VIETA | DVD-50 | Instruction manual | VIETA DVD-50 Instruction manual

DVD-50
INSTRUCTION MANUAL
SAFETY
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFERS SERVICING TO
QUALIFIED PERSONAL ONLY.
Laser: This Digital Video Disc Receiver employs a Laser System.
To ensure proper use of this product, please read this owner manual carefully and retain for future reference. Should the unit
requires maintenance, contact an authorized service location see service procedure.
Use of controls or the performance of procedures other than those specified may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible and invisible laser radiation when open and
interlocks defeated.
Do not stare into beam
This appliance is classified as a LASER KLASSE 1. The LASER
KLASSE 1 is located on the rear panel. This product contains a
low power laser device. To ensure continued safety, do not
remove any cover or attempt to gain access to the inside of the
product.
LASER KLASSE 1
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
Caution:
- Use of controls or adjustments or performance of procedures other than those specified may result in
hazardous radiation exposure.
- The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
- The socket -outlet shall be installed near the equipment and shell be easily accessible.
The following marking is printed on the rear panel.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol is intended to alert the user of the presence of uninsulated dangerous
voltage within the product’s encasement that may be of sufficient magnitude to
concede a risk of electric shock to persons.
This symbol is intended to alert the user of the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
2
TABLE OF CONTENTS
Introduction
­
­
­
page 4 ~ 5
Remote control
Front panel
Back panel
Care and maintenance
­
­
­
Connection
­
­
­
­
­
­
­
­
­
­
­
­
­
­
­
­
­
­
­
­
­
­
­
­
­
page 7 ~ 8
Troubleshooting
page 15
Technical specifications
page 16
Basic play
Basic playback
Slow motion play
Fast search
Picture zooming
Repeat
Angle selection
Special functions
­
Cleaning the components
Notes about compact disc (DVD video CD,
Video CD, audio CD, MP3 CD)
Notes about the CD player.
page 6
Direct connection with a TV.
Inserting batteries into the remote control
Basic Operation
page 14
page 9 ~ 13
General setup
Setting the picture
Setting the sound
Special DVD / VCD features
Changing subtitle language
Changing sound track language
Display the disc information during playback
Moving to another title / chapter
Playback from a selected point
Repeat A-B
Playback control (PBC)
Program play
Selecting the surround sound mode
Dimming the display screen
Sleep timer setting
Special MP3 - CD features
Karaoke features
3
Introduction
Remote control
STANDBY
OPEN/CLOSE
13
1
2
1
2
3
4
5
6
7
8
9
MENU
DISC
3
14
0
15
4
5
16
OK
6
7
8
9
10
VOLUME
ANGLE
ZOOM
SLOW
17
18
19
MUTE
20
/
-
VOLUME AUDIO EQ REPEAT
11
12
P/I
21
22
Front Panel
27 28 29 30 31
23
25
24
Back Panel
32
4
33
34
35
36
37
38
39 40
41
26
Introduction
Please refer PAGE 3 to find the parts more easily.
Remote Control
1. STANDBY
2. NUMBER keys (0~9)
3. MENU
4.
Turn the system POWER ON or STANDBY.
Select the items or setting directly.
Displays setup menu when stopped and disc menu when playing.
Play backward quickly (fast search).
5.
(Active Navigation keys) advance in indicated directions for making selections in menus and active
navigation mode.
6.
7. ANGLE
8.
VOLUME
9.
10. MUTE
11.
12. AUDIO EQ
13. Open / Close
14. DISC
15.
16. OK
17.
18. ZOOM
19. SLOW
20.
21. P/I
22. REPEAT
Skips to previous chapter or track.
Display angle menu if present on discs.
Increase the master volume level.
Start or Pause the playing disc.
Press to shut off the sound.
Decrease the master volume level.
Press the master volume level.
Open or close the disc tray.
To enter or exit the disc contents menu.
Plays forward quickly.
Confirms selection.
Skips to next chapter or track.
Selects zooming options when playing DVD.
In DISC mode, do the slow-motion playing.
Stop playing.
Switch the TV between progressive and interlace mode.
Press to do repeatedly.
Front panel
23. POWER
24. DISC TRAY
25. PHONE
26. VOL (+/-)
27.
EJECT
28.
STOP
29. PREV
30. NEXT
31. PLAY/PAUSE
Main switch to power on or off.
Connect to the headphone. (Headphone not included.)
Press to set the volume of the microphone.
Open or close the disc tray.
Press to stop the playback.
Skips to previous chapter or track.
Skips to next chapter or track.
Press to start or stop temporary the playback.
Back panel
32. AC LINE CORD
33. WOOFER LINE OUT
34. SPEAKERS OUTPUT TERMINAL
35. AUDIO OUT
36. OPTICAL
37. COAXIAL
38. SCART OUT
39. S-VIDEO OUT
40. VIDEO OUT
41. Pr / Cr / Pb / Cb Y (COMPONENT
VIDEO OUT)
Connect to AC outlet.
Connect to an active subwoofer.
Connect to amplified speakers.
Connect to a TV set, or other stereo receiver.
Connect to an optional receiver.
Connect to an optional receiver.
Connect to a TV with Scart input.
Connect to a TV S - VIDEO input connector.
Connect to a TV Video input connector.
Connect to TV with Pr / Cr / Pb / Cb Y input.
5
Connections
Direct Connection with TV
SCART IN
Pr/Cr
Pb/Cb
VIDEO IN
Y
COAXIAL IN
AUDIO IN
OPTICAL IN
S-VIDEO IN
use the SCART cable to connect SCART jack to a TV with the corresponding SCART input jack. The Scart terminal contains
separate video signal and stereo audio signals.
u If your TV have no SCART input jack, you can select one of the following connections as below option:
- Connect the S-VIDEO OUT jack to the S-Video input jack on the TV using a S-Video cable.
- Connect the VIDEO OUT jack to the Video input jacks on the TV using a video cable.
u Use the audio cables to connect AUDIO OUT jacks to the corresponding AUDIO IN jacks on the TV, CD or TAPE recorder.
u Use the Digital cables to connect OPTICAL or COAXIAL jack to correspond to receive digital signal.
u Connect to an amplifier with DTS, Dolby Digital decoder or CD recorder.
u
Note:
For suggestion, the connected cable must less than 3 meter.
Insert Batteries into the Remote Control
You can control the system using the supplied remote control. Insert two batteries by
matching the + and - on the batteries. When using the remote control, point it at the
remote sensor on the front panel of this system.
NOTE:
l Do not leave the remote in an extremely hot or humid place.
l Do not use a new battery with an old one.
l Do not drop any foreign object into the remote casing, particularly when replacing
the batteries.
l Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so
may cause a malfunction.
l If you will not use the remote for an extended period of time, remove the batteries to
avoid possible damage from battery leakage and corrosion.
6
+
-
+
Basic Operations
Proper setup of the unit can let you enjoy better sound and picture quality as well as convenient features. The selections and the preferred
options that will be chosen if they are available on a disc. If the disc loaded does not have the preferred option then the disc’s own preference
will be used.
Basic Play
Slow motion play
1.
When you complete all the connections, plug in the AC power
cord of the player.
2.
Press POWER to switch ON the main power.
3.
Press VOL +/- to increase or decrease the volume level.
Press remote SLOW to play in slow motion.
For DVD discs
Press it repeatedly to select the slow motion speed:
SF (forward) SR (reverse)
SF x 2
SF x 4
SF x 8
SR x 2
SR x 4
OFF cyclically.
4.
Press MUTE to shut off the sound. To restore the volume, press
it again.
5.
6.
Skip to another track/chapter
Press remote
/
repeatedly during playback to skip to
next or previous track / chapter.
SR x 8
For VCD discs
Press it repeatedly to select the slow motion speed:
SF(forward) : SF x 1, SF x 2, SF x 3, SLOW OFF.
Note
The sound will be muted during slow-motion play.
Press OPEN/CLOSE to open the disc tray, press again to close
the disc tray.
The following mode indicators inform you of the current
drive status.
On TV screen
On front panel display
DISC LOADING
OPEN
CLOSE
PLAY
NO DISC
BAD DISC
WAITING
LOADING
OPEN
CLOSE
PLAY
NO DISC
BAD DISC
DVD/SVCD/VCD/CD/MP3
Fast search
1
Press and hold
/
more than 1 second to fast reverse or
fast forward.
For DVD / Mp3 discs
FF (fast forward) : FF x 2, FF x 4, FF x 6, FF x 8, FF OFF
FR (fast reverse) : FR x 2, FR x 4, FR x 6, FR x 8, FR OFF
For VCD / CD discs
FF (fast forward) : FF x 1, FF x 2, FF x 3, FF x 4, PLAY
FR (fast reverse) : FR x 1, FR x 2, FR x 3, FR x 4, PLAY
2
In any FF or FR status, press PLAY/PAUSE
play.
to normal
Note
The sound will be muted during fast reverse or forward search.
Basic Playback
Start playback
Press PLAY/PAUSE
. To pause playback, press
again.
Note:
Some disc will start playing automatically, and other will display
the menu on the TV screen. Use the / / / to select the
track, or press the number keys (0 ~ 9) to go to the desired
track/chapter.
Stop playback
Press STOP
first time to temporary stop the playback.
Press this key again to go into entirely stop status.
NOTE
Your player will not play discs that have a region code different
from the region code of your player.
-
If the inhibit icon appears on the TV screen when a button is
pressed, it means the function is not available on the disc you
are playing.
7
Basic operations
Picture Zooming
Angle Selection
This function allows you to enlarge the picture on the TV screen and
to pan through the enlarge image.
Some DVD discs contain scenes which have been taken photos
simultaneously from a number of different angle. For these discs, the
same scenes can be viewed from each of different angles. (The
recorded angles different from disc to disc.) You should set the angle
mark to ON or press ANGLE key to set angle mark.
1
2
3
Press ZOOM repeatedly to select a zoom factor as below:
ZOOM
x 1.5
w
While playing a title shot from different angles, the angle mark
appears on TV screen. Off course, you can turn off it by
setting.
ZOOM
x2
w
Press the remote ANGLE button to change the scences from
one angle to another angle(s)
For example: 1/4, 2/4, 3/4, 4/4.
ZOOM
x3
ZOOM
OFF
To pan through the enlarge image, press OK to confirm the
zoom selection and use
/ /
/
keys to move the
zoomed picture left, right, up or down.
Some disc may not respond to the zoom feature.
Repeat
l
For DVD discs
Press REPEAT repeatedly to select the following on the display:
[REPEAT - 1] : repeat chapter
[REPEAT - A] : repeat title/disc
l
For VCD discs
Press REPEAT repeatedly to select the following on the display:
[REPEAT - 1] : repeat the current track
[REPEAT - A] : repeat the entire disc
Note
When operating function, the OSD will display the operating
information, but the VFD will not.
8
Special Functions
General setup
NTSC
If the connected TV is NTSC system, select this mode. It will
change the video signal of a PAL disc and output in NTSC format.
1
Press MENU to enter SETUP MENU
2
Use
PAL
If the connected TV is PAL system, select this mode. It will change
the video signal of a NTSC disc and output in PAL format.
3
Press ENTER to confirm a highlighted selection.
4
To exit setup menu, press MENU.
* Video Out
Video out selection enable you to choose the type of video out put
suitable for your receiver.
Setting the picture
PR PB Y
Select PR PB Y, if you have connected the video output to your TV
using S-VIDEO jack.
/
/
/
to select your preferred option.
SCART
Select SCART, if you have connected the video output to your TV
using the Scart jack.
* Screen Saver
If set to ON, when you leave the system in stop or pause mode for
more than one minute, the screen saver will be activated.
* TV Shape
Select the aspect ratio of the TV to be connected.
Setting the sound
4:3 PS (default setting)
If you have a conventional TV set and your DVD is not
formatted for widescreen viewing, use this setting. A wide picture
is displayed on the whole TV screen with a portion
automatically cut off.
4:3 LB
If you have a conventional TV set and your DVD is formatted for
wide screen viewing, use this setting. Wide bands will be
displayed on the upper and whole portions of the TV screen.
16:9
If you have a widescreen TV set, use this setting (you must also
set your widescreen TV to “full size”).
16:9
(Wide screen)
4:3 LB
(Letter Box)
4:3 PS
(Pan Scan)
Note
If your DVD is not encoded to allow you to change the aspect
ratio, TV shape cannot be changed.
* Digital Output
Digital output selection enables you to specify the type of digital
output suitable for your amplifier or receiver.
Select ALL, if you have connected the digital output (COAXIAL or
OPTICAL) to a multichannel decoder receiver.
Select PCM 96K if the external component is capable of
processing digital signal input with sampling rates of 96 kHz.
Select PCM 48K if the external component is incapable of
processing 96kHz digital signal input, then convert to standard
signal with sampling rates of 48 kHz.
Select OFF to deactivate the digital output (COAXIAL or
OPTICAL).
* Night Mode
Set night mode to on to lever out the volume. For example, the disc
will be play at the same sound level throughout the movie. The
default setting is OFF.
-
Center Delay
If the listening position is close to the center speaker than the front
speakers, you can set the center delay time to improve the
surround sound effect.
Options: OFF (default setting), 1ms, 2ms, 3ms, 5ms.
-
Rear Delay
If the listening position is closer to the rear surround speakers than
the front speakers, you can set the rear delay time to improve the
surround sound effect.
Options: OFF (default setting), 3ms, 6ms, 9ms, 12ms, 15ms.
-
Test Tone (Disc mode only)
If set to ON, the system will test the speaker setting. The test signal
is generated through the left, center, right and surround speaker.
The default setting is OFF.
* TV System
Allows you to select the color system matching the connected
TV set.
AUTO
If the connected TV is multi system, select this mode. The
output format will be in accordance with the video signal of the
disc.
9
Special Functions
Setting the Language
3.
1.
2.
Audio
Subtitle
Disc Menu
This is to select the audio language, subtitle language and the
language used on TV screen menus or DVD menus that will
always be used for every disc to be playback. The default
setting is English.
If the language selected is not available on the disc, the original
language designated by each disc will be selected.
Setting the Features
-
Parental
Enables setting of playback limitation level. Some DVDs may
have a parental level assigned to the complete disc or to
certain scenes on the disc. The rating levels are from 1 to 8 and
are country dependent. You can prohibit the playing of certain
disc that are not suitable for your children or have certain discs
played with alternative scenes.
1.
Enter the 4-digit code. If necessary enter the code a second
time.
2.
Use
10
/
keys to select a rating level.
Press OK to confirm.
The default setting is 1G.
Rating 1 to 8
If the player’s parental level is set below 8, only disc with a lower or
equal level will be play. For example, if the player is set to 5, only discs
with ratings of 5, 4, 3, 2, and 1 will be played. Higher rated scenes will
not be played unless an alternative that has the same rating or lower is
available on the disc. For example, consider a disc that general is
suitable for most audiences, and it is rated at level 2 for the most part.
However, in the middle there are also scenes rated at 5 (not suitable for
children).
Note
Some DVDs are not encoded with a rating though the movie rating is
printed on the disc jacket. The rating level feature does not work for
such discs.
-
Password
To select a new password for the parental control or to change the
password. The password supplied as default is 1234.
-
Menu Language
Select the language for on screen display.
-
Defaults
If RESET is selected, all the items in the setup menu will be reset
to default setting, except parantal setting.
Special Functions
Special DVD / VCD features
A number of operations can be carried out directly via the multiple
menu bars on the TV screen without interrupting the disc playback.
Display the disc information
during the playback.
Select
from the menu bar and press
following display information:
From the left,
SETUP
SEARCH
SUBTITLE
LANGUAGE
STATUS
CHAPTER SEARCH
TIME SEARCH
key to select the
TITLE
P
From the left,
A-B
PBC ON/OFF
SLEEP
PROGRAM
VSS
DIMMER
Note
Some operations may be different or restricted, depending on the
disc format. Refer to the jacket or case of the disc you are playing.
1
2
3
4
5
Press MENU.
The menu bar will display across the top of the TV screen.
Press
/
to move through the menu bar.
Press
to select the highlighted icon and use
/
keys
to select your preferred option.
Press OK to confirm a highlighted selection.
To exit, press MENU or OK.
Moving to another title/chapter
Some disc may contain more than one title or chapter. If the disc has a
title or chapter menu recorded on it, you can start playback from the
selected item.
1
Select
(title) or
(chapter) from the menu bar.
Changing Subtitle Language
2
Use number keyed (0~9) to select a desire title / chapter number
and press OK to start playback.
This operation works only on DVDs with multiple soundtrack
language.
Select
from the menu bar and press
key to select the
desired language.
Note
Selecting a title or chapter might not be possible on certain discs.
Playback from a selected point
Changing Soundtrack Language
This function allows you to start playing at any chosen time on the
disc.
This operation work only on DVDs with multiple soundtrack
language.
Select
from the menu bar and press
desired language.
key to select the
For VCD:
Press
key to select the desired audio channels for sound:
LEFT VOCAL
RIGHT VOCAL
MONO LEFT
MONO
RIGHT
STEREO
LEFT VOCAL
For CD:
Press
key to select the desired audio channels for sound:
MONO LEFT
MONO RIGHT
STEREO
MONO
LEFT
Note
When the desired language is not selected even after pressing the
button several times, it means the language is not available on the
disc.
1
Select
from the menu bar.
2
Enter hours, minutes and seconds from left to right in the time edit
box using the number keys (0~9).
Each time an item has been entered, the next item will be
highlighted.
3 Press
key again to OFF, but press
to function message.
key again to display go
Note
Selecting a title or chapter might not be possible on certain discs.
11
Special Functions
Repeat A - B
This function can play a specific section in a chapter / track repeatly.
Selecting the surround sound
mode
Select
from the menu bar and press
select desire surround sound mode.
STEREO
A-B
1
2
3
Select
from the menu bar and press
key to the
starting portion that you want.
Press
key again at the end portion that you want. The
specific section will now repeat continuously.
Press
key the third time to cancel this function.
-
Note:
The A-B can be set only within the same chapter/track.
Playback Control (PBC)
PBC playback allows you to play Video Cds interactively, following
the menu on the display.
VSS
PROLOGIC
key repeatedly to
STEREO
...
Stereo
All sound is reproduced and played through the left and right
speakers. This enable standard stereo reproduction.
VSS (Virtual Surround Sound)
The ProLogic MPEG or Dolby Digital surround channel is
processed by a “virtualiser” DSP to add surround effect from
just the two front speakers.
Dolby ProLogic Surround
The Dolby ProLogic Surround system is a specially encoded
two channel analogue format that will produce sound through
four speaker channels (front left, center, front right, mono
surround) when a Dolby ProLogic Decoder is used. It is also
compatible with stereo systems but the user will stereo system
but the user will only have two channels (front left and right of
sound).
Dimming the display screen
1
Select
from the menu bar and press
key to select
different levels of brightness for the display screen: HIGH, MID
or LOW.
Sleep timer setting
-
Select
in the menu bar and press
ON or PBC OFF.
key to select PBC
When playing a disc with PBC function
Select
in the menu bar and press
key to select PBC
ON or PBC OFF.
If “PBC OFF”, press play key and the system will start playback
automatically.
If “PBC ON”, the PBC menu (if available) will appear on the TV
screen for selection. Use the number keys (0~9) to enter your
choice.
Note
If PBC mode is switched on, TIME SEARCH and REPEAT functions
are not available.
Program play
You can play the contents of the disc in the order you want by
programming the order of the tracks to be played. Up to 99 tracks
can be stored.
1 Select
in the menu bar and press
key to enter
program mode.
“
” is displayed.
2
3
4
5
6
12
Use the number keys (0~9) to input the track number in the
order you want.
” is
If you attempt to program more than 99 tracks, “
displayed.
Press OK to store the track.
To start program play, press
.
To stop play back, press
once.
To cancel the program, press
again.
The sleep timer enables the system to switch to standby mode
automatically at a present time.
1
2
-
Select
from the menu bar and press
key repeatedly to
select a present time.
The selections are as follows (time in minutes).
15
30
45
60
90
120
OFF
15...
To cancel the sleep timer
Press
key repeatedly until the “OFF” appears.
Care and Maintenance
Cleaning the components
Before cleaning, switch off the DVD receiver. Clean all components
using a wet cloth or a title synthetic cleaner.
Solvent, spirits, dilutents, etc, can damage the surface of the
device.
Notes about compact disc
(DVD, VCD, Audio CD, MP3 CD)
Always keep the CD in its cover and touch the edges only. The
surface shimmering in rainbow color must not be touched and
should always be kept clean. Do not stick paper or adhesive tape
onto the labeled side of the CD. Keep the CD away from direct
sunlight and heat sources.
A CD must also never be left in a car parked in direct sunlight as the
temperature inside the car gets very high. Clean the CD with a cloth
before playing it. Do not use any solvents such as petrol, dilutions
or other detergents to clean.
Clean the CD in a straight line from the center outwards.
Never clean the CD using circular cleaning movements.
Notes about the CD Player
If the CD player is not being used, the CD tray should always
remain closed to protect the mechanism against dust. However, it is
still possible that the lens become dirty from dust or is covered by a
thin, hardly visible film. The CD system is then no longer able to
scan the inserted CD. In this case, you need to have the lens
cleaned by a technician.
13
Maintenance
Electronic components are subject to a natural aging process. The
mechanical parts are subject to normal wear. Dust particles inside
the device may also cause faults to occur, e.g. due to dirtying of the
laser lens. Consult your authorised dealer in the case of any faults.
For transporting the set use the original packing only.
Caution!
The device is powered by dangerous voltage. The set may
therefore be opened by authorised specialists only. All maintenance
and service work must be carried out by authorised companies only.
Inexpert repair work may endanger the operator’s life.
Any work on the set done by non-authorised persons on their own
account cause the guarantee to expire.
Note
To help identify the device in case of after-sale service, always
mention the number of the ID on the inscription plate on the rear of
the device.
Troubleshooting
If you experience any of the following difficulties while using the
system, use this troubleshooting guide to help you remedy the
problem. Should any problem persist, consult your nearest service
center.
No power
l Is the power cord firmly plugged into the power outlet?
l One of the safety mechanisms may be operating. In this event,
unplug the player from the power outlet briefly and then plug it
in again.
No picture
l Check that the system is connected securely.
l The video connecting cord is damaged. Replace it with a new
one.
l Make sure you connect the system to video input connector on
the TV.
l Make sure you turn on the TV.
Make sure you select the video input on the TV so that you can
view the pictures from this system.
The picture noise appears
l Clear the disc.
l If video from this system has to go through your VCR to get to
your TV, the copy-protection applied to some DVD programs
could affect picture quality. If you still experience problems after
checking your connections, please try connecting your DVD
system directly to your TV S-Video input, if your TV is equipped
with this input.
No color in the picture
l The disc format is not according to the Td (PAL/NTSC)
l Ensure DVD player is not connected through VCR.
Severe hum or noise is hear
l Check that the speaker and components are connected
securely.
l Check that the connecting cords are away from a transformer
or motor, and at least 3 meters away from a TV set or
fluorescent light.
l Move your TV away from the audio components.
l The plugs and jacks are dirty. Wipe them with a cloth slightly
moistened with alcohol.
l Clear the disc.
The Language for the subtitle cannot be changed when you
play a DVD
l Multilingual subtitles are not recorded on DVD.
Changing the language for the subtitles is prohibited on the
DVD.
The subtitles cannot be turned off when you play a DVD
l Depending on the DVD, you may not be able to turn the
subtitles off.
The angles cannot be changed when you play a DVD
l multi-angle are not recorded on the DVD.
l Change the angles when the angle mark appears on the TV
screen.
l Changing the angles is prohibited on the DVD.
The system does not operate properly
l Static electricity, etc., may affect the system’s operation.
Press the POWER button to turn off, then press again to turn
on.
14
Electrical Specification
DVD Player
Pickup .............................................................................................................
Signal system .................................................................................................
Video signal horizontal resolution ...................................................................
Video signal-to-noise ratio ..............................................................................
Audio frequency response (at 2 CH stereo mode) .........................................
........................................................................................................................
Audio signal-to-noise ratio ..............................................................................
Dynamic range ...............................................................................................
Semiconductor laser, wavelength 650mm
NTSC/PAL
480 lines (DVD)
50 dB (DVD)
DVD (PCM): 20Hz ~ 20kHz (+/- 3.0 dB)
CD: 20Hz~20kHz (+/- 3.0dB)
60dB
DVD: 80dB; CD: 80dB
Video Output
VBS Video ......................................................................................................
S-video ...........................................................................................................
........................................................................................................................
Scart out .........................................................................................................
2 Vp-p 75ohms
Y: 1 Vp-p 75 ohms
C: PAL 0.3 Vp-p 75 ohms / NTSC 0.286 Vp-p 75 ohms
1 Vp-p 75 ohms
Audio Line Output
Audio. L/R ....................................................................................................... 1 Vrms, 1k ohms
Optical & Coaxial out ...................................................................................... 1 Vp-p 75 ohms
Main unit
Power supply ..................................................................................................
Power Consumption .......................................................................................
Dimensions .....................................................................................................
Weight ............................................................................................................
110-240V AC, 50Hz
15W maximum
W430 x H48 x D250mm
4kg
Operation temperature ................................................................................... 5oC~35oC
Operation Humidity ......................................................................................... 15~75%
Design and specifications are subjected to change without notice. Weight and dimensions are approximate.
15
Download PDF