nut, lock, 1/4-20, nylon insert, s/s
washer, 1/4" flat, s/s
bolt, 1/4-20 x 1-1/4" hex head, s/s
screen, mesh filter, 2-3/8" dia
filter, foam, 2-3/8" x 1"
gasket, 3.25" i.d. x 5.88" o.d.
cap, 6", threaded
tether, cap, 6 1/2"
handle, MyteeLite
screw, 10-32 x 1-1/4" phil pan head, s/s
cap, 2.5" threaded, tethered
screw, 10-32 x 1/2" phil pan head, s/s
plate, connecting, MyteeLite
vac tank, MyteeLite
Cuff-Lynx, 2" m cuff x 2" mpt
DESCRIPTION
7
1
1
1
1
2
1
2
1
2
1
2
1
3
2
2
1
1
1
1
1
3
4
1
2
2
2
2
4
1
15
2
1
1
1
2
1
1
1
1
2
2
2
6
2
1
1
1
1
1
1
6
1
28
4
1
1
QTY.
6
$16.49 ea
$51.99 ea
$78.99 ea
$13.99 ea
$5.99 ea
$4.49 ea
$3.19 ea
$6.49 ft
$0.99 ea
$151.99 ea
$3.19 ea
$25.99 ea
$4.99 ea
$0.99 ea
$1.99 ea
$13.99 ea
$1.99 ea
$6.99 ea
$8.99 ea
$44.99 ea
$13.99 ea
$0.99 ea
$15.99 ea
$0.99 ea
$0.99 ea
$25.99 ea
$1.49 ea
$0.99 ea
$89.99 ea
$0.99 ea
$8.99 ea
$1.99 ft
$10.99 ea
$148.99 ea
$8.99 ea
$149.99 ea
$3.99 ea
$3.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$4.99 ea
$2.99 ea
$6.99 ea
$23.99 ea
$12.99 ea
$65.99 ea
$0.99 ea
$3.49 ea
$0.99 ea
$6.99 ea
$159.99 ea
$3.99 ea
MSRP
6
59
B102
62
5
sol hose, 1/4" x 16' 1", 3000 max psi
strap, velcro, w/buckle
sol hose, pigtail, 1/8 x 7 1/2
A942
G147
A935
manaul, Mytee-Lite
4
stop sign, register your product
AD127
instruction giude, Cuff-Lynx
Cuff-Lynx, 1.25" hose cuff x 2" female cuff
tool, upholstery w/valve
ADM-8070
ADM-CUFF-LYNX
H122
H282
hose, vac, 15' x 1-1/4" w/ 1 1/2 black cuffs
quick disconnect, 1/4" female x 1/4" fpt
H701
quick disconnect, male, 1/4" male x 1/4" fpt
DESCRIPTION
qd, brass, 1/4" f x 1/4" fpt
plate, mounting, QD
45 deg, street elbow, brass, 1/4" male
hose, pulse, 3/8" x 14-1/2" (OAL), f
screw, 6 x 3/16, phil pan head, self-tapping
B101
5
DESCRIPTION
Thermostat, 310°F ± 10°F, Manual, 1/4"
4
B102
PART NO.
ITEMS NOT SHOWN
H484
61
B130
H274
AH184
58
60
E574
PART NO.
57
ITEM
NO.
1
1
1
1
1
1
1
6
1
1
2
QTY.
1
1
1
1
5
1
QTY.
$3.99 ea
3
$98.99 ea
$43.99 ea
$14.99 ea
$3.99 ea
$71.99 ea
$17.49 ea
$8.49 ea
MSRP
$17.99 ea
$4.99 ea
$5.49 ea
$27.99 ea
$0.99 ea
$17.99 ea
MSRP
3
DATE
1/2014
NAME
M.LaBarbera
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
COMMENTS:
CHECKED
DRAWN
2
SCALE: 1:24
1
DO NOT
SCALE DRAWING
8070
SIZE DWG. NO.
C
B
SHEET 1 OF 3
REV
PRODUCTS, INC.
858-679-1191
MyteeLite II
(2014)
mytee
TITLE:
1
A
B
C
D
E
F
8070 MYTEE-LITE™ PARTS & PRICING
10
A
B
C
D
E
F
8
8
7
6
5
7
7
4
4
3
12
11
10
9
8
2
6
6
1
3
4
5
5
21
22
23
22
50
to pump
"IN"
thru B106A
20
17
19
29
24
36
4
16
20
15
18
to sol tank
thru B119
25
4
14
13
35
37
32
33
38
29
27
43
28
27
14
46
53
to heater
"IN"
thru
41
44
3
30
4
31
40
34
39
45
3
27
42
47
4
45
to pump
"OUT"
thru AH157
53
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
62
54
SCALE: 1:24
1
DO NOT
SCALE DRAWING
8070
B
REV
SHEET 2 OF 3
MyteeLite II
(2014)
PRODUCTS, INC.
50
to QD
thru B107
60
1
858-679-1191
59
SIZE DWG. NO.
C
TITLE:
mytee
4
55
50
52
29
61
DATE
60
PROPRIETARY AND CONFIDENTIAL
COMMENTS:
58
to heater
"OUT"
thru
50
44
51
1/2014
52
57
NAME
56
6
49
M.LaBarbera
48
44
CHECKED
DRAWN
26
46
2
A
B
C
D
E
F
8070 MYTEE-LITE™ PARTS & PRICING
1/15/2014
L2
L1
G
Primary Cord
11
E-515
E-515
E-515
1000 Watt Heat
G
L1
L2
Pump
VAC
L2
C-305
C-302P
L1
G
G
8070
115 Volt System
To Metal
Plate
8070 MYTEE-LITE™ WIRING DIAGRAM
NOTES
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising