JT1000 Series
JT1000 Series
Parts List
268
3/99
JT1000 Series
Parts List
REF.
NO. PART NO.
1
2
4505896U01
3205902U01
3A
3B
4
1505637V04
1505637V05
----
5A
5B
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
7505870U01
7505870U02
5105238U83
3305183R55
3305409X06
3505535X02
---0705470V01
---1405330W02
8405310W04
8405641V01
3905517V01
3605253V01
3605636V01
1305633V01
3605635V01
1305698V01
3205160W01
2205159W01
3205514W01
3205177Z01
3205178Z01
DESCRIPTION
Lever, PTT
Seal, PTT, and Actuator for S404,
S405, S406, and S408
Cover, Front; Full Keypad
Cover, Front; Limited Keypad
Label, Agency Approval; not field
replaceable
Keypad, 15-key
Keypad, 6-key
Module, Display
Label, Motorola
Label, JT1000
Felt, Speaker
Speaker (LS401)
Bracket, Speaker Retainer
Microphone
Boot, Microphone
Flex, Front Cover/Display
Flex, Controls
Popple, PTT (p/o S406)
Knob, On/Off/Volume
Knob, Frequency
Ring, Concentric; Escutcheon
Knob, Concentric Ring
Escutcheon, Control Top
Seal, Actuator; for S101
Pin, Actuator; for S101
Seal, Accessory Connector
Seal, Control Top
Seal, Emergency Button
REF.
NO. PART NO.
27
28
29
2705877U01
-------
30
31
32
33
34
3905329W01
------1505632V01
----
35
36
4205507X01
8405247V01
37
38
39
---3205820V02
----
40
41
42
43
44
45
46
47
48
3205176Z01
2605891U02
------4105266V01
4405524V01
1405307X01
REX4575A
3905838V01
49
2605898U01
50
7505393N33
DESCRIPTION
Housing, Switch
Switch, Toggle (S402)
Potentiometer/Switch,
On/Off/Volume Control (R401/S403)
Popple, Emergency Button
LED (CR702A/CR702B)
Switch, Frequency (S401)
Cover, Switch Housing
Spring, PA; not field replaceable,
order front shield (item 41)
Strain Relief
Connector, Strip (P301/P704)
Flex, Jumper (early version radios)
Plug, Connector (P404)
Seal, Connector Plug
Label, Rear; Information;
not field replaceable
“O” Ring, Contoured/Seal, Antenna
Shield, Front
Switch, RF (S101)
Label, Barcode; not field replaceable
Spring, RF Switch
Piston, RF Switch
Insulator
Chassis (Rear Cover)
Contact, Antenna Shield Ground
(800 MHz and 900 MHz radios only)
Shield, PA (800 MHz and 900 MHz
radios only)
Pad, Shock
http://accesssecure.mot.com/Accesspoint
269
3/99
JT1000 Series
Portable Accessories
CHARGERS
CHARGERS
Choose from a variety of voltages with approvals for
maximum application flexibility. Single unit chargers are
available in either desktop or compact styles. Multiple
Unit chargers can be wall or rack mounted. Rapid rate
chargers fully charge the battery in less than three
hours. Standard rate chargers fully charge the battery in
approximately 16 hours.
Single Unit Chargers, Rapid Rate
NTN1168A Enhanced Desktop, 117 Volts*
NTN1169A Enhanced Desktop, 220 Volts (supplied with
2 prong cord)**
NTN1170A Enhanced Desktop, 240 Volts (supplied with
3 flat prong cord)**
NTN1171A Compact, 117 Volts*
NTN1172A
NTN1172A Compact,
220 Volts (supplied with
2 prong cord)**
NTN1173A Compact,
240 Volts (supplied with
3 flat prong cord)**
Single Unit Chargers, Standard Rate
NTN1174A Desktop, 117 Volts*
NTN1175A Desktop, 220 Volts
(supplied with 2 prong cord)**
NTN1176A Desktop, 240 Volts
(supplied with 3 flat prong cord)**
Multiple Unit
Chargers
NTN1177C Six Pocket,
Rapid Rate, 117 Volts
NTN1178A Six Pocket,
Rapid Rate, 220 Volts
NTN1177C
(supplied with 2 prong
cord)
NTN1179A Six Pocket, Rapid Rate, 240 Volts
(supplied with 3 flat prong cord)
NLN7968A Rack Mount
NLN7967A Wall Mount
Enhanced Charger Line Cords
Cords can be used on any enhanced single or multiple
unit rapid charger to provide versatility for charging
capability.
3060665A04 Exchangeable Line Cord, 110V
3060665A05 Exchangeable European 2 Prong Line
Cord, 220V
3002120F02 Exchangeable United Kingdom 3 Prong
Line Cord 240V
Vehicular Charger
TDN9816A Vehicular Charger for
Nickel-Cadmium
Battery
NTN1174A
*Underwriters Laboratory Approved
**VDE Approved
270
3/99
TDN9816A
JT1000 Series
Portable Accessories
BATTERY MAINTENANCE SYSTEM PLUS (BMS Plus)
Using interchangeable battery adapters (sold
separately), the BMS Plus is capable of charging and
discharging, analyzing, conditioning and cycle test on
batteries; tracking battery voltage and capacity (mAh).
The BMS Plus offers a 3 year warranty. Its easy-to-use
design supports hundreds of 2-way, cellular, and
camcorder batteries with printer port* (Serial-RS-232C
port – uses female 9-pin to male 25-pin cable).
WPLN4079AR Six Station, 110V AC, 50/60 Hz
WPLN4080AR Six Station, 230V AC, 50/60 Hz
WPLN4079AR
BATTERY DISCHARGE TESTER
Tester determines a battery's
delivered capacity by
discharging a fully charged
battery. 'LED' indicates cycle
status by turning “ON” when
fully charged battery is placed
in adapter and “OFF” when
discharge is complete. Plug-in
adapters allow one console to
discharge most batteries. No
AC power source required
(console is powered by
RLN4201B
discharging battery).
RLN4201B Single Unit Battery Discharge Tester,
Requires Battery Adapter or Cable/Clip Lead
RLN4048A Battery Adapter
RKN4037A Cable/Clip Lead, 7.5V
*Compatible with the STAR Micronics SP200 series printers,
available from any STAR Micronics distributor, and other printers
with STAR emulation.
Adapter
TDN9435C Standard Adapter, JT1000, NiCd
CDN6364A Standard Adapter, JT1000, NiCd and NiMH
BATTERY OPTIMIZING SYSTEM (BOS)
The Battery Optimizing System
accommodates NiCD, NiMH,
Li-Ion, and SLA. Four
independent stations for
simultaneous service of 4
batteries. Reads battery
capacity in percentage
of nominal rating;
verifies voltage;
measures battery
temperature and
displays battery
impedance in milliohms.
WPLN4071AR
(Adapter sold separately).
WPLN4071AR 4 Station, 110V AC, 50/60 Hz
WPLN4073AR 4 Station, 230V AC, 50/60 Hz
VEHICULAR BATTERY ELIMINATOR
The battery eliminator saves useful battery life by
drawing power from a vehicle's battery. Simply replace
the portable battery with the battery eliminator and plug
in the cigarette lighter receptacle.
RLN4335A Vehicular Battery Eliminator
RLN4335A
Adapter
RL-72403 Adapter for JT1000
http://accesssecure.mot.com/Accesspoint
271
3/99
JT1000 Series
Portable Accessories
CARRYING ACCESSORIES
Carrying Cases
Carrying cases provide a convenient way to carry your
radio while protecting it from the environment. Cases
are designed to fit your radio and are determined by the
type of battery you select. You may select from leather
or nylon construction, standard or swivel attachment and
a variety of other accessories. The swivel attachment
allows the radio to swing freely with body movements.
Standard Carrying Cases
NTN7238A Leather Carry Case with
Belt Loop and T-Strap, for High
Capacity Battery
NTN7239A Leather Carry Case with
Belt Loop and T-Strap for Ultra High
Capacity Battery
NTN7247A Nylon Carry Case with Belt
Loop for High and Ultra High Capacity
Batteries
NTN7894A Nylon Case for Alkaline
Battery
NDN4018B DTMF Leather Carry Case
with Belt Loop for use with high and
ultra-high capacity batteries
NTN7247A
Swivel Carrying Cases
NTN7241A Leather Carry Case with 21⁄2˝ Swivel Belt
Loop and T-Strap for High Capacity Battery
NTN7242A Leather Carry Case with 21⁄2˝ Swivel Belt
Loop and T-Strap for Ultra High Capacity Battery
NTN7244A Leather Carry Case with 3˝ Swivel Belt Loop
and T-Strap for High Capacity Battery
NTN7245A Leather Carry Case with 3˝ Swivel Belt Loop
and T-Strap for Ultra High Capacity Battery
CARRYING ACCESSORIES
The following carry cases have a new, high activity
swivel “D” button and belt loop. Case stays on belt more
securely. To remove case from belt loop, rotate case
180° and slide case upward, out of the holder.
NTN8035A Leather Carry Case with High Activity
Swivel, 21⁄2˝ Belt Loop and T-Strap for High Capacity
Battery
NTN8036A Leather Carry Case with High Activity
Swivel, 21⁄2˝ Belt Loop and T-Strap for Ultra High
Capacity Battery
NTN8037A Leather Carry Case with High Activity
Swivel, 3˝ Belt Loop and T-Strap for High Capacity
Battery
NTN8038A Leather Carry Case with
High Activity Swivel, 3˝ Belt Loop and
T-Strap for Ultra High Capacity Battery
NDN4017B DTMF Leather Carry
Case with High Activity Swivel Belt
Loop for use with high and ultra-high
capacity batteries
NTN8039A 21⁄2˝ Replacement Swivel
Belt Loop for High Activity Swivel
Cases
NTN8040A 3˝ Replacement Swivel
Belt Loop for High Activity Swivel
Cases
NTN1534A High Activity “D” Button
NTN8038A
and 21⁄2˝ Belt Loop
NTN1535A High Activity “D” Button and 3˝ Belt Loop
NTN8063A High Activity “D” Button
Replacement
Swiveller
TDN9684A Swiveller, Includes
Clip Button, Holster and Belt
TDN9690A Clip Button, Mounts
on Battery
TDN9684A
TDN9688A Holster, Compatible
with all Buttons
TDN9687A 2˝ Wide Nylon Belt
TDN9687A
272
3/99
JT1000 Series
Portable Accessories
CARRYING ACCESSORIES
CARRYING ACCESSORIES
T-Strap
Chest Pack
NTN5574A T-Strap for Leather
Carry Cases
NTN7376A T-Strap for Nylon
Carry Cases
Belt Clips
Carry the radio mounted in a pouch on the chest.
Adjustable straps go over shoulders and around waist.
TDN9326A Chest
Pack
HLN6602A
Universal Chest
Pack with Radio
Holder, Pen Holder,
and Velcro Secured
Pocket
1505596Z02
Replacement Strap
HLN6602A
for HLN6602A
4205638V04 Belt Clip, 21⁄2˝
4205638V02 Belt Clip, 3˝
RadioPAK™
NTN5574A
Belt Loops
4205857B01 Swivel Belt Loop, 2˝
4282421J06 Swivel Belt Loop, 21⁄2˝
4205857B01
Belt
4200865599 Black Leather
Belt, 3˝
Carrying Strap
NTN5243A
Shoulder
Carrying Strap
allows easy
carrying of
radio when not
wearing a belt.
4200865599
NTN5243A
It’s different from all other holders or cases: more
comfortable, more useful, and more stylish. Worn
around the waist, it holds two-way, iDEN portables or
cellular phones right at hand. Includes a separate 6˝x8˝
zippered pouch for other on-the-job necessities.
Adjustable nylon weave belt; fits both men and women.
RLN4815A RadioPAK™ radio/utility case
4280384F89 Universal RadioPAK™ belt lengthener; fits
waists larger than 40”
Portable Radio Hanger
The portable radio hanger slides over
and hangs from the door panel in a
vehicle. The radio's belt clip slides
onto the portable hanger allowing
convenient, easy mounting. Two sizes
are available to fit door panels. Belt
clip required to use radio hanger.
TDN9327A Portable Radio Hanger for
Door Panels up to 23⁄4˝
TDN9373A Portable Radio Hanger for
Door Panels 23⁄4˝ to 31⁄4˝
http://accesssecure.mot.com/Accesspoint
TDN9373A
273
3/99
JT1000 Series
Portable Accessories
AUDIO ACCESSORIES
AUDIO ACCESSORIES
Remote Speaker/Microphones
Public Safety Speaker/Microphones
Remote Speaker/Microphone allows
remote transmit and receive
capabilities conveniently while radio
remains in the case. These
microphones include: 6´ Coiled Cord
Assembly, 3.5 mm Earjack, Swivel
Clip, and Quick Disconnect Latch.
NMN6193B Remote
Speaker/Microphone
NMN6191B Noise Cancelling
Remote Speaker Microphone
Public Safety Speaker/Microphones include 4.5´ Straight
Cord Assembly, 3.5 mm Earjack, Swivel Clip, Quick
Disconnect Latch, Antenna Connector, and Receive
Audio High/Low Volume Push Button. Antenna must be
ordered separately.
NMN6228C Noise-Cancelling Public Safety
Speaker/Microphone
NMN6193B
Epaulet Strap
Black leather epaulet strap
secures remote speaker
microphone to epaulet straps on
shirt or jacket and accommodates
back clip in leather cut-outs.
Snap closure secures remote
speaker microphone cord to allow
reliable communications in hostile
environments.
RLN4294A Epaulet Strap, Velcro
RLN4295A Epaulet Strap, Small Clip
RLN4294A
RLN4295A
Surveillance Accessories
BDN6664A* Beige
Earpiece Assembly with
Standard Earphone and
Urethane Earloop
BDN6726A* Black
Earpiece Assembly with
BDN6664A
Standard Earphone and
Urethane Earloop
BDN6665A* Beige Earpiece Assembly with
Extra Loud Earphone (exceeds OSHA limits) and
Urethane Earloop
BDN6727A* Black Earpiece Assembly with
Extra Loud Earphone (exceeds OSHA limits) and
Urethane Earloop
BDN6666A* Beige Earpiece Assembly with
Volume Control and Urethane Earloop
BDN6728A* Black Earpiece Assembly with Volume
Control and Urethane Earloop
BDN6667A* Beige
Earpiece Assembly with
Microphone and PushTo-Talk Combined
BDN6729A* Black
Earpiece Assembly with
Microphone and PushBDN6667A
To-Talk Combined
*Requires BDN6676 adapter
274
3/99
JT1000 Series
Portable Accessories
AUDIO ACCESSORIES
BDN6668A
BDN6668A* Beige
Earpiece Assembly with
Microphone and PushTo-Talk Separate
BDN6730A* Black
Earpiece Assembly with
Microphone and PushTo-Talk Separate
BDN6669A* Beige Extra Loud Earpiece (exceeds OSHA
limits) with Microphone and Push-To-Talk Combined
BDN6731A* Black Extra Loud Earpiece (exceeds OSHA
limits) with Microphone and Push-To-Talk Combined
BDN6670A* Beige Extra Loud Earpiece (exceeds OSHA
limits) with Microphone and Push-To-Talk Separate
BDN6732A* Black Extra Loud Earpiece (exceeds OSHA
limits) with Microphone and Push-To-Talk Separate
BDN6676B 3.5 mm Threaded Jack Adapter with Quick
Disconnect Latch. Required for use with Above
Surveillance Accessories
5080369E38 Standard Earpiece Assembly (Earphone,
Earloop, Eartip)
5080369E39 Extra Loud Earpiece Assembly (Earphone,
Earloop, Eartip)
5080369E40 Plastic Urethane Earloop
5080369E41 Wire Earloop
5080371E69 Small Rubber Eartip
5080371E73 Standard Rubber Eartip
Flexible Ear Receiver
BDN6719A Ear Receiver with 3.5 mm threaded plug, to
be used with adapter BDN6676
AUDIO ACCESSORIES
Noise Kits
Lightweight translucent tube attaches to Motorola
surveillance accessories. Clothing clip prevents the
accessory from being pulled from the ear due to body
movement or head rotation.
NTN8370A Extreme Noise Kit,
includes 2 foam earplugs for loud
environments
NTN8371A Low Noise Kit, includes
rubber eartip for low noise
environments
5080384F72 Replacement Foam
Plugs. Pack of 50
(for use with NTN8370A)
NTN8370A
Earpiece
The clear comfortable earpiece forms to the inside of
your ear and is perfect for low noise environments.
Compatible with the NTN8371A, clear acoustic tube
assembly, and most surveillance kits (1, 2 and 3 wire).
This earpiece is made of easy-to-clean chemically inert,
hypoallergenic material.
There are 3 items needed to make this product work:
1. Clear Comfortable Earpiece
2. Clear Acoustic Tube Assembly
(NTN8371A)
3. Surveillance Kits
RLN4760A Small Custom Earpiece, right ear
RLN4763A Small Custom Earpiece, left, ear
RLN4761A Medium Custom Earpiece, right ear
RLN4764A Medium Custom Earpiece, left ear
RLN4762A Large Custom Earpiece, right ear
RLN4765A Large Custom Earpiece, left ear
*Requires BDN6676 adapter
http://accesssecure.mot.com/Accesspoint
275
3/99
JT1000 Series
Portable Accessories
AUDIO ACCESSORIES
Pellet Style Earpieces
BDN6780A* Single Earbud with Microphone and PushTo-Talk
BDN6781A* Single Earbud, Receive only
Ear Microphone System
The speaker and microphone elements are housed in
one small earpiece. This compact unit picks up the
voice through bone vibrations in the ear canal. Ideal for
use in high noise environments. Available in PTT or
Voice-activated (VOX) capabilities for total hands free
communications. Order Interface Module separately.
BDN6677A** Ear Microphone
for Standard Noise Levels
(up to 95 dB), Black
BDN6678A** Ear Microphone
for Standard Noise Levels
(up to 95 dB), Beige
BDN6641A** Ear Microphone
BDN6677A
for High Noise Levels (up to
105 dB), Grey
Interface Module
BDN6708B** Push-To-Talk only Interface Module
BDN6671B** Voice-Activated/Push-To-Talk Interface
Module
Optional Accessories
0180358B38**
Remote Push-To-Talk
Ring Switch
0180300E83
Bodyswitch, Push0180358B38
To-Talk Accessory
5080358B28 Eartips, Black, Size Medium (10 per pack)
5080358B29 Eartips, Black, Size Large (10 per pack)
5080358B30 Eartips, Beige, Size Medium (10 per pack)
5080358B31 Eartips, Beige, Size Large (10 per pack)
**Factory Mutual approved
276
3/99
AUDIO ACCESSORIES
0180358B32 Earholder, Black, Size
Small; secures ear mic in ear
0180358B33 Earholder, Black, Size
Medium; secures ear mic in ear
0180358B34 Earholder, Black, Size
Large; secures ear mic in ear
0180358B33
0180358B35 Earholder, Clear, Size Small;
secures ear mic in ear
0180358B36 Earholder, Clear, Size Medium; secures
ear mic in ear
0180358B37 Earholder, Clear, Size Large; secures ear
mic in ear
4280369E44 Replaceable Belt Clip with Screws
0180300E25 Earguard with Adjustable Loop; secures
ear mic in ear
Heavyduty Headsets
Heavyduty headsets include
Noise-Cancelling Microphones
and can be worn with or
without a hardhat. Headsets
are for use in noise levels up
to 125 dB. The Push-To-Talk
switch is located on the
earcup. The Vox module is
contained within the headset
on voice activated units.
Heavyduty headsets require
BDN6645A
radio adapter cable.
(shown with BDN6673B)
BDN6645A Push-To-Talk Headset
with Boom Microphone, Requires Adapter Cable; Noise
reduction rating =24dB
JT1000 Series
Accessories, Antennas
AUDIO ACCESSORIES
PORTABLE ANTENNAS
Flexible Whip Antenna
BDN6635B Voice-activated
Headset with Boom
Microphone, Requires Adapter
Cable; Noise reduction rating
=24dB
Flexible Whip antennas have a one-piece finish and
steel core for optimal radiation characteristics. Provides
more comfort when radio is worn on the belt.
8505241U05
Flexible Whip, 403-520MHz, 6˝
Helical Antennas
BDN6635B
(shown with BDN6673B)
BDN6636B Voice-activated
Headset with Throat
Microphone, Requires
Adapter Cable
BDN6673B Radio Adapter
Cable
BDN6636B
(shown with BDN6673B)
Lightweight Headsets
Lightweight headsets have In-Line
Push-to-Talk Switch. Require
BDN6676B Audio Adapter.
NMN6245A Single Speaker
Lightweight Headset with In-Line
Push-To-Talk Switch (requires
BDN6676B adapter)
NMN6246A Ultralite Headset with
Boom Microphone and In-Line PushTo-Talk Switch (requires BDN6676B
NMN6245A
adapter)
NMN1020A Lightweight Headset with Boom
Microphone to be worn on a helmet or safety glasses.
Includes NKN6498A adapter cable. Requires
BDN6676B adapter. FM approved.
NKN6498A Headset Adapter Cable for use with NMN1020A
Helical are sturdy and dependable for years of failsafe
communication. Each antenna is designed and built to
quality standards. The skirt at the base of the connector
helps to seal out damaging elements. Connector is
made of plated brass material for long life.
8505644V01
Helical, 136-151MHz, 6˝
8505644V02
Helical, 151-162MHz, 6˝
8505644V03
Helical, 162-174MHz, 6˝
8505644V04
Helical, 403-435MHz, 3˝
8505644V05
Helical, 435-470MHz, 3˝
8505644V06
Helical, 470-520MHz 3˝
Wideband Antenna
Wideband antenna is ideal when radio is used in
different frequencies since one antenna will cover all
ranges.
8505518V01
Wideband, 136-174MHz, 6˝
http://accesssecure.mot.com/Accesspoint
277
3/99
JT1000 Series
Kits, Batteries
REPLACEMENT KITS
REX4395A 15-Key Cosmetic Replacement Kit
PORTABLE BATTERIES
Nickel-Cadmium
Part Number:
Charge:
Volts:
Avg. MAH:
Height:
FM Rating:
NTN7143CR
Rapid
7.5V
1200
6˝
(NA)
Part Number:
Charge:
Volts:
Avg. MAH:
Height:
FM Rating:
NTN7144AR
Rapid
7.5V
1400
6˝
(NA)
Nickel Metal Hydride
Part Number:
Charge:
Volts:
Avg. MAH:
Height:
FM Rating:
278
3/99
WPNN4013AR
Rapid
7.5V
2000
6˝
(NA)
NTN7143CR
PORTABLE BATTERIES
Alkaline
Part Number:
Charge:
Volts:
Avg. MAH:
Height:
FM Rating:
NTN7319AR
(NA)
9V
(NA)
6˝
(NA)
Part Number:
Charge:
Volts:
Avg. MAH:
Height:
FM Rating:
NTN8122AR
(NA)
11V
(NA)
6˝
(NA)
JT1000 Series
Service Aids, Manuals
SERVICE AIDS
SERVICE AIDS
Battery Eliminator
RT5144/48/0 Needle-Fine Black Test Probe for High
Density Circuitry
RT5144/48/2 Needle-Fine Red Test Probe for High
Density Circuitry
The battery eliminator acts like a
battery with a cable to access a DC
external power supply. It is ideal to
inspect transmitters and receivers
on incoming radios. Reverse supply
polarity protection and input fuse
protection are provided.
RLN1014A Battery Eliminator
Radio Test and Programming Cable
RLN1014A
Housing Eliminator
RLN1018A Housing
Eliminator
RLN1018A
Radio Service Software
Utilizing your personal computer, this software
enables you to add or reprogram frequencies as your
requirements change. IBM 366 is recommended
for these products. Requires interface box and
appropriate cables.
RVN4098H Programming Software
Radio Interface Box
Adapter
5880348B33 SMA to BNC
RF Adapter
5880348B33
Extractor
Aids in the removal of discrete surface mounted
devices.
6680387A59 Extractor, 2-contact
Heat Controller
6680387A64 Heat Controller with
Safety Stand
6680387A65 Safety Stand Only
Battery Tester
Test battery charge.
RLN4201B Battery Tester
RLN4048A Adapter, MTS2000
nickel cadmium batteries
Links radio programming cable
and computer interface
together. Provides required
voltage shift to enable
communications between radio
and computer. Requires
RLN4008B
computer and interface cable,
radio test and programming
cable, and 9 volt snap type battery (6082728J01).
RLN4008B Radio Interface Box
0180357A57 AC Power Pack, 110V
0180358A56 AC Power Pack, 220V
3080369B71 IBM to RIB Cable, 25 pin
3080369B72 IBM ro RIB Cable, 9 pin
Cloning Cable
RKN4036D Cloning Cable
REFERENCE MANUALS
RLN4201B
Probes
RTL4208A 50 ohm
High Frequency
RF Probe
Used with portable radio test set, RTX4005B, for
transmitter receive alignment and performance checks.
Also used in programming radio.
RKN4035D Radio Test and Programming Cable
RTL4208A
6881200C25
6881200C40
6881078C45
Service Manual
Service Manual
Operator Manual
http://accesssecure.mot.com/Accesspoint
279
3/99
[ HT1000/JT1000/MTX80
RMN4056A Receive-Only Dual Muff
Headband Style Headset; provides
24dB of noise reduction; for use with
NMN6193B and NMN6191B (can be
plugged directly into radio with
BDN6676D adapter)
RMN4057A Receive-Only Headband
Mount mounts easily to hardhats
with slots and provides 22dB of
noise reduction; for use with
NMN6193B and NMN6191B (can
be plugged directly into radio with
BDN6676D adapter)
Remote Speaker Microphones
(RSM)
Allows you to talk and listen without
removing the radio from the belt case or
charger. Ideal for high noise
level environments. These water resistant
microphones include 6.0' coil cord
assembly, 3.5mm earjack,
swivel clip and quick disconnect latch.
NMN6193B† Remote Speaker Microphone
NMN6191B† Noise Cancelling Remote Speaker
Microphone
Public Safety Speaker
Microphones (PSM)
Surveillance Accessories
Public Safety Speaker Microphones include straight cord
assembly, 3.5mm earjack, swivel clip, quick disconnect latch,
antenna connector, and receiver, audio high/low volume push
button. Antenna must be ordered separately. Use radio
antennas on page 15.
NMN6228C† 30" Noise-Cancelling Public Safety
Speaker/Microphone, straight cord
NMN6243B† 18" Noise-Cancelling Public Safety
Speaker/Microphone, straight cord
NMN6244B† 24" Noise-Cancelling Public Safety
Speaker/Microphone, straight cord
RSM Accessories
Epaulet Strap
Black leather epaulet strap secures
remote speaker microphone to
epaulet straps on shirt or jacket and
accommodates back clip in leather
cut-outs. Snap closure secures
remote speaker
microphone cord to allow reliable
communications in hostile
environments.
RLN4294A Epaulet Strap, Velcro
RLN4295A Epaulet Strap, small clip
RLN4294A
Plugged into the 3.5mm earjack on the RSM audio adapter
these audio accessories will mute the speaker on the RSM
allowing the user to discretely hear all incoming messages. Ideal
for noisy environments. The following audio accessories can
also be plugged directly into the radio with the BDN6676D
audio adapter.
9
Surveillance accessories allow the user to privately receive
communications with the earpiece and are ideal when
environments require discrete communications.
The following surveillance accessories require the
BDN6676D (3.5 mm threaded adapter jack) that attaches to
the radio, unless being used with speaker/microphone.
Earpiece Assembly with Standard Earphone and Urethane
Earloop (1 Wire)
†
BDN6664A Beige
BDN6665A† *Beige
BDN6726A Black
BDN6727A* Black
Earpiece Assembly (receive
only) with Volume Control and
Urethane Earloop (1 Wire)
BDN6666A† Beige
BDN6728A Black
Audio Accessories
BDN6781A Pellet Style Earpiece
BDN6719A Flexible Ear Receiver
RMN4056A
NMN6193B
BDN6667A
Earpiece Assembly with Microphone and Push-To-Talk
Combined (2 Wire)
BDN6667A† Beige
BDN6669A†* Beige
BDN6729A Black
BDN6731A* Black
Earpiece Assembly with Microphone
and Push-To-Talk Separate (3 Wire)
BDN6668A† Beige
BDN6670A†* Beige
BDN6730A Black
BDN6668A
BDN6732A* Black
BDN6676D† 3.5mm Jack Adapter with Quick Disconnect
Latch
* Extra Loud Earphone (exceeds OSHA limits)
†
FM Approved
00&9000/MT2000
Audio Accessories
Surveillance Kit
Replacement Accessories
5080369E38 Standard Earpiece
5080369E39
Assembly, includes earphone, earloop
and eartip, beige
5080370E90 Standard Earpiece
Assembly includes earphone, earloop
and eartip, black
5080369E39 Extra Loud Assembly,
5080370E92
includes earphone, earloop and eartip, beige
5080370E91 Extra Loud Earpiece Assembly,
includes earphone, earloop and eartip, black
5080369E40 Plastic Urethane Earloop, beige
5080370E92 Plastic Urethane Earloop, black
5080369E41 Wire Earloop
5080371E69 Small Rubber Eartip, beige
5080369E41
5080371E71 Small Rubber Eartip, black
5080371E73 Standard Rubber Eartip, beige
5080371E75 Standard Rubber
Eartip, black
Completely Discrete
Earpiece
Remain discretely in touch with
this miniaturized receiver. All
messages received through the
RLN4922A
user’s two-way radio are
inductively relayed to the wireless earpiece in the user’s ear.
Inductive neckloop is easily hidden under the user’s clothing for
covert operations. Neckloop attaches to the user’s Motorola
Surveillance Kit providing completely discrete two-way
communications. Security operatives, public safety officials, and
private investigators can communicate with ease without any
visible equipment. Small as it is, it offers a full range of audio
functions including automatic squelch, automatic gain control
and noise filtering. Must be used in conjunction with a
Motorola Surveillance Kit. Just remove the earpiece on any
standard 2 or 3 wire surveillance kit and plug in the
neckloop for completely discrete communication.
RLN4922A Completely Discrete Earpiece Kit; includes wireless
earpiece, inductive neckloop, 6 spare batteries and 5 spare ear
wax guards
RLN4919A Ear Wax Guards, 5 per pack
RNN4005A 1.4V Battery, 6 per pack
Noise Kits
Lightweight translucent tube attaches to
Motorola surveillance accessories.
Clothing clip prevents the accessory from
being pulled from the ear due to body
movement or head rotation.
NTN8370A Extreme Noise Kit, includes 2
foam earplugs for loud environments,
provides 24dB noise protection
NTN8371A Low Noise Kit, includes rubber eartip for
low noise environments
5080384F72 Replacement Foam
Plugs; pack of 50
(for use with NTN8370A)
Clear Comfortable Earpiece
The clear comfortable earpiece forms
to the inside of your ear and is perfect
for low noise environments.
Compatible with the NTN8371A,
clear acoustic tube assembly, and
most surveillance kits (1, 2 and 3
wire). This earpiece is made of easyto-clean chemically inert,
hypoallergenic material.
There are 3 items needed to make
this product work:
1. Clear Comfortable Earpiece
2. Clear Acoustic Tube
Assembly (NTN8371A)
3. Surveillance Kits
RLN4760A Small Custom Earpiece, right ear
RLN4763A Small Custom Earpiece, left ear
RLN4761A Medium Custom Earpiece, right ear
RLN4764A Medium Custom Earpiece, left ear
RLN4762A Large Custom Earpiece, right ear
RLN4765A Large Custom Earpiece, left ear
Ear Microphone System (EMS)
This compact unit picks up the voice through bone vibrations
in the ear canal. The miniature earpiece leaves the hands free
and face unobscured when worn by rescue and hazard
protection personnel, who still retain the ability for direct
hearing and speaking. For personnel required to wear
breathing apparatus, communications with protective masks
are as clear as communications without.
And its high speech clarity under
noisy environments makes it ideal for
high noise environments. Available
in PTT or Voice Activated (VOX).
Interface Module needs to be
ordered separately for EMS to
work
BDN6677A† Ear Microphone for Standard
Noise Levels
BDN6641A
(up to 95dB, black)
Shown with interface module
BDN6678A† Ear Microphone for
Standard Noise Levels
(up to 95dB, beige)
MOTOROL A
BDN6641A† Ear Microphone for High
Noise Levels (up to 105dB)
†
FM APPROVED
NTN8370A
ORIGINAL
http://Accesssecure.mot.com/Accesspoint
10
[ HT1000/JT1000/MTX80
Interface Module For EMS
CommPort: Integrated
Microphone/Receiver System
BDN6708B† Push-To-Talk Interface Module
BDN6671B† Push-To-Talk or Voice-Activated
Interface Module
†FM APPROVED
Optional Accessories For EMS
0180358B38† Remote Push-To-Talk
Ring Switch
0180300E83 Remote Push-To-Talk
Body Switch
0180300E25 Earguard with Adjustable
Loop; secures ear mic in ear
0180358B32 Earholder, black size
small; secures ear mic in ear
0180358B33 Earholder, black, size
medium; secures ear mic in ear
0180358B34 Earholder, black, size large;
secures ear mic in ear
0180358B35 Earholder, clear, size small;
secures ear mic in ear
0180358B36 Earholder, clear, size
medium; secures ear mic in ear
0180358B37 Earholder, clear, size
large; secures ear mic in ear
4280369E44 Replaceable Belt Clip
with Screws
5080358B28 Eartips, black, size medium
(10 per pack)
5080358B29 Eartips, black, size large
(10 per pack)
5080358B30 Eartips, beige, size medium
(10 per pack)
5080358B31 Eartips, beige, size large
(10 per pack)
BDN6708B
0180358B38
0180300E25
0180358B33
Flexible Ear Receiver
BDN6719A Ear Receiver with
3.5 mm Threaded Plug, requires
adapter BDN6676D unless being
used with speaker microphone
BDN6719A
Pellet
Style Earpieces
BDN6780A
BDN6780A Single Earbud with
Microphone and Push-To-Talk, requires
adapter BDN6676D, unless being used
with speaker microphone
BDN6781A Single Earbud, receive only;
requires adapter BDN6676D unless being
used w/speaker microphone
CommPort system contains a miniature
microphone and receiver, and connects to your
two-way radio, making it possible to hear and
speak under the most adverse conditions.
NTN1624A Integrated Ear Microphone/Receiver
System w/Palm PTT (includes
BDN6676D 3.5mm Jack Adapter)
NTN1625A Integrated Ear
Microphone/Receiver System
(includes BDN6676D 3.5mm
Jack Adapter)
NKN6510A Replacement Cable for
NTN1624
NKN6508A Replacement Cable for NTN1625
NTN8821A CommPort Maintenance Kit,
Includes Replacement Ear Tubes (Quantity 10),
Windscreens (Quantity 2) and Microphone Seal Strips
(Quantity 10)
NTN8986A Adhesive Pads (Quantity 90) for secure
attachment to ear
NTN8988A Ear Straps (Quantity 10), for secure
attachment to ear
4285838B01 Replacement Collar Clip
4202006A01 Replacement Back Cover Clip
Lightweight Headsets
Lightweight headsets allow for high clarity, hands-free,
discrete two-way communication, while adding comfort
necessary for extended wear in moderate noise
environments. Requires BDN6676D Audio Adapter.
NMN6245A† Single Muff Lightweight Headset with In-line
Push-To-Talk Switch (requires BDN6676D adapter)
NMN6246B† Ultralite Headset with Boom Microphone and Inline Push-To-Talk Switch; ear bud style receiver (requires
BDN6676B adapter)
NMN1020A† Lightweight Headset with Boom Microphone to
be worn on a helmet or safety glasses. Includes NKN6498A
adapter cable. Requires BDN6676D adapter. FM approved.
NKN6498A† Headset Adapter Cable for use with NMN1020A
5080574E02 Foam Earpads for use with NMN6245A,
10 per pack
†
FM Approved
O R D E R TO D AY !
1-800-422-4210
U.S. Federal Government Customers Call 1-800-826-1913
11
NTN1624A
00&9000/MT2000
Audio Accessories
Medium Weight Headsets
Medium Weight Headsets offer high-clarity sound with the
additional hearing protection necessary for providing
consistent, clear two-way radio communications in harsh,
noisy situations.
NMN6258A† Medium Weight Headset, over the head with InLine PTT, Noise Reduction Rating = 24dB
NMN6259A† Medium Weight Headset, behind
the head with In-Line PTT, Noise Reduction
Rating = 24dB
RMN4051A Hardhat Mount Headset mounts easily to hardhats
with slots and provides 22dB of noise reduction; requires
RKN4095A adapter cable, hardhat not included
RKN4095A Radio Adapter Cable with IN-Line PTT for use with
RMN4051A
NMN6258A
RMN4053A
RKN4095A
Tactical Medium Weight Headsets
Same high-clarity sound and additional hearing protection as
our standard medium weight headsets while including two
microphones on the outside of each earcup which reproduces
the ambient sound back into the headset. Harmful sounds are
suppressed to a safe level and low sounds are amplified up to
5 times but never more than 82dB. Includes on/off volume
control on ear cups.
RMN4052A Tactical Headband Style Headset, grey;
provides 24dB of noise reduction and requires RKN4095A
adapter cable
RMN4053A Tactical Hardhat Mount Headset mounts easily to
hardhats with slots; provides 22dB of noise reduction and
requires RKN4095A adapter cable, hardhat not included
RKN4095A Radio Adapter Cable with IN-Line PTT for use with
RMN4051A and RMN4053A
BDN6645A
Heavyduty Headsets
Heavyduty headsets include noise-cancelling boom
microphones and can be worn with or without a hardhat.
Headsets are for use in noise levels up to 125 dB. The PushTo-Talk switch is located on the earcup. The VOX module is
contained within the headset on voice activated units.
Heavyduty headsets require radio adapter cable
BDN6673B, to be ordered separately.
BDN6645A† Push-To-Talk Headset with Boom Microphone;
requires adapter cable BDN6673B; noise reduction
rating=24dB
BDN6635B† Voice-activated Headset with Boom Microphone;
requires adapter cable BDN6673B; noise reduction
rating=24dB
BDN6636B† Voice-activated Headset with Throat Microphone;
requires adapter cable BDN6673B; noise reduction
rating=24dB
BDN6673B† Radio Adapter Cable
†
BDN6635B
RMN4052A
MOTOROL A
ORIGINAL
BDN6636B
FM Approved
http://AccessSecure.mot.com/Accesspoint
12
[ HT1000/JT1000/MTX80
Carrying Cases
Carrying Case Accessories
A variety of carrying accessories
are available for your comfort and
convenience. The carrying cases
are available in sizes designed to
fit your radio and battery and
permit audio to be heard clearly.
T-Strap
NTN7782A T-Strap for leather
Carry Cases
NTN7376A T-S trap for nylon
carry cases
Belt Loops
NTN8039B 2.5" High Activity Swivel
Belt Loop
NTN8040B 3.0" High Activity Swivel
Belt Loop
Standard Belt Loop
Carrying Cases
NTN7238A Leather Carry Case
with Belt Loop and T-Strap for use
with high capacity battery
NTN7239A Leather Carry Case
with Belt Loop and T-Strap for use
with ultra-high capacity battery
NDN4018B DTMF Leather Carry
Case with Belt Loop for use with high
and ultra-high capacity batteries
NTN7247A Nylon Carry Case with
Belt Loop and Strap for use with high
and ultra-high capacity batteries
NTN7247A
13
NTN8038A
NTN8036A
High Activity Swivel
Carrying Cases
The following carrying cases have a
high activity swivel "D" button and
belt loop. To remove case from belt
loop, rotate case 180 degrees and
slide case upward, out of the holder.
Case stays on belt more securely in
high activity applications versus
standard swivel cases while allowing
the radio to swing freely with body
movements.
NTN8035B Leather Carry Case with
2.5" High Activity Swivel Belt Loop
and T-Strap for use with high
capacity battery
NTN8037B Leather Carry Case with
3.0" High Activity Swivel Belt Loop
and T-Strap for use with high
capacity battery
NTN8036B Leather Carry Case with
2.5" High Activity Swivel Belt Loop
and T-Strap for use with ultra-high
capacity battery
NTN8038B Leather Carry Case with
2.5" High Activity Swivel Belt Loop
and T-Strap for use with ultra-high
capacity battery
NDN4017B Leather Carry Case with
3.0" High Activity Swivel Belt Loop
and T-Strap for use with high and
ultra-high capacity battery
Belt
4200865599
3.0" Wide Black Belt
420086599
Carrying Strap
NTN5243A
Shoulder Carry Strap, allows easy
carrying of radio in a case when not
wearing a belt
NTN5243A
00&9000/MT2000
Carrying Accessories
Chest Pack
Carry the radio mounted on chest with
adjustable straps over shoulders and
around waist.
HLN6602A Universal Chest Pack with
Radio Holder, Pen Holder, and Velcro
Secured Pouch
1505596Z02 Replacement Strap for
HLN6602A
Swiveller
TDN9684A Swiveller, includes clip
button, holster and belt
Swiveller Replacement
Accessories
TDN9690A Clip button, mounts
on battery
TDN9688A Holster, compatible
with all buttons
TDN9687A Belt, 2" nylon
TDN9684A
HLN6602A
Break-A-Way Chest Pack
All of the same features as the original chest pack
(HLN6602A) plus break-a-way tabs that allow the
entire pack to be pulled off with
approximately 10 lbs. of pressure.
Perfect for railroads, manufacturing
locations, construction sites and anywhere
safety is a concern.
RLN4570A Break-A-Way Chest Pack
RLN4570A
TDN9687A
Portable Radio Hanger
The portable radio hanger slides over and
hangs from the door panel in a vehicle. The
radio’s belt clip slides onto the portable
hanger allowing convenient, easy mounting.
Two sizes are available to fit door panels.
TDN9327A Portable Radio Hanger for door
panels up to 2.75"
TDN9373A Portable Radio Hanger for door
panels up to 3.25"
RadioPAK™
RLN4815A Universal RadioPAK™ with
Radio Holder. Worn around waist with
adjustable belt. Includes attached 6"
by 8" zippered pouch for other job
necessities.
4280384F89 Universal RadioPAK™
belt lengthener; fits waists larger
than 40"
TDN9327A
RLN4815A
http://AccessSecure.mot.com/Accesspoint
14
[ HT1000/JT1000/MTX80
Nickel Cadmium
Part Number:
Capacity
Avg. mAh:
Part Number:
Capacity
Avg. mAh:
Part Number:
Capacity
Avg. mAh:
FM Rating:*
Part Number:
Capacity
Avg. mAh:
FM Rating:*
Part Number:
Capacity
Avg. mAh:
FM Rating:*
Nickel Metal Hydride
NTN7143CR
High
1200
NTN7144AR
Ultra High
1400
NTN7146AR
High
1200
IS & NI
NTN7147AR
Ultra High
1400
IS & NI
NTN7149BR
Ultra High
1400
CSA
Part Number:
Avg. mAh:
FM Rating:*
Part Number:
Capacity
Avg. mAh:
FM Rating:*
Part Number:
Capacity
Avg. mAh:
FM Rating:*
NTN7150AR
1200
MSHA
NTN7341AR
Ultra High
1400
IS & NI
NTN7372AR
Ultra High
1300
IS & NI
FM Rating:*
IS = Intrinsically Safe
NI = Non Incendiary CSA-MSHA
Part Number:
Capacity
Avg. mAh:
FM Rating:
WPNN4013A
Ultra High
2000
(NA)
Part Number:
Avg. mAh:
FM Rating:
WPNN4037A
1900
IS & NI
Alkaline
Part Number:
Volts:
NTN8122AR
9V, 12 Cell Battery
Pack
Vehicular Battery
Eliminator
The battery eliminator
saves useful battery life
by drawing power from a
vehicle’s battery. Simply
replace the portable
battery with the battery
eliminator and plug in the
cigarette lighter adapter.
RLN4335A Battery
Eliminator, vehicular
WPNN4013AR
NTN7143CR
NTN7372AR
NTN7144AR
RLN4335A
15
00&9000/MT2000
Batteries and Chargers
Chargers
Multiple Unit Charger (MUC)
Single unit chargers are available in either desktop or
compact styles for small system users. Multiple unit
chargers can be wall or rack mounted and are ideal for
multi-shift operations. All chargers are specifically
designed to meet the requirements of batteries
manufactured by Motorola. All chargers listed are
rapid rate and will fully charge your battery in less
than 3 hours.
Multi-unit chargers offer six pockets that can be used
to rapid charge 1 to 6 batteries simultaneously. The
batteries can be charged with the radios or separately.
They will rapid rate charge both NiCd and NiMH
batteries.
NTN1177C Six Pocket, rapid rate110V
NTN1178C Six Pocket, rapid rate, 220V (supplied with 2
prong cord)
NTN1179C Six Pocket, rapid rate, 240V (supplied with 3
flat prong cord)
MUC Accessories
NLN7967A Wall Mount
NTN1177C
NTN1168A
Motorola Conditioning
Charger (MCC)
Single Unit Desktop Chargers—
Rapid Rate
The desktop charger has the power supply built into the
base unit and will charge both NiCd and NiMH batteries.
NTN1168A Rapid Rate Desktop Charger, 110V
NTN1169A Rapid Rate Desktop Charger, 220V
(supplied with 2 prong cord)
NTN1170A Rapid Rate Desktop Charger, 240v
(supplied with 3 flat prong cord)
Single Unit Compact Bi-Chemistry
Chargers—Rapid Rate
The bi-chem charger has the power supply built into the
line cord giving the user a smaller base unit for
easier storage. It also utilizes an enhanced charging
algorithm that will help maximize the life of your
batteries. It will rapid rate charge both NiCd and
NiMH batteries.
RPX4747A Compact Bi-Chem Charger, 110V
RPX4748A Compact Bi-Chem Charger, 230V Euro plug
RPX4749A Compact Bi-Chem Charger, 230V UK plug
O R D E R TO D AY !
1-800-422-4210
U.S. Federal Government Customers Call 1-800-826-1913
The MCC will help extend battery life and enhance
battery operation. It will safely condition and charge your
specified nickel cadmium (NiCd) and nickel metal
hydride (NiMH) batteries in approximately an hour.
WPLN4090AR MCC Kit, 110V AC; includes both base
unit and 7V adapter
WPLN4091AR MCC Kit, 220V AC; includes both base
unit and 7V adapter
WPPN4002AR 110V AC Base Charge Unit Only
(order adapter plate separately)
WPPN4006AR 220V AC Base Charge
Unit Only
(order adapter plate
separately)
WPPN4065AR Multi-Unit
Conditioning Charger Four
Station Base 110V (order adapter
WPPN4002AR
plate separately)
Shown
With Optional
WPPN4004AR 7 Volt
Cigarette Lighter Adapter
Adapter Only
3080384G15 Cigarette Lighter
MOTOROL A
Adapter Cord;
MCC multi-unit conditioning charger
ORIGINAL
http://Accesssecure.mot.com/Accesspoint
16
[HT1000/JT1000/MTX80
Battery Optimizing System (BOS)
WPLN4079AR
Battery Maintenance SystemPlus (BMSPlus)
Increase the useful life of your batteries.
Using interchangeable battery adapters (sold separately), the
BMSPlus is capable of charging and discharging, analyzing,
conditioning and cycle test on batteries; tracking battery
voltage and capacity (mAh).
No other battery analyzer matches the speed,
effectiveness, accuracy, versatility and ease-of-use of the
Battery Optimizing System. Best of all, the Battery
Optimizing System helps lower your battery costs
because you will get the maximum performance possible
from each battery when it is maintained by the Battery
Optimizing System.
• Accommodates NiCd, NiMH, Li-Ion and SLA
• Impedance-test checks battery condition in six seconds
• Proprietary recondition cycle restores NiCd and NiMH
batteries
• Printer output for reports and labels, computer interface
• High power—programmable from l00mA to 2 amp
per station
• Interchangeable adapters accommodate all major
batteries
• Simple, intuitive user interface with keypad (adapter
sold separately)
WPLN4071AR Four Station, 110V AC, 50/60 Hz
WPLN4073AR Four Station, 230V AC, 50/60 Hz
The BMSPlus offers a 3 year warranty. Its easy-to-use
design supports hundreds of 2-way, cellular, and camcorder
batteries with printer port* (Serial-RS-232C port – uses
female 9-pin to male 25-pin cable).
WPLN4079AR Six Station, 110V AC, 50/60 Hz
WPLN4080AR Six Station, 230V AC, 50/60 Hz
*Compatible with the STAR Micronics SP200 series printers,
available from any STAR Micronics distributor, and other printers with
STAR emulation.
BMSPlus Adapter
TDN9435C Adapter Compatible
with NiCd Batteries Only
CDN6364A Adapter
Compatible with Both NiCd and
NiMH Batteries
WPLN4071AR
TDN9435C
BOS Adapter
RL-72403 Standard Adapter
O R D E R TO D AY !
1-800-422-4210
17
U.S. Federal Government Customers Call 1-800-826-1913
00&9000/MT2000
Chargers, Antennas and Manuals
Injection molded for rugged environments. Each
antenna is tested and tuned to give maximum power
and performance.
Flexible Whip Antennas
Antenna has a one-piece finish and steel core for optimal
strength and better radiation characteristics. Provides more
comfort when radio is worn on the belt.
8505241U05 Flexible Whip, 403-520 MHz, 6"
8505241U03 Flexible Whip, 806-869 MHz, 7"
8505241U04 Flexible Whip, 896-941 MHz, 7"
Helical Antennas
Helical antennas are sturdy and dependable for years of
failsafe communication. Each antenna is designed and built
to quality standards. The skirt at the base of the connector
helps to seal out damaging elements. Connector is made of
plated brass material for long life.
8505644V01 Helical, 136-151 MHz, 6"
8505644V02 Helical, 151-162 MHz, 6"
8505644V03 Helical, 162-174 MHz, 6"
8505644V04 Helical, 403-435 MHz, 3"
8505644V05 Helical, 435-470 MHz, 3"
8505644V06 Helical, 470-520 MHz, 3"
Miscellaneous Accessories
Public Safety Tilt Switch
An external emergency switch that is activated when the unit
is tilted at a greater than 60 degree angle. Delay times are
factory programmed for 8 seconds and are not field
programmable. The emergency feature must be
programmed into the radio to enable the tilt switch option.
FM approved. Not compatible with the JT1000.
NTN7660A Public Safety Tilt Switch
Option Boards
NTN8313A Analog Voice Scrambler Advantage Board, for
use with HT1000 only. NOT APPROVED for installation in
FM approved models.
Service Manuals
6881200C15 HT1000/JT1000/MT2000 & MTX8000/9000
Radio Theory
6881200C40 HT1000/JT1000 & MT2000 Service Manual
6881200C25 MTX8000/9000 Service Manual
6881079C50 HT1000 Operator’s Manual
6881078C45 JT1000 Operator’s Manual
6881076C65 MT2000 Operator’s Manual
6881072C10 MTX8000/9000 B3 Operator’s Manual
6881072C40 MTX8000/9000 B5/B7 Operator’s Manual
Dipole Antennas
Dipole molded antennas are
injection molded in lasting
polyurethane. The wide skirt at the
bottom of the connector protects
against damaging environmental
elements. The dipole antenna is ideal
when strong and solid signal clarity
is demanded.
NAF4000B Dipole, 806-869 MHz, 8"
8505884R02 Dipole, 896-941 MHz, 8"
8505644V04
8505241U05
8505241U06
Wideband Antenna
Wideband antenna is ideal when radio is
used in different frequencies since one
antenna will cover all ranges.
8505518V01 Wideband,
136-174 MHz, 6"
8505644V01
Stubby Antenna
8505644V03
This quarterwave stubby antenna is ideal
when radio is worn on the belt because
the short antenna is non-obtrusive. This is
a broad band and antenna that can be
used for both 800MHz and 900MHz
applications.
8505241U06 Stubby, 806-941 MHz, 4"
MOTOROL A
ORIGINAL
NAF4000B
8505884R02
http://AccessSecure.mot.com/Accesspoint
18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement