Morphy Richards | 10 CUP FILTER COFFEE MAKER - REV 2 | Mister Cappuccino 10 Cup Filter coffee Maker

47008 rev2
24/4/06
14:42
Page 1
Mister Cappuccino 10 cup filter
coffee maker with heated frother
Please read and keep these instructions
Getting the best from your new coffee maker...
WARNING: Hot water and steam
Safety first
Caution must be used when handling hot water, coffee or steam
Run water through your machine before first use
It is important to run water through your coffee maker in order to rinse the machine. You can also
run water through to warm your coffee machine.
Descale as appropriate for the hardness of the water in your area
It is important to descale as the performance of your coffee
maker may be impaired by limescale and other impurities in the water supply.
For replacement parts, help with using your Morphy Richards, problems
and lots more, contact us by phone or through our website.
UK Helpline: 0870 060 2610
Replacement parts: 0870 167 6641
Ireland 1800 409119
www.morphyrichards.com
CM47008 Rev2
47008 rev2
24/4/06
14:42
Page 2
IMPORTANT SAFETY
INSTRUCTIONS
The use of any electrical
appliance requires the following
common sense safety rules.
•
•
Ensure the lid of the glass jug
is securely in place before
pouring.
•
Take care to pour hot coffee
slowly and carefully without
tipping the glass jug too fast.
•
Do not fill above the capacity
mark of the water level gauge
marked on the jug.
•
IMPORTANT: Damage to the
appliance! In addition we offer
the following safety advice.
Do not use the glass jug in a
microwave.
•
Milk should not be reheated,
only heat it when required.
Location
•
When heating milk, please use
stainless steel jug provided.
Remove all the packaging and
retain for future reference.
•
Do not fill milk jug above the
MAX mark.
Ensure the coffee maker is
used on a firm, flat surface.
•
Do not touch metal parts until
the unit has cooled..
Primarily there is danger of
injury or death and secondly
the danger of damage to the
appliance. These are indicated
in the text by the following two
conventions:
•
Personal safety
•
Do not use the coffee maker
outdoors or in a bathroom.
•
Do not place the coffee maker
on a highly polished wooden
surface as damage may occur
to the surface.
•
Do not fill milk jug above the
MAX mark.
•
Do not adjust the coffee
strength once brewing is in
process.•
Do not overfill the water tank.
•
The glass jug gets hot while
the machine is in use. Always
use with care.
•
Make sure the mains lead does
not touch the hot parts of the
machine.
•
Do not wind the mains lead
around the hot appliance or
store the appliance until it has
fully cooled down.
Treating scalds
•
Children
•
•
•
Do not place the coffee maker
on or near hot surfaces such
as a hot plate or radiant rings
or near a naked flame.
WARNING: Do not place the
coffee maker onto a metal tray
or metal surface whilst in use.
•
Mains lead
2
•
Disconnect the coffee maker
from the mains supply when
filling, cleaning or not in use.
•
When unplugging, turn any
control to ‘off’, then remove
plug from the wall outlet.
Never use warm or hot water
to fill the water tank.
•
Ensure the lid of the glass jug
is securely in place before
pouring.
Keep the outside of the coffee
maker area clean and dry at all
times.
•
Do not touch hot surfaces.
Always use handles or knobs.
•
Do not immerse the coffee
maker itself in water and
always ensure the electrical
connections are kept dry.
•
Do not operate any appliance
with a damaged cord or plug or
after the appliance
malfunctions or has been
damaged in any manner. Ring
the helpline number for advice
on examination and repair.
•
The use of attachments or
tools not recommended or sold
by Morphy Richards may
cause fire, electric shock or
injury.
Do not let the mains lead hang
over the edge of the worktop
where a child could reach it.
•
Do not let the lead run across
an open space e.g. between a
low socket and table.
•
•
Do not let the lead run across a
cooker or other hot area which
might damage the cable.
•
Do not fill above the capacity
mark of the water level gauge.
•
•
The mains lead should reach
from the socket to the base
unit without straining the
connections.
Do not use the glass jug in a
microwave.
•
Milk should not be reheated,
only heat it when required.
•
When heating milk, please use
stainless steel jug provided.
•
Other safety
considerations
Product safety
•
•
Children do not understand the
dangers associated with
operating electrical appliances.
Never allow children to use this
appliance.
Run cold water over the
affected area immediately. Do
not stop to remove clothing,
get medical help quickly.
Take care to pour hot coffee
slowly and carefully without
tipping the glass jug too fast.
Do not place the glass jug on
the hot plate unless the lid is in
position.
UK Helpline 0870 060 2610 Replacement Parts 0870 157 6641
Ireland Helpline 1800 409119
47008 rev2
•
24/4/06
14:42
Page 3
Do not use the coffee maker
for anything other than its
intended purpose.
Electrical
requirements
Check that the voltage on the
rating plate of your appliance
corresponds with your house
electricity supply which must
be A.C. (Alternating current).
If the socket outlets in your
home are not suitable for the
plug supplied with this
appliance the plug should be
removed and the appropriate
one fitted.
WARNING : The plug
removed from the mains
lead, if severed, must be
destroyed as a plug with a
bared flexible cord is
hazardous if engaged into a
live socket outlet.
Should the fuse in the 13 amp
plug require changing a 13
amp BS1362 fuse must be
fitted.
WARNING: This appliance
must be earthed.
⁄
¤
Ê
Â
‹
Á
›
fi
Ë
fl
È
‰
‡
„
·
‚
Features
⁄ Filter locating tab
¤ Removable permanent mesh
filter
‡ Milk frother hot plate
· Milk frother hot plate on/off
switch with indicator
‚ Coffee hot plate on/off switch
with power & ready indicators
‹ Removable filter holder with
locking tab
„ Coffee hot plate
› Non drip valve
‰ Water level indicator
fi Milk frother on/off button
 Hinged reservoir lid with
strength selector.
Á Glass coffee jug with water
level indicator
Ë Measuring spoon
È Milk frother jug
fl Milk frother attachment
Ê Jug lid
www.morphyrichards.com
3
47008 rev2
24/4/06
14:42
Page 4
OPERATING THE
APPLIANCE
Before use
otherwise the non-drip valve will not
open, causing the filter to flood.
7
Plug the filter coffee maker in at the
wall socket and push the coffee
on/off switch to ‘ON’ position. The
orange light will glow to show coffee
maker is working.
8
Hot water will start to flow through
the coffee grounds and into the glass
jug as coffee.
9
When the filtering process is
complete remove the glass jug from
your coffee maker and pour the
coffee into your cups.
Take your coffee maker out of the
box and remove the packaging.
A
Before using the appliance for the
first time, clean thoroughly by
operating two or three times with the
maximum volume of fresh water (10
cups) but without using coffee.
Wash the detachable parts of the
machine in warm soapy water.
Rib
Locating the filter
Locking tab
1
To remove the filter, slide the locking
tab on the removable filter holder to
the unlock position and lift both the
holder and mesh filter out to clean.
(see cleaning) A
2
To refit, place the removable filter
holder into the top of your coffee
maker, making sure the tab lines up
with the rib then slide the locking tab
to the lock position. Place the
permanent mesh filter inside the filter
holder by lining up the locating tab
with the groove in the filter holder as
shown
B
10 The anti-drip valve will prevent any
remaining coffee dripping onto the
hot plate. Ensure that the jug is
replaced on the hot plate after
serving. While the coffee maker is
switched ON the hot plate will keep
the coffee warm.
11 Switch off the coffee maker when the
jug is empty or the coffee is no
longer required.
WARNING: The coffee maker and
hot plates are hot and remain hot
for some time after switching off.
12 Allow unit to cool.
Making coffee
4
1
Lift up the hinged reservoir lid.
2
Fill the water reservoir with the
required amount of water using the
water level indicator as a guide. Both
the jug and water level indicator are
marked in cups. Do not exceed the
maximum level on the water
gauge.B
3
Spoon the required amount of
ground filter coffee into the mesh
filter spreading it evenly. We suggest
one level measuring spoon for every
cup. Ensure the filter is sitting
properly in the filter holder.
4
Close the reservoir lid.
5
Select the strength of coffee required
using the strength selector on the
reservoir lid.
6
Slide the jug into the coffee maker
ensuring it sits correctly on the hot
plate. The jug lid must be in place
during the brewing process,
13 Remove the permanent mesh filter
and empty the used coffee grounds.
Wash the filter immediately and dry
thoroughly. NOTE: THE MESH WILL
BECOME DISCOLOURED AFTER A
WHILE DUE TO THE STAINING
EFFECT OF COFFEE.
UK Helpline 0870 060 2610 Replacement Parts 0870 157 6641
NOTE: It is normal for the green
ready light to go out and come back
on intermittently due to thermostatic
cycling.
Ireland Helpline 1800 409119
4
47008 rev2
24/4/06
14:42
Page 5
C
Making a cappuccino
Cleaning
Prepare your machine as described
in the section ‘Making a coffee’. Use
your glass jug for measuring the
correct amount of water needed.
The milk frother blade can be wiped
clean still attached to the machine or
it can be removed for easy cleaning
by unscrewing the blade and shaft.
Wash carefully in hot soapy water.
Frothing milk
For quick cleaning just after use, fill
up the milk jug with hot water and
run the frother for 30-50 seconds;
repeat the process twice.
It is advised to start heating your
milk at the same time as heating
your coffee or several minutes before
making coffee to ensure milk is hot.
D
1
2
Fill the stainless steel milk jug
provided with the required amount of
milk. Do not exceed the maximum
level or add less than the minimum
level.
1
Place the jug on the hot plate and
switch on. C
NOTE: You can turn on the hot plate
at the same time as the coffee
hotplate. It will take approximately 57 minutes for the milk to heat up to
its optimum frothing temperature.
3
If the milk has been left for a long
time the cowl and blade can be
removed and soaked in hot soapy
water for 2-5 minutes before rinsing
clean.
The frother blade can be wiped clean
still attached to the machine.
2
Lift the milk jug up to the milk frother
blade D. Raise the milk jug ensuring
that the cowl is just under the
surface of the milk - this will give the
maximum froth. Maintain the milk jug
in this position between 30-60
seconds.
3
4
Place the milk jug back on the hot
plate to reheat the milk and preserve
the quality of the froth.
NOTE: The jug can stay on the hot
plate until the coffee has finished
brewing but be careful not to burn
your milk/froth.
5
F
6
Pour the coffee into cups and gently
pour or preferably spoon the milk
onto the coffee, then sprinkle a little
chocolate powder for the perfect
cappuccino.
If further cleaning is required the
propeller and shaft can be removed.
To replace, insert the stem of the
milk frother blade into the mounting
hole on the unit and screw into
place.F
NOTE: If the blade is removed,
ensure that it is fully tightened in
place otherwise the frother will not
operate properly.
WARNING: Take care as the milk
will be hot.
E
Remove the cowl directly after use
and rinse in warm water. E It is
recommended that you clean the
blade immediately after use, as dried
milk can be difficult to remove.
There may be some splash back of
milk on the underside of the frothing
unit. Switch the unit off then simply
wipe this area clean with a damp
cloth.
WARNING: THE FROTHER ONLY
OPERATES CORRECTLY WHEN
THE COWLING IS CORRECTLY
ASSEMBLED.
DO NOT OPERATE THE FROTHER
DRY OR NOT SUBMERSED IN
LIQUID FOR LONG PERIODS OF
TIME.
Turn off the milk frother hot plate by
pressing the on/off switch.
WARNING: the stainless steel jug
and the hotplate will remain hot
for sometime after switching off.
5
www.morphyrichards.com
5
47008 rev2
24/4/06
14:42
Page 6
RECIPIES
1
Prepare coffee as per ‘making a
coffee’ instructions.
2
Fill the stainless steel milk jug with
the required amount of milk, place on
the hotplate and switch on. The milk
will take approx.5-7 minutes to reach
the appropriate temperature.
3
Froth milk by lifting the milk jug up to
the milk frothing blade ensuring that
the blade is just under the surface of
the milk and press the milk frothing
button. The milk will take approx. 3060 seconds to froth.
4
Prepare the hot chocolate according
to the instructions.
5
Pour the coffee, hot milk and hot
chocolate into a tall glass and serve.
Cappuccino
1/3 coffee
1/3 hot milk
1/3 hot frothed milk
Chocolate powder for sprinkling
1
Prepare coffee as per ‘making a
coffee’ instructions.
2
Fill the stainless steel milk jug with
the required amount of milk, place on
the hotplate and switch on. The milk
will take approx. 5-7 minutes to
reach the appropriate temperature.
3
Froth milk by lifting the milk jug up to
the milk frothing blade ensuring that
the blade is just under the surface of
the milk and press the milk frothing
button. The milk will take approx. 3060 seconds to froth.
Irish coffee
Makes 2 servings
40ml of double cream
4
Pour the coffee in first and then the
hot milk into a cappuccino cup,
spoon over frothed milk.
2 tsp sugar
4 shots of Irish whisky
5
Sprinkle with chocolate powder to
serve.
Cafe Latte
350ml hot strong coffee
1
Whip double cream until thick then
chill.
2
Warm 2 Irish coffee glasses with hot
water and place in each a teaspoon
of sugar and 2 shots of Irish whisky.
3
Divide coffee among the glasses.
4
Slowly dribble the chilled cream over
the back of the spoon.
5
Do not stir.
1/2 coffee
1/2 hot frothed milk
1
2
Prepare coffee as per ‘making a
coffee’ instructions.
Fill the stainless steel milk jug with
the required amount of milk, place on
the hotplate and switch on. The milk
will take approx. 5-7 minutes to
reach the appropriate temperature.
Amaretto coffee
3
Froth milk by lifting the milk jug up to
the milk frothing blade ensuring that
the blade is just under the surface of
the milk and press the milk frothing
button. The milk will take approx. 3060 seconds to froth.
250ml hot strong coffee
2 tablespoons of double or whipped
cream
2 shots of Amaretto
4
Pour the coffee into a tall glass and
top with the frothed milk.
Moccacino
Sugar to taste
1
Stir the coffee and alcohol together
either with a couple of tablespoons
of double-cream, or top with a dollop
of whipped cream.
2
Sprinkle with grated chocolate and
serve.
1/3 coffee
1/3 hot frothed milk
1/3 hot chocolate
6
UK Helpline 0870 060 2614 Replacement Parts 0870 157 6645
Ireland Helpline 1800 409119
6
47008 rev2
24/4/06
14:42
Page 7
HINTS AND TIPS
soapy water. Rinse and dry all parts
thoroughly. Refit filter, filer holder,
milk frother blade, and milk frother
attachment.
CLEANING AND
MAINTENANCE
Wipe all external surfaces with a
damp cloth and dry thoroughly.
Refilling
1
2
•
Switch off the coffee maker, and
allow 5 minutes to cool.
Lift the hinged reservoir and refill
with cold water.
Care must be taken to ensure the
non drip valve situated on the
bottom of the filter holder is not
damaged during cleaning.
Descaling
Never use harsh or abrasive
cleaners.
If you live in a harder water area, we
recommend that your coffee maker
is descaled at regular intervals, eg.
every 2 - 3 months. In areas of
moderately hard water you should
descale every 6 months.
MILK FROTHER PARTS
(EXCLUDING MILK FROTHER JUG)
ARE DISHWASHER SAFE.
•
If the water filters through more
slowly than usual, it is a sign that
descaling is necessary.
•
We recommend you to use
proprietary liquid descaler which is
especially made for coffee makers
and plastic kettles. Follow the
instructions on the bottle or sachet,
and them operate the coffee maker
with just water 3 times before
making coffee.
If you have any difficulty with your
appliance, do not hesitate to call. We
are more likely to be able to help
than the store from where you
bought it.
•
Do not use kettle descaler unless the
packet specially states it is suitable
for coffee makers.
NOTE: The permanent mesh filter
should not be used during descaling.
Cleaning care
Unplug The coffee maker, and allow
to cool.
Helpline
Please have the following
information ready to enable our staff
to deal with your enquiry quickly:
•
Name of the product
•
Model number as shown on the
underside of the appliance.
•
Serial number as shown on
underside of the appliance.
For electrical products sold within
the European Community.
At the electrical products useful life it
should not be disposed of with
household waste.
Please recycle where facilities exist.
Do not immerse the coffee maker in
liquid.
Rinse the water tank occasionally
with cold water. Do not use a cloth
as any residue or lint left behind
may clog the coffee maker.
Remove the permanent filter discard
used coffee and wash with warm
soapy water. Extended soaking helps
remove coffee stains from the mesh.
Rinse and dry thoroughly.
Check with your Local Authority or
retailer for recycling advice in your
country.
UK Helpline
0870 060 210
Replacement Parts
0870 167 6641
Ireland Helpline
1800 409119
Wash the milk frother blade,milk
frother attachment, milk frother jug,
glass jug, and filter holder, in warm
7
www.morphyrichards.com
7
47008 rev2
24/4/06
14:42
Page 8
YOUR TWO YEAR
GUARANTEE
It is important to retain the retailers
receipt as proof of purchase. Staple
your receipt to this back cover for
future reference.
Please quote the following
information if the product develops a
fault. These numbers can be found
on the base of the product.
Model no.
For electrical products sold
within the European
Community. At the end of the
electrical products useful life it
should not be disposed of
with household waste.
Please recycle where facilities
exist. Check with your Local
Authority or retailer for
recycling advice in your
country.
EXCLUSIONS
Morphy Richards shall not be liable
to replace or repair the goods under
the terms of the guarantee where:
1
The fault has been caused or is
attributable to accidental use,
misuse, negligent use or used
contrary to the manufacturers
recommendations or where the fault
has been caused by power surges or
damage caused in transit.
2
The appliance has been used on a
voltage supply other than that
stamped on the products.
3
Repairs have been attempted by
persons other than our service staff
(or authorised dealer).
4
Where the appliance has been used
for hire purposes or non domestic
use.
5
Morphy Richards are not liable to
carry out any type of servicing work,
under the guarantee.
6
Plastic filters for all Morphy Richards
kettles and coffee makers are not
covered by the guarantee.
•
This guarantee does not confer any
rights other than those expressly set
out above and does not cover any
claims for consequential loss or
damage. This guarantee is offered as
an additional benefit and does not
affect your statutory rights as a
consumer.
•
This guarantee is valid in the UK and
Ireland only.
Serial no.
All Morphy Richards products are
individually tested before leaving the
factory. In the unlikely event of any
appliance proving to be faulty within
28 days of purchase it should be
returned to the place of purchase for
it to be replaced.
If the fault develops after 28 days
and within 24 months of original
purchase, you should contact the
Helpline number quoting Model
number and Serial number on the
product, or write to Morphy Richards
at the address shown.
You will be asked to return the
product (in secure, adequate
packaging) to the address below
along with a copy of proof of
purchase.
Subject to the exclusions set out
below (see Exclusions) the faulty
appliance will then be repaired or
replaced and dispatched usually
within 7 working days of receipt.If for
any reason this item is replaced
during the 2 year guarantee period,
the guarantee on the new item will
be calculated from original purchase
date. Therefore it is vital to retain
your original till receipt or invoice to
indicate the date of initial purchase.
To qualify for the 2 year guarantee
the appliance must have been used
according to the manufacturers
instructions. For example coffee
makers should have been regularly
descaled.
The After Sales Division
Morphy Richards Ltd
Mexborough, South Yorkshire,
England, S64 8AJ
Morphy Richards products are intended for household use only.
Morphy Richards has a policy of continuous improvement in product quality and
design. The company, therefore reserves the right to change the specification of its
models at any time.
Helpline (office hours)
UK 0870 060 2610
Republic of Ireland 1800 409119
CM 47008 Rev2 04/06
For details of other products in the Morphy Richards range please see our website . . .
8
www.morphyrichards.com
8
Download PDF