Vintage | 551170 | Specifications | Vintage 551170 Specifications

1969-70 MUSTANG
w/o FACTORY AIR GEN IV
551170
18865 GOLL ST. - SAN ANTONIO, TX. - 78266 ph.210-654-7171 - fax 210-654-3113
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 1 OF 26
1969-70 MUSTANG w/o AC GEN IV
Table of Contents
PAGES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
COVER
TABLE OF CONTENTS
PACKING LIST/ PARTS DISCLAIMER
INFORMATION PAGE
WIRING NOTICE
ENGINE COMPARTMENT / PASSENGER COMPARTMENT
FIGURES 1 & 2
DEFROST DUCT / FRESH AIR CAP & DRIVER AND PASSENGER SIDE
LOUVER INSTALLATION
FIGURES 3 & 4, 4a
EVAPORATOR INSTALLATION
FIGURES 5,5a & 6
FIREWALL COVER INSTALLATION
FIGURES 7 & 7a
CENTER LOUVER INSTALLATION
FIGURES 8 & 8a
DRAIN HOSE INSTALLATION & LUBRICATING O-RINGS, STANDARD HOSE KIT
& MODIFIED A/C HOSE KIT
FIGURES 9 & 10
HEATER HOSE & HEATER CONTROL VALVE INSTALLATION
FIGURE 11
A/C & HEATER HOSE ROUTING
FIGURE 12
FINAL STEPS & GLOVE BOX INSTALLATION
FIGURES 13 & 13a
DUCT HOSE ROUTING
FIGURE 14
EVAPORATOR HARD LINE AND BRACKET INSTALLATION
FIGURE 15
WIRING DIAGRAM
GEN IV WIRING CONNECTION INSTRUCTIONS
OPERATION OF CONTROLS.
TROUBLE SHOOTING
TROUBLE SHOOTING CONT.
DRIVER SIDE LOUVER TEMPLATE
PASSENGER SIDE LOUVER TEMPLATE
CENTER LOUVER TEMPLATE
FIREWALL COVER HOLE TEMPLATE
EVAPORATOR KIT PACKING LIST
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 2 OF 26
2
1969-70 MUSTANG w/o AC GEN IV
EVAPORATOR KIT
551170
EVAPORATOR KIT PACKING LIST
No.
1.
2.
QTY.
1
1
PART No.
763069
781069
DESCRIPTION
69-70 MUSTANG EVAP. SUB CASE
1969-70 MUSTANG w/o AC ACC. KIT
** BEFORE BEGINNING INSTALLATION OPEN ALL PACKAGES AND CHECK CONTENTS OF SHIPMENT.
PLEASE REPORT ANY SHORTAGES DIRECTLY TO VINTAGE AIR WITHIN 15 DAYS. AFTER 15 DAYS,
VINTAGE AIR WILL NOT BE RESPONSIBLE FOR MISSING OR DAMAGED ITEMS.
1
69-70 MUSTANG
EVAP. SUB CASE
763069
2
F
A
N
ACCESSORY KIT
781069
3
DASH
COLD
FLR
DEF
HOT
NOTE: IMAGES MAY NOT DEPICT ACTUAL PARTS AND QUANTITIES.
REFER TO PACKING LIST FOR ACTUAL PARTS AND QUANTITIES
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 3 OF 26
1969-70 MUSTANG w/o AC GEN IV
1969-70 MUSTANG
w/o FACTORY AIR
IMPORTANT NOTICE-PLEASE READ
FOR MAXIMUM SYSTEM PERFORMANCE VINTAGE AIR RECOMMENDS THE FOLLOWING:
THIS KIT DOES NOT CONTAIN HEATER HOSE. YOU MUST PURCHASE 8 FEET OF 5/8” DIA.
HEATER HOSE FROM VINTAGE AIR(31800-VUD) OR FROM YOU LOCAL PARTS RETAILER
SAFETY SWITCHES:
YOUR VINTAGE AIR SYSTEM IS EQUIPPED WITH A BINARY PRESSURE SAFETY SWITCH. A BINARY SWITCH
(11078-VUS) DISENGAGES THE COMPRESSOR CLUTCH IN CASE OF EXTREME LOW PRESSURE CONDITION
(REFRIGERANT LOSS) OR EXCESSIVELY HIGH HEAD PRESSURE (406 PSI), TO PREVENT COMPRESSOR DAMAGE
OR HOSE RUPTURE. A TRINARY SWITCH (11076-VUS) COMBINES HI/LO PRESSURE PROTECTION WITH AN
ELECTRIC FAN OPERATION SIGNAL AT 254 PSI., AND MAY BE SUBSTITUTED FOR USE WITH ELECTRIC
CONDENSER FANS. COMPRESSOR SAFETY SWITCHES ARE EXTREMELY IMPORTANT SINCE AN A/C SYSTEM
RELIES ON REFRIGERANT TO CARRY LUBRICATION THROUGH THE SYSTEM.
SERVICE INFO:
ATTENTION: SYSTEM COMPONENTS: THE COMPRESSOR, EVAPORATOR, CONDENSER & DRIER ARE CAPPED.
CAPS MAY BE UNDER PRESSURE WITH DRY NITROGEN; BE CAREFUL REMOVING CAPS. DO NOT REMOVE CAPS
PRIOR TO INSTALLATION. REMOVING CAPS PRIOR TO INSTALLATION WILL CAUSE COMPONENTS TO COLLECT
MOISTURE AND LEAD TO PREMATURE FAILURE AND REDUCED PERFORMANCE.
EVACUATE THE SYSTEM FOR 35-45 MINUTES WITH SYSTEM COMPONENTS (DRIER, COMPRESSOR, EVAPORATOR
AND CONDENSER) AT A TEMPERATURE OF AT LEAST 85° F. ON A COOL DAY THE COMPONENTS CAN BE HEATED
WITH A HEAT GUN OR BY RUNNING THE ENGINE WITH THE HEATER ON BEFORE EVACUATING. LEAK CHECK
AND CHARGE TO SPECIFICATIONS.
VINTAGE AIR SYSTEMS ARE DESIGNED TO OPERATE WITH R134a or R-12
REFRIGERANT ONLY ! USE OF ANY OTHER REFRIGERANTS RISKS A DANGER OF FIRE
AND COULD DAMAGE EITHER YOUR AIR CONDITIONING SYSTEM OR YOUR VEHICLE.
USE OF ANY OTHER REFRIGERANTS WILL VOID ALL WARRANTIES OF
THE AIR CONDITIONING SYSTEM AND COMPONE NTS. USE OF THE PROPER
TYPE AND AMOUNT OF REFRIGERANT IS CRITICAL TO PROPER SYSTEM
OPERATION. VINTAGE AIR RECOMMENDS OUR SYSTEMS BE CHARGED BY
WEIGHT WITH A QUALITY CHARGING STATION OR SCALE.
REFRIGERANT CAPACITIES FOR VINTAGE AIR SYSTEMS
(FOR OTHER SYSTEMS, CONSULT MANUFACTURER GUIDELINES)
134a SYSTEM
CHARGE WITH 1.8 lbs.
(1lbs. 12ozs) OF REFRIGERANT
R-12 SYSTEM
CHARGE WITH 2.0 lbs. OF REFRIGERANT
LUBRICANT CAPACITIES: NEW COMPRESSOR - NO ADDITIONAL OIL NEEDED
USED COMPRESSOR - CONSULT VINTAGE AIR
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 4 OF 26
4
1969-70 MUSTANG w/o AC GEN IV
IMPORTANTWIRING
WIRINGNOTICE-PLEASE
NOTICE-PLEASEREAD
READ
IMPORTANT
SOME VEHICLES MAY HAVE HAD SOME OR ALL OF THEIR RADIO INTERFERENCE CAPACITORS
REMOVED. THERE SHOULD BE A CAPACITOR FOUND AT EACH OF THE FOLLOWING LOCATIONS:
1. ON THE POSITIVE TERMINAL OF THE IGNITION COIL
2. IF THERE IS A GENERATOR, ON THE ARMATURE TERMINAL OF THE GENERATOR
3. IF THERE IS A GENERATOR, ON THE BATTERY TERMINAL OF THE VOLTAGE REGULATOR
MOST ALTERNATORS HAVE A CAPACITOR INSTALLED INTERNALLY TO ELIMINATE WHAT IS CALLED
'WHINING' AS THE ENGINE IS REVVED. IF WHINING IS HEARD IN THE RADIO, OR JUST TO BE EXTRA
CAUTIOUS, A RADIO INTERFERENCE CAPACITOR CAN BE ADDED TO THE BATTERY TERMINAL OF
THE ALTERNATOR.
IT IS ALSO IMPORTANT THAT THE BATTERY LEAD IS IN GOOD SHAPE AND THAT THE GROUND
LEADS ARE NOT COMPROMISED. THERE SHOULD BE A HEAVY GROUND FROM THE BATTERY TO
THE ENGINE BLOCK, AND ADDITIONAL GROUNDS TO THE BODY AND TO THE CHASSIS.
IF THESE PRECAUTIONS ARE NOT OBSERVED, IT IS POSSIBLE FOR VOLTAGE SPIKES TO BE PRESENT
ON THE BATTERY LEADS. THESE SPIKES COME FROM IGNITION SYSTEMS, CHARGING SYSTEMS,
AND FROM TURNING SOME OF THE VEHICLE'S OTHER SYSTEMS ON AND OFF. MODERN
COMPUTER OPERATED EQUIPMENT CAN BE SENSITIVE TO VOLTAGE SPIKES ON THEIR POWER
LEADS, WHICH CAN CAUSE UNEXPECTED RESETS, STRANGE BEHAVIOR, AND MAY ALSO CAUSE
PERMANENT DAMAGE.
VINTAGE AIR STRIVES TO HARDEN THEIR PRODUCTS AGAINST THESE TYPES OF ELECTRICAL NOISE,
BUT THERE IS A POINT WHERE A VEHICLE'S ELECTRICAL SYSTEM CAN BE DEGRADED SO MUCH
THAT NOTHING CAN HELP.
RADIO INTERFERENCE CAPACITORS SHOULD BE AVAILABLE AT MOST AUTO & TRUCK PARTS
SUPPLIERS. THEY TYPICALLY ARE CYLINDRICAL IN SHAPE, A LITTLE OVER AN INCH LONG, A LITTLE
OVER A HALF INCH IN DIAMETER, THEY HAVE A SINGLE LEAD COMING FROM ONE END OF THE
CYLINDER WITH A TERMINAL ON THE END OF THE WIRE, AND THEY WILL HAVE A MOUNTING CLIP
WHICH IS SCREWED INTO A GOOD GROUND ON THE VEHICLE. THE SPECIFIC VALUE OF THE
CAPACITANCE IS NOT TOO SIGNIFICANT, IN COMPARISON TO IGNITION CAPACITORS THAT ARE
MATCHED WITH THE COIL TO REDUCE PITTING OF THE POINTS.
CARE MUST BE TAKEN WHEN INSTALLING THE COMPRESSOR LEAD, NOT TO SHORT
IT TO GROUND. THE COMPRESSOR LEAD MUST NOT BE CONNECTED TO A CONDENSER
FAN OR ANY OTHER AUXILIARY DEVICE. SHORTING TO GROUND OR CONNECTING
TO A CONDENSER FAN OR ANY OTHER AUXILIARY DEVICE WILL CAUSE SEVERE DAMAGE
TO THE ECU.
WHEN INSTALLING GROUND LEADS ON GEN IV SYSTEMS, THE BLOWER CONTROL GROUND
AND ECU GROUND MUST BE CONNECTED DIRECTLY TO THE NEGATIVE BATTERY POST.
THE HEATER CONTROL VALVE IS A NORMALLY OPEN VALVE. IT MUST BE CONNECTED TO
THE ECU TO BLOCK WATER FLOW IN AC MODE.
5
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 5 OF 26
1969-70 MUSTANG w/o AC GEN IV
BEFORE STARTING THE INSTALLATION, CHECK THE FUNCTION
OF THE VEHICLE (HORN, LIGHTS,ETC.) FOR PROPER OPERATIONS.
STUDY THE INSTRUCTIONS, ILLUSTRATIONS, & DIAGRAMS.
ENGINE COMPARTMENT
REMOVE THE FOLLOWING:
BATTERY (RETAIN).
DRAIN RADIATOR
HEATER HOSES(DISCARD).
CONDENSER ASSEMBLY & INSTALLATION
REFER TO SEPARATE INSTRUCTIONS INCLUDED WITH
THE CONDENSER KIT TO INSTALL THE CONDENSER.
BINARY SWITCH INSTALLATION ( REFER TO CONDENSER INSTRUCTIONS)
COMPRESSOR & BRACKETS
REFER TO SEPARATE INSTRUCTIONS INCLUDED WITH THE
BRACKET KIT TO INSTALL THE COMPRESSOR BRACKET.
PASSENGER COMPARTMENT
NOTE: REMOVAL OF DASHBOARD REQUIRED TO INSTALL THE EVAPORATOR. VINTAGE AIR
RECOMMENDS THAT YOU UTILIZE THE FACTORY SERVICE MANUAL WHEN YOU DISASSEMBLE
AND REASSEMBLE THE DASHBOARD.
REMOVE THE FOLLOWING:
REMOVE DASH PAD, INSTRUMENT PANEL, PASSENGER SIDE PANEL AND LOWER PASSENGER SIDE
DASHBOARD (RETAIN SCREWS) SEE FIGURE 1.
GLOVE BOX (RETAIN) SEE FIGURE 1.
HEATER ASSEMBLY AND ALL RELATED DUCTING (DISCARD), RETAIN SCREWS.
SEE FIGURE 2.
CONTROL PANEL ASSEMBLY (RETAIN CONTROL PANEL) SEE FIGURE 1.
REFER TO CONTROL PANEL CONVERSION KIT INSTRUCTIONS FOR INSTALLATION OF CONTROLS.
REMOVE OEM DEFROST DUCT ASM SEE FIGURE 2.
DASH PAD
INSTRUMENT
PANEL
FIGURE 1
CONTROL
PANEL
DEFROST DUCT
ASM
GLOVE
BOX
PASSENGER SIDE
PANEL
LOWER PASSENGER
SIDE DASHBOARD
HEATER
ASSEMBLY
FIGURE 2
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 6 OF 26
6
1969-70 MUSTANG w/o AC GEN IV
DEFROST DUCT/ FRESH AIR CAP INSTALLATION
INSTALL DEFROST DUCT UNDER DASH AS SHOWN IN FIGURE 3 BELOW. SECURE USING OEM NUTS
w/ (3) 3/16 SAE FLAT WASHERS.
HOLD FRESH AIR CAP UNDER DASH AND MARK THE (3) MOUNTING HOLES.
DRILL (3) 1/8” MOUNTING HOLES UNDER DASH.
APPLY A 1/4” BEAD OF SILICONE AROUND THE BACK SIDE OF THE FRESH AIR CAP AS SHOWN IN
FIGURE 3, BELOW.
SECURE FRESH AIR CAP TO FRESH AIR HOLE USING (3) #10 X 1/2 SHEET METAL SCREWS AS SHOWN
IN FIGURE 3 BELOW.
DRILL
HOLES
SILICONE
(3) OEM
STAR NUTS
DEFROST
DUCT
605169
(3) 3/16
SAE FLAT
WASHERS
FRESH AIR
CAP
605174
(3) 10 X 1/2
SHEET METAL
SCREW
FIGURE 3
DRIVER AND PASSENGER SIDE LOUVER INSTALLATION
CUT OUT TEMPLATE PROVIDED ON PAGE 22. PLACE THE DRIVER SIDE TEMPLATE ON THE DASH BY
ALIGNING THE LEFT SIDE OF THE TEMPLATE AGAINST THE EDGE OF THE DASH, THEN ALIGN THE
BOTTOM OF THE TEMPLATE TO BOTTOM OF DASH AS SHOWN IN FIGURE 4.
CUT OUT TEMPLATE PROVIDED ON PAGE 23. PLACE THE PASSENGER SIDE TEMPLATE ON THE DASH
BY ALIGNING THE RIGHT SIDE OF THE TEMPLATE AGAINST THE EDGE OF THE DASH, THEN ALIGN
THE BOTTOM OF THE TEMPLATE TO BOTTOM OF DASH AS SHOWN IN FIGURE 4.
ONCE TEMPLATE IS ALIGNED CORRECTLY, USE A CENTER PUNCH TO MARK THE HOLE ON THE
DASH. REMOVE TEMPLATE. USE A 2 3/4 HOLE SAW TO CUT HOLE IN DASH, SEE FIGURE 4 BELOW.
INSTALL LOUVERS IN DASH AS SHOWN IN FIGURE 4a BELOW.
DASH
DRIVER SIDE
TEMPLATE
2 1/2 HOSE
ADAPTER
PASSENGER SIDE
LOUVER BRKT
642075
DRILL 2 3/4
HOLE
FIGURE 4
7
TEMPLATE
DRILL 2 3/4
HOLE
LOUVER
490535
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 7 OF 26
LOUVER BEZEL
605181
FIGURE 4a
1969-70 MUSTANG w/o AC GEN IV
EVAPORATOR INSTALLATION
USE TEMPLATE PROVIDED ON PAGE 25. ALIGN TEMPLATE WITH OEM BLOWER MOTOR MOUNTING
HOLES & DRILL (6) 3/16 HOLES IN FIREWALL FROM INSIDE UNDER DASH, SEE FIGURE 5a.
ON A WORK BENCH, INSTALL EVAPORATOR REAR BRACKET AND HARDLINES WITH PROPERLY LUBRICATED O-RINGS.
(SEE FIGURE 10, PAGE 11, AND FIGURE 15, PAGE 16.)
REMOVE 2 OEM HEATER PLUGS IN FIREWALL, SEE FIGURE 7 PAGE 9.
INSTALL FRONT MOUNTING BRACKET ON EVAPORATOR USING (2) 1/4-20 X 1/2 HEX BOLTS AND TIGHTEN AS
SHOWN IN FIGURE 5 BELOW.
LIFT EVAPORATOR UNIT UP UNDER THE DASHBOARD SEE FIGURE 6. SECURE LOOSELY TO THE FIREWALL FROM THE
ENGINE COMPARTMENT SIDE USING (2) 1/4-20 NUT AND WASHER, SEE FIGURE 6 BELOW.
USING (2) #14 X 3/4 SHEET METAL SCREW w/ 1/4 FLAT WASHER SECURE THE FRONT EVAPORATOR MOUNTING
BRACKET TO THE INNER COWL. SEE FIGURE 6 BELOW.
VERIFY THAT EVAPORATOR UNIT IS LEVEL AND SQUARE TO THE DASH, THEN TIGHTEN ALL MOUNTING BOLTS.
(NOTE: TIGHTEN THE BOLT ON FIREWALL FIRST, THEN THE FRONT MOUNTING BRACKET SCREWS.)
EVAP FRONT
BRKT
641271
FIGURE 5
DRIVER SIDE EVAP
MOUNTING HOLE
LES
ENT HO
NM
(4) ALIG
MOTOR
BLOWER TIN G
MOUN
HOLE
OEM HEATER
LINE HOLES
BLOWER
MOTOR G
TIN
MOUN
HOLE
PASSENGER SIDE EVAP
MOUNTING HOLE
6
(6) 3/1
HOLES
NG w/o
R
0 MUSTA
1969-7 WALL COVE
FIRE
PL ATE
HOLE TEM
AC
TER
BLOWER
MOTOR G
TIN
MOUN
HOLE
OEM HEA
HOLE
BLOWER
MOTOR G
E OF CAR
TIN
E IN SID
MOUN
THIS SID
HOLE
FIGURE 5a
PASSENGER SIDE EVAP
MOUNTING HOLE
(2) #14 X 3/4
SHEETMETAL
SCREW
w/ 1/4
FLAT WASHER
DRIVER SIDE EVAP
MOUNTING HOLE
FIGURE 6
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 8 OF 26
8
1969-70 MUSTANG w/o AC GEN IV
FIREWALL COVER INSTALLATION
INSTALL (3) GROMMETS ON FIREWALL COVER AS SHOWN IN FIGURE 7, BELOW.
APPLY A 1/4 BEAD OF SILICONE AROUND THE BACK SIDE OF THE FIREWALL COVER AS SHOWN IN
FIGURE 7a, BELOW.
SECURE FIREWALL COVER TO FIREWALL USING (6) #14 X 3/4 SHEET METAL SCREWS, SEE FIGURE 7,
BELOW.(NOTE: FIREWALL COVER INSTALLS ON ENGINE SIDE OF FIREWALL.)
ENGINE
COMPARTMENT
SIDE OF
FIREWALL
FIGURE 7a
SILICONE
(4) OEM
BLOWER MOTOR
MOUNTING HOLES
OEM
HEATER HOLE
IN FIREWALL
FIREWALL
COVER
642071
OEM HEATER
LINE HOLES
(REMOVE PLUG)
GROMMET
33137-VUI
GROMMET
33144-VUI
OEM
HOLES
FIGURE 7
GROMMET
33135-VUI
(6) #14 X 3/4
SHEET METAL
SCREWS
9
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 9 OF 26
1969-70 MUSTANG w/o AC GEN IV
CENTER LOUVER INSTALLATION (OPTION 1)
CUT OUT CENTER LOUVER TEMPLATE PROVIDED ON PAGE 24. ALIGN
CENTER LOUVER TEMPLATE ON DASH PAD AS SHOWN IN
FIGURE 8a.
MARK CENTER LOUVER OPENING ON DASH PAD. ONCE
CENTER LOUVER OPENING IS MARKED REMOVE TEMPLATE
AND CAREFULLY CUT OUT OPENING IN DASH PAD.
INSTALL CENTER LOUVER ASM AS SHOWN IN
FIGURE 8.
CUT OUT
TEMPLATE
FIGURE 8a
CENTER LOUVER
ASM
590070
FIGURE 8
ASSEMBLED VIEW
UNDER DASH CENTER LOUVER INSTALLATION (OPTION 2)
INSTALL UNDER DASH LOUVERS USING (3) #8 X 1/2 PAN HEAD SCREWS.
UNDER DASH
LOUVER
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 10 OF 26
10
1969-70 MUSTANG w/o AC GEN IV
DRAIN HOSE INSTALLATION
LOCATE EVAPORATOR DRAIN ON BOTTOM OF EVAPORATOR CASE.
IN-LINE WITH THE DRAIN, LIGHTLY MAKE A MARK ON
THE FIREWALL. MEASURE ONE INCH DOWN AND DRILL
A 5/8 HOLE THROUGH THE FIREWALL. SEE FIGURE 9
INSTALL DRAIN HOSE TO BOTTOM OF EVAPORATOR
UNIT AND ROUTE THROUGH FIREWALL.
SEE FIGURE 9.
1”
DRAIN
HOSE
DRAIN
FIGURE 9
LUBRICATING O-RINGS
O-RING
#6 O-RING
#8 O-RING
MALE FEMALE
NUT
INSERT
SUPPLIED OIL
FOR O-RINGS
FOR A PROPER SEAL OF FITTINGS:
INSTALL SUPPLIED O-RINGS AS SHOWN
AND LUBRICATE WITH SUPPLIED OIL.
TWIST WITH
THIS
WRENCH
HOLD WITH
THIS
WRENCH
#10 O-RING
FIGURE 10
STANDARD HOSE KIT
O-RING,
SLIDE OVER
MALE INSERT TO
SWAGED LIP
O-RING
LOCATE THE #8 COMPRESSOR A/C HOSE. LUBRICATE (2) #8 O-RINGS (SEE FIGURE 10, ABOVE) AND CONNECT
THE 45° FITTING TO THE #8 DISCHARGE PORT ON THE COMPRESSOR. ROUTE THE STR FEMALE w/ 134a
SERVICE PORT FITTING TO THE #8 CONDENSER HARDLINE COMING THROUGH THE RADIATOR CORE SUPPORT.
SEE FIGURE 12, PAGE 13. TIGHTEN EACH FITTING CONNECTION AS SHOWN IN FIGURE 10 ABOVE.
LOCATE THE #10 COMPRESSOR A/C HOSE. LUBRICATE (2) #10 O-RINGS AND CONNECT THE 90° FEMALE
w/ 134a SERVICE PORT FITTING TO THE #10 SUCTION PORT ON THE COMPRESSOR, ROUTE THE 135° FEMALE
FITTING TO THE #10 EVAPORATOR HARDLINE COMING THROUGH THE FIREWALL. SEE FIGURES 11, PAGE 12 &
FIGURE 12, PAGE 13. TIGHTEN EACH FITTING CONNECTION AS SHOWN IN FIGURE 10 ABOVE.
(NOTE: WRAP THE #10 FITTING CONNECTIONS WITH PRESS TAPE. SEE FIGURE 11, PAGE 12 & FIGURE 12, PAGE 13.
LOCATE THE #6 EVAP/DRIER A/C HOSE. LUBRICATE (2) #6 O-RINGS AND CONNECT THE STR FEMALE FITTING
TO THE #6 DRIER HARDLINE COMING THROUGH THE RADIATOR CORE SUPPORT. ROUTE THE 90° FEMALE
FITTING TO THE #6 EVAPORATOR HARDLINE COMING THROUGH THE FIREWALL. SEE FIGURES 11, PAGE 12 &
FIGURE 12, PAGE 13. TIGHTEN EACH FITTING CONNECTION AS SHOWN IN FIGURE 10 ABOVE.
USE (6) TIE WRAPS TO SECURE THE #6 A/C HOSE TO THE EXPORT BRACE AS SHOWN IN FIGURE 12, PAGE 13.
MODIFIED A/C HOSE KIT
REFER TO SEPARATE INSTRUCTIONS INCLUDED WITH MODIFIED HOSE KIT.
11
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 11 OF 26
1969-70 MUSTANG w/o AC GEN IV
HEATER HOSE & HEATER CONTROL VALVE INSTALLATION
ROUTE A PIECE OF HEATER HOSE FROM THE WATER PUMP TO THE HEATER LINE COMING THROUGH THE FIREWALL
AS SHOWN IN FIGURE 11, BELOW. SECURE USING HOSE CLAMPS.
ROUTE A PIECE OF HEATER HOSE FROM THE INTAKE TO THE HEATER LINE COMING THROUGH THE FIREWALL
AS SHOWN IN FIGURE 11 BELOW. NOTE: INSTALL HEATER CONTROL VALVE IN-LINE WITH INTAKE MANIFOLD
(PRESSURE SIDE) HEATER HOSE, SECURE USING HOSE CLAMPS AS SHOWN IN FIGURE 11 BELOW.
NOTE PROPER FLOW DIRECTION.)
ECU
MODULE
#10 SUCTION
LINE (INSULATED)
PRESS
TAPE
FIREWALL
#10 SUCTION
HOSE
FR
OM
TO HTR
EV
AP CNT
FR
O R RL
OM
AT VLV
TO EV
OR
W A PO
AT
ER
RA
PU TOR
MP
FL
OW
FRO
MA M IN
NIF TAK
OL E
D
EXPANSION
VALVE
HEATER
HOSE
FIREWALL
COVER
642071
O-RINGS
#6 A/C HOSE
FIGURE 11
12
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 12 OF 26
13
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 13 OF 26
HEATER HOSE
(HEATER CORE/
WATER PUMP)
PRESS
TAPE
HEATER HOSE
(HEATER CNTRL
VALVE/INTAKE)
(6)TIE
WRAP
OUT
IN
COMPRESSOR
SAFETY SWITCH
(BINARY TYPE)
SCREW ON DRIER
(REFER TO
CONDENSER
INSTRUCTIONS)
#6 DRIER TO
CORE SUPPORT
HARDLINE
081095
#8 CONDENSER TO
CORE SUPPORT
HARDLINE
081096
INNER
FENDERWELL
FIGURE 12
#8
DISCHARGE
HOSE
#6
HOSE
#10
SUCTION
HOSE
NOTE: VINTAGE AIR SYSTEMS REQUIRE
(2) 5/8 HOSE NIPPLES (NOT SUPPLIED)
AC & HEATER HOSE ROUTING
1969-70 MUSTANG w/o AC GEN IV
1969-70 MUSTANG w/o AC GEN IV
FINAL STEPS
INSTALL DUCT HOSES AS SHOWN IN FIGURE 14, PAGE 15.
ROUTE A/C WIRES THROUGH 3/8 GROMMENT AS SHOWN ON FIGURE 13a
(12 VOLT/ GROUND/ BINARY SWITCH/ HEATER VALVE).
INSTALL CONTROL PANEL ASM.
PLUG THE WIRING HARNESS IN THE ECU MODULE ON SUB CASE AS SHOWN IN FIGURE 14, PAGE 15
(WIRE ACCORDING TO WIRING DIAGRAM ON PAGE 17 AND 18)
GLOVE BOX INSTALLATION (SEE FIGURE 13)
REINSTALL ALL PREVIOUSLY REMOVED ITEMS (BATTERY).
FILL RADIATOR WITH AT LEAST A 50/50 MIXTURE OF APPROVED ANTIFREEZE AND DISTILLED WATER.IT IS THE
OWNER'S RESPONSIBILITY TO KEEP THE FREEZE PROTECTION AT THE PROPER LEVEL FOR THE CLIMATE IN
WHICH THE VEHICLE IS OPERATED. FAILURE TO FOLLOW ANTIFREEZE RECOMMENDATIONS WILL CAUSE
HEATER CORE TO CORRODE PREMATURELY AND POSSIBLY BURST IN AC MODE AND/OR FREEZING WEATHER,
VOIDING YOUR WARRANTY.
DOUBLE CHECK ALL FITTINGS, BRACKETS AND BELTS FOR TIGHTNESS.
VINTAGE AIR RECOMMENDS THAT ALL AC SYSTEMS BE SERVICED BY A CERTIFIED AUTOMOTIVE AIR
CONDITIONING TECHNICIAN.
EVACUATE THE SYSTEM FOR A MINIMUM OF 45 MINUTES PRIOR TO CHARGING AND LEAK CHECK PRIOR
TO SERVICING.
CHARGE THE SYSTEM TO THE CAPACITIES STATED ON THE INFORMATION PAGE (PAGE 4) OF THIS
INSTRUCTION MANUAL.
SEE OPERATION OF CONTROLS PROCEDURES PAGE 19.
GLOVE BOX INSTALLATION
INSTALL GLOVE BOX WITH OEM SCREWS. SEE FIGURE 13.
GROMMET
FIREWALL
COVER
GLOVE BOX
FIGURE 13a
FIGURE 13
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 14 OF 26
14
1969-70 MUSTANG w/o AC GEN IV
DUCT HOSE ROUTING
CONTROL PANEL
HARNESS
TO ECU
232006-VUR
PASS. SIDE
DEF. DUCT
2” x 12”
PASS. SIDE
LOUVER
2 1/2” x 32”
PLUG
FROM
CONTROL
WIRING
HARNESS
232006-VUR
DRIVER SIDE
DEF. DUCT
2” x 14”
PLUG
FROM
WIRING
HARNESS
232001-VUR
DRIVER SIDE
LOUVER
2 1/2” x 30”
CENTER LOUVER
PASS. SIDE
2
CENTER LOUVER 1/2” x 32”
DRIVER SIDE
2 1/2” x 32”
FIGURE 14
15
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 15 OF 26
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 16 OF 26
16
#10 SUCTION
LINE
081092
PRESS TAPE
FIGURE 15
#6
O-RING
(33857-VUF)
(33859-VUF)
1/4-20 X 1/2
BOLT
(LOCATED ON
SUB CASE)
TWIST WITH
THIS
WRENCH
#10 O-RING
(33859-VUF)
DRIVER SIDE EVAP
REAR BRKT
641273
18289-VUB
1/4-20 X 1
COARSE BOLT
#6 LIQUID LINE
081091
PASS SIDE EVAP
REAR BRKT
641272
NOTE: AFTER INSTALLING
# 10 SUCTION LINE
WRAP ALL EXPOSED METAL
(FITTINGS & TUBE)
ECU MODULE
WITH SUPPLIED
PRESS TAPE.
#10 O-RING
EVAPORATOR HARD
LINE INSTALLATION
LUBRICATE O-RING
(SEE FIGURE 10,
PAGE 11.)
FIGURE 8
HOLD WITH
THIS WRENCH
HEATER LINE
(EVAP TO WATER PUMP)
081094
HEATER LINE
(EVAP TO INTAKE)
081093
189125-MUR
1/4 PUSH NUT
BOLT RETAINER
BRACKET
1969-70 MUSTANG w/o AC GEN IV
1969-70 MUSTANG w/o AC GEN IV
WIRING DIAGRAM
RED
WHT
WHT/BLU
NA
VIEWED FROM BOARD TOP SIDE
RED
WHT
WHT/RED
JF8
COLD
HOT
RED
WHT
WHT/YEL
RED
WHT
WHT/GRN
VIEWED FROM
WIRE SIDE
JM3
OPTIONAL:
WIDE OPEN THROTTLE
SWITCH CONTACTS
CLOSE ONLY AT
FULL THROTTLE,
WHICH DISABLES
AC COMPRESSOR
DASH
FLR
DEF
RED
GRN
YEL
BLU
GRN
BLK
STEPPER
DASH/FLOOR
RED
GRN
YEL
BLU
GRN
BLK
JM4
FAN
RED
GRN
YEL
BLU
GRN
BLK
GRY
JM5
RED
PRGM
YEL/BLK
WHT
N/A TACH
DASH LAMP
(NOT USED)
LT BLU
GRN
GRY
TAN
VIO
ORA
STEPPER
DEFROST/PLENUM
STEPPER
TEMPERTURE BLEND
NOT USED
JM6
JM9
WIDE OPEN
THROTTLE
SWITCH
(OPTIONAL)
JF8
JM8
JM2
BLK
BLK
JM1
RUN
GENIV WIRING DIAGRAM
REVISION B, 2006-05-04
BAT
IGNITION
SWITCH
EVAPORATOR
TEMPERATURE
SENSOR
VIO
GEN-IV ECU
+ 12v
WHT
RED
RED
WHT
WHT
30
85
87
30
86
85
87
86
COMPRESSOR
RELAY
NEG
BLOWER MOTOR
BLK
YEL
BLK
HEATER
CONTROL
VALVE
RELAY
GRN
DK BLU
DK BLU
WARNING: ALWAYS MOUNT CIRCUIT
BREAKER UNDER THE HOOD IN THE ENGINE
COMPARTMENT AND AS CLOSE TO
THE BATTERY AS POSSIBLE.
WHT
BINARY
OR TRINARY
SAFETY
SWITCH
HCV
DRIER
BATTERY
CMPR
NOTE:
17
POS
RED
BSC
CIRCUIT
BREAKER
30 AMP
ORA
GRY
SHLD
RED
BLWR-NEG
PWM
RED
BLWR-POS
BAT-NEG
SHLD
RED
RED
RED
BAT-POS
= CHASSIS
GROUND
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 17 OF 26
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 18 OF 26
18
RED
BLU
E
CIRCUIT BREAKER
30 AMP
CONNECT
RED
WH
T
WH
T
(SUPPLIED
GROUND
WIRE, NOT
CHASSIS
PART OF
GROUND
HARNESS)
CONNECT
GRN
A/C
COMPRESSOR
RELAY
RED
WH
T
CONNECT
WARNING:
ALWAYS MOUNT CIRCUIT
BREAKER UNDER THE HOOD
IN THE ENGINE COMPARTMENT
AND AS CLOSE TO THE
BATTERY AS POSSIBLE.
RED
WH
T
HEATER
CONTROL
VALVE
HEATER
CONTROL
VALVE RELAY
NOTE:
MOUNT RELAYS
IN DESIRED
LOCATION
UNDER DASH
WHT
RED
WH
T
WH
T
+
CONNECT
BACK SIDE
OF EVAPORATOR
BATTERY
NOTE: CONNECT WHITE
WIRES DIRECTLY TO
( ) BATTERY TERMINAL
COMPRESSOR
K
BLAC
FRONT SIDE
OF EVAPORATOR
CONNECT
LET
IGNITION
SWITCH
(IGNITION HOT
TERMINAL)
RUN
BAT
+12 V
NOTE:
YELLOW, ORANGE
& TAN COMING FROM
HARNESS ARE NOT USED.
GRAY WIRES IS USED
FOR PROGRAMING
CONTROLS IF APPLICABLE
CONNECT
VIO
CONTROL
WIRING
HARNESS
WIRING
HARNESS
CONNECT
REFER TO CONTROL
PANEL INSTRUCTIONS
AND PLUG IN ACCORDINGLY
NOTE: IF USING TRINARY
SAFETY SWITCH- REFER TO
WIRING SCHEMATIC SUPPLIED
WITH TRINAY SAFETY SWITCH
FOR PROPER WIRING INSTRUCTIONS
BINARY
SAFETY
SWITCH
BLUE
CONNECT
WHT
GEN IV WIRING
CONNECTION
INSTRUCTIONS
1969-70 MUSTANG w/o AC GEN IV
1969-70 MUSTANG w/o AC GEN IV
OPERATION OF CONTROLS
NOTE: WHEN BATTERY POWER IS FIRST CONNECTED TO THE ECU, THE COMPUTER GOES THROUGH AN INITIALIZATION
SEQUENCE. THIS INITIALIZATION MAY TAKE UP TO 30 SECONDS. DURING INITIALIZATION THE BLOWER WILL NOT OPERATE,
BUT THE DOORS INSIDE THE UNIT WILL BE OPERATING. A LOW BATTERY OR DISCONNECTING THE BATTERY MAY ALSO
TRIGGER A RE-INITIALIZATION. DURING START UP, A LOW BATTERY MAY DROP BELOW 7 VOLTS, TRIGGERING RE-INITIALIZATION.
MODE
LEVER
SYSTEM OFF
A/C MODE
BLOWER
SPEED
F
A
N
F
A
N
DEF
FLR
DASH
HOT
COLD
DEF
FLR
DASH
HOT
COLD
THERMOSTAT
LEVER
BLOWER SPEED
THIS LEVER CONTROLS
THE BLOWER SPEED,
FROM OFF TO HI
MODE LEVER
SLIDE THE LEVER TO
THE “DASH” POSITION
THERMOSTAT LEVER
IN A/C MODE SLIDE THE
THERMOSTAT LEVER ALL THE WAY
LEFT TO THE COLD POSITION,
FOR MAXIMUM COOLING
(SLIDE LEVER LEFT OR RIGHT TO
ADJUST DESIRED TEMPERATURE)
BLOWER SPEED
SLIDE LEVER UP
TO DESIRED BLOWER SPEED,
FROM OFF TO HI
MODE LEVER
SLIDE THE LEVER TO
THE “DASH” POSITION
HEAT MODE
F
A
N
DASH
COLD
BLOWER SPEED
SLIDE LEVER UP
TO DESIRED BLOWER SPEED,
FROM OFF TO HI
MODE LEVER
SLIDE THE LEVER TO
THE “FLR” POSITION
19
FLR
THERMOSTAT LEVER
IN A/C MODE SLIDE THE
THERMOSTAT LEVER ALL THE
WAY LEFT TO THE COLD POSITION
TO ENGAGE COMPRESSOR,
FOR MAXIMUM COOLING
(SLIDE LEVER LEFT OR RIGHT TO
ADJUST DESIRED TEMPERATURE)
DEFROST/ DE-FOG MODE
DEF
HOT
THERMOSTAT LEVER
IN HEAT MODE SLIDE THE
THERMOSTAT LEVER ALL THE
WAY RIGHT TO THE HOT POSITION,
FOR MAXIMUM HEATING
((SLIDE LEVER LEFT OR RIGHT TO
ADJUST DESIRED TEMPERATURE)
F
A
N
DASH
COLD
BLOWER SPEED
SLIDE LEVER UP
TO DESIRED BLOWER SPEED,
FROM OFF TO HI
MODE LEVER
SLIDE THE LEVER TO
THE “DEF” POSITION
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 19 OF 26
FLR
DEF
HOT
THERMOSTAT LEVER
IN DEF MODE SLIDE THE
THERMOSTAT LEVER ALL THE WAY
LEFT TO THE COLD POSITION
TO ENGAGE COMPRESSOR.
FOR MAXIMUM COOLING
(SLIDE LEVER LEFT OR RIGHT TO
ADJUST DESIRED TEMPERATURE)
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 20 OF 26
3. COMPRESSOR WILL NOT TURN
OFF (ALL OTHER FUNCTIONS
WORK)
2. COMPRESSOR WILL NOT TURN
ON (ALL OTHER FUNCTIONS
WORK)
BLOWER STAYS ON HIGH
SPEED WHEN IGNITION IS ON
OR OFF.
1. BLOWER STAYS ON HIGH
SPEED WHEN IGNITION IS ON
SYMPTOM
20
SEE BLOWER SWITCH CHECK PROCEDURE
(CONTACT VINTAGE AIR TECH SUPPORT)
LOSS OF GROUND ON THIS WIRE WILL RENDER
CONTROL HEAD INOPERABLE
NOTES
REPLACE ECU.
REPLACE RELAY
REFER TO INTSRUCTIONS "'55-56 CONTROL PANEL
CONVERSION REV B 6 17 05" PDF OR 903055-PCA REV C
8/10/05 OR LATER INSRUCTION MANUAL.
CHECK FOR FAULTY A/C RELAY
FOR '55-56 CHEV. CHECK FOR PROPER PANEL
CONVERSION. CONTROL LEVERS SHOULD TRAVEL
TO WITHIN 1/8" OF BOTH ENDS OF THE SLOTS.
CHECK CONTINUITY ACROSS SWITCH
(CHECK FOR FAULTY PRESSURE SWITCH)
EARLY INSTRUCTIONS ON '55-56 CHEV. DID NOT
INCLUDE PANEL MOD PROCEEDURE FOR
CONTROL WITH LOWER POT BRACKET OFFSET
BACK FROM CASTING. IF LEVERS ONLY TRAVEL
2/3 TO 3/4 UP, THIS PROCEEDURE MUST BE
PERFORMED
RED WIRE @ A/C POT SHOULD HAVE APPROX. 5V
WITH IGNITION ON. WHITE WIRE WILL HAVE
CONTINUITY TO CHASSIS GROUND, WHITE/BLUE
WIRE SHOULD VARY BETWEEN 0V AND 5V WHEN
LEVER IS MOVED UP AND DOWN.
CHECK TWO PIN CONNECTOR AT ECU
HOUSING.
CHECK FOR DISCONNECTED OR FAULTY
THERMISTOR.
REPAIR/REPLACE POT/CONTROL WIRING
REPLACE SWITCH
CHECK CONTINUITY TO GROUND ON WHITE CONTROL
HEAD WIRE. CHECK FOR 5V ON RED CONTROL HEAD
WIRE.
CHECK FOR FAULTY A/C POT OR ASSOC. WIRING
SYSTEM IS CHARGED
CHECK FOR FAULTY A/C POT OR ASSOC. WIRING
TO CHECK FOR PROPER POT FUNCTION, CHECK
VOLTAGE AT WHITE/BLUE WIRE. VOLTAGE
SHOULD BE BETWEEN 0 AND 5V, AND WILL VARY
WITH POT LEVER POSITION.
DISCONNECTED OR FAULTY THERMISTOR WILL
CAUSE COMPRESSOR TO BE DISABLED.
CHARGE SYSTEM OR BYPASS PRESSURE SWITCH .
DANGER- NEVER BYPASS SAFETY SWITCH WITH
ENGINE RUNNING, SERIOUS INJURY CAN RESULT
REPLACE BSC. (THIS WILL REQUIRE EVAPORATOR TO BE NO OTHER PART REPLACEMENTS SHOULD BE
REMOVED FROM VEHICLE. )
NECESSARY.
CHECK TO INSURE THAT NO BSC WIRING IS DAMAGED OR
SHORTED TO VEHICLE GROUND. THE BSC OPERATES
THE BLOWER BY GROUND SIDE PWM SWITCHING. THE
POSITIVE WIRE TO THE BLOWER WILL ALWAYS BE HOT.
IF THE "GROUND" SIDE OF THE BLOWER IS SHORTED TO
CHASSIS GROUND, THE BLOWER WILL RUN ON HI.
BE SURE SMALL, 20GA. WHITE GROUND WIRE IS
CONNECTED TO THE BATTERY GROUND POST. IF IT IS,
REPLACE ECU.
VERIFY ALL PINS ARE INSERTED INTO PLUG. INSURE NO
PINS ARE BENT OR DAMAGED IN ECU.
VERIFY CONTINUITY TO CHASSIS GROUND WITH WHITE
CONTROL HEAD WIRE AT VARIOUS POINTS.
ACTIONS
SYSTEM MUST BE CHARGED FOR COMP. TO
ENGAGE.
UN-PLUG 3 WIRE BSC CONTROL CONNECTOR
FROM ECU. IF BLOWER STAYS RUNNING, THE BSC
IS EITHER IMPROPERLY WIRED, OR DAMAGED.
CHECK FOR DAMAGED PINS OR WIRES IN CONTROL
HEAD PLUG.
CHECK FOR DAMAGED GROUND WIRE (WHITE) IN
CONTROL HEAD HARNESS.
CHECK FOR DAMAGED BLOWER SWITCH OR POT
AND ASSOCIATED WIRING.
UN-PLUG 3 WIRE BSC CONTROL CONNECTOR
FROM ECU. IF BLOWER SHUTS OFF, ECU IS EITHER
IMPROPERLY WIRED, OR DAMAGED.
CHECKS
SYSTEM IS NOT CHARGED
ALL OTHER FUNCTIONS WORK
NO OTHER FUNCTIONS WORK
CONDITION
TROUBLE SHOOTING INFORMATION
1969-70 MUSTANG w/o AC GEN IV
CHECK FOR DAMAGED STEPPER MOTOR OR
WIRING
CHECK FOR DAMAGED MODE SWITCH OR POT AND
ASSOCIATED WIRING
CHECK FOR OBSTRUCTED OR BINDING MODE
DOORS
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 21 OF 26
CONNECT TO GAUGE BACK LIGHT WIRE (0-12V) WHICH
WHICH CONTROLS DIMMING OF PANEL BACK LIGHT
CONNECT TO GAUGE BACK LIGHT WIRE (0-12V) WHICH
WHICH CONTROLS DIMMING OF PANEL BACK LIGHT
TAN WIRE IN MAIN HARNESS IS NOT CONNECTED
TO 0-12V GAUGE BACK LIGHT WIRE.
TAN WIRE IN MAIN HARNESS NOT CONNECTED.
VINTAGE AIR SUPPLIED PANELS
ONLY.
VINTAGE AIR SUPPLIED PANELS
ONLY.
9. BACKLIGHTING ON CONTROL
PANEL ALWAYS ON.
10. BACKLIGHTING ON CONTROL
PANEL ALWAYS OFF.
RUN RED POWER WIRE DIRECTLY TO BATTERY.
THIS IS AN INDICATOR THAT THE SYSTEM HAS
BEEN RE-SET. BE SURE THE RED POWER WIRE IS
ON THE BATTERY POST AND NOT ON A SWITCHED
SOURCE. ALSO, IF THE SYSTEM IS PULLED BELOW
7V EVEN FOR A SPLIT SECOND, THE SYSTEM WILL
RE-SET.
8. WHEN THE IGNITION IS TURNED
ON, THE BLOWER MOMENTARILY
COMES ON, THEN SHUTS OFF.
THIS IS WITH THE BLOWER
SWITCH IN THE OFF POSITION.
REPAIR OR REPLACE
INSURE ALL SYSTEM GROUNDS AND POWER
CONNECTIONS ARE CLEAN AND TIGHT.
CHARGE BATTERY
CHECK FOR POSITIVE POWER AT HEATER VALVE GREEN
WIRE. AND BLOWER RED WIRE. CHECK FOR GROUND
ON CONTROL HEAD WHITE WIRE.
VERIFY PROPER METER FUNCTION BY CHECKING A
KNOWN GOOD BATTERY'S VOLTAGE.
INSTALL CAPACITORS ON IGN. COIL, AND ALTERNATOR.
ENSURE GOOD GROUND AT ALL POINTS.RE-LOCATE COIL
AND ASSOCIATED WIRING AWAY FROM ECU AND ECU
WIRING. CHECK FOR BURNED OR LOOSE PLUG WIRES.
CHECK FOR DAMAGED SWITCH OR POT AND
ASSOCIATED WIRING
BATTERY VOLTAGE IS AT LEAST CHECK FOR AT LEAST 12V BETWEEN GREEN
12V
HEATER VALVE WIRE AND CHASSIS GROUND.
CHECK FOR FAULTY BATTERY OR ALTERNATOR
BATTERY VOLTAGE IS LESS
THAN 12V
PARTIAL FUNCTION OF MODE
DOORS
NO MODE CHANGE AT ALL
VERIFY CONNECTIONS ON POWER LEAD, IGNITION
LEAD, AND BOTH WHITE GROUND WIRES.
WILL NOT TURN ON UNDER ANY
CONDITIONS
VERIFY BATTERY VOLTAGE IS GREATER THAN 10
VOLTS AND LESS THAN 16.
NOISE INTERFERENCE FROM EITHER IGNITION OR
ALTERNATOR.
WORKS WHEN ENGINE IS NOT
RUNNING, SHUTS OFF WHEN
ENGINE IS STARTED.
(TYPICALLY EARLY GEN 4, BUT
POSSIBLE ON ALL VERSIONS)
TAN WIRE IS ONLY USED ON SYSTEMS WITH
ENTIRE CONTROL PANEL SUPPLIED BY VINTAGE
AIR.
SYSTEM SHUTS OFF BLOWER AT 10V. POOR
CONNECTIONS OR WEAK BATTERY CAN CAUSE
SHUT DOWN AT UP TO 11V
TYPICALLY CAUSED BY EVAPORATOR HOUSING
INSTALLED IN A BIND IN THE VEHICLE. BE SURE
ALL MOUNTING LOCATIONS LINE UP AND DON'T
HAVE TO BE FORCED INTO POSITION.
IGNITION NOISE (RADIATED OR CONDUCTED) WILL
CAUSE THE SYSTEM TO SHUT DOWN DUE TO
HIGH VOLTAGE SPIKES. IF THIS IS SUSPECTED,
CHECK WITH A QUALITY OSCILISCOPE. SPIKES
GREATER THAN 16V WILL SHUT DOWN ECU.
INSTALL A RADIO CAPACITOR AT THE POSITIVE
POST OF THE IGNITION COIL (SEE RADIO
CAPACITOR INSTALLATION BULLETEN). A FAULTY
ALTERNATOR OR WORN OUT BATTERY CAN ALSO
RESULT IN THIS CONDITION. BATTERY MUST BE
IN GOOD CONDITION FOR ALTERNATOR
REGULATOR TO FUNCTION PROPERLY.
TROUBLE SHOOTING INFORMATION CONT.
1969-70 MUSTANG w/o AC GEN IV
7. ERATIC FUNCTIONS OF
BLOWER, MODE, TEMP, ETC.
6. BLOWER TURNS ON AND OFF
RAPIDLY
5. LOSS OF MODE DOOR
FUNCTION
4. SYSTEM WILL NOT TURN ON OR
RUNS INTERMITTENTLY
21
1969-70 MUSTANG w/o AC GEN IV
DRIVER SIDE LOUVER TEMPLATE
CUT ALONG
DOTTED LINE
CENTER
PUNC H
&
DRILL
2 3/4 HOLE
1969-70 MUSTANG w/o AC
DRIVER SIDE LOUVER
TEMPLATE
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 22 OF 26
22
PASSENGER SIDE LOUVER TEMPLATE
CU
DO T ALON
T
T
E
D LI G
NE
CENTER
PUNC H
&
DRILL
2 3/4 HOLE
1969-70 MUSTANG w/o AC
PASSENGER SIDE LOUVER
TEMPLATE
23
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 23 OF 26
1969-70 MUSTANG w/o AC GEN IV
CENTER LOUVER TEMPLATE
CUT ALONG
DOTTED LINE
CUT ALONG
DOTTED LINE
1969-70 MUSTANG w/o AC
CENTER LOUVER
TEMPLATE
24
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 24 OF 26
1969-70 MUSTANG w/o AC
FIREWALL COVER
HOLE TEMPLATE
(6) 3/16
HOLES
BLOWER
MOTOR
MOUNTING
HOLE
BLOWER
MOTOR
MOUNTING
HOLE
(4) ALIGNMENT HOLES
NG E
LO LIN
T A ED
CU TT
DO
BLOWER MOTOR
MOUNTING
HOLE
OEM HEATER
HOLE
BLOWER
MOTOR
MOUNTING
HOLE
THIS SIDE INSIDE OF CAR
CUT ALONG
DOTTED LINE
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 25 OF 26
25
1969-70 MUSTANG w/o AC GEN IV
EVAPORATOR KIT
551170
EVAPORATOR KIT PACKING LIST
No.
1.
2.
QTY.
1
1
PART No.
763069
781069
DESCRIPTION
69-70 MUSTANG EVAP. SUB CASE
1969-70 MUSTANG w/o AC ACC. KIT
CHECKED BY:
PACKED BY:
DATE:
1
69-70 MUSTANG
EVAP. SUB CASE
763069
2
F
A
N
ACCESSORY KIT
781069
DASH
COLD
FLR
DEF
HOT
NOTE: IMAGES MAY NOT DEPICT ACTUAL PARTS AND QUANTITIES.
REFER TO PACKING LIST FOR ACTUAL PARTS AND QUANTITIES
901271 REV A 2/11/08, 69-70 MUSTANG w/o AC GEN IV EVAP INSTR PG 26 OF 26
Download PDF