Directed Electronics AutoCommand 25622 Installation manual

Directed Electronics AutoCommand 25622 Installation manual
OEM SERIES
Remote Control Car Starter Installation Manual for Models 28624T and 28628
www.designtech-intl.com • www.directed.com • 800-876-0800
PLEASE READ COMPLETELY BEFORE BEGINNING
Congratulations on your purchase of the AutoCommand® OEM Series Remote Car Starter. The AutoCommand® OEM Series Remote Car Starter system allows you to start the car
by remote control from the comfort of your home or office in order to cool it down in the summer or heat it up in the winter.
AutoCommand® OEM Series is for automatic transmission/fuel injected vehicles only. It is an extremely sophisticated system with multiple built-in safety and security
features.
AutoCommand ® OEM Series Car Starter:
• Will start your car by remote control, and run the heater, defroster, or
air conditioner to warm up or cool down the car.
• Is designed to start the car if it is in park, and only if the hood is
closed.
• Has Lock, Unlock and Trunk keyless entry features.
• Will shut off if the brake pedal is pushed, the hood is opened, or the
transmission is shifted out of park - unless the key is in the ignition and
in the “run” position.
• Allows you to remove the key while leaving the car running with the
doors locked for up to 10 or 15 minutes utilizing the Quick Stop™ Option. (See Separate User Tip Sheet)
• Will attempt to start the car for up to six seconds, but no longer (to
avoid damage to the starter motor). Should the car not start, or if it
stalls after starting, the remote starter will make two further attempts
to start it.
• Starts the car automatically whenever the temperature drops below
0°F (-18°C), or if the battery voltage drops below 11 volts when the
Cold Start™ Option is used. (See Separate User Tip Sheet)
• Has alarm functions including starter kill which becomes active when
the doors are locked with the remote control.
• Has the “Daily Start™” feature which allows the vehicle to be started
at the same time the following day. (See Separate User Tip Sheet)
• Will not let the car be driven without the key in the ignition.
• Is quality engineered and microprocessor controlled to provide many
years of reliable use.
• Shuts itself off automatically after 10 or 15 minutes (programmable) if
you forget to come out to your car.
Tools required to install the AutoCommand® OEM Series Unit:
Wire Cutters/Strippers
Soldering Iron
Pliers
• Comes with a Limited Lifetime Warranty.
Wiring Diagram
Electrical Tape
Screwdriver
Drill with1/4”and 5/16”
drill bits
Test meter
We highly recommend that all connections be soldered for reliability.
Parts List included with the AutoCommand® OEM Series Unit:
Remote Starter
Receiver Module
Antenna
Control Harness
(10 position)
2 Relays with relay harnesses
(Model 28628 only)
Transmitter
Siren (Model 28628 only)
6 Power and Ignition wires
Shock Sensor
(Model 28628 only)
Following parts included in plastic baggy
Alchohol
Pad
Ring Terminal
Alcohol Pad
Green 30 A Fuse
Hood Pin Switch Set
On/Off Control Switch
2 Cable Ties
Plug-In LED
3 Pin Door Harness
2 Protected by
DesignTech Labels
© 2005 Directed Electronics, Inc.
Yellow Butt Connector
* For free vehicle specific wire information, consult
our website at www.designtech-intl.com
Warning Label
v5.3 J2428
Note: Failure to properly install the fuse holder and 30 amp fuse to the PINK wire
to the battery voids all product warranties.
On cars with airbags, you may notice bright yellow tubes or harnesses
marked SRS (Supplemental Restraint System) underneath the steering
column area. DO NOT tamper with these wires in any way, to prevent
personal injury and/or damage to the air bag system.
Ignition Key Diagram for Steps 4-7
The vehicle’s wires are found coming off of the key
switch. Remove the panel under the steering column to
access these wires.
Battery gases are explosive.
Do not smoke while working near the car’s battery.
Note: Some installers connect a battery charger to the vehicle’s battery during
installation. This is fine, but it must be removed before running the vehicle under
remote starter control.
4. Blue Wire (14 AWG) – Ignition 1
Connect the BLUE wire to the ignition 1 wire of your vehicle. This wire will measure
+12 Volts on the test meter in the “run” and “start” position, and is off in the “lock/
off” and “accessory” positions.
All General Motors (GM), rear wheel drive vehicles built prior to 1995
with automatic transmissions and Dodge Dakota trucks (4 cylinder
engines only) with automatic transmissions built prior to 1996 have a
MECHANICAL TYPE of NEUTRAL SAFETY SWITCH. See important
warning on the last page of these instructions.
5. Green (14 AWG) – Ignition 2
Connect the GREEN wire to the Ignition 2 wire in the vehicle. The Ignition 2 wire can
function in several different ways in your vehicle. It is important to understand how
it works. The Ignition 2 wire will usually measure +12 Volts in the “run” position
and is off (ground) in the “lock/off” and “accessory” positions. In certain vehicles,
it may also show +12 Volts in the “Start” position or Ignition 2 may turn OFF during
“Crank” and turn back ON after the starter disengages. Carefully note the function
of the Ignition 2 wire. If the Ignition 2 turns OFF during “Crank”, set Option #4
(section 24). If Ignition 2 stays ON during “Crank,” no options need to be changed.
When running the wires through the car’s firewall, be sure to protect
them from sharp metal edges and from hot surfaces on and around the
engine.
INSTALLATION INSTRUCTIONS
6. White Wire (14 AWG) – Accessory
1. Before You Start
Connect the WHITE wire to the accessory wire which is +12 Volts in the “run” and
“accessory” position, but off in the “start” and “off” positions. In GM vehicles,
connect the white wire to the orange wire that is hot in “run” only.
Take time to read through the whole installation manual before beginning.
Always leave a window open to avoid locking your keys in your car.
IMPORTANT: After having read the entire manual, start the installation by
putting the yellow WARNING STICKER in the engine compartment. Choose
a surface that is clean and readily visible when the hood is open.
7. Yellow (14 AWG) – Starter
Connect the YELLOW wire to the starter wire. This wire will measure +12 Volts on
the test meter in the “start” position only.
Note: Most Nissan vehicles have two starter wires. Connect both starter wires of
the vehicle to the YELLOW start wire of the remote starter.
WARNING
This car is equipped with a remote control starting device.
Disable before working on car!
8A. Plug-In On/0ff Switch
AVERTISSEMENT
Ce véhicule est équipé d’un systéme de démarrage a distance. Mettez-le
hors fonction avant d’eflectuer toute opération d’entretien ou de réparation!
Mount the control switch so that it is easily accessible and so that the “ON”
position is facing upward. Make sure there is enough clearance behind the
mounted switch for the wire connections. Do not let the switch wires touch ground.
Do not plug the switch into the unit until it is mounted first. Connection of this
switch is mandatory. Use a 1/4" drill-bit for the mounting hole.
POWER & IGNITION HARNESS
The remote starter module will be installed under the dash once all wiring has been
completed. Do not mount the module at this time! You will need to check
the red diagnostic LED light as the installation progresses. Locate (or drill)
a hole in the firewall to run the PURPLE and GREEN wires of the Control Harness
and the PINK wire of the Power Harness into the engine compartment. The
remaining short wires stay in the passenger area. Leave about a foot of the wire
harness under the dash for ease of working and visual access to the diagnostic
light.
Plug the ON/OFF control switch into the module just to the right of the power wires.
Turn the switch on.
8B. Plug-In LED Light
Drill a 5/16" hole in to the dash or panel to mount the LED light and plug the LED
light plug into the red connector. Mounting the LED light is not mandatory but the
LED light is used for alarm status, troubleshooting and programming options.
The Installation Information section of www.designtech-intl.com is available 24
hours/day to provide you with free, up-to-date vehicle wiring information for your
particular vehicle after you log in.
CONTROL HARNESS
Note: Always connect the PINK and BLACK wires before connecting any of the
other wires. Do not insert the fuse until Step 11.
ALL WIRES ARE THE SMALLER 18 AWG SIZE
2. Black Wire (16 AWG) – Ground
The hood pin switch MUST be installed with the remote
starter. It prevents operation of the remote starter when
the hood is open and is used to initialize the unit.
Connect the PURPLE wire to the hood pin switch using
the red connector.
9. Purple Wire – Hood Pin Switch – Control Harness
Connect the BLACK wire to a very good, clean chassis ground in the driver’s kick
panel area. Use the small ring terminal. (The thin metal bracing around or beneath
the dash board is not always adequate.)
3. Pink Wire (12 AWG) – Power (+12 Volts)
Note: If you already have a hood pin switch which is
being used by a car alarm system, you may share the
wiring – but be sure to diode isolate each wire going to
the hood pin switch with the bands of diodes pointing
towards the pin switch as shown at right.
Connect the ring terminal at the end of the short PINK wire to the +12 Volt terminal
of the battery. Run the long PINK wire through the firewall of your vehicle. Join the
remaining ends of the power wire together by soldering them. Tape with electrical
tape to leave no exposed wires. Alternatively, you may wish to use the yellow butt
connector, but we recommend soldering. Wait to insert the 30 amp green fuse into
the holder until Step 11. As the power is first applied to the unit the red diagnostic
LED light will blink once.
v5.3 J2428
2
To Alarm
To Remote Starter
How to share a hood pin
switch with an alarm
© 2005 Directed Electronics, Inc.
10. Orange Wire – Brake Shut-off – Control Harness
E. Turn the On/Off control switch back to the “ON” position
F. Start the car with the key and let it get to a normal idle. Do not press on the gas
pedal.
G. Push the red “code learn” button for a second.
H. Watch the red LED light. It will come on after 3 or 4 seconds, indicating that the
tach idle rate has been learned.
I. Watch that the LED light remains on as the vehicle is running and turns off
when you rev the engine RPMs to twice the idle rate. The LED light must go out
when you rev the engine to about twice the idle rate to confirm correct tach
learning.
J. Turn the key to the “Lock/Off” position.
K. Turn the ON/OFF control switch off and the red LED light will go out. You are
now finished.
Connect the ORANGE wire to the brake wire which receives +12 Volts when the
brake pedal is depressed. This wire must be connected. It arms a critical
safety feature which disables the remote starter when the brake pedal is depressed.
Note: In some cars, the ignition must be in the “on” position to test the power in the
brake wire.
Note: If the Ignition 1 and Ignition 2 wires come on whenever the brake is depressed
and the hood is open this just means you need to initialize the unit in section 11.
11. Initializing the Remote Starter
BEFORE THE UNIT WILL DO ANYTHING FOR THE FIRST TIME, YOU MUST
INITIALIZE THE REMOTE STARTER
A. Insert the 30 amp fuse into the fuse holder on the large PINK wire.
B. Turn the control switch on.
C. The remote starter requires the installer to open the hood and then press and
hold the brake pedal. Note: The ignition/dash lights will come on if the unit
is not initialized.
D. While depressing the brake (with the engine off and the hood open) turn the
ignition key to the “RUN” (not “start”) position.
E. Put the car in “DRIVE” from the “PARK” position.
F. Put the car back in “PARK” and release the brake.
G. Turn the key off and remove the key.
Note: Once these steps are complete – you cannot use the LED to confirm tach
again. You can however repeat the above steps to learn tach over again at any time.
OPTIONAL STEPS
13. Yellow Wire – Headlights/Parking Lights – Control
Harness
Connection of the YELLOW wire allows you to activate the low beam headlights
or parking lights for remote start and lock status. After the remote starter has
started the car, the lights will remain on until the remote starter shuts off after 10
minutes, or when the brake pedal is pushed, or when the car is put into gear. This
is a relay +12 Volts output. Connect the YELLOW wire to the wire that has power
when the lights are on.
Note: Confirm initialization by turning the ON/OFF control switch “OFF” and then
“ON”. The red LED light on the remote start module will flash once immediately as
the switch is flipped from the “OFF” to the “ON” position.
If the red LED light did not flash when the control switch was turned “ON” REPEAT
STEPS A THROUGH G. See the colored Trouble Shooting Sheets if necessary.
14. Blue – Horn/Siren – Control Harness
12A. Green Wire – Tach Input – Control Harness
The BLUE wire signals the horn to honk (or siren to chirp) once each time the remote
starter starts the vehicle and each time the locks are locked or unlocked. Connect
the blue wire to the factory horn wire which is often found running down the steering
column. It will normally show +12 Volts at rest and the voltage will disappear when
the horn is honked. This is
a 400 mA transistor
Positive Horn/Siren Relay
ground output which
MUST drive a relay if
using a siren or
positively triggered
horn. Option #11 (section
24) must be changed when
using a siren.
The remote starter has two ways of monitoring the car during the starting process.
Both ways will ensure a clean, accurate start. Read about both methods before
deciding which one to use. Normally you should try the “No Tach™”
method first.
“No Tach™” Starting
This starting method does not require the connection of the GREEN tach wire. This
method will start the car by reading the car’s voltage before attempting to start, and
then looking for a voltage increase when the alternator kicks in. This feature
automatically takes into account voltage, temperature, and the time since the
vehicle was last run. The “No-Tach™”” starting is preset at the factory and you can
skip step 12B if you would like to use it. Note that if the vehicle is hard to start, set
Option #3 (section 24) for “extended crank.”
Tachometer sensing
If the vehicle is generally hard to start (i.e. requiring a cranking time of more than
1 second) you will get more accurate starting with the tachometer sensing starting
method. This method starts the car by reading the engine speed (tach) information
from a wire under the hood. If you choose tachometer sensing, connect the GREEN
(18 awg) wire to the car’s tach wire under the hood (normally the negative side of the
coil or tach output of coil pack). After you have connected the GREEN wire, you
need to teach the remote starter the vehicle’s tach rate at idle. Proceed to step 12B.
15. Brown/White – Alarm Disable/Starter Kill – Control
Harness
The BROWN/WHITE wire is Alarm Disable, which will give out a quick negative
pulse just before starting the vehicle. This wire can be used to turn off the factory
alarm system in vehicles which have them. In most vehicles, this wire is located
in the driver’s kick panel.
Using Option #19 (section 24) you can set this to Starter Kill. This option prevents
the vehicle from being started with the key when the alarm is armed. It is also
active whenever the vehicle is running under remote starter control to provide antigrind protection.
Note: You must have already initialized the remote starter from Step 11.
12B. Tach Rate Learning
Note: Only use if the tachometer sensing method is chosen.
Starter Kill Relay
A. Connect the GREEN wire to the car’s tach wire under the hood.
B. Turn the On/Off control switch to the “OFF” position. Wait 5 seconds for the red
LED light flashes to stop.
C. Program the unit to the tach mode by pushing the White “option” button once
and watching the red LED light flash. Now push the start button on the
transmitter for a second until you see the red LED light flash again. You are now
in TACH mode. (If the red LED light flashed twice or sometimes three times –
simply push the transmitter button again until you get only one flash).
D. Wait 5 seconds for the red LED light to flash 3 times.
© 2005 Directed Electronics, Inc.
Starter Wire
From Key
Switch
Starter Wire
To Starter
Motor
Cut
Remote Starter
Brown / White
Wire
87
86
87A
30
85
Tap into Blue
IGN1 Wire from
Remote Starter
Yellow Start Wire
From Remote Starter
3
v5.3 J2428
16. White/Black Wire – Ignition #3 – Control Harness
This BROWN wire can also control a relay for Dome Light activation. When Option
#20 (section 24) is changed, this BROWN wire causes the dome light to turn on for
25 seconds every time the doors are unlocked with the transmitter.
The WHITE/BLACK wire, is a ground output that acts just like the Ignition 1 or
Ignition 2 relay outputs (active in
the “run” and “crank” positions).
Ignition 3
This wire is a 400 mA negative
transistor output and MUST be
set up to power a relay (not
included). It can be used to power
the third ignition wire at the key
(necessary for most Ford vehicles).
White/Black Wire
From
Remote Starter
87
85
19. Red/White Wire – Door Pin Alarm Input – Control Harness
The RED/WHITE wire is the Door Pin Alarm Input. This wire will accept any input
that supplies a negative (ground) when activated. (Most door pins go to ground
when the door is open, +12 Volts when closed.)
To LARGE 12 Volt
Constant Wire
(Found in Ignition
Switch Wire
Harness)
87A
30
86
To Additional
Ignition Wire
(in vehicle)
Most Ford vehicles are positive door pins that switch to +12 Volts when opened, you
will need to reverse the polarity before connecting to this RED/WHITE wire. Change
Option #23 (section 24) Negative/Positive Door Pin Switch.
This is the wire that can also be used to bypass a passive vehicle anti-theft system
by hooking it up to the Universal Bypass Module. See the Factory Anti-Theft
System section at the end of these instructions.
The alarm is “Last door arming.” You should diode isolate the inputs of two or more
sensors on the same input wire.
If you choose not to use this alarm feature then permanently ground this
wire or program “No Alarm” Option #24 (section 24).
17A. Yellow and White – Keyless Entry Wires – 3 Wire Harness
The wires function as follows:
YELLOW
WHITE
Negative Trigger – Unlock
Negative Trigger – Lock
20. Red/Black Wire Diesel “wait to start” Control Harness
Positive Trigger – Lock
Positive Trigger – Unlock
This wire is only used in diesel vehicle applications – and is optional. This
wire can be hooked up to the “wait to start” light’s switched wire behind the dash.
If Option #9 (section 24) is set, this wire will feed information to the remote starter
as to when to crank the vehicle over. This wire is not polarity sensitive.
Determine the polarity of your door lock system by using a test meter. For NEGATIVE
locks (the lock wire sees a ground signal briefly as the electric locks are locked) –
connect the YELLOW wire to the Unlock wire and the WHITE wire to the Lock wire.
For POSITIVE locks (the lock wire sees a +12 volt signal briefly as the electric
locks are locked but does not see ground when they are inactive) connect the
YELLOW wire to the Lock wire and the WHITE wire to the Unlock wire.
REQUIRED FINAL STEPS
Note: You must have hooked up all required wires and completed Initialization
(Step 11) to proceed forward.
For REVERSING POLARITY (the lock wires sees a +12 volt signal briefly as the
electric locks are locked and sees a ground signal when they are inactive) follow
the diagram below:
Lock Relay
Vehicle Lock Wire
WARNING: Be prepared to apply the brake during this testing.
(Primary Switch Side)
(Actuator Side)
Cut
Cut
To 12 Volt
Constant
(15 Amp Fused)
White Wire
From
Remote Starter
3-pin Harness
87A
30
86
B. Place the vehicle in Park.
To 12 Volt
Constant
(15 Amp Fused)
Yellow Wire
From
Remote Starter
3-pin Harness
87
85
A. Close the hood and fully apply the emergency brake
Vehicle Unlock Wire
(Actuator Side)
(Primary Switch Side)
21. Trying the Unit Out
Reversing Polarity Door Locks
Unlock Relay
87
87A
30
85
C. Turn the On/Off switch off then on – the red LED light will flash once.
86
D. Once all the wiring is checked and is correct, press the Start button on the
transmitter.
Most VACUUM operated door lock systems require Option #18 (section 24) for Long
locks to be set.
E. The car should start and continue to run for ten minutes. Make sure that the
engine shuts down if the car is shifted out of park, the hood is opened, the brake
is pressed or the start button is pushed again. If the car does not start, see the
Code Learning section under Special Cases.
17B. Green Wire – Trunk Release – 3 Wire Harness
The GREEN wire is the Trunk Release output which gives out a transistor ground
output when the unlock button is held for 4 seconds. Again, this is a 400 mA
transistor ground output which MUST drive a relay (not included).
Negative Trunk Release
87
85
87A
30
86
Feed the antenna around under the dash and up the inside of the right or left
windshield post and over the top of the windshield. Clean the windshield with the
alcohol pad provided for maximum adhesion. Mount the last eight inches of the
antenna behind the rear view mirror. The more exposed the end of the antenna is, the
better the range performance. Now plug the end of the antenna into the remote
starter module. In most vehicles you will get better range performance if the
antenna is pointing vertically downward from the top of the windshield.
Positive Trunk Release
Ground (-)
Brown Wire
From
Remote Starter
22. The Antenna
To 12 Volt
Constant
(15 Amp Fused)
To 12 Volt
Constant
(15 Amp Fused)
Brown Wire
From
Remote Starter
87
85
87A
30
86
To Positive
Trunk Release
(in vehicle)
To Trunk Release
(in vehicle)
Note: The wiring section of the installation is now complete. Be sure to
cap all unused wires so as to prevent short circuits, and mount the module
securely under the dash. When tying up and mounting the unit, be sure to
avoid any moving parts (steering column, pedals) and sharp edges.
18. Brown Wire – Accessory Pulse/Dome Light – Control
Harness
The BROWN wire is the Accessory Pulse output which gives out a momentary,
transistor ground output 10 seconds after the vehicle is remotely started. This is
important in some vehicles to control the defroster or to control the GM R.A.P.
system. Again, this is a 400 mA transistor ground output which MUST
drive a relay (not included).
Negative Dome Light
23. Trouble Shooting with the Self Diagnostics
The remote starter contains a built in diagnostic routine that will indicate why the
unit started or why the unit turned off the car the last time that the unit was used.
To activate the diagnostic mode for why it turned off, simply turn the On/Off
control switch to the “OFF” position. In a few seconds, the red LED light on the
module will flash 1 to 12 times to identify the problem. See the chart on the next
page for an explanation of the flashes:
Positive Dome Light
(Most Ford Vehicles)
Ground (-)
Brown Wire
From
Remote Starter
87
85
87A
30
86
To 12 Volt
Constant
(15 Amp Fused)
To Negative
Door Pin
(in vehicle)
v5.3 J2428
To 12 Volt
Constant
(15 Amp Fused)
Brown Wire
From
Remote Starter
87
85
87A
30
1 flash
86
To Positive
Door Pin
(in vehicle)
4
10/15 minute time out. Unit should be fine. Make sure transmitter is
working properly.
© 2005 Directed Electronics, Inc.
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Normal
Normal
1 sec. alarm disarm pulse
Horn Pulsing
Chirp with Locks
Active
Normal
Normal
Normal
Normal
Short Locks
Alarm Disable
Accessary Pulse
N/A
N/A
Negative Door Pin
Alarm Mode
-18½C/0½F
Normal 3-Hour
Normal
Normal
N/A
N/A
Daytime Running Lights
Diesel “Wait to Start”
0.45 sec. Alarm disarm pulse
Siren Constant
Silent lock/Unlock/Start
Passive Arming
Lock Follow ignition
Unlock Follow ignition
Double Pulse Lock
Double Pulse Unlock
Long Locks
Starter Kill
Dome Light
N/A
N/A
Positive Door Pin Switch
No Alarm Mode
-25½C/-13½F
5-Hour Interval
Auto Rearm
Silent Lock/Unlock Only
N/A
N/A
Reset All Options
2 flashes
Unit turned off because Brake or Hood was activated. Check to make
sure the hood pin switch is depressed when the hood is closed and
the correct brake wire is hooked up.
3 flashes
No Tach or Stalled. Review section 12 and make sure the no tach/tach
wire option is programmed correctly.
4 flashes
Received another remote input from the transmitter
5 flashes
Transmission was shifted into gear. Move the In-Gear switch inside
the receiver module to the OFF position (see diagram below for
location of In-Gear switch inside module case).
6 flashes
Low battery voltage, or may be missing an ignition wire which
powers up the alternator
7 flashes
Alarm Input triggered
24B. Program Features Descriptions
8 flashes
Over current – One of the 400 mA (-) transistor outputs (Accessory
Pulse, Alarm Disarm, Starter kill, lock, unlock, horn, lights, trunk, or
Ignition 3) of the control or 3 pin harness is drawing too much current.
Make sure to use a relay where necessary.
Option #1
No-Tach
Tach Mode
This option sets the starting method. The factory setting uses “No-Tach” starting. If
you wish to use the tach to start, follow the instructions in the Tach Rate Learning
(section 12B).
12 flashes
The Control Switch was turned off while the starter was running.
Option #2
10 Min. Run Time
This option gives you a choice of run times.
For reasons why it last started, simply put your foot on the brake while you turn the
control switch OFF. Keep holding the brake down until the flashes start. The codes
are as follows:
1 flash
The unit has not started yet since it was last powered up.
2 flashes
Received a radio signal from the transmitter to start.
3 flashes
N/A
4 flashes
Temp reached 0o F in vacation mode.
5 flashes
Voltage reached 11 volts in Vacation Mode.
6 flashes
Received a start command from the remote input RED/BLACK wire.
7 flashes
Started from 24 hour Daily Start feature.
Option #3
Normal Crank
Extended Crank
This option will add 50% more crank time to the NoTach™ starting feature.
Option #4
Normal
IGN 2 not active during Crank
This option will turn off the Ignition 2 output (thick GREEN wire) during cranking. It
is used to exactly match the remote starter with the ignition key function.
Option #5
Normal Voltage Metering
Ignore Voltage Metering
This option is used in the “No-Tach” starting method for some diesel vehicles or
vehicles with weak batteries and/or poorly performing altenators.
Option #6
Gasoline Vehicles
Diesel Vehicles
This option must be activated when installing on a diesel vehicle.
24A. Setting Program Features
The remote starter unit has many special features available. You will not need to
use these special features in most situations. The factory settings will operate
most vehicles. You must turn the On/Off control switch to the “OFF” position
to program any features.
Option #7
“Enable” Feature
No “Enable”
This option cancels the “enable” mode safety feature. The “enable” mode
requires that the driver toggle the ON/OFF control switch “OFF” then “ON”
each time the driver removes the key from the ignition in order to “enable”
the vehicle for remote starter control. This feature guards against undesired
starting of the vehicle by remote control. You must keep this option as
enable on all GM rear wheel drive and Dodge Dakota vehicles manufactured
prior to 1996.
Note: When turning off this control switch, the red LED light will flash a few times,
giving the diagnostic code described in section 23. Wait a few seconds for it to
finish before programming your new Options.
Feature
Number
1
2
3
4
5
6
7
Factory Setting
(2 flashes)
“No-Tach”
10 Min. Run Time
Normal Crank
Normal
Normal Voltage Metering
Gasoline vehicles
“Enable” feature
© 2005 Directed Electronics, Inc.
15 Min. Run Time
Option
(1 flash)
Tach Mode
15 Min. Run Time
Extended Crank
IGN 2 not active during crank
Ignore Voltage Metering
Diesel vehicles
No “Enable”
Option #8
Normal
Daytime Running Lights
This option will automatically turn the headlights on (for safety) about 10 seconds
after it sees the key in the ignition position – and automatically turn the headlights
off when the key is removed from the ignition.
5
v5.3 J2428
Option #9
Normal
Diesel “Wait to Start”
This option will control the time before cranking the diesel vehicle by looking at the
“wait to start” light of the vehicle. Simply hook the RED/BLACK Input wire of
section 20 up to the wire behind the “wait to start” light. Also set Option #6 (section
24) for diesel vehicles.
Option #27
Normal
Auto Rearm
This option will automatically relock the doors and rearm the alarm if the doors are
not physically opened within 2 minutes of unlocking and disarming the alarm with
the transmitter.
Option #28
Normal
Silent Lock/Unlock Only
This option will remove the notification chirps for lock and unlock only. The unit will
still chirp for remote start.
Option #10
1 sec. Alarm Disarm Pulse
0.45 sec. Alarm Disarm Pulse
This option shortens the Alarm Disarm Pulse from 1 second to 0.45 second. This
feature is very useful with some Dodge/Chrysler vehicles that use a multiplexed
system to disarm the alarm and unlock the doors with the same wire. Using this
feature should eliminate the need to relock the doors after the alarm has been
disarmed and the vehicle is remotely started.
Option #31
Reset all Options
This option resets all options back to the factory settings.
PROGRAMMING AN OPTION
Option #11
Horn Pulsing
Siren Constant
This option changes the thin BLUE wire from pulsing output for horn to constant
output for a siren.
If you want the factory setting, DO NOTHING and skip this section. If you want to
change one or more of the features, TURN THE ON/OFF CONTROL SWITCH TO THE
“OFF” POSITION. Wait for the red LED light to stop flashing, then continue
with the following procedures:
Option #12
Chirp with Locks
Silent lock/Unlock/Start
This option will eliminate the chirp with Start, Lock and Unlock.
A.
Option #13
Active Arming
Passive Arming
The factory setting of Active Arming requires the owner to actively arm the car with
the remote control. Choosing the option of Passive Arming will cause the vehicle
to automatically arm after the key is removed and the door is closed.
For options 1-9: Push the white code button on the remote start module.
Each time you push the button the red LED light will flash 1 to 9 times
signifying at which feature you are (press it once, the LED light flashes once.
Press it again and it will flash two times. Press it again and it will flash three
times, etc., to show what feature you are at).
For options 10-19: Push the red code button on the remote start module. You
will see the LED light flash a long blink. This is option 10. You can scroll to
option 11 by pressing the white button once – you will see a long blink
followed by one short blink. You can scroll to option 12 by pushing the white
button again – one long and two short blinks brings you to option 12.
Option #14
Normal
Lock Follow Ignition
Selecting this option will automatically lock the doors when the key is turned on,
doors closed and the brake is depressed.
Option #15
Normal
Unlock Follow Ignition
Selecting this option will automatically unlock doors when key is removed from
ignition.
For options 20-29: Push the red code button twice to get the two long blinks
– you are now at option 20. Push the white button to jump ahead to option 21
– two long blinks and one short blink. Push three more times to get to option
24 – two long and four short blinks.
Option #16
Normal
Double Pulse Lock
This option will pulse the lock output wire twice instead of once for normal mode.
For options 30-31: Push the red code button three times to get three long
blinks – you are now at option 30. Push the white button once to jump to option
31 (three long blinks and one short blink).
Option #17
Normal
Double Pulse Unlock
This option will pulse the unlock output wire twice instead of once for normal mode.
Option #18
Short lock pulse
Long lock pulse
This option will increase the door lock pulse time from 0.6 second to 3 seconds for
vehicles with vacuum locking systems (older European vehicles).
Option #19
Alarm Disable
Starter Kill
The factory setting of Alarm Disable will give you a quick pulse whenever the
transmitter unlocks the doors or the transmitter is used to start the vehicle. The
Starter Kill option comes on and stays on whenever the remote starter is running or
the alarm is armed. This wire controls a relay which opens up the path of the starter
wire (refer to section 15).
Option #20
Accessory Pulse
Dome Lamp
Accessory pulse puts out a brief pulse output after the remote starter starts or stops
the vehicle. When set, this output can be used to turn on a defroster that requires
a momentary pulse or could be used to control GM R.A.P. (retained accessory
power) output. Dome lamp option will turn this output on when you unlock the door
for 25 seconds. (Refer to section 18).
B.
When you are at the feature level you desire, push the start button on the
transmitter for one second and the red LED light will flash once to signify
you are at the Option setting. You can push the transmitter button again
and it will flash twice to signify you are at the Factory setting. Push the
transmitter button again and you will go back to the Option setting.
C.
You can choose to change another feature by starting over again at Step A.
After six seconds, the remote starter automatically exits the programming
mode (three LED light flashes).
D.
When finished – switch the Control Switch back ON. The red LED light will
flash once.
25. External shock sensor hook up (optional):
Plug the shock sensor unit into the 4 wire connector on the front side of the remote
start module. Use one or two cable ties to tightly fasten the shock sensor unit to the
steering column of the vehicle. Make sure that the sensor does not affect the
driver's ability to steer the vehicle.
4-Pin External Alarm Input
This placement gives the best overall
coverage for a vehicle. Adjust the
Power Harness
1
2
3
4
on this side
screw(s) so that a hard impact on the
vehicle triggers the full alarm and light
1. Warn Away
2. Full Alarm
impacts just trigger the warn away. (This
3. Ground
4. +12 Volts Constant
input may not work with all types of
alarm sensors.)
Option #23
Negative Door Pin
Positive Door Pin Switch
This option changes the polarity of RED/WHITE alarm input wire. (Most Ford vehicles
use a positive door pin switch.)
Option #24
Alarm
No Alarm
This feature can disable all alarm functions if the alarm features are not desired.
Option #25
-18½C/0½F
-25½C/-13½F
This option changes the start temperature for the Vacation Option.
Option #26
Normal 3-Hour
5-Hour Interval
This option changes the minimum wait time between starts for the Vacation Option.
v5.3 J2428
6
© 2005 Directed Electronics, Inc.
SPECIAL CASES
4. Factory Anti-Theft Systems
Many vehicles come with an anti-theft system that must be temporarily bypassed
for the vehicle to be remotely started. Some systems use a resistor in the key.
Others use a transponder – a small device in the key that communicates a high
security code to the vehicle before the vehicle will successfully start.
1. How to Use a Relay
Many of the optional steps require a relay to be hooked up. The most common relay
used for this type application is the Bosch type relay (Radio Shack Cat.# 275-226).
Use the diagram below for a typical hookup. If you have another relay then you need
to know that pins 85 and 86 in this diagram relate to the coils of the relay. Pin 30
is the ‘common’, and pin 87 is the ‘normally open’ contact. If your relay has a pin
87A in the middle it is the normally closed contact and may or may not be used in
the application. (The diagram below is typical for an Ignition 3 or trunk application).
To supply +12 volt output
To supply Ground (-) output
+12 V
To Ground
From
Remote
Starter
(-)
87
+12 V
30
85
86
From
Remote
Starter
(-)
To Vehicle's Accessory
Check the list of vehicles and the types of security systems that follows. If your
vehicle is listed, your vehicle has an Anti-Theft System that the remote starter
MUST temporarily bypass in order to start the vehicle. More information about the
factory anti-theft systems and vehicle wire colors can be found at the DesignTech
Website www.designtech-intl.com.
The Universal Alarm Bypass Module (model numbers 20402 or 29402) will temporarily
bypass the factory anti-theft systems when using the remote starter. Check with
your local retailer/installer to purchase this Universal Alarm Bypass Module.
List of vehicles and the types of factory anti-theft systems:
87
+12 V
30
85
86
To Vehicle's Accessory
2. Code Learning
Your transmitter is factory coded to the remote starter module with over 16,000,000
different codes. The remote starter module can learn the codes of up to 4 different
transmitters. If you want to add additional transmitters to the receiver or if it does
not respond to your transmitter – follow the steps below to teach the receiver
the transmitter code(s):
A. Turn the Control Switch ON.
B. Push the red "code learn" button to the right of the red LED light. The red LED
light and the dash lights come on for a second. (The vehicle's ignition and
accessory wires come on).
C. While holding the transmitter at least three feet from the module, hold down the
Start button (on a five button transmitter) or the lock/unlock button (on a three
button transmitter) until the red LED light and the dash lights come on again for
a second. The module has now learned the transmitter code. Release the
transmitter button.
D. To learn additional transmitters (up to 3 more), immediately (within 5 seconds)
push the Start button (on a five button transmitter) or the lock/unlock button (on
a three button transmitter) on another transmitter for a few seconds until the red
LED light and the dash lights come on for a second again.
E. 5 seconds after the last time the transmitter was learned the unit exits the
code-learning stage. (The red LED light, ignition and accessories flash 4 times).
Note: Teaching the module a new transmitter code will erase all previous codes so all transmitters must be taught. You have only 5 seconds between transmitters
to begin teaching a new transmitter.
3. Diesel Vehicles
For the most relible starting, hook up the RED/BLACK wire referenced in section 20.
For difficult starting diesels connect and learn the tach (section 12) as well as the
wait-to-start RED/BLACK wire (section 20). Set Option #6 (section 24) for diesel.
For most diesel vehicles, you can start the vehicle without needing to hook up a
tach wire. The following table provides the mandatory option settings for “no-tach”
operation in diesel vehicles. (Use the Chrysler settings for all other diesel vehicles.)
Option #6
Diesel
Engine
Option #3
Extended
Crank
Chrysler
■
■
Ford
■
■
■
Chevrolet
■
■
■
© 2005 Directed Electronics, Inc.
Option #5
Ignore
Meter
7
Vehicle:
System:
Vehicle:
System:
Acura 3.2TL 98+
Audi A4,A6,A8 98+
Acura CL 97+
Acura Integra
Acura NSX
Acura RL 98+
BMW (all 97 +)
Buick LeSabre 90 - 01
Buick Park Ave 91 - 96
Buick Park Ave 97+
Buick Regal 93 -96
Buick Rendez Vous
Buick Riviera 93 -96
Buick Roadmaster 93 - 96
Buick Skylark 96-98
Cadillac Allante
Cadillac Brougham
Cadillac Catera 97+
Cadillac DeVille 92 - 98
Cadillac DeVille 99+
Cadillac Eldorado 89 - 98
Cadillac Eldorado 99+
Cadillac Escalade 00+
Cadillac Fleetwood 90 - 96
Cadillac Seville 90 - 98
Cadillac Seville 99+
Chevrolet Astro Van 98+
Chevrolet Avalanche 01
Chevrolet Blazer 98+
Chevrolet Camaro 86 +
Chevrolet Cavalier 96-99
Chevrolet Cavalier 2000+
Chevrolet Corvette 88 +
Chevrolet Express 97+
Chevrolet Impala 2000+
Chevrolet Lumina 96 -99
Chevrolet Malibu 97 -01
Chevrolet Monte Carlo 96-99
Chevrolet Monte Carlo 00+
Chevrolet Pickup Full-size 98+
Chevrolet S-10 98+
Chevrolet Silverado HD 01
Chevrolet SSR 01
Chevrolet Suburban 98+
Chevrolet Tahoe 98+
Chevrolet Trailblazer 01+
Chevrolet Van 98+
Chevrolet Venture 99+
Chrysler Concorde 98+
Chrysler LHS 99+
Chrysler PT Cruiser 00+
Chrysler Sebring Conv. 98+
Daewoo Leganza
Dodge 300 M 99+
Dodge Intrepid 98+
Dodge Neon 00+
Ford Contour 97 +
Ford Crown Victoria 98+ (option)
Ford Excursion 01+
Ford Expedition 97+
Ford Explorer 98+
Ford Focus 01+
Ford Mustang 98+
Ford Pick Up (optional)
Ford Ranger 99+(optional)
Ford Sport Trac 01
Ford Taurus 96 +
Ford Windstar 2000 +
GMC Envoy 01+
GMC Jimmy 98+
GMC Safari 98+
GMC Denali 99+
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
VATS
VATS
Transponder
VATS
Transponder
VATS
VATS
Passlock
VATS
VATS
Transponder
VATS
Transponder
VATS
Transponder
Passlock
VATS
VATS
Transponder
Passlock II
Passlock
Passlock II
VATS
Passlock
PasslockII
VATS
Passlock
Passlock II
VATS
Passlock II
VATS
Passlock II
Passlock II
Passlock II
PasslockII
Passlock
Passlock II
Passlock II
PasslockII
Passlock II
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Passlock II
Passlock II
Passlock II
Passlock II
GMC Sierra
GMC Sonoma 98 +
GMC Suburban 98+
GMC Yukon 98+
Honda Accord 98+
Honda Odyssey 98+
Honda Prelude 98+
Honda S2000
Infiniti I30 98+
Infiniti Q45 98+
Infiniti QX4
Jaguar (all 98+)
Isuzu Hombre 98+
Jeep Grand Cherokee 99+
Jeep Liberty
Jeep TJ (Wrangler) 99+
Lexus (all 97+)
Lincoln Blackwood
Lincoln Continental 97+
Lincoln LS 2000+
Lincoln Mark VIII 97+
Lincoln Navigator 97+
Lincoln Town Car 97+
Mazda Tribute
Mercedes (all 97+)
Mercury Cougar 99+
Mercury Grand Marquis
Mercury Mountaineer 98 +
Mercury Mystique 97+
Mercury Sable 96+
Mini Cooper 02
Mitsubishi Eclipse
Mitsubishi Galant
Nissan Frontier S/C
Nissan Maxima 98+
Oldsmobile Achieva 95
Oldsmobile Achieva 96+
Oldsmobile Alero 99+
Oldsmobile Aurora
Oldsmobile Bravada 98
Oldsmobile Cutlass 97+
Oldsmobile Eighty-Eight
Oldsmobile Intrique 98+
Oldsmobile Ninty-Eight
Oldsmobile Silhoutte 99
Pontiac Aztek 01
Pontiac Bonneville 89+
Pontiac Firebird 88+
Pontiac Grand Am 96 - 98
Pontiac Grand Am 99+
Pontiac Grand Prix 92 – 96
Pontiac Grand Prix 97+
Pontiac Montana 99+
Pontiac Sunfire 96-99
Pontiac Sunfire 2000+
Porsche (all 97+)
Saab (all 97+)
Saturn 97-99
Saturn 00+
Subaru Legacy 00+
Subaru Outback 00+
Toyota Avalon 98+
Toyota Camry 98+
Toyota Highlander 01+
Toyota Land Cruiser 98+
Toyota Solara 99 +
Toyota Supra 98+
Volkswagen Beetle 98+
Volkswagen Golf 98+
Volkswagen Passat 98+
Volvo (all 98+)
Passlock II
Passlock II
Passlock II
Passlock II
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Passlock II
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Passlock I
Passlock II
Passlock II
VATS
Passlock II
Passlock II
VATS
Passlock II
VATS
Transponder
Transponder
VATS
VATS
Passlock
Passlock II
VATS
Transponder
Transponder
Passlock I
Passlock II
Transponder
Transponder
Factory Alarm
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
Transponder
v5.3 J2428
NOTICE to Installers of Remote Vehicle Starters
We DO NOT recommend installing ANY remote starter in the following vehicles: Audi 1998+, BMW 1998+,
Jaguar 1998+, Land Rover 1998+, Mercedes 1998+, Range Rover 1998+, Volvo 1999+
As with any aftermarket installation, please research and learn as much as you can about the vehicle before you start the install.
All General Motors (GM) vehicles built prior to 1995 with automatic transmissions and all Dodge Dakota trucks with automatic transmissions
built prior to 1996 have a MECHANICAL type of NEUTRAL SAFETY SWITCH. All vehicles built after 1996 use an electrical type of neutral safety
switch.
Applying +12 volts to the starter wire on any vehicle vehicle using a mechanical neutral safety switch will engage the vehicle’s starter, regardless of the shifter’s position.
When the shifter is in Park or Neutral, the vehicle will just start up normally. If the vehicle is accidentally left in gear and power is applied to the start wire, such as by a
remote starter, the vehicle will lurch forward or back as it attempts to start.
To test if your GM or Dodge vehicle is using a mechanical neutral safety switch system, you will only be able to remove the key from the ignition switch when
the shifter is in the Park or Neutral position.
To prevent this problem from occurring when installing a DesignTech International remote starter on a GM vehicle or Dodge Dakota built prior to 1996:
1. You must leave the Enable Feature (option #7 in the factory setting). This is a safety feature that requires the user to turn the control switch OFF and then ON again each
time they exit the vehicle in order for the unit to be operational. This feature will ensure that the user of the vehicle with the remote starter installed has made a conscious
decision to allow the remote starter to start the vehicle the next time the transmitter button is depressed.
2. You must use the relay drawing below to create a circuit that will prevent the remote starter on these GM and Dodge vehicles from starting the vehicle unless the key is
completely removed from the ignition switch.
87
Connect to
constant
(+) 12 volts
85
To (-) Vehicle's Ground
87a
86
30
Connect to the
Ignition Key Sense
Wire from Vehicle's
Ignition Harness
Connect to Purple Wire (hood pin
switch) of the Remote Starter
(Purple Wire must also connect to
hood pin switch)
As with any aftermarket installation, please research and learn as much as you can about the vehicle before you start the install. Instructions, technical tips and detailed wiring
information is available on www.designtech-intl.com. Please refer to the information on the web site before starting ANY install or call Directed Electronics Technical
Support at (800) 876-0800.
v5.3 J2428
8
© 2005 Directed Electronics, Inc.
The company behind this system is Directed Electronics, Inc.
Since its inception, Directed Electronics has had one purpose, to provide consumers with
the finest vehicle security and car stereo products and accessories available. The recipient
of nearly 100 patents and Innovations Awards in the field of advanced electronic technology,
DIRECTED is ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout North America
and around the world.
Call (800) 876-0800 for more information about our products and services.
Directed Electronics is committed to delivering world class quality products
and services that excite and delight our customers.
Directed Electronics, Inc.
Vista, CA 92081
www.designtech-intl.com
www.directed.com
© 2005 Directed Electronics, Inc. – All rights reserved
06-05
9
v5.3 J2428
USER TIPS AND NOTES
v5.3
The Remote Car Starter must be “enabled” each time the driver has finished driving and taken out
the key in order for the unit to start the vehicle remotely. After the key has been removed, you must turn
OFF the control switch and then turn it back ON again while no key is in the ignition. This “control switch” or “set
switch” prevents unauthorized starting of the car by someone unfamiliar with the system who may be using the
vehicle. If you forget to set the switch, it may also be activated by pushing the transmitter and holding the button
down for ten seconds. To eliminate the need for this, see Option #7.
The AutoCommand® Remote Car Starter will turn the car off if the driver does not insert and turn the key within
10 or 15 minutes. After the AutoCommand® Remote Car Starter has started your car, simply put in the key and
turn it to the “run” or “on” ignition position (not the crank position) to drive away.
The AutoCommand® Remote Car Starter has numerous safety and security features that make it difficult to steal
your car without the key being in the ignition. Putting your car in gear, tapping the brake pedal or opening the hood
will turn the unit off unless your key is in the ignition and turned to the “run” or “on” position.
If all features are hooked up, your transmitter will function as follows:
Button 1:
Button 2:
Button 3:
Button 4:
Button 5:
Do not push for your first ‘main’ vehicle
Once: To operate vehicle #2 - then any of the 4 buttons (LED flashes red
and green)
Again: For vehicle #3 - then any of the 4 buttons (LED flashes red)
Again: For vehicle #4 - then any of the 4 buttons (LED flashes green)
Once: Start the car with all accessories left on
Again: Stop the car
Once: Turn on headlights for 30 seconds
Again: Turn off headlights
Hold down for 4 seconds for PANIC mode (45 seconds long)
Lock the doors / arm the alarm
Unlock the doors / disarm alarm (if you get 4 chirps – that means the
alarm was triggered while you were away)
Hold down for 4 seconds for Trunk
The LED on the transmitter will display 3 different colors - Red for button #2, Yellow for button #3, and Green for
buttons #4 and #5. The transmitter is powered by a long life lithium battery (CR 2032 style). The transmitter and
receiver module are FCC and DOC approved.
Alarm Disarm without transmitter: If the doors are locked and the alarm is set and you’ve lost your
transmitter, you can disable the alarm. Here is how: Enter the vehicle (alarm will sound) and insert the key and
turn it to the ‘run’ position (the position where the dash lights come on). Turn the On/Off switch off and on 4 times
in a row to disable the alarm.
Valet Mode: Turning the Control switch off puts you in Valet Mode. In Valet Mode the Remote Car Starter and
the alarm will not function. This lets you turn off the car starter when having the vehicle serviced. The only
functions that work in Valet Mode are the keyless entry, lights and panic. The red LED dash light will flash twice
every few seconds when in Valet Mode.
The Quick Stop Option™: You can leave the car running and take the key with you for a quick visit to a store.
With the car running, push the Start button on the keychain transmitter just before pulling out the key. The car will
run for 10 minutes or until you tap the brake or put the car in gear.
© 2005 Directed Electronics, Inc.
The Cold Start Option™: This automatically starts and runs the car for the preset run time (10 or 15 minutes) if
the temperature drops below 0°F or if the battery voltage drops below 11 volts. Tapping the brake at any time after
programming disables this feature. Here is how to set this feature: Hold the Start button down while the vehicle
starts, runs, turns off and the lights begin to flash 5 times. Release the transmitter button. You have set the Cold
Start Option™.
limited lifetime consumer warranty
Directed Electronics, Inc. (hereinafter “Directed”) promises to the original purchaser to repair or replace
with a comparable reconditioned Directed remote start keyless entry unit if this Directed remote start
keyless entry unit (hereinafter “Unit”), excluding without limitation, any remote transmitters or associated
accessories, proves defective in materials or workmanship under normal use for the life of the vehicle
which the Unit is originally installed. During this period, so long as the Unit remained installed in the
original vehicle, Directed will at its option, repair or replace this Unit if it is proved defective in workmanship
or material PROVIDED the Unit is returned to Directed’s warranty department at One Viper Way,
Vista, CA 92081, along with $20 postage and handling fee, a bill of sale or other dated proof of purchase
bearing the following information: Date of purchase, name and location of the merchant who sold the
Unit, and product description. This warranty does not cover labor costs for the removal or reinstallation
of the Unit. This warranty is non-transferable and does not apply to any Unit that has been modified or
used in a manner contrary to its intended purpose, and this warranty does not cover damage to any Unit
caused by installation or removal of the Unit. This warranty is void if the Unit has been damaged by
accident or unreasonable use, neglect, improper service or other causes not arising out of defects in
materials or workmanship. Directed makes no warranty against theft of a vehicle or its contents.
THE FOREGOING WARRANTY IS THE EXCLUSIVE PRODUCT WARRANTY, OTHERWISE,
ALL WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED
WARRANTY, WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR
PURPOSE ARE EXPRESSLY EXCLUDED AND DISCLAIMED TO THE MAXIMUM EXTENT
ALLOWED BY LAW, AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON
TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT.
DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES
INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. SOME STATES DO NOT ALLOW
THE LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
LIMITATION OF DAMAGES AND LIABILITY. CONSUMER’S REMEDY IS LIMITED TO REPAIR
OR REPLACEMENT OF THE UNIT, AND IN NO EVENT SHALL DIRECTED’S LIABILITY
EXCEED THE PURCHASE PRICE OF THE UNIT. IN ANY EVENT, DIRECTED SHALL NOT BE
LIABLE FOR ANY DAMAGES INCLUDING, BUT NOT LIMITED TO, ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, LOST PROFITS, LOST
SAVINGS, OR, TO THE EXTENT ALLOWED BY APPLICABLE LAW, DAMAGES RESULTING
FROM DEATH OR INJURY ARISING OUT OF OR IN CONNECTION WITH THE
INSTALLATION, USE, IMPROPER USE, OR INABILITY TO USE, THE PRODUCT, EVEN IF
THE PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES
DO NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU. THE CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN
THE CONSUMER AND DIRECTED SHALL BE RESOLVED IN ACCORDANCE WITH
CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA.
IMPORTANT NOTE:
This product warranty is automatically void if its date code or serial number is defaced,
missing, or altered.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
➤ Date of purchase
➤ Authorized dealer’s company name and address
➤ Item number
Daily Start™: This allows you to start the vehicle at the same time the next day. For example, if you leave for
work at the same time each morning you can use the Daily Start™ feature to automatically start your car the next
day. Here is how: Start your car with the transmitter as usual. When you enter the vehicle and before you put the
key in the ignition, put your foot on the brake to turn the AutoCommand® off. Now within five seconds toggle the
control switch off and on once while your foot is still on the brake. The dash lights will flash once to signal the
setting of this option. Your vehicle will now start approximately 23 hours and 50 minutes later and run its normal
cycle. You can still start the vehicle with the key or via the transmitter anytime without cancelling out this option.
Safety Notices:
1. When taking your car in for any service or repairs, disable the remote starter by switching the
Control switch to the OFF position. Inform the mechanic.
2. Never leave your keys in the Ignition when the vehicle is unattended.
3. Do not use this product in a closed garage to avoid excessive carbon monoxide build-up.
Available Accessories:
Universal Alarm Bypass Module allows remote car starter installation on newer vehicles with factory anti-theft
systems such as VATS, P.A.T.S., Passlock I, Passlock II, Pass-Key III, Saturn, Securlock, and Transponder systems.
Extra transmitters for more than one user in the family. Up to four transmitters can be used with each receiver in the
vehicle.
These products can be purchased through your dealer.
Directed Electronics, Inc.
Vista, CA 92081
www.designtech-intl.com
www.directed.com
© 2005 Directed Electronics, Inc. – All rights reserved
06-05
Remote Car Starter Keyless Entry Notes Sheet for Model #s 28624T & 28628
Thank you for purchasing DesignTech unit that offers keyless entry features. Proper installation will result in
years of trouble free keyless operation including locking and unlocking your vehicle’s door locks and trunk control.
Please read these instructions completely prior to beginning connection to the vehicle’s locks and trunk.
GENERAL GUIDELINES AND CAUTIONS:
• Obtain a vehicle wiring sheet for your specific vehicle indicating the location, colors and types of locks and trunk
system that you will be working with. Please note that it may be necessary for you to purchase external relays
and/or diodes and resistors that are not included with your product. Please visit the DesignTech website at
www.designtech-intl.com
•
When testing for lock/ unlock/ trunk wires, closely follow the instructions and when checking electrical
connections, use a test meter (multi-meter, voltage meter, etc.), DO NOT use a test light. It is easy to
accidentally damage the circuitry in modern vehicles testing for wires with a test light.
•
The better you make your connections, the more reliable your system will be. We recommend soldering all
connections.
•
All chassis ground wires must go to clean, bare metal surfaces. Always test the spot you have chosen for ground
connections to make sure it is a good ground. Pieces of metal supporting or attached to the underside of the
dashboard are not good locations. The best spot is usually in the kick-panel.
•
Some door lock circuits will require that up to three wires on the DesignTech module be attached to +12 volts.
When doing this, connect all these wires together and then put the fuse on the main wire so that all wires are
protected with the fuse.
NEGATIVE TRIGGERED DOOR LOCK SYSTEMS
This circuit style is common to
most Japanese cars and some
European cars as well. In this
circuit the door lock/ Unlock
switch activates a relay which in
turn activates the lock/ unlock
motors in the car doors. The
DesignTech module will be
connected so that it provides a
negative pulse to the
appropriate wires to lock or
unlock the doors.
Testing for this type system is
very simple. First, check the
Keyless Entry wiring guide and
determine the color and location
of the lock wires in the vehicle
you are working on. Set your
test meter on continuity (or
ohms) and clip or attach one of
the probes to the cars chassis.
AutoCommand Keyless Entry Notes Sheet Without Relays.doc
9/7/2004
Test the chassis connection you are using by touching the other probe to a different point on the cars chassis. The
meter should register continuity, or a "continuous" circuit (zero ohms).
Next, locate the lock/ unlock wires (the ones from the wiring guide) in the car by removing whatever panel or
covering you need to. With one probe from the meter still attached to the cars chassis, use the other probe and
pierce the insulation of the lock wire. If you are on the correct wire, the meter should register continuity when you
press the lock switch. When you check for unlock the meter will register when you press the unlock switch. These
wires will register continuity ONLY when the corresponding lock or unlock switch is pressed. When you have found
the correct wires, connect the DesignTech module according to the diagram above.
POSITIVE TRIGGERED DOOR LOCK SYSTEMS
This circuit is similar to the
negative system except that
instead of a ground pulse to lock
and unlock, the system requires a
+12 volt pulse to lock and unlock
the doors. This type system is
found in most GM cars. When
testing for this system, attach the
black probe from the test meter to
chassis ground and set the meter
on the +12 volt DC scale. Use the
red probe from the meter to check
the wires. The meter will register
around +12 volts on the lock wire
when you press the lock switch
and the meter will register the
same for the unlock wire when
you press the unlock switch. These
wires will register +12 volts ONLY
when the lock or unlock switch is
pressed. When you have located
the correct wires, connect them exactly according to the following diagram.
REVERSE POLARITY DOOR LOCK SYSTEMS
Reverse polarity systems are more complicated. The switch in the vehicle sends +12 volts in one direction while
holding chassis ground on the other direction. This is true for both lock and unlock. Testing for this system requires
to check for continuity to chassis ground on the lock and unlock wires at rest. Just like a positive triggered system,
the lock wire will register +12 volts when you press the lock switch, and the unlock wire will register +12 volts when
you press the unlock switch. When neither switch is being pressed, these wires will show ground on your meter.
When you have located the correct wires, cut them in half. The switch side will still measure continuity to chassis
ground at rest while measuring +12 volts when the switch is activated. The motor side will not meausure anything
at either rest or when the switch is activated. Once you have determined which is the switch side and which is the
motor side, connect them to the DesignTech module according to the diagram on the next page using two SPDT
(Single Pole Double Throw) 5 pin relays.
AutoCommand Keyless Entry Notes Sheet Without Relays.doc
9/7/2004
SINGLE WIRE DOOR LOCK SYSTEMS
Single wire door lock systems
have only recently come in to
the market in the last five
years or so. This type of door
lock system differs from
more traditional wiring
systems as it only uses one
wire to both lock and unlock
the doors. Varying by make
model and even year of
vehicle, this system either
switches +12 volts or ground
across a resistor. The value of
the resistor is different for
lock and unlock, allowing the
vehicle to determine which
action is desired. If your
vehicle has this type of door
locking system, it is critical
that you get the wiring
information either faxed to
you or off of our web site
(www.designtech-intl.com). Use the diagram above to guide you through the wiring using two SPDT (Single Pole
Double Throw) 5-pin relays.
AutoCommand Keyless Entry Notes Sheet Without Relays.doc
9/7/2004
Trouble-Shooting Guide
Unit won’t respond
Make sure unit has power and ground.
Make sure unit is initialized (See ‘Initializing the unit’ in the manual)
Re-program transmitter. (See ‘Code Learning’ under Special Cases in the manual).
What is the Diagnostic
Code, and how do I
get it?
Diagnostic Code 1 flash
Check Diagnostic Code as described in Trouble Shooting with Self Diagnostics in the manual.
The Self-Diagnostics built into every DesignTech brand remote start will help identify problems in both the unit and
your installation. To get an accurate diagnostic code, flip the toggle switch off and back on; the LED light (on
module) should flash once if the unit is initialized. Press the start button on your transmitter for second. Now allow
the unit to try and start your vehicle 1-3 times. (Note that the unit will attempt to start the vehicle up to 3 times unless
codes 2,5,7 or 8 are being triggered, when it will try and start the vehicle once). Allow it up to a minute to try to start
again on its own - Don’t do ANYTHING to the unit during this time, unless something goes obviously wrong. At the
end of the starting cycles, turn the toggle off and count the first series of flashes- this will be the diagnostic code.
The unit may not have attempted to start the vehicle yet or the unit may have started and timed out.
Is the toggle switch upside down? When the switch is turned on the LED will flash once immediately.
Something might be causing the unit to reset, such as a poor connection to ground or power, or you may have a relay
wired improperly. Typically the wires in the control harness require a relay unless otherwise stated.
Diagnostic Code 2 flashes
The transmitter may need to be programmed.
The unit thinks the hood is open. Make sure the hood pin-switch is properly adjusted and installed.
The unit thinks the brake is being depressed. Make sure the brake wire has 12 volts on it only when the brake is
depressed. There should be no voltage on the brake wire at any other time
Diagnostic Code 3 flashes
You might be experiencing feedback if you have connected the parking or head-lights. If disconnecting the lights
wire allows the unit to start then you might power the headlights, or you can isolate the brake wire of the unit from
the vehicle with a relay.
If the unit is programmed for tach, the tach wire is not connected or the tach rate may not yet have been learned.
If the unit is programmed for ‘No-Tach’ the vehicle may not have all the required ignition wires connected, or may be
equipped with a factory security system – thus causing it to stall.
Diagnostic Code 4 flashes
Sometimes a unit may have an option programmed even though you did not specifically set that option. Try re-setting
the unit. Unplug everything from the module except the black ground wire and LED (if you have a plug-in LED).
While pressing the white button on the module, connect the power lead. The LED on the unit should turn on and stay
on. Release the white push button and the LED should remain illuminated. (If not, repeat the process being sure to
hold in the white button while connecting power.) Now remove power and wait 2 minutes. Then connect the power
without pushing any buttons. Re-Initialize the unit and it should work for you.
Make sure the remote input wire (usually red/white) is not touching anything. (This wire is not on all models). If you
have a stick shift unit – this is not relevant to you.
You might be pressing the remote control again before the unit has completed its cycle(s)---See 'Diagnostics: What is
the Diagnostic code and how do I get it?’ – at the top of this page.
Diagnostic Code 5 flashes
Diagnostic Code 6 flashes
If installing a manual transmission unit, this code means the unit did not see the door pin-switch.
This code means the unit thought the transmission was shifted into gear.
If the transmission was not shifted: Switch the “in-gear” switch inside the module to the off position. This disables
‘Transmission in Gear’ sensing, and should solve the problem.
Code 6 is caused by the unit not seeing the battery voltage increase enough when the vehicle starts. It can also be
caused if you are not bypassing the factory theft system, such as PATS, VATS, or similar, if equipped.
Double-check the ignition wiring against the vehicle-wiring guide. Your vehicle may require ignition 2, or in some
cases ignition 3, in order to allow the alternator to function – thus bringing up the voltage.
Diagnostic Code 7 flashes
Diagnostic Code 8 flashes
Diagnostic Code 9 flashes
Diagnostic Code 10/11 flashes
Diagnostic Code 12 flashes
© 2005 Directed Electronics, Inc.
If the wiring is correct, and you are properly bypassing any security system the vehicle may be equipped with, then
connecting the unit into tach mode should solve the problem. (Your alternator may not be functioning properly).
An alarm sensor was triggered, causing the vehicle to shut down. (Only applies to units that have alarm features).
Something in the control harness is not connected properly. One of the transistor outputs is driving too much current.
There may be a wire connected without a required relay, or if you are using a relay, the relay may not be connected
properly.
Applicable only to manual transmission units. Indicates the unit did not see the emergency brake.
These are not a valid codes.
Make sure you have an accurate code. Please see ‘What is the Diagnostic Code, and how do I get it?’ at the top of
this page. If you still get code 12, one of the toggle switch wires may have touched ground, possibly damaging the
unit. Or maybe the switch was just turned off while it was running. Or maybe a defective switch?
1
Trouble Shooting v4-1
Initialization - What is
it?
Initialization - What if
the unit will not
initialize?
Initialization is a process which proves to the unit that you have connected the required safety features and that the
unit has been installed in an automatic vehicle. See “Initializing the Remote Starter” in the manual.
DO NOT ATTEMPT TO INITIALIZE or INSTALL ANY AUTOMATIC UNIT ON ANY MANUAL
TRANSMISSION VEHICLE! Attempting to force an automatic unit to function on a manual stick-shift
vehicle could result in serious property damage or personal injury!
Is the unit already initialized? Make sure the switch is not upside down. Toggle the switch off and then
back to on. As the switch is turned on, the LED light on the unit (or that plugs into the unit) will flash
once if the unit is initialized.
One of the ignition wires may have voltage on it. Make sure all ignition wires measure a “dead” 0 volts
when the key is “off.” (It is normal to measure a small amount of voltage from the unit’s start wire.)
Check that there is 12 volts on the orange wire in the control harness only when the brake is pressed.
Check that there is continuity to ground on the purple wire in the control harness only when the hood is
open.
(A good way to test both the hood and brake at the same time is to connect a test light – the kind with a real light bulb
– with one lead to the orange wire and the other lead from the test light connected to the purple wire. If you open the
hood and press the brake, the light will illuminate if both connections are correct.)
You may have the wrong start wire. Make sure the yellow start wire from the unit is connected to a wire
in the vehicle which shows 12 volts only when the key is in the start (cranking) position. The wire should
have power at no other time.
Did you mistakenly switch the “in-gear” switch inside the module? If so, the unit will not initialize. This
switch disables transmission in-gear sensing, and should only be switched if you have been instructed by
a technician to do so or you are getting a diagnostic code of 5 flashes.
Your vehicle may not have a neutral safety switch, such as pre 95 GM rear-wheel drive vehicles or Dodge
Dakotas built prior to 1996. Try this: Open the hood and place your foot on the brake. Start the vehicle
with the key. Turn the engine off and release the brake. If all of your connections are correct the unit
should be initialized at this point.
I have a GM Truck and
the “Check Engine”
light is on after remote
starting. What should I
do?
The vehicle cranks but
fails to actually start
My 3 button remote
control will lock the
doors but will not unlock
them.
Try bypassing the toggle switch temporarily in case a wire or connection to it is broken. Just unplug the
switch and jump across the two pins on the module that the switch plugs into with any metal object. As
you jump (short) the two pins together the LED should flash if the unit is initialized. NOTE- DO NOT
short any toggle switch wire to ground or probe the connector with a test light. Doing so may damage the
unit.
You most likely have one of the ignition wires connected wrong. Make sure you have connected:
From Unit
to Vehicle_______________________________
Ign1 (Blue)
PINK (hot in run and start)
Ign2 (Green)
WHITE or PINK/WHITE (hot in run and start)
ACC(White)
ORANGE (hot in run only)
If you have the ignition wires connected as above and still have a check engine light it is possible the unit
has been programmed to have ignition 2 “off during crank.” Please review the programming options
within the installation manual.
Please see “What is the diagnostic code and how do I get it?” Follow the steps for the diagnostic code
you receive. You are probably missing one of your second or third ignition wires. Or if it is a Nissan –
you probably have 2 starter wires which need to be shorted together.
Re-program the transmitter. Use the left button when teaching 3 button remote controls. When
programming the 5 button remote, use the start button. (Refer to the installation manual for the complete
steps on how to make the unit enter the code learning process.)
My 5 button remote will
not control lock/unlock
individually.
© 2005 Directed Electronics, Inc.
2
Trouble Shooting v4-1
The vehicle runs – but
without the heater or airconditioner.
I have poor range.
You are missing the 2nd (or 3rd) ignition wire or the accessory wire is not hooked up. Make sure the heater or airconditioner is left on when you leave the vehicle. On diesel vehicles – they may not come on for a few minutes until
after the vehicle is up and running.
My vehicle has Passlock
I or II and I cannot get a
resistance reading.
Many meters have a known issue with measuring passlock. This is not a fault of the meter, the installer, or
the manufacturer. These issues can cause problems such as getting a consistent reading of the resistance,
or the reading may be artificially inflated. It is our belief that the mid-to-high-end meters seem to
experience more problems measuring passlock than less expensive digital meters.
Can I use the
DesignTech Transmitter
with other brands of
products?
The LED on the unit
flashes constantly
The antenna coax wire may be crimped, cut or otherwise damaged. Try the antenna both vertically and horizontally
to determine the best performance. Make sure the receiver unit has a good chassis ground. Note that the higher you
hold the transmitter off the ground when pushing the button – the further distance you will get from the system.
One wire will have 0 volts - This is the wire you "tap" into-- we’ll call this WIRE #1 USUALLY BLACK
OR ORANGE/BLACK. One wire will have 5 volts or less- This is the wire you cut in half-- we'll call this
WIRE #2 USUALLY YELLOW. One wire will have aproximately 12 volts - This is the wire you leave
alone USUALLY WHITE OR BLACK/WHITE. With all PASSLOCK wires intact, turn the vehicle on
and bump the starter. Measure the voltage between the wire #1 and wire#2. Your meter should be set on
the 12 volt DC scale. RECORD THIS VOLTAGE. Without turning the key off - go ahead and separate
WIRE #2. Reconnect the Universal Alarm Bypass Module (Part #20402 or 29402) as described in the
installation manual with one exception - GROUND the wire that goes to the ignition 3 wire; you should
hear the bypass module click. Now measure the voltage between the ENGINE side of WIRE #2 and wire
#1. Your meter should be set on the 12 volt DC scale. Adjust the dip-switches and trim-pot on the bypass
module until the voltage being measured EXACTLY matches the recorded voltage obtained without the
module. Remove ground from the ignition 3 wire of the bypass module, turn the vehicle off and then
restart it. Look at the voltage again - and while monitoring it ground the ignition 3 wire of the bypass
again. If the module is set correctly the voltage should NOT change. Repeat again to verify - if you get
the same voltage every time then the module is set up perfectly. There is no chart to help you with this, it
is just trial and error -- but it will work regardless of the meter you are using.
NO. Due to proprietary technology DesignTech brand products will operate only with DesignTech brand
Transmitters. Likewise, a DesignTech transmitter will not operate another brand’s products.
The alarm within the unit, if equipped (as are most units with 3 or 5 button remotes) may be armed, or the
unit may be in valet mode.
Make sure the wires going to the toggle switch are not broken, and that the toggle switch is on.
The LED remains
illuminated at all times
The starter stays
engaged for 6 seconds.
Reset the unit - See “Resetting all options to the factory setting” in the instructions
It is normal for the LED to glow dimly. This indicates the unit is receiving power.
If the LED is at full brightness then one of the push-buttons may have been depressed when you applied
power, the LED may be plugged into the wrong jack, or something may be wrong within the unit.
If the unit is in tach mode – make sure the tach wire is properly connected and receiving the correct tach
rate.
If using the “No-Tach” method, make sure the unit is not programmed for tach mode, extended crank, or
super crank.
Make sure you have the correct start wire connected - the start wire in the vehicle should have 12 volts
only when the key is in the start position.
How will I know if I
need a relay?
Some vehicles such as Toyotas and Nissans, experience a starter feedback problem. Try temporarily
isolating the start wire from the key switch to identify this problem - simply cut the start wire in half
between the connecting point of the units start wire and the key switch. Get Installation Note #133 from
off our web-site or Fax On Demand.
If the output is labeled as a “+12 relay output” the unit contains a relay on that output - and you will only
need to use a relay if the vehicle requires a negative output.
If the output is labeled a “400ma Transistor Ground Output”, this means the unit supplies a ground up to a
maximum of 400ma. If more than 400ma is drawn through the output, the unit may shut down or it may
be damaged. Generally speaking, if the vehicle requires a ground and the unit supplies a ground you will
not need a relay. If the vehicle requires a positive and the unit supplies a ground, you will need to use a
relay. Likewise, if the vehicle requires a ground capable of more than 400ma you would need to use a
relay. See Installation Note 111, Basic Uses of the Relay from our web site or our Fax On Demand.
© 2005 Directed Electronics, Inc.
3
Trouble Shooting v4-1
Vehicle only remote
starts if I flip the toggle
switch off and back on
This condition is perfectly normal. This is a safety feature designed to prevent unauthorized starting. If
you have forgotten to flip the switch off and back on, you can still remote start the vehicle. Just hold the
start button down for 6 to 10 seconds instead of the usual 1 second. If you do not like this safety feature, it
can be permanently bypassed by programming option 7, explained under "Setting Programming Features"
or a similar section within the installation instructions.
The remote input wire available on some units (usually a red/white) may be connected to ground. The
remote input wire should be taped up if not being used so that it does not touch ground.
The car turns off when
the brake is pressed- but
as soon as I release the
brake the vehicle starts
again
The alarm has been armed and triggered – even if you did not hook it up. If the alarm features are not
The lights flash (and
being used, you must ground the ‘alarm trigger’ wire permanently, or set option 24 if available.
maybe even the horn)
when I step on the brake.
Program extended crank, or use tach mode.
The unit tries 2 or 3
times before getting the
vehicle up and running
Some General Comments:
•
For Your Safety, never install an automatic unit into a manual transmission (stick-shift) vehicle! Serious
property damage or personal injury including death may occur! Instead, use one of our special manual
transmission units, which will operate safely in a manual transmission vehicle.
•
When testing wires use only a digital multimeter, unless otherwise instructed. A test light (especially the
kind with a real light bulb) can severely damage electrical components in modern vehicles if used
improperly. Also, “computer safe” LED type test lights - with a red and/or green LED- are NOT airbag
safe! NEVER test ANY wire within an airbag system harness.
•
Always roll down at least one window in the vehicle before beginning work. This will prevent you from being
accidentally locked out of the vehicle.
•
It’s okay to have a battery charger on the battery while you are working on the vehicle, but the car starter will
not function correctly with the charger attached.
•
Specific vehicle information is available directly from www.designtech-intl.com. If you have trouble with the
colors in the wiring guide "matching up" then you may be in the wrong harness. You can make sure you are in
the correct harness by unplugging the wires. For example: With the ignition switch, if you unplug it and then
the vehicle no longer cranks, the blower and radio do not work, and the vehicle is for all purposes "dead" with
the key- then you have found the “ignition switch harness.” (Otherwise, you will need to continue searching...)
The same technique can be used for the brake, lights, horn, etc. Once you are sure you are in the correct
harness, if the wire colors still fail to match up then you will have to test the wires using a digital multimeter. It
is always best to verify any wire before connecting to it.
•
Most of the common questions that people ask are actually answered within the installation manual. Make sure
you have thoroughly reviewed it before calling for technical support. We recommend going through the
installation manual with two different colored markers. Read through each step and check it off after you have
read it. Use the second marker to make a check when you have completed the step in the vehicle. This will help
to make sure you have completed all steps, and that you have not missed any features the unit offers.
© 2005 Directed Electronics, Inc.
4
Trouble Shooting v4-1
1988-92
1993-95
1989-94
1997-01
1995-96
1999-02
1997-98
2000-02
1998-99
1997
1995-96
1993-94
1995-97
1999-02
1998
1995-02
1997-02
1994-01
1994-95
1996-00
1998-00
1991-94
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
RED / BLK
RED / BLK
RED / BLK
RED / BLK
BLUE
BLUE
RED/BLK
BLK/RED
RED / BLK
RED / BLK
BLUE
RED / BLK
BLK / WHT
BLK / WHT
BLK / WHT
BLK / WHT
BLK / WHT
BLK / WHT
BLK / WHT
WHITE/GRN
WHT/GRN
BLK / WHT
START
PINK
PINK
PINK
PINK
BROWN
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
BLACK
BLACK
BLACK
BLACK
BLACK
BLK OR BLUE
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLK / YEL
BLK / YEL
BLK / YEL
BLK / YEL
BLK / YEL
BLK / YEL
BLK / YEL
BLACK/YEL
BLK / YEL
BLK / YEL
IGN 1
YELLOW
WHT/BLK
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
BLACK/RED
BLK/RED
YELLOW
IGN 2
Directed Electronics Inc.
1997-02
1984-96
2000-02
1998-99
1986-97
1998-02
1994-97
1997-02
1998-02
1993-97
1996
1995-99
1988-94
1994-96
1996-98
1987
YELLOW
YELLOW
YELLOW
YELLOW
BLK / RED
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
IGN 3/THEFT
ACC
BRAKE LIGHTS TACH
ALARM DISARM
N/A
99+ Transponder
99+ Transponder
99+ Transponder
**LT-GREEN
NO ALARM PRESENT
**LT-GREEN
**LT-GREEN
**LT-GREEN
**LT-GREEN
**LT-GREEN
**LT-GREEN
**LT-GREEN
**LT-GREEN
PARKING LIGHTS HORN
RED / BLACK (+)
RED / BLACK (+)
RED / BLACK (+)
RED / GREEN (+)
RED / BLACK (+)
GREEN / BLACK (+)
GREEN / BLACK (+)
GREEN / BLK (+)
GREEN / RED (+)
GREEN / RED (+)
GREEN / GRAY (+)
GREEN / RED (+)
GREEN/BLACK (+)
GREEN / RED (+)
GRAY / RED (+)
GREEN / BLACK (+)
GRAY / BLACK (+)
RED / GREEN (+)
YELLOW (-)
YELLOW (-)
RED / BLACK (+)
RED/GRN OR RED/BLK
NOTE
© 2005 Directed Electronics, Inc.
***at tach test connector
***at tach test connector
***at tach test connector
***at tach test connector
***under pass seat
***at distributor assembly
**left of steering column
ALARM RELAY IN DRIVER KICK PANEL
**18 pin conn pass kick panel
**behind glove box
GRN / BLK in DKP
BLUE(-)
GRN/BLK(-)
GRN / RED in driver door
BLK / RED(-)***
use valet mode
GREEN / RED**
N/A
**ORANGE / BLACK
**GREEN / BLK(+)
BLUE / RED(-)
BLUE / GRN(-)
BLUE / RED(-)
ORANGE(-)
BLUE / RED(-)
BLUE /GRN(-)
BLUE / RED(-)
N/A
LT GREEN (-)
BLUE / RED(-)
BLUE***
BLUE***
BLUE***
BLUE***
BLUE
BLUE***
BLUE
BLACK/RED
BLK /RED
BLUE
**at theft module in trunk
**at theft module in trunk
**driver kick panel
**in driver kick panel
GRN / WHT(+)
GRN / WHT(+)
GRN / WHT(+)
GRN / WHT(+)
GRN / WHT(+)
GRN / WHT(+)
GRN / WHT(+)
GREEN/YELLOW
GRN / YEL(+)
GRN / WHT(+)
**in driver kick panel
GREEN
GRN / BLUE
BRW / YEL(-)
BRW / YEL(-)
BRW / YEL(-)
BLACK
PPL /WHT or WHT
WHITE
GRN / BLUE
BLK/ GRN
GRY / GRN
GRY/GRN
WHT/BLUE OR GRN
N/A
**BROWN / GREEN
**BROWN / GREEN
**BROWN / GREEN
**GRAY / WHITE
N/A
**BRN / YELLOW
N/A
Equipped with Transponder
**at vaccum motor
**in driver kick panel
WHITE/BLK
YELLOW
WHITE/BLK
WHITE/BLK
WHITE/BLK
WHITE/BLK
WHITE/RED
BLUE
BLUE
WHITE/BLK
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
99+ Transponder
99+ Transponder
BLK/GREEN (-)
**in driver kick panel
**6 cylinder tach ppl/white
PASSKEY III
**in driver kick panel
**in driver kick panel
**in driver kick panel (also equipped with Passlock III)
**in driver kick panel
**in driver kick panel (also equipped with Passlock III)
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
PPL /WHT OR WHT
PPL /WHT
WHITE
WHITE
PPL /WHT OR WHT
WHITE
WHITE OR WHT/BLK
PPL/WHT OR WHT
**BROWN / RED
**BROWN / RED
**in driver kick panel (may be equipped with VATS)
**in driver kick panel (may be equipped with VATS)
**in driver kick panel (may be equipped with VATS)
**6 cylinder tach ppl/white
** see note 238 for passlock bypass
**in driver kick panel
GRN / BLK
BLK/ GRN
BLACK(-)
BLACK(-)
BLACK
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
**in driver kick panel
**in driver kick panel (may be equipped with VATS)
**in driver kick panel
**in driver kick panel (may be equipped with VATS)
**pin 80 of ecm on front of eng comp
**in driver kick panel (also equipped with VATSI)
PASSKEY III
**in driver kick panel
**in driver kick panel (also equipped with VATSI)
**in driver kick panel (may be equipped with VATS)
(also equipped with Passlock III)
Equipped with Passlock II
**in driver kick panel (also equipped with Passkey III)
**in driver kick panel (may be equipped with VATS)
RED / BLACK
RED / BLACK
RED / BLACK
RED / BLUE
RED / BLACK
RED/BLACK
RED / BLACK
RED/BLACK
RED / BLACK
RED / BLACK
RED / BLACK
RED / BLACK
LT-BLUE
BROWN (+)
BROWN/WHITE
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
GRAY / BLACK (-)
LT-BLUE (-)
BROWN (+)
BROWN (+)
BROWN (+)
BLUE OR BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BRW /WHT(-)
BLACK(-)
BLACK (-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK (-)
BLACK(-)
BLACK(-)
N/A
N/A
N/A
WHT / YEL
BLK / YEL
YEL / BLK
YEL / BLK
YEL/BLK
YEL / BLK
YEL / BLK
BLK / YEL
YEL / BLK
N/A
N/A
Transponder
Transponder
N/A
N/A
DK-GRN
WHITE
N/A
N/A
WHITE
N/A
WHITE
WHITE
PPL, BLUE/WHT, OR WHT
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
GRAY / GREEN (+)
BROWN (+)
BROWN/WHT
BROWN (+)
GRAY / BLACK (-)
BROWN (+)
BROWN (+)
BROWN (+)
GRAY / BLACK (-)
BRN OR GRY/BLK (+)
**LT-GREEN
Pulse pink ing 1(+)
**LT-GREEN
**LT-GREEN
LT-BLUE OR WHT (+)
WHT OR PPL/WHT
1
WHITE
Blue Sheet update 2002.xls
(also equipped with VATS)
**in driver kick panel (may be equipped with VATS)
(equipped with passlock II)
(also equipped with VATS)
(1998/01 also equipped with passlock II)
1998+ equipped with passlock II
**in driver kick panel (also equipped with VATS
Equipped with Passlock II
**in driver kick panel (also equipped with VATS
**in driver kick panel (may be equipped with VATS)
**in driver kick panel (also equipped with VATS
(also may equipped with VATS system)
**in driver kick panel (may be equipped with VATS)
**in driver kick panel (may be equipped with VATS)
equipped with Passlock II)
equipped with passlock with passlock II)
Passlock optional in 1995
1998 + Equip w/ Passlock II (95 ign2=pink/white)
1998 + Equipped with Passlock II
Wht or Vio/Wht
WHITE
WHITE
PPL /WHT OR WHT
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
WHITE OR BLUE (+)
LT-BLUE (+)
VATS
VATS
N/A
N/A
N/A
Transponder
N/A
Transponder
N/A
N/A
N/A
VIO /WHT
VIO /WHT
N/A
PASSLOCK
N/A
LT-BLUE (+)
LT-BLUE (+)
BLK / YEL (+)
LT-BLUE (+)
WHITE (+)
LT-BLUE (+)
LT-BLUE (+)
LT-BLUE (+)
WHITE (+)
WHITE (+)
LT-BLUE (+)
LT-BLUE (+)
BLACK (-)
BLACK(-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK (-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
WHITE
WHITE
WHITE
LT-BLUE
LT-BLUE
LT-BLUE
WHITE
LT-BLUE
WHITE
WHITE
WHITE
WHITE
LT-BLUE
WHITE
WHITE
LT-BLUE
N/A
WHITE
BL / WHT
N/A
WHITE
N/A
ORANGE
ORANGE
ORANGE
ORANGE
WHITE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
VIOLET/WHT
WHITE
WHITE
WHITE / BLK
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
Brown/White or Blue
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
**LT-GREEN
**LT-GREEN
**LT-GREEN
**LT-GREEN
**BRN/PPL(-)
**LT-GREEN
LT-GREEN
**LT-GREEN
**LT-GREEN
**LT-GREEN
VATS
VATS
N/A
VATS
Transponder
VATS
N/A
VATS
VATS
PPL / WHT
Passlock II
N/A
Transponder
VATS
WHITE (96+)
N/A
WHITE (96+)
ORANGE
ORANGE
N/A
N/A
N/A
WHITE
WHITE
WHITE
N/A
N/A
N/A
WHITE
N/A
Dk-Green
N/A
ORANGE
ORANGE
PPL OR WHITE
BL/WHT OR PPL/WHT
N/A
N/A
N/A
N/A
N/A
N/A
**LT-GREEN
**LT-GREEN
N/A
N/A
N/A
N/A
**LT-GREEN
**LT-GREEN
N/A
**LT-GREEN
NO ALARM PRESENT
**LT-GREEN
**LT-GREEN
N/A
N/A
N/A
N/A
N/A
N/A
WHITE
WHITE
WHITE
WHITE
**GREEN
WHITE
PURPLE/WHT
WHITE
WHITE
WHITE
VIO / WHT
N/A
N/A
N/A
RED
LT-BLUE
WHITE
N/A
LT-BLUE
BL / WHT
WHITE
WHITE
LT-BLUE
N/A
See Note
N/A
See Note
N/A
N/A
VATS
N/A
N/A
Passlock II
PASSLOCK
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
LT-BLUE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
LT-BLUE (+)
WHITE (+)
PURPLE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
PPL / WHT
WHT OR BLU
WHT OR BLU
LT-BLUE (+)
WHITE (+)
WHITE (+)
DK-GREEN
GREEN
WHITE
N/A
VATS
VATS
See Note
VATS
Passlock II
VATS
N/A
N/A
VATS
VATS
Passlock II
VATS
See Note
ORANGE
ORANGE
ORANGE
BROWN
BROWN
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
BLK/YEL OR YEL/BLK
YEL / BLK
YEL / BLK
1993
1990-96
1992-93
1992-94
1997-02
1995-99
2000-02
1994
1995-02
1986-89
1999-01
1999-02
1998-02
1992-97
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
VIOLET
YELLOW
YELLOW
YELLOW
VIOLET
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YEL OR PPL
1996-02
1994-96
1995-01
1994
1978-94
1982-02
1994-96
1981-96
2000-02
1996-99
1995
1987-96
1997-02
1987-96
1997-02
1994-96
2000-02
1996-99
1995-96
1990-94
95-00
1990-94
1997-02
1995-02
1995-02
Make/model Year
ACURA
AUDI
2.5TL
3.2TL
3.2TL
3.5RL
CL
Integra
Legend
SLX
SLX
Vigor
80
90
100
A4
A4
A6
A6
A8
A8
A8
Cabriolet
S4
BUICK
Century
Century
Lesabre
Lesabre
Lesabre
Park Avenue
Park Avenue
Park Avenue Ultra
Regal
Regal
Regal RWD
Riviera
Riviera
Roadmaster
Skylark
Summerset
Cadillac
Chevrolet
Allante
Fleetwood (RWD)
Coupe DeVille
Eldorado
Catera
Concours
DeVille
DeVille
Eldorado
Eldorado
Escalade
Escalade
Seville SLS STS
Seville
Astro
Beretta / Z26
Blazer
Blazer
Blazer Full Sise
Camaro,Z28
Caprice
Caprice
Cavalier
Cavalier
Cavalier
Corsica
Corvette
Corvette
Express
Impala
Impala (fwd)
Impala SS
Lumina APV
Lumina APV
Lumina Sedan
Lumina Sedan
Malibu
Monte Carlo
Pick-up Full size
Directed Electronics Inc.
IGN 2
IGN 3/THEFT
ACC
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE
WHITE
WHITE
WHITE
WHITE
VIOLET/WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
BRAKE LIGHTS TACH
IGN 1
WHITE / TAN(+)
START
Make/model Year
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
WHT OR WHT/TAN
WHITE/TAN (+)
WHITE/TAN (+)
GREEN (+)
GREEN (+)
WHITE / TAN
WHITE(+)
WHITE / TAN
WHITE / TAN(+)
WHITE / TAN(+)
GREEN
WHITE/BLK
GRAY/BLUE
BLK / GRAY
WHITE
WHITE
WHITE(+)
GRAY / BLK
BLK / GRAY
TAN / PINK
RED
BLK / GRAY
BLK / YELLOW
TAN/RED
GRAY / BLU
GRAY / BLU
TAN/RED
GRAY
GRAY
BLK / GRAY
BLK / GRAY
WHT / BLK
WHT OR WHT/RED
BLK / GRAY
GRAY / BLU
WHT / BRW
D BLUE/TAN
BLACK/GRAY
WHITE
WHITE/TAN (+)
WHITE / TAN
WHITE / TAN
WHITE / TAN
WHITE / TAN
WHITE / TAN
WHITE
WHITE
GREEN
GRN/ORG
WHITE / TAN(+)
WHITE
L.GREEN/RED
GREEN/RED
YEL/DK-BLUE
WHITE/PINK
WHITE/PINK
TAN/YELLOW
BLU/GRN
RED/GREEN
WHITE/PINK
ORANGE/WHT
TAN/YELLOW
GREEN
WHT OR WHT/TAN
BLK/ORANGE
BLK/WHITE
BLUE
BLUE
BLK / ORNG
BLACK/WHITE
BLK / ORNG
BLK / ORG
BLK / ORG
BLK / ORG
BLK / RED
BLK/WHT & BLUE
BLACK/WHITE
BLACK/WHITE
BLU&BLK/WHT
BLACK/WHITE
BLACK/WHITE
BLK / ORG
BLK / ORG
BLUE
BLUE/BLK
BLK / WHT
BLK / ORG
BLK/LGRN(+)
L GREEN (+)
L GREEN (+)
GREEN
L GREEN (+)
ORNG/YELLOW
LT-GREEN
LT-GREEN
L GREEN (+)
L GREEN (+)
GREEN (+)
GREEN
DK-GREEN
BLK/LGRN(+)
L GREEN (+)
L GREEN (+)
L GREEN (+)
L GREEN (+)
L GREEN (+)
RED/LT-GREEN
GREEN OR RED/GRN
WHT/GREEN
2
L GREEN (+)
TAN/YELLOW
TAN/YELLOW
WHITE
TAN/YELLOW
WHT/BLACK
TAN/LT-GREEN
TAN/YELLOW
TAN/YELLOW
RED/BLACK
BLK/LGRN(+)
BLK/LGRN(+)
GREEN
BLK/LGRN(+)
YELLOW
BLK/GRN
BLK/GRN
BLK/LGRN(+)
BLK/LT.GRN
BLACK/WHITE
RED/BLUE
BLK/WHT
RED/BLACK
BLK/LGRN(+)
BLK/LGRN(+)
GRN/LTGRN
BLK/LGRN(+)
BLK/LGRN(+)
BLK/GRN
BLK/GRN
BLUE/YEL
WHITE / TAN(+)
WHITE / TAN(+)
WHITE / TAN(+)
WHITE / TAN(+)
WHITE / TAN(+)
WHITE / TAN(+)
WHITE / TAN(+)
WHITE / TAN(+)
WHITE / TAN(+)
WHITE / TAN(+)
WHITE / TAN(+)
WHITE / TAN(+)
WHITE/TAN (+)
GREEN (+)
WHITE / TAN(+)
WHITE/BLK
WHITE/TAN (+)
WHITE/TAN (+)
WHT / BRN
BLK / GRAY
N/A
See Note
N/A
See Note
N/A
See Note
N/A
See Note
See Note
N/A
See Note
YELLOW
YELLOW
VIOLET
YELLOW
YELLOW
YELLOW
Violet or Yel
YELLOW
YELLOW
Violet or Yel
YELLOW
N/A
N/A
2ND GRY/YEL
RED/BLACK
2ND GRY/YEL
N/A - Transponder
2ND GRY/YEL
2ND GRY/YEL
GRAY/YEL
GRAY/YEL
N/A
N/A
N/A - Transponder
2ND GRY/YEL
2ND GRY/YEL
2ND GRY/YEL
N/A
2ND GRY/YEL
TRANS-99 +
GRAY/YEL
GRAY/YEL
2ND GRY/YEL
N/A
TRANS-99+
TRANSPONDER
N/A
N/A
N/A
N/A
N/A
GRN&ORG-Trans
N/A
N/A
N/A
N/A
N/A
N/A
N/A
**TRANSPONDER
N/A
**TRANSPONDER
N/A
ORANGE
N/A
N/A
N/A - Transponder
N/A - Transponder
N/A
WHITE 96+
N/A
WHITE 96+
N/A
WHITE 96+
N/A
WHITE 96+
WHITE
N/A
WHITE
1988-94
1995-02
1986-94
1995-02
1986-94
1995-02
1992-94
1995-02
1995-01
1985-94
1997-02
Chrysler
Pick-up Full size
Pick-up S-10
Pick-up S-10
S-10 Blazer
S-10 Blazer
Suburban
Suburban
Tahoe
Van
Van
Venture
GRN / RED
GRN/RED
GRN / RED
RED / WHT
RED / WHT
N/A
N/A
N/A
N/A
GRN / RED
RED / WHT
RED / WHT
RED / WHT
RED / WHT
GREEN/RED
BLU / BLK
N/A
N/A
GREEN/RED
BLK/ORG
Dodge
300M
Cirrus
Concorde
Concorde
Concorde
Imperial
Le Baron Coupe
LeBaron Conver.
Lebaron Sedan
LHS
LHS
LHS
New Yorker
New Yorker
Sebring
Sebring
Sebring Conver.
Town & Country
Town & Country
Town & Country
TAN /PINK
BLK / GRAY
TAN /PINK
RED
RED / YEL
BLK / GRAY
BLK / GRAY
BLK / GRAY
GRAY / BLU
TAN /PINK
RED
GRAY
RED
GRAY
BLUE / WHT
BLUE
BLUE / WHT
BLUE
BLUE
BLUE
BLUE
BLUE
BLUE
BLUE / WHT
BLUE
BLUE
BLUE
BLUE
BLUE
BLK / WHT
BLUE
PINK/WHT
BLUE
BLUE
BLUE / BLK
N/A
Transponder
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Transponder
N/A
N/A
N/A
N/A
N/A
N/A
N/A
BLK / WHT
PINK/WHT
DGRN/RED
BLK/ORG
BLUE / BLK
BLUE / BLK
Grn/Red 99+
BLK/ORNG
Grn/Red 99+
GRN / RED
RED / WHT
N/A
N/A
GREEN
BLACK/ORG
BLACK/ORG
RED
BLACK/ORG
BLACK/ORG
N/A
N/A
BLUE / BLK
BLUE/RED
BLK/ORG
N/A
FORD
BLK / ORG
BLK / ORG
BLK / ORG
BLK / ORG
BLK / ORG
BLK / ORG
BLK / ORG
BLK / ORG
BLK / ORG
BLK / ORG
BLK / ORG
BLK / ORG
BLK / ORG
BLK / ORG
BLK/ORG &BLK/WHT
BLUE
BLK / ORG
N/A
BLK/ORANGE
BLK/WHITE
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
BLK / RED
YELLOW
YELLOW
YELLOW
YELLOW
BLUE
BLUE
BLK / WHT
BLK / WHT
BLUE
BLUE
BLUE
BLUE / WHT
BLUE
BLUE
BLUE
BLUE
BLUE
BLUE
BLUE
BLUE
BLUE
BLUE
BLUE
BLK / WHT
DK GREEN
BLUE
BLUE
RED/BLACK
GRAY/YEL
GRAY/YEL
BLK/RED
GRAY/YEL
N/A
PINK/BLK
BRW/PINK
GRAY/YEL
N/A
BLACK/RED
RED/GRN
BLK/RED
RED/BLACK
GRAY/YEL
GRAY/YEL
N/A
BLACK/RED
GRAY/YEL
RED/BLACK
GRY/YEL
BLK/RED
N/A
N/A
1995-99 BLK / RED
2001-02 YELLOW
1999-02
1995-99
1998-02
1996-97
1993-95
1990-95
1990-94
1990-95
1993-94
1999-02
1994-98
1994-95
1996-97
1994-95
2001-02
1995-99
1996-99
2001-02
1996-00
1991-95
YELLOW
YELLOW
BLK / YEL
BLK / YEL
BLUE / YEL
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
BLUE / YEL
YELLOW
YELLOW
YEL / BRN
YELLOW
YELLOW
YELLOW
BLK / YEL
BLK/RED
YELLOW
YELLOW
RED/BLACK
RED/L GRN
RED/L GRN
BLUE
RED/L GRN
GREEN
BRW/PINK
RED/GREEN
RED/L GRN
LGRN/PURP
BLUE
GRY/YEL
DK-BLUE
RED/BLACK
DBLUE/GRN
LGRN/PURP
RED/GRN
DBLUE/GRN
RED/BLACK
RED/GREEN
TAN/WHT
BLK/PINK
BLUE
Avenger
Caravan
1996-00
1991-95
1996
1995
1997-02
1992-96
1998-02
1998-02
1996-97
1995-02
1987-90
2002
1997-01
1994-96
2002
1998-02
1992-98
1991-94
1989-94
1991-95
2001-02
1995-99
1995-02
RED/BLUE
WHITE/PINK
WHITE/PINK
WHITE
RED/BLUE
GRY/WHT
WHT/PINK
WHT/PINK
WHITE/PINK
TAN/LT.BLU
RED/WHT
BLK/GRN
BLK/BLUE
RED/BLUE
RED/BLUE
RED/BLUE
RED
RED/BLUE
RED/BLUE
WHT/PINK
WHT/PINK
GREEN
N/A
Caravan
Caravan
Colt
Colt
Dakota
Dakota
Durango
Intrepid
Intrepid
Neon
Omni
Ram Pick-up
Ram Pick-up
Ram Pick-up
Ram Pick-up
Ram Van Wagon
Ram Van Wagon
Shadow
Spirit
Stealth
Stratus
Stratus
Viper
2000
1992-98
1996-98
1994-98
1992-96
1995-00
1995-02
>1994
1992-01
2001-02
1999-02
1997-98
1994-96
2001-02
1997-02
1991-01
2002
1994-02
1994-02
1998-02
1994-98
1996-97
Excursion
Aerostar
Areomax
Aspire
Bronco
Contour
Crown Victoria
Crown Victoria
Econoline
Escape
Escort zx2
Escort
Escort
Excursion
Expedition
Explorer
Explorer
F-150 / F-250
F-250 / F-350
Mustang
Mustang
Probe
*LT-GREEN / ORANGE(+)
N/A
DISARMS WITH UNLOCK
WHITE/RED (-)
N/A
N/A
N/A
**BLACK / ORNG (-)
N/A
**GREEN / ORNG (-)
**GREEN / ORANGE (+)
**WHITE (-)
N/A
N/A
LT.GREEN/ORG (-)
**GREEN / ORNG (-)
N/A
LT.GREEN/ORG
**BLACK / ORNG (-)
N/A
N/A
N/A
*LT-GREEN (-)
**GREEN / WHT
VIOLET/Light BLUE
GREEN / ORANGE
VIOLET/Light BLUE
WHITE/RED (-)
N/A
**GREEN / ORANGE (+)
**GREEN / ORANGE (+)
**GREEN / ORANGE (+)
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
ORANGE / BLACK (-)
ALARM DISARM
BROWN (+)
BROWN (+)
BROWN (+)
RED/BLACK (+)
BROWN (+)
RED/BLUE (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
RED/BLACK (+)
RED/BLACK (+)
RED/BLACK (+)
BROWN (+)
BROWN (+)
WHITE/BLACK (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN +
BROWN (+)
ORANGE
BLACK / YELLOW (+)
BLUE OR TAN (+)
GRN/WHT OR PNK/BLK
L GREEN/RED (-)
BLACK/YELLOW (+)
GREEN / WHITE (+)
GREEN / WHITE (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
PURPLE/YELLOW
BLACK / YELLOW (+)
BLACK / YELLOW (+)
PUR/YEL
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
GRN/WHT OR ORG (+)
GREEN / WHITE (+)
RED/BLACK (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK / YELLOW (+)
BLACK/YELLOW (+)
GREEN / WHITE (+)
BLACK / YELLOW (+)
RED/BLK
BLACK/YELLOW (+)
BLACK/YELLOW (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
YEL/L GREEN (-)
YEL/LGREEN
YEL/LGREEN
RED/GRN (-)
DARK BLUE (-)
BLK/BLUE (-)
YEL/GREEN (-)
YEL/GREEN (-)
YEL/L GREEN (-)
YEL/L GREEN (-)
GREEN/ORG (-)
GRN/ORNG (-)
GRN/ORG
YEL/L GREEN (-)
D BLUE (-)
BLACK (-)
YEL/GREEN
YEL/LGREEN (-)
YEL/LGREEN (-)
PPL/ORNG (-)
YEL/LT-GRN
GRN/ORNG (-)
BLACK/RED (-)
BLACK/RED (-)
GRN / RED(-)
GRN / BLK (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK/RED (-)
BLK / RED (-)
BLK / RED (-)
BLK/RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
GRN / BLK (-)
GRN/BLK (-)
BLK / RED (-)
BLK / RED (-)
GRN / RED(-)
GREEN/BLK (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK / RED (-)
BLK/RED (-)
GRN / RED(-)
BLK / RED (-)
GREEN/BLK (-)
BLACK (-)
BLACK/RED
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
BLACK(-)
PARKING LIGHTS HORN
**GREEN/ORG OR GRN/WHT (-)
**GREEN / ORANGE (-)
N/A
N/A
N/A
N/A
**GREEN / ORANGE (+)
**GRN / ORG OR WHT (-)
**GREEN / ORANGE (-)
**GREEN / ORANGE (-)
**GREEN / ORANGE (-)
LT.GREEN/ORANGE (-)
**GRN/ORG OR WHITE (-)
D.GREEN/PURPLE (-)
N/A
N/A
N/A
N/A
N/A
May equipped with transp
N/A
D.GREEN/PURPLE (-)
LT.GREEN/BLK
N/A
N/A
N/A
D.GREEN/PURPLE (-)
D.GREEN/PURPLE (-)
D GREEN/PURPLE (-)
D GREEN/PURPLE (-)
GREEN/VIOLET
D GREEN/PURPLE (-)
N/A
DK-GREEN/PPL
N/A
NOTE
© 2005 Directed Electronics, Inc.
(1998/01 also equipped with passlock II)
(1998/01 also equipped with passlock II)
(1998/01 also equipped with passlock II)
(1998/01 also equipped with passkey III
(1998/01 also equipped with passlock II)
(1998/01 also equipped with passlock II)
**equipped with transponder key
Optional tranponder key in late model
**in driver kick panel
**in driver kick panel
**in driver kick panel
**equipped with transponder key
**in driver kick panel
**in driver kick panel
**in driver kick panel
**equipped with transponder key
**in driver kick panel
**late model are equipped with transponder key
( note: this vehicle needs 180 ohm resistor on 2nd starter wire)
**in black 20 pin connector driver kick panel
on second starter wire)
( note: this vehicle needs 180 ohm resistor
**12 pin blk connector behind driver dash
Late Model Require resistor value to Disarm
2000+ are equipped with Transponder key
**at fact keyless mod on top of dash
2000+ are equipped with Transponder key
**24 pin conn behind driver dash
NOTE: needs 1.4K ohm resistor for parking liths
**12 pin blk conn-driver kick pan. (1998=Yel/Brwn)
**in driver kick panel
*back of fuse junction block 270 Omhs resistance …
..for disarrm needed
Equipped with Transponder
Equipped with 2 GRAY/YEL external relay is required
Equipped with 2 GRAY/YEL external relay is required
Equipped with Transponder
98 & UP MAY equipped WITH TRANSPONDER KEY.
Equipped with Transponder
Equipped with Transponder
Equipped with Transponder from 1998+
Equipped with Transponder from 1998+
equipped with transponder/use relay for ing 3
96 & UP MAY equipped WITH TRANSPONDER KEY.
Blue Sheet update 2002.xls
1995-99
1994-99
1995
1989-98
1995-02
1996-02
1992-95
1994-97
1999-02
1996-98
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
RED/ YEL
BLK / WHT
BLK / WHT
BLACK/YEL
RED/BLUE
RED/BLUE
WHT/PINK
RED/BLUE
GREEN
RED/BLUE
START
Lt-Green
BLK/YEL
BLK/YEL
BLK/YEL
BLK/YEL
BLK/YEL
BLK/YEL
BLK/YEL
BLK/YEL
BLACK/RED
BLK/YEL
BLK/YEL
BLK/YEL
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
BLK/WHITE
BLUE / BLK
BLACK
LGRN/PURP
RED/GREEN
RED/GREEN
RED/GREEN
WHITE/YEL
RED/LT.GRN
IGN 1
YELLOW
BLUE/WHITE
BLK/WHITE
RED
BLUE/RED
BLUE
ORANGE
BLUE/WHT
N/A
Gray
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
WHITE
YELLOW
BLK/YEL
N/A
YELLOW
YELLOW
WHITE
WHITE
WHITE 95+
WHITE 95+
WHITE
WHITE 95+
WHITE
WHITE 95+
ORANGE
WHITE
ORANGE
WHITE
WHITE
ORANGE
WHITE 96+
RED/GRN
BLK / YEL
BLK/YEL
YEL/BLACK
GRAY/YEL
GRAY/YEL
GRAY/YEL
GRAY/YEL
BLACK
BLK/LGRN
IGN 2
See Note
See Note
N/A
N/A
N/A
N/A
N/A
See Note
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
See Note
See Note
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N-A
N-A
N-A
N/A
2ND GRY/YEL
RED/BLK
GRAY/YEL
GRAY/YEL
VIO/ORNG
2ND GRY/YEL
IGN 3/THEFT
BLUE
BLUE
BLUE
BLUE
BLUE
ORANGE
ORANGE
WHITE/BLK
WHITE/BLK
WHT/BLK
BLUE
BLUE
BLUE
BLUE/BLK
BLUE
BLUE
WHT/BLUE
N-A
WHT/BLUE
WHITE/BLUE
WHITE/BLUE
WHT/BLUE
BLACK/RED
WHITE/RED
BLUE
BLUE
RED/YELLOW
WHITE/BLUE
BLUE
BLUE
RED/WHITE
YELLOW
BLUE
BLUE/WHT
BROWN
BLK/WHT
N/A
Orange
WHT/BLK
WHT/BLK
WHT/BLK
WHT/BLK
WHT/BLK
WHT/BLK
WHT/BLK
WHT/BLK
BLUE/BLACK
BLUE OR BLK
WHT/BLK
WHT/BLK
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
BROWN
ORANGE
BROWN
ORANGE
ORANGE
BROWN
ORANGE
BLUE / RED
BLUE / RED
BLUE
BLK/RED OR BLU/RED
BLK/LGRN(+)
BLK/GRN
BLK/GRN
BLK/GRN
BLACK/GRN
BLACK/PINK
ACC
RED
GREEN/YELL
GREEN/YELL
RED
RED
VIOLET
WHITE(+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
RED
GREEN/YELLOW
GREEN/YELLOW
GREEN/YELLOW
GREEN/YELLOW
RED
RED/GREEN (+)
GRN/RED
RED/GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
PURPLE (+)
RED/YELLOW(+)
RED/GREEN (+)
RED/GREEN (+)
GREEN/YELLOW
GREEN/YELLOW
PINK/BLACK
GRENN (+)
GREEN/BLACK(+)
WHITE
GREEN/BLACK(+)
GREEN (+)
LT-BLUE (+)
GREEN(+)
GREEN/WHITE
Red
GREEN/WHITE
GREEN/WHITE
GREEN/WHITE (+)
GREEN/WHITE
WHT/BLK
GREEN/WHITE (+)
GREEN/WHITE (+)
WHT/BLK
RED (+)
RED (+)
GREEN/WHITE
GREEN (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
GREEN / WHT
WHITE (+)
GREEN / WHT
GREEN/WHITE (+)
L GREEN (+)
RED/LT-GREEN
RED/LT-GREEN
LT-GREEN
RED/GREEN (+)
RED/GREEN (+)
BLACK/RED
BLACK/RED
BLACK/RED
WHITE
BLK/RED
WHITE
WHITE
BLUE
BLUE
BLUE
BLACK/RED
BLACK/RED
BLACK/RED
BLACK/RED
BLK/RED
BLACK/RED
BLACK/GREEN
BLUE/GREEN
WHITE/GREEN
WHITE
WHITE/GREEN
BLU/BLK
WHITE
WHITE/GREEN
WHITE/GREEN
WHITE/GREEN
BLUE/WHITE
BLUE OR BROWN
BLUE/RED
WHITE
BLUE
WHITE
WHITE
WHITE
WHITE
N/A
BLUE
BLUE
BLUE
BLUE
BLUE
BLUE
BLUE
BLUE
BLACK/RED
BLUE(2.6L)*
BLUE
BLUE
WHITE/VIOLET
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
VIOLET/WHITE
WHITE
WHITE
WHITE
BROWN
WHITE
BLACK(-)
BROWN
BLUE/GREEN
WHITE/PINK
BRAKE LIGHTS TACH
YELLOW/BLUE
BROWN/RED
ORANGE/BLACK(-)
N/A
BLUE/YELLOW (-)
N/A
N/A
BLACK/RED (-)
N/A
N/A
YELLOW/BLUE
BROWN/RED
ORANGE/BLACK(-)
BLUE/YELLOW (-)
N/A
N/A
ORANGE/BLUE
N-A
GREEN/YELLOW (-)
GREEN/YELLOW (-)
GREEN/YELLOW (-)
GREEN/YELLOW (-)
GREEN/RED (-)
LT-GREEN/RED (-)
SKY BLUE (-)
SKY BLUE (-)
LT. GREEN (-)
LT. GREEN (-)
N/A
N/A
N/A
N/A
N/A
N/A
LT-GREEN/BLACK (-)
N/A
N/A
Red/Yel 98+ blue dr door
N/A
N/A
N/A
BLUE
N/A
WHITE/RED (-)
BLUE
N/A
N/A
N/A
N/A
WHITE
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
GREEN (-)
N/A
N/A
N/A
N-A
N-A
N-A
N/A
D GREEN/PURPLE (-)
PINK/WHITE
N/A
DK-GREEN/PPL
BLUE/BLACK (-)
D GREEN/PURPLE (-)
ALARM DISARM
GREEN/RED (+)
YELLOW
GREEN (-)
GREEN/RED (+)
GREEN/RED (+)
LT-BLUE (-)
BROWN (+)
RED/BLACK (+)
RED/BLACK (+)
RED/BLACK (+)
GREEN/RED (+)
YELLOW (-)
GREEN(-)
GREEN/RED (+)
GREEN/RED (+)
YELLOW (-)
RED/BLUE (+)
RED/BLUE (+)
RED/BLUE (+)
RED/GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
WHITE/BLUE (+)
YELLOW/RED (-)
RED/YELLOW (+)
RED/YELLOW (+)
PINK/BLUE (+)
PINK/BLUE (+)
GREEN (-)
RED/BLACK (+)
N/A
BLUE (-)
GREEN/WHITE (+)
GREEN/WHITE (+)
LT-BLUE
GREEN/WHITE (+)
N/A
RED/BLACK (+)
RED/BLACK (+)
RED/BLACK (+)
RED/BLACK (+)
RED/BLACK (+)
RED/BLACK (+)
RED/BLACK (+)
RED/BLACK (+)
GREEN/PINK (-)
GREEN/RED (+)
RED/BLACK (+)
RED/BLACK (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
GREEN
RED/YELLOW (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BLACK/GREEN
WHITE/BLACK (+)
BLUE/RED (-)
L GRN/BLUE (-)
L GRN/BLUE (-)
GREEN (-)
GREEN (-)
BLK/ORANGE(-)
BLK/ORANGE(-)
GREEN/WHT(-)
GREEN (-)
GREEN/WHITE
N/A
GRN/WHITE (-)
GRN/WHITE (-)
GRN/WHITE (-)
GRN/WHITE (-)
GRAY/YEL (-)
GREEN/RED (-)
WHITE/GRN (-)
WHITE/GRN (-)
LT. GRN/BLACK
LT. GRN/BLACK
BLUE/ORANGE
BLK/WHITE (-)
BLK/WHITE (-)
RED
BLK/WHITE (-)
BLK/WHITE (-)
YELLOW (-)
GRN/BLK (-)
N/A
BLUE
BLUE/RED (-)
GRAY
BLUE/RED (-)
L GRN/BLUE (-)
L GRN/BLUE (-)
L GRN/BLUE (-)
L GRN/BLUE (-)
D GREEN (-)*
BLK/ORANGE(-)
N/A
BLUE/BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLUE / BLK(-)
GRN / RED(-)
GRN / RED(-)
BLACK (-)
YEL/LGREEN (-)
Ppl or Grn/Orang
YEL/LT-GRN
DK-BLUE
GRN/ORNG (-)
YEL/LT. BLUE (-)
PARKING LIGHTS HORN
Directed Electronics Inc.
1999-02
1999-02
1985-95
1985-97
1998-01
1986-02
1996-02
1996-02
1987-95
1996-02
1991-95
2000-02
1996-98
1992-95
1992-99
BLK/WHT
BLK/WHT
BLK/WHT
BLK/WHT
BLK/WHT
BLK/WHT
BLK/WHT
BLK/WHT
WHT/BLUE
BLK/WHT
BLK/WHT
BLK/WHT
GREEN
BLACK/WHT
WHITE/BLUE
RED
BLK/WHT
BLK/WHT
PINK
RED/BLACK
BLK/WHT
RED/YELL
BLUE
N/A
RED
RED
RED/YEL
N/A
N/A
N/A
N/A
WHT/BLUE
RED/YEL
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
3
WHT/PNK OR ORG/WHT*
TAN/YELLOW
TAN/YELLOW
TAN/YELLOW
1992-98 Drk Green
1994-02
1994-02
1997-01
1995-98
1999-02
1996-98
1995
1998-02
1996-98
1995
1997-02
1987-96
WHITE
BLUE/YEL
YEL/RED
WHITE
BLK/YEL
BLACK/YEL
YELLOW
YEL/RED
YEL/RED
BLACK/RED
BLK/WHT
BLACK/RED
BLACK/RED
BLACK/RED
BLACK/RED
WHITE/BLK
BLK/RED
BLK/WHT
BLK/WHT
BLK/WHT
BLK/YEL
BLACK/RED
BLACK/RED
BLACK/RED
N/A
BLLK/YEL
WHITE
WHITE
YELLOW
YELLOW
YELLOW
BLACK/RED
BLACK/RED
BLACK/RED
BLACK/RED
BLACK/RED
BLACK/RED
BLK/ORG OR BLK
2000-02
1999-00
1995-98
2001-02
1991-00
1991-95
1999-02
1989-98
1997-02
BLK/WHT
BLK/YEL
BLK/WHT
BLK/BLUE
BLK/BLUE
BLK/GRN
BLACK/YEL
BLK/WHITE
BLK/RED
BLK/RED
BLK/YEL
BLK/WHT
BLACK/YEL
BLACK/YEL
BLACKYEL
BLACK/YEL
BLK/RED
PINK
PINK
BLACK/YEL
BLACK/YEL
BLACK/YEL
BLACK/YEL
BLACK/YEL
BLK/YEL
BLK/GRN
BLK/YEL
BLACK/YEL
White (+)
2002
1999-02
1991-97
2000-01
1998-00
1996-98
1993-97
1999-02
1997-98
1990-96
2001-02
1996-00
BLACK/WHT
BLK/WHT
BLK/WHT
BLACK/WHT
BLK/WHT
YELLOW
YELLOW
BLACK/WHT
BLK/WHITE
BLACK/WHT
BLACK/WHT
BLACK/WHT
BLK/WHT
WHT/GRN
BLK/WHT
BLACK/WHT
DK-GREEN (-))
GREEN (-)
BLK/ORANGE(-)
GREEN/RED (-)
ORANGE (-)
BLACK (-)
1998-00
1999-02
1996-98
1990-94
2001-02
1999-02
1996-97
1999-02
1996-00
1996
1998-02
1999-02
1996-98
1994-95
1992-93
1999-02
Make/model Year
GEO
Ranger
Taurus
Taurus
Thunderbird
Windstar
Windstar
GMC
Metro
Prizm
Prizm
Tracker
Denali
Envoy Series
G Serie Van
Jimmy
Jimmy S-15
Safari
Savana
Sierra
Sierra
Sonoma
Sonoma
Suburban
Suburban
Suburban
Yukon / Tahoe
Honda
Hummer
Accord
Civic
CRV
Delsol
Odyssey
Odyssey
Odyssey
Passport
Passport
Passport
Prelude
Prelude
Hyundai
General Hummer
Accent
Accent
Accent
Elantra
Elantra
Scoupe
Sonata
Sonata
Tiburon
Infinity
Isuzu
I30
G20
G20
I30
I30
I30
J30
Q45
Q45
Q45
QX4
QX4
Amigo
Isuzu Trooper
Isuzu Trooper
Amigo
Axiom
Hombre
Hombre
Oasis
Oasis
Oasis
Rodeo
Trooper
Trooper
Trooper
Trooper
Vehicross
NOTE
© 2005 Directed Electronics, Inc.
Equipped with Transponder
96 & UP MAY equipped WITH TRANSPONDER KEY.
Equipped with 2 or 3 GRAY/YEL external relay is required
Require 50 Ohms resistor with parking light
2GRY/YEL EXT RELAY REQ, TACH ALSO TAN/YEL
1998 + Equipped with PASSLOCK II
1998 + Equipped with PASSLOCK II
1998 + Equipped with PASSLOCK II
1998 + Equipped with PASSLOCK II
1998 + Equipped with PASSLOCK II
1998 + Equipped with PASSLOCK II
1998 + Equipped with PASSLOCK II
1998 + Equipped with PASSLOCK II
1998 + Equipped with PASSLOCK II
Many 98+ are equipped with transponder key
Many 98+ are equipped with transponder key
1999 + Equipped with Transponder
2000 + Equipped with Transponder
1999 + Equipped with Transponder
96-97 Horn wire is ORG/BLK (-)
*3.2L wire is BLK/RED
98+ are equipped with transponder key
Tach at PCM pin 47 left side of dash.
Equipped with Transponder
N/A
May have Transponder
2Th start wire white/green. May have Transponder
2Th start wire black/red, transponder equipped
May have Transponder
2000 + Equipped with Transponder
1998 + Equipped with Passlock II
Alarm disarm wire in driver door
Blue Sheet update 2002.xls
1994-98
1995-98
1999-00
1999-02
2000-02
1997-01
1993-95
1991-92
1999-02
1996-98
1993-95
2002
1997-02
1993-96
1991-92
RED
BLACK/WHT
BLACK/WHT
BLACK
BLK/BLUE
BLACK/RED
BLACK/RED
RED
BLACK/WH
BLACK/WHT
BLACK/WHT
BLACK/WHT
BLK/WHITE
BLK/BLUE
BLACK/WHT
BLACK/YEL
BLK/YEL
RED
BLACK/RED
BLACK/YEL
YELLOW
YELLOW
GREEN
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YEL/BLUE
START
BRWN/PINK
RED/LT GRN
GREEN/BLK
WHT/YEL
D BLUE/GRN
WHITE/YEL
BRWN/PINK
BLACK/RED
BLACK/ORG
BLACK/ORG
BLACK/YELLOW
BLACK/ORG
BLACK/ORG
BLACK/ORG
BLACK/ORG
BLACK
BLACK/RED
BLACK/BLUE
BLKACK/YEL
BLACK/ORG
BLACK/ORG
BLACK/ORG
BLACK/WHT
BLK/WHT
YELLOW
BLACK/YEL
WHITE/BLUE
D BLUE
D BLUE
YELLOW
D BLUE
D BLUE
D BLUE
D BLUE
BLUE/GRAY
BLUE/GRAY
IGN 1
ORANGE
BLACK/RED
BLACK/RED
BLACK/RED
BLACK/RED
GRAY/YEL
BLACK/RED
BLACK/RED
BLACK/RED
RED/BLK
N/A
BLACK/RED
BLACK/RED
BLACK/RED
N/A
BLACK/RED
BLACK/RED
GRAY/YEL
BLACK/RED
BLACK/YEL
GRAY/YEL
GRAY/YEL
YELLOW
BLACK/YEL
GRAY/YEL
GRAY/YEL
PINK/BLACK
BLACK/YEL
BLACK/YEL
BLACK/YEL
BLACK/WHITE
BLACK/YEL
BLACK
BLACK
BLACK/YEL
RED/WHITE
BLACK/YEL
BLACK/RED
BLACK/WHT
BLACK/YEL
BLACK/YEL
BLACK/YEL
BLUE/RED
BLUE
BLUE
BLK/WHT
WHITE
BLACK/ORG
BLACK/ORG
VIOLET
BLK/ORANGE
ORANGE
ORANGE
BLACK/ORG
BLACK/ORG
ORG/BLK
IGN 2
N/A
N/A
N/A
N/A
N/A
2GRAY/YEL
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
2GRAY/YEL
N/A
N/A
GRAY/YEL
N/A
PINK/YEL
D GRN/YEL
RED/BLACK
PINK/BLK
BLK/GREEN
Transponder
N/A
N/A
See Note
N/A
N/A
See Note
N/A
N/A
N/A
N/A
N/A
N/A
N/A
See Note
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
IGN 3/THEFT
GRAY
BLUE
BLK/WHITE
GREEN/RED
BLK/WHITE
BLUE
BLACK/LGRN
BLK/WHITE
BLUE
BLUE
N/A
BLUE
BLUE
BLACK/LGRN
BLUE
BLUE
BLUE
BLACK/RED
BLACK/RED
BLK/LT.GRN
BLK/LT.GRN
PINK/WHT
BRN/ORG
BLACK/LGRN
BLK/LT.GRN
RED/GREEN
BLUE/RED
PINK/BLUE
PINK/BLUE
BLUE/YELLOW
YELLOW
WHITE/GRN
WHITE/GRN
PINK/BLUE
WHITE/GREEN
BLUE/RED
BLACK
PINK
RED
YELLOW
RED
N/A
BLK/RED
GREEN
BLUE
GREEN
BLK/WHT
BLK/WHT
ORANGE
BLK/WHT
VIOLET
VIOLET
BLK/WHT
RED/BLACK
BLK/WHT
ACC
TAN
WHITE/GREEN (+)
WHITE/GREEN (+)
WHITE/GREEN (+)
WHITE (+)
L GREEN (+)
WHITE/GREEN (+)
GREEN/BLACK
WHITE/GREEN (+)
D.GREEN/YEL
WHITE/GREEN
WHITE/GREEN
WHITE/GREEN
GREEN
LT-GREEN
GREEN
WHITE/GREEN (+)
GREEN
GREEN/YEL (+)
GREEN
LT. GREEN
LT. GREEN
ORANGE/YEL(+)
LT. GREEN
L GREEN (+)
LT. GREEN
LT-GREEN
GREEN/WHITE
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE
GREEN/RED (+)
GREEN
GREEN
GREEN/WHITE (+)
GREEN/ORANGE
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GRN/YELLOW (+)
GREEN/YELLOW
RED/BLACK
ORG/BLK
RED/BLACK
WHITE/TAN (+)
WHITE/TAN (+)
L BLUE
WHITE/GREEN
WHITE/TAN (+)
WHITE/TAN (+)
WHITE/TAN (+)
WHITE/TAN (+)
WHITE/TAN (+)
BLUE
RED
YELLOW
GREEN
RED/BLUE
TAN/YELLOW
GREEN/BLUE
GREEN/BLUE
GREEN/BLUE
RED/YEL
LT.GRN/RED
RED/YEL
Wht/Blk or Wht
YELLOW/BLUE
YELLOW/BLUE
YELLOW/BLUE
GREEN
TAN/YELLOW
WHITE
YELLOW/BLUE
DK GRN/YEL
WHITE/PINK
WHITE/RED
TAN/YELLOW
BLACK
BLACK
BLACK
BLACK/YELLOW
BLACK
YEL/WHITE
YEL/WHITE
BLACK
BLACK/YELLOW
BLACK
BLACK/WHITE
ORANGE
BLACK
BLACK
BLACK
YELLOW/GRN
YELLOW/GRN
YELLOW/WHT
n/a
YELLOW/WHITE
GRAY
GRAY
YEL/BLK
GRAY
BLACK/GRAY
GRAY
n/a
GRAY/WHITE
GRAY/WHITE
BRAKE LIGHTS TACH
WHITE (-)
N/A
N/A
N/A
D GREEN/PURPLE (-)
W/ UNLOCK
LT-GREEN/RED (-)
GREEN/RED
L. GREEN
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
DK. GREEN/PURPLE (-)
DK. GREEN/PURPLE (-)
GRAY/ORANGE (-)
DK. GREEN/PURPLE (-)
D GREEN/PURPLE (-)
N/A
DK. GREEN/PURPLE (-)
RED/BLACK (-)
GREEN (-)
GREEN (-)
GREEN (-)
W/ UNLLOCK
L GREEN (-)
BLUE/YELLOW (-)
DISARM WHEN START
GREEN (-)
RED/BLACK (-)
GREEN (-)
RED/GREEN (-)
RED/BLUE (-)
YELLOW/BLUE
BLUE/YELLOW(+)
RED/GREEN (-)
N/A
RED/GREEN (-)
N/A
N/A
N/A
VIOLET/YELLOW (-)
PURPLE/YELLOW
PURPLE/YELLOW
BLACK (-) in driver door
VIOLET/YELLOW (-)
VIOLET/YELLOW (-)
ALARM DISARM
LT. GREEN
RED/WHITE
RED
ORANGE (+)
BROWN/WHITE
BROWN (+)
ORANGE
GREEN (-)
ORANGE (+)
L.GREEN/BLK
RED/WHITE (+)
RED/WHITE (+)
RED/WHITE (+)
RED/BLACK (+)
RED/BLACK (+)
RED/BLACK (+)
RED/WHITE
BROWN (+)
RED/BLACK (+)
RED/BLACK (+)
ORANGE/BLACK (+)
BROWN
BLUE/BLACK (+)
WHITE/BLACK (+)
BROWN (+)
BROWN
BROWN
GREEN/BLACK (+)
GREEN (+)
GREEN (+)
GREEN`
GREEN/RED (+)
GREEN (+)
GREEN (+)
GREEN/ORANGE (+)
RED/YELLOW (-)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
BLACK/RED (-)
PINK/BLACK
BLACK/YELLOW
BLACK/YELLOW
BLUE/RED (+)
BLACK/YEL
D BLUE/RED (+)
D BLUE/RED (+)
BLACK/YELLOW (+)
D BLUE/RED (+)
DARK BLUE/RED (+)
N/A
GREEN/RED
N/A
GREEN/ORG (-)
GREEN/RED (-)
YEL/L GRN(-)
GREEN/RED
GREEN/ORANGE
GREEN/RED(-)
GREEN/RED (-)
N/A
GREEN/RED (-)
GREEN/ORG(-)
GREEN/BLK (-)
GREEN/RED (-)
GREEN/ORG (-)
GREEN/ORG (-)
YEL/LT GRN
GREEN/ORG (-)
GREEN/ORG (-)
D BLUE (-)
DK. BLUE (-)
DK. BLUE (-)
GREEN/RED (-)
GREEN/ORG(-)
WHITE/RED
GREEN/RED (-)
GRN/WHITE (-)
GREEN/RED (-)
GREEN/BLACK
GRN/BLACK (-)
GRN/BLACK (-)
GRN/BLACK (-)
GRN/WHITE (-)
GREEN (-)
GREEN (-)
GREEN/RED (-)
N/A
GREEN/ORG(-)
BLUE/RED (-)
RED/YELLOW
BLACK/RED(-)
BLK OR ORG/WHT
BLK/RED
BLACK/RED (-)
BLACK/RED
BLACK/RED
GRAY/ORG
GRAY/ORG
PARKING LIGHTS HORN
Directed Electronics Inc.
1999-01
1997-98
1992-96
1998-02
1993-97
1998-02
1996-00
1990-95
2001-02
1996-97
1998-00
1999-02
1995-01
1992-97
1992-01
RED/LT.BLU
RED/LT.BLU
GRAY/BLK
RED/BLACK
RED/LBLUE
RED/LTBLU
WHT/PINK
TAN
BLACK/WHT
BLK/WHITE
BLACK/WHT
BLK/WHITE
LGRN/PURP
BLACK/WHITE
BLACK/WHT
BLACK/WHT
BLUE
BLACK/WHT
BLK/WHT
BLK/WHT
BLUE
RED/BLACK
BLUE
BLACK/WHT
RED/L.GRN
BLUE
BLACK/WHT
BLUE
YELL/GREEN
BLK/L.GRN
BLK/L.GRN
BLACK/LGRN
GREEN/L.GRN
YELLOW
RED/BLACK
BLK/L.GRN
BLK/WHITE
BLK/WHITE
WHITE/GRN
WHITE/GRN
GREEN (+)
GREEN/WHITE
GREEN (+)
WHITE/GREEN (+)
ORANGE/BLUE
LT GREEN (+)
LT GREEN (+)
L GREEN (+)
L.GREEN
ORANGE/YEL(+)
RED/GREEN (+)
RED/GREEN (+)
DARK GREEN
DARK GREEN
YEL/BLACK (+)
YEL/BLACK (+)
WHITE/BLACK
N/A
WHITE
YELLOW/BLUE
BROWN/BLUE
WHITE/PINK
TAN/YELLOW
TAN/YELLOW
BLUE/GREEN
WHITE/BLACK
TAN/YELLOW
TAN/YELLOW
YEL/D.BLUE
YEL/D.BLUE
GREEN/WHITE
BLUE
LIGHT GREEN
UNLOCK WIRE
N/A
N/A
N/A
DARK GRN/PURPLE (-)
N/A
D GREEN/PURPLE (-)
GREEN/PURPLE
N/A
LT. GREEN/PURPLE (-)
N/A
N/A
N/A
RED/BLACK (-)
N/A
ORANGE/SILVER
GREEN/WHITE (+)
GREEN/WHITE (+)
WHITE/GREEN
RED/BLUE (+)
BROWN (+)
BROWN (+)
WHITE/BLACK (+)
BROWN (+)
RED/BLUE (+)
BROWN (+)
BROWN (+)
RED/BLACK (+)
RED/BLACK (+)
ORANGE/BLACK (-)
PINK
GREEN/BLACK
GREEN/SILVER
GREEN/RED (-)
GREEN/RED (-)
BLACK/BLUE (-)
DARK BLUE (-)
YEL/L.GREEN
BLACK (-)
YELLOW/GRN
BLACK/BLUE (-)
PURPLE/ORG (-)
YELLOW/L.BLUE
DRK GRN/ORG
DRK GRN/ORG
YELLOW (-)
BLK OR YEL
DK. BLUE (-)
YEL/LT.GREEN
GREEN/ORANGE
1998-02
1987-95
2000-02
1997-99
1997-02
1998-02
1992-97
GREEN
GREEN
BLACK/YEL
WHITE/RED
RED/L BLUE
BLACK/YELL
BLACK/YEL
BLACK/YEL
BLUE/YEL
BLACK/YEL
BLK/YEL
BLK/YEL
BLK/BLUE
WHITE/BLK
BLK/BLUE
BLACK/YEL
RED/L BLUE
BLK/BLUE
BLK/BLUE
N/A
N/A
2GRAY/YEL
2GRAY/YEL
2GRAY/YEL
N/A
N/A
2GRAY/YEL
2GRAY/YEL
N/A
N/A
N/A
N/A
BLUE
BLUE/WHITE
BLUE/WHITE
LT.GRN/WHITE
DK GRN/YEL
2000-02
1998-99
1993-96
1988-96
1994-00
2001-02
1998-00
1995-98
2000-02
1998-99
1996-97
1991-95
1994-95
1999-02
1990-98
1988-97
1991-94
1990-02
1993-95
BLACK/RED
N/A
GRAY/YEL
PINK/BLACK
GRAY/YEL
N/A
N/A
GRAY/YEL
GRAY/YEL
BLACK/RED
BLACK/RED
RED/GREEN
BROWN
N/A
N/A
N/A
YEL/Blk or Blu
1998-00 WHITE
BLACK/WHT
GREEN
RED/L.GRN
BROWN/PINK
LGRN/PURP
RED/GREEN
GREEN
RED/L.GRN
RED/L.GRN
DARK BLUE
DARK BLUE
BROWN
WHITE/RED
BLUE/BLK
BLUE/RED
BLUE/BLK
BLACK/YEL
GRAY/WHT
RED/L.BLUE
WHITE/PINK
RED/L BLUE
RED
GRAY/WHT
RED/L.BLUE
WHITE/PINK
BLK/D.BLUE
BLK/D.BLUE
RED
RED
1991-94
1999-02
1989-97
1989-02
1997-01
2002
1995-00
1989-02
1986-94
1989-98
1993-95
1995-02
1993-94
BLK/WHITE
BLK/WHITE
BLK/WHITE
4
1991-99 BLACK/YEL
1998-02 BLACK/RED
1992-97 BLACK/YEL
Make/model Year
Jeep
Kia
Cherokee
Cherokee
Cherokee
Grand Cherokee
Grand Cherokee
Grand Cherokee
Liberty
Wrangler
Wrangler
Wrangler
LEXUS
Sephia
Sportage
Sephia
Sportage
Sephia
ES 300
ES 300
ES 300
GS300
GS300
GS400
LS 400
LS 400
LS 430
LX450
LX470
RX 300
SC300
SC300
SC400
Lincoln
Mazda
Continental
Continental
LS
Mark VIII
Navigator
Towncar
Towncar
Mercedes Benz
626/
626/
626/
929/
B-Series
Millenia
Millenia
Millenia
MPV
MPV
MPV
MPV
MX3
MX5 / Miata
MX5 / Miata
MX6
Navajo
Protégé
RX7
ML320
Mercury
Capri
Cougar
Cougar
Grand Marquis
Mountaineer
Mountaineer
Mystique
Sable
Topaz
Tracer
Tracer Wagon
Villager
Villager
Mitsubishi
3000GT
Diamante
Diamante
NOTE
© 2005 Directed Electronics, Inc.
SEE SPECIAL NOTE FOR PARKING LIGHT
Equipped with Transponder
Equipped with Transponder
May have Transponder
1998 + Equipped with Transponder
Equipped with Transponder
1998 + May have Transponder
Equipped with Transponder
1998 Eqiuped with Transponder
Some are equipped with Transponder
1998 + May have Transponder
Has a second acc wire Black/lt-Green
Equipped with Transponder
Late model equipped with Transponder
Equipped with Transponder
Equipped with Transponder
Equipped with Transponder
Equipped with Transponder
Equipped with Transponder
Equipped with Transponder
Late model equipped with Transponder.
Equipped with Transponder
Equipped with Transponder
Equipped with Transponder
Blue Sheet update 2002.xls
IGN 1
BLUE/RED
BLUE/BLK
BLUE/BLK
BLUE/BLK
BLUE/BLK
BLUE/BLK
BLUE/BLK
BLUE/RED
BLUE/RED
BLUE/RED
BLUE/BLK
BLUE/RED
BLUE/RED
IGN 2
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
IGN 3/THEFT
WHITE/BLUE
WHITE/BLUE
WHITE/BLUE
BLUE
N/A
WHITE/BLUE
WHITE/BLUE
WHITE/BLUE
WHITE/BLUE
WHITE/BLUE
WHITE/BLUE
WHITE/BLUE
WHITE/BLUE
WHITE/BLUE
WHITE/BLUE
BLACK/BLUE
BLACK/BLUE
WHITE/GRN
WHITE/GRN
WHITE/BLUE
WHITE/BLUE
WHITE/BLUE
WHITE/BLUE
BLUE/BLACK
BLUE
BLUE
BLUE
BLUE/BLACK
BLUE/WHITE
BLUE/WHITE
BLUE/BLK
BLUE/YEL
BLUE/YEL
BLUE
BLUE
BLUE
ACC
RED/GREEN (+)
L GRN/RED(+)
RED/GREEN (+)
RED/BLACK
RED/GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
GREEN/YEL(+)
GREEN/YEL(+)
RED/GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
GREEN/YEL(+)
GREEN/YEL(+)
GREEN/YEL(+)
YEL/BLACK (+)
YEL/BLACK (+)
RED/GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
GREEN/YEL(+)
GREEN/ORNG
GREEN/WHITE
GREEN/WHITE
GREEN (+)
GREEN/SYLVER
GREEN (+)
GREEN (+)
BLUE/ORANGE
GREEN
GREEN
GREEN
GREEN
GREEN
WHITE
VIOLET/WHT
PURPLE/WHITE
WHITE
WHITE
WHITE
WHITE
PINK/BLUE
PINK/BLUE
WHITE/GREEN
WHITE/GREEN
WHITE/GREEN
WHITE/GREEN
WHITE/GREEN
WHITE
WHITE
WHITE or BLUE
GREEN/WHITE
BLUE
BLUE/ORANGE
BLUE
BLUE/BLACK
PINK/BLUE
BRAKE LIGHTS TACH
N/A
N/A
L.GREEN
N/A
N/A
N/A
N/A
GREEN/YELLOW (-)
GREEN/YELLOW (-)
GREEN/YELLOW (-)
W/ UNLOCK
N/A
N/A
N/A
RED/BLACK (-)
N/A
WHITE/BLUE
GREEN/YELLOW (-)
N/A
L GREEN (-)
ORANGE (-)
GREEN/WHITE
GREEN/WHITE
N/A
BROWN/WHITE
N/A
N/A
BROWN
N/A
N/A
ALARM DISARM
BROWN (+)
BROWN (+)
BROWN/WHITE
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
RED/BLUE (+)
GRN/BLK
RED/BLUE (+)
GREEN/RED (+)
RED/BLUE (+)
RED/BLUE (+)
RED/BLUE (+)
BLUE/RED (+)
BLUE/RED (+)
RED/GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
RED/GREEN (+)
RED/BLUE (+)
PINK/BLUE (+)
PINK/BLUE (+)
PINK/BLUE (+)
ORANGE/BLACK (-)
PINK
WHITE/RED
RED/BLUE (+)
RED/BLUE (+)
BLUE/RED (+)
PINK/BLACK (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (-)
GREEN/WHITE (+)
GREEN/WHITE (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
GRAY/YEL (-)
N/A
GRN/WHITE (-)
GRN/WHITE (-)
N/A
GRN/WHITE (-)
GREEN/WHITE
LGRN/BLACK (-)
GRN/BLACK (-)
GRN/WHITE (-)
GRN/WHITE (-)
GRN/WHITE (-)
GRN/WHITE (-)
GREEN/WHT
GRN/BLACK (-)
GRN/BLACK (-)
GRN/BLACK (-)
YELLOW (-)
BLK OR YEL
WHITE/GRN
GRAY/YEL (-)
GRN/WHITE (-)
LGRN/BLACK (-)
VIOLET (-)
GREEN/RED (-)
GREEN/RED (-)
GREEN/BLACK
GREEN/WHITE
LIGHT GREEN(-)
WHITE/BLUE
LT.GREEN/BLK
GRN/BLACK (-)
GREEN/BLK (-)
GREEN/BLK (-)
PARKING LIGHTS HORN
Directed Electronics Inc.
START
GREEN
BLK/WHITE
BLK/WHITE
BLK/WHITE
WHITE/BLK
BLK/WHITE
BLK/WHITE
BLUE/BLK
BLK/WHITE
BLK/WHITE
BLK/WHITE
BLK/WHITE
BLK/WHITE
N/A
N/A
N/A
N/A
N/A
1999 have Transponder
2001 have Transponder
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
WHITE (+)
WHITE (+)
WHITE
WHITE (+)
WHITE (+)
WHITE (+)
WHITE (+)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK/YELLOW (+)
BLACK/YELLOW (+)
RED/BLACK (+)
BLACK/YELLOW (+)
BLACK/YELLOW (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
BLACK/YELLOW (+)
BLACK/YELLOW (+)
BLACK/YELLOW (+)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK/RED (-)
BLACK/RED (-)
GREEN/BLK (-)
BLACK (-)
BLACK/RED
GREEN/BLK (-)
GREEN/BLK (-)
GREEN/BLK (-)
BLACK/RED (-)
N/A
BLACK/RED (-)
N/A
BLACK/GRAY
BLACK/GRAY
N/A
N/A
VIOLET/Light BLUE
WHITE/RED (-)
N/A
N/A
N/A
BROWN/WHITE
N/A
LT. GREEN/BLACK (-)
N/A
BRW/WHIT
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
WHITE
BLUE/TAN
BLACK/GRAY
WHITE
WHITE
WHITE
GRAY/L BLUE
GRAY/L BLUE
BLACK/GRAY
L-Green
L-Green
N/A
N/A
N/A
ORANGE/BLACK (-)
N/A
GREEN/BLACK (-)
N/A
N/A
DISARM WHEN START
N/A
GREEN/BLACK (-)
N/A
BLUE/ORANGE
RED/WHT
YELLOW/RED
YELLOW/RED
LT. GRN/ORG
BLUE/BLACK
WHITE/TAN (+)
WHITE/TAN (+)
WHITE/BLK
WHITE/TAN (+)
WHITE/TAN (+)
GREEN
GREEN
GREEN
WHITE/TAN (+)
WHITE/TAN (+)
WHITE/TAN (+)
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHT OR PPL
GREEN/YELLOW (-)
N/A
GREEN/YELLOW (-)
GRAY/RED (-)
GREEN/YELLOW (-)
GREEN/YELLOW (-)
PINK/BLUE
L GREEN (-)
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
BLK/YELLOW
WHITE
BLACK/RED
BLACK/RED
BLACK/RED
BLACK/YEL
BLACK/YEL
BLACK/RED
BLACK/YEL
BLK/YEL
BLUE/BLK
BLUE/BLK
BLK/YEL
BLK/YEL
BKL/PINK
N/A
N/A
N/A
BLACK/PINK
BLACK/PINK
RED
RED/YEL
RED/YEL
RED
BLACK/YEL
RED/YEL
BLACK/YEL
RED/YELLOW
RED/YEL
N/A
N/A
RED/GREEN
BROWN
WHITE
BLACK/PINK
N/A
RED/YEL
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
BROWN
BROWN
BROWN (+)
LT. BLUE (+)
LT. BLUE (+)
LT. BLUE (+)
LT. BLUE (+)
LT. BLUE (+)
LT. BLUE (+)
BROWN (+)
BLK/ORG
BLK/WHT
BLUE
BLUE
BLUE
BLACK/WHT
BLACK/ORG
BLACK/WHT
ORANGE
L BLUE (+) *
L BLUE (+)
L BLUE (+)
WHITE (+)
WHITE (+)
WHITE
WHITE (+)
WHITE
WHITE
WHITE
WHITE
WHITE (+)
WHITE (+)
N/A - Transponder
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
PK3
BROWN
BROWN
BROWN
ORANGE
ORANGE
ORANGE
ORANGE
BROWN
BROWN
ORANGE
ORANGE
ORANGE
BROWN or Orange
5
N/A
N/A
N/A
N/A
NA
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
GREEN/BLK (-)
Blk/Yel or Blu/Blk
BLACK/RED
BLK/WHT
BLACK/RED
BLACK/RED
BLACK/RED
BLACK/RED
BLACK/RED
BLK/WHITE
BLK/WHITE
BLK/RED
BLACK/RED
BLACK/RED
BLACK/RED
BLACK/RED
BLK/WHITE
BLK/WHITE
BLK/WHITE
BROWN
WHITE/RED
BLACK/RED
BLACK/RED
BLACK/RED
BLK/WHITE
N/A
N/A
N/A
WHITE
N/A
N/A
N/A
N/A
LT. GREEN (-)
N/A
LT. GREEN (-)
LT. GREEN (-)
LT. GREEN (-)
LT. GREEN (-)
N/A
2000-02
1991-99
1996-98
1992-96
1999-02
1987-98
1996-01
2001-02
1999-00
1995-96
1990-94
1998
1997-02
BLK/WHITE
BLK/YEL
BLACK/YEL
BLK/WHITE
BLK/YEL
BLK/WHITE
BLACK/YEL
BLACK/YEL
BLK/YEL
BLK/BLUE
BLK/WHITE
BLK/WHITE
BLK/WHITE
BLK/WHITE
BLACK/YEL
BLACK/YEL
BLACK/YEL
BLK/GRN*
RED/GRN*
BLACK/YEL
BLK/WHITE
BLK/WHITE
BLACK/YEL
WHITE
DK-GREEN
WHITE
PURP/WHT
WHITE
ORANGE
ORANGE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
WHITE
1995-98
1989-90
1989-98
1987-96
1998-01
1993-97
2002
1998-02
1998-00
1999-01
1997-98
1995-96
1987-94
2002
1996-02
1990-95
1987-97
1996-02
1993-95
2000-02
2000-02
2000-03
2000-04
PINK
PINK
PINK
PINK
PINK
PINK
PINK
WHITE (+)
L BLUE (+)
WHITE (+)
L BLUE (+)
L BLUE (+)
WHITE (+)
WHITE (+)
WHITE (+)
YELLOW
YELLOW
PURPLE
YELLOW
YELLOW
YELLOW
YELLOW
ORANGE
BROWN
ORANGE
BROWN
BROWN
BROWN
BROWN
WHT or ORNG
ORNG or BRWN
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
N/A
LT. BLUE
N/A
LT. BLUE
LT. BLUE
N/A
N/A
N/A
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
BLACK/ORG
BLACK/ORG
N/A
GRN/RED
BLK/ORG
BLUE/BLK
BLUE/BLK
BLUE/BLK
BLACK/ORG
RED/WHITE
BLACK/ORG
PURPLE
ORANGE
D.GREEN
ORANGE
ORANGE
ORANGE
ORANGE
1993-98
1999-01
2001-02
1995-99
1995-02
1991-94
1987-96
1990-95
1997-99
1992-98
1998-02
1996-98
1994-96
1997-98
1990-91
1990-02
DARK BLUE
DARK BLUE
PINK/WHT
BLUE
BLUE
BLACK/WHT
BLACK/WHT
BLACK/WHT
DARK BLUE
DARK BLUE
DARK BLUE
WHT or ORNG
BLACK/WHT
BLACK/WHT
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
BLACK/YEL
BLACK/YEL
BLACK/YEL
YELLOW
YELLOW
YELLOW
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
PINK
N/A
N/A
1989-95
1996-02
2001-02
1996-00
1991-95
1987-94
1993-94
1991-94
1995-02
1997-00
1993-94
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
WHITE
ORANGE
ORANGE
ORANGE
DK-GREEN
WHITE
PURPLE
WHITE
ORANGE
ORANGE
N/A
WHITE
WHITE
2000-02
1992-99
1998-02
1987-97
1999-02
1997-02
1988-96
1998-02
1993-94
1987-89
2000-02
1995-99
1997-98
1990-96
Make/model Year
Nissan
Eclipe
Eclipse
Eclipse Spider
Expo
Galant
Galant
Mirage
Montero
Montero
Montero
Montero
Montero
Montero Sport
OLDSMOBILE
200 SX
200SX
240 SX
300 ZX
Altima
Altima
Altima
Frontier
Frontier/Pickup
Maxima
Maxima
Maxima
Maxima
Maxima
Pathfinder
Pathfinder
Pick-up
Quest
Quest
Sentra
Sentra
Sentra
Xterra
PLMOUTH
Acheiva
Alero
Arora
Arora
Bravada
Bravada
Cierra
Cruiser
Cutlass
Eighty-Eight
Intrigue
LSS
Ninety Eight
Regency
Regency
Silhouette
PONTIAC
Acclaim
Breeze
Voyager
Voyager
Voyager
Colt
Colt Vista
Laser
Neon
Prowler
Sundance
Bonneville
Bonneville
Firebird
Firebird
Grand Am
Grand Prix
Grand Prix
Montana
Sunbird
Sunbird
Sunfire
Sunfire
Transport
Transport
SATURN
NOTE
Equipped with Transponder
Equipped with Transponder
1999 have Transponder
2001 have Transponder
Equipped with Transponder
Equipped with Transponder
1999 + Equipped with Transponder
2 Start wires - 2nd wire is red
2 Start wires - 2nd wire is red
2002 Equipped with Transponder
Equipped with passlock II
Equipped with passlock II
Equipped with VATS System.
Equipped whith Passlock II
1992-1996 has no Ignition 3
Equipped whith Passlock II
1998+ Equipped with Passkey III
© 2005 Directed Electronics, Inc.
( note: this vehicle needs 180 ohm resistor
Late model equipped with Transponder
Equipped w/ VATS. *In 1992-95 Brake wire is White
Equipped w/ VATS
Equipped with passlock II
Equipped with Passkey III
Equipped with Transponder
Equipped with passlock II
Equipped with Passlock
Blue Sheet update 2002.xls
IGN 1
ORANGE
ORANGE
ORANGE
ORANGE
ORANGE
IGN 2
N/A
N/A
N/A
N/A
N/A
IGN 3/THEFT
BROWN
BROWN
BROWN
BROWN
BROWN
ACC
WHITE/BLACK
WHITE/BLACK
WHITE/BLACK
WHT/BLK
GREEN/BLACK (+)
WHITE/BLACK
WHITE/BLACK (+)
BLK/BLUE
GREEN/BLACK (+)
WHITE/GREEN (+)
L BLUE (+)
L BLUE (+)
L BLUE (+)
L BLUE (+)
L BLUE (+)
YELLOW/BLUE
BLUE
BLACK/BLUE
YEL/GRN
YELLOW
YELLOW
BLUE
BLUE
BLUE
WHITE
WHITE
WHITE
WHITE
WHITE
BRAKE LIGHTS TACH
N/A
remote
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
ALARM DISARM
GREEN
RED/YELLOW (+)
RED/YELLOW (+)
RED/YELLOW (+)
RED/YELLOW (+)
RED/YELLOW
PURPLE
ORANGE (+)
BLACK/YELLOW (+)
PURPLE
RED/YELLOW
ORANGE
RED (+)
ORANGE (+)
RED/BLACK
RED
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BROWN (+)
BLU/BLK
N/A
BLUE/GREEN
BLUE/GREEN
BLKor BLUE/BLK
BLUE/GREEN
N/A
N/A
GREEN/WHITE
RED/GREEN (-)
RED/GREEN (-)
RED/GREEN (-)
GREEN/BLACK
GREEN/BLACK
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
BLACK (-)
PARKING LIGHTS HORN
Directed Electronics Inc.
START
PINK
PINK
PINK
PINK
PINK
GREEN
BLACK/BLUE
RED/YEL
BLK/BLU
BLUE
BLACK/BLUE
N/A
YELLOW
BLUE
RED/YEL
remote
N/A
N/A
N/A
N/A
N/A
BROWN/YEL
GREEN/RED (-)
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
BROWN
YELLOW/GRN
BROWN
BRN/WHITE
BROWN
BROWN
1993-01
1996-01
1992-95
1996-99
1993-95
GRN/ORG
N/A
N/A
N/A
N/A
N/A
RED/YEL
N/A
N/A
RED/YEL
BLUE/YEL
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE
GREEN/WHITE
WHITE/BLUE (-)
WHITE/BLUE (-)
N/A
BLU or BLU/WHT (-)
unlock
N/A
YELLOW
BLUE
RED
BLK
BLK/WHITE
BLACK
RED
GREEN
BLACK
RED
BLK/BLU
YELLOW/BLK
BLUE
BLUE
BLUE/RED
BLUE
WHITE/BLK
BLACK/WHT
BLUE/RED
BLK/YEL
BLK/YEL
BLK/YEL
BLUE/RED
WHITE/BLK
BLK/WHITE
BLK/WHITE
N/A
N/A
N/A
N/A
N/A
N/A
1998-02
1998-01
1993-98
2002
1987-94
1999-00
1990-98
2000-02
1990-94
1992-97
YEL/BLACK
N/A
N/A
YEL/BLACK
RED/GREEN
YEL/BLACK
GREEN/RED (-)
GREEN/RED (-)
GRN/BLACK (-)
N/A
GRN/BLACK (-)
GRN/BLACK (-)
GRN/BLACK (-)
GRN/BLACK (-)
BLU/BLK
BLK/BLUE
BLACK/WHT
BLK/BLUE
BLK/BLUE
BLUE/BLACK
BLK/BLUE
RED/GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN/BLACK (+)
GREEN (+)
GREEN (+)
LT. GREEN (-)
Blk/Red or Blk/GRN
WHT/GRN
BLACK/YEL
BLACK/RED
BLACK/RED
RED/YEL
BLK/YEL
N/A
N/A
unlcok
BLUE/SILVER
BLUE (-)
RED/GREEN (-)
N/A
unlock
unlock
GREEN (-)
GREEN/RED (-)
GREEN/RED (-)
WHITE/RED (-)
GREEN/ORG (-)
GREEN/RED (-)
N/A
GRN/BLACK (-)
GRN/BLACK (-)
WHITE/RED
GREEN/YEL(-)
GREEN/YEL(-)
GREEN/RED (-)
GREEN/RED (-)
GREEN/RED (-)
GREEN/RED (-)
GREEN/BLK (-)
GRN/BLACK (-)
BLUE/RED (-)
GREEN/BLK (-)
GREEN/RED (-)
GREEN/RED (-)
GREEN/YEL(-)
GREEN/YEL(-)
GREEN/RED (-)
1998-02
1999-02
1986-95
1996-98
1999-00
1989-98
BLACK
BLACK
BLK/YELLOW
GREEN
BLACK
BLACK/ORG
BLACK
N/A
unlock
BLUE/RED (-)
BLUE/YELLOW
N/A
N/A
BLUE/YELLOW (-)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN(+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GRN/WHITE(+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (+)
GREEN (-)
GREEN (+)
RED/GREEN (+)
BLACK/RED
BLACK/RED
WHT/RED
BLACK/YEL
BLACK/ORG
BLACK/RED
BLACK/ORG
BLK/RED
BLACK/ORG
BLUE/RED
BLUE/RED
BLACK/ORG
BLK/WHT
BLACK/ORG
BLACK/RED
BLUE/BLK
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
BLUE (-)
BLUE (-)
BLUE (-)
GREEN (-)
BLUE (-)
N/A
BLUE (-)
RED/WHITE (-)
WHITE/BLUE (-)
N/A
1999-02
1990-98
2000-02
1998-00
1995-97
1997-01
1987-96
2002
2000-02
1996-00
1990-95
1986-89
1998-02
1987-97
2000-01
1999-02
1991-97
1998
BRWN/WHT
BRN OR GRY
BROWN
GRAY
YEL/GRN
BLACK
GREEN/RED
BLACK
BLACK
BLACK/WHITE
BLACK
BLACK/WHITE
WHITE
BLACK/BLUE
BLACK
BLACK
BLACK
BLACK
BLACK
ORANGE
ORANGE
BLACK
ORANGE
BLACK
BLACK
BLACK/BLUE
BLACK/BLUE
BLACK
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
GREEN/WHITE (+)
GREEN/WHITE (+)
RED/GRN
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE
GREEN/WHITE
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHT
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
GREEN/WHITE (+)
RED/WHITE (+)
GREEN/WHITE (+)
BLACK/YEL
BLACK/YEL
BLK/ORG
BLACK
BLACK/YEL
BLACK/YEL
BLACK/YEL
BLACK/YEL
BLUE/RED
GRAY
GRAY
BLUE/RED
BLACK/YEL
BLACK/YEL
BLACK/YEL
BLK/RED
BLACK/YEL
BLK/RED
BLACK/YEL
BLK/ORG
RED/WHITE
BLUE/RED
BLK/YEL
BLACK/YEL
BLACK/YEL
BLK/YEL**
BLACK *
BLACK/YEL
BLACK/YEL
BLACK/YEL
BLACK/YEL
BLK/YEL**
BLACK/YEL
BLACK/WHT
BLACK/YEL
BLACK/YEL
BLUE/RED
BLUE/RED
WHT/GRN
BLUE
PINK/BLUE
BLUE/RED
PINK/BLUE
BLU/RED
GRAY
GRAY
GRAY
GRAY
BLUE/RED
BLUE/RED
WHITE/BLUE
BLACK
BLUE/RED
BLACK
BLUE/RED
BLUE/RED
PINK/BLUE
BLACK/YEL
BLU/RED
BLUE/RED
BLUE/RED
BLUE/RED
BLUE/RED
BLUE
BLUE
PINK/BLUE
BLUE/RED
BLUE/RED
BLUE/RED*
BLACK/YEL
BLACK/YEL
BLUE/RED
BLK/BLUE
BLACK/ORG
BLK/YEL
BLK/YEL
BLACK/RED
BLK/RED
BLACK/RED
BLACK/RED
BLACK
BLACK/RED
BLACK/RED
BLACK/RED
BLACK/ORG
BLACK/RED
BLACK/RED
BLACK/RED
BLUE/RED
BLK/WHITE
BLACK/RED
BLUE/YELLOW
N/A
BRN/BLUE (-)
BRN/BLUE (-)
BLACK/YEL (-)
BROWN/BLUE(-)
BLACK/YEL (-)
BROWN/BLK (-)
BROWN/BLUE (-)
GREEN/BLK
BLACK
BLK/WHITE
RED
RED
RED
BLK/WHITE
BLK/WHITE
BLK/WHITE
BLACK
BLK/WHITE
BLK/WHITE
RED
BLK/WHITE
BLACK
BLK/WHT
BLK/WHT
BLK/WHT
BLK/WHITE
RED
RED
BLACK
BLK/WHITE
BLACK
BLK/WHT
RED
BLK/WHT
RED
RED
BLK/WHITE
BLACK/ORG
BLK/YEL*
BLACK
BLACK
BLACK
GREEN/BLK
GRAY/VIOLET
GRAY/BLACK
GRAY/GREEN (+)
GRAY/GREEN (+)
GRAY/TAN GRAY/YEL
GRAY/BLK GRAY/RED
GRAY/TAN GRAY/YEL
GRAY/BLACK
GRAY/BLACK
GREEN/RED (+)
GRAY/BLK
1994-95
2000-02
1996-98
1995
1989-95
1991-97
2001-02
1996-01
1998-02
1998-02
1994-98
1996-99
1994-95
1995-02
1998-99
1987-97
2000-02
WHITE/BLUE (-)
UNLOCK WIRES (-)
N/A
N/A
UNLOCK WIRES (-)
N/A
UNLOCK WIRES (-)
N/A
N/A
UNLOCK WIRES (-)
UNLOCK WIRES (-)
N/A - Transponder
GREEN/ORNG
BLACK/RED
GREEN/BLACK
GREEN/BLACK
GREEN/YEL
BLACK/RED
GREEN/YEL
GREEN
GREEN/RED
GREEN/BLUE
GREEN/BLUE
BROWN/RED
N/A
N/A
BLACK/YEL
BROWN/RED
N/A
BROWN/RED
N/A
N/A
N/A
BLK/YEL
RED/BLACK (+)
BLACK/RED (+)
BLACK/RED (+)
BLACK/RED (+)
RED/BLACK (+)
RED/BLACK (+)
RED/BLACK (+)
RED/BLK
BLACK/RED (+)
RED/BLUE (+)
RED/BLK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK/RED
BLACK/YEL
BLACK/YEL
BROWN/RED
BLACK/RED
BLACK/YEL
BLACK/RED
YELLOW
BLK/YELLOW
WHITE/YEL
YEL/BLU
RED/BLACK
RED/BLACK
BLACK/YEL
RED/BLACK
RED/BLUE
RED/BLACK
RED/BLUE
RED/BLK
BLACK/YEL
RED/BLACK
RED/BLACK
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
1998-02
1995-02
1994-95
1990-93
1999-02
1994-98
1999-02
1998-00
1993-97
1998-00
2001-02
Make/model Year
SUBARU
SC1/SC2
SL / SL1 / SL2
SL / SL1 / SL2
SW1 / SW2
SW1 / SW2
SUZUKI
Forrester
Impreza
Impreza
Impreza
Justy
Legacy / Outback
Legacy
Legacy
Loyale
SVX
TOYOTA
Esteem
Grand Vitara
Samurai
Sidekick
Swift
Swift
VOLKSWAGEN
4 Runner
4 Runner
Avalon
Avalon
Avalon
Camry
Camry
Camry
Celica
Celica
Celica
Celica
Corolla
Corolla
Echo
Land Cruiser
Land Cruiser
Land Cruiser
Most models
MR2
MR2 Spyder
Paseo
Paseo
Pick-up
Previa
RAV 4
RAV 4
Sienna
Sienna
Supra
T100 Pick-up
T100 Pick-up
Tacoma
Tercel
Tercel
Tundra
Beetle
Cabriolet
Corrado
Corrado
Golf & GTI
Golf &GTI
JETTA
Eurovan
Eurovan
PASSAT
PASSAT
6
NOTE
© 2005 Directed Electronics, Inc.
Late model equipped with Passkey III
Late model equipped with Passkey III
Factory alarm disarm with fac transmitter
Equipped with Transponder
May Be Equipped with Transponder
NEED RELAY FOR STARTER INTERUPT
Equipped with Transponder
* 1998-2001 IGN 2 is BLACK / YELLOW
*94 wire is BLACK - **93 wire is BRN/WHT
*95 wire is RED/BLUE
equipped with transponder key
SPLIT PARKING LIGHT, USE DIODE
SPLIT PARKING LIGHT, USE DIODE
SPLIT PARKING LIGHT, USE DIODE
Equipped with Transponder
Equipped with Transponder
Blue Sheet update 2002.xls
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement