Sharp ER-01PU User manual

Sharp ER-01PU User manual
POS TERMINAL
MODEL
ER-A770
(For "U"&"A" version)
CONTENTS
CHAPTER 1. SRV RESET (Program Loop Reset) and switch to SRV mode...... 2
CHAPTER 2. MASTER RESET (All Memory Clear) ........................................ 3
CHAPTER 3. READING OF SRV MODE PROGRAM ..................................... 6
CHAPTER 4. SRV MODE PROGRAMMING ("2 SETTING")......................... 12
CHAPTER 5. IRC SETTING ("3 IRC SETTING") ........................................... 39
CHAPTER 6. SRV MODE PROGRAMMING ("4 DOWN LOAD") .................. 42
CHAPTER 7. SRV MODE PROGRAMMING ("5 DIAGNOSTICS")................ 42
For setting in PGM1 or PGM2 mode, refer to the Operation Manual.
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
>>>>> USE FONT <<<<<
Helvetica/ Helvetica-Condensed/ Century-Schoolbook/ Symbol & OriginalFonts: (RingWorld2/RingFont2/Pa Symbol/PartsCod)
-----------------------------------------------------------------------------------> Wpsym
Major keys used in the SRV mode
The following major keys are used in the SRV mode.
FUNCTION
KEY
DESRIPTION
CURSOR UP
Moves cursor up (1 character)
CURSOR DOWN
Moves cursor down (1 character)
CURSOR RIGHT
Moves cursor right (1 character) & Open sub menu (PGM only)
CURSOR LEFT
Moves cursor left (1 character) & Open sub menu (PGM only)
PAGE UP
PAGE DOWN
CLEAR
CANCEL
ENTER
PAGE UP
Moves page up (1 page)
PAGE DOWN
Moves page up (1 page)
CL
CANCEL
Clear numeric entry or error message
Operation cancel & back to previouse menu.
ENTER
Data entry
BACK SPACE
BS
Back space
MODE MENU
MODE
Back to mode selection menu
ALL ENTER
CA / AT
All entry completion.
TOGGLE SELECT
INSERT/OVER WRITE
"." (DECIMAL POINT)
INS
RECALL
RECALL
DELETE
DEL
Toggles between selections
Change character entry mode.
Re-call item programming
Delete item
CHAPTER1. SRV RESET (Program Loop Reset) and switch to SRV mode
In the ER-A770, the following reset switch (location No.: SW1) is used
to switch to the service (SRV) mode and to reset.
SRV. reset
Used to return the machine back to its operation state after a lock up
has occurred.
PROCEDURE
1) Turn off the AC switch.
2) Set the reset switch to "ON" position
3) Turn on the AC switch. (Wait one second)
4) Turn to "OFF" the reset switch.
5) The SRV mode is displayed as shown below.
DISPLAY:
Reset
switch
ON
RESET SW
SW1
Used to reset and resume initial program without clearing memory.
OFF
Rear side :"ON" position(Reset state)
ON
RESET SW
OFF
Front side :"OFF" position(Run state)
CHAPTER 2. MASTER RESET (All Memory Clear)
There are three possible methods to perform a master reset.
6) The master reset is started.
DISPLAY:
MASTER RESET
MRS-1 (Master resetting 1)
Used to clear all memory contents and return machine back to its
initial settings.
MASTER RESET
The keyboard is set to the keyboard default keyboard layout.
7) After completion of the master reset, the buzzer sounds three
times and the following SRV mode display is shown.
DISPLAY:
PROCEDURE
1) Turn off the AC switch.
2) Set the reset switch to "ON" position
3) Turn on the AC switch. (Wait one second)
4) While holding down the MRS-1 key, place the reset switch to
"OFF".
MRS-1 key: The key located on Left upper corner of the keyboard.
MRS-1 Key
MRS-2 (Master resetting 2)
Used to clear all memory and keyboard contents. This reset returns
all programming back to defaults.
The keyboard must be entered from. This reset is used if an application needs different keyboard layout other than that supplied by a
normal MRS-1.
PROCEDURE
1) Turn off the AC switch.
Keyboard layout
2) Set the reset switch to the "ON" position
5) Enter the password key operation
3) Turn on the AC switch. (Wait five seconds)
DISPLAY:
4) While holding down the MRS-2 key, place the reset switch to
"OFF" .
ENTER PASSWOPRD
Press the four corners of the keyboard in
the sequence of a, b, c, and d.
c
a
b
d
Keyboard layout
MRS-2 key: The key located at the upper right corner of the
keyboard.
MRS-2 Key
Keyboard layout
7) The master reset is started.
5) Enter the password key operation
DISPLAY:
DISPLAY:
ENTER PASSWOPRD
MASTER RESET
Press the four corners of the keyboard in
the sequence of a, b, c, and d.
c
a
8) After completion of the master reset, the buzzer sounds three
times and the following SRV mode display is shown.
DISPLAY:
b
d
Keyboard layout
6) Set the function keys in the table below. (Start from the zero "0"
key, The keys are displayed sequentially.)
DISPLAY:
MRS-3 (Master resetting 3)
ENTER 0
KEY
Master resetting 3 requires the entry of Serial No. data in addition to
master resetting 1.
[Key setup procedure]
MRS-2
executed
0
Key
position set
Free key
Setup
complete
After completion of the MRS-3, the following operations and programming will be inhibited.
1. GT programming.
0
Disable
2. All memory download via RS-232.
3. GT resets with Z report. ( Z report can be made, but GT will not be
reset.)
NOTES:
1: When the 0 key is pressed, the key of the key number on
display is disabled.
2: Push the key on the position to be assigned. With this, the
key of the key number on display is assigned to that key
position.
3: When relocating the keyboard, the PGM 1/2 mode uses
standard key layout.
Key
No.
Key
name
Key
No.
Key name
Key
No.
Key name
001
"0" key
011
"00" key
022
"CANCEL" key
002
"1" key
013
Decimal point "·" key
023
"ENTER" key
003
"2" key
014
"CL" key
024
"CA/AT" key
004
"3" key
015
"@/FOR" key
005
"4" key
016
"SBTL" key
006
"5" key
017
"MODE" key
007
"6" key
018
UP "
008
"7" key
019
DOWN "
009
"8" key
020
LEFT "
010
"9" key
021
RIGHT "
" key
" key
" key
" key
PROCEDURE
1) Turn off the AC switch.
2) Set the reset switch to the "ON" position.
3) Turn on the AC switch. (Wait one second)
4) While holding down the MRS-3 key, place the reset switch to
"OFF" .
MRS-3 key: The key located at the lower left corner of the
keyboard.
7) Set the function keys in the table below. (Start from the zero "0"
key, The keys are displayed sequentially.)
DISPLAY:
ENTER 0
KEY
[Key setup procedure]
MRS-3
executed
Key
position set
0
Free key
Setup
complete
0
Disable
NOTES:
1: When the 0 key is pressed, the key of the key number on
display is disabled.
MRS-3 Key
2: Push the key on the position to be assigned. With this, the
key of the key number on display is assigned to that key
position.
keyboard layout
5) Enter the password key operation
3: When relocating the keyboard, the PGM 1/2 mode uses
standard key layout.
DISPLAY:
ENTER PASSWOPRD
Press the four corners of the keyboard in
the sequence of a, b, c, and d.
c
a
Key
No.
Key name
"00" key
022
"CANCEL" key
Decimal point "·" key
023
"ENTER" key
024
"CA/AT" key
Key
No.
Key
name
Key
No.
001
"0" key
011
002
"1" key
013
003
"2" key
014
"CL" key
004
"3" key
015
"@/FOR" key
005
"4" key
016
"SBTL" key
006
"5" key
017
"MODE" key
007
"6" key
018
UP "
008
"7" key
019
DOWN "
Key name
009
"8" key
020
LEFT "
010
"9" key
021
RIGHT "
" key
" key
" key
" key
8) The master reset is started.
DISPLAY:
b
MASTER RESET
d
Keyboard layout
6) The product serial No. input window is displayed as shown below.
9) After completion of the master reset, the buzzer sounds three
times and the following SRV mode display is shown.
DISPLAY:
DISPLAY:
SERIAL No.
00000000
Enter the product serial No. of this POS and enter the [CA/AT] key.
CHAPTER 3. READING OF SRV MODE PROGRAM
The setting contents of the SRV mode can be reported with the
display or printer.
Sample of program reports
DISPLAY: SRV mode screen
1. [1 SYSTEM PRESET]
DISPLAY:
Select "1 READING" and press the ENTER key.
DISPLAY: READING item selection screen
Select the desired item, press the ENTER key.
DISPLAY: OUTPUT read destination select screen
Select the output desired item, press the ENTER key.
The setting content is displayed and printed.
PRINTER:
2. [2 DEVICE ASSIGN]
DISPLAY:
PRINTER:
Report title
Device name / Terminal No. /
Channel No.
Printer name /
Auto cutter function
Device name / Not assigned
Paper sheet type
3. [3 FREE KEY LAYOUT]
PRINTER:
DISPLAY:
Report title
Key No. / Key text /
Key position code
Key No. / Key text /
Not assigned
4. [4 FILE]
PRINTER:
DISPLAY:
Report title
File table No. / No. of records/
No. of used records
File table No. / No. of records /
No. of blocks / No. of used
records
File table No. /
No. of index records / No. of data
records /
No. of used records
DISPLAY: OUTPUT read destination select screen
The setting content is displayed and printed
DISPLAY:
File memory start address
Empty memory start address
Memory end address
5. [5 SSP]
DISPLAY: SSP item selection screen
Select the desired item, press the ENTER key.
PRINTER:
CHAPTER 4. SRV MODE PROGRAMMING (“2 SETTING”)
DISPLAY: SRV mode screen
1. [1 DEVICE ASSIGN]
DISPLAY: Setting item select screen
Select “2 SETTING” and press the ENTER key.
Select “1 DEVICE ASSIGN” and press the ENTER key.
DISPLAY: SETTING item selection screen
DISPLAY: DEVICE ASSIGN select screen
Select the desired item, press the ENTER key.
The item setting input screen is displayed.
Select the item to be changed and press the ENTER key.
[1 DEVICE ASSIGN] - [1 J PRINTER]
DISPLAY : Setting screen
DISPLAY
TERMINAL #
CONTENTS
Terminal No.
SELECT ITEM
000 - 254
MRS
000
NOTE
000 : Self terminal No.
This means local device.
1-254: Except self terminal No.
This means re-routed device.
Re-routing programming is only valid for printer.
CHANNEL#
Channel No.
0-7
0
0
:No RS232 cannel is assigned.
1-7 :RS232 channel is assigned.
PRINTER NAME
Connected printer name
SHARP ER-01PU
★
SHARP ER-03RP/04RP
EPSON TM-300
EPSON TM-T80
EPSON TM-T88/85
EPSON TM-U200
EJ FILE
AUTO CUTTER
Auto cutter function
No
★
Yes
PAPER SHEET
Paper sheet type selecting
ONE SHEET
TWO OR MORE
★
[1 DEVICE ASSIGN] - [2 R PRINTER] - [3 BILL PRINTER] - [4 REPORT PRINTER]
- [5 KP#1] - [6 KP#2] - [7 KP#3] - [8 KP#4] - [9 KP#5]
- [10 KP#6] - [11 KP#7] - [12 KP#8] - [13 KP#9]
DISPLAY : Setting screen
DISPLAY
TERMINAL #
CONTENTS
Terminal No.
SELECT ITEM
000 - 254
MRS
000
NOTE
000 : Self terminal No.
This means local device.
1-254: Except self terminal No.
This means re-routed device.
Re-routing programming is only valid for printers.
CHANNEL#
Channel No.
0-7
0
0
:No RS232 cannel is assigned.
1-7 :RS232 channel is assigned.
PRINTER NAME
Connected printer name
SHARP ER-01PU
★
SHARP ER-03RP/04RP
EPSON TM-300
EPSON TM-T80
EPSON TM-T88/85
EPSON TM-U200
AUTO CUTTER
Auto cutter function
No
★
Yes
PAPER SHEET
Paper sheet type selecting
ONE SHEET
TWO OR MORE
★
[1 DEVICE ASSIGN] - [14 CAT#1]
DISPLAY : Setting screen
DISPLAY
TERMINAL #
CONTENTS
Terminal No.
SELECT ITEM
000 - 254
MRS
000
NOTE
000 : Self terminal No.
This means local device.
1-254: Except self terminal No.
This means re-routed device.
CHANNEL#
Channel No.
0-7
0
0
:No RS232 cannel is assigned.
1-7 :RS232 channel is assigned.
[1 DEVICE ASSIGN] - [15 CAT#2] - [16 CAT#3]
- [17 SCALE] - [18 COIN DISP.] - [19 ONLINE]
DISPLAY : Setting screen
DISPLAY
CHANNEL#
CONTENTS
Channel No.
SELECT ITEM
0-7
MRS
0
NOTE
0
:No RS232 cannel is assigned.
1-7 :RS232 channel is assigned.
[1 DEVICE ASSIGN] - [20 CVM DATA I/F]
DISPLAY : Setting screen
DISPLAY
TERMINAL #
CONTENTS
Terminal No.
SELECT ITEM
000 - 254
MRS
000
NOTE
000 : Self terminal No.
This means local device.
1-254: Except self terminal No.
This means re-routed device.
CHANNEL#
Channel No.
0-7
0
0
:No RS232 cannel is assigned.
1-7 :RS232 channel is assigned.
2. [2 SYSTEM PRESET]
DISPLAY: Setting item select screen
Select “2 SYSTEM PRESET” and press the ENTER key.
DISPLAY: SYSTEM PRESETscreen
Select the job# to be changed and enter the value
The content of each job is described below.
[JOB#901] : MRS=0002
[JOB#904] : MRS=0000
901-A:
Not used (Fixed at "0")
904-A:
901-B:
1. Tax system
1. Printing of date
1. Tax system
901-C:
Yes
No
901-B
Auto tax 1-4 & manual tax
0
CANADIAN TAX (Type to Type 10)
6
CANADIAN TAX (Type 11)
7
★
904-B:
1. Printing of the consecutive No.
Yes
No
901-C
Normal
0
Singapole
8
0
1
0.00
2
0.000
3
★
1. Taxable 4 subtotal print on X/Z report
2. Gross Tax 4 and refund Tax 4 total print on X/Z report
3. Net Tax 4 total print on X/Z report
1. Taxable 4
subtotal
2. Gross Tax 4
and refund
Tax 4 total
3. Net Tax 4 total
905-A
Print
Skip
Print
Skip
Print
Skip
Print
Skip
Print
Print
[JOB#902] : MRS=0000
902-A:
Skip
1.In-line system
1.In-line system
902-A
No
0
Yes
1
Print
★
Skip
Skip
902-B,C,D: Not used (Fixed at "000")
905-B:
[JOB#903] : MRS=4000
903-A:
1. POS data copy baud rate
1. Baud rate
903-B:
2
4800
3
9600
4
19200
5
38400
6
57600
7
115200
8
903-C:
0
"KG"
2
Print
Print
Skip
1. GST EXPT
905-C
0
4
Print
Skip
905-D:
0
1
2
3
4
5
6
7
★
1. GST EXPT print on X/Z report
★
1. Entry of tare (For automatic system only)
★
905-B
Print
Skip
Print
Skip
Print
Skip
Print
Skip
Skip
903-B
"LB"
3. Tax is zero
Skip
★
905-C:
1. Symbol of scale entry
2. GST is
VAT
Print
1. Symbol of scale entry
0
1
2
3
4
5
6
7
1. Tax printing when taxable subtotal is zero.
2. Tax printing when GST is VAT.
3. Tax printing when tax is zero.
1. Taxable
subtotal is zero
903-A
2400
★
[JOB#905] : MRS=0005
901-D
0.0
904-B
0
4
904-C,D: Not used (Fixed at "00")
905-A:
0
★
★
1.TAB setting
1.TAB setting
904-A
0
4
1. Printing of the consecutive No.
1.Rounding system
1.Rounding system
901-D:
1. Printing of date
★
1. TAX METHOD (CANADIAN TAX)
2. Unit of weight for the scale
1. Entry of tare
Disallowed
Allowed
903-D:
Not used (Fixed at "0")
2. Unit of weight for
the scale
GST
903-C
2id(3id)+2dd
0
1id(2id)+3dd
1
2id(3id)+2dd
2
1id(2id)+3dd
3
★
PST
Tax on Tax
Tax on Base
Tax on Tax
Tax on Base
Tax on Tax
Tax on Base
Tax on Tax
Tax on Base
Tax on Tax
Tax on Base
0
1
2
3
4
5
6
7
8
9
★
908-B:
[JOB#906] : MRS=0030
906-A:
1. Printing of Dept. and PLU code
GT print on X report
1. GT1 (NET)
2. GT2 (+)
2. Entry which makes the PLU stock counter negative
1. Printing of Dept.
and PLU code
No
Yes
906-B:
2. Entry which makes the PLU
stock counter negative
0
Operation allowed despite
error message
1
Entry inhibited
2
Allowed unconditionally
4
Operation allowed despite
error message
5
Entry inhibited
6
Print
★
Skip
Print
Print
908-C:
Disable
0
Enable
2
★
Multiplication
0
FFx (FF sequence + Split pricing)
3
908-D:
★
906-D
No
0
Yes (3 digit decimal place)
1
No
2
Yes (3 digit decimal place)
3
★
Journal only
0
1
909-B:
[JOB#908] : MRS=0000
Skip
Skip
No
0
Yes
1
No
4
Yes
5
★
908-D
Disable
0
Enable
1
Disable
4
Enable
5
★
3. GT3 (–)
908-A
Print
0
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
909-C:
★
909-A
Print
0
Skip
1
Print
2
Skip
3
★
1. Printing of data on PLU resetting report
1. Printing of data on PLU resetting report
909-B
Print
0
Skip
4
GT print on Z report
Print
7
2. Printing of training GT
on the Z report
Print
★
Not used (Fixed at "0")
Skip
Print
1. Printing of training GT on the X report
Skip
907-C
Enable
Print
6
[JOB#909] : MRS=2000
1. Printing of training
GT on the X report
Disable
Print
5
Skip
2. Printing of training GT on the Z report
1. Minus Dept./PLU
2. GT2 (+)
4
1. Printing of X/Z report
(Excepting the individual server report)
Receipt & Journal
2. Fractional quantity
1. Minus Dept./PLU
1. GT1 (NET)
Skip
Print
1.Printing of X/Z report 2.Z1 resetting that resets GT
907-A,B: Not used (Fixed at "00")
908-A:
3
2. Z1 resetting that resets GT
[JOB#907] : MRS=0010
907-D:
2
★
906-C
909-A:
907-C:
Skip
Print
908-C
Yes
2. Fractional quantity
No
1
2. Resetting of
consecutive number in
Z1 resetting
No
1. Presetting of consective No.
Yes
0
Print
1. Add void -mode transaction data to hourly total report
1. Add void -mode
transaction data to
hourly total report
1. Multiplication entry
1. Presetting of
consective No.
908-B
Skip
2. Resetting of consecutive number in Z1 resetting
906-B
1. Multiplication entry
906-D:
Skip
1. Hash department setting
1. Hash department setting
906-C:
Skip
906-A
Allowed unconditionally
3. GT3 (–)
★
1. Printing of VOID mode totalizer and MGR VOID totalizer
on Z2 report
2. Printing of VOID mode totalizer and MGR VOID totalizer
on Z1 report
1. Printing of VOID
mode totalizer and
MGR VOID
totalizer on Z2
report
2. Printing of VOID mode
totalizer and MGR
VOID totalizer on Z1
report
Print
Skip
909-D:
Not used (Fixed at "0")
908-C
Print
0
Skip
2
Print
4
Skip
6
★
[JOB#910] : MRS=0024
[JOB#912] : MRS=0061
910-A:
912-A:
1. Drawer open at server sign ON/OFF
1. Drawer open at server sign ON/OFF
1. Data print format
910-A
No
0
Yes
2
1. Data print format
★
Note: For stay down server# entry system.
910-B:
Not used (Fixed at "0")
910-C:
1. Server # entry system
912-B:
0
Day / Month / Year
1
Year / Month / Day
2
910-C
Stay down
0
Auto sign off
2
★
912-C:
★
1. Time system
1. Time system
2. Server # entry system
910-D:
912-A
Month / Day / Year
912-B
12 H
0
24 H
1
★
1. After transaction receipt
2. Copy receipt function
Not used (Fixed at "4")
3. Footer print control (SRV JOB 912-D=2)
[JOB#911] : MRS=0000
911-A:
1. After
transaction
receipt
Fraction
1.
treatment
1. Fraction treatment
911-A
Round off
0
Round up
1
Round down
2
★
All receipts
0
On selected function key
at the time of finalization
1
All receipts
2
Yes
On selected function key
at the time of finalization
3
1. RECEIPT/SLIP header format
1. RECEIPT/SLIP header format
911-D
Format 1
0
Format 2
2
Format 3
4
★
HEADER FORMAT for order receipt (Receipt/Journal/Bill)
All receipts
4
No
On selected function key
at the time of finalization
5
All receipts
6
Yes
On selected function key
at the time of finalization
7
Detail
912-D:
Date / Machine No.
CC-No. / Time /
Server name / Server code
Format 2:
0 1 / 0 1 / 2 0 0 0
123456
#0 1 2 3 12:34AM JACK____0001
Date / Machine No.
CC-No. / Time /
Server name / Server code
Format 3:
123456
0 0 0 1
1
STAMP LOGO and 3-line footer
2
3-line header instead of a STAMP LOGO
3
3-line header instead of a STAMP LOGO and 3-line
footer
5
1
2
Date / Machine No.
CC-No. / Time /
Server code
Format 1:
Date / Machine No. / Bill#
CC-No. / Time /
Server name / Server code
Format 2:
01/01/2000
123456
BILL#0001
12:34AM JACK____0001
Date / Machine No. / Bill#
CC-No. / Time /
Server name / Server code
Format 3:
01/01/2000 123456
#0 1 2 3 12:34AM
BILL#0001
0 0 0 1
Date / Machine No. / Bill#
CC-No. / Time /
Server code
★
(STAMP LOGO message format)
HEADER FORMAT for GLU receipt (Receipt/Journal)
01/01/2000 123456
BILL#0001
#0123
12:34AM JACK____0001
0
STAMP LOGO only
0
0 1 / 0 1 / 2 0 0 0
#0 1 2 3 12:34AM
#0 1 2 3
912-D
3-line header instead of a STAMP LOGO
0 1 / 0 1 / 2 0 0 0
123456
#0123
12:34AM JACK____0001
★
1. STAMP LOGO message control
1. STAMP LOGO message control
Format 1:
912-C
No
Total only
911-B, C: Not used (Fixed at "00")
911-D:
2. Copy
3. Footrer print control
receipt
function
Note: STAMP LOGO applies to ER-01PU only.
3
5
914-B:
[JOB#913] : MRS=0104
913-A:
Not used (Fixed at "0")
913-B:
1. No-sale after non-add code entry
1.No-sale after non-add code entry
1. Printing of SBTL
0
Enable
1
2. Printing of MDSE SBTL
914-C:
3. Escape compulsory bill print operation
1.Printing of
SBTL
2.Printing of
MDSE
SBTL
3.Escape
compulsory bill
print
No
0
Enable
1
Disable
2
Enable
3
No
Yes
No
Disable
4
Enable
5
Disable
6
Enable
7
Yes
Yes
913-C:
★
1. VOID mode
2. Non-add code entry at the begining of a transaction
operation
913-B
Disable
914-B
Disable
1. VOID 2. Non-add code entry at the begining of a
mode
transaction operation
★
Enable
Disable
914-D:
914-C
Non-compulsory
0
Compulsory
1
Non-compulsory
2
Compulsory
3
★
1. Manual TAX
2. Check/Cashing
3. Non-add code entry
1. Lock error buzzer keeps sounding
1.Manual TAX
2.Check/Cashing
3.Non-add
code
entry
2. Buffered keyboard
1. Lock error buzzer
keeps sounding
2. Buffered keyboard
Disable
For 2 sec.
Yes
0
No
1
Yes
Constant
913-D:
913-C
No
★
Enable
Enable
914-D
Enable
0
Disable
1
Enable
2
2
Disable
3
3
Enable
4
Disable
Disable
1. Drawer closing compulsory
Enable
2. Error system
Disable
5
Enable
6
Disable
7
★
3. Key touch sound
1. Drawer closing
compulsory
2. Error system
All lock error
Non-compulsory
Misoperation
(One shot error)
All lock error
Compulsory
Misoperation
(One shot error)
3. Key touch
sound
913-D
Yes
0
No
1
Yes
2
No
3
Yes
4
No
5
Yes
6
No
7
[JOB#915] : MRS=0040
915-A:
1.Amount symbol
"
915-B:
915-C:
3. Tax delete
Yes
Yes
No
Yes
No
No
3. Tax
delete
Inhibit
0
Enable
1
Inhibit
2
Enable
3
Inhibit
4
Enable
5
Inhibit
6
Enable
7
2
1. PO system
915-B
Mixed entry
0
Cash only entry
1
1. Paper near end check (ER-01PU only)
3. RA system
2.No. of times of
ST(–) or ST(%)
entry within one
transaction
Any No. of times
★
★
2. No. of times of ST(–) or ST(%) entry within one transaction
1.Paper
near
end
check
914-A
★
1
1.PO system
2. No-sale key separation from CA/AT key for no-sale
function
2. No-sale key separate
from CA/AT key for
no-sale function
0
"
"(Space)"
★
1. Receipt issuing at no-sale
1. Recipt
issuing
at
no-sale
915-A
"$"
[JOB#914] : MRS=1100
914-A:
1. Amount symbol
Yes
Only once
Any No. of times
No
Only once
915-D:
Not used (Fixed at "0")
3.RA system
915-C
Mixed entry
0
Cash only entry
1
Mixed entry
2
Cash only entry
3
Mixed entry
4
Cash only entry
5
Mixed entry
6
Cash only entry
7
★
917-B:
[JOB#916] : MRS=1400
916-A:
916-B:
2. Printing of Gross Tax 2 and Refund Tax 2 totals on X/Z
report
1. Action to be taken when text and amount over lap each
other in a REG mode entry
1.Action to be taken when text and
amount over lap each other in a REG
mode entry
Truncate text
2-line print
1. Finalization by charge when ST
0
1.Finalization by charge when ST
Inhibit
Allow
0
1. Printing of Taxable 2 subtotal on X/Z report
3. Printing of Net Tax 2 total on X/Z report
916-A
0
1
1.Taxable 2
subtotal
2.Gross Tax 2 and
Refund Tax 2 totals
Print
★
Print
Skip
916-C:
916-B
0
4
★
Print
Skip
1. Negative merchandise subtotal
Skip
2. Subtotal entry before tender
917-C:
3. Subtotal entry before direct non-tendering finalization
1.Negative
merchandise
subtotal
Enable
Disable
916-D:
2.Subtotal entry
before tender
3.Subtotal entry
before direct
non-tendering
finalization
Non-compulsory
Non-compulsory
Compulsory
Non-compulsory
Compulsory
Compulsory
Non-compulsory
Non-compulsory
Compulsory
Non-compulsory
Compulsory
Compulsory
916-C
0
1
2
3
4
5
6
7
★
Print
Print
Skip
Print
Skip
Skip
2.Gross Tax 3 and
Refund Tax 3 totals
Print
Print
Skip
Print
Skip
Skip
917-D:
916-D
0
1
2
3
4
5
6
7
1.Total
Tax
2.Gross manual Tax and
Refund manual Tax
Print
Print
Skip
Print
Skip
2. Printing of Gross Tax 1 and Refund Tax 1 totals on X/Z
report
3. Printing of Net Tax 1 total on X/Z report
Print
Print
Skip
Print
Skip
Skip
3.Net Tax 1
total
Print
Skip
Print
Skip
Print
Skip
Print
Skip
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
917-A
0
1
2
3
4
5
6
7
3.Net Tax 3
total
917-C
Print
0
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
★
3. Printing of Net manual Tax total on X/Z report
★
1. Printing of Taxable 1 subtotal on X/Z report
2.Gross Tax 1 and
Refund Tax 1 totals
Print
★
1. Printing of Total Tax on X/Z report
Skip
1.Taxable 1
subtotal
1
2. Printing of Gross manual Tax and Refund manual Tax
on X/Z report
[JOB#917] : MRS=0000
917-A:
0
Skip
1. Printing of Taxable 3 subtotal on X/Z report
1.Taxable 3
subtotal
3. Check change total printing on X/Z report
3.Check
change total
Print
Skip
Print
Skip
Print
Skip
Print
Skip
Print
3. Printing of Net Tax 3 total on X/Z report
2. Net sales subtotal(NET1) printing on X/Z report
2.Net sales
subtotal(NET1)
917-B
2. Printing of Gross Tax 3 and Refund Tax 3 totals on X/Z
report
1. Coupon PLU printing on X/Z report
1.Coupon PLU
3.Net Tax 2
total
★
3.Net manual
Tax total
917-D
Print
0
Skip
1
Print
2
Skip
3
Print
4
Skip
5
Print
6
Skip
7
★
[JOB#918] : MRS=2233
[JOB#919] : MRS=5100
918-A:
919-A:
1. Printing of text for associated PLU in COMBO MEAL.
1. GLU/PBLU system
2. GLU/PBLU code entry at re-order (When #919:B-1 is 0 "
Auto generation ")
2. Direct non-tendering finalization after previous tender
entry.
3. Output of COMBO MEAL to KP.
3.Output of
1.Printing of text 2.Direct
COMBO
non-tendering
for associated
MEAL to KP.
finalization
PLU in
after previous
COMBO
tender entry.
MEAL.
Disable
Disable
Enable
918-B:
COMBO
MEAL’s KP
1
By associated
PLU
2
COMBO
MEAL’s KP
3
By associated
PLU
4
COMBO
MEAL’s KP
5
By associated
PLU
6
COMBO
MEAL’s KP
7
919-B:
No
Yes
918-C:
★
Yes
No
918-D:
Yes
No
919-C:
Yes
Yes
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
★
919-B
Auto generation
0
Manual
1
Auto generation
4
Manual
5
0
1
2
3
919-D:
★
No
0
Yes
1
No
2
Yes
3
★
1. Conversion SBTL printing of native SBTL
★
1. Conversion SBTL
2. Foreign currency
printing of native SBTL
format
919-D
Decimal digits are printed
0
Omit digits lower than
tab position
1
Decimal digits are printed
4
Omit digits lower than
tab position
5
Yes
No
★
[JOB#920] : MRS=2040 : INLINE PROGRAMMING
AREA
★
920-A:
1. Back-up master function.
1. Back-up master function.
Not
Exist
918-D
0
1
2
3
4
5
6
7
919-C
2. Foreign currency format
918-C
0
1
2
3
2. Amount printing when
PLU unit price is $0.00
Compulsory
918-B
920-B:
No
2. Guest check
No. system
Non-compulsory
3. Printing of tip totalizer on the server report
3.Printing of tip
totalizer on the
server report
5
1. PB entry
1. PB entry
2. Clearing of tip totalizer at server Z1 report
2.Clearing of tip
totalizer at
server Z1
report
Compulsory
2. Amount printing when PLU unit price is $0.00
1. Tip paid includes cash tip
1.Tip paid
includes
cash tip
4
1. Checking of server# on guest
check when a re-order is
made
2. Printing the DEPT./PLU text on KP in double size character
2.Printing the DEPT./PLU text
on KP in double size
character
Normal size
Double size
Normal size
Double size
3
Non-compulsory
1. Checking of server# on guest check when a re-order is
made
1. Kitchen printer recapitulation
1.Kitchen printer
recapitulation
2
Compulsory
2. Guest check No. system
2. Fractional entries for non-scalable PLU/DEPT.
2.Fractional entries for
non-scalable
PLU/DEPT.
Enable
Disable
Enable
Disable
Non-compulsory
Guest Look-Up system
1. Red color printing on KP when PLU’s unit price is zero
1.Red color printing on
KP when PLU’s unit
price is zero
919-A
PB Look-Up system
0
Skip
2. GLU/PBLU code entry
at re-order
918-A
By associated
PLU
Print
Enable
1. GLU/PBLU system
★
1. System report and down-load job is executed in the
back-up master
1. System report and down-load job is executed in
the back-up master
Disable
Enable
★
920-A
2
3
920-B
0
4
★
920-C:
922-C,D: 1. Programming of the SRN transmission speed and carrier-off waiting time
1. Broadcast communication (in-line)
2. PGM-mode programming at the satellite
1. Broadcast
communication
Exist
By terminal No.
920-D:
2. PGM-mode programming
at the satellite
Disable
Enable
Disable
Enable
Transmission speed
0
1
4
5
480 kbps
★
1 Mbps
1. The register is
1. The register is
Standard alone machine
Satellite
Master
Back up master
920-D
0
1
2
3
921-A:
Not used (Fixed at "0")
921-B:
1. GLU system
922-CD
01
02
04
00
09
10
12
08
★
★
[JOB#923] : MRS=0010 : INLINE PROGRAMMING
AREA
923-A,B: 1. The record number for REQUEST of T-LOG POLLING
(x100)
[JOB#921] : MRS=0000
1. The record number for REQUEST of T-LOG
POLLING (x100)
0000 ~ 9900
2. Drive thru system
923-AB
00-99
Explanation for satellite:
3. Drive thru entry
1. GLU system
Carrier-off waiting time
3.2 msec
6.4 msec
9.6 msec
12.8 msec
1.6 msec
3.2 msec
4.8 msec
6.4 msec
920-C
2. Drive thru
system
3. Drive thru entry
Non-compulsory
Compulsory
Non-compulsory
Compulsory
Non-compulsory
Compulsory
Non-compulsory
Compulsory
Centralized
Centralized
Individual
Centralized
Individual
Individual
Ex: When AB=10 The satellite will request to the master to poll the
T-log when the T-log records exceed 1,000.
921-B
0
1
2
3
4
5
6
7
★
923-C:
1. Electronic Journal resetting.
2. T-log function.
1. Electronic Journal
resetting.
Enable
Disable
921-C:
Not used (Fixed at "0")
921-D:
1. Tip paid is automatically executed when tip is remained
at individual server resetting.
923-D:
2. Drive thru
machine location
Cashier Station
Order Taker
Counter
Cashier Station
Order Taker
Counter
Yes
No
0
1
No
4
Yes
5
922-A,:
Not used (Fixed at "0")
922-B :
1. Using new Coin Dispenser which can issue $1 Coin.
★
1. Polling cycle (second)
923-D
No
0
1
0~9
924-A,B,C: Not used (Fixed at "143")
924-D:
Programming whether or not to lock REG-mode entries
after individual periodic total resetting
1. Locking after Daily Net resetting
2. Locking after Transaction resetting
1. Locking after Daily
Net resetting
Yes
No
922-B
Yes
★
[JOB#924] : MRS=1433 : INLINE PROGRAMMING
AREA
921-D
[JOB#922] : MRS=0008 : INLINE PROGRAMMING
AREA
1. Using new Coin Dispenser which can
issue $1 Coin.
No
Yes
0 ~ 9 Sec.
0
1
2
4
5
6
923-C
1. Polling cycle (second)
2. Drive thru machine location
1. Tip paid is automatically
executed when tip is
remained at individual
server resetting.
2. T-log function.
★
2. Locking after
Transaction resetting
924-A
Yes
0
No
1
Yes
2
No
3
★
[JOB#925] : MRS=0303 : INLINE PROGRAMMING
AREA
925-A:
Not used (Fixed at "0")
925-B:
1. Various individual resetting
1. Various individual resetting
925-C:
2
Enable
3
3. Send AT
command
string at
OPEN
STORE
2. Send AT
command
string at
CLOSE
STORE
No
925-B
Disable
No
★
Yes
1. Report printing when consolidation daily and periodic
transaction reading or resetting is taken
1. Report printing when consolidation daily and
periodic transaction reading or resetting is taken
Printing of both i.e. reports on individual machines
and consolidation report on the entire system
Printing of consolidation report on the entire system
Printing of report on individual register
925-D:
1. Open store /
Close store :
stand alone
POS with on-line
No
Yes
925-C
0
Yes
★
926-D:
1
2
926-C
No
0
Yes
1
No
2
Yes
3
No
4
Yes
5
No
6
Yes
7
★
1. Reverse ONLINE channel in closed store.
1. Reverse ONLINE channel in closed
store.
1. Resetting is allowed when the server is remained
signed on
926-D
No
0
Yes
4
★
2. Resetting in the open store state
1. Resetting is allowed when
the server is remained signed
on
No
Yes
2. Resetting in
the open
store state
Disable
Enable
Disable
Enable
[JOB#927] : NOT USED MRS=0000
925-D
[JOB#928] : MRS=0060
0
1
2
3
928-A,B: Not used (Fixed at "00")
928-C:
★
[JOB#926] : MRS=4000
926-A:
1. Printing of PLU on bill when it is 0
2. Printing of text for associated PLU in COMBO MEAL on
bill.
1. Printing of PLU
on bill when it is 0
1. Printing "LAST VOID DATA" on KP.
2. Printing "PAST VOID DATA" on KP.
1. Printing "LAST VOID
DATA" on KP.
2. Printing "PAST VOID
DATA" on KP.
Both are printed
Both LAST VOID DATA
and voided item aren’t
printed
926-B:
0
Both PAST VOID DATA
and voided item aren’t
printed
1
Both are printed
2
Both PAST VOID DATA
and voided item aren’t
printed
3
★
No
928-D:
928-C
Yes
0
No
2
Yes
4
No
6
★
1. Compulsory bill print system
1. Compulsory bill print system
928-D
According to each media’s preset
(The bill printing at service and final in GLU system
acts on PGM2 preset.
0
Compulsory every entry
1
Compulsory for PB entry
2
1. Sending "REFUND DATA" on KP.
1. Sending "REFUND DATA" on KP.
926-C:
Yes
926-A
Both are printed
2. Printing of text for
associated PLU in
COMBO MEAL on bill.
★
926-B
Yes
0
No
2
★
[JOB#929] : MRS=0000
929-A:
1. Open store / Close store : stand alone POS with on-line
1. KP print format when finalizing (Expeditor)
1. KP print format when finalizing
929-A
2. Send AT command string with OPEN STORE
Simple
0
3. Send AT command string with CLOSE STORE
Detail
1
★
NOTE:
Based on media preset.
929-B:
1. Server, Transaction resetting allowed with open GLU.
1. Server, Transaction resetting allowed
with open GLU.
No
Yes
929-C:
929-B
0
1
★
1. When closed file is full
1. When closed file is full
Inhibit registration
Registration is continued
929-C
0
1
★
929-D:
1. Selection of method of Presenting the TAX contents on
bill.
1. Selection of method of Presenting the
TAX contents on bill.
3. [3 Z REPORT COUNTER]
DISPLAY: Setting item select screen
929-D
The total of tax amount is printed.
0
The tax amount of every TAX is printed in
detail.
4
★
[JOB#980] : MRS=0000
980-A:
Not used (Fixed at "0")
980-B:
1. Hash department effect Hourly sales total.
1. Hash department effect Hourly sales
total.
980-B
No
0
Yes
1
★
Select “3 Z REPORT COUNTER” and press the ENTER key.
980-C,D: Not used (Fixed at "00")
[JOB#981] : MRS=4000
981-A:
DISPLAY: Z REPORT COUNTER screen
1. TAX amount display on screen.
1. TAX amount display on screen.
981-A
No
0
Yes
4
★
981-B,C,D: Not used (Fixed at "000")
Select the report to be changed and enter the value
The content of displayed reports are as listed in the
table below.
DISPLAY TEXT
CONTENTS
MRS
TRANSACTION Z1
Transaction Z1 report counter
0000
CONSOLI.TRN. Z1
Consolidation transaction Z1 report
counter
0000
SERVER Z1/Z2
Server Z1/Z2 report counter
0000
MANAGER Z1/Z2
Manager Z1/Z2 report counter
0000
HOURLY Z1
Hourly Z1 report counter
0000
PLU Z1/Z2
PLU Z1/Z2 report counter
0000
GLU Z1
GLU Z1 report counter
0000
Note :
GT programming will be inhibited after MRS-3 operation.
JOB#989 memory initial can be executed after MRS-3
operation.
GT1 is obtained by the following equation.
DRIVE THRU Z1
Drive thru Z1 report counter
0000
TRANSACTION Z2
Transaction Z2 report counter
0000
CONSOLI.TRN. Z2
Consolidation transaction Z2 report
counter
0000
DAILY NET Z2
Daily net Z2 report counter
0000
DEPARTENT Z1
DeparTent Z1 report counter
0000
DEPARTENT Z2
DeparTent Z2 report counter
0000
EQUATION: GT1 = GT2 – GT3
5. [5 MODE SECRET#]
DISPLAY: Setting item select screen
4. [4 GT]
DISPLAY:
Setting item select screen
Select "5 MODE SECRET#" and press the ENTER key.
DISPLAY: MODE SECRET# screen
Select "4 GT" and press the ENTER key.
DISPLAY: GT COUNTER screen
Select the mode to be changed and enter the value
The content of displayed secret# are as listed in the
table below.
DISPLAY TEXT
CONTENTS
MRS
OP XZ MODE
OP X/Z mode secret code (4 digits)
X1 MODE
X1 mode secret code (4 digits)
0000
Z1 MODE
Z1 mode secret code (4 digits)
0000
X2 MODE
X2 mode secret code (4 digits)
0000
Z2 MODE
Z2 mode secret code (4 digits)
0000
PRICE MODE
PRICE mode secret code (4 digits)
0000
PGM1 MODE
PGM1 mode secret code (4 digits)
0000
Select the GT to be changed and enter the value
PGM2 MODE
PGM2 mode secret code (4 digits)
0000
The content of displayed GT are as listed in the table
below.
AUTO KEY PGM
AUTO KEY mode secret code (4 digits)
0000
REG MODE
REG mode secret code (4 digits)
0000
START UP
START UP secret code (4 digits)
0000
DISPLAY TEXT
CONTENTS
MRS
POSITIVE GT
GT2 (Positive GT) : Max. 13digits
0.00
NEGATIVE GT
GT3 (Negative GT) : Max. 13digits
0.00
TRAINING GT
Training GT : Max. 13digits
0.00
*:
0000
If "0" is entered "compulsory secret code entry" is canceled.
6. [6 FREE KEY LAYOUT]
When forming keys: Select the key to be formed with the cursor and
press the key to be formed.
DISPLAY: Setting item select screen
With the cursor key,
the key No. is retrieved and
specified.
Retrieve and specification by
directly entering the key No.
XXX
With " " key and " "key,
the screen is selected and the
key No. specified
Select "6 FREE KEY LAYOUT" and press the ENTER key.
DISPLAY: FREE KEY LAYOUT
To view all functions, use the cursor key, or enter the key No. and
press the ENTER key.
Since key No. 1 ~ 25 are fixed, the initial screen starts from key No.
26.
ENTER
Key No.
With the above operation, the
screen is selected and the key No.
Press the key to be formed
<Key No. Table>
Key
No.
999
001
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
Function name
INHIBIT
0KEY
1KEY
2KEY
3KEY
4KEY
5KEY
6KEY
7KEY
8KEY
9KEY
00KEY
000KEY
DECIMAL POINT
CLEAR
@/FOR
SUB TOTAL
MODE
CURSOR UP
CURSOR DOWN
CURSOR LEFT
CURSOR RIGHT
CANCEL
ENTER
CA/AT
PAGE UP
PAGE DOWN
BACK SPACE
DELETE
MERCHANDISE SUB-TOTAL
TRAY SUB-TOTAL
NON ADD
NO SALE
SCALE
PLU/SUB
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
key text
INHIBIT
0KEY
1KEY
2KEY
3KEY
4KEY
5KEY
6KEY
7KEY
8KEY
9KEY
00KEY
000KEY
.KEY
CL
X
SBTL
MODE
UP
DOWN
LEFT
RIGHT
CANCEL
ENTER
CA/AT
P UP
P DOWN
BKSPC
DEL
MDS ST
TRY ST
#
NS
SCALE
PLU/SB
L1
L2
L3
L4
Position
code (MRS)
109
110
122
134
111
123
135
112
124
136
121
--133
137
125
146
155
086
085
073
097
099
098
145
101
100
----140
--------138
096
108
120
132
Key
No.
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
066
067
068
069
070
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
Function name
LEVEL 5
LEVEL 6
LEVEL 7
LEVEL 8
LEVEL 9
LEVEL 10
PRICE 1
PRICE 2
PRICE 3
PRICE 4
PRICE 5
TAX 1 SHIFT
TAX 2 SHIFT
TAX 3 SHIFT
TAX 4 SHIFT
BILL
COPY/AFTER TRANSACTION
RECEIPT
CHARGE TIP
CASH TIP
TIP PAID
LAST VOID
IN-DIRECT VOID
SUB-TOTAL VOID
REFUND
RETURN
%1
%2
%3
%4
%5
%6
%7
%8
%9
(-) 1
(-) 2
(-) 3
(-) 4
(-) 5
(-) 6
(-) 7
(-) 8
(-) 9
TAX
COVER COUNT
AUTO
AUTO 2
AUTO 3
AUTO 4
AUTO 5
AUTO 6
AUTO 7
AUTO 8
AUTO 9
AUTO 10
AUTO 11
AUTO 12
AUTO 13
AUTO 14
L5
L6
L7
L8
L9
L10
P1
P2
P3
P4
P5
TAX1SF
TAX2SF
TAX3SF
TAX4SF
BILL
RCPT
Position
code (MRS)
144
--------------------119
131
----118
117
CH TIP
CA TIP
TIP PD
VOID
I.VOID
ST VD
RFND
RETURN
%1
%2
%3
%4
%5
%6
%7
%8
%9
(-)1
(-)2
(-)3
(-)4
(-)5
(-)6
(-)7
(-)8
(-)9
TAX
CV CNT
AUTO
AUTO2
AUTO3
AUTO4
AUTO5
AUTO6
AUTO7
AUTO8
AUTO9
AUTO10
AUTO11
AUTO12
AUTO13
AUTO14
------102
114
126
141
--128
----------------116
--------------------143
142
-------------------------
key text
Key
No.
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
Function name
AUTO 15
AUTO 16
AUTO 17
AUTO 18
AUTO 19
AUTO 20
AUTO 21
AUTO 22
AUTO 23
AUTO 24
AUTO 25
CASH 2
CHECK
CHECK 2
CHECK 3
CHECK 4
CHARGE 1
CHARGE 2
CHARGE 3
CHARGE 4
CHARGE 5
CHARGE 6
CHARGE 7
CHARGE 8
CHARGE FOR EMPLOYEE
SALES
CURRENCY CONVERSION 1
CURRENCY CONVERSION 2
CURRENCY CONVERSION 3
CURRENCY CONVERSION 4
GLU/PBLU
DRIVE THRU (RE-ORDER)
NEW CHECK
DRIVE THRU (NEW CHECK)
SERVICE
FINAL
DEPOSIT
DEPOSIT REFUND
BILL TRANSFER
RECEIVED ON ACCOUNT
RECEIVED ON ACCOUNT 2
PAID OUT
PAID OUT 2
SERVER NUMBER
MANAGER NUMBER
EMPLOYEE NUMBER
EAT IN 1
EAT IN 2
EAT IN 3
REMOTE PRINTER SEND
GRATUITY EXEMPT
OPEN TARE
BALANCE
REPEAT
TRANS OUT
TRANS IN
SEAT NUMBER
INDIVIDUAL PAYMENT
EMPLOYEE SALES
MISC MENU
AUTO15
AUTO16
AUTO17
AUTO18
AUTO19
AUTO20
AUTO21
AUTO22
AUTO23
AUTO24
AUTO25
CA2
CHK
CHK2
CHK3
CHK4
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
EMP CH
Position
code (MRS)
---------------------------------------------------
CONV1
CONV2
CONV3
CONV4
PBAL
PBAL2
N.C.
N.C.2
SRVC
FINAL
DEPO
DEP.RF
B.T.
RA
RA2
PO
PO2
SRV#
MGR#
EMPL#
EATIN1
EATIN2
EATIN3
RP SND
GRT EX
OPN TR
BAL
REPEAT
TR.OUT
TR.IN
SEAT#
I.PAY
E.SALE
M.FUNC
--------152
--154
--151
150
----148
--------113
------------------------153
----156
key text
Key
No.
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
Function name
CHECK MENU
CHARGE MENU
CONVERSION MENU
RECEIPT ON/OFF
WAIT FOR DRIVE THRU
RE-CALL FOR DRIVE THRU
BILL SEPARATE
WASTE MODE
CONDIMENT NEXT
TIME-IN
TIME-OUT
BREAK
DRIVE THRU MENU
NEXT$
EDIT TIP
REPEAT ROUND
GLU RECALL
MESSAGE 1
MESSAGE 2
MESSAGE 3
MESSAGE 4
MESSAGE 5
MESSAGE 6
MESSAGE 7
MESSAGE 8
MESSAGE 9
MESSAGE MENU
PLU MENU 1
PLU MENU 2
PLU MENU 3
PLU MENU 4
PLU MENU 5
PLU MENU 6
PLU MENU 7
PLU MENU 8
PLU MENU 9
PLU MENU 10
PLU MENU 11
PLU MENU 12
PLU MENU 13
PLU MENU 14
PLU MENU 15
PLU MENU 16
PLU MENU 17
PLU MENU 18
PLU MENU 19
PLU MENU 20
PLU MENU 21
PLU MENU 22
PLU MENU 23
PLU MENU 24
PLU MENU 25
PLU MENU 26
PLU MENU 27
PLU MENU 28
PLU MENU 29
PLU MENU 30
PLU MENU 31
PLU MENU 32
PLU MENU 33
key text
CHK.MN
CHG.MN
CNV.MN
RCP.SW
WAIT
RECALL
B.S.
WASTE
C NEXT
T.IN
T.OUT
BREAK
D-DISP
NEXT$
ED TIP
RP.RND
GLU RC
MSG1
MSG2
MSG3
MSG4
MSG5
MSG6
MSG7
MSG8
MSG9
MSG.MN
PMEN01
PMEN02
PMEN03
PMEN04
PMEN05
PMEN06
PMEN07
PMEN08
PMEN09
PMEN10
PMEN11
PMEN12
PMEN13
PMEN14
PMEN15
PMEN16
PMEN17
PMEN18
PMEN19
PMEN20
PMEN21
PMEN22
PMEN23
PMEN24
PMEN25
PMEN26
PMEN27
PMEN28
PMEN29
PMEN30
PMEN31
PMEN32
PMEN33
Position
code (MRS)
127
139
--------149
------------147
--130
129
------------------115
-------------------------------------------------------------------
Key
No.
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
Function name
key text
PLU MENU 34
PLU MENU 35
PLU MENU 36
PLU MENU 37
PLU MENU 38
PLU MENU 39
PLU MENU 40
PLU MENU 41
PLU MENU 42
PLU MENU 43
PLU MENU 44
PLU MENU 45
PLU MENU 46
PLU MENU 47
PLU MENU 48
PLU MENU 49
PLU MENU 50
PMEN34
PMEN35
PMEN36
PMEN37
PMEN38
PMEN39
PMEN40
PMEN41
PMEN42
PMEN43
PMEN44
PMEN45
PMEN46
PMEN47
PMEN48
PMEN49
PMEN50
Position
code (MRS)
-----------------------------------
KEY POSITION CODE
12
24
36
48
60
72
84
96 108 120 132 144 156
11
23
35
47
59
71
83
95 107 119 131 143 155
10
22
34
46
58
70
82
94 106 118 130 142 154
9
21
33
45
57
69
81
93 105 117 129 141 153
8
20
32
44
56
68
80
92 104 116 128 140 152
7
19
31
43
55
67
79
91 103 115 127 139 151
6
18
30
42
54
66
78
90 102 114 126 138 150
5
17
29
41
53
65
77
89 101 113 125 137 149
4
16
28
40
52
64
76
88 100 112 124 136 148
3
15
27
39
51
63
75
87
99 111 123 135 147
2
14
26
38
50
62
74
86
98 110 122 134 146
1
13
25
37
49
61
73
85
97 109 121 133 145
7. [7 INIT. KEY LAYOUT]
DISPLAY: Setting item select screen
Select "7 INIT. KEY LAYOUT" and press the ENTER key.
The keyboard layout is reset to the standard layout.
8. [8 FILE]
DISPLAY: Setting item select screen
Select "8 FILE" and press the ENTER key.
Select the file name to be changed and enter the number of records.
The contents displayed are as listed in the file table.
DISPLAY: File group Type 3 input screen
DISPLAY : File group Type 0 input screen
DISPLAY TEXT
RECORD
SELECT ITEM
NOTE
CREATE
Select and press the LIST
Key.
ERASE
Select the CREATE /ERASE to be changed and enter
the number of records.
DISPLAY: File group Type 1 input screen
Enter the number of records.
When an item of Type 2 is selected, the following display is shown.
DISPLAY: File group Type 2 input screen
Enter the number of blocks.
Enter the number of records.
FILE TABLE
GROUP
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
FILE NAME
Dept
Dept Text (8)
Dept Text (16)
Dept Mark Down
PLU
PLU Price 1
PLU Price 1 to 5
PLU Text 1 (8)
PLU Text 1 (16)
PLU KP Text 1
PLU Text 1 to 5 (8)
PLU Text 1 to 5 (16)
PLU KP Text 1 to 5
PLU stock
Link PLU
COMBO MENU
COMBO KP TEXT
Condiment table
Mix & Match table
Recipe table
Ingredient table
Ingredient Stock
Server
Sign off Server for IRC
Manager
Employee
Employee Sales
Employee working time
Hourly
Hourly PLU Group
Service Time
Daily net
Reg buffer
KP buffer
GLU/PBLU (Preset + buffer)
Closed GLU
Drive Thru (Preset + buffer)
Closed Drive Thru
Auto GLU generate code
Auto Drive Thru generate code
GLU/PBLU Rcv.buffer (IRC)
KP
(IRC)
T-LOG Buffer
Journal Log buffer
Receipt Window buffer
Ind. Payment buffer
Term Dept
Term PLU
Term Transaction
Term Server
Term Manager
All of term file
GLU/PBLU file (Preset Only)
Drive thru file(Preset Only)
B.T. buffer (Buffer Only)
WAIT buffer
D-THRU RCP.WIN
Electronic Journal
Message Text
TYPE
1
0
0
0
1
0
0
0
0
0
0
0
0
0
1
1
0
1
1
1
1
0
1
2
1
1
3
3
1
0
0
1
1
0
3
3
3
3
1
1
2
1
1
1
1
0
0
0
0
0
0
0
3
3
0
2
1
1
0
* File table No. (Create/Erase)
01, 02, 03, 05
03
04
10
15, 16, 18, 25, 30, 35, 40, 45, 190
16, 25, 30, 35, 40, 45, 190
17, 50, 55, 60, 65, 70, 191
18
19
20
21
22
23
24
75
76, 77
78
81, 188
82, 83
84
85, 86
87
96, 97, 98, 99, 100
110, 111
112, 113, 114
119, 120
121
122
123, 124
128
132, 133
137, 138
143, 144, 145, 146, 179, 181, 184, 197, 198,
147, 199
157, 195, 196
158
159
160
161
162
148
169, 170
150
153
154
155, 156, 178, 180
06, 11
26, 31, 36, 41, 46
92
101
115
06, 11, 26, 31, 36, 41, 46, 92, 101, 115
157, 195, 196
159
146
183
185
194
192, 193
GROUP
NO.
60
61
Type 0
Type 1
Type 2
Type 3
FILE NAME
Repeat Round buffer
Employee working time 2
TYPE
0
3
* File table No. (Create/Erase)
198
200
Create/Erase only
Create/Erase and Increase/Decrease the number of
records.
Create/Erase and Increase/Decrease the number of
blocks.
Create/Erase and Increase/Decrease the number of
records for label and data individually.
: The files which are created or erased by the entry of the group
No.
: For individual erase
FILE CONTENTS
Table
No.
File Name
Record
MRS
Max
Block
#1
MRS
Max
#2
Label
Size
Data
Size
13
1
Dept. peset
10
99
1
1
1
2
Price
10
99
(1)
1
1
0
3
3
Text(8)
10
99
(1)
1
1
0
8
4
Text(16)
0
99
(1)
0
1
0
16
5
Daily
10
99
(1)
1
1
0
9
6
Term
10
99
(1)
1
1
0
9
7
Save Daily
0
99
(1)
0
1
0
9
8
Consoli.
0
99
(1)
0
1
0
9
9
Receive
0
99
(1)
0
1
0
9
10
Daily(markdown)
0
99
(1)
0
1
0
8
11
Term(markdown)
0
99
(1)
0
1
0
8
12
Save Daily(markdown)
0
99
(1)
0
1
0
8
13
Consoli.(markdown)
0
99
(1)
0
1
0
8
14
Receive(markdown)
0
99
(1)
0
1
0
8
37
15
PLU preset
500
*****
1
1
5
16
Price1
500
*****
(16)
0
1
0
3
17
Price1-5
0
*****
(16)
1
1
0
15
18
Text1(8)
500
*****
(16)
0
1
0
8
19
Text1(16)
0
*****
(16)
0
1
0
16
20
KP text1
500
*****
(12)
0
1
0
12
21
Text1-5(8)
0
*****
(16)
1
1
0
40
22
Text1-5(16)
0
*****
(16)
0
1
0
80
60
23
KP text1-5
0
*****
(12)
1
1
0
24
Stock
0
*****
(16)
0
1
0
8
25
Daily(price1)
500
*****
(16)
0
1
0
9
26
Term(price1)
0
*****
(16)
0
1
0
9
27
Save Daily(price1)
0
*****
(16)
0
1
0
9
28
Consoli.(price1)
0
*****
(16)
0
1
0
9
29
Receive(price1)
30
COMBO Daily(price1)
31
32
33
34
0
*****
(16)
0
1
0
9
500
*****
(16)
0
1
0
9
Term(price1)
0
*****
(16)
0
1
0
9
Save Daily(price1)
0
*****
(16)
0
1
0
9
Consoli.(price1)
0
*****
(16)
0
1
0
9
Receive(price1)
0
*****
(16)
0
1
0
9
500
*****
(16)
0
1
0
9
Term(price1)
0
*****
(16)
0
1
0
9
37
Save Daily(price1)
0
*****
(16)
0
1
0
9
38
Consoli.(price1)
0
*****
(16)
0
1
0
9
35
WASTE Daily(price1)
36
Table
No.
39
File Name
Receive(price1)
Record
Block
MRS
Max
#1
MRS
Max
#2
Label
Size
Data
Size
0
*****
(16)
0
1
0
9
500
*****
(16)
0
1
0
9
Term(price1)
0
*****
(16)
0
1
0
9
42
Save Daily(price1)
0
*****
(16)
0
1
0
9
43
Consoli.(price1)
0
*****
(16)
0
1
0
9
40
REFUND Daily(price1)
41
44
Receive(price1)
45
COUPON Daily(price1)
46
Term(price1)
0
*****
(16)
0
1
0
9
500
*****
(16)
0
1
0
9
0
*****
(16)
0
1
0
9
47
Save Daily(price1)
0
*****
(16)
0
1
0
9
48
Consoli.(price1)
0
*****
(16)
0
1
0
9
49
Receive(price1)
0
*****
(16)
0
1
0
9
50
Daily(price1-5)
0
*****
(16)
5
5
0
9
51
Term(price1-5)
0
*****
(16)
0
5
0
9
52
Save Daily(price1-5)
0
*****
(16)
0
5
0
9
53
Consoli.(price1-5)
0
*****
(16)
0
5
0
9
54
0
*****
(16)
0
5
0
9
55
COMBO Daily(price1-5)
0
*****
(16)
5
5
0
9
56
Term(price1-5)
0
*****
(16)
0
5
0
9
57
Save Daily(price1-5)
0
*****
(16)
0
5
0
9
58
Consoli.(price1-5)
0
*****
(16)
0
5
0
9
Receive(price1-5)
9
59
Receive(price1-5)
0
*****
(16)
0
5
0
60
WASTE Daily(price1-5)
0
*****
(16)
5
5
0
9
61
Term(price1-5)
0
*****
(16)
0
5
0
9
62
Save Daily(price1-5)
0
*****
(16)
0
5
0
9
63
Consoli.(price1-5)
0
*****
(16)
0
5
0
9
Receive(price1-5)
9
64
0
*****
(16)
0
5
0
65
REFUND Daily(price1-5)
0
*****
(16)
5
5
0
9
66
Term(price1-5)
0
*****
(16)
0
5
0
9
67
Save Daily(price1-5)
0
*****
(16)
0
5
0
9
68
Consoli.(price1-5)
0
*****
(16)
0
5
0
9
69
Receive(price1-5)
0
*****
(16)
0
5
0
9
70
COUPON Daily(price1-5)
0
*****
(16)
5
5
0
9
71
Term(price1-5)
0
*****
(16)
0
5
0
9
72
Save Daily(price1-5)
0
*****
(16)
0
5
0
9
73
Consoli.(price1-5)
0
*****
(16)
0
5
0
9
0
*****
(16)
30
99
74
Receive(price1-5)
0
5
0
9
1
1
1
15
75
Link PLU
76
COMBO MEAL
20
20
1
1
1
61
77
COMBO MEAL text
20
20
(77)
1
1
0
16
(12)
0
1
0
12
1
1
1
90
1
1
0
16
155
78
COMBO MEAL KP text
0
20
79
PLU MENU KEY
50
99
80
Text for PLU MENU
50
99
81
Condiment table
10
99
1
1
1
82
Mix & Match table
10
99
1
1
1
5
83
Mix & Match sale buffer
10
99
(83)
1
1
0
5
(80)
84
Recipe table
500
999
1
1
2
120
85
Ingredient table
999
999
(86)
1
1
2
3
86
Ingredient text
999
999
(86)
1
1
0
8
87
Ingredient stock
999
999
(86)
1
1
0
4
88
Ingredient Consoli.
0
999
(86)
1
1
0
4
89
Ingredient Receive
0
999
(86)
1
1
0
4
90
Transaction Label
143
143
1
1
2
0
91
Daily
143
143
(92)
1
1
0
8
92
Term
143
143
(92)
1
1
0
8
Table
No.
File Name
Record
MRS
Max
Block
#1
MRS
Max
#2
Label
Size
Data
Size
93
Save Daily
0
143
(92)
1
1
0
8
94
Consoli.
0
143
(92)
1
1
0
8
0
143
(92)
10
255
95
96
Receive
Server preset
1
1
0
8
1
1
2
23
97
Flag
10
255
(97)
1
1
0
3
98
Text
10
255
(97)
1
1
0
8
99
Server Trans. Label
76
76
10
255
(97)
2
0
100
Daily
76
76
(100)
10
255
(97)
0
8
Term
76
76
(100)
10
255
(97)
0
8
101
102
(not used)
103
(not used)
104
(not used)
105
Total server (Buffer) Label
76
76
(100)
1
1
2
0
106
Total
76
76
(100)
1
1
0
8
0
76
(100)
0
1
2
0
0
76
(100)
0
1
0
8
107
(not used)
108
(not used)
109
(not used)
110
Sign off Server Trans.Label
111
Receive
112
Manager
5
99
1
1
1
2
113
Manager Trans. Label
5
99
1
1
2
0
114
Daily
5
99
1
1
0
9
115
Term
5
99
1
1
0
9
116
Save Daily
0
99
0
1
0
9
117
Consoli.
0
99
0
1
0
9
0
99
0
1
0
9
20
****
1
1
5
21
118
119
Receive
Employee Label
120
Name
20
****
1
1
0
8
121
Employee Sales
20-40
****-****
(114)
1
1
5
17
122
Employee working time
20-100
****-****
1
1
5
23
123
Hourly Label
96
96
1
1
1
0
11
124
Daily
96
96
(118)
1
1
0
125
Save Daily
0
96
(118)
1
1
0
11
126
Consoli.
0
96
(118)
1
1
0
11
127
128
Receive
PLU group Daily
0
96
(118)
1
1
0
11
96
96
(118)
9
9
0
9
129
Save Daily
0
96
(118)
9
9
0
9
130
Consoli.
0
96
(118)
9
9
0
9
131
Receive
0
96
(118)
9
9
0
9
132
Service Time Label
24
24
1
1
1
0
133
Daily
24
24
1
1
0
11
(127)
134
Save Daily
0
24
(127)
1
1
0
11
135
Consoli.
0
24
(127)
1
1
0
11
(127)
1
1
0
11
1
1
3
0
136
0
24
137
Daily Net Label
Receive
32
32
138
Total
32
32
(132)
1
1
0
8
139
Daily Net Consoli. Label
0
32
(132)
1
1
3
0
0
32
(132)
1
1
0
8
0
32
(132)
1
1
3
0
0
32
(132)
1
1
0
8
1
1
0
48
140
141
Consoli.
Daily Net Receive Label
142
Receive
143
REG Buffer
250
*****
144
REG Edit Buffer
250
*****
(138)
1
1
0
48
145
GLU/PBLU Buffer
250
*****
(138)
1
1
0
48
Table
No.
Record
File Name
Block
MRS
Max
#1
MRS
Max
#2
Label
Size
Data
Size
146
B.T. Buffer
250
*****
(138)
1
1
0
48
147
KP Buffer
250
*****
(138)
1
1
0
48
148
GLU/PBLU Rcv. Buffer
0
*****
(138)
1
1
0
48
149
GLU/PBLU Save Buffer
(138)
150
T-Log Buffer
151
152
0
*****
1500
*****
1
1
0
48
1
1
0
26
T-Log Receive Buffer
0
*****
Sorted Top 20 Buffer
20
99
1
1
0
26
1
1
8
2
153
Journal Log Buffer
100
154
Receipt Window Buffer
30
***
1
1
0
50
***
1
1
3
155
Ind. Payment Edit Buffer
0
*****
23
(138)
1
1
0
156
Ind. Pay GLU/PBLU Buffer
0
*****
48
(138)
1
1
0
48
157
GLU/PBLU
50-500
****-****
158
Closed GLU
0
****-****
50-500
****-****
0
****-****
(138)
0
1
10
45
(238)
1
1
2
238
0
1
10
45
(238)
1
1
2
238
159
Drive Thru
160
Closed Drive Thru
161
Auto GLU Generate code
51
**
1
1
0
13
162
Auto Drive Thru Generate code
51
**
1
1
0
13
163
Logo Text
15
15
1
1
1
40
164
Function Text
217
217
1
1
2
8
165
Dept. Group Text
9
9
1
1
1
8
166
PLU Group Text
99
99
1
1
1
8
167
Hourly Group Text
9
9
1
1
1
8
168
Currency Descriptor
4
4
1
1
1
4
169
KP Preset
9
9
170
KP Text
9
9
171
Job Location Table
99
99
172
Job Location Text
99
99
173
Direct key Table
65
174
Scale Table
9
175
Auto key table
176
1
1
1
4
1
1
0
12
1
1
1
6
1
1
0
8
65
18
18
1
30
9
1
1
1
2
25
25
1
1
2
75
Stacked report Table
20
20
2
2
1
12
177
Employee time buffer
20
20
1
1
0
24
178
Ind. Payment REG Buffer
0
*****
(138)
1
1
0
48
179
Bill buffer
250
*****
(138)
1
1
0
48
180
Ind.Payment itemizer Buffer
0
100
1
1
1
345
181
Copy Buffer
250
****
(138)
1
1
0
48
182
D-thru/GLU Display buffer
250
****
(138)
4
1
0
29
183
D-thru/GLU Wait buffer
250
****
(138)
20
1
0
29
184
D-thru/GLU Previous Buffer
250
****
(138)
1
1
0
48
185
D-thru Order Machine Display buffer
250
****
1
1
0
23
186
B.S. Destination Buffer
30
***
1
1
3
18
187
B.S. Source Buffer
30
***
1
1
3
18
188
Condiment Edit Buffer
250
****
(138)
40
1
0
48
(164)
(167)
189
GLU/PBLU Rcv.2 Buffer
0
*****
(138)
1
1
0
48
190
PLU Top 20 Buffer (Price 1)
500
*****
(16)
0
1
0
9
191
PLU Top 20 Buffer(Price1-5)
0
*****
(16)
5
5
0
9
192
Message Preset
0
9
193
Message text
194
Electronic Journal
195
Open GLU Buffer
0
9
3000
****
(16)
0
1
0
30
1
1
0
16
Table
No.
Record
File Name
MRS
Max
196
Disp Open GLU Buffer
197
Receipt Window Disp Buffer
250
****
198
Repeat Round Buffer
250
****
199
Reg. Buffer For KP
250
****
200
Employee working time2
20-100
****-****
Block
#1
(17)
MRS
Max
#2
Label
Size
Data
Size
1
1
0
18
1
1
0
48
1
1
0
17
1
1
0
48
1
1
5
23
#1: Same as the number of record of table no. N
#2: Same as the number of block of table no. N
9. [9 SUPERVISR ON/OFF]
10. [10 MEMORY INITIAL]
DISPLAY: Setting item select screen
DISPLAY: Setting item select screen
Select "9 SUPERVISOR ON/OFF" and press the ENTER key.
DISPLAY: Supervisor ON/OFF screen
DISPLAY TEXT
SUPERVISOR MODE
DISPLAY: The following display is shown.
SELECT
ITEM
MRS
NOTE
OFF
★
Select and press the
LIST Key.
ON
Select "10 MEMORY INITIAL" and press the ENTER key.
Select the item and press the ENTER key.
Select the item.
11. [11 SSP]
12. [12 BACKUP SEND]
DISPLAY: Setting item select screen
DISPLAY: Setting item select screen
Select "11 SSP" and press the ENTER key.
DISPLAY: SSP screen
Select "12 BACKUP SEND" and press the ENTER key.
DISPLAY: BACKUP SEND screen
Select the item and press the ENTER key.
The contents of item are shown in the table below.
DISPLAY TEXT
SSP INPUT
CONTENTS
Used for SSP data input.
SSP EDIT
USED for edit of entered SSP data.
SSP ALL CLEAR
Used to erase all the entered SSP data.
SSP IND. CLEAR
Used to erase entered SSP data individually.
SSP REACTIV.
Used to restore erased SSP data.
Select the item and press the ENTER key.
The contents of items are shown in the table below.
DISPLAY
CONTENTS
SELECT ITEM
SEND
DATA
Send content
select
ALL RAM
SPEED
Comunication
speed setting
PROGRAMMED SPEED
MRS
★
SSP
115200 bps
57600 bps
38400 bps
19200 bps
9600 bps
4800 bps
2400 bps
★
13. [13 BACKUP RECEIVE]
CHAPTER 5. SRV MODE
PROGRAMMING
("3 IRC SETTING")
DISPLAY: Setting item select screen
DISPLAY: SRV mode screen
Select "13 BACKUP RECEIVE" and press the ENTER key.
DISPLAY: BACKUP RECEIVE screen
Select "3 IRC SETTING" and press the ENTER key.
DISPLAY: IRC SETTING item selection screen
Select the item and press the ENTER key.
The contents of items are shown in the table below.
DISPLAY
SPEED
CONTENTS
Comunication
speed setting
SELECT ITEM
PROGRAMMED SPEED
MRS
★
Select the item and press the ENTER key.
115200 bps
57600 bps
38400 bps
The item setting input screen is displayed.
19200 bps
9600 bps
4800 bps
1. [1 TERMINAL SETTING]
2400 bps
DISPLAY: Setting item select screen
Select the item to be changed and press the ENTER key.
The contents of setting are shown in the table below.
[1 SATELLITE]
[2 MASTER]
DISPLAY: Setting screen
DISPLAY: Setting screen
Select the item to be changed and press the ENTER key.
The setting content is described below.
DISPLAY TEXT
TERMINAL No.
GLU SYSTEM
CONTENTS
Terminal No.
GLU system
D-THRU SYSTEM
MACHINE LOCATION
BACKUP MASTER
SELECT ITEM MRS
000 ~ 254
000
CENTRALIZED
★
INDIVIDUAL
Drive thru system CENTRALIZED
★
INDIVIDUAL
Machine location CASHIER
★
STATION
ORDER TAKER
COUNTER
Backup master
NOT
★
function
EXIST
Select the item to be changed and press the ENTER key.
The setting content is described below.
DISPLAY TEXT
Terminal No.
GLU SYSTEM
GLU system
IRC SET UP
1:
2:
3:
4:
SAVE FILE DELETE
OTHER FILE DELETE
SAVE FILE NON CREATE
OTHER FILE CREATE
SELECT ITEM
MRS
000 ~ 254
000
CENTRALIZED
★
INDIVIDUAL
D-THRU SYSTEM
Drive thru system
CENTRALIZED
★
INDIVIDUAL
MACHINE
LOCATION
Machine location
CASHIER
STATION
★
ORDER TAKER
COUNTER
BACKUP MASTER
When all the machine are set, press the [CA/AT] key.
The [IRC SET UP] screen appears to start the setup.
DISPLAY:
CONTENTS
TERMINAL No.
Backup master
function
★
NOT
EXIST
After setting as above, press the [CA/AT] key to display the [MASTER
LIST] setting screen.
Set the terminal No. and machine No. of all machines (master/satellite/backup master) that are included in the in-line system.
DISPLAY: Setting screen
Enter the terminal No. of inline system and press the ENTER key.
The setting content is described below.
DISPLAY TEXT
TERMINAL No.
CONTENTS
Terminal No.
DISPLAY: Setting screen
SELECT ITEM
MRS
000 ~ 254
000
The setting content is described below.
DISPLAY TEXT
TERMINAL No.
GLU SYSTEM
CONTENTS
Terminal No.
GLU system
D-THRU SYSTEM
Drive thru system
MACHINE LOCATION Machine location
Enter the machine No. of inline system and press the ENTER key.
MACHINE No.
When all the machine are set, press the [CA/AT] key.
The [IRC SET UP] screen appears to start the setup.
DISPLAY:
The setting content is described below.
DISPLAY TEXT
SELECT ITEM
000 ~ 254
CENTRALIZED
INDIVIDUAL
CENTRALIZED
INDIVIDUAL
CASHIER
STATION
ORDER TAKER
COUNTER
CONTENTS
SELECT ITEM
Machine No.
0000000 ~
9999999
MRS
0000000
IRC SET UP
1:
2:
3:
4:
SAVE FILE DELETE
OTHER FILE DELETE
SAVE FILE NON CREATE
OTHER FILE CREATE
When a machine is set, the screen changes to allow the setting of
another machine.
When all the machines are set, press the [CA/AT] key.
The [IRC SET UP] screen appears to start the setup.
[4 STD. WITH IRC]
DISPLAY:
DISPLAY: Setting screen
IRC SET UP
1:
2:
3:
4:
SAVE FILE DELETE
OTHER FILE DELETE
SAVE FILE NON CREATE
OTHER FILE CREATE
[3 BACKUP MASTER]
DISPLAY: Setting screen
Select the item to be changed and press the ENTER key.
The setting content is described below.
[5 STAND ALONE]
Used to restore to a stand alone machine.
Select the item to be changed and press the ENTER key.
MRS
000
★
★
★
CHAPTER 6. SRV MODE PROGRAMMING ("4 DOWN LOAD")
After IRC SETUP, using this setting procedure, download the setting
data from the master.
DISPLAY: SRV mode screen
[2 MACHINE SELECT]
Select the machine among the master list from which you want to
download data.
DISPLAY: MACHINE SELECT screen
Select the "4 DOWN LOAD" and press the ENTER key.
DISPLAY: DOWN LOAD item selection screen
Select the machine and press the ENTER key.
The downloading of data is started.
CHAPTER 7.
SRV MODE PROGRAMMING
("5 DIAGNOSTICS")
Execute the test program.
Fore more information, see the Service Manual.
DISPLAY: SRV mode screen
Select the item and press the ENTER key.
DISPLAY: DOWN LOAD METHOD item selection screen
Select the item and press the ENTER key.
[1 ALL]
Download data from all the machines included in the master list.
COPYRIGHT ã 2000 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted.
In any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.
SHARP CORPORATION
Information Systems Group
Quality & Reliability Control Center
Yamatokoriyama, Nara 639-1186, Japan
2000 May Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement