Advantech | PCM-3362 | User manual | Advantech PCM-3362 User manual

User Manual
PCM-3362
PC/104-plus SBC with
Intel® Atom™ N450, VGA, LCD,
LAN, USB2.0, SATA, and
on-board flash
Copyright
The documentation and the software included with this product are copyrighted 2009
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use.
Acknowledgements
AMI is a trademark of American Megatrends, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Corporation.
Atom, Pentium, Celeron, and MMX are registered trademarks of Intel Corporation.
Microsoft Windows® is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd. ESS is a trademark of ESS
Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
SMI is a trademark of Silicon Motion, Inc.
Creative is a trademark of Creative Technology LTD.
All other product names or trademarks are properties of their respective owners.
For more information on this and other Advantech products, please visit our websites
at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our support website at:
http://www.advantech.com/support
This manual is for the PCM-3362.
PCM-3362 User Manual
Part No. 2006336210
Edition 1
Printed in China
Dec. 2009
ii
Packing List
Before you begin installing your card, please make sure that the following materials
have been shipped:
„
1 x PCM-3362 SBC
„
1 x SATA data cable
(p/n: 1700071000)
„
1 x SATA power cable
(p/n: 1703150102)
„
1 x Keyboard/Mouse cable
(p/n: 1703060053)
„
1 x Y cable for KB/MS extension
(p/n: 1700060202)
„
1 x Ethernet RJ-45 Conn. conversion cable
(p/n: 1700017863)
„
1 x VGA cable
(p/n: 1700000898)
„
1 x USB cable (bracket type with two USB ports)
(p/n: 1703100260)
„
1 x RS-422/485 COM cable
(p/n: 1703040157)
„
1 x RS-232 COM cable
(p/n: 1701200220)
„
1 x ATX Power cable
(p/n: 1700002332)
„
1 x AT Power cable
(p/n: 1700003491)
„
1 x Startup manual
„
1 x CD-ROM (Manual, Driver, Utility)
If any of these items are missing or damaged, contact your distributor or sales representative immediately.
Model No.List
Description
PCM-3362N-S6A1E
Intel Atom N450 PC/104-Plus SBC, VGA, LVDS, LAN,
USB,SATA and on-board flash
Optional Accessory
1 x heatspreader
(p/n:1960047106T001)
Additional Information and Assistance
1.
2.
„
„
„
„
„
Visit the Advantech web site at www.advantech.com where you can find the latest information about the product.
Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
Product name and serial number
Description of your peripheral attachments
Description of your software (operating system, version, application software,
etc.)
A complete description of the problem
The exact wording of any error messages
Declaration of Conformity
This device complies with the requirements in part 15 of the FCC rules: Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
iii
PCM-3362 User Manual
2.
This device must accept any interference received, including interference that
may cause undesired operation
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Opera- thin of
this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the manflatterer. Discard used batteries according to the manufacturer's instructions.
PCM-3362 User Manual
iv
Contents
Chapter
1
General Information ............................1
1.1
1.2
1.3
Introduction ............................................................................................... 2
Features .................................................................................................... 2
Specifications ............................................................................................ 2
1.3.1 Standard PC/104-plus Biscuit SBC Functions .............................. 2
1.3.2 VGA/LVDS Interface ..................................................................... 3
1.3.3 Ethernet Interface ......................................................................... 3
1.3.4 OS support.................................................................................... 3
1.3.5 Mechanical and Environmental..................................................... 3
Board layout: dimensions.......................................................................... 4
Figure 1.1 Board layout: Dimensions (Component Side) ............ 4
Figure 1.2 Board layout: Dimensions (Solder Side)..................... 5
1.4
Chapter
2
Hardware Installation ..........................7
2.1
Jumpers .................................................................................................... 8
Table 2.1: Jumpers...................................................................... 8
Connectors................................................................................................ 8
Table 2.2: Connectors ................................................................. 8
Locating Connectors & block diagram ...................................................... 9
Figure 2.1 Connectors (component side) .................................... 9
Figure 2.2 Connectors (solder side) ............................................ 9
Figure 2.3 Block diagram........................................................... 10
Setting Jumpers ...................................................................................... 10
2.4.1 Clear CMOS (JP1) ...................................................................... 11
Table 2.3: Clear CMOS (JP1).................................................... 11
2.4.2 LVDS Panel Power Select (JP2)................................................. 11
Table 2.4: LVDS Panel Power Select (JP2) .............................. 11
2.4.3 COM3 RS422/RS485 Select (JP3) ............................................. 12
Table 2.5: COM3 RS422/RS485 Select (JP3)........................... 12
2.4.4 PCI I/O Voltage Select (JP4) ...................................................... 12
Table 2.6: PCI I/O Voltage Select (JP4) .................................... 12
Installing SODIMMs ................................................................................ 12
Flash ....................................................................................................... 12
High Definition Audio Interface (CN1) ..................................................... 13
VGA/LCD interface connections ............................................................. 13
2.8.1 CRT display connector (CN8) ..................................................... 13
2.8.2 LVDS connector (CN6) ............................................................... 13
2.8.3 Panel Inverter Power (CN7)........................................................ 13
USB connectors (CN9 & CN10) .............................................................. 13
Front Panel Connector (CN12) ............................................................... 13
Buzzer Connector (CN13)....................................................................... 14
SATA Connector (CN15)......................................................................... 14
COM port connector (CN16 & CN17)...................................................... 14
2.13.1 Serial Port RS-422/485 (CN17) .................................................. 14
Giga LAN Connector (CN18) .................................................................. 14
2.14.1 LAN LED Connector (CN19)....................................................... 14
Keyboard and PS/2 mouse connector (CN20)........................................ 14
GPIO Connector (CN21) ......................................................................... 15
ATX Power in connector (CN23)............................................................. 15
Power Connectors (CN24) ...................................................................... 15
I2C Bus connector (CN25) ...................................................................... 15
-12 V & -5 V power connector (CN26) ................................................... 15
Watchdog timer configuration ................................................................. 15
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
2.17
2.18
2.19
2.20
2.21
v
PCM-3362 User Manual
Chapter
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
PCM-3362 User Manual
AMI BIOS Setup................................. 17
Figure 3.1 Setup program initial screen..................................... 18
Entering Setup ........................................................................................ 18
Main Setup.............................................................................................. 18
Figure 3.2 Main setup screen .................................................... 19
3.2.1 System time / System date ......................................................... 19
Advanced BIOS Features Setup............................................................. 19
Figure 3.3 Advanced BIOS features setup screen .................... 20
3.3.1 CPU Configuration...................................................................... 20
Figure 3.4 CPU Configuration Setting ....................................... 20
3.3.2 IDE Configuration ....................................................................... 21
Figure 3.5 IDE Configuration ..................................................... 21
3.3.3 Super I/O Configuration .............................................................. 22
Figure 3.6 Super I/O Configuration............................................ 22
3.3.4 Hardware Health Configuration .................................................. 22
Figure 3.7 Hardware health configuration ................................. 22
3.3.5 ACPI Settings ............................................................................. 23
Figure 3.8 ACPI Settings ........................................................... 23
Figure 3.9 General ACPI Configuration..................................... 23
Figure 3.10Advanced ACPI Configuration.................................. 24
Figure 3.11Chipset ACPI Configuration ..................................... 24
3.3.6 AHCI Configuration..................................................................... 25
Figure 3.12Advanced ACPI Configuration.................................. 25
3.3.7 APM Configuration...................................................................... 26
Figure 3.13APM Configuration ................................................... 26
3.3.8 Event Log Configuration ............................................................. 27
Figure 3.14South Bridge ACPI Configuration............................. 27
3.3.9 MPS Configuration...................................................................... 27
Figure 3.15South Bridge ACPI Configuration............................. 27
3.3.10 Smbios Configuration ................................................................. 28
Figure 3.16South Bridge ACPI Configuration............................. 28
3.3.11 USB Configuration ...................................................................... 28
Figure 3.17South Bridge ACPI Configuration............................. 28
Figure 3.18USB Mass storage Device Configuration ................. 29
Advanced PCI/PnP Settings ................................................................... 29
Figure 3.19PCI/PNP Setup (top) ................................................ 30
Boot Settings........................................................................................... 31
Figure 3.20Boot Setup Utility...................................................... 31
3.5.1 Boot settings Configuration......................................................... 31
Figure 3.21Boot Setting Configuration ....................................... 31
Security Setup......................................................................................... 32
Figure 3.22Password Configuration ........................................... 32
Advanced Chipset Settings..................................................................... 33
Figure 3.23Advanced Chipset Settings ...................................... 33
3.7.1 North Bridge Chipset Configuration ............................................ 33
Figure 3.24North Bridge Configuration....................................... 33
Figure 3.25Video function configuration ..................................... 34
3.7.2 South Bridge Chipset Configuration ........................................... 34
Figure 3.26South Bridge Configuration ...................................... 34
Exit Option .............................................................................................. 35
Figure 3.27Exit Option................................................................ 35
3.8.1 Save Changes and Exit .............................................................. 35
3.8.2 Discard Changes and Exit .......................................................... 36
3.8.3 Load Optimal Defaults ................................................................ 36
3.8.4 Load Fail-Safe Defaults .............................................................. 36
vi
Chapter
4
Software Introduction & Installation ....37
4.1
4.2
S/W Introduction...................................................................................... 38
Driver Installation .................................................................................... 38
4.2.1 Windows XP professional ........................................................... 38
4.2.2 Other OS..................................................................................... 38
Value-Added Software Services ............................................................. 38
4.3.1 SUSI Introduction........................................................................ 38
4.3.2 Software APIs ............................................................................. 39
4.3.3 SUSI Utilities ............................................................................... 40
4.3.4 SUSI Installation ......................................................................... 40
4.3.5 SUSI Sample Programs.............................................................. 42
4.3
Chapter
5
Chipset Software Installation Utility.....49
5.1
5.2
5.3
Before You Begin .................................................................................... 50
Introduction ............................................................................................. 50
Windows XP/Vista/Win7 Driver Setup..................................................... 50
6
Integrated Graphic Device Setup .....51
6.1
6.2
Introduction ............................................................................................. 52
Windows XP/ Vista /Win7 Driver Setup................................................... 52
7
LAN Configuration.............................53
7.1
7.2
7.3
Introduction ............................................................................................. 54
Installation ............................................................................................... 54
Windows XP/ Vista /Win7 Driver Setup................................................... 54
Appendix A
Pin Assignments ...............................55
A.1
Jumper and Connector Tables................................................................ 56
Appendix B
System Assignments ........................65
B.1
System I/O Ports ..................................................................................... 66
Table B.1: System I/O ports....................................................... 66
1st MB Memory Map ............................................................................... 66
Table B.2: 1st MB memory map ................................................ 66
DMA channel assignments ..................................................................... 66
Table B.3: DMA channel assignments....................................... 66
Interrupt assignments.............................................................................. 67
Table B.4: Interrupt assignments ............................................... 67
Chapter
Chapter
B.2
B.3
B.4
Appendix C
Mechanical Drawings ........................69
C.1
Board Mechanical Drawings ................................................................... 70
Figure C.1 PCM-3362 Mechanical Drawing (Component Side). 70
Figure C.2 PCM-3362 Mechanical Drawing (Solder Side) ......... 71
Heatsink Mechanical Drawings ............................................................... 72
Figure C.3 PCM-3362N Heatsink Mechanical Drawing ............. 72
Figure C.4 PCM-3362Z/Z2 Heatsink Mech Dwg, wide temp...... 72
Optional Heat spreader Mechanical Drawings........................................ 73
Figure C.5 PCM-3362 optional Heatspreader Mech Drawing .... 73
C.2
C.3
vii
PCM-3362 User Manual
Appendix D
Watchdog Timer and GPIO sample
code.................................................... 75
D.1
D.2
Watchdog Timer sample code ................................................................ 76
GPIO sample code.................................................................................. 77
PCM-3362 User Manual
viii
Chapter
1
1
General Information
This chapter gives background
information on the PCM-3362.
Sections include:
„ Introduction
„ Features
„ Specifications
„ Board layout and dimensions
1.1 Introduction
The PCM-3362 is a fanless, low power, small size (96X90mm), performance PC/104plus SBC (Single Board Computer) geared to satisfy the needs for various industrial
computing equipment. PCM-3362 is ideal for communication, environment monitoring, factory automation, military, and medical applications that require flat panel support using digital displays with LVDS interfaces and single Ethernet ports.
For those who want superior performance for various low-power embedded applications, PCM-3362 uses an Intel® Atom™ N450 processor, supporting DDRII 667
SDRAM up to 2GB.
PCM-3362 has an integrated graphic core of Intel® Embedded Gen3.5+ graphic
technology with 224 MB shared memory. This feature makes PCM-3362 is capable
of handling complex and intense 2D/3D graphic processing, its VGA and LVDS dual
video outputs also make it suitable for applications requiring dual display or digital
panel display capabilities.
PCM-3362 offers convenient connector layout, easy assembly, multiple I/Os, and
includes a single 10/100/1000 Mbps Ethernet, four USB (Universal Serial Bus) 2.0,
one SATA2 interface, 8-bit general purpose Input/Output, two RS-232 serial ports
and one RS-422/485 serial port for easy system expansibility. PC/104-plus self-stacking rugged mechanical architecture and extended temperature operation makes it
ideal for outdoor applications in the military and transportation fields.
Supported operating systems include Windows 7, Windows XP, XP Embedded, Windows CE, and Linux. PCM-3362 also offers drivers and APIs for application development including I2C, GPIO, watchdog timer, hardware monitor, panel backlight on/off,
and brightness control.
1.2 Features
„
„
„
„
„
„
„
„
„
IIntel® Atom™ N450 Processor
Supports DDR2 667 memory
Supports 18-bit LVDS LCD interface
Supports 1 X SATA2 interface
Supports 2GB on-board flash
Supports 1 x 10/100/1000 Mbps Fast Ethernet
Supports four USB2.0 ports
Supports two serial RS-232 ports (COM1/2), one RS-422/485 port(COM3)
PC/104-plus expansion interface
1.3 Specifications
1.3.1 Standard PC/104-plus Biscuit SBC Functions
„
„
CPU: Intel® Atom™ N450 processor, up to 1.67 GHz
System Memory: supports Double Data Rate (DDR) DDR2 667 SDRAM up to
2GB
Note!
PCM-3362 cannot support DDR2 533 SDRAM.
PCM-3362 User Manual
2
1.3.2 VGA/LVDS Interface
„
„
„
Controller: Integrated graphic core of Embedded Gen3.5+ technology
VRAM: 224 MB shared system memory
Output Interfaces:
– VGA: Supports up to SXGA 1400 x 1060 @ 60Hz
– LVDS: Singe channel 18-bit LVDS up to WXGA 1366 x 768
– Dual Display: CRT + LVDS, support extended mode and clone mode
1.3.3 Ethernet Interface
„
Supports Single 10/100/1000 Mbps Ethernet networking
„
Controller: Intel® 82567V
1.3.4 OS support
This board supports Win7,Win XP, Win CE and Win XPe.
For further information about OS support in your PCM-3362, visit the following
Advantech web resource: www.advantech.com or please contact your technical support center.
1.3.5 Mechanical and Environmental
„
„
„
„
„
Dimensions: 96 x 90 mm (3.8" x 3.5") Mechanical Drawing (dxf file) is available.
Power Supply Type: AT/ATX
Power Requirement: +5 V ± 5%, +12 V ± 5% (Optional), (5 V only, 12 V
optional for PC104 add on card and LCD inverter)
Power Consumption: (Intel® Atom™ N450, 1GB DDRII 667)
– Power on Load: +5 V @ 2.28 A, +12 V @ 5mA
– Max load: +5 V @ 2.37 A, +12 V @ 7mA
– Idle mode: +5 V @ 2 A, +12 V @ 5mA
Power Consumption Conditions:
– Test software: Maxpower + 3DMark 2005
3
PCM-3362 User Manual
General Information
„
„
„
2nd Cache Memory: 512 KB on the processor
System Chipset: Intel® ICH8M
BIOS: AMI 16Mbit Flash BIOS
Watchdog timer: 255 levels timer interval
Expansion Interface: PC/104-Plus (ISA and PCI bus)
Battery: Lithium 3V/210 mAH
Power management: ACPI supported
Serial ATA: One Serial ATA2 interface, Speed up to 300MB/s
Flash: On board 2GB flash (IDE interface)
Serial ports: Two serial RS-232 ports (COM1/2), one RS-422/485 port(COM3)
Keyboard/mouse connector: Supports one standard PC/AT keyboard and a
PS/2 mouse
USB: Four USB 2.0 ports compliant universal serial bus ports
GPIO: 8 bit general purpose Input/Output
High Definition Audio: PCM-3362 can provide audio function with the optional
audio extension module PCA-AUDIO-HDA1E and specific audio cable.
Chapter 1
„
„
„
„
„
„
„
„
„
„
„
„
„
– Power on - Boot: Measure the maximum current value of between system
power on and boot-up to O.S.
– Max. load: Measure the maximum current value which system under maximum load (CPU: Top speed, RAM &Graphic: Full loading)
– Idle mode: Measure the current value when system in windows mode and
without running any program
Operating temperature: 0 ~ 60°C (32 ~ 140°F) (operation humidity: 40°C @
85% RH Non-Condensing)
Weight: 0.85 kg (reference weight of total package)
1.4 Board layout: dimensions
Figure 1.1 Board layout: Dimensions (Component Side)
PCM-3362 User Manual
4
Chapter 1
General Information
Figure 1.2 Board layout: Dimensions (Solder Side)
5
PCM-3362 User Manual
PCM-3362 User Manual
6
Chapter
2
2
Hardware Installation
This chapter explains the setup procedures of the PCM-3362 hardware, including
instructions on setting jumpers and connecting peripherals, switches and indicators.
Be sure to read all safety precautions before you begin the installation procedure.
2.1 Jumpers
The PCM-3362 has a number of jumpers that allow you to configure your system to
suit your application. The table below lists the functions of the various jumpers.
Table 2.1: Jumpers
JP1
CLEAR CMOS
JP2
LVDS Panel Power Select
JP3
COM3 RS422/RS485 Select
JP4
PCI I/O Voltage Select
2.2 Connectors
Onboard connectors link the PCM-3362 to external devices such as hard disk drives,
a keyboard, or floppy drives. The table below lists the function of each of the board's
connectors.
Table 2.2: Connectors
Label
Function
CN1
HD Audio Connector
CN4
SO-DIMM Connector
CN6
LVDS Connected
CN7
Panel Inverter Connector
CN8
VGA Connector
CN9
USB Port0/1 Connector
CN10
USB Port2/3 Connector
CN12
Front panel Connector
CN13
Buzzer Connector
CN15
SATA Connector
CN16
COM1~COM2 Connector
CN17
RS422/485 Connector
CN18
LAN Connector
CN19
LAN LED Connector
CN20
PS2 Keyboard/Mouse Connector
CN21
GPIO Connector
CN23
ATX Power In Connector
CN24
Power In Connector
CN25
I2C BUS connector
CN26
-12 V & -5 V power connector
P1
PC104-plus Connector
BH1
RTC Battery Connector
PCM-3362 User Manual
8
Chapter 2
2.3 Locating Connectors & block diagram
Hardware Installation
Figure 2.1 Connectors (component side)
Figure 2.2 Connectors (solder side)
9
PCM-3362 User Manual
Figure 2.3 Block diagram
2.4 Setting Jumpers
You may configure your card to match the needs of your application by setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two
metal pins and a small metal clip (often protected by a plastic cover) that slides over
the pins to connect them. To “close” a jumper, you connect the pins with the clip. To
“open” a jumper, you remove the clip. Sometimes a jumper will have three pins,
labeled 1, 2 and 3. In this case you would connect either pins 1 and 2, or 2 and 3.
RSHQ
PCM-3362 User Manual
FORVHG
10
FORVHG
Open
Closed
Closed 2-3
2.4.1 Clear CMOS (JP1)
The PCM-3362 single board computer contains a jumper that can erase CMOS data
and reset the system BIOS information. Normally this jumper should be set with pins
1-2 closed. If you want to reset the CMOS data, set CMOS1 to 2-3 closed for just a
few seconds, and then move the jumper back to 1-2 closed. This procedure will reset
the CMOS to its default setting.
Warning! To avoid damaging the computer, always turn off the power supply
before clearing CMOS.
Table 2.3: Clear CMOS (JP1)
Setting
Function
1-2
Normal (default)
2-3
Clear CMOS
2.4.2 LVDS Panel Power Select (JP2)
Table 2.4: LVDS Panel Power Select (JP2)
Setting
Function
1-2
5V
2-3
3.3 V (default)
11
PCM-3362 User Manual
Hardware Installation
A pair of needle-nose pliers may be helpful when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact your
local distributor or sales representative before you make any changes. Generally, you
simply need a standard cable to make most connections.
Chapter 2
The jumper settings are schematically depicted in this manual as follows:
2.4.3 COM3 RS422/RS485 Select (JP3)
Table 2.5: COM3 RS422/RS485 Select (JP3)
Setting
Function
1-2
RS-485 (default)
2-3
RS-422
2.4.4 PCI I/O Voltage Select (JP4)
The PCI Host board will always determine the PCI signaling level on the bus by setting all VI/O pins to either 3.3 V or 5 V. If VI/0 is set to 3.3 V, then the system will use
3.3 V I/O signaling, likewise, if VI/O is set to 5 V, then the system will use 5 V I/O signaling. Some PCI host modules may only allow one of the options, while others may
provide a jumper to allow the user to select the signaling level. Once the signaling
level is selected, the remaining boards in the system must use that signaling level.
Table 2.6: PCI I/O Voltage Select (JP4)
Setting
Function
1-2
5 V (default)
2-3
3.3 V
2.5 Installing SODIMMs
The procedures for installing SODIMMs are described below. Please follow these
steps carefully. You can install SDRAM memory modules using 200-pin SODIMMs
(Small Outline Dual In-line Memory Modules).
1. Ensure that all power supplies to the system are switched off.
2. Tilt the SODIMM card just above the board and slide it into the housing card
slot.
3. Push the module into the socket until the module gently snaps in. There should
only be a slight insertion force to engage the module into the contacts. Make
sure that the module and the housing are aligned and locked in place.
2.6 Flash
The board provides onboard NAND Flash memory to replace CF socket. NANDriveTM integrated circuits (IC) are high-performance, fully-integrated, embedded flash
solid state drives. They combine an integrated ATA Controller in a multi-chip package. These products are ideal for industrial grade solid state mass storage applications offering new and expanded functionality while enabling cost effective designs.
PCM-3362 User Manual
12
2.7 High Definition Audio Interface (CN1)
2.8 VGA/LCD interface connections
The PCM-3362’s VGA interface can drive conventional CRT displays and is capable
of driving a wide range of LVDS flat panel displays. The board has two connectors to
support these displays: one for standard CRT VGA monitors, one for LVDS type LCD
panels.
2.8.1 CRT display connector (CN8)
CN8 is a 12-pin, dual-inline header used for conventional CRT displays. A simple
one-to-one adapter can be used to match CN8 to a standard 15-pin D-SUB connector commonly used for VGA. Users can drive a standard progressive scan analog
monitor with pixel resolution up to SXGA 1400 x 1060 @ 60Hz. Pin assignments for
CRT display connector CN8 are detailed in Appendix A.
2.8.2 LVDS connector (CN6)
The PCM-3362 uses the Intel Atom N450 that supports single -channel 18-bit LVDS
panel up to WXGA 1366 x 768 UXGA panel resolution.
2.8.3 Panel Inverter Power (CN7)
The LCD inverter is connected to CN7 via a 5-pin connector to provide +5 V/+12 V
power to the LCD display. JP2 provides inverter voltage selection function, closing
Pin 1, 2 is for 5 V power input inverter; closing Pin 2, 3 is for 3.3 V power input
inverter.
2.9 USB connectors (CN9 & CN10)
The board provides up to four USB (Universal Serial Bus) ports using Plug and Play.
The USB interfaces comply with High Speed USB specification Rev. 2.0 which supports 480 Mbps transfer rate, and are fuse protected.
The USB interface is accessed through two 5 x 2-pin pin header connectors. You will
need an adapter cable if you use a standard USB connector. The adapter cable has a
5 x 2-pin connector on one end and a USB connector on the other. The USB interfaces can be disabled in the system BIOS setup.
2.10 Front Panel Connector (CN12)
You may want to install external switches to monitor and control the PCM-3362.
These features are optional: install them only if you need them.
Power Button(Pin1 & Pin2)
PCM-3362 supports power on/off button.
13
PCM-3362 User Manual
Hardware Installation
The PCM-3362 provides high definition audio interface. It can support high definition
audio stereo by customized audio module that has codec onboard or by Advantech’s
PCA-AUDIO-HDA1E module through specific cable.
Chapter 2
PCM-3362 supports 2GB industrial grade NAND NANDriveTM IC and up to 4GB for
option. Flash endurance is about 100 Million write cycles. Data Retention is about 10
Years. PCM-3362’s NANDriveTM IC supports up to Ultra DMA Mode-4 and endures
in wide temperature range of -40°C to +85°C for industrial operation.
Reset (Pin3 & Pin4)
If you install a reset switch, it should be an open single pole switch.
Momentarily pressing the switch will activate a reset.
POWER LED (Pin5 & Pin6)
POWER LED indicator would light when the power is on.
HDD LED (Pin7 & Pin8)
The HDD LED indicator for hard disk access is an active low signal.
2.11 Buzzer Connector (CN13)
PCM-3362 provides one buzzer connector to connect buzzer for alert function.
Buzzer, Advantech’s P/N:1750005282, can be selected to install on board.
2.12 SATA Connector (CN15)
In addition to on board 2GB flash, PCM-3362 features one high performance serial
ATA interfaces (up to 300 MB/s) that eases cabling to hard drives with thin and long
cables while your application need more large storage capacity.
2.13 COM port connector (CN16 & CN17)
The board provides three serial ports: two serial RS-232 ports in one 20 pin connector (CN16:COM1/2), and one serial port RS422/485 in 4 pin connector(CN17:
COM3).
It provides connections for serial devices or a communication network. You can find
the pin assignments for the COM port connector in Appendix.
2.13.1 Serial Port RS-422/485 (CN17)
COM3 (CN17) can be configured to operate in RS-422 or RS-485 mode by JP3.
2.14 Giga LAN Connector (CN18)
PCM-3362 uses the Intel? 82567V Gigabit LAN chips are linked to dedicated PCIe x1
lanes. PCM-3362 provide high throughputs for heavy loading networking environment. LAN connections are made via two internal 10-pin box header.
2.14.1 LAN LED Connector (CN19)
PCM-3362 provides an external LAN LED Pin header for connecting to the front side
of the chassis. With this convenient design users may know whether the LAN port is
acting or not easily. Refer to Appendix for detailed information on the pin assignments.
2.15 Keyboard and PS/2 mouse connector (CN20)
The board provides a keyboard connector that supports both a keyboard and a PS/2
style mouse. In most cases, especially in embedded applications, a keyboard is not
used. If the keyboard is not present, the standard PC/AT BIOS will report an error or
fail during power-on self-test (POST) after a reset. The PCM 3362's BIOS standard
setup menu allows you to select "All, But Keyboard" under the "Halt On" selection.
This allows no-keyboard operation in embedded system applications, without the
system halting under POST.
PCM-3362 User Manual
14
The board supports 8-bit GPIO through GPIO connector. The 8 digital inputs and outputs can be programmed to read or control devices, with each input or output
defined.
2.17 ATX Power in connector (CN23)
Caution! Important Make sure that the ATX power supply can take at least a
10mA load on the 5 V standby lead (5VSB). If not, you may have difficulty powering on your system.
2.18 Power Connectors (CN24)
Supplies main power +5 V to the PCM-3362, and to devices that require +12 V.
2.19 I2C Bus connector (CN25)
PCM-3362 provides I2C Bus connector for customer connection to I2C protocol
embedded device.
Advantech also provide I2C API allowing a developer to interface with an embedded
system environment and transfer serial messages using the I2C protocols, allowing
multiple simultaneous device control.
2.20 -12 V & -5 V power connector (CN26)
The PCM-3362 is equipped with a Negative Power Input connector providing -12 V &
-5 V power if your applications happen to need it.
2.21 Watchdog timer configuration
An onboard watchdog timer reduces the chance of disruptions which EMP (electro
magnetic pulse) interference can cause. This is an invaluable protective device for
standalone or unmanned applications. Setup involves one jumper and running the
control software (refer to Appendix).
15
PCM-3362 User Manual
Hardware Installation
The PCM-3362 can support an advanced soft power switch function, if an ATX power
supply is used. please follow below instruction to enable ATX functions.
1. Plug ATX power cable (1700002332) into CN24.
2. Connect the 3-pin plug of this power cable to CN23 (ATX Power in connector).
3. Connect the power on/off button cable of the chassis to CN12 (front panel connector) pin1-2.
Chapter 2
2.16 GPIO Connector (CN21)
PCM-3362 User Manual
16
Chapter
3
AMI BIOS Setup
3
AMIBIOS has been integrated into many motherboards for over a decade. With the
AMIBIOS Setup program, you can modify BIOS settings and control the various system features. This chapter describes the basic navigation of the PCM-3362 BIOS
setup screens.
Figure 3.1 Setup program initial screen
AMI’s BIOS ROM has a built-in Setup program that allows users to modify the basic
system configuration. This information is stored in battery-backed CMOS so it retains
the Setup information when the power is turned off.
3.1 Entering Setup
Turn on the computer and check for the “patch” code. If there is a number assigned to
the patch code, it means that the BIOS supports your CPU. If there is no number
assigned to the patch code, please contact an Advantech application engineer to
obtain an up-to-date patch code file. This will ensure that your CPU’s system status is
valid. After ensuring that you have a number assigned to the patch code, press
<DEL> and you will immediately be allowed to enter Setup.
3.2 Main Setup
When you first enter the BIOS Setup Utility, you will encounter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab. There are
two Main Setup options. They are described in this section. The Main BIOS Setup
screen is shown below.
PCM-3362 User Manual
18
Chapter 3
3.2.1 System time / System date
Use this option to change the system time and date. Highlight System Time or System Date using the <Arrow> keys. Enter new values through the keyboard. Press the
<Tab> key or the <Arrow> keys to move between fields. The date must be entered in
MM/DD/YY format. The time must be entered in HH:MM:SS format.
3.3 Advanced BIOS Features Setup
Select the Advanced tab from the PCM-3362 setup screen to enter the Advanced
BIOS Setup screen. You can select any of the items in the left frame of the screen,
such as CPU Configuration, to go to the sub menu for that item. You can display an
Advanced BIOS Setup option by highlighting it using the <Arrow> keys. All Advanced
BIOS Setup options are described in this section. The Advanced BIOS Setup
screens is shown below. The sub menus are described on the following pages.
19
PCM-3362 User Manual
AMI BIOS Setup
Figure 3.2 Main setup screen
The Main BIOS setup screen has two main frames. The left frame displays all the
options that can be configured. Grayed-out options cannot be configured; options in
blue can. The right frame displays the key legend.
Above the key legend is an area reserved for a text message. When an option is
selected in the left frame, it is highlighted in white. Often a text message will accompany it.
Figure 3.3 Advanced BIOS features setup screen
3.3.1 CPU Configuration
Figure 3.4 CPU Configuration Setting
Max CPUID Value Limit
This item allows you to limit CPUID maximum value.
Execute-Disable Bit Capability
This item allows you to enable or disable the No-Execution page protection technology.
Hyper Threading Technology
This item allows you to enable or disable Intel® Hyper Threading technology.
Intel® SpeedStepTM tech
When set to disabled, the CPU runs at its default speed, when set to enabled, the
CPU speed is controlled by the operating system.
PCM-3362 User Manual
20
3.3.2 IDE Configuration
Chapter 3
Intel® C-STATE tech
This item allows the CPU to save more power under idle mode.
Enhanced C-States
CPU idle set to enhanced C-States, disabled by Intel® C-STATE tech item.
AMI BIOS Setup
Figure 3.5 IDE Configuration
ATA/IDE Configuration
This item allows you to select Disabled / Compatible / Enhanced.
Legacy IDE Channels
When set to Enhanced mode you can select IDE or AHCI mode. When select Compatible mode you can select SATA only / SATA pri, PATA sec or PATA only.
Primary/Secondary/Third IDE Master
BIOS auto detects the presence of IDE device, and displays the status of auto detection of IDE device.
„ Type: Select the type of SATA driver.[Not Installed][Auto][CD/DVD][ARMD]
„ LBA/Large Mode: Enables or Disables the LBA mode.
„ Block (Multi-Sector Transfer): Enables or disables data multi-sectors transfers.
„ PIO Mode: Select the PIO mode.
„ DMA Mode: Select the DMA mode.
„ S.M.A.R.T.: Select the smart monitoring, analysis, and reporting technology.
„ 32Bit Data Transfer: Enables or disables 32-bit data transfer.
Hard Disk Write Protect
Disable/Enable device write protection. This will be effective only if device is
accessed through BIOS.
IDE Detect Time Out (Sec)
This item allows you to select the time out value for detecting ATA/ATAPI device(s).
21
PCM-3362 User Manual
3.3.3 Super I/O Configuration
Figure 3.6 Super I/O Configuration
Serial Port1 / Port2 / Port3 address
This item allows you to select serial port1 ~ port3 of base addresses.
Serial Port1 / Port2 / Port3 IRQ
This item allows you to select serial port1 ~ port3 of IRQ.
Auto Direction Control Sel
This item allows you to enable or disable auto flow control function.
3.3.4 Hardware Health Configuration
Figure 3.7 Hardware health configuration
H/W Health Function
This item allows you to control H/W monitor of showing.
PCM-3362 User Manual
22
Chapter 3
Temperature & Voltage show
CPU/System Temperature
Vcore / +3.3Vin / +5Vin / +12Vin / VBAT
3.3.5 ACPI Settings
AMI BIOS Setup
Figure 3.8 ACPI Settings
3.3.5.1 General ACPI Configuration
Figure 3.9 General ACPI Configuration
Suspend mode
Select the ACPI state used for system suspend.
Report Video on S3 Resume
This item allows you to invoke VA BIOS POST on S3/STR resume.
23
PCM-3362 User Manual
3.3.5.2 Advanced ACPI Configuration
Figure 3.10 Advanced ACPI Configuration
ACPI Version Features
This item allows you to enable RSDP pointers to 64-bit fixed system description
tables.
ACPI APIC support
Include APIC table pointer to RSDT pointer list.
AMI OEMB table
Include OEMB table pointer to R(x)SDT pointer lists.
Headless mode
Enable / Disable Headless operation mode through ACPI.
3.3.5.3 Chipset ACPI Configuration
Figure 3.11 Chipset ACPI Configuration
PCM-3362 User Manual
24
Chapter 3
Energy Lake Feature
Allows you to configure Intel's Energy Lake power management technology.
APIC ACPI SCI IRQ
Enable/Disable APIC ACPI SCI IRQ.
USB Device Wakeup From S3/S4
Enable/Disable USB Device Wakeup from S3/S4.
High Performance Event Timer
Enable/Disable High performance Event timer.
AMI BIOS Setup
3.3.6 AHCI Configuration
Figure 3.12 Advanced ACPI Configuration
AHCI Ports0
While entering setup, BIOS auto detects the presence of IDE devices. This displays
the status of auto detection of IDE device.
25
PCM-3362 User Manual
3.3.7 APM Configuration
Figure 3.13 APM Configuration
Power Management/APM
Enable or disable APM.
Power Button Mode
Power on, off, or enter suspend mode when the power button is pressed. The following options are also available.
Restore on AC power Loss
Use this to set up the system response after a power failure. The "Off" setting keeps
the system powered off after power failure, the "On" setting boots up the system after
failure, and the "Last State" returns the system to the status just before power failure.
Video Power Down Mode
Power down video in suspend or standby mode.
Hard Disk Power Down Mode
Power down Hard Disk in suspend or standby mode.
Standby Time Out
Go into standby in the specified time.
Suspend Time Out
Go into Suspend in the specified time.
Resume On Ring
Enable / Disable RI to generate a wake event.
Resume On PME#
Enable / Disable PME to generate a wake event.
Resume On RTC Alarm
Enable / Disable RTC to generate a wake event.
PCM-3362 User Manual
26
Chapter 3
3.3.8 Event Log Configuration
View Event Log
View all unread events on the event Log.
Mark all events as read
Mark all unread events as read.
Clear Event Log
Discard all events in the event Log.
3.3.9 MPS Configuration
Figure 3.15 South Bridge ACPI Configuration
MPS Revision
This item allows you to select MPS reversion.
27
PCM-3362 User Manual
AMI BIOS Setup
Figure 3.14 South Bridge ACPI Configuration
3.3.10 Smbios Configuration
Figure 3.16 South Bridge ACPI Configuration
Smbios Smi Support
SMBIOS SMI wrapper support for PnP function 50h-54h.
3.3.11 USB Configuration
Figure 3.17 South Bridge ACPI Configuration
Legacy USB Support
Enables support for legacy USB. Auto option disables legacy support if no USB
devices are connected.
USB 2.0 Controller Mode
This item allows you to select HiSpeed(480Mbps) or FullSpeed (12Mpbs).
PCM-3362 User Manual
28
3.3.11.1 USB Mass Storage Device Configuration
Chapter 3
BIOS EHCI Hand-Off
This is a workaround for OSes without EHCI hand-off support. The EHCI ownership
change should claim by EHCI driver.
Hotplug USB FDD Support
A dummy FDD device is created that will be associated with the hotplugged FDD
later. Auto option creates this dummy device only if there is no USB FDD present.
AMI BIOS Setup
Figure 3.18 USB Mass storage Device Configuration
USB Mass Storage Reset Delay
Number of sends POST wait for the USB mass storage device after start unit command.
Emulation Type
If Auto, USB devices less than 530MB will be emulated as Floppy and remaining as
hard drive. Force FDD option can be used to force a FDD formatted drive to boot as
FDD (Ex. ZIP drive).
3.4 Advanced PCI/PnP Settings
Select the PCI/PnP tab from the PCM-3362 setup screen to enter the Plug and Play
BIOS Setup screen. You can display a Plug and Play BIOS Setup option by highlighting it using the <Arrow> keys. All Plug and Play BIOS Setup options are described in
this section. The Plug and Play BIOS Setup screen is shown below.
29
PCM-3362 User Manual
Figure 3.19 PCI/PNP Setup (top)
Clear NVRAM
Set this value to force the BIOS to clear the Non-Volatile Random Access Memory
(NVRAM).The Optimal and Fail-Safe default setting is No.
Plug & Play O/S
When set to No, BIOS configures all the device in the system. When set to Yes and if
you install a Plug and Play operating system, the operating system configures the
Plug and Play device not required for boot.
PCI Latency Timer
Value in units of PCI clocks for PCI device latency timer register.
Allocate IRQ to PCI VGA
When set to Yes will assigns IRQ to PCI VGA card if card requests IRQ. When set to
No will not assign IRQ to PCI VGA card even if card requests an IRQ.
Palette Snooping
This item is designed to solve problems caused by some non-standard VGA card.
PCI IDE BusMaster
When set to enabled BIOS uses PCI busmastering for reading/writing to IDE drives.
OffBoard PCI/ISA IDE Card
Some PCI IDE cards may require this to be set to the PCI slot number that is holding
the card. When set to Auto will works for most PCI IDE cards.
IRQ3 / 4 / 5 / 7 / 9 / 10 /11
This item allows you respectively assign an interruptive type for IRQ-3, 4, 5, 7, 9, 10,
11.
DMA Channel0 / 1 / 3 / 5 / 6 / 7
When set to Available will specified DMA is available to be used by PCI/PnP devices.
When set to Reserved will specified DMA will Reserved for use by legacy ISA
devices.
Reserved Memory Size
This item allows you to reserved size of memory block for legacy ISA device.
PCM-3362 User Manual
30
Chapter 3
3.5 Boot Settings
AMI BIOS Setup
Figure 3.20 Boot Setup Utility
3.5.1 Boot settings Configuration
Figure 3.21 Boot Setting Configuration
Quick Boot
This item allows BIOS to skip certain tests while booting. This will decrease the time
needed to boot the system.
Quiet Boot
If this option is set to Disabled, the BIOS displays normal POST messages. If
Enabled, an OEM Logo is shown instead of POST messages.
AddOn ROM Display Mode
Set display mode for option ROM.
31
PCM-3362 User Manual
Bootup Num-Lock
Select the Power-on state for Numlock.
PS/2 Mouse Support
Select support for PS/2 Mouse.
Wait For ‘F1’ If Error
Wait for the F1 key to be pressed if an error occurs.
Hit ‘DEL’ Message Display
Displays “Press DEL to run Setup” in POST.
Interrupt 19 Capture
This item allows option ROMs to trap interrupt 19.
Bootsafe function
This item allows you to enables or disables bootsafe function.
3.6 Security Setup
Figure 3.22 Password Configuration
Select Security Setup from the PCM-3362 Setup main BIOS setup menu. All Security
Setup options, such as password protection and virus protection are described in this
section. To access the sub menu for the following items, select the item and press
<Enter>:
Change Supervisor / User Password
Boot sector Virus protection: The boot sector virus protection will warn if any program tries to write to the boot sector.
PCM-3362 User Manual
32
Chapter 3
3.7 Advanced Chipset Settings
3.7.1 North Bridge Chipset Configuration
Figure 3.24 North Bridge Configuration
DRAM Frequency
This item allows you to manually changed DRAM frequency.
Configure DRAM Timing by SPD
This item allows you to enables or disables detect by DRAM SPD.
Memory Hole
This item allows you to free 15MB-16MB of memory size for some ISA devices.
Internal Graphics Mode Select: Select the amount of system memory used by the
Internal graphics device.
33
PCM-3362 User Manual
AMI BIOS Setup
Figure 3.23 Advanced Chipset Settings
Figure 3.25 Video function configuration
DVMT Mode Select
Displays the active system memory mode.
DVMT/FIXED Memory
Specify the amount of DVMT / FIXED system memory to allocate for video memory.
Boot Display Device
Select boot display device at post stage.
Flat Panel Type
This item allows you to select which panel resolution you wants.
Spread Spectrum Clock
This item allows you to enables or disables spread spectrum clock.
3.7.2 South Bridge Chipset Configuration
Figure 3.26 South Bridge Configuration
PCM-3362 User Manual
34
Chapter 3
USB Functions
Disabled, 2 USB Ports, or 4 USB Ports.
USB 2.0 Controller
Enables or disables the USB 2.0 controller.
GbE controller
Enables or disables the GbE controller.
GbE LAN Boot
Enables or disables GbE LAN boot.
GbE Wake Up From S5
Enables or disables GbE LAN wake up from S5 function.
HDA Controller
Enables or disables the HDA controller.
SMBUS Controller
Enables or disables the SMBUS controller.
SLP_S4# Min. Assertion Width
This item allows you to set a delay of sorts.
AMI BIOS Setup
3.8 Exit Option
Figure 3.27 Exit Option
3.8.1 Save Changes and Exit
When you have completed system configuration, select this option to save your
changes, exit BIOS setup and reboot the computer so the new system configuration
parameters can take effect.
1. Select Exit Saving Changes from the Exit menu and press <Enter>.
The following message appears: Save Configuration Changes and Exit Now? [Ok]
[Cancel]
2. Select Ok or cancel.
35
PCM-3362 User Manual
3.8.2 Discard Changes and Exit
Select this option to quit Setup without making any permanent changes to the system
configuration.
1. Select Exit Discarding Changes from the Exit menu and press <Enter>. The following message appears: Discard Changes and Exit Setup Now? [Ok] [Cancel]
2. Select Ok to discard changes and exit. Discard Changes
3. Select Discard Changes from the Exit menu and press <Enter>.
3.8.3 Load Optimal Defaults
The PCM-3362 automatically configures all setup items to optimal settings when you
select this option. Optimal Defaults are designed for maximum system performance,
but may not work best for all computer applications. In particular, do not use the Optimal Defaults if your computer is experiencing system configuration problems. Select
Load Optimal Defaults from the Exit menu and press <Enter>.
3.8.4 Load Fail-Safe Defaults
The PCM-3362 automatically configures all setup options to fail-safe settings when
you select this option. Fail-Safe Defaults are designed for maximum system stability,
but not maximum performance. Select Fail-Safe Defaults if your computer is experiencing system configuration problems.
1. Select Load Fail-Safe Defaults from the Exit menu and press <Enter>. The following message appears: Load Fail-Safe Defaults? [OK] [Cancel]
2. Select OK to load Fail-Safe defaults.
PCM-3362 User Manual
36
Chapter
4
4
Software Introduction
& Installation
4.1 S/W Introduction
The mission of Advantech Embedded Software Services is to "Enhance quality of life
with Advantech platforms and Microsoft Windows® embedded technology." We
enable Windows® Embedded software products on Advantech platforms to more
effectively support the embedded computing community. Customers are freed from
the hassle of dealing with multiple vendors (Hardware suppliers, System integrators,
Embedded OS distributor) for projects. Our goal is to make Windows® Embedded
Software solutions easily and widely available to the embedded computing community.
4.2 Driver Installation
4.2.1 Windows XP professional
To install the drivers for Windows XP Professional, insert the CD into the CD-Rom, it
will auto-detect the hardware platform and then pop up with the “Embedded Computing Install Wizard” box; just select the drivers that you want to install then click “Install
All Selected Drivers”. Follow the Driver Setup Wizard instructions; click "Next" to
complete the installation.
4.2.2 Other OS
To install the drivers for Other Windows OS or Linux, please browse the CD to run the
setup file under each chipset folder on the CD-ROM.
4.3 Value-Added Software Services
4.3.1 SUSI Introduction
To make hardware easier and convenient to access for programmers, Advantech has
released a suite of API (Application Programming Interface) in the form of a program
library. The program Library is called Secured and Unified Smart Interface or SUSI
for short.
In modern operating systems, user space applications cannot access hardware
directly. Drivers are required to access hardware. User space applications access
hardware through drivers. Different operating systems usually define different interface for drivers. This means that user space applications call different functions for
hardware access in different operating systems. To provide a uniform interface for
accessing hardware, an abstraction layer is built on top of the drivers and SUSI is
such an abstraction layer. SUSI provides a uniform API for application programmers
to access the hardware functions in different Operating Systems and on different
Advantech hardware platforms.
Application programmers can invoke the functions exported by SUSI instead of calling the drivers directly. The benefit of using SUSI is portability. The same set of API is
defined for different Advantech hardware platforms. Also, the same set of API is
implemented in different Operating Systems including Windows XP and Windows
CE. This user’s manual describes some sample programs and the API in SUSI. The
hardware functions currently supported by SUSI can be grouped into a few categories including Watchdog, I2C, SMBus, GPIO, and VGA control. Each category of API
in SUSI is briefly described below.
PCM-3362 User Manual
38
PCM-3362 supports software APIs including GPIO, I2C, backlight on/off, Brightness
control, watchdog, Hardware Monitor, and Power Saving.
4.3.2.1 The GPIO API
General Purpose Input/Output is a flexible parallel interface that allows a variety of
custom connections. It allows users to monitor the level of signal input or set the output status to switch on/off a device. Our API also provides Programmable GPIO,
which allows developers to dynamically set the GPIO input or output status.
I2C is a bi-directional two-wire bus that was developed by Philips for use in their televisions in the 1980s and nowadays is used in various types of embedded systems.
The strict timing requirements defined in the I2C protocol has been taken care of by
SUSI. Instead of asking application programmers to figure out the strict timing
requirements in the I2C protocol, the I2C API in SUSI can be used to control I2C
devices by invoking other function calls. SUSI provides a consistent programming
interface for different Advantech boards. That means user programs using SUSI are
portable among different Advantech boards as long as the boards and SUSI provide
the required functionalities. Overall product development times can be greatly
reduced using SUSI.
4.3.2.3 The Display Control API
There are two kinds of VGA control APIs, backlight on/off control and brightness control. Backlight on/off control allows a developer to turn on or off the backlight, and to
control brightness smoothly.
1. Brightness Control
– The Brightness Control API allows a developer to interface with an embedded device to easily control brightness.
2. Backlight Control
– The Backlight API allows a developer to control the backlight (screen) on/off
in an embedded device.
4.3.2.4 The Watchdog API
A watchdog timer (abbreviated as WDT) is a hardware device which triggers an
action, e.g. rebooting the system, if the system does not reset the timer within a specific period of time. The WDT API in SUSI provides developers with functions such as
starting the timer, resetting the timer, and setting the timeout value if the hardware
requires customized timeout values.
4.3.2.5 The Hardware Monitor API
The hardware monitor (abbreviated as HWM) is a system health supervision capability achieved by placing certain I/O chips along with sensors for inspecting the target
of interests for certain condition indexes, such as fan speed, temperature and voltage
etc.
However, due to the inaccuracy among many commercially available hardware monitoring chips, Advantech has developed a unique scheme for hardware monitoring achieved by using a dedicated micro-processor with algorithms specifically designed
for providing accurate, real-time and reliable data content; helping protect your system in a more reliable manner.
4.3.2.6 The Power Saving API
1. CPU Speed
39
PCM-3362 User Manual
Software Introduction & Installation
4.3.2.2 The I2C API
Chapter 4
4.3.2 Software APIs
2.
– Make use of Intel SpeedStep technology to reduce power consumption. The
system will automatically adjust the CPU Speed depending on system loading.
System Throttling
– Refers to a series of methods for reducing power consumption in computers
by lowering the clock frequency. APIs allow the user to lower the clock from
87.5% to 12.5%.
4.3.3 SUSI Utilities
PCM-3362 supports software Utility including Embedded Security ID, Monitoring utility, eSOS.
4.3.3.1 Embedded Security ID
The embedded application is the most important property of a system integrator. It
contains valuable intellectual property, design knowledge and innovation, but it is
easily copied! The Embedded Security ID utility provides reliable security functions
for customers to secure their application data within embedded BIOS.
4.3.3.2 Monitoring utility
The Monitoring utility allows the customer to monitor system health, including voltage, CPU and system temperature and fan speed. These items are important to a
device; if critical errors happen and are not solved immediately, permanent damage
may be caused.
4.3.3.3 eSOS
The eSOS is a small OS stored in BIOS ROM. It will boot up in case of a main OS
crash. It will diagnose the hardware status, and then send an e-mail to a designated
administrator. The eSOS also provides remote connection: Telnet server and FTP
server, allowing the administrator to rescue the system.
Note!
eSOS Utility support on PCM-3362 is required to have BIOS modification.
4.3.4 SUSI Installation
SUSI supports many different operating systems. Each subsection below describes
how to install SUSI and related software on a specific operating system. Please refer
to the subsection matching your operating system.
4.3.4.1 Windows XP
In windows XP, you can install the library, drivers and demo programs onto the platform easily using the installation tool--The SUSI Library Installer. After the installer
has executed, the SUSI Library and related files for Windows XP can be found in the
target installation directory. The files are listed in the following table.
Directory
Contents
\Library
„
Susi.lib
Library for developing the applications on Windows XP.
„
Susi.dll
Dynamic library for SUSI on Windows XP.
PCM-3362 User Manual
40
„
SusiDemo.EXE
Demo program on Windows XP.
„
Susi.dll
Dynamic library for SUSI on Windows XP.
\Demo\SRC
Source code of the demo program on Windows XP.
The following section illustrates the installation process.
The version of the SUSI Library Installer shown on each screen shot
below depends on your own particular version.
1. Extract Susi.zip.
2. Double-click the "Setup.exe" file.
The installer searches for a previous installation of the SUSI Library. If it locates one,
a screen shot opens asking whether you want to modify, repair or remove the software. If a previous version is located, please see the section of [Maintenance Setup].
If it is not located, the following screen shot opens. Click Next.
4.3.4.2 Windows CE
In windows CE, there are three ways to install the SUSI Library, you can install it
manually or use Advantech CE-Builder to install the library or just copy the programs
and the library onto a compact flash card.
Express Installation:
You can use Advantech CE-Builder to load the library into the image.
„ First, you click the My Component tab.
„ In this tab, you click Add New Category button to add a new category, e.g. the
SUSI Library.
„ Then you can add a new file in this category, and upload the SUSI.dll for this
category.
„ After these steps, you can select the SUSI Library category you created for
every project.
Manual Installation:
You can add the SUSI Library into the image by editing any bib file.
First you open project.bib in the platform builder.
„ Add this line to the MODULES section of project.bib
Susi.dll $(_FLATRELEASEDIR)\Susi.dll NK SH
„ If you want to run the window-based demo, add following line:
SusiTest.exe $(_FLATRELEASEDIR)\SusiTest.exe
„ If you want to run the console-based demo, add following lines:
Watchdog.exe $(_FLATRELEASEDIR)\Watchdog.exe NK S
GPIO.exe $(_FLATRELEASEDIR)\GPIO.exe NK S
SMBUS.exe $(_FLATRELEASEDIR)\SMBUS.exe NK S
„ Place the three files into any files directory.
„ Build your new Windows CE operating system.
41
PCM-3362 User Manual
Software Introduction & Installation
Note!
Chapter 4
\Demo
4.3.5 SUSI Sample Programs
Sample Programs
The sample programs demonstrate how to incorporate SUSI into your program.
There are sample programs for two categories of operating system, i.e. Windows XP
and Windows CE. The sample programs run in graphics mode in Windows XP and
Windows CE. The sample programs are described in the subsections below.
Windows Graphics Mode
There are sample programs of Windows in graphics mode for two categories of operating system, i.e. Windows CE and Windows XP. Each demo application contains an
executable file SusiDemo.exe, a shared library Susi.dll and source code within the
release package. The files of Windows CE and Windows XP are not compatible with
each other.
SusiDemo.exe is an executable file and it requires the shared library, Susi.dll, to
demonstrate the SUSI functions. The source code of SusiDemo.exe also has two
versions, i.e. Windows CE and Windows XP, and must be compiled under Microsoft
Visual C++ 6.0 on Windows XP or under Microsoft Embedded Visual C++ 4.0 on
Windows CE. Developers must add the header file Susi.h and library Susi.lib to their
own projects when they want to develop something with SUSI.
SusiDemo.exe
The SusiDemo.exe test application is an application which uses all functions of the
SUSI Library. It has five major function blocks: Watchdog, GPIO, SMBus, I2C and
VGA control. The following screen shot appears when you execute SusiDemo.exe.
You can click function tabs to select test functions respectively. Some function tabs
will not show on the test application if your platform does not support such functions.
For a complete support list, please refer to Appendix A. We describe the steps to test
all functions of this application.
GPIO
PCM-3362 User Manual
42
Chapter 4
„
Test Read Multiple Input Pin
– Click the radio button- Multiple-Pins.
– Key in the pin number from ‘0x01’ to ‘0x0F’ to read the value of the input pin.
The pin numbers are ordered bitwise, i.e. bit 0 stands for GPIO 0, bit 1 stands
for GPIO 1, etc. For example, if you want to read pin 0, 1, and 3, the pin numbers should be ‘0x0B’.
– Click READ GPIO DATA button and the statuses of the GPIO pins will be displayed in (R/W) Result field.
„
Test Write Single Output Pin
– Click the radio button- Single-Pin.
– Key in the pin numbers you want to write. Pin numbers start from '0'.
– Key in the value either '0' or '1' in (R/W) Result field to write the output pin you
chose above step.
– Click the WRITE GPIO DATA button to write the GPIO output pin.
„
Test Write Multiple Output Pins
– Click the radio button- Multiple-Pins.
– Key in the pin number from ‘0x01’ to ‘0x0F’ to choose the multiple pin numbers to write the value of the output pin. The pin numbers are ordered bitwise, i.e. bit 0 stands for GPIO 0, bit 1 stands for GPIO 1, etc. For example, if
you want to write pin 0, 1, and 3, the pin numbers should be ‘0x0B’.
– Key in the value in (R/W) Result field from ‘0x01’ to ‘0x0F’ to write the value
of the output pin. The pin numbers are ordered bitwise, i.e. bit 0 stands for
GPIO 0, bit 1 stands for GPIO 1, etc. For example, if you want to set pin 0
43
PCM-3362 User Manual
Software Introduction & Installation
When the application is executed, it will display GPIO information in the GPIO
INFORMATION group box. It displays the number of input pins and output pins. You
can click the radio button to choose to test either the single pin function or multiple
pin functions. The GPIO pin assignments of the supported platforms are located in
Appendix B.
„ Test Read Single Input Pin
– Click the radio button- Single-Pin.
– Key in the pin number to read the value of the input pin. The Pin number
starts from '0'.
– Click the READ GPIO DATA button and the status of the GPIO pin will be displayed in (R/W) Result field.
and 1 high, 3 to low, the pin number should be ‘0x0B/, and then you should
key in the value ‘0x0A’ to write.
– Click the WRITE GPIO DATA button to write the GPIO output pins.
I2 C
When the application is executed, you can read or write a byte of data through I2C
devices. All data must be read or written in hexadecimal system.
„
Read a byte
– Key in the slave device address in Slave address field.
– Key in the register offset in Register Offset field.
– Click the READ A BYTE button and then a byte of data from the device will
be shown on the Result field.
Write a byte
– Key in the slave device address in Slave address field.
– Key in the register offset in Register Offset field.
– Key in the desirous of data in Result field to write to the device.
– Click the WRITE A BYTE button and then the data will be written to the
device through I2C.
SMBus
„
When the application has executed, you can click the radio button to choose to test
each access mode, i.e. Access a byte, Access multiple bytes and Access a word. All
data must be read or written in hexadecimal except the numbers for radio button:
Access multiple bytes mode must be written in decimal. You can test the functionalities of the watchdog as follows:
„ Read a byte
PCM-3362 User Manual
44
Click the radio button- Access a byte.
Key in the slave device address in the Slave address field.
Key in the register offset in the Register Offset field.
Click the READ SMBus DATA button and a byte of data from the device will
be shown on the Result field.
Write a byte
– Click the radio button- Access a byte.
– Key in the slave device address in Slave address field.
– Key in the register offset in Register Offset field.
– Key the desired data in the Result field to write to the device.
– Click the WRITE SMBus DATA button and then the data will be written to the
device through SMBus.
„
Read a word
– Click the radio button- Access a word.
– Key in the slave device address in the Slave address field.
– Key in the register offset in the Register Offset field.
– Click the READ SMBus DATA button and then a word of data from the device
will be shown on the Result field.
„
Write a word
– Click the radio button- Access a word.
– Key in the slave device address in the Slave address field.
– Key in the register offset in the Register Offset field.
– Key in the desired data, such as 0x1234, in the Result field to write to the
device.
– Click the WRITE SMBus DATA button and the data will be written to the
device through the SMBus.
„
Read Multiple bytes
– Click the radio button- Access multiple bytes.
– Key in the slave device address in the Slave address field.
– Key in the register offset in the Register Offset field.
– Key in the desired number of bytes, such as 3, in the right side field of radio
button- Access multiple bytes. The number must be written in decimal.
– Click the READ SMBus DATA button and then all data from the device will be
divided from each other by commas and be shown in the Result field.
„
Write Multiple bytes
– Click the radio button- Access multiple bytes.
– Key in the slave device address in the Slave address field.
– Key in the register offset in the Register Offset field.
– Key in the desired number of bytes, such as 3, in the right side field of the
radio button- Access multiple bytes. The number must be written in decimal.
– Key in all the desired data in the Result field in hexadecimal format, divided
by commas, for example, 0x50,0x60,0x7A.
– Click the WRITE SMBus DATA button and all of the data will be written to the
device through the SMBus.
45
PCM-3362 User Manual
Software Introduction & Installation
„
Chapter 4
–
–
–
–
Display Control
When the application is executed, it will display two blocks of VGA control functions.
The application can turn on or turn off the screen shot freely, and it also can tune the
brightness of the panels if your platform is being supported. You can test the functionalities of VGA control as follows:
„ Screen on/off control
– Click the radio button ON or push the key F11 to turn on the panel screen.
– Click the radio button OFF or push the key F12 to turn off the panel screen.
– The display chip of your platform must be in the support list in Appendix A, or
this function cannot work.
„ Brightness control
– Move the slider in increments, using either the mouse or the direction keys,
or click the UP button to increase the brightness.
– Move the slider in decrements, using either the mouse or the direction keys,
or click the DOWN button to decrease the brightness.
Watchdog
When the application is executed, it will display watchdog information in the WATCHDOG INFORMATION group box. It displays max timeout, min timeout, and timeout
steps in milliseconds. For example, a 1~255 seconds watchdog will has 255000 max
timeout, 1000 min timeout, and 1000 timeout steps. You can test the functionality of
the watchdog as follows:
PCM-3362 User Manual
46
„
„
Set the timeout value 3000 (3 sec.) in the SET TIMEOUT field and set the delay
value 2000 (2 sec.) in the SET DELAY field, then click the START button. The
Timeout Countdown field will countdown the watchdog timer and display 5000
(5 sec.).
Before the timer counts down to zero, you can reset the timer by clicking the
REFRESH button. After you click this button, the Timeout Countdown field will
display the value of the SET TIMEOUT field.
If you want to stop the watchdog timer, you just click the STOP button.
CL
When the Monitor application is executed by clicking the button, hardware monitoring
data values will be displayed. If certain data values are not supported by the platform,
the correspondent data field will be grayed-out with a value of 0.
For More detail PCM-3362 software API user manual, please contact your dealer or
Advantech AE. We also include these manuals in this CD.
47
PCM-3362 User Manual
Software Introduction & Installation
Hardware Monitor
Chapter 4
„
PCM-3362 User Manual
48
Chapter
5
Chipset Software
Installation Utility
5
5.1 Before You Begin
To facilitate the installation of the enhanced display drivers and utility software, read
the instructions in this chapter carefully. The drivers for the PCM-3362 are located on
the software installation CD. The driver in the folder of the driver CD will guide and
link you to the utilities and drivers under a Windows system. Updates are provided
via Service Packs from Microsoft*.
Note!
The files on the software installation CD are compressed. Do not
attempt to install the drivers by copying the files manually. You must use
the supplied SETUP program to install the drivers.
Before you begin, it is important to note that most display drivers need to have the
relevant software application already installed in the system prior to installing the
enhanced display drivers. In addition, many of the installation procedures assume
that you are familiar with both the relevant software applications and operating system commands. Review the relevant operating system commands and the pertinent
sections of your application software’s user manual before performing the installation.
5.2 Introduction
The Intel® Chipset Software Installation (CSI) utility installs the Windows INF files
that outline to the operating system how the chipset components will be configured.
This is needed for the proper functioning of the following features:
„ Core PCI PnP services
„ Serial ATA interface support
„ USB 1.1/2.0 support (USB 2.0 driver needs to be installed separately for Win98)
„ Identification of Intel® chipset components in the Device Manager
„ Integrates superior video features. These include filtered sealing of 720 pixel
DVD content, and MPEG-2 motion compensation for software DVD
5.3 Windows XP/Vista/Win7 Driver Setup
Insert the driver CD into your system’s CD-ROM drive. You can see the driver folder
items. Navigate to the "PCM-3362\01_chipset folder, and find folders including Win
XP, Vista, and Win 7 and choose which of OS you would like to install, and click
"infinst_autol.exe" to complete the installation of the driver.
Note!
Wrong driver installation may cause unexpected system instability.
PCM-3362 User Manual
50
Chapter
6
6
Integrated Graphic
Device Setup
6.1 Introduction
To benefit from the Intel® Atom N450 integrated graphics controller, you need to
install the graphic driver.
6.2 Windows XP/ Vista /Win7 Driver Setup
Note!
1.
2.
3.
4.
5.
Before installing this driver, make sure the chipset driver has been
installed in your system. See Chapter 5 for information on installing the
chipset driver.
Insert the driver CD into your system’s CD-ROM drive. You can see the driver
folder items. Navigate to the "PCM-3362\02_ Graphic folder, and find folders
including Win XP, Vista, and Win 7 and choose which of OS you would like to
install.
Locate and highlight the "igxp32.INF" (if 32-bit) or "igxp64.INF" (if 64-bit).Click
on the "Open" button.
Click on the "OK" button. A window listing all of the available display types
should open. Select the display adapter that your system contains and then click
on the "Next" button.
Click on the "Next" button. The operating system will install the driver. Click on
the "Finish" button when done.
Click on the "Close" button and then click on the "Yes" button to reboot. The
driver should now be loaded.
PCM-3362 User Manual
52
Chapter
7
7
LAN Configuration
7.1 Introduction
The PCM-3362 has Gigabit Ethernet LAN via dedicated PCI Express x 1 lanes (Intel
82567V), that offer bandwidth of up to 500 MB/sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet to operate at 1000Mbps.
7.2 Installation
Note!
Before installing this driver, make sure the chipset driver has been
installed in your system. See Chapter 5 for information on installing the
chipset driver.
The PCM-3362s Intel 82567V Gigabit controller supports all major network operating
systems. However, the installation procedure varies with different operating systems.
Please find and use the section that provides the driver setup procedure for the operating system you are using.
7.3 Windows XP/ Vista /Win7 Driver Setup
Insert the driver CD into your system’s CD-ROM drive. You can see the driver folder
items. Navigate to the "PCM-3362\03 LAN” folder and click autorun program to complete the installation of the driver.
PCM-3362 User Manual
54
Appendix
A
A
Pin Assignments
This appendix contains information of a detailed or specialized
nature.
Sections include:
„ Jumper and Connector Tables
A.1 Jumper and Connector Tables
JP1
CLEAR CMOS
Part Number
1653003101
Footprint
JH3X1V-2M
Description
PIN HEADER 3*1P 180D(M) 2.0mm DIP SQUARE W/O Pb
Setting
Function
(1-2)
NORMAL (Default)
(2-3)
CLEAR CMOS
JP2
LVDS PANEL POWER Select
Part Number
1653003101
Footprint
JH3X1V-2M
Description
PIN HEADER 3*1P 180D(M) 2.0mm DIP SQUARE W/O Pb
Setting
Function
(1-2)
5V for +VLVDS_PANEL POWER Select
(2-3)
3.3V for +VLVDS_PANEL POWER Select (Default)
JP3
COM3 RS422/RS485 Select
Part Number
1653003101
Footprint
JH3X1V-2M
Description
PIN HEADER 3*1P 180D(M) 2.0mm DIP SQUARE W/O Pb
Setting
Function
(1-2)
RS485 (default)
(2-3)
RS422
JP4
PCI I/O Voltage Select
PCM-3362 User Manual
56
1653002101
Footprint
JH2X1V-2M
Description
PIN HEADER 2*1P 180D(M)SQUARE 2.0mm DIP W/O Pb
Setting
Function
(1-2)
5V for PCI I/O Voltage Select (default)
(2-3)
3.3V for PCI I/O Voltage Select
CN1
HD Audio Connector
Part Number
1653008101
Footprint
JH8X1V-2M
Description
PIN HEADER 8*1P 180D(M) 2.0mm DIP 209-1*8GS
Pin
Pin Name
Signal Type
Signal Level
1
+V5
PWR
+5 V
2
GND
3
AZ_BITCLK
CLK
4
AZ_SYNC
I/O
5
AZ_RST#
I/O
6
AZ_SDIN0
IN
7
AZ_SDOUT
OUT
8
+V12
PWR
+12 V
CN4
DDR2 SO-DIMM
Part Number
1651000087
Footprint
DDR-SODIMM-STD65
Description
SKT DIMM 200P DDR2 H=6.5mm STD SMD WO/Pb
1 3
17 19
2 4
18 20
CN6
LVDS Connector
Part Number
1653910261
Footprint
SPH10X2
Description
*CONN. SMD 10*2P 180D(M)DF13-20DP-1.25V(91) HRS
Pin
Pin Name
1
GND
2
GND
3
LVDS0_z_D0+
4
N/C
5
LVDS0_z_D0-
6
N/C
7
LVDS0_z_D1+
57
Signal Type
Signal Level
OUT
LVDS
OUT
LVDS
OUT
LVDS
PCM-3362 User Manual
Appendix A Pin Assignments
Part Number
8
N/C
9
LVDS0_z_D1-
10
N/C
OUT
LVDS
OUT
LVDS
OUT
LVDS
11
LVDS0_z_D2+
12
N/C
13
LVDS0_z_D2-
14
N/C
15
LVDS0_z_CLK+ OUT
LVDS
16
N/C
17
LVDS0_z_CLK- OUT
LVDS
18
N/C
19
+V_LCD
PWR
+5 V/+3.3 V
20
+V_LCD
PWR
+5 V/+3.3 V
1
5
CN7
Internal LCD Backlight
Part Number
1655305020
Footprint
WHL5V-2M
Description
WAFER BOX 2.0mm 5P 180D(M) W/LOCK
Pin
Pin Name
Signal Type
Signal Level
1
+V12_INVERTER
PWR
+12V
2
GND
GND
3
LVDS0_ENABKL
OUT
+3.3V
4
LVDS0_VBR
OUT
+3.3V
5
+V5_INVERTER
PWR
+5V
CN8
VGA Connector
Part Number
1655912120
Footprint
WB12P-S1.25mm
Description
Wafer Box 1.25mm 12P 90D(M) SMD 85204-12001
Pin
Pin Name
Signal Type
1
GND
GND
2
VGA_z_R
OUT
+5 V
3
VGA_z_G
OUT
+5 V
4
VGA_z_B
OUT
+5 V
5
GND
GND
6
+V5_CRT
PWR
+5 V
7
VGA_z_DDAT
OUT
+5 V
8
VGA_z_DCLK
OUT
+5 V
9
GND
GND
10
VGA_z_HS
OUT
+5 V
11
VGA_z_VS
OUT
+5 V
12
GND
GND
PCM-3362 User Manual
58
Signal Level
1
6 8 10
3 5 7
9
CN9
USB0/1
Part Number
1653003718
Footprint
PH5x2P-SR2.00
Description
PIN HEADER 5*2P 2.00mm 90D(M) NO.10 SMD
Pin
Pin Name
Signal Type
Signal Level
1
+V5_USB0
PWR
+5 V
2
+V5_USB0
PWR
+5 V
3
USB0_z_P-
I/O
4
USB1_z_P-
I/O
5
USB0_z_P+
I/O
6
USB1_z_P+
I/O
7
GND
8
GND
9
GND
2 4
1
6 8 10
3 5 7 9
CN10
USB2/3
Part Number
1653003718
Footprint
PH5x2P-SR2.00
Description
PIN HEADER 5*2P 2.00mm
90D(M) NO.10 SMD
Pin
Pin Name
Signal Type
Signal Level
1
+V5_USB0
PWR
+5 V
2
+V5_USB0
PWR
+5 V
3
USB2_z_P-
I/O
4
USB3_z_P-
I/O
5
USB2_z_P+
I/O
6
USB3_z_P+
I/O
7
GND
8
GND
9
GND
59
PCM-3362 User Manual
Appendix A Pin Assignments
2 4
CN12
Front panel Connector
Part Number
1653008101
Footprint
JH8X1V-2M
Description
PIN HEADER 8*1P 180D(M) 2.0mm DIP 209-1*8GS
Pin
Pin Name
Signal Type
Signal Level
1
PSIN#
IN
+3.3 V
2
GND
3
RESET
4
GND
5
PWR_LED
6
GND
7
+V3.3
PWR
8
HD_LED
OUT
CN13
Buzzer Connector
Part Number
1653002101
Footprint
HD_2x1P_79_D
Description
PIN HEADER 2*1P 180D(M)SQUARE 2.0mm DIP W/O Pb
Pin
Pin Name
Signal Type
Signal Level
1
+V3.3
PWR
+3.3 V
2
SB_z_SPKR
OUT
IN
OUT
CN15
SATA1 connector
Part Number
1654000128
Footprint
SATA-LD11071S02
Description
Serial ATA 7P 90D(M) SMD 15u Reverse
+3.3 V
Pin
Pin Name
Signal Type
1
GND
GND
2
SATA0_TX+
I/O
Analog
3
SATA0_TX-
I/O
Analog
4
GND
GND
5
SATA0_RX-
I/O
Analog
6
SATA0_RX+
I/O
Analog
7
GND
GND
PCM-3362 User Manual
60
Signal Level
18 20
1 3
17 19
CN16
COM1~COM2 Connector
Part Number
1653003720
Footprint
HD_10x2P_79_RA
Description
PIN HEADER 10*2P 2.00mm 90D(M) SMD 21N22050-20J1
Pin
Pin Name
Signal Type
Signal Level
1
COM0_DCD#
IN
+5 V
2
COM0_DSR#
IN
+5 V
3
COM0_RXD
IN
+5 V
4
COM0_RTS#
I/O
+5 V
5
COM0_TXD
OUT
+5 V
6
COM0_CTS#
IN
+5 V
7
COM0_DTR#
I/O
+5 V
8
COM0_RI#
IN
+5 V
9
GND
10
GND
11
COM1_DCD#
IN
+5 V
12
COM1_DSR#
IN
+5 V
13
COM1_RXD
IN
+5 V
14
COM1_RTS#
I/O
+5 V
15
COM1_TXD
OUT
+5 V
16
COM1_CTS#
IN
+5 V
17
COM1_DTR#
I/O
+5 V
18
COM1_RI#
IN
+5 V
19
GND
20
GND
1
2
3
4
CN17
RS422/485 Connector
Part Number
1655304120
Footprint
WHL4H-2M_A
Description
WAFER BOX 2.0mm 4P 90D(M) DIP W/LOCK
Pin
Pin Name
Signal Type
Signal Level
1
RS422_RXD-
I/O
+5 V
2
RS422_RXD+
I/O
+5 V
3
RS485_422_TXD+
I/O
+5 V
4
RS485_422_TXD-
I/O
+5 V
61
PCM-3362 User Manual
Appendix A Pin Assignments
2 4
2 4
1
6 8 10
3 5 7
9
CN18
LAN Connector
Part Number
1653003719
Footprint
HD_5x2P_79_RA_21N22050
Description
PIN HEADER 5*2P 2.00mm 90D(M) SMD 21N22050-10J10
Pin
Pin Name
Signal Type
A1
GNDT
GND
A2
GNDT
GND
A3
LAN1_M3+
I/O
Analog
A4
LAN1_M3-
I/O
Analog
A5
LAN1_M2+
I/O
Analog
A6
LAN1_M2+
I/O
Analog
A7
LAN1_M1+
I/O
Analog
A8
LAN1_M1+
I/O
Analog
Signal Level
A9
LAN1_M0+
I/O
Analog
A10
LAN1_M0+
I/O
Analog
CN19
LAN LED Connector
Part Number
1653004101
Footprint
HD_4x1P_79_D
Description
PIN HEADER 4*1P 180D(M) 2.0mm DIP WO/Pb
Pin
Pin Name
Signal Type
Signal Level
1
+V3.3_LAN1
PWR
+3.3V
2
LAN1_ACT#
OUT
3
LAN1_1000#
OUT
4
LAN1_100#
OUT
CN20
PS2 Keyboard/Mouse Connector
Part Number
1655306020
Footprint
WHL6V-2M
Description
WAFER BOX 2.0mm 6P 180D(M) W/LOCK
Pin
Pin Name
Signal Type
Signal Level
1
KB_z_CLK#
I/O
+5 V
2
KB_z_DAT#
I/O
+5 V
3
MS_z_CLK#
I/O
+5 V
4
GND
5
+V5_KB
PWR
+5 V
6
MS_z_DAT#
I/O
+5 V
PCM-3362 User Manual
62
GPIO Connector
Part Number
1653010102
Footprint
JH10X1V-2M
Description
PIN HEADER 10*1P 180D(M)
DIP P=2.0mm
Pin
Pin Name
Signal Type
Signal Level
1
+V5_GPIO
PWR
+5 V
2
DIO_IO0
I/O
+5 V
3
DIO_IO1
I/O
+5 V
4
DIO_IO2
I/O
+5 V
5
DIO_IO3
I/O
+5 V
6
DIO_IO4
I/O
+5 V
7
DIO_IO5
I/O
+5 V
8
DIO_IO6
I/O
+5 V
9
DIO_IO7
I/O
+5 V
10
GND
CN23
ATX Power In Connector
Part Number
1655303020
Footprint
WHL3V-2M
Description
WAFER BOX 2.0mm 3P 180D
w/LOCK
Pin
Pin Name
Signal Type
Signal Level
1
+V5_SB
PWR
+5 V
2
GND
3
PWR_PSON#
IN
CN24
Power In Connector
Part Number
1655308120
Footprint
WHL8H-2M
Description
Wafer Box 2.0mm 8P 90D Male W/Lock
Pin
Pin Name
Signal Type
Signal Level
1
+V5_ATX
PWR
+5 V
2
+V5_ATX
PWR
+5 V
3
+V5_ATX
PWR
+5 V
4
GND
5
GND
6
GND
7
GND
8
+V12
PWR
+12 V
63
PCM-3362 User Manual
Appendix A Pin Assignments
CN21
1
2
3
4
CN25
I2C BUS connector
Part Number
1653004101
Footprint
HD_4x1P_79_D
Description
PIN HEADER 4*1P 180D(M) 2.0mm DIP WO/Pb
Pin
Pin Name
1
GND
Signal Type
Signal Level
2
I2 C_DAT
I/O
3
I2 C_CLK
I/O
4
+V5_I2C
PWR
+5V
CN26
-12V & -5V power connector
Part Number
1653003101
Footprint
HD_3x1P_79_D
Description
PIN HEADER 3*1P 180D(M)
2.0mm DIP SQUARE W/O Pb
Pin
Pin Name
Signal Type
Signal Level
1
-V5
PWR
-5 V
PWR
-12 V
2
GND
3
-V12
PCM-3362 User Manual
64
Appendix
B
B
System Assignments
This appendix contains information of a detailed nature.
Sections include:
„ System I/O ports
„ 1st MB memory map
„ DMA channel assignments
„ Interrupt assignments
B.1 System I/O Ports
Table B.1: System I/O ports
Addr. range (Hex)
Device
000-01F
DMA controller
020-021
Interrupt controller 1, master
040-05F
8254 timer
060-06F
8042 (keyboard controller)
070-071
Real-time clock, non-maskable interrupt (NMI) mask
87-8A
DMA page register
0A0-0A1
Interrupt controller 2
0C0-0DF
DMA controller
1F0-1F8
Fixed disk
278-27F
Reserved (Parallel port 2,LTP3)
2E8-2EF
Reserved (Series port 4)
2F8-2FF
Serial port 2
378-37F
Parallel printer port 1 (LPT 2)
3B0-3BF
Monochrome display and printer adapter (LPT1)
3D0-3DF
Color/graphics monitor adapter
3E8-3EF
Series port 3
3F0-3F7
Diskette controller
3F8-3FF
Serial port 1
* PNP audio I/O map range from 220 ~ 250H (16 bytes) MPU-401 select from 300 ~
330H (2 bytes)
B.2 1st MB Memory Map
Table B.2: 1st MB memory map
Addr. range (Hex)
Device
F0000h - FFFFFh
System ROM
*CC000h - EFFFFh
Unused (reserved for Ethernet ROM)
C0000h - CBFFFh
Expansion ROM (for VGA BIOS)
B8000h - BFFFFh
CGA/EGA/VGA text
B0000h - B7FFFh
Unused
A0000h - AFFFFh
EGA/VGA graphics
00000h - 9FFFFh
Base memory
* If Ethernet boot ROM is disabled (Ethernet ROM occupies about 16 KB)
* E0000 - EFFFF is reserved for BIOS POST
B.3 DMA channel assignments
Table B.3: DMA channel assignments
Channel
Function
0
Available
PCM-3362 User Manual
66
Appendix B System Assignments
Table B.3: DMA channel assignments
1
Available (audio)
2
Floppy disk (8-bit transfer)
3
Available (parallel port)
4
Cascade for DMA controller 1
5
Available
6
Available
7
Available
* Audio DMA select 1, 3, or 5
** Parallel port DMA select 1 (LPT2) or 3 (LPT1)
B.4 Interrupt assignments
Table B.4: Interrupt assignments
Interrupt#
Interrupt source
IRQ 0
Interval timer
IRQ 1
Keyboard
IRQ 2
Interrupt from controller 2 (cascade)
IRQ 3
COM2
IRQ 4
COM1
IRQ 5
Reserved (COM4)
IRQ 6
FDD
IRQ 7
LPT1
IRQ 8
RTC
IRQ 9
Reserved (audio)
IRQ 10
Reserved (COM3)
IRQ 11
Reserved
IRQ 12
PS/2 mouse
IRQ 13
INT from co-processor
IRQ 14
Primary IDE
IRQ 15
Reserved
67
PCM-3362 User Manual
PCM-3362 User Manual
68
Appendix
C
C
Mechanical Drawings
C.1 Board Mechanical Drawings
Figure C.1 PCM-3362 Mechanical Drawing (Component Side)
PCM-3362 User Manual
70
Appendix C Mechanical Drawings
Figure C.2 PCM-3362 Mechanical Drawing (Solder Side)
71
PCM-3362 User Manual
C.2 Heatsink Mechanical Drawings
Figure C.3 PCM-3362N Heatsink Mechanical Drawing
Figure C.4 PCM-3362Z/Z2 Heatsink Mechanical Drawing for wide temperature
version
PCM-3362 User Manual
72
Figure C.5 PCM-3362 optional Heatspreader Mechanical Drawing
73
PCM-3362 User Manual
Appendix C Mechanical Drawings
C.3 Optional Heat spreader Mechanical Drawings
PCM-3362 User Manual
74
Appendix
D
D
Watchdog Timer and
GPIO sample code
D.1 Watchdog Timer sample code
;The SCH3114 Runtime base I/O address is A00h
;Setting WatchDog time value location at offset 66h
;If set value "0", it is mean disable WatchDog function. Superio_GPIO_Port = A00h
mov dx,Superio_GPIO_Port + 66h
mov al,00h out dx,al
.model small
.486p
.stack 256
.data
SCH3114_IO EQU A00h
.code
org 100h
.STARTup
;====================================================
;90H
;enable WDT function bit [0]=01h
;====================================================
mov dx,SCH3114_IO + 90h mov al,01h
out dx,al
;====================================================
;65H
;bit [1:0]=Reserved
;bit [6:2]Reserve=00000
;bit [7] WDT time-out Value Units Select
;Minutes=0 (default) Seconds=1
;====================================================
mov dx,SCH3114_IO + 65h ;
mov al,080h out dx,al
;====================================================
;66H
;WDT timer time-out value
;bit[7:0]=0~255
;====================================================
mov dx,SCH3114_IO + 66h mov al,01h
out dx,al
;====================================================
;bit[0] status bit R/W
;WD timeout occurred =1
;WD timer counting = 0
;====================================================
mov dx,SCH3114_IO + 68h
mov al,01h
out dx,al
.exit
PCM-3362 User Manual
76
D.2 GPIO sample code
;===============================================================
; Get Number of GPIO group
; one group mean 8 gpio pins (one GPIO Chip)
; Input:
; ax=5E87h
; bh=00h
; output:
; ax=5E78 ;function success, other value means function fail
; cl= n group of gpio
mov ax,5E87h
mov bh,00h
INT15
;
You will get cl=01 in 8 bit GPIO product, cl = 02 in 16 bit GPIO product
;===============================================================
;===============================================================
; Get GPIO Config
; Input:
; ax=5E87h
; bh=01h
; cl= n ; n means which group of GPIO you want to get
; output:
; ax=5E78 ;function success, other value means function fail
; bl= the n group of gpio config
;
bit 0 = gpio 0 , 0 => output pin; 1 => input pin
;
bit 1 = gpio 1 , 0 => output pin; 1 => input pin
;
.....
;
bit 7 = gpio 7 , 0 => output pin; 1 => input pin
mov ax,5E87h
mov bh,01h
mov cl,01h
INT15
;
You will get GPIO default setting from bl
;===============================================================
;===============================================================
; Set GPIO Config
; Input:
; ax=5E87h
; bh=02h
77
PCM-3362 User Manual
Appendix D Watchdog Timer and GPIO sample code
END
; cl= n ; n means which group of GPIO you want to set
; bl= the n group of gpio config
;
bit 0 = gpio 0 , 0 => output pin; 1 => input pin
;
bit 1 = gpio 1 , 0 => output pin; 1 => input pin
;
.....
;
bit 7 = gpio 7 , 0 => output pin; 1 => input pin
; output:
; ax=5E78 ;function success, other value means function fail
mov ax,5E87h
mov bx,02AAh
mov cl,01
INT15
;
Set GPIO 0,2,4,6 as output, GPI 1,3,5,7 as input
;===============================================================
;===============================================================
; Get GPIO status
; Input:
; ax=5E87h
; bh=03h
; cl= n ; n means which group of GPIO you want to get
; output:
; ax=5E78 ;function success, other value means function fail
; bl= the n group of gpio status
;
bit 0 = gpio 0 , 0 => Low; 1 => High
;
bit 1 = gpio 1 , 0 => Low; 1 => High
;
.....
;
bit 7 = gpio 7 , 0 => Low; 1 => High
mov ax,5E87h
mov bh,03h
mov cl,01h
INT15
;
You will get GPIO value from bl
;===============================================================
;===============================================================
; Set GPIO status
; Input:
; ax=5E87h
; bh=04h
; cl= n ; n means which group of GPIO you want to set
; bl= the n group of gpio status
;
bit 0 = gpio 0 , 0 => Low; 1 => High
PCM-3362 User Manual
78
mov ax,5E87h
mov bx,0400h
mov cl,01
INT15
;
Set GPIO 0,2,4,6 Output Low
;===============================================================
79
PCM-3362 User Manual
Appendix D Watchdog Timer and GPIO sample code
;
bit 1 = gpio 1 , 0 => Low; 1 => High
;
.....
;
bit 7 = gpio 7 , 0 => Low; 1 => High
; output:
; ax=5E78 ;function success, other value means function fail
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2009
Download PDF