Upcom | Y | User guide | upcom Y User guide

User Guide
Ku Band
Solid State Amplifiers – SSPA
Redundant Configuration
Outdoor Band Solid State
Amplifier System – Redundant Configuration
User Guide
This section provides general information for the UPCOM TECHNOLOGIES line of Outdoor
Solid State Amplifers – SSPAs with Built-In Redundancy Configuration Option. The
Outdoor SSPA has been designed and manufactured to be extremely robust and reliable. It is
well suited for harsh outdoor environments.
Please refer to Appendix A for the appropriate product data sheet and specifications.
The Outdoor SSPA Redundancy Ready is a one-piece integrated amplifier system. It includes
the AC / DC Power Supply, microwave Booster Amplifier Module, microcontroller based
monitor and control circuitry, and an efficient thermal management system.
The reduced size and weight of this system allow it to be used in a wide variety of installations;
many of which historically precluded the use of solid state units. This system is ideal for
mounting on the boom of small antennas or anywhere that size and weight are a major
Features include:
 Compact size
 Light weight
 Auto-Sensing Power Supply
 Output Power Detection
 Internal 1:1 Redundant Capability – Built in Controller
 Serial (RS-232 / RS-485) Control Circuitry
 Windows Monitor & Control Software
 Optional gain control (on selected configurations)
Equipment Supplied
The following equipment is supplied with each unit:
 The Outdoor SSPA Assembly
 Prime Power Mating Connector
 M & C Mating Connector
 “Y” Cable between SSPAs and WG Switch
 CD with UPCOM TECHNOLOGIES Monitor & Control Software (where applicable)
 Low Power Driver BUC (where applicable)
 WR75 Waveguide adapter BUC-SSPA (where applicable)
General Information
Safety Considerations
Potential safety hazards exist unless proper precautions are observed when working with this
unit. To ensure safe operation, the user must follow the information, cautions, and warnings
provided in this manual as well as the warning labels placed on the unit itself.
High Voltage Hazards
Only qualified service personnel should service the internal electronic circuitry of the Outdoor
SSPA. High DC voltages (400 VDC) are present in the power supply section of the amplifier.
Care must be taken when working with devices that operate at this high voltage levels. It is
recommended to never work on the unit or supply prime AC power to the unit while the cover
is removed.
RF Transmission Hazards
RF transmissions at high power levels may cause eyesight damage and skin burns. Prolonged
exposure to high levels of RF energy has been linked to a variety of health issues. Please use
the following precautions with high levels of RF power.
 Always terminate the RF input and output connector prior to applying prime AC input
 Never look directly into the RF output waveguide.
 Maintain a suitable distance from the source of the transmission such that the power
density is below recommended guidelines in ANSI/IEEE C95.1. The power density
specified in ANSI/IEEE C95.1-1992 is 10 mW/cm². These requirements adhere to
OSHA Standard 1910.97.
 When a safe distance is not practical, RF shielding should be used to achieve the
recommended power density levels.
When the unit is received, an initial inspection should be completed. First ensure that the
shipping container is not damaged. If it is, have a representative from the shipping company
present when the container is opened. Perform a visual inspection of the Outdoor Amplifier to
make sure that all items on the packing list are enclosed. If any damage has occurred or if
items are missing, contact: UPCOM TECHNOLOGIES Inc.
Return of Equipment
When returning items back to UPCOM TECHNOLOGIES for replacement or repair, please
prepare the following information:
 A written description of the problem encountered.
 The part number and serial number of the unit in question.
Once this information is ready, contact UPCOM TECHNOLOGIES for a Return Material
Authorization (RMA) number and shipping instructions.
Ports and Interfaces
Prime Power Connection
The Prime Power Connector is the point where the unit receives input power. A connector
3100A 14S-7P is used.
The AC input can operate over a range of 90 - 270 VAC, at 47 - 63 Hz. This connector is a 3
(three) pin circular connector and the mating connector is supplied with the unit
AC Input Connector Pin out:
Pin A
Pin B
Pin C
90-260 VAC, 47-63Hz
Units with higher output power levels (> 50 W for Ku Band and > 100 W for C Band)
should be powered only from a 180 - 270 VAC source. This will keep AC line currents to a
safe operating level and minimizes cable losses.
In some cases, the unit may only be specified to operate at higher input voltage levels – please
check the labels or accompanying Test Record for this information.
When wiring up the mating connector, carefully follow the pin descriptions noted in the
accompanying Test Record. Incorrect connections can seriously damage the unit. It is
highly advisable that the installer checks all the pins at the AC connectors for
resistance to the chassis ground to make sure that the live and ground pins are
correctly identified .
Please contact the factory if there are any questions regarding these input connections.
RF Input
The RF Input is a type WR75 Flange Grooved . Make sure that a properly sized gasket is used
at the flange, with silicone paste. The input frequency is in the KU Band. Nominal RF input
levels are approximately + 20 dBm depending on the output power level and the system gain
of the unit.
The maximum input level should be limited to +33 dBm to avoid damaging the unit.
RF Output
The RF Output is brought out through waveguide in the Outdoor SSPAs. The Ku Band SSPAs
have a WR-75 Grooved Flange while the C Band SSPAs have CPR style grooved flange
(CPR-137G). An isolator is provided at the output flange with a termination capable of handling
full reflected output power.
Caution should be observed here to make sure that the antenna or a suitable termination
(dummy load) is connected to this port before operating the SSPA The SSPA is protected
against reflection but dangerous levels of microwave energy can be present at this port.
Never look directly into the RF output waveguide.
M & C Connector
The Monitor and Control (M & C) connector is the primary interface point for controlling the
SSPA and monitoring fault conditions. A 10 pin PT02 E12-10P Connector is used at the unit.
A Redundant configured unit may be operated in stand-alone mode, and behaves in a similar
way to a normal Microcontroller equipped unit. If this is done, it is important to cover the
Redundancy Port to protect it from the external environment, since there are live voltages
present on this interface. Never connect anything except for the supplied cables to this
interface port.
Pin Out for M&C Connector
RS 485
RS 232
The air intake and exhaust are both located on the bottom side of the SSPA. The intake is
brought through one or two fans ( two fans on 50 watts units KU Band and higher and one fan
on lower power units) while the exhaust is along the rows of heat-sink fins.
A minimum clearance of 12 inches (305 mm) should be maintained between the air intake of
the Outdoor SSPA and exhaust during operation. This will ensure that there is no forced recirculation of airflow from exhaust to intake.
Some lower output power units are not equipped with a fan, but the same clearance stated
above must be kept around the unit for proper operation.
Monitors and Controls
Monitor signals and Control lines are present on the M & C Connector when this option is
installed. Typically, single threaded units are NOT equipped with micro-controller by default.
With a Microcontroller equipped system, all Monitors and Controls can also be accessed
remotely by RS-232 / RS-485.to a Windows based PC; and other Alarms become available as
well. Units equipped with a Redundancy option have a Microcontroller M & C installed by
Redundancy Controller is a built in module to the units . The redundancy ready units have a
connector “ SWITCH” which is connected to the waveguide switch via a “Y” cable supplied
with the units.
The full M & C Connector pinout is listed here for convenience. However, always check the
Test Bench Record supplied with the unit to view which interfaces have been installed on your
unit, or to see if it has had any custom modifications.
Pin #
3 pin male
“M&C Interface”
10 pin male
10 pin male
RF Input
RF Output
Line (AC)
Neutral (AC)
Rx+ In
Rx- In
Tx+ Out
Tx- Out
Alarm Out
Mute In
Rx In
Tx Out
33 dBm, max
RS232 COM port setting: 9600 bps, 8 bit, 1 stop bit
47.0 dBm max
Low when alarm
Muted when Low
Temperature Monitor
The temperature of the unit baseplate is monitored by a voltage analogous to temperature.
The output is 3.0 V at 27 ºC with a slope of 10 mV / ºC.
RF Output Power Monitor
The output power of the unit is monitored by a voltage analogous to the output power level.
The voltage is restricted to in between 0 V to 5 V. This detected voltage is useful over a 20 dB
range of output power.
Ground (GND)
This pin is connected to the chassis, which also represents the main Ground of the unit.
RS-232 / RS-485
Available with optional Microcontroller equipped systems. This serial link is normally used to
communicate with a remote PC running UPCOM TECHNOLOGIES Monitor and Control
Software. This enables a simple way to view / control the Monitors and Controls listed above,
and also enables the functions listed below.
Normally, either RS-232 or RS-485 is available at any one time (both interfaces cannot be
used simultaneously). Communication links using RS-232 are typically good up to 30 ft. (9 m)
in length. Installations exceeding this length should use the RS-485, which will allow serial
control up to 4000 ft. (1200 m).
Monitor and Control Software
UPCOM TECHNOLOGIES Monitor and Control Software is provided on CD for units equipped
with an onboard Microcontroller system. A Windows based PC uses this software to remotely
monitor and control the SSPA through its serial port.
Various Monitors and Alarms are displayed along the left hand side of the interface. If a
problem has been detected, it will be displayed in red, and the SSPA will be placed into a
muted state.
Installation Instructions
System Requirements:
 PC running Windows 98, Me, 2000, or XP (NT 4.0 with Service Pack 6a)
 Display resolution of 800 x 600 or greater
 Free serial port (RS-232 or RS-485)
Compatibility under Windows Vista has not been tested.
Status Display (Optional )
This indicator shows the general status of the Outdoor SSPA – if everything is good, or if an
error condition has occurred, or if the unit has been manually disabled by mute control. Also,
the operating status of a Master/Slave redundant pair is reflected.
Booster Temperature Display (Optional )
Using the UPCOM TECHNOLOGIES Monitor and Control Software, a thermometer display
with a numeric readout of the baseplate temperature of the unit in degrees Celsius is shown.
The baseplate temperature typically experiences a 20 to 30 degree rise above ambient on the
highest power Outdoor SSPAs and 15 to 20 degree rise on lower power units. This display
corresponds with the Temperature Monitor outlined in the analog M&C section above.
Output Power Display (Optional )
A numeric readout of the output power level is displayed in units of dBm. The indicator is
calibrated at the factory using the middle frequency of the SSPA, and has approximately a 20
dB dynamic range. When this range is exceeded, the readout shows “Low” or “High”
depending on which particular limit has been reached.
Overheated Alarm (Optional )
This alarm indicates when the unit’s baseplate rises above about 85 ºC, which is an
overheated condition. The unit will automatically enter into a muted state. This function has
approximately a 20 ºC hysteresis window which will allow the SSPA to re-enable itself when
the temperature is reduced by 20 ºC at the baseplate.
PS Voltages Monitor (Optional )
The output voltage levels of the Power Supply are monitored and this alarm indicates when
any of them fall below a preset level. Three voltages are monitored: +12 V feeding the
Booster Amplifier and –5 V from the bias assemblies attached to the Booster Amplifier. The
unit will enter a muted state when this alarm is active.
Manual Control Enable/Disable and Mute Input (Optional )
A manual mute control can be accessed from the Enable/Disable button of the software. For
systems set up for 1:1 Redundant operation, this control is also used for manually selecting the
Active unit in a redundant pair.
Mate Status (Optional )
In redundant configurations, the Mate Status indicates the mute condition of its mate. That is,
the Master display shows the Slave condition, and the Slave display shows the Master
Attenuator Control (Optional )
System conversion gain can be changed here provided an attenuator module has been
installed. The range of control is from 0 dB (no attenuation applied) to 20 dB (20 dB of gain
reduction) in 0.5 dB steps. The value may be stepped up or down, or entered directly with the
keyboard by highlighting the entry field. Note that this control is dependent on an installed
hardware option. If it is not installed, this control will not have any effect.
Temperature Compensation
Tighter temperature compensation response is also possible with the attenuator module
installed. There is no user control here, and the unit must have the requisite hardware option
installed, and be calibrated at the factory for this function to be active.
Communication Status (Optional )
The communication status between the software and the SSPA is reflected here. If there is a
problem here, double-check all serial port connections and ensure the correct Com port is
selected (the software uses the Select Port menu item).
Menu Items (Optional )
Under the File menu item, there is a set of calibration routines exposed to the user. These are
intended for factory use only. No support will be provided if any of these settings are adjusted.
Under the Select Port menu item, your appropriate Com port is selected for serial
communication to the SSPA.
Redundancy Interconnection Diagram
10pin connector
6pin connector
10pin connector
Quick Start Guide
 Check the connectivity of the AC Pins and also at the AC Cable to make sure that
Line or Neutral pins are NOT connected to the ground
 Connect the low power KU Band output from a low power BUC or indoor upconverter to
the labeled port. Nominal input levels are approximately +20 dBm depending on the
output power level of the unit.
 Connect the rigid waveguides to the SSPA’s RF outputs and to the waveguide switch as
indicated in the Redundancy Diagram
 Connect to the “Y” Cable supplied with the units to the “Switch “ Ports at the units and to
the control port of the waveguide switch.
 The SSPA’s output is taken from the waveguide port (RF Out). Caution should be
observed here to make sure that the antenna or a suitable termination is connected to
this port before operating the SSPA.
 Ensure there is proper clearance around the unit.
 Connect the chassis ground (GND) to a proper ground connection
 Connect AC Input power to the connector. The unit will be enabled almost immediately,
provided it is not forced into a mute state.
 Connect the M & C interface to an available COM port on your computer and/or to your
analog based monitoring and control equipment.
 Run the UPCOM TECHNOLOGIES Monitor and Control Program.
 Recommendation: if possible install the SSPA with the fans facing down in order
to avoid accumulation of debris inside the fans that may block the fans.
General Maintenance
With proper care and maintenance, your SSPA will provide many years of reliable service.
Please follow these maintenance guidelines so that your equipment will provide you with the
maximum amount of trouble-free service.
Basic Cleanliness
The exterior chassis of the SSPA acts as a large heatsink that must dissipate at least a few
hundred Watts. Excessive dirt, dust, debris, and sand accumulated on the chassis surface will
impede its ability to dissipate heat, and will result in higher internal temperatures, potentially
shortening the SSPA lifespan.
Periodically inspect the chassis for excessive dirt, and remove as necessary. A brush
combined with compressed air is the safest way to clean the unit. Also, inspect the fan
assembly for any dirt or debris that also might impede airflow.
Internal Fuse
The internal power supply is protected by a fuse to prevent excessive input current
consumption. Contact the factory if you suspect the internal fuse has tripped, and instructions
will be sent on how it can be replaced.
Fan Replacement
Normally the fan on the unit operates continuously when input power is connected to the unit.
If the fan stops turning, and the SSPA still provides an output signal when it is cool, it is time to
replace the fan. Immediately remove power to the unit the prevent damage by overheating.
Contact the factory to order the correct replacement fan for your particular model.
The fan is encased in a shroud to direct airflow to the chassis heatsink fins. First remove the
shroud from the main chassis using the screws at each side of the chassis. The fan and
shroud assembly will be connected by wires to the main chassis. Disconnect the wire
connection by pulling apart the inline (wire to wire) connector.
Next, remove the screws holding the fan to the shroud and fan grille. Remove the fan, and
install the replacement fan in reverse order as described above.
Theory of Operation
AC / DC Converter
The prime AC input power is delivered to a converter module that produces 300 VDC. This
module is an auto-sensing front end that has proven reliability and allows the amplifier system
to operate over a wide variety of input power conditions encountered around the world.
DC / DC Converter
The DC/DC converter module is a switched mode power supply that converts the 300 VDC to
12 VDC. This 12 VDC is the primary high current, DC voltage source that operates the booster
amplifier module.
A secondary module converts the 300 VDC to 24 VDC.
Units with input AC power use the above AC / DC and DC / DC topology.
Cooling System
The Outdoor SSPA’s cooling system represents a landmark in microwave telecommunication
amplifiers. It is a unique system of heat sinks that have been computer optimized to provide
extremely efficient cooling of all of the system’s functional blocks. This high efficiency cooling
system is primarily responsible for the small overall package size and reduced weight of the
The Cooling System is based on a forced convection technique in which both system fans
provide the air intake while the exhaust is brought out around the outer perimeter of the fans.
The fan is up to 300 CFM rated and operate into approximately 0.3 in. H20 back pressure. It is
also weather protected for reliability under a variety of conditions.
This module uses GaAs MESFET technology to boost the signal level to its final output power
level. A bias assembly connects the +12 V power supply with the FETs, and provides proper
bias voltages (including the negative voltage for the FET gates), and voltage sequencing at
turn on and turn off. The gain for this section is in the neighborhood of 25 dB.
Microcontroller ( Optional )
This section is responsible for serial communications and for processing of the Monitors and
Controls. Various alarms are monitored, such as overheating, along with select DC voltages.
The microcontroller disables the SSPA when any of these status indicators show a problem.
In addition, it is possible for the microcontroller to report output power levels in dBm and
control system conversion gain (when appropriate hardware is installed).
In Redundant configured units, the Microcontroller is also responsible for system switching
Attenuator Module
This is an electrically controlled variable attenuator – an optional component that generally
receives control signals from the Microcontroller. It is responsible for both gain control
functions and supplemental gain versus temperature compensation.
Appendix A
Operating Frequency Range
Output Power 1dB Comp
Input Power @ P1dB output
Input Power range without damage
Input Return Loss
13.75 - 14.5 GHz
47 dBm
20 dBm nominal
0 - 33 dBm
> -16 dB
Gain flatness
Gain flatness 40MHz
Gain Variation Over Temperature
Spurious @ P1dB
IMD (With 2 carriers @6dB backoff 1dB Comp)
25 dB min
 2.0 max
-15 dB
0.3 dB
 3 dB max
-55dBc max
-27dBc max
Power supply
AC 90-260V ±20%, 50/60Hz
Operating Temperature
Relative Humidity
Weight ( 50 watts KU)
Dimensions ( 50 watts KU)
-30 °C to 55 °C
up to 98%
14 kg
Phase Noise
< -30 dBc/Hz at 10 Hz
< -60 dBc/Hz at 100 Hz
< -70 dBc/Hz at 1 kHz
< -80 dBc/Hz at 10 kHz
< -90 dBc/Hz > 100 kHz
Appendix B
Download PDF