advertisement
LFD DISPLAY
User Manual
ED65D ED75D
The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Table of contents
Before Using the Product
Preparations
Assembling the Holder-Wire stand
Before Installing the Product (Installation
Wall Mount Kit Specifications (VESA)
Connecting and Using a Source
Device
Connection using the D-SUB cable (Analog type) 37
Connection using a DVI cable (Digital type) 38
Connection Using an HDMI-DVI Cable 38
Connection Using an HDMI Cable 39
Connection Using the component Cable
Connection Using an HDMI-DVI Cable
Connection Using an HDMI Cable
Connecting to an Audio System 42
Using MDC
Configuring Settings for Multi Control 43
Configuring settings for Multi Control 43
MDC Program Installation/Uninstallation 44
Using MDC via RS-232C (serial data communications standards) 45
Screen Adjustment
If the input source is PC, DVI, HDMI(PC) 46
If the input source is AV, Component, HDMI(AV) 46
Backlight / Contrast / Brightness / Sharpness /
2
Table of contents
Sound Adjustment
Applications
System
Configuring settings for Multi Control 65
Troubleshooting for Anynet+ 83
3
Table of contents
Support
Troubleshooting Guide
Requirements Before Contacting Samsung
Checking the Resolution and Frequency
Specifications
Appendix
Contact SAMSUNG WORLD WIDE 103
Responsibility for the Pay Service (Cost to
A Product damage caused by customer's fault 112
Optimum Picture Quality and Afterimage Burnin Prevention 113
Prevention of Afterimage Burn-in
4
Chapter 01
Before Using the Product
Copyright
The contents of this manual are subject to change without notice to improve quality.
© 2014 Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Microsoft, Windows are registered trademarks of Microsoft Corporation.
VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
Ownership of all other trademarks is attributed to their due owner.
5
Safety Precautions
Caution
RISK OF ELECTRIC SHOCK DO NOT OPEN
Caution : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. (OR BACK)
THERE ARE NO USER SERVICEABLE PARTS INSIDE.
REFER ALL SERVICING TO QUALIFIED PERSONNEL.
This symbol indicates that high voltage is present inside.
It is dangerous to make any kind of contact with any internal part of this product.
This symbol alerts you that important literature concerning operation and maintenance has been included with this product.
Symbols
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions are not followed.
Activities marked by this symbol are prohibited.
Instructions marked by this symbol must be followed.
Cleaning
― Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
― Take the following steps when cleaning.
― The following images are for reference only. Real-life situations may differ from what is shown in the images.
1 Power off the product and computer.
2 Disconnect the power cord from the product.
― Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result.
3 Wipe the product with a clean, soft and dry cloth.
• Do not use detergents that contain alcohol, solvent or surface-active agents.
!
• Do not spray water or detergent directly on the product.
4 Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the product.
5
Connect the power cord to the product when cleaning is finished.
6
Power on the product and computer.
6
Storage
High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used nearby.
― Contact Customer Service Center if the inside of the product needs cleaning (service fee will be charged).
Electricity and Safety
― The following images are for reference only. Real-life situations may differ from what is shown in the images.
Warning
Do not use a damaged power cord or plug, or a loose power socket.
• An electric shock or fire may result.
!
Do not use multiple products with a single power socket.
• Overheated power sockets may cause a fire.
Do not touch the power plug with wet hands. Otherwise, an electric shock may result.
!
Insert the power plug all the way in so it is not loose.
• An unsecure connection may cause a fire.
!
Connect the power plug to a grounded power socket (type 1 insulated devices only).
• An electric shock or injury may result.
Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy object.
• Damage to the cord may result in a fire or electric shock.
Do not place the power cord or product near heat sources.
• A fire or electric shock may result.
Clean any dust around the pins of the power plug or the power socket with a dry cloth.
• A fire may result.
7
Caution
!
!
!
Do not disconnect the power cord while the product is being used.
• The product may become damaged by an electric shock.
Only use the power cord provided with your product by Samsung. Do not use the power cord with other products.
• A fire or electric shock may result.
Keep the power socket where the power cord is connected unobstructed.
• The power cord must be disconnected to cut off power to the product when an issue occurs.
• Note that the product is not completely powered down by using only the power button on the remote.
Hold the plug when disconnecting the power cord from the power socket.
• An electric shock or fire may result.
!
Installation
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF
THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
• A fire may result.
Have a technician install the wall-mount hanger.
• Installation by an unqualified person can result in an injury.
• Only use approved cabinets.
Do not install the product in poorly ventilated spaces such as a bookcase or closet.
• An increased internal temperature may cause a fire.
Install the product at least 10cm away from the wall to allow ventilation.
• An increased internal temperature may cause a fire.
!
Keep the plastic packaging out of the reach of children.
• Children may suffocate.
!
8
!
Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)
• The product may fall and become damaged and/or cause an injury.
• Using the product in an area with excess vibration may damage the product or cause a fire.
Do not install the product in a vehicle or a place exposed to dust, moisture
(water drips, etc.), oil, or smoke.
• A fire or electric shock may result.
Caution
!
Do not expose the product to direct sunlight, heat, or a hot object such as a stove.
• The product lifespan may be reduced or a fire may result.
Do not install the product within the reach of young children.
• The product may fall and injure children.
• As the front is heavy, install the product on a flat and stable surface.
Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a kitchen or near a kitchen counter.
!
!
Do not drop the product while moving.
• Product failure or personal injury may result.
Do not set down the product on its front.
• The screen may become damaged.
When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of the product is not protruding.
• The product may fall and become damaged and/or cause an injury.
• Install the product only on cabinets or shelves of the right size.
Set down the product gently.
• Product failure or personal injury may result.
SAMSUNG
Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical substances, extreme temperatures or a significant presence of moisture, or a place where the product will operate continuously for an extended period of time) may seriously affect its performance.
• Be sure to consult Samsung Customer Service Center if you want to install the product at such a place.
9
Operation
Warning
!
!
There is a high voltage inside the product. Never disassemble, repair or modify the product yourself.
• A fire or electric shock may result.
• Contact Samsung Customer Service Center for repairs.
Before moving the product, turn off the power switch and disconnect the power cable and all other connected cables.
• Damage to the cord may result in a fire or electric shock.
If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord immediately and contact Samsung Customer
Service Center.
• An electric shock or fire may result.
Do not let children hang from the product or climb on top of it.
• Children may become injured or seriously harmed.
!
!
!
If the product is dropped or the outer case is damaged, turn off the power switch and disconnect the power cord. Then contact Samsung Customer
Service Center.
• Continued use can result in a fire or electric shock.
Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.
• The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a serious injury.
During a lightning or thunderstorm, power off the product and remove the power cable.
• A fire or electric shock may result.
Do not drop objects on the product or apply impact.
• A fire or electric shock may result.
GAS
Do not move the product by pulling the power cord or any cable.
• Product failure, an electric shock or fire may result from a damaged cable.
If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area immediately.
• Sparks can cause an explosion or fire.
Do not lift or move the product by pulling the power cord or any cable.
• Product failure, an electric shock or fire may result from a damaged cable.
10
!
100
Do not use or keep combustible spray or an inflammable substance near the product.
• An explosion or fire may result.
Caution
Ensure the vents are not blocked by tablecloths or curtains.
• An increased internal temperature may cause a fire.
!
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper, matches, etc) into the product (via the vent or input/ output ports, etc).
• Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Center.
• Product failure, an electric shock or fire may result.
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the product.
• Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Center.
• Product failure, an electric shock or fire may result.
!
!
-_-
!
Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels.
• Activate power-saving mode or a moving-picture screen saver if you will not be using the product for an extended period of time.
Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc).
• Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
Use the product at the recommended resolution and frequency.
• Your eyesight may deteriorate.
Do not hold the product upside-down or move it by holding the stand.
• The product may fall and become damaged or cause an injury.
Looking at the screen too close for an extended period of time can deteriorate your eyesight.
Do not use humidifiers or stoves around the product.
• A fire or electric shock may result.
11
!
!
!
Rest your eyes for more than 5 minutes for every 1 hour of product use.
• Eye fatigue will be relieved.
Do not touch the screen when the product has been turned on for an extended period of time as it will become hot.
Store small accessories out of the reach of children.
Exercise caution when adjusting the product angle or stand height.
• Your hand or finger may get stuck and injured.
• Tilting the product at an excessive angle may cause the product to fall and an injury may result.
Do not place heavy objects on the product.
• Product failure or personal injury may result.
!
!
When using headphones or earphones, do not turn the volume too high.
• Having the sound too loud may damage your hearing.
Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach.
• If children have had the battery in their mouths, consult your doctor immediately.
When replacing the battery, insert it with the right polarity (+, -).
• Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.
Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time.
• Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.
The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.
• The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.
12
Chapter 02
Preparations
Checking the Components
Components
Contact the vendor where you purchased the product if any components are missing.
The appearance of the components and items sold separately may differ from the image shown.
A stand is not provided with the product.
To install a stand, you can purchase one separately.
Components may differ in different locations.
Quick setup guide Warranty card
(Not available in some locations)
Remote Control (
(AA59-00714A)
-
+
+
Batteries (
(Not available in some locations)
D-SUB cable (
)
Holder-Wire stand
Power cord
Holder-Ring (4EA)
RS232C(IN) adapter
13
Items sold separately
Wall-mount Kit HDMI cable (
HDMI-DVI cable (
) PIM
RS232C-Stereo cable RS232C(OUT) adapter Component cable (
DVI cable (
)
14
Parts
Panel Key
RGB / DVI /
HDMI / AV /
AUDIO IN
DVI IN
Power on the product.
If you press the [ ] button when the product is turned on, the control menu will be displayed.
To exit the OSD menu, press and hold the panel key for at least one second.
Move to the upper or lower menu. You can also adjust the value of an option.
Move to the left or right menu.
You can adjust the volume by moving the panel key left or right when the control menu is not displayed.
15
Reverse Side
HDMI / AV /
AUDIO IN
DVI IN
RGB / DVI /
HDMI / AV /
COMPONENT
AUDIO IN
DVI IN
PIM
Port
HDMI IN
SERVICE (5V 0.5A)
EXTERNAL IR / AMBIENT SENSOR IN
RGB IN
DVI IN
AUDIO OUT
RGB / DVI / HDMI / AV / COMPONENT
AUDIO IN
RS232C IN
RS232C OUT
PIM
COMPONENT / AV IN
Description
Connects to a source device using an HDMI cable.
This port is used to upgrade the software.
Supplies power to the External ambient sensor board or receives the light sensor signal.
External ambient sensor: Sold separately
Connects to a source device using a D-SUB cable.
Connects to a source device using a DVI cable or HDMI-DVI cable.
Connects to the audio of a source device.
Connect to audio input using an audio cable.
Connects to MDC using an RS232C-stereo adapter.
Connects to a PIM. (Refer to the PIM user manual for details.)
Connects to a source device using the Component/AV cable.
16
External sensor KIT
― The External sensor KIT has a remote-control sensor, a brightness sensor and function keys. If mounting the display onto a wall, you can move the External sensor KIT to the side of the display.
― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
HDMI / AV /
AUDIO IN
DVI IN
Buttons
Remote Control
Sensor
Light sensor
Power indicator
SOURCE button
POWER button
Description
Aim the remote control towards this spot on the LCD Display.
― Keep the area between the remote sensor and remote control obstacle-free.
Use the remote control within 7m to 10m from the sensor on the product at an angle of 30 from the left and right.
― Store used batteries out of reach of children and recycle.
― Do not use a new and used battery together. Replace both batteries at the same time.
― Remove batteries when the remote control is not to be used for an extended period of time.
Automatically detects the intensity of ambient light around a selected display and adjusts the screen brightness.
Turns off in power-on mode and blinks green in power-saving mode.
Switches from PC mode to Video mode.
Selects the input source that an external device is connected to.
Use this button for turning the LCD Display on and off.
17
Attaching the External sensor KIT to the side
― This External sensor KIT can be attached to any part of the display using the double-sided tape provided with the sensor.
― The External sensor KIT can also be attached to a wall near the display.
― Do not attach the External sensor KIT to the display if the display does not have plastic or metal sides. The display can be damaged.
18
Assembling the Holder-Wire stand Anti-theft Lock
― An anti-theft lock allows you to use the product securely even in public places.
― The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
To lock an anti-theft locking device:
― Stand: Sold separately
1 Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2 Put one end of the cable through the loop on the other end.
3 Insert the locking device into the anti-theft lock slot at the back of the product.
4 Lock the locking device.
An anti-theft locking device can be purchased separately.
Refer to the user guide provided with your anti-theft locking device for details.
Anti-theft locking devices can be purchased at electronics retailers or online.
19
Remote Control
― Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.
― A button without a description in the image below is not supported on the product.
Power on the product.
Adjust the volume.
.QZ
1
GHI
4
PRS
7
DEL-/--
VOL
ABC
2
JKL
5
TUV
8
SYMBOL
0
CONTENT
(HOME)
SOURCE
OFF
DEF
3
MNO
6
WXY
9
MUTE
CH
MagicInfo
Lite/S
MENU
BLANK
Power off the product.
Enter the password in the OSD menu.
Mute the sound.
Unmuting the sound: Press MUTE again or press the volume control (+ VOL -) button.
Select a connected source device.
Display or hide the onscreen display menu, or return to the previous menu.
Remote control button functions may differ for different products.
20
TOOLS INFO
Quickly select frequently used functions.
Return to the previous menu.
RETURN EXIT
PC
A
MAGICINFO
DVI
B
3D
HDMI
C
LOCK
DP
D
Display information on the screen.
Move to the upper, lower, left or right menu, or adjust an option's setting.
Confirm a menu selection.
Exit the current menu.
Manually select a connected input source from
PC , DVI , HDMI .
It sets safe lock function.
Remote control button functions may differ for different products.
To place batteries in the remote control
21
Before Installing the Product
(Installation Guide)
15 ˚
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
• Ensure that an authorized installation company installs the wall mount.
• Otherwise, it may fall and cause personal injury.
• Make sure to install the specified wall mount.
Tilting Angle and Rotation
― Contact Samsung Customer Service Center for further details.
• The product can be tilted at a maximum angle of 15 from a perpendicular wall surface.
• To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.
Ventilation
Installation on a Perpendicular Wall
A Minimum 40 mm
B Ambient temperature: Under 35 C
• When installing the product on a perpendicular wall, allow at least 40 mm of space between the product and wall surface for ventilation and ensure that the ambient A temperature is kept below 35 C.
A
B
Figure 1.1 Side view
22
B
A
E
C
Figure 1.2 Side view
Dimensions
2
1
Figure 1.3 Side view
D
4
3
D
Installation on an Indented Wall
― Contact Samsung Customer Service Center for further details.
Plane view
A Minimum 40 mm
B Minimum 70 mm
C Minimum 50 mm
D Minimum 50 mm
E Ambient temperature: Under 35 C
― When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 C.
5
Model name
1
1467.5 (57.8)
1 2
1431.4 (56.4)
2 3
806.5 (31.8)
3 4
848.0 (33.4)
4 5
Unit: mm (inches)
65.0 (2.6) ED65D
ED75D 1675.0 (65.9) 1653.3 (65.1) 931.3 (36.7) 958.5 (37.7) 65.0 (2.6)
― All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice.
Refer to the dimensions prior to performing installation of your product. Not responsible for typographical or printed errors.
23
Installing the Wall Mount
Installing the Wall Mount Kit
The wall mount kit (sold separately) allows you to mount the product on the wall.
For detailed information on installing the wall mount, see the instructions provided with the wall mount.
We recommend you contact a technician for assistance when installing the wall mount bracket.
Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.
24
Wall Mount Kit Specifications (VESA)
― Install your wall mount on a solid wall perpendicular to the floor. Before attaching the wall mount to surfaces other than plaster board, please contact your nearest dealer for additional information.
If you install the product on a slanted wall, it may fall and result in severe personal injury.
• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.
• Do not use screws that are longer than the standard length or do not comply with the VESA standard screw specifications. Screws that are too long may cause damage to the inside of the product.
• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on the wall mount specifications.
• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
• Do not mount the product at more than a 15 degree tilt.
• Always have two people mount the product on a wall.
• Standard dimensions for wall mount kits are shown in the table below.
Unit: mm (inches)
Model name VESA screw hole specs (A * B) in millimeters
Standard Screw Quantity
ED65D 400 x 400 (15.7 × 15.7) M8, L32 4 EA
ED75D
― Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.
25
Remote Control (RS232C)
Cable Connection
RS232C Cable
Interface
Pin
Bit rate
Data bits
Parity
Stop bit
Flow control
Maximum length
RS232C (9 pins)
TxD (No.2), RxD (No.3), GND (No.5)
9600 bps
8 bit
None
1 bit
None
15 m (only shielded type)
• Pin assignment
1 2 3 4 5
6
7
8
9
3
4
5
Pin
1
2
6 7 8 9
Signal
Detect data carrier
Received data
Transmitted data
Prepare data terminal
Signal ground
Prepare data set
Send request
Clear to send
Ring indicator
26
• RS232C cable
Connector: 9-Pin D-Sub to Stereo Cable
9 5
6
-P1-
1
-P1-
Female Rx
Tx
Gnd
-P1-
2
3
5
-------->
<--------
----------
-P2-
3
2
5
Tx
Rx
Gnd
-P2-
STEREO
PLUG
(3.5ø)
3
2
1
-P2-
Connection
• Connection 1
IN
RS232C
OUT IN
RS232C
OUT IN
RS232C
OUT IN
RS232C
OUT
27
Control Codes
Viewing control state (Get control command)
Header Command ID Data length Checksum
0xAA Command type 0
Controlling (Set control command)
Header Command ID Data length
0xAA Command type 1
8
9
5
6
7
2
3
4
Command
No.
Command type
1 Power control
Volume control
Input source control
Screen mode control
Screen size control
PIP on/off control
Auto adjustment control (PC and
BNC only)
Video wall mode control
Safety Lock
Command
0x11
0x12
0x14
0x18
0x19
0x3C
0x3D
0x5C
0x5D
Data
Value
0~1
0~1
Checksum
Value range
0~1
-
-
0~100
0~255
0~1
0
No.
10
11
Command type
Video Wall On
Video Wall User Control
Command
0x84
0x89
Value range
-
0~1
• All communications take place in hexadecimals. The checksum is calculated by adding up all values except the header. If a checksum adds up to be more than 2 digits as shown below
(11+FF+01+01=112), the first digit is removed.
E.g. Power On & ID=0
Header
0xAA
Command
0x11
ID Data length
1
Data 1
"Power"
Checksum
Header
0xAA
Command
0x11
ID Data length
1
Data 1
1
12
• To control all devices connected by a serial cable simultaneously irrespective of IDs, set the ID as
"0xFE" and transmit commands. Commands will be executed by each device but ACK will not respond.
28
Power control
• Function
A product can be powered on and off using a PC.
• Viewing power state (Get Power ON / OFF Status)
Header Command ID Data length
0xAA 0x11 0
Checksum
• Setting power ON/Off (Set Power ON / OFF)
Header Command ID Data length
0xAA 0x11 1
"Power": Power code to be set on a product.
1: Power ON
0: Power OFF
• Ack
Header Command ID Data length
0xAA 0xFF 3
Ack/Nak
'A'
Data
"Power" r-CMD
0x11
"Power": Power code to be set on a product.
• Nak
Header Command ID Data length
0xAA 0xFF 3
"ERR" : A code showing what error has occurred.
Ack/Nak
'N' r-CMD
0x11
Checksum
Val1
"Power"
Checksum
Val1
"ERR"
Checksum
Volume control
• Function
The volume of a product can be adjusted using a PC.
• Viewing volume state (Get Volume Status)
Header Command ID Data length
0xAA 0x12 0
Checksum
• Setting the volume (Set Volume)
Header Command ID
0xAA 0x12
Data length
1
"Volume": Volume value code to be set on a product. (0-100)
• Ack
Header Command ID Data length Ack/Nak
0xAA 0xFF 3 'A'
Data
"Volume" r-CMD
0x12
"Volume": Volume value code to be set on a product. (0-100)
• Nak
Header Command ID Data length Ack/Nak
0xAA 0xFF 3 'N'
"ERR" : A code showing what error has occurred.
r-CMD
0x12
Val1
"ERR"
Checksum
Val1
"Volume"
Checksum
Checksum
29
Input source control
• Function
The input source of a product can be changed using a PC.
• Viewing input source state (Get Input Source Status)
Header Command ID Data length Checksum
0xAA 0x14 0
• Setting the input source (Set Input Source)
Header Command ID Data length
0xAA 0x14 1
Data
"Input Source"
Checksum
"Input Source": An input source code to be set on a product.
0x14 PC
0x1F
0x30
0x40
0x21
0x18
0x0C
0x08
0x20
DVI
Input source
Component
MagicInfo
DVI_video
RF(TV)
DTV
HDMI
0x22 HDMI_PC
― DVI_video, HDMI_PC cannot be used with the Set command. They only respond to "Get" commands.
― This model does not support HDMI, HDMI_PC ports.
― MagicInfo is only available with models that contain the MagicInfo function.
― RF(TV), DTV are only available with models that include a TV.
• Ack
Header Command ID Data length Ack/Nak r-CMD Val1
0xAA 0xFF 3 'A' 0x14 "Input
Source"
"Input Source": An input source code to be set on a product.
• Nak
Header Command ID Data length Ack/Nak
0xAA 0xFF 3 'N'
"ERR" : A code showing what error has occurred.
r-CMD
0x14
Val1
"ERR"
Checksum
Checksum
30
Screen mode control
• Function
The screen mode of a product can be changed using a PC.
Screen mode cannot be controlled when the Video Wall function is enabled.
― This control can only be used on models that include a TV.
• Viewing screen status (Get Screen Mode Status)
Header Command ID Data length Checksum
0xAA 0x18 0
• Setting the picture size (Set Picture Size)
Header Command ID Data length
0xAA 0x18 1
"Screen Mode": A code that sets the product status
0x01 16 : 9
0x04
0x31
0x0B
Zoom
Wide Zoom
4 : 3
• Ack
Header
0xAA
Command
0xFF
ID
Data
"Screen Mode"
Data length Ack/Nak
3 'A' r-CMD
0x18
Checksum
Val1
"Screen
Mode"
"Screen Mode": A code that sets the product status
Checksum
• Nak
Header
0xAA
Command
0xFF
ID Data length Ack/Nak
3 'N' r-CMD
0x18
Val1
"ERR"
"ERR": A code showing what error has occurred
Screen size control
• Function
The screen size of a product can be changed using a PC.
• Viewing the screen size (Get Screen Size Status)
Header Command ID Data length Checksum
0xAA 0x19 0
• Ack
Header Command ID Ack/Nak r-CMD
0xAA 0xFF
Data length
3 'A' 0x19
Val1
"Screen Size"
"Screen Size": product screen size (range: 0 – 255, unit: inch)
• Nak
Header Command ID Data length
Ack/Nak r-CMD
0xAA 0xFF 3 'N' 0x19
"ERR": A code showing what error has occurred
Val1
"ERR"
Checksum
Checksum
Checksum
31
PIP On/Off control
• Function
The PIP mode of a product can be turned on or off using a PC.
― Only available on models that have the PIP function.
― The mode cannot be controlled if Video Wall is set to On .
― This function is not available in MagicInfo .
• Viewing PIP on/off state (Get the PIP ON / OFF Status)
Header Command ID Data length Checksum
0xAA 0x3C 0
• Setting PIP on/off (Set the PIP ON / OFF)
Header Command ID Data length
0xAA 0x3C 1
Data
"PIP"
"PIP": A code used to turn the PIP mode of a product on or off
1: PIP ON
0: PIP OFF
• Ack
Header Command ID Data length
Ack/Nak r-CMD
0xAA 0xFF 3 'A' 0x3C
"PIP": A code used to turn the PIP mode of a product on or off
• Nak
Header Command ID Data length
Ack/Nak r-CMD
0xAA 0xFF 3 'A' 0x3C
Val1
"PIP"
Val1
"PIP"
Checksum
Checksum
Checksum
"ERR": A code showing what error has occurred
Auto adjustment control (PC and BNC only)
• Function
Automatically adjust the PC system screen using a PC.
• Viewing auto adjustment state (Get Auto Adjustment Status)
None
• Setting auto adjustment (Set Auto Adjustment)
Header Command ID Data length Data
0xAA 0x3D 1 "Auto
Adjustment"
"Auto Adjustment" : 0x00 (at all times)
• Ack
Header Command ID Data length
0xAA 0xFF 3
Ack/Nak
'A' r-CMD
0x3D
Val1
Checksum
"Auto
Adjustment"
Checksum
• Nak
Header Command ID Data length
3 0xAA 0xFF
"ERR": A code showing what error has occurred
Ack/Nak
'A' r-CMD
0x3D
Val1
"ERR"
Checksum
32
Video Wall Mode Control
• Function
Video Wall mode can be activated on a product using a PC.
This control is only available on a product whose Video Wall is enabled.
• Viewing video wall mode (Get Video Wall Mode)
Header Command ID Data length Checksum
0xAA 0x5C 0
• Setting the video wall (Set Video Wall Mode)
Header Command ID Data length
0xAA 0x5C 1
Data
"Video Wall Mode"
"Video Wall Mode": A code used to activate Video Wall mode on a product
1: Full
0: Natural
• Ack
Header Command ID Data length
Ack/Nak r-CMD Val1
0xAA 0xFF 3 'A' 0x5C "Video Wall
Mode"
"Video Wall Mode": A code used to activate Video Wall mode on a product
• Nak
Header Command ID Data length
Ack/Nak r-CMD Val1
0xAA 0xFF 3 'A' 0x5C "ERR"
"ERR": A code showing what error has occurred
Checksum
Checksum
Checksum
Safety Lock
• Function
PC can be used to turn the Safety Lock function on or off on a product.
This control is available regardless of whether or not the power is turned on.
• Viewing the safety lock state (Get Safety Lock Status)
Header Command ID Data length Checksum
0xAA 0x5D 0
• Enabling or disabling safety lock (Set Safety Lock Enable / Disable)
Header Command ID Data length Data
0xAA 0x5D 1 "Safety Lock"
"Safety Lock": Safety lock code to be set on a product
1: ON
0: OFF
• Ack
Header Command ID Data length
Ack/Nak
0xAA 0xFF 3 'A' r-CMD
0x5D
Val1
Checksum
"Safety Lock"
"Safety Lock": Safety lock code to be set on a product
• Nak
Header Command ID Data length
Ack/Nak
0xAA 0xFF 3
"ERR": A code showing what error has occurred
'N' r-CMD
0x5D
Val1
"ERR"
Checksum
Checksum
33
Video Wall On
• Function
Turn Video Wall on or off on the product from your computer.
• Get Video Wall On/Off Status
Header Command ID Data length Checksum
0xAA 0x84 0
• Set Video Wall On/Off
Header Command
0xAA 0x84
ID Data length
1
Data
V.Wall_On
• V.Wall_On: Video Wall code to be assigned to the product
1: Video Wall ON
0: Video Wall OFF
• Ack
Header Command ID Data length Ack/Nak
0xAA 0xFF 3 'A' r-CMD
0x84
Checksum
Val1
V.Wall_
On
Checksum
V.Wall_On : Same as above
• Nak
Header
0xAA
Command
0xFF
ID Data length Ack/Nak
3 'N' r-CMD
0x84
Val1
ERR
"ERR": A code showing what error has occurred
Video Wall User Control
• Function
Turn the Video Wall function on or off on the product from your computer.
• Get Video Wall Status
Header Command ID Data length Checksum
0xAA 0x89 0
• Set Video Wall
Header
0xAA
Command
0x89
ID Data length
2
Wall_Div: Video Wall Divider code assigned to the product
Val1
Wall_Div
Val2
Wall_SNo
Checksum
Checksum
34
10x10 Video Wall Model
Off
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F
0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F
0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F
0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F
0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F
0x61 0x62 0x63 0x64 0x65 0x66 0x67 0x68 0x69 0x6A 0x6B 0x6C 0x6D 0x6E 0x6F
0x71 0x72 0x73 0x74 0x75 0x76 0x77 0x78 0x79 0x7A 0x7B 0x7C 0x7D 0x7E N/A
0x81 0x82 0x83 0x84 0x85 0x86 0x87 0x88 0x89 0x8A 0x8B 0x8C N/A N/A N/A
0x91 0x92 0x93 0x94 0x95 0x96 0x97 0x98 0x99 0x9A 0x9B N/A N/A N/A N/A
0xA1 0xA2 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAA N/A N/A N/A N/A N/A
0xB1 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 0xB8 0xB9 N/A N/A N/A N/A N/A N/A
0xC1 0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC8 N/A N/A N/A N/A N/A N/A N/A
0xD1 0xD2 0xD3 0xD4 0xD5 0xD6 0xD7 N/A N/A N/A N/A N/A N/A N/A N/A
0xE1 0xE2 0xE3 0xE4 0xE5 0xE6 0xE7 N/A N/A N/A N/A N/A N/A N/A N/A
0xF1 0xF2 0xF3 0xF4 0xF5 0xF6 N/A N/A N/A N/A N/A N/A N/A N/A N/A
35
...
99
1
2
100
Wall_SNo: Product Number code assigned to the product
10x10 Video Wall Model : ( 1 ~ 100)
Set Number Data
0x01
0x02
...
0x63
0x64
• Ack
Header
0xAA
Command
0xFF
ID Data length
4
• Nak
Header Command
0xFF
ID Data length
3 0xAA
"ERR": A code showing what error has occurred
Ack/Nak
'A'
Ack/Nak
'N' r-CMD
0x89 r-CMD
0x89
Val1
ERR
Val1
Wall_Div
Val2
Wall_SNo
Checksum
Checksum
36
Chapter 03
Connecting and Using a Source Device
Before Connecting
Check the following before you connect this product with other devices. Devices that can be connected to this product include PCs, camcorders, speakers, set top boxes and DVD/Blu-ray Disc players.
Pre-connection Checkpoints
― Before connecting a source device, read the user manual provided with it.
The number and locations of ports on source devices may differ from device to device.
― Do not connect the power cable until all connections are completed.
Connecting the power cable during connection may damage the product.
― Check the types of ports at the back of the product you want to connect.
Connecting to a PC
• Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
• A PC can be connected to the product in a variety of ways.
Select a connection method suitable for your PC.
― Connecting parts may differ in different products.
Connection using the D-SUB cable (Analog type)
RGB / DVI /
COMPONENT
DVI IN
RGB IN
RGB / DVI / HDMI / AV / COMPONENT
AUDIO IN
37
Connection using a DVI cable (Digital type)
HDMI / AV /
AUDIO IN
DVI IN
DVI IN
RGB / DVI / HDMI / AV / COMPONENT
AUDIO IN
Connection Using an HDMI-DVI Cable
― When you connect a PC to the product using an HDMI-DVI cable, set Edit Name to DVI PC to access video and audio content stored on the PC.
HDMI IN
HDMI / AV /
AUDIO IN
DVI IN
RGB / DVI / HDMI / AV / COMPONENT
AUDIO IN
38
Connection Using an HDMI Cable
HDMI IN
HDMI / AV /
AUDIO IN
DVI IN
39
Connecting to a Video Device
• Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
• You can connect a video device to the product using a cable.
― Connecting parts may differ in different products.
― Press the SOURCE button on the remote control to change the source.
Connection Using an AV Cable
RGB / DVI /
COMPONENT HDMI / AV / AUDIO IN
DVI IN
COMPONENT / AV IN
RGB / DVI / HDMI / AV / COMPONENT
AUDIO IN
Connection Using the component Cable
RGB / DVI /
COMPONENT HDMI / AV / AUDIO IN
DVI IN
COMPONENT / AV IN
RGB / DVI / HDMI / AV / COMPONENT
AUDIO IN
40
Connection Using an HDMI-DVI Cable
― Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. To resolve this, additionally connect an audio cable to the audio ports on the product and video device.
When you connect a video device to the product using an HDMI-DVI cable, set Edit Name to DVI
Devices to access video and audio content stored on the video device.
― Supported resolutions include 1080p (50/60Hz), 720p (50/60Hz), 480p, and 576p.
HDMI IN
RGB / DVI /
COMPONENT HDMI / AV / AUDIO IN
DVI IN
Connection Using an HDMI Cable
Using an HDMI cable or HDMI to DVI Cable (up to 1080p)
• For better picture and audio quality, connect to a digital device using an HDMI cable.
• An HDMI cable supports digital video and audio signals, and does not require an audio cable.
To connect the product to a digital device that does not support HDMI output, use an HDMI-DVI and audio cables.
• The picture may not display normally (if at all) or the audio may not work if an external device that uses an older version of HDMI mode is connected to the product. If such a problem occurs, ask the manufacturer of the external device about the HDMI version and, if out of date, request an upgrade.
• Be sure to purchase a certified HDMI cable. Otherwise, the picture may not display or a connection error may occur.
• A basic high-speed HDMI cable or one with ethernet is recommended.
This product does not support the ethernet function via HDMI.
RGB / DVI / HDMI / AV / COMPONENT
AUDIO IN
HDMI IN
HDMI / AV / RGB / DVI /
AUDIO IN COMPONENT
DVI IN
41
Connecting to an Audio System
― Connecting parts may differ in different products.
RGB / DVI /
COMPONENT HDMI / AV / AUDIO IN
DVI IN
AUDIO OUT
Changing the Input source
― The displayed image may differ depending on the model.
Source
HDMI
PC
HDMI-CEC
BD Player
AV Component PC DVI
----
Source
MENU m : T Source List ENTER
Source allows you to select a variety of sources and change source device names.
You can display the screen of a source device connected to the product. Select a source from source list to display the screen of the selected source.
― The input source can also be changed by using the SOURCE button on the remote control.
― The screen may not display correctly if an incorrect source is selected for the source device you want to convert to.
42
Chapter 04
Using MDC
MDC (Multiple Display Control) is an application that allows you to easily control multiple display devices simultaneously using a PC.
Configuring Settings for Multi Control
MENU m : T Multi Control ENTER
Assign an individual ID to your product.
Configuring settings for Multi Control
• ID Setup
Assign an ID to a set. (Range: 0~99)
Press to select a number, and press .
• ID Input
Enter the ID number of the product connected to the input cable for input signal reception.
Enter the number you want using the number buttons on the remote control.
43
For details on how to use the MDC program, refer to Help after installing the program. The MDC program is available on the website.
MDC installation can be affected by the graphics card, mother board and network conditions.
If the directory path is not specified, the program will be installed in the default directory path.
Select " Launch MDC Unified " and click " Finish " to run the MDC program immediately.
The MDC execution icon may not be displayed depending on the PC system or product specifications.
Press F5 if the execution icon is not displayed.
MDC Program Installation/Uninstallation
Installation
1
Click the MDC Unified installation program.
2
Select a language for installation. Next, click " OK ".
3
When the " Welcome to the InstallShield Wizard for MDC_Unified " screen appears, click " Next ".
4
In the " License Agreement " window displayed, select " I accept the terms in the license agreement " and click " Next ".
5
In the displayed " Customer Information " window, fill out all the information fields and click " Next ".
6
In the displayed " Destination Folder " window, select the directory path you want to install the program in and click " Next ".
7
In the displayed " Ready to Install the Program " window, check the directory path to install the program in and click " Install ".
8
Installation progress will be displayed.
9
Click " Finish " in the displayed " InstallShield Wizard Complete " window.
10
The MDC Unified shortcut icon will be created on the desktop after installation.
Uninstallation
1
Select Settings > Control Panel on the Start menu and double-click Add/Delete Program.
2
Select MDC Unified from the list and click Change/Remove.
44
Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously using a PC.
Connecting to MDC
Using MDC via RS-232C (serial data communications standards)
An RS-232C serial cable must be connected to the serial ports on the PC and monitor.
RS232C IN
HDMI / AV / RGB / DVI / COMPONENT
AUDIO IN
DVI IN
RS232C IN / OUT
RS232C OUT
Monitor 1
RS232C IN Monitor 2
RS232C OUT
Computer
45
Chapter 05
Screen Adjustment
Configure the Picture settings ( Backlight , Color Tone , etc.).
The layout of the Picture menu options may vary depending on the product.
Picture Mode
MENU m : T Picture Mode ENTER
Picture
Picture Mode
· Backlight
· Contrast
· Brightness
· Sharpness
· Color
· Tint (G/R)
Information
The displayed image may differ depending on the model.
Select a picture mode ( Picture Mode ) suitable for the environment where the product will be used.
Different Picture Mode options are displayed depending on the current input source.
If the input source is PC, DVI, HDMI(PC)
• Information : This mode reduces eye fatigue and is suitable for displaying information to the public.
• Advertisement : This mode is suitable for displaying video content and indoor/outdoor advertisements.
If the input source is AV, Component, HDMI(AV)
• Dynamic : This mode is suitable when the ambient light is bright.
• Standard : This mode is generally suitable for any environment.
• Natural : Suitable for reducing eye strain.
• Movie : This mode reduces eye fatigue.
46
Backlight / Contrast / Brightness /
Sharpness / Color / Tint (G/R)
MENU m : T ENTER
Picture
Picture Mode
· Backlight
· Contrast
· Brightness
· Sharpness
· Color
· Tint (G/R)
Information
Your product has several options for adjusting picture quality.
Input source
PC , HDMI , DVI (when a PC is connected)
Picture Mode
Information / Advertisement
Adjustable options
Backlight / Contrast / Brightness /
Sharpness
AV , Component , HDMI (720p, 1080i,
1080p)
Dynamic / Standard / Natural / Movie Backlight / Contrast / Brightness /
Sharpness / Color / Tint (G/R)
― When you make changes to Backlight , Contrast , Brightness , Sharpness , Color or Tint (G/R) , the OSD will be adjusted accordingly.
― You can adjust and store settings for each external device you have connected to an input on the product.
― Lowering picture brightness reduces power consumption.
The displayed image may differ depending on the model.
47
Picture Size
MENU m : T Picture Size ENTER
Picture Size
Picture Size
· Position
Resolution Select
16:9
Off
The displayed image may differ depending on the model.
Picture Size
If you have a cable box or satellite receiver, it may have its own set of screen sizes as well. However, we highly recommend you use your product’s 16:9 mode most of the time.
• 16:9 : Sets the picture to 16:9 wide mode.
• Zoom1 : Use for moderate magnification. Cuts off the top and sides.
• Zoom2 : Use for a stronger magnification.
• Smart View 1 : Reduces the 16:9 picture by 50%.
― Smart View 1 is enabled only in HDMI mode.
• Smart View 2 : Reduces the 16:9 picture by 25%.
― Smart View 2 is enabled only in HDMI mode.
• Wide Fit : Enlarges the aspect ratio of the picture to fit the entire screen.
• 4:3 : Sets the picture to basic ( 4:3 ) mode.
― Do not set your product to 4:3 format for a long time.
The borders displayed on the left and right, or top and bottom of the screen may cause image retention (screen burn) which is not covered by the warranty.
• Screen Fit : Displays the full image without any cut-off when HDMI (720p / 1080i / 1080p) signals are inputted.
• Custom : Changes the resolution to suit the user's preferences.
• Original Ratio : If the input source is PC , DVI , HDMI (PC connection) the video will display in the original aspect ratio.
― Available ports may differ depending on the model.
― You can adjust and store settings for each external device you have connected to an input on the product.
48
Picture Sizes available by Input Source.
Input Source
AV , Component (480i, 480p)
Component (1080i, 1080p)
HDMI (720p, 1080i, 1080p)
HDMI (480i, 480p)
PC , DVI , HDMI (when a PC is connected)
Picture Size
16:9 / 4:3 / Zoom1 / Zoom2 / Custom
16:9 / 4:3 / Wide Fit / Screen Fit / Custom
16:9 / 4:3 / Smart View 1 / Smart View 2 / Custom / Wide Fit /
Screen Fit
16:9 / 4:3 /
Custom
Zoom1 / Zoom2 / Smart View 1 / Smart View 2 /
16:9 / 4:3 / Original Ratio
49
Position
Picture Size
Picture Size
· Position
Resolution Select
16:9
Off
The displayed image may differ depending on the model.
Zoom/Position
Picture Size
Picture Size
· Zoom/Position
Resolution Select
Custom
Off
The displayed image may differ depending on the model.
Adjusts the picture position. Position is only available if Picture Size is set to Zoom1 , Zoom2 , Wide Fit , Screen Fit .
― To use the Position function after selecting Zoom1 , Zoom2 , Wide Fit , Screen Fit or Original Ratio , follow these steps.
1
Press the button to select Position . Press the button.
2
Press the or button to move the picture up or down.
3
Press the button.
― To use the Zoom/Position function after selecting Custom in HDMI (1080i/1080p) or Component (1080i/1080p) or
Custom , follow these steps.
1
Press the button to select Zoom/Position . Press the button.
2
Select the Zoom or Position . Press the button.
3 Press the / / / button to move the picture up or down.
4
Press the button.
― If you want to reset the picture to its original position, select Reset in the Zoom/Position screen.
The picture will be set to its default position.
50
Resolution Select
Picture Size
Picture Size
· Position
Resolution Select
Available in PC mode only.
The displayed image may differ depending on the model.
Auto Adjustment
MENU m : T Auto Adjustment ENTER
Picture
Auto Adjustment
Available in PC mode only.
The displayed image may differ depending on the model.
16:9
Off
If the picture is not normal even when the resolution of the graphics card is one of the following, you can optimize the picture quality by selecting the same resolution for the product as the PC using this menu.
Available resolutions: Off / 1024x768 / 1280x768 / 1360x768 / 1366x768
Adjust frequency values/positions and fine tune the settings automatically.
51
PC Screen Adjustment
PC Screen Adjustment
Coarse
Fine
Position
Image Reset
50
0
The displayed image may differ depending on the model.
• Coarse / Fine
Removes or reduces picture noise.
If the noise is not removed by Fine-tuning alone, use the Coarse function to adjust the frequency as best as possible
( Coarse ) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned with the center of screen.
• Position
To adjust the PC’s screen position if it is not centered or does not fit the product screen.
Press the or button to adjust the Vertical Position. Press the or button to adjust the Horizontal Position.
• Image Reset
Resets the image to the default settings.
52
PIP
MENU m : T PIP ENTER
Picture
PIP
The displayed image may differ depending on the model.
For PIP sound, refer to the Sound Select instructions.
If you turn the product off while watching in the PIP mode, the PIP function is reset to off.
When you turn your product on, you must turn PIP on again to watch in the PIP mode.
You may notice that the picture in the PIP screen becomes slightly unnatural when you use the main screen to view a game or karaoke.
PIP Settings
The picture from the external video source will be in the main screen and the picture from the product will be in the PIP subpicture screen.
Main picture
AV
Sub picture
PC , DVI , HDMI
Component
PC
DVI , HDMI
DVI , HDMI
AV , DVI , HDMI
AV , PC , Component
• PIP ( Off / On ): Activate or deactivate the PIP function.
• Source : You can select a source of the sub picture.
• Size ( , , , , , ): Select a size for the subpicture.
• Position ( , , , ): Select a position for the sub-picture.
― In ( , , ) mode, you cannot select Position .
• Sound Select ( Main / Sub ): You can choose to listen to the sound from the Main picture or the Sub picture.
53
Advanced Settings
MENU m : T Advanced Settings ENTER
Advanced Settings
Dynamic Contrast
Black Tone
Flesh Tone
RGB Only Mode
Color Space
Medium
Off
0
Off
Native
The displayed image may differ depending on the model.
Input Source
PC , DVI , HDMI (when a PC is connected)
Picture Mode
Information
Advertisement
AV , Component , HDMI
AV , Component , HDMI
Natural / Dynamic
Standard
Movie
Advanced Settings
White Balance / Gamma
White Balance / Gamma
Not available
Dynamic Contrast / Black Tone / Flesh Tone / RGB Only
Mode / Color Space / White Balance / Gamma / Motion
Lighting
Dynamic Contrast / Black Tone / Flesh Tone / RGB Only
Mode / Color Space / White Balance / Gamma
Dynamic Contrast
Adjust the screen contrast.
• Off / Low / Medium / High
Black Tone
Select the black level to adjust the screen depth.
• Off / Dark / Darker / Darkest
Flesh Tone
Emphasize pink Flesh Tone .
RGB Only Mode
Displays the Red , Green and Blue color for making fine adjustments to the hue and saturation.
• Off / Red / Green / Blue
54
Advanced Settings
Color Space
White Balance
Gamma
Motion Lighting
Native
0
Off
The displayed image may differ depending on the model.
Color Space
Adjusts the range and variety of colors (the color space) available to create images.
• Auto / Native
White Balance
Adjust the color temperature for a more natural picture.
• R-Offset / G-Offset / B-Offset : Adjust each color’s (red, green, blue) darkness.
• R-Gain / G-Gain / B-Gain : Adjust each color’s (red, green, blue) brightness.
• Reset : Resets the White Balance to its default settings.
Gamma
Adjust the primary color intensity.
Motion Lighting
Reduces power consumption by reducing screen brightness when the picture on the screen is in motion.
• Off / On
55
Picture Options
MENU m : T Picture Options ENTER
Picture Options
Color Tone
Color Temp.
Digital Clean View
MPEG Noise Filter
HDMI Black Level
Film Mode
Dynamic Backlight
Standard
10000K
Off
Off
Normal
Off
Off
The displayed image may differ depending on the model.
Select an option using the and arrow keys, and the press .
Use the arrow keys to change the setting, and then press .
Input source Picture Mode Picture Options
PC Information Color Tone / Color Temp.
/ Dynamic Backlight
DVI , HDMI (when a PC is connected)
AV , Component , HDMI
Advertisement
Information
Advertisement
Dynamic / Standard /
Natural / Movie
Color Tone / Color Temp.
/ Dynamic Backlight
Color Tone / Color Temp.
/ HDMI Black Level / Dynamic
Backlight
Color Tone / Color Temp.
/ HDMI Black Level / Dynamic
Backlight
Color Tone / Color Temp.
/ Digital Clean View / MPEG
Noise Filter / Film Mode / Dynamic Backlight
56
Picture Options
Color Tone
Color Temp.
Digital Clean View
MPEG Noise Filter
HDMI Black Level
Film Mode
Dynamic Backlight
Standard
10000K
Off
Off
Normal
Off
Off
The displayed image may differ depending on the model.
Color Tone
If the input source is PC , DVI , HDMI (PC connection).
• Off / Cool / Standard / Warm
If the input source is AV , Component , HDMI .
• Off / Cool / Standard / Warm1 / Warm2
― Warm1 or Warm2 will be deactivated when the Picture Mode is Dynamic .
― Settings can be adjusted and stored for each external device connected to an input on the product.
Color Temp.
Adjust the color temperature ( Red / Green / Blue ). (Range: 3000K–15000K)
― This option is available when
Color Tone is set to Off .
Digital Clean View
If the broadcast signal received by your product is weak, you can activate the Digital Clean View feature to reduce any static and ghosting that may appear on the screen.
• Off / Low / Medium / High / Auto
― When the signal is weak, try all the options until the the product displays the best picture.
MPEG Noise Filter
Reduces MPEG noise to provide improved picture quality.
• Off / Low / Medium / High / Auto
57
Picture Options
HDMI Black Level
Film Mode
Dynamic Backlight
Normal
Off
Off
The displayed image may differ depending on the model.
HDMI Black Level
Selects the black level on the screen to adjust the screen depth.
• Normal / Low
― Available only in HDMI mode (AV Timing : 480p, 576p, 720p, 1080i, 1080p).
Film Mode
This mode is suitable to view movies.
Sets the product to automatically sense and process film signals from all sources and adjust the picture for optimum quality.
• Off / Auto1 / Auto2
― Available in HDMI (1080i).
Dynamic Backlight
Automatically adjust the backlight to provide the best possible screen contrast under the current conditions.
• Off / On
― The Dynamic Backlight is not available when the input source is set to PC while Video Wall is On .
58
Picture Off
Picture
Picture Off
Reset Picture
The displayed image may differ depending on the model.
Reset Picture
Picture
Picture Off
Reset Picture
The displayed image may differ depending on the model.
The product screen is turned off but the audio will continue. Press any key on your remote to turn the screen back on.
Resets your current picture mode to its default settings.
59
Chapter 06
Sound Adjustment
Configure the sound ( Sound ) settings for the product.
Sound Mode
MENU m : T Sound Mode ENTER
Sound
Sound Mode
Sound Effect
Speaker Settings
Reset Sound
Standard
The displayed image may differ depending on the model.
You can select a sound mode to suit your personal preferences.
• Standard : Selects the normal sound mode.
• Music : Emphasizes music over voices.
• Movie : Provides the best sound for movies.
• Clear Voice : Emphasizes voices over other sounds.
• Amplify : Increase the intensity of high-frequency sound to allow a better listening experience for the hearing impaired.
― If Speaker Select is set to External , Sound Mode is disabled.
60
Sound Effect
MENU m : T Sound Effect ENTER
Sound
Sound Mode
Sound Effect
Speaker Settings
Reset Sound
Standard
The displayed image may differ depending on the model.
Configure your preferred sound effect for output sound.
― If Speaker Select is set to External , Sound Effect is disabled.
― Available only when Sound Mode is set to Standard .
• DTS TruSurround ( Off / On )
This function provides a virtual 5.1 channel surround sound experience through a pair of speakers using HRTF(Head
Related Transfer Function) technology.
• DTS TruDialog ( Off / On )
This function allows you to increase the intensity of a voice over background music or sound effects so that dialog can be heard more clearly.
• Equalizer
Use Equalizer to customize sound setting for each speaker.
Balance(L/R) : Adjusts the balance between the right and left speaker.
100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment): Adjusts the level of specific bandwidth frequencies.
Reset : Resets the equalizer to its default settings.
61
Speaker Settings
MENU m : T Speaker Settings ENTER
Sound
Standard Sound Mode
Sound Effect
Speaker Settings
Reset Sound
The displayed image may differ depending on the model.
Reset Sound
MENU m : T Reset Sound ENTER
Sound
Standard Sound Mode
Sound Effect
Speaker Settings
Reset Sound
The displayed image may differ depending on the model.
• Speaker Select ( External / Internal / Receiver )
If you are listening to the sound track of a broadcast or movie through an external receiver, you may hear a sound echo caused by the difference in decoding speed between the products speakers and the speakers attached to your audio receiver. If this occurs, set the product to External .
― When you set Speaker Select to External , the products speakers are turned off.
You will hear sound through the external speakers only. When the Speaker Select is set to Internal , both the product speakers and the external speakers are on. You will hear sound through both.
― If there is no video signal, both the products speakers and the external speakers will be mute.
Reset all sound settings to the factory defaults.
62
Chapter 07
Applications
Source List
Source allows you to select a variety of sources and change source device names.
You can display the screen of a source device connected to the product. Select a source from Source List to display the screen of the selected source.
― The input source can also be changed by using the SOURCE button on the remote control.
― The screen may not display correctly if an incorrect source is selected for the source device you want to convert to.
MENU m : T Source List ENTER
Applications
Source List
Refresh
MENU m : T Source List TOOLS Refresh ENTER
If you cannot find a device you want, select Refresh to refresh the list.
Edit Name
MENU m : T Source List TOOLS Edit Name ENTER
Sometimes the screen will not display properly unless the name of a source device is specified in Edit Name .
In addition, it is best to rename the source device in Edit Name to obtain optimal picture quality.
― The list can include the following source devices. Source devices on the list differ depending on the selected source.
VCR / DVD / Cable STB / Satellite STB / PVR STB / AV Receiver / Game / Camcorder / PC / DVI PC / DVI Devices / TV /
IPTV / Blu-ray / HD DVD / DMA
― Available settings in the Picture menu depend on the current source and settings made in Edit Name .
• When connecting a PC to the HDMI IN port with HDMI cable, you should set the product to PC mode under Edit Name .
• When connecting a PC to the HDMI IN port with HDMI to DVI cable, you should set the product to DVI PC mode under
Edit Name .
• When connecting an AV devices to the HDMI IN port with HDMI to DVI cable, you should set the product to DVI Devices mode under Edit Name .
Information
MENU m : T Source List TOOLS Information ENTER
You can see detailed information about the selected external device.
The displayed image may differ depending on the model.
63
Chapter 08
System
Menu Language
MENU m : T Menu Language ENTER
System
Menu Language
Multi Control
Time
Eco Solution
Screen Burn Protection
Ticker
English
Off
The displayed image may differ depending on the model.
Set the menu language.
― A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions on your PC.
64
Multi Control
MENU m : T Multi Control ENTER
System
Menu Language
Multi Control
Time
Eco Solution
Screen Burn Protection
Ticker
English
Off
The displayed image may differ depending on the model.
Configuring settings for Multi Control
• ID Setup
Assign an ID to a set. (Range: 0~99)
Press or to select a number, and press .
• ID Input
Enter the ID number of the product connected to the input cable for input signal reception.
Enter the number you want using the number buttons on the remote control.
65
Time
MENU m : T Time ENTER
Time
Clock Set
Sleep Timer
The displayed image may differ depending on the model.
You can configure Clock Set or Sleep Timer . You can also set the product to automatically turn on or off at a specified time using the Timer function.
Clock Set
Set the clock to use the various various timer features of the product.
• Clock Set
Set the Date and Time .
Select Clock Set . Select Date or Time , and then press .
Use the number buttons to enter numbers or press the up and down arrow buttons. Use the left and right arrow buttons to move from one entry field to the next. Press when done.
― You can set the Date and Time directly by pressing the number buttons on the remote control.
Sleep Timer
Automatically shuts off the product after a preset period of time.
( Off / 30 min.
/ 60 min.
/ 90 min.
/ 120 min.
/ 150 min.
/ 180 min.
)
― Use the up and down arrows to select a period of time, and then press . To cancel Sleep Timer , select Off .
66
Time
On Timer
Off Timer
Holiday Management
The displayed image may differ depending on the model.
On Timer
Set On Timer so that your product turns on automatically at a time and on a day of your choosing.
The power is turned on with the specified volume or input source.
On Timer : Set the on timer by making a selection from one of the seven options. Ensure you set the current time first.
( On Timer1 ~ On Timer7 )
― You must set the clock before you can use On Timer .
• Setup : Select Off , Once , Everyday , Mon~Fri , Mon~Sat , Sat~Sun or Manual . If you select Manual , you can choose the days you want On Timer to turn on your product.
― The check mark indicates days you’ve selected.
• Time : Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use the left and right arrow buttons to change entry fields.
• Volume : Set the desired volume level. Use the left and right arrow buttons to change the volume level.
• Source : Select the input source of your choice.
67
Time
On Timer
Off Timer
Holiday Management
The displayed image may differ depending on the model.
Off Timer
Set the off timer ( Off Timer ) by making a selection from one of the seven options. ( Off Timer1 ~ Off Timer7 )
― You must set the clock before you can use Off Timer .
• Setup : Select Off , Once , Everyday , Mon~Fri , Mon~Sat , Sat~Sun or Manual . If you select Manual , you can choose the days you want Off Timer to turn off your product.
― The check mark indicates days you’ve selected.
• Time : Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use the left and right arrow buttons to change entry fields.
Holiday Management
Timer will be disabled during a period specified as a holiday.
• Add : Specify the period you want to add as a holiday.
Select the start and end dates of the holiday you want to add using the / buttons, and click the Save button.
The period will be added to the list of holidays.
Start : Set the start date of the holiday.
End : Set the end date of the holiday.
Delete : Delete all items from the list of holidays.
Select Delete . The message " Delete all holidays?
" will appear.
Select Yes . All holidays will be deleted.
• Apply : Set the On Timer and Off Timer to not activate on public holidays.
Press to select the On Timer and Off Timer settings you do not want to activate.
The selected On Timer and Off Timer will not activate.
68
Eco Solution
MENU m : T Eco Solution ENTER
Eco Solution
Energy Saving
Eco Sensor
Auto Power Off
Off
Off
Off
The displayed image may differ depending on the model.
Energy Saving
Reduce the power consumption by adjusting the screen brightness.
• Off / Low / Medium / High
Eco Sensor
To enhance your power savings, the picture settings will automatically adapt to the light in the room.
•
Off / On
― Adjusting the Backlight setting under Picture while Eco Sensor is on will disable the Off .
•
Min. Backlight : When Eco Sensor is On , you can manually adjust the minimum screen brightness.
― If Eco Sensor is On , the display brightness may change (become slightly darker or brighter) depending on the surrounding light intensity. You can control the screen’s minimum brightness with the Min. Backlight function.
Auto Power Off
The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel within 4 hours to prevent overheating.
•
Off / On
69
Screen Burn Protection
MENU m : T Screen Burn Protection ENTER
Screen Burn Protection
Pixel Shift
Timer
Immediate Display
Side Gray
Off
Off
Off
Off
The displayed image may differ depending on the model.
To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology.
Pixel Shift moves the picture slightly on the screen.
The Pixel Shift Time setting allows you to program the time between movements of the picture in minutes.
Pixel Shift
Minimize image retention by finely moving pixels horizontally or vertically.
• Horizontal : Sets how many pixels the screen moves horizontally.
• Vertcal : Sets how many pixels the screen moves vertically.
• Time : Set the time interval for performing the horizontal or vertical movement, respectively.
Available Pixel Shift Settings and Optimum Settings.
Available Settings Optimum Settings
Horizontal (pixels) 0 ~ 4 4
Vertcal (pixels) 0 ~ 4 4
Time (minute) 1 min.
~ 4 min.
4 min.
― The Pixel Shift value may differ depending on the product size (inches) and mode.
― Displaying a still image or a 4:3 output for an extended period of time may cause image retention. This is not a defect in the product.
― This function is not available in the Screen Fit mode.
70
Screen Burn Protection
Pixel Shift
Timer
Immediate Display
Side Gray
The displayed image may differ depending on the model.
Off
Off
Off
Off
Timer
You can set the timer for Screen Burn Protection .
The Pixel Shift feature stops automatically after a specified period of time.
• Off
• Repeat : Display the image retention-preventive pattern set in Mode at specified time intervals( Period ).
―
Period and Time can be configured when Repeat is selected.
• Interval : Display the image retention-preventive pattern set in Mode for a specified period of time (from Start Time to
End Time ).
― The option is enabled only when Clock Set is configured.
• Mode : Select a screen protective pattern to display.
Pixel : Pixels on the screen alternate black continuously.
Rolling Bar : A vertical bar moves left to right.
Fading Screen : The entire screen becomes brighter, then darker.
― The Rolling Bar and Fading Screen patterns appear only once regardless of the specified repeat period or time.
• Period : Specify the time interval to activate the Screen Burn Protection function.
Hour 1 ~ Hour 10
― The option is enabled when Repeat is selected for Timer .
• Time : Specify the duration to keep the Screen Burn Protection function on.
10 sec ~ 50 sec
― The option is enabled when Pixel is selected for Mode .
• Start Time : Set the start time to activate the screen protection function.
― The option is enabled when Interval is selected for Timer .
• End Time : Set the end time to deactivate the screen protection function.
― The option is enabled when Interval is selected for Timer .
71
Screen Burn Protection
Pixel Shift
Timer
Immediate Display
Side Gray
The displayed image may differ depending on the model.
Off
Off
Off
Off
Immediate Display
Select the screen saver you want to display immediately.
• Off / Pixel / Rolling Bar / Fading Screen
Side Gray
When the screen is set to 4:3 aspect ratio, adjust the brightness of white margins on sides to protect the screen.
• Off / Light / Dark
72
Ticker
MENU m : T Ticker ENTER
System
Screen Burn Protection
Ticker
Video Wall
Source AutoSwitch Settings
The displayed image may differ depending on the model.
The Ticker function is only available when Menu Language is set to English .
Input text while a video or image is displayed and display the text on the screen.
• Off / On
― Message , Time , Position , Motion , and Font Style are enabled only when Ticker is set to On .
• Message : Enter a message to display on the screen.
• Time : Set the Start Time and End Time to display a Message .
•
•
Position : Select an orientation to display a Message from Horizontal and Vertical .
Horizontal ( Left / Center / Right )
Vertical ( Up / Middle / Down )
• Motion : Specify the Direction and Speed to display a Message .
Motion ( Off / On )
Direction ( Left / Right / Up / Down )
Speed ( Slow / Normal / Fast )
― Direction and Speed are enabled only when Motion is set to On .
Font Style : Specify the message Size and Font Color .
73
Video Wall
MENU m : T Video Wall ENTER
Video Wall
Video Wall
· Format
· Horizontal
· Vertical
· Screen Position
On
Full
1
1
The displayed image may differ depending on the model.
Some models may not support the MagicInfo function.
The Video Wall option is only enabled when PIP is set to Off .
If more than four displays are connected horizontally and vertically, it is recommended that you use an input resolution of XGA (1024 x 768) level or higher to prevent a dark picture due to degradation in the contrast or color intensity.
Customize the layout of multiple displays that are connected to form a video wall.
In addition, display part of a whole picture or repeat the same picture on each of the connected multiple displays.
Video Wall
You can activate or deactivate Video Wall .
To organize a video wall, select On .
Format
Select a format to display images on multiple displays.
• Full : Display images in full screen.
• Natural : Display images at the original resolution without enlarging or reducing.
― The Format option is only enabled when Video Wall is set to On .
Horizontal
This function automatically divides the screen according to the specified number of horizontal displays.
Enter the number of horizontally arranged displays.
The horizontal screen will automatically be divided according to the number entered.
A maximum of 15 displays can be assigned to the horizontal arrangement.
― The screen can be divided into a maximum of 100 screens (horizontal and vertical screens multiplied). For example, if the horizontal arrangement is set to 15, a maximum of 6 displays can be assigned to the vertical arrangement. Conversely, if the vertical arrangement is set to 15, a maximum of 6 displays can be assigned to the horizontal arrangement.
― The Horizontal option is only enabled when Video Wall is set to On .
74
Video Wall
Video Wall
· Format
· Horizontal
· Vertical
· Screen Position
The displayed image may differ depending on the model.
On
Full
1
1
Vertical
This function automatically divides the screen according to the specified number of vertical displays.
Enter the number of vertically arranged displays.
The vertical screen will automatically be divided according to the number entered.
A maximum of 15 displays can be assigned to the vertical arrangement.
― The screen can be divided into a maximum of 100 screens (horizontal and vertical screens multiplied). For example, if the horizontal arrangement is set to 15, a maximum of 6 displays can be assigned to the vertical arrangement. Conversely, if the vertical arrangement is set to 15, a maximum of 6 displays can be assigned to the horizontal arrangement.
― The Vertical option is only enabled when Video Wall is set to On .
Screen Position
You can customize the arrangement of split screens by moving displays identified with a number using the Screen Position function.
Select Screen Position to display the arrangement of displays (identified with a number) specified according to the
Horizontal or Vertical settings. To customize the arrangement, move a number (display) using the direction buttons on the remote control and press .
― A maximum of 100 displays can be arranged in Screen Position .
― The Screen Position option is only enabled when Video Wall is set to On .
― The Screen Position window is only displayed when Horizontal and Vertical are configured.
75
Source AutoSwitch Settings
MENU m : T Source AutoSwitch Settings ENTER
Source AutoSwitch Settings
Source AutoSwitch
· Primary Source Recovery
· Primary Source
· Secondary Source
On
Off
All
PC
The displayed image may differ depending on the model.
Turning on the display with Source AutoSwitch On , and the previous video source selection is not active, the display will automatically search the different video input sources for active video.
Source AutoSwitch
When the Source AutoSwitch is On , the display video source will automatically be searched for active video.
The Primary Source selection will be activated, if the current video source is not recognized.
Secondary Source selection will become active, if no primary video source is available.
If both the primary and secondary input sources are not recognized, the display will perform two searches for an active source, each search checking the primary and then secondary source. If both searches fail, the display will return to the first video source and display a message indicating that there is no signal.
When the Primary Source selection is set to All , the display will search all the video source inputs twice in sequence looking for an active video source, returning back to the first video source in the sequence if no video is found.
Primary Source Recovery
Select whether to restore the selected primary input source when a primary input source is connected.
― The Primary Source Recovery function is disabled if Primary Source is set to All .
Primary Source
Specify Primary Source for the automatic input source.
Secondary Source
Specify Secondary Source for the automatic input source.
76
Change PIN
MENU m : T Change PIN ENTER
System
Change PIN
The displayed image may differ depending on the model.
The Change PIN screen will appear.
Choose any 4 digits for your PIN and enter it in Enter New PIN . Reenter the same 4 digits in Confirm New PIN .
When the Confirm screen disappears, press the Close button. The product has memorized your new PIN.
77
General
MENU m : T General ENTER
General
Max. Power Saving
Game Mode
Auto Power
Safety Lock
Button Lock
Standby Control
Lamp Schedule
On
Off
Off
Off
Off
Off
Off
The displayed image may differ depending on the model.
Max. Power Saving
Turns off the product to reduce power consumption after the PC has been left idle for a specified period of time.
• Off / On
― Available only PC , DVI , HDMI mode.
Game Mode
When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by selecting game mode.
• Off / On
― Precautions and limitations for Game Mode
To disconnect the game console and connect another external device, set Game Mode to Off in the setup menu.
― Game Mode is not available when the input source is set to PC .
― If Game Mode is On . Picture Mode is set to Standard and Sound Mode is set to Movie .
Auto Power
Enabling this option will automatically power on the product if the power cable is connected.
• Off / On
Safety Lock
It sets safe lock function.
• Off / On
All the menus and buttons of the product and remote control, except for the LOCK button on the remote control, will be locked by the Safety Lock function.
To unlock the menus and buttons, press the LOCK button and then enter the password (default password: 0 - 0 - 0 - 0).
78
General
Max. Power Saving
Game Mode
Auto Power
Safety Lock
Button Lock
Standby Control
Lamp Schedule
The displayed image may differ depending on the model.
Off
Off
Off
On
Off
Off
Off
Button Lock
This menu can be used to lock the buttons on the product.
Only the remote control can control the product if Button Lock is set to On .
• Off / On
Standby Control
You can set the screen standby mode to be applied when an input signal is received.
• Auto
Power-saving mode will activate if no input signals are detected even though a source device is connected to the display.
The message No Signal will appear if no source device is connected.
• On
Power-saving mode will activate if no input signals are detected.
• Off
The message No Signal will appear if no input signals are detected.
― The Standby Control option is only enabled when Source List is set to PC , DVI , HDMI .
― If No Signal is displayed although a source device is connected, check the cable connection.
Lamp Schedule
Enables the lamp value to be adjusted to a user-specified value at a specified time in MDC mode.
• Off / On
79
General
OSD Display
Power On Adjustment
Temperature Control
The displayed image may differ depending on the model.
0 sec
77
OSD Display
Displays or hides a menu item on the screen.
― Source OSD / No Signal OSD / MDC OSD
Power On Adjustment
You can set the warm-up time for the screen to turn on after the power button is pressed. (Range: 0 – 50 seconds)
― A warm-up time that is too short may damage the product due to overvoltage.
Temperature Control
This function detects the internal temperature of the product. You can specify the temperature range that is acceptable.
The default temperature is set to 77 C.
The recommended operating temperature for this product is 75 to 80 C (based on an ambient temperature of 40 C).
― The screen will become darker if the current temperature exceeds the specified temperature limit. If the temperature continues to rise, the product will power off to prevent overheating.
80
Anynet+ (HDMI-CEC)
MENU m : T Anynet+ (HDMI-CEC) ENTER
Anynet+ (HDMI-CEC)
Anynet+ (HDMI-CEC)
Auto Turn Off
On
Yes
The displayed image may differ depending on the model.
The Anynet+ (HDMI-CEC) functions do not operate with other manufacturers’ products.
For instructions explaining how to connect Anynet+ external devices, refer to the device’s user manual.
You can connect only one receiver (home theater).
Anynet+ (HDMI-CEC)
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung product remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your
Samsung device has this feature, check if there is an Anynet+ logo on it.
― You can only control Anynet+ devices using the product remote control, not the buttons on the product.
― The product remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.
― Anynet+ works when the AV device supporting Anynet+ is in the standby or on status.
― While in PIP mode, Anynet+ functions only when an AV device is connected as the primary display. It does not work if the
AV device is connected as a secondary display.
― Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the product.
Anynet+ Menu
View PC
Description
Changes Anynet+ mode to PC mode.
Device List
(device_name) MENU
(device_name) Tools
Shows the Anynet+ device list.
Shows the menu of the connected device menus. E.g. if a DVD player is connected, the disc menu of the DVD player will appear.
Shows the tools menu of the connected device. E.g. if a DVD player is connected, the tools menu of the DVD player will appear.
― Depending on the device, this menu may not be available.
(device_name) Title Menu Shows the title menu of the disc in the connected device. E.g. If a DVD player is connected, the title menu of the movie in the DVD player will appear.
― Depending on the device, this menu may not be available.
81
Anynet+ (HDMI-CEC)
Anynet+ (HDMI-CEC)
Auto Turn Off
The displayed image may differ depending on the model.
On
Yes
Auto Turn Off
Setting an Anynet+ Device to turn Off automatically when the product is turned off.
• No / Yes
― If Auto Turn Off is set to Yes , running external devices will turn off at the same time as the product powers off.
― May not be enabled depending on the device.
Switching between Anynet+ Devices
1 Press the TOOLS button, select Anynet+ (HDMI-CEC) , and then press .
2 Select Device List , and then press the button.
If you cannot find a device you want, select Refresh to refresh the list.
3
Select a device, and then press the button. You can switch to the selected device.
― The Device List menu appears only when you set Anynet+ (HDMI-CEC) to On in the System menu.
― Switching to the selected device may take up to 2 minutes. You cannot cancel the switching operation while switching is in progress.
― If you have selected an Anynet+ device by pressing the SOURCE button and then selecting its input source, you cannot use the Anynet+ function.
― Make sure to switch to an Anynet+ device by using the Device List .
82
Troubleshooting for Anynet+
Problem
Anynet+ does not work.
I want to start Anynet+.
I want to exit Anynet+.
The message “ Connecting to
Anynet+ device ...
” appears on the screen.
The Anynet+ device does not play.
Possible Solution
• Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
• You can connect only one receiver (home theater).
• Check if the Anynet+ device power cord is properly connected.
• Check the Anynet+ device’s Video/Audio/HDMI cable connections.
• Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+setup menu.
• Check whether the remote control is Anynet+ compatible.
• Anynet+ doesn’t work in certain situations. (initial setup)
• If you have removed and then reconnected the HDMI cable, please make sure to search devices again or turn your product off and on again.
• Check if the Anynet+ function of the Anynet device is set on.
• Check if the Anynet+ device is properly connected to the product and check if the Anynet+ (HDMI-CEC) is set to On in the
Anynet+ System menu.
• Press the TOOLS button to display the Anynet+ menu and select a menu you want.
• Select View PC in the Anynet+ menu.
• Press the SOURCE button on the product remote control and select a non- Anynet+ device.
• You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
• Use the remote control after the product has completed Anynet+ configuration or has finished switching to Anynet+.
• You cannot use the play function when initial setup is in progress.
83
Problem
The connected device is not displayed.
Possible Solution
• Check whether or not the device supports Anynet+ functions.
• Check whether or not the HDMI cable is properly connected.
• Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ System menu.
• Search Anynet+ devices again.
• Anynet+ requires an HDMI connection. Make sure the device is connected to your product with an HDMI cable.
• Some HDMI cables may not support Anynet+ functions.
• If the connection is terminated because there has been a power failure or the HDMI cable has been disconnected, please repeat the device scan.
84
Magic Clone
MENU m : T Magic Clone ENTER
Magic Clone
Clone to USB
Clone From USB
The displayed image may differ depending on the model.
Reset System
MENU m : T Reset System ENTER
System
Reset System
The displayed image may differ depending on the model.
Export the product settings to a USB device or load the settings via a USB device.
This option is useful when assigning the same settings to several products.
• Clone to USB : Copy the product settings to a USB device.
• Clone From USB : Assign the settings saved in a USB device to the product.
After configuration is complete, the product is rebooted automatically.
― The option may not work properly if the USB device contains a file other than a settings file.
― Confirm that the USB device functions properly before running the option.
― The option is available for products with the same Model Code and Software Version .
Go to Support Contact Samsung and find the product Model Code and Software Version .
This option returns the current settings under system to the default factory settings.
85
Reset All
MENU m : T Reset All ENTER
System
Reset All
The displayed image may differ depending on the model.
This option returns all the current settings for a display to the default factory settings.
86
Chapter 09
Support
Software Update
MENU m : T Software Update ENTER
The Software Update menu lets you upgrade your product software to the latest version.
― Be careful not to turn off the power until the upgrade is complete. The product will turn off and on automatically after completing the software upgrade.
― When you upgrade software, all video and audio settings you have made will return to their default settings. We advise you to write down your settings so that you can easily reset them after the upgrade.
By USB
To perform a software update from a USB device, contact the customer service center.
Contact Samsung
MENU m : T Contact Samsung ENTER
View this information when your product does not work properly or when you want to upgrade the software.
You can find information regarding our call centers and how to download products and software.
― Contact Samsung and find the product Model Code and Software Version .
87
Chapter 10
Troubleshooting Guide
Before calling Samsung Customer Service
Center, test your product as follows. If the problem persists, contact Samsung
Customer Service Center.
If the screen remains blank, check the PC system, video controller and cable.
Requirements Before Contacting Samsung Customer Service Center
Testing the Product
Check if your product is operating normally by using the product test function.
If the screen remains blank while the power LED blinks even when the product is correctly connected to a PC, perform product testing.
1
Power off both the PC and product.
2
Disconnect all the cables from the product.
3
Power on the product.
4
If No Signal is displayed, the product is operating normally.
Checking the Resolution and Frequency
Not Optimum Mode will briefly be displayed if a mode that exceeds a supported resolution is selected
(refer to Supported Resolutions).
88
Check the followings.
Installation issue (PC mode)
The screen keeps switching on and off.
Check the cable connection between the product and PC, and ensure the connection is secure.
Blank spaces are found on all four sides of the screen when an HDMI or HDMI-DVI cable is connected to the product and
PC.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the screen size in the HDMI or DVI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update the graphics card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to adjust the screen settings.)
PC is shown in Source when a PC is not connected.
PC is always shown in Source irrespective of whether or not a PC is connected.
Screen issue
The power LED is off. The screen will not switch on.
No Signal is displayed on the screen (refer to "Connecting to a PC").
Make sure that the power cord is connected.
Check that the product is connected correctly with a cable
Check that the device connected to the product is powered on.
Not Optimum Mode is displayed.
This message is displayed when a signal from the graphics card exceeds the product's maximum resolution and frequency.
Refer to the Standard Signal Mode Table and set the maximum resolution and frequency according to the product specifications.
The images on the screen look distorted.
Check the cable connection to the product
89
Screen issue
The screen is not clear. The screen is blurry.
The screen appears unstable and shaky.
There are shadows or ghost images left on the screen.
The screen is too bright. The screen is too dark.
Screen color is inconsistent.
White does not really look white.
There is no image on the screen and the power LED blinks every 0.5 to 1 second.
The product will turn off automatically.
Picture quality of the product is different from the dealer shop where it was purchased.
Adjust Coarse and Fine .
Remove any accessories (video extension cable, etc) and try again.
Set the resolution and frequency to the recommended level.
Check that the resolution and frequency of the PC and graphics card are set within a range compatible with the product. Then, change the screen settings if required by referring to the Additional
Information on the product menu and the Standard Signal Mode Table.
Adjust Brightness and Contrast .
Go to Picture and adjust the Color Space settings.
Go to Picture and adjust the White Balance settings.
The product is in power-saving mode.
Press any key on the keyboard or move the mouse to return to the previous screen.
Go to System and make sure Sleep Timer is set to Off .
If a PC is connected to the product, check the power status of the PC.
Make sure the power cable is connected properly to the product and power outlet.
If the signal from a connected device is not detected, the product automatically turns off after 10 to 15 minutes.
Use an HDMI cable to obtain high-definition (HD) picture quality.
90
Screen issue
The screen display does not look normal.
The brightness and color do not look normal.
Broken lines are displayed on the edges of the screen.
Lines (red, green or blue) are displayed on the screen.
The display looks unstable and then freezes.
The screen cannot be displayed in full screen.
Encoded video content may cause the display to appear corrupted in scenes featuring fast moving objects such as in a sports event or action video.
Low signal level or low picture quality may cause the display to appear corrupted. This does not mean the product is defective.
A cell phone within a distance of one-meter radius may cause static on analog and digital products.
Go to Picture and adjust the screen settings such as Picture Mode , Color , Brightness and
Sharpness .
― Refer to
Picture menu.
Go to System and adjust the Energy Saving settings.
― Refer to
System menu.
Reset the screen settings to the default settings.
― Refer to
Reset Picture menu.
If Picture Size is set to Screen Fit , change the setting to 16:9 .
These lines are displayed when there is a defect in DATA SOURCE DRIVER IC on the monitor. Contact a
Samsung Service Center to resolve the issue.
The screen may freeze when a resolution other than the recommended resolution is used or if the signal is not stable. To resolve the issue, change the PC resolution to the recommended resolution.
A scaled SD (4:3) content file can cause black bars on both sides of an HD channel screen.
A video with an aspect ratio different from the product can cause black bars at the top and bottom of the screen.
Change the screen size setting to full screen on the product or source device.
91
Sound issue
There is no sound.
The volume is too low.
Video is available but there is no sound.
There is static coming from the speakers.
Check the connection of the audio cable or adjust the volume.
Check the volume.
Adjust the volume.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software program.
If an HDMI cable is connected, check the audio output settings on the PC.
Go to Sound and change Speaker Select to Internal .
If a source device is used
• Make sure the audio cable is properly connected to the audio input port on the product.
• Check the audio output settings for the source device.
(For example, if an HDMI cable is connected to the monitor, the audio setting for the cable box may need to be changed to HDMI.)
If a DVI-HDMI cable is used, a separate audio cable is required.
If the product has a headphone port, make sure nothing is connected to it.
Reconnect the power cable to the device and then reboot the device.
Check the cable connection. Make sure a video cable is not connected to an audio input port.
Check the signal strength after connecting a cable.
Low signal level can cause corrupted sound.
92
Sound issue
There is audible sound when the volume is muted.
When Speaker Select is set to External , the volume button and mute function are disabled.
Adjust the volume for the external speakers.
Audio settings for main speakers are separate from the internal speakers on the product.
Changing or muting the volume on the product does not affect an external amplifier(decoder).
Sound from the monitor does not change after Sound Mode is changed.
Audio settings for main speakers are separate from the internal speakers on the product.
Audio settings on a source device do not affect the internal speaker settings on the product.
There is an echo sound coming from the speakers.
Different decoding speeds between the product speakers and external speakers can cause an echo.
In this case, set Speaker Select to External .
Remote control issue
The remote control does not work.
Make sure that the batteries are correctly in place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs switched on in the vicinity.
Source device issue
A beeping sound is heard when my PC is booting.
If a beeping sound is heard when your PC is booting, have your PC serviced.
93
Other issue
Small particles are found on the edges of the product.
The PIP menu is not available.
When I try to change the PC resolution, a message " defined resolution is not currently supported.
The
" appears.
There is no sound from the speakers in HDMI mode when a
DVI-HDMI cable is connected.
HDMI Black Level is not functioning properly on an HDMI device with YCbCr output.
There is no sound in HDMI mode.
The particles are part of the product design. The product is not defective.
The menu is enabled or disabled depending on the Source mode.
― Refer to
for details about the PIP menu.
The message " The defined resolution is not currently supported.
" appears if the input source resolution exceeds the maximum resolution of the display.
To resolve the issue, change the PC resolution to a resolution supported on the display.
DVI cables do not transmit sound data.
Make sure to connect the audio cable to the correct input jack to enable audio.
This function is available only when a source device, such as a DVD player and STB, is connected to the product via an HDMI (RGB signal) cable.
Displayed picture colors may not look normal. Video or sound may not be available. This can occur if a source device that only supports an older version of the HDMI standard is connected to the product.
If these issues occur, connect an audio cable along with the HDMI cable.
Some PC graphics cards may not automatically recognize HDMI signals that do not include sound. In this case, manually select a sound input.
PC
DVI PC
Sound input
Auto
Audio In(Stereo ports )
Screen mode
PC settings
PC settings
94
Other issue
The IR sensor is not functioning.
Make sure the sensor light turns on when a button is pressed on the remote control.
• If the sensor light does not turn on, turn the power switch off and then on again on the back of the product.
(The power LED lights up red when the screen is switched off.)
If the sensor light still does not turn on after the power switch is turned off and then on again, an internal jack may be disconnected.
Contact your nearest service center to have the product serviced.
• If the sensor light that is on does not flash red when a button is pressed on the remote control, the IR sensor may be defective.
Contact your nearest service center to have the product serviced.
• If there is no change on the screen when a button is pressed on the remote control although the sensor light flashes red, the mainboard may be defective.
Contact your nearest service center to have the product serviced.
95
Refer to the user manual for your PC or graphics card for further instructions on adjustment.
Q & A
Question
How can I change the frequency?
How can I change the resolution?
Answer
Set the frequency on your graphics card.
• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings →
Advanced → Monitor and adjust the frequency in Monitor Settings.
• Windows ME/2000: Go to Control Panel → Display → Settings → Advanced → Monitor and adjust the frequency in Monitor Settings.
• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize →
Display Settings → Advanced Settings → Monitor and adjust the frequency in Monitor
Settings.
• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust resolution → Advanced Settings → Monitor and adjust the frequency in Monitor Settings.
• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display
→ Adjust resolution → Advanced Settings → Monitor and adjust the frequency in Monitor
Settings.
• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings and adjust the resolution.
• Windows ME/2000: Go to Control Panel → Display → Settings and adjust the resolution.
• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize →
Display Settings and adjust the resolution.
• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust
Resolution and adjust the resolution.
• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display
→ Adjust Resolution and adjust the resolution.
96
Question
How do I set powersaving mode?
Answer
• Windows XP: Set power-saving mode in Control Panel → Appearance and Themes → Display
→ Screen Saver Settings or BIOS SETUP on the PC.
• Windows ME/2000: Set power-saving mode in Control Panel → Display → Screen Saver
Settings or BIOS SETUP on the PC.
• Windows Vista: Set power-saving mode in Control Panel → Appearance and Personalization
→ Personalize → Screen Saver Settings or BIOS SETUP on the PC.
• Windows 7: Set power-saving mode in Control Panel → Appearance and Personalization →
Personalize → Screen Saver Settings or BIOS SETUP on the PC.
• Windows 8: Set power-saving mode in Settings → Control Panel → Appearance and
Personalization → Personalize → Screen Saver Settings or BIOS SETUP on the PC.
97
Chapter 11
Specifications
1 Size
2 Display area
H
V
3 Dimensions (W x H x D)
D
H
General
Model Name
Panel Size
Display area
Dimensions (W x H x D)
Weight (without stand)
Power Supply
Environmental considerations
Operating
Storage
W
ED65D
65 Class (64.5 inches / 163 cm)
ED75D
75 Class (75 inches / 189 cm)
1431.4 (H) x 806.5 (V) mm
56.4 (H) x 31.8 (V) inches
1467.5 x 848.0 x 65.0 mm
57.8 x 33.4 x 2.6 inches
1653.3 (H) x 931.3 (V) mm
65.1 (H) x 36.7 (V) inches
1675.0 x 958.5 x 65.0 mm
65.9 x 37.7 x 2.6 inches
26.8 kg / 59.1 lbs 28.8 kg / 63.5 lbs
This product uses 100 to 240V. Refer to the label at the back of the product as the standard voltage can vary in different countries.
Temperature : 32 F ~ 104 F (0 C ~ 40 C)
Humidity : 10 % ~ 80 %, non-condensing
Temperature : -4 F ~ 113 F (-20 C ~ 45 C)
Humidity : 5 % ~ 95 %, non-condensing
98
― Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor settings.
Monitor installation takes place automatically. However, you can customize the installation settings if desired.
― Panel Dots (Pixels)
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect product performance.
― This device is a Class A digital apparatus.
(USA only)
Dispose unwanted electronics through an approved recycler.
To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call, (877) 278 - 0799
99
PowerSaver
The power-saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse. Powersavign mode only functions when the product is connected to a PC with a power-saving function.
PowerSaver Normal Operation
Rating Typical Max
Power saving mode
(SOG Signal : Not
Support the DPM
Mode)
Power off Power off
(Power Button off)
Power Indicator Off Blinking On Off
Power Consumption ED65D
ED75D
215 Watts
280 Watts
180 Watts
247 Watts
235 Watts
310 Watts
1 Watts
1 Watts
1 Watts
1 Watts
0 Watts
0 Watts
― The displayed power consumption level can vary in different operating conditions or when settings are changed.
― SOG(Sync On Green) is not supported.
― To reduce the power consumption to 0, turn off the switch at the back or disconnect the power cord. Disconnect the power cable if you will not be using the product for an extended period of time (during vacation, etc.).
100
Horizontal Frequency
The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in kHz.
Vertical Frequency
The product displays a single image multiple times per second (like a fluorescent light) to display what the viewer sees. The rate of a single image being displayed repeatedly per second is called vertical frequency or refresh rate.
Vertical frequency is measured in Hz.
Preset Timing Modes
― This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product.
Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product. If the LCD product does not support 85Hz, change the vertical frequency to 60Hz using the CDT product before you exchange it with the LCD product.
Synchronization
Resolution
Horizontal Frequency 30 ~ 81 kHz
Vertical Frequency 48 ~ 75 Hz
Optimum resolution
Maximum resolution
1920 x 1080 @ 60 Hz
1920 x 1080 @ 60 Hz
The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signal transmitted from the PC does not belong to the standard signal modes, the screen may be blank with the power LED on. In such a case, change the settings according to the following table by referring to the graphics card user manual.
Resolution Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V)
IBM, 720 x 400
Horizontal Frequency
(kHz)
31.469 70.087 28.322 -/+
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
35.000
49.726
68.681
31.469
37.861
37.500
66.667
74.551
75.062
59.940
72.809
75.000
30.240
57.284
100.000
25.175
31.500
31.500
-/-
-/-
-/-
-/-
-/-
-/-
101
Resolution
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1280 x 720
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1366 x 768
VESA,1440 x 900
VESA,1600 x 900
VESA,1680 x 1050
VESA,1920 x 1080
63.981
79.976
47.712
55.935
60.000
65.290
67.500
37.879
48.077
46.875
48.363
56.476
60.023
45.000
Horizontal Frequency
(kHz)
35.156
Vertical Frequency (Hz) Pixel Clock (MHz)
60.020
75.025
59.790
59.887
60.000
59.954
60.000
60.004
70.069
75.029
60.000
56.250
60.317
72.188
75.000
108.000
135.000
85.500
106.500
108.000
146.250
148.500
65.000
75.000
78.750
74.250
36.000
40.000
50.000
49.500
Sync Polarity (H/V)
+/+
-/+
+/+
+/+
+/+
+/+
-/+
-/-
-/-
+/+
+/+
+/+
+/+
+/+
+/+
102
Chapter 12
Appendix
Contact SAMSUNG WORLD WIDE
― If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
NORTH AMERICA
U.S.A
1-800-SAMSUNG (726-7864)
CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/us http://www.samsung.com/ca (English) http://www.samsung.com/ca_fr (French)
LATIN AMERICA
ARGENTINE
BOLIVIA
BRAZIL
CHILE
COLOMBIA
0800 333 3733
800-10-7260
0800-124-421 (Demais cidades e regiões)
4004-0000 (Capitais e grandes centros)
800-SAMSUNG (726-7864)
01 8000 112 112
Bogotá 600 12 72 http://www.samsung.com.ar
http://www.samsung.com
http://www.samsung.com.br
http://www.samsung.com/cl http://www.samsung.com/co
103
LATIN AMERICA
COSTA RICA
DOMINICA
ECUADOR
EL SALVADOR
GUATEMALA
HONDURAS
JAMAICA
NICARAGUA
MEXICO
PANAMA
PARAGUAY
PERU
PUERTO RICO
0-800-507-7267
1-800-751-2676
1-800-10-7267
800-6225
1-800-299-0013
800-27919267
1-800-234-7267
001-800-5077267
01-800-SAMSUNG (726-7864)
800-7267
009 800 542 0001
0-800-777-08
1-800-682-3180 http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) http://www.samsung.com
http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) http://www.samsung.com
http://www.samsung.com/latin (Spanish) http://www.samsung.com/latin_en (English) http://www.samsung.com.py
http://www.samsung.com/pe http://www.samsung.com
104
LATIN AMERICA
TRINIDAD & TOBAGO
URUGUAY
VENEZUELA
CZECH
DENMARK
EIRE
ESTONIA
FINLAND
FRANCE
EUROPE
AUSTRIA
BELGIUM
BOSNIA
BULGARIA
CROATIA
CYPRUS
1-800-SAMSUNG (726-7864)
000 405 437 33
0-800-100-5303 http://www.samsung.com
http://www.samsung.com
http://www.samsung.com/ve
0810 - SAMSUNG (7267864, € 0.07/min)
02-201-24-18
051 331 999
07001 33 11 , share cost tariff
062 SAMSUNG (062 726 786) http://www.samsung.com
http://www.samsung.com/be (Dutch) http://www.samsung.com/be_fr (French) http://www.samsung.com
http://www.samsung.com/bg http://www.samsung.com/hr
8009 4000 only from landline
800 - SAMSUNG (800-726786) http://www.samsung.com/gr http://www.samsung.com
Samsung Electronics Czech and Slovak, s.r.o. V Parku 2343/24, 148 00 - Praha 4
70 70 19 70 http://www.samsung.com
0818 717100
800-7267 http://www.samsung.com
http://www.samsung.com/ee
030-6227 515
01 48 63 00 00 http://www.samsung.com
http://www.samsung.com/fr
105
EUROPE
GERMANY
GREECE
HUNGARY
ITALIA
LATVIA
LITHUANIA
LUXEMBURG
MONTENEGRO
NETHERLANDS
NORWAY
POLAND
PORTUGAL
ROMANIA
SERBIA
0180 6 SAMSUNG bzw.
http://www.samsung.com
0180 6 7267864*
(*0,20 €/Anruf aus dem dt. Festnetz, aus dem Mobilfunk max. 0,60 €/Anruf )
80111-SAMSUNG (80111 726 7864) only from land line
(+30) 210 6897691 from mobile and land line
06-80-SAMSUNG (726-7864) http://www.samsung.com/gr http://www.samsung.com/hu
800-SAMSUNG (726-7864)
8000-7267 http://www.samsung.com
http://www.samsung.com/lv
8-800-77777
261 03 710
020 405 888 http://www.samsung.com/lt http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
0900-SAMSUNG (0900-7267864) (€ 0,10/Min)
815 56480
0 801-172-678* lub +48 22 607-93-33 **
*(całkowity koszt połączenia jak za 1 impuls według taryfy operatora)
** (koszt połączenia według taryfy operatora)
808 20-SAMSUNG (808 20 7267)
08008 SAMSUNG (08008 726 7864) TOLL FREE No.
011 321 6899 http://www.samsung.com/pl http://www.samsung.com
http://www.samsung.com/ro http://www.samsung.com/rs
106
EUROPE
SLOVAKIA
SPAIN
SWEDEN
SWITZERLAND
U.K
CIS
ARMENIA
AZERBAIJAN
BELARUS
GEORGIA
KAZAKHSTAN
KYRGYZSTAN
MOLDOVA
MONGOLIA
RUSSIA
TADJIKISTAN
UKRAINE
0800 - SAMSUNG (0800-726 786)
902172678
0771 726 7864 (SAMSUNG)
0848 - SAMSUNG (7267864, CHF 0.08/min)
0330 SAMSUNG (7267864)
0-800-05-555
088-55-55-555
810-800-500-55-500
0-800-555-555
8-10-800-500-55-500 (GSM: 7799)
00-800-500-55-500
0-800-614-40
+7-800-555-55-55
8-800-555-55-55
8-10-800-500-55-500
0-800-502-000 http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com/ch (German) http://www.samsung.com/ch_fr (French) http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com/ua (Ukrainian) http://www.samsung.com/ua_ru (Russian)
107
CIS
UZBEKISTAN
ASIA PACIFIC
AUSTRALIA
CHINA
HONG KONG
INDIA
INDONESIA
JAPAN
MALAYSIA
NEW ZEALAND
PHILIPPINES
SINGAPORE
TAIWAN
THAILAND
8-10-800-500-55-500
1300 362 603
400-810-5858
(852) 3698 4698
1800 3000 8282
1800 266 8282
0800-112-8888 (Toll Free)
(021) 56997777
0120-327-527
1800-88-9999
0800 SAMSUNG (0800 726 786)
1-800-10-7267864 [PLDT]
1-800-8-7267864 [Globe landline and Mobile]
02-4222111 [Other landline]
1800-SAMSUNG (726-7864)
0800-32-9999
0-2689-3232,
1800-29-3232 http://www.samsung.com
http://www.samsung.com/au http://www.samsung.com
http://www.samsung.com/hk (Chinese) http://www.samsung.com/hk_en (English) http://www.samsung.com/in http://www.samsung.com/id http://www.samsung.com
http://www.samsung.com/my http://www.samsung.com/nz http://www.samsung.com/ph http://www.samsung.com/sg http://www.samsung.com/tw http://www.samsung.com/th
108
KUWAIT
MOROCCO
OMAN
PAKISTAN
QATAR
SAUDI ARABIA
SYRIA
ASIA PACIFIC
VIETNAM
MENA
ALGERIA
BAHRAIN
EGYPT
IRAN
JORDAN
1800 588 889
0800 100 100
8000-4726
08000-726786
021-8255
0800-22273
06 5777444
183-2255 (183-CALL)
080 100 2255
800-SAMSUNG (726-7864)
0800-Samsung (72678)
800-2255 (800-CALL)
920021230
18252273 http://www.samsung.com
http://www.samsung.com/n_africa http://www.samsung.com/ae (English) http://www.samsung.com/ae_ar (Arabic) http://www.samsung.com
http://www.samsung.com
http://www.samsung.com/Levant (English) http://www.samsung.com/ae (English) http://www.samsung.com/ae_ar (Arabic) http://www.samsung.com
http://www.samsung.com/ae (English) http://www.samsung.com/ae_ar (Arabic) http://www.samsung.com/pk/ http://www.samsung.com/ae (English) http://www.samsung.com/ae_ar (Arabic) http://www.samsung.com/sa http://www.samsung.com/Levant (English)
109
MENA
TUNISIA
TURKEY
U.A.E
AFRICA
BOTSWANA
BURUNDI
CAMEROON
COTE D’ IVOIRE
DRC
GHANA
KENYA
NAMIBIA
NIGERIA
MOZAMBIQUE
RWANDA
SENEGAL
SOUTH AFRICA
80-1000-12
444 77 11
800-SAMSUNG (726-7864)
8007260000
200
7095-0077
8000 0077
499999
0800-10077
0302-200077
0800 545 545
08 197 267 864
0800-726-7864
847267864 / 827267864
9999
800-00-0077
0860 SAMSUNG (726 7864) http://www.samsung.com/n_africa http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
110
AFRICA
SUDAN
TANZANIA
UGANDA
ZAMBIA
1969
0685 88 99 00
0800 300 300
0211 350370 http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
http://www.samsung.com
111
Responsibility for the Pay Service (Cost to
Customers)
― When the service is requested, in spite of in warranty, we may charge you for a visit from a service technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
• If a service technician gives instructions on how to use product or simply adjusts options without disassembling product.
• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
• If a product is reinstalled or devices are connected additionally after installing the purchased product for the first time.
• If a product is reinstalled to move to a different spot or to move to a different house.
• If customer requests instructions on how to use because of another company's product.
• If customer requests instructions on how to use the network or another company's program.
• If customer requests software installation and setup for the product.
• If a service technician removes/cleans dusts or foreign materials inside of the product.
• If customer requests an installation additionally after purchasing a product through home-shopping or online.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
• External impact or drop.
• Use of supplies or separatly sold product unspecified by Samsung.
• Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
• Remodeling or repairing the product by customer.
• Using it with incorrect voltage or non-authorised electrical connections.
• Not following the "cautions" in User Manual.
Others
• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
• If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator, Lamp,
Filter, Ribbon, etc.)
― If customer requests a service in case the product has no defect, service fee may be charged. So please read User Manual first.
112
Optimum Picture Quality and Afterimage
Burn-in Prevention
Optimum Picture Quality
• Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be brighter or darker on the panel. This does not affect product performance.
The number of sub-pixels by panel type: 6,220,800
• Run Auto Adjustment to improve the picture quality. If noise is still found even after auto adjustment, adjust Coarse or Fine .
• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels.
Activate power-saving mode or a dynamic screen saver if you will not be using the product for an extended period of time.
Prevention of Afterimage Burn-in
Black Matrix
Common
Electrode (ITO)
Color-Filter
Source Drain
TFT
Data Bus-Line
Gate
Pixel Electrode (ITO)
Storage
Capaccitor (Cs)
What is afterimage burn-in?
Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period of time (more than 12 hours), a slight voltage difference may occur between the electrodes in pixels that control the liquid crystals.
Such a voltage difference between electrodes increases with time and makes the liquid crystals thinner.
When this occurs, a previous image can remain on the screen when the pattern changes. To prevent this, the accumulated voltage difference should be reduced.
― Afterimage burn-in should not occur when an LCD panel is operating in proper conditions.
Preventing afterimage burn-in
― The best way to protect the product from afterimage burn-in is switching the power off or setting the
PC or system to run a screen saver when not in use. Also, Warranty service may be limited depending on instruction guide.
• Powering Off, Screen Saver and Power Saving Mode
Power off the product for 2 hours after using it for 12 hours.
Go to Display Properties > Power Supply on your PC and set the product to power off as required.
Using a screen saver is recommended.
It is best to use a single-color or moving-image screen saver.
• Regular color Change
Use 2 colors
Switch between 2 colors every 30 minutes as shown above.
Type 1
FLIGHT
OZ348
TIME
20:30
UA102 21:10
Type 2
FLIGHT
OZ348
TIME
20:30
UA102 21:10
113
• Avoid combinations of a text color and background color of contrasting brightness.
― Avoid using grey as it may contribute to afterimage burn-in.
― Avoid using colors of contrasting brightness (black and white; grey).
FLIGHT : TIME
OZ348 : 20:30
FLIGHT
OZ348
:
:
TIME
20:30
• Regular Text color Change
Use bright colors of similar brightness.
Interval: Change text color and background color every 30 minutes
FLIGHT : TIME
OZ348 : 20:30
FLIGHT
OZ348 :
: TIME
20:30
Move and change text every 30 minutes as shown below.
FLIGHT : TIME
OZ348 : 20:30
FLIGHT
OZ348 :
: TIME
20:30
[ Step 1 ] [ Step 2 ]
Regularly display a moving image along with a logo.
Interval: Display a moving image along with a logo for 60 seconds after using for 4 hours.
FLIGHT
OZ348 :
: TIME
20:30
FLIGHT
OZ348 :
: TIME
20:30
[ Step 3 ]
114
License
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
®
Premium Sound 5.1
Manufactured under a license from U.S. Patent No’s: 5,956,674, 5,974,380,
5,978,762, 6,487,535, 6,226,616, 7,212,872, 7,003,467, 7,272,567, 7,668,723,
7,392,195, 7,930,184, 7,333,929 and 7,548,853. DTS, the Symbol, and DTS and the Symbol together are registered trademarks & DTS Premium Sound | 5.1 is a trademark of DTS, Inc. ⓒ2012 DTS, Inc. All Rights Reserved.
DivX Certified Ⓡ to play DivX Ⓡ video up to HD 1080p, including premium content.
DivXⓇ, DivX CertifiedⓇ and associated logos are trademarks of DivX, Inc. and are used under license.
ABOUT DIVX VIDEO: DivXⓇ is a digital video format created by DivX, Inc. This is an official DivX
CertifiedⓇ device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX CertifiedⓇ device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the product menu.
Open Source Licence Notice is written only English.
For information on the Open Source License Notice, contact the Samsung Customer Center or send email to [email protected].
115
Terminology
480i / 480p / 720p / 1080i /
1080p____ Each of the scanning rates above refers to the number of effective scanning lines that decides the screen resolution. The scanning rate may be indicated in i (interlaced) or p (progressive), depending on the scanning method.
- Scanning
Scanning refers to a process of sending pixels that form an image progressively.
A larger number of pixels will deliver a clearer and more vivid picture.
- Progressive
In progressive scan mode, all lines of pixels are scanned one by one
(progressively) on the screen.
- Interlaced
In interlaced scan mode, every other line of pixels is scanned from top to bottom first and then the remaining lines of pixels (that were not scanned) are scanned.
Non-interlace Mode and Interlace
Mode____ Non-interlace mode
(progressive scan) displays a horizontal line from the top to the bottom of a screen progressively. Interlace mode displays the odd number lines first and the even number lines next. Noninterlace mode is mainly used in monitors as it produces screen clarity and interlace mode is mainly used in
TVs.
Dot Pitch____ The product and screen consist of red, green and blue dots.
A shorter distance between the dots produces a higher resolution. Dot pitch refers to the distance between the shortest distance between dots of the same color. Dot pitch is measured in millimeters.
Vertical Frequency____ The product displays a single image many times per second (like a fluorescent light that flickers) to display an image for a viewer to see. The rate of a single image being displayed repeatedly per second is called vertical frequency or refresh rate.
Vertical frequency is measured in Hz.
E.g. 60Hz refers to a single image being displayed 60 times in one second.
Horizontal Frequency____ The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in kHz.
Source____ Input source refers to a video source device connected to the product such as a camcorder or video or DVD player.
Component ports (green, blue and
red)____ The component ports, which identify, transmit and receive contrast signals, provide superior picture quality to any other video connection methods.
Plug & Play____ Plug & Play is a function that allows the automatic exchange of information between a monitor and PC to produce an optimum display environment. The product uses
VESA DDC (international standard) to execute Plug & Play.
Resolution____ Resolution is the number of horizontal dots (pixels) and vertical dots (pixels) that form a screen.
It represents the level of display detail.
A higher resolution enables more data to be displayed on the screen and is useful to perform multiple tasks simultaneously.
E.g. A resolution of 1920 X 1080 consists of 1,920 horizontal pixels (horizontal resolution) and 1,080 vertical pixels
(vertical resolution).
HDMI (High Definition Multimedia
Interface)____ It is an interface that can be connected to a digital audio source as well as a high-definition video source by using a single cable without compression.
Multiple Display Control (MDC)____
MDC (Multiple Display Control) is an application that allows multiple display devices to be controlled simultaneously using a PC. Communication between a PC and monitor takes place using
RS232C (serial data transmission) and
RJ45 (LAN) cables.
116
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project