Marvel MPRO48SS Troubleshooting guide

Marvel MPRO48SS Troubleshooting guide
Marvel Ice Machine
Installation
Operation &
Maintenance
Instructions
Part of AGA Foodservice Group
S TA RT I N G O U T
Remove Packaging
Your ice machine has been packed for shipment
with all parts that could be damaged by movement
securely fastened. Before installing the ice
machine, be sure all packing materials and tape
have been removed.
Important
Save the carton packaging until your ice machine
has been thoroughly inspected and found to be in
good condition. If there is damage, the packaging
will be needed as proof of damage sustained in
transit.
Note to Customer
This ice machine was carefully packed and thoroughly inspected before leaving our plant.
Responsibility for its safe delivery was assumed by
the carrier upon acceptance of the shipment. As
directed on the side of the packaging carton,
claims for loss or damage sustained in transit must
be made on the carrier as follows:
Exterior Damage
Make a thorough damage notation on the delivery
receipt and have the driver acknowledge by signing and dating. Send a written request asking for
an inspection report from the carrier representative
and the date the inspection was requested. Retain
the inspection report and receipt for filing of a
claim.
Concealed Damage
This must be reported to the carrier within fifteen
days. Obtain an inspection report from the carrier.
Retain the inspection report for filing of the claim.
DO NOT RETURN DAMAGED MERCHANDISE
TO THE MANUFACTURER - FILE THE CLAIM
WITH THE CARRIER.
1
I N S TA L L AT I O N
Select Location
The proper location will ensure peak performance of your ice machine. Choose a location
away from heat and out of direct sunlight. Best
performance will be maintained when installed
within the following parameters:
RPE style door
Ideal Ambient Temperature Range*
built-in
55-80°F
freestanding
55-90°F
* Ice Machine will not perform correctly in ambient temperatures less than 55°F.
Cabinet Clearance
Ventilation is required for the bottom front section
of the unit where the grille is located. Keep this
area open and clear of any obstructions.
Adjacent cabinets and countertop can be built
around the unit as long as no top trim or countertop is installed lower than the top of the hinge.
Make certain that the glides supplied with the ice
machine are installed according to instructions.
Make certain your ice machine is level. Leveling
adjustments can be made by raising or lowering
the glides on the bottom of the unit.
Full Wrap
Style Door
Electrical Connection
Check the serial nameplate for the correct power
supply. Use only the electrical power supply
specified on the serial nameplate. Do not use an
extension cord.
Grounding Method
This ice machine is equipped with a power supply
cord with ground. It must be plugged into a mating
grounding type receptacle in accordance with the
National Electrical Code and applicable local
codes and ordinances.
Overlay/Designer
Style Door
Note: The plug shown is
for 115VAC unit. The
prongs on your model
may vary from that
shown if your unit is
other than 115VAC.
THIS UNIT SHOULD NOT, UNDER ANY
CIRCUMSTANCES, BE UNGROUNDED.
2
I N S TA L L AT I O N : D R A I N P L U M B I N G
Drain Plumbing
Your ice machine uses a gravity drain, (figure 1)
that requires 5/8" I.D. tubing from the back of the
ice machine to a plumbed connection to a sanitary
sewer. Remove the access panel to plumb in drain
connection. Gravity drain location for built-in units
can be within the area shown in figure 3. An optional drain pump, (figure 2) can be purchased for your
ice machine if a gravity drain is not accessible.
OBSERVE AND FOLLOW ALL LOCAL CODES
WHEN INSTALLING ICE MACHINE.
figure 1
FAILURE TO USE ADEQUATE DRAINAGE
SYSTEM WILL RESULT IN SURROUNDING
WATER DAMAGE AND/OR POOR ICE
PRODUCTION.
figure 2
figure 3
Gravity Drain Location
* With optional filler kit
3
WAT E R S U P P LY
Water Supply
This ice machine must be connected to a potable,
active cold water supply line delivering water
pressure at a minimum of 20 psi and maximum of
120 psi.
• Water connection is made through a right angle
garden hose fitting. See garden hose fitting for
detailed instruction sheet.
• A water filter is recommended for this unit. A
quality filter can remove particles as well as
remove taste and odors from water. Do not use
any thread sealers.
• Softened water is not recommended. This will
produce mushy, cloudy ice cubes that will stick
together.
• De-ionized water is not recommended. This
water will not form solid ice cubes.
• A water specialist can recommend proper water
treatment.
• After installation of water line, turn on water and
check for any leaks. Additional tightening may be
needed.
• Allow for extra water line for built-in installations
for easy removal of unit and to help prevent the
water line from kinking.
Operation
Your ice machine is unique in forming ice. It uses
fractional freezing to form a slab of ice that is clear
and has less mineral content than the water it is
produced from. This is accomplished by running
water over the cold evaporator plate which gradually freezes the water to produce the ice slab. Mineral deposits are left in the reservoir.
for 45 seconds to drain the reservoir of remaining
deposits. After that, the water valve open will open
for 2 minutes providing 2 quarts of water to the
reservoir for the next ice production cycle.
The ice machine will keep producing ice until the
ice machine's bin is full and will restart automatically when ice needs to be replenished in the bin.
When the ice slab reaches the correct thickness
determined by the temperature of the evaporator
plate, the electronic control switches to the harvest cycle to harvest the ice. During the harvest
cycle, the ice slab falls from the evaporator to the
ice grid cutter. Here, the ice slab is cut into 3/4"
squares by the grid cutter's heated wires. During
the harvest cycle, the drain valve will remain open
4
CARE OF THE UNIT
Care of Unit
1. Avoid leaning on the cabinet door. You may
bend the door hinge or tip the unit.
2. Exercise caution when sweeping, vacuuming,
or mopping near the front of the unit. Damage
to the grille and/or switch can occur.
3. Periodic cleaning of the inside of the ice
machine components and inside of unit (see
Cleaning Your Ice Machine section).
4. Periodic checking and/or cleaning of the front
grille and condenser coils as needed.
Normal Responsibilities of the Owner
• All freight charges
• Damage sustained in transit
• Mileage charge(s) for service calls
• Proper installation including installation of leveling legs.
• Leveling of unit.
• Alterations to original equipment
• Removal or installation of additional equipment
(i.e. drain pump).
• Cleaning and normal maintenance outlined in
this manual.
• Drain and water supply plumbing to the ice
machine.
Help Prevent Tragedies
Each year, children die because they climb inside
a discarded refrigeration product, get trapped
inside and suffocate. Take precautions to prevent
such tragedies by removing the door, taping or
chaining it shut before discarding.
5
CARING FOR YOUR ICE MACHINE
Cleaning Your Ice machine
Some impurities will remain and build-up in the ice
machine and stick to the ice machine's parts over
time. This build-up must be removed for proper ice
production, ice quality, and ice machine life. Your
ice machine is equipped with a cleaning mode that
will help in cleaning out these impurities.
7.
After the cleaning cycle has ended, remove
the front panel again and check that the
build up has been removed. The evaporator
plate should be clean, shiny, and smooth to
the touch. If build up is still visible, repeat
the cleaning cycle above. If build up is
removed, continue below.
The impurities will regularly (at the very least,
annually) need to be cleaned of this build-up,
depending on use and water hardness. You can
use an acid such as one specified for ice machine
cleaning or you can use citric acid to remove the
build-up. To clean the ice machine:
8.
Remove the distributor tube, hose clamp,
hose and its rubber ends.
9.
Thoroughly clean the inside of the distributor tube and the spray holes. You can use
the same cleaning solution as before and an
old toothbrush to reach the inside of the distributor tube.
10.
Reinstall the rubber ends, hose, and hose
clamp to the distributor and then reinstall the
distributor tube to the evaporator with the
spray holes pointed to the bottom of the
evaporator plate. Reinstall the front cover
panel with the two front panel screws.
11.
Clean the ice machine's interior, ice scoop,
interior door panel and door gasket with mild
soap and water. Using two tablespoons of
baking soda in one quart of warm water
while cleaning will help remove odors. Rinse
with fresh water. Do not use any abrasive
cleaning products.
1.
Switch the selector switch to the "OFF"
position.
2.
Remove the drain plug at the bottom of the
reservoir to drain any remaining water and
then reinstall.
3.
Add the recommend cleaner solution to the
reservoir of the ice machine. Access to the
reservoir can be obtained by removing the
front panel screws and the front panel.
Determine to proper amount of cleaner from
the ice machine cleaner manufacturer's mixture ratio based on 3 quarts of water (refer
to manufacturer's directions).
4.
Replace the front cover panel and close the
door.
5.
Switch the selector switch on the grille of the
ice machine the clean position. Three quarts
of water will automatically be added to the
cleaning solution.
Read manufacturer's warnings on ice machine
cleaner products. Personal injury can result.
6.
Your ice machine is now clean and sanitized and
may be put back into operation by switching the
selector witch to the "ON" position.
The total cleaning time will end in 49 minutes. The cleaning cycle will automatically
rinse the evaporator plate and also drain the
cleaning solution and rinse water.
6
T H I N G S TO R E M E M B E R
Things to Remember
• Allow your ice machine to run for 24-48 hours to
accumulate ice in ice machine's bin.
• Keep your ice machine clean for proper ice
quality, production, and unit life.
• Room and water temperatures will greatly
affect the output of ice in your unit (see table).
Ice will also melt away, especially at the start
of an empty bin, but will slow down as ice
accumulates.
7
50
70
70
34
32
80
30
27
90
23
20
WATER TEMPERATURE °F
ROOM TEMPERATURE °F
• Unplug your ice machine before working on
unit.
WATER TEMPERATURE °F
ROOM TEMPERATURE °F
• Your unit will automatically shut down when the
ice bin is full.
APPROXIMATE TIME TO FILL
BIN (HOURS)*
PRODUCTION RATE
(LB/DAY)*
• Unit will cycle often between ice production and
ice harvest cycles.
50
70
70
31
34
80
41
58
90
60
82
*NOTE: DUE TO VARIABLES IN INSTALLATION AND USE, INDIVIDUAL RESULTS MAY VARY.
D O O R A LT E R AT I O N S
Optional Door Handle Installation
(for units without door handle attached)
The door handle for certain doors may be packed
inside your ice machine can be mounted on the
top or side of your refrigerator door. Locate the
handle where it is convenient for you. You will
need a 1/4" hex head driver to install the handle.
Place the handle on the outside surface of the
door. Push gently inward toward the door until the
handle snaps in place. Use the two screws supplied to secure the handle to the door frame by
tightening the screws into the holes on the backside of the handle. Tighten the screws until the tips
of the screws touch the bottom of the backside of
the door frame. Your installation is complete.
Reversing the Door
You may want to change the side on which the
door opens and closes. This can be changed by
the following steps.
1. Remove the door by removing the top hinge
pin and angling the door off of the bottom
hinge pin.
2. Gently pry out the hole plugs on the side
which the hinges will be mounted. A thin
knife will usually allow the hole plug to be
removed just enough to pull the rest of the
way out by hand. Do not destroy these plugs
because they will be used on the other side
of the unit.
3. Remove the hinges from the unit.
4. Remove the hinge pin from the bottom hinge
that was removed. Install this pin on the
other hinge that was also removed.
5. Install the hinges on the desired side of the
unit.
6. Install the door by inserting the bottom door
bushing with the bottom hinge pin and
angling door in until top door bushing and
hinge line up. Install the upper hinge pin.
7. Install the hole plugs from step 2 in holes.
8
O B TA I N I N G S E RV I C E
Before Calling for Service
Before calling for service, check the following
items:
• Make sure unit is plugged into outlet.
• Check the outlet for power. Test outlet with
lamp to make certain outlet has power.
• Make sure ice machine's switch is in the "ON"
position.
• Make sure that there is cold water supplied to
the ice machine.
• Make sure drain plug on bottom of reservoir
is inserted.
• Make certain unit is level from front to back
and side to side.
• Make certain that the drain line to the ice
machine is unrestricted or kinked.
• Use troubleshooting guide, pages 11-14 for
other diagnosis.
If you are not able to correct the problem, contact
your dealer or the manufacturer. Be sure to have
the model number and the serial number handy
before you call. The model and the serial number
are located on the lower front part of the ice
machine's cabinet.
How to Obtain Service
Your ice machine requires little service because
the best and most up-to-date materials, equipment and quality control methods are employed
throughout the manufacturing process.
2. If you are in an area where there is no service representative, write or call the manufacturer directly. We will make recommendations as to the proper procedure for correction. Service work and replacement parts, if
required, will be provided as covered by your
limited warranty.
3. In all correspondence regarding service, be
sure to give the model number, serial number and proof of purchase.
4. Try to have information or description of the
nature of the problem, how long the unit has
been running, the room temperature, water
temperatures, and any additional information that may be helpful in quickly solving the
problem.
SEND IN YOUR WARRANTY RECORD
CARD IMMEDIATELY AFTER TAKING
DELIVERY OF YOUR ICE MACHINE.
Every new ice machine that leaves the factory
contains this Owner's Guide. Keep this Owner's
Guide in a safe place for convenient reference.
For Your Records
Date of Purchase
Dealer’s Name
Dealer’s Address
If trouble occurs during normal operation, read
"Things to remember" section first and, if necessary, check the troubleshooting guide. If service
becomes necessary:
1. Contact the dealer where your appliance
was purchased or the manufacturer for the
name of the nearest authorized service representative. The service representative will
have full authority to make any repairs
deemed necessary.
9
Dealer’s city
Appliance Serial Number
Model Number
Date Warranty Card Mailed (within 10 days of purchase)
Dealer’s State
Zip
WA R R A N T Y
Entire Product
Limited One Year Parts and Labor Warranty
Marvel warrants that it will supply all necessary
parts and labor to repair or replace in the end
user's home or office, any component which
proves to be defective in material or workmanship,
subject to the condition and exclusions stated
below, for a period of one year from the date of
purchase by the end user.
Additional Second Through Fifth Year
Limited Parts Only Warranty
During the four years following expiration of the
one year limited warranty, Marvel will supply
replacement parts for the hermetically sealed
refrigeration system which consists of the compressor, condenser, drier, accumulator, by-pass
valve, connecting tubing and the evaporator that
are proven to be defective due to workmanship or
materials subject to the conditions and exclusions
below.
The above warranties do not cover:
• Shipping costs of replacement parts or returned
defective parts.
• Customer education or instructions on how to
use the appliance.
Parts or Service
Not Supplied or Designated by Marvel
The above warranties also do not apply if:
The original bill of sale, deliver date or serial number cannot be verified.
Defective parts are not returned for inspection if so
requested by Marvel.
The refrigeration equipment is not in the possession of the original end use purchaser.
The warranties set forth herein are the only warranties extended by Marvel Industries. Any implied
warranties, including the implied warranty of merchantability, are limited to the duration of these
express warranties. In no event shall Marvel
Industries be liable for any consequential or incidental damages or expenses resulting from
breach of these or any other warranties, whether
express or implied.
Some states do not allow the exclusion or limitation of consequential damages or a limitation on
how long an implied warranty lasts, so the above
exclusion or limitation may not apply to you. This
warranty gives you specific legal rights and you
may have other rights that may vary from state to
state.
• Any content loss due to product failure.
• Removal or installation.
Nor do the above warranties cover failure of this
product or its components due to:
1.Transportation or subsequent damages.
2.Use commercially or use other than normal
household or small office.
3.Improper installation, misuse, abuse, accident
or alteration, use on wiring not conforming to
electrical codes, low or high voltages, failure to
provide necessary maintenance, or other unreasonable use.
No person, firm, or corporation is authorized to
make any other warranty or assume any other
obligation for Marvel Industries. These warranties
apply only to products used in any of the fifty
states of the United States and the District of
Columbia.
To obtain performance of this warranty, report any
defects to:
Marvel Industries
P.O. Box 997
Richmond, Indiana 47375-0997
Phone: 765-962-2521
10
TROUBLESHOOTING ONE
PROBLEM
POSSIBLE CAUSE
CORRECTION
Unit does not operate.
The unit is unplugged.
Breaker is tripped or fuse is blown.
Plug in the unit.
Reset breaker or replace fuse. Check to make sure there is
not a short in the electrical circuit.
Set the rocker switch on the grille of the ice machine to the
"ON" position.
Ice machine selector switch is in the "OFF"
position.
Unit operates but does not produce
any ice.
The unit has just been started and it has
been less than 6 hours.
Typical ice production cycle can take up to
1.5 hours. Initial startup cycles can be
longer.
The selector switch is in the "OFF" or
"CLEAN" position.
No water in the reservoir.
Distributor tube is restricted.
Build up of deposits on evaporator plate.
Condenser fan air flow is restricted.
Room and/or water temperature is too
warm.
Leaking drain valve.
Inadequate drain system.
Grid cutter is unplugged.
11
Ice produced when the unit is initially started will melt off in
the bin. Ice will accumulate in the bin. In 6 hours there can
be a few cubes in the bin. This is normal operation.
Check the unit in 24 hours for ice accumulation in the bin.
Set the rocker switch on the grille of the ice machine to the
"ON" position.
Make sure that the reservoir drain plug is installed. Check
the water line to the unit to make sure it is on and that there
are no restrictions or kinks in the line. Check all filters to
make sure they are not restricted or plugged.
See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation.
See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation.
Make certain the grille in the front of the unit is free and
open for proper air circulation. Check and clean the condenser coil by removing the grille in the front of the unit.
Clean the condenser with a vacuum and brush attachment.
Move the unit to an area where ambient temperature is
below 90 deg. F. The unit should not be placed next to a
heat source such as an oven. Check for cold water connection.
See "CLEANING YOUR ICE MACHINE" section for cleaning the unit. This will also dissolve and flush out foreign
material in the drain valve causing it to leak.
Restriction in drain lines will cause ice in the bin to melt. If
using a gravity drain, make certain there are no kinks or
restrictions in the drain lines. If using a drain pump, check
the inlet screen, discharge line, and vent line for any build
or restrictions.
Plug in the grid cutter so that ice slabs can be cut into cube.
TROUBLESHOOTING TWO
PROBLEM
POSSIBLE CAUSE
CORRECTION
Ice cubes are too small (less than
1/2 inch thick).
Low ice consumption.
Ice is slowly melting in the ice bin and will affect the size of
the ice cube. This is normal operation. When the ice bin
needs to be replenished, cubes will return to regular size.
Make sure that the reservoir drain plug is installed properly.
Check the water line to the unit to make sure there are no
restrictions or kinks in the line. Check all filters to make
sure they are not restricted or plugged.
See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation.
See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation and cube size.
Restriction in drain lines will cause ice in the bin to melt to a
thinner cube. If using a gravity drain, make certain there are
no kinks or restrictions in the drain lines. If using a drain
pump, check the inlet screen, discharge line, and vent line
for any build or restrictions.
See "CLEANING YOUR ICE MACHINE" section for cleaning the unit. This will also dissolve and flush out foreign
material in the drain valve causing it to leak.
Move to an area where temperature is below 90 deg. F.
Not enough water in reservoir.
Distributor tube is restricted.
Build up of deposits on evaporator plate.
Inadequate drain system.
Leaking drain valve.
Room temperature is too warm.
Ice cubes are too big (greater than
3/4 inch thick).
Ice slab not releasing.
Condenser fan air flow is restricted.
Room temperature is too warm.
Hollow ice slab.
Distributor tube is restricted.
Build up of deposits on evaporator plate.
Low water level in reservoir.
See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation and cube size.
Make certain the grille in the front of the unit is free and
open for proper air circulation. Check and clean the condenser coil by removing the grille in the front of the unit.
Clean the condenser with a vacuum and brush attachment.
Move to an area where temperature is below 90 deg. F.
See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation.
See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation and cube size.
Make sure that the reservoir drain plug is installed properly.
Check the water line to the unit to make sure there are no
restrictions or kinks in the line. Check all filters to make
sure they are not restricted or plugged.
12
TROUBLESHOOTING THREE
PROBLEM
POSSIBLE CAUSE
CORRECTION
Ice is not clear.
Low water level in reservoir.
Make sure that the reservoir drain plug is installed properly.
Check the water line to the unit to make sure there are no
restrictions or kinks in the line. Check all filters to make
sure they are not restricted or plugged.
Make certain that water line is not connected to the water
softener.
Move the unit to an area where room temperature is above
55 deg. F.
Softened water supply.
Room temperature is too cold.
Low ice production. Unit is running,
has run over a 48 hour period, and
there is little ice in bin.
Low water level in reservoir.
Distributor tube is restricted.
Build up of deposits on evaporator plate.
Inadequate drain system.
Condenser fan air flow is restricted.
Unit continues to run and produce
ice.
Ice bin is not full.
Ice bin is full.
Room temperature is too warm.
ice machine is not level.
Grid-cutter is not cutting the ice
slab.
13
The selector switch is not in the "ON" position
The grid cutter is not plugged into the
receptacle.
Time to cut through the slab
Make sure that the reservoir drain plug is installed properly.
Check the water line to the unit to make sure there are no
restrictions or kinks in the line. Check all filters to make
sure they are not restricted or plugged.
See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation.
See "CLEANING YOUR ICE MACHINE" section for cleaning the unit for proper operation.
Restriction in drain lines will cause ice in the bin to melt. If
using a gravity drain, make certain there are no kinks or
restrictions in the drain lines. If using a drain pump, check
the inlet screen, discharge line, and vent line for any build
or restrictions.
Make certain the grille in the front of the unit is free and
open for proper air circulation. Check and clean the condenser coil by removing the grille in the front of the unit.
Clean the condenser with a vacuum and brush attachment.
The unit will automatically shut down when ice reaches the
sensing tube.
The unit will automatically shut down when ice reaches the
sensing tube and has completed the harvest of the ice slab.
Move the unit to an area where room temperature is below
90 deg. F.
Use a level to check the unit for level from side to side and
front to rear.
Set the rocker switch on the grille of the ice machine to the
"ON" position.
Remove the escutcheon panel and plug the grid-cutter into
the receptacle on the side of the line.
It can take up to 35 minutes to cut through a harvested ice
slab. This is normal operation.
TROUBLESHOOTING FOUR
PROBLEM
POSSIBLE CAUSE
CORRECTION
Ice cubes are sticking together.
Ice consumption is low.
Use the ice in the bin frequently. Ice will stick together if left
in insulated bin over long periods of time.
Move the unit to an area where temperature is below 90
deg. F.
Room temperature is too warm.
Ice level is too high.
The ice machine is not level.
Room temperature is too warm.
Ice deflector is not in place or secured
properly.
Bin level sensing tube needs adjusted.
Ice level is too low.
The ice machine is not level.
Room temperature is too cold.
The selector switch is not in the "ON" position
Water keeps backing up into the ice
bin (gravity drain).
Inadequate drain system.
Foreign material in ice bin drain.
Water keeps backing up into the ice
bin (drain pump).
Drain pump tubing kinked or restricted.
Inlet screen to the drain pump is restricted
or blocked.
Drain pump and/or the ice machine are not
level.
The drain pump cycles on and off
erratically.
Vent line to the drain pump is restricted or
kinked.
Discharge line is restricted or kinked.
The drain pump is not level.
Use a level to check the unit for level from side to side and
front to rear.
Move the unit to an area where temperature is below 90
deg. F.
Check to see that the ice deflector is in place and secured
below the grid-cutter.
You can adjust the bin level sensing tube by simply pressing directly down on the tube 5 inches from the front of the
tube to get a desired bin level.
Use a level to check the unit for level from side to side and
front to rear.
Move the unit to an area where temperature is above 55
deg. F.
Set the rocker switch on the grille of the ice machine to the
"ON" position.
Restriction or improperly installed drain lines will cause
water to back up into the ice bin. Make certain there are no
kinks or restrictions in the drain lines. If necessary, consult
a qualified plumber.
Foreign material is restricting or blocking the ice bin drain
located at the right rear corner of the ice bin. The drain will
need to be cleared.
Check inlet, discharge, and vent line tubing for any kinks or
restrictions and repair as necessary.
Clean the inlet screen to the drain pump.
Check and level if necessary the drain pump as well as the
ice machine.
Check the vent line for any restrictions or kinks and repair
as necessary.
Check the discharge line and connection to the desired
drain for any restrictions or kinks and repair as necessary.
The drain pump must be level. Check for level on the top of
the drain pump case and adjust the tubing or use shims to
level.
14
S E RV I C E PA RT S D I A G R A M O N E
15
S E RV I C E PA RT S L I S T O N E
Illus. No.
1
2
3
4
5A
5B
6
7A
7B
8
9
Description
Cabinet Assembly
Hole Plug
Screw
Escutcheon
Plastic Grille (White)
Plastic Grille (Black)
On-Off-Clean Switch
Screw (White Plastic Grille)
Screw (Black Plastic Grille)
Stainless tin panel (Optional)
Screw (Optional)
Qty. Req.
Part No.
Service Assembly
1
6
2
1
1
1
1
1
1
1
2
Various
41001929
41004079
41005700
41006376
41006274
41005824
41005486
08205072
42284093
08204920
Various
Various
42242989
42242989
42243390
42243391
42242992
42243390
42243391
42244709
42244709
16
S E RV I C E PA RT S D I A G R A M T W O
17
S E RV I C E PA RT S L I S T T W O
Illus. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Description
Distributor Tube End
Distributor Tube
Tubing
Evaporator Assembly
Screw
Clamp
Hose Clamp
Washer
Screw
Circulation Pump
Reservoir
Spacer
Screw
Clamp
Sleeve w/ thermistor
Screw
Screw
Drain Plug
Grid-Cutter Assembly
Deflector
Screw
Wellnut
Screw
Thermistor
Retainer Clip
Screw
Ice Scoop
Qty. Req.
Part No.
2
1
1
1
4
1
1
2
2
1
1
2
2
1
1
2
4
1
1
1
4
20
1
1
1
2
1
41005705
41005515
41005042
42052559
08204920
41006002
41006126
08205068
08204920
41005537
41005345
41004366
41005773
1150003A
42154607
08204920
08204920
41005859
42412615
41006040
08204920
41005503
41004079
41006205
41006042
08204920
41005536
Service Assembly
42242977
42242976
42242976
42242978
42242978
42242978
42242976
42242981
42242980
42242980
42242981
42242981
42242981
42242986
42242986
42242986
42242984
42242982
42242984
42242985
42242985
42242987
42243392
42243392
42242975
42242975
42242993
18
S E RV I C E PA RT S D I A G R A M T H R E E
19
S E RV I C E PA RT S L I S T T H R E E
Illus. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
27
28
29
30
31
32
33
34
35
36
37
38
39
40
40
41
42
43
44
45
46
46
47
Description
Qty. Req.
Condenser
1
Pop Rivet, Steel
4
Coil Retainer
1
Solenoid Coil
1
Hot Gas Valve
1
Drier Assembly
1
Speed Nut
1
Fan Shroud
1
Fan Blade
1
Silencer, Spacer
1
Locknut
5
Fan Motor Assembly
1
Carriage Bolt
5
Carriage Bolt
2
Carriage Bolt
1
Sleeve, Compressor
2
Grommet, Compressor
4
Locknut
1
Lock Washer
1
Ground Wire, Compressor
1
Lock Washer
1
Screw
1
Washer
2
Locknut
2
Compressor Assembly
1
Compressor PTC Starter
1
Back Panel
1
Back Panel-Stainless Steel
1
Power Cord Clamp
1
Locknut
1
Carriage Bolt
1
Baseplate
1
Water Valve Assembly
1
Drain Valve
1
Screw
2
Screw
2
Tee Fitting
1
Hose Clamp
4
Power Cord
1
Bracket
1
Screw
24
Screw-Stainless Steel
24
Electronic control
1
Transformer
1
Screw
6
Terminal Block
1
U-Clip
1
Access panel assembly
1
Access panel assembly-Stainless Steel 1
Compressor Overload
1
Part No.
41003609
41003962
41003662
41003601
41003914
42102389
41000153
41006282
41003616
M000101A
41006874
42183571
1130006A
08205114
1130006A
41008199
41008198
41006874
41005417
41001401
08205116
08205200
08204877
08205051
41008182
41008200
41009202
41009203
41006046
41006874
1130006A
41006276
42262644
41005530
08204928
08204928
41005702
41006769
41006733
41005868
08204928
41005076
41006035
41005681
41005086
41005078
41005945
41005943
41008533
41008201
Service Assembly
42243035
42243035
42242020
42242020
42242020
42242961
42244701
42244704
42244701
42244701
42244701
42244701
42244701
42243194
42242900
42243194
42243194
42242900
42242900
42242900
42242900
42242900
42243194
42243194
42243194
42244702
42242962
42245300
42242963
42242963
42242963
42242964
42242965
42242966
42242965
42242966
42242967
42242967
42242963
42242968
42242962
42245300
42243384
42242973
42242971
42242971
42243015
42243016
42245301
42244703
20
S E RV I C E PA RT S D I A G R A M F O U R
21
S E RV I C E PA RT S L I S T F O U R
Illus. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Description
Hinge Pin
Screw
Hinge
Handle
Screw
Door Gasket
Hinge
RPE Cap Assembly
Screw
Door, Complete Assembly, 30IM
Hinge Bushing
Door Nameplate
Hinge Adapter Screw
Hinge Adapter
Qty. Req.
Part No.
Service Assembly
2
6
1
1
2
1
1
1
2
1
4
1
4
2
41004106
Various
Various
Optional
Optional
41006285
Various
Optional
Optional
Various
41000255
Various
Optional
Optional
2240013A
Various
Various
Optional
Optional
42243388
Various
Optional
Optional
Various
2240013A
Various
Optional
Optional
22
WWW.MARVELINDUSTRIES.COM
Phone: (765) 962-2521
I
N
Fax: (765) 962-2493
MARVEL
D U S T R I E
Part of AGA Foodservice Group
233 Industrial Parkway
P.O. Box 997
Richmond, IN 47375-0997
41006412 Rev. G
S
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement