Clarion | MS3001 | Technical data | Clarion MS3001 Technical data

MS1001_owner's.qxd
8/23/99
6:06 PM
Page 1
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 2
ongratulations on your purchase of the Ungo Security System.
This Ungo Security System was designed in the heart of
California’s high-tech “Silicon Valley” by Ungo Security
Corporation, a subsidiary of Clarion Corporation. Since its founding in
1975, Ungo has been recognized as a pioneer and long time industry
leader in vehicle security.
C
Please read this manual thoroughly to familiarize yourself with your
system’s components and operation. Discuss any questions you might
have with your installing dealer.
Record the serial number of your Ungo system and keep all dealer
records and receipts. Be sure to discuss the installation with the dealer
so that you understand the specifics of the installation in your vehicle.
Also, do not forget to complete and mail the Product Warranty
Registration Card within 60 days of purchase and insure that the
installing dealer has stamped and signed the appropriate section in
order to properly register your warranty.
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 3
Table of Contents
1.
About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1
2.
Remote Transmitters
Remote Transmitter Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Two Car Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Adding a New Transmitter into the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
Deleting Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5
3.
Basic Operation
Remote Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Remote Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Silent Arming / Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Arming Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Passive Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Emergency Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Automatic System Rearming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Full Time System Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
4.
Other Features
Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Ignition Controlled Door Locking / Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Dome Light Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Auxiliary Function Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
Remote Car Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
Garage Door Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
Additional Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
5.
Reference Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
6.
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
7.
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 15
Note: Certain features described in this manual may require additional parts and/or labor. Also, many features of
the Ungo MS3001 / MS3200 security systems have selectable options that must be activated or programmed
during the system’s installation. These items will be identified in the following sections. Your Authorized
Ungo Dealer will be happy to discuss these features with you and help you design your system to meet your
needs.
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 1
About Your Ungo Security System
Ungo Security Systems are state-of-the-art vehicle protection systems equipped with features
designed to:
❐ Deter potential intrusions to the vehicle by continually flashing the system LED status
indicator while the system is Armed, giving a visual indication to any passer-by that the
system is equipped with a security system.
❐ Detect intrusions to the vehicle, including impacts to the vehicle’s body and glass, and
opening of the doors, trunk and hood.
❐ Alert those in the vicinity of the vehicle by sounding the system’s siren and flashing,
parking lights, and honking the horn.
❐ Inform the owner when the system has been triggered and specifically which zone was
violated. The system will also inform the user of any bad switches or sensors that may
be causing the system to function improperly.
❐ Protect both you and the contents of your vehicle with features such as panic mode,
dome light illumination, and ignition controlled door locking.
Each Ungo MS1001 System comes with:
•
•
•
•
•
•
Main Unit - the “brain” of the system.
2 - Three Button Remote Transmitters
Siren - Water resistant, high output siren that sounds when system is triggered.
Shock Sensor - Ungo Security’s patented sensor that detects both shock and motion.
Status LED - red illuminated indicator that provides system status information.
Emergency Override / Valet Switch - used to override the system in case the Remote
Transmitters become lost or stolen. Also used to temporarily disable the system when the
vehicle is being serviced or turned over to a parking attendant.
Options and Convenience Features*
The advanced design of the Ungo system incorporates a number of optional inputs and outputs
allowing you to create a customized security / convenience system by easily accommodating
many optional convenience and security features such as:
❐
❐
❐
❐
❐
❐
❐
❐
Remote Door Locking
Starter Disable
Horn Honk
Illuminated Entry / Exit
Remote Window Control
Remote Car Start
Extended Range Antenna
Power Trunk / Hatch Release
❐
❐
❐
❐
❐
❐
❐
Glass Breakage Sensor
Radar Sensor
Garage Door Receiver
Auxiliary Lighting Control
Stereo System Valet
Remote Head Lamp Control
Back-up Battery Siren
*May require additional parts and/or labor, see store for details.
MS1001 Owner’s Manual - Page 1
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 2
Remote Transmitters
Remote Transmitter Layout
Button 1
LED
Button 2
Each MS1001 system comes with 2 multifunction Remote Transmitters used to control nearly all
of the system’s features.
Each time a transmitter button is pressed, the LED will flash to indicate that a transmission is
taking place.
Button 1 Arms and Disarms the system. This Button also locks and unlocks the doors when the
system is in Valet Mode.
Button 2 controls the system’s Auxiliary Function 1, which is normally used for activating a car’s
electric trunk release.
When Button 1 and 2 are pressed together, the system will Arm or Disarm silently (without chirp
confirmation).
As an option, your installer can set system to always arm without chirp confirmation. If this is done, then
pressing Buttons 1 and 2 together will Arm or Disarm the system with chirp confirmation.
It is also possible to set individual Remote Transmitters to arm and disarm the system using
either of the Transmitters function Buttons, which is useful when a Transmitter is used to control
two systems. See Adding a Remote Transmitter into the System.
Page 2 - MS1001 Owner’s Manual
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 3
The following diagram illustrates how the Remote Transmitter controls the functions of the
system:
ARM / DISARM
F1
BUTTON 1
BUTTON 2
Two Car Operation
If you want to control two Ungo Security systems by a single Remote Transmitter, the unused
function of the Remote Transmitter can be set up by your dealer to operate another Ungo
Security system, giving you the convenience of operating multiple vehicles from a single Remote
Transmitter.
When set for two car operation, the Remote Transmitters will function as in the example below:
For more information about Two Car operation, see your Authorized Ungo Dealer.
ARM / DISARM (A)
ARM / DISARM (B)
BUTTON 1
BUTTON 2
(A) = Car 1
(B) = Car 2
MS1001 Owner’s Manual - Page 3
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 4
Adding a New Transmitter into the System
The MS1001 has the ability to recognize up to 21 individual Remote Transmitters. If the vehicle
is used by multiple drivers, each can have their own Remote Transmitter.
To add Remote Transmitters:
1. Turn on the ignition.
2. Press and hold the Override switch.
• The status LED will turn on red.
3. Within 5 seconds:
Continue holding the Override switch and Press Transmitter Button 1*
For remote arming with chirp confirmation.
--- or --Release the Override switch and Press Transmitter Button 1*
For remote arming without chirp confirmation.
• The status LED will flash once quickly to confirm that the new Remote Transmitter
has been added.
4. Turn off the ignition.
* The Button that is pressed will be the Arm/Disarm Button on that Remote Transmitter. You may program either of the
Transmitter’s function buttons to arm and disarm the system at this point.
Deleting Transmitters (Adding a Remote Transmitter and Erasing All
Other Remote Transmitters From the System)
1. Turn on the ignition.
2. Press and hold the Override switch.
• The status LED will turn on red.
Continue to hold the Override switch.
• After 5 seconds, the status LED will flash 4 times, then turn on red again.
3. Within 5 seconds:
Continue holding the Override switch and Press Transmitter Button 1*
For remote arming with chirp confirmation.
--- or --Release the Override switch and Press Transmitter Button 1*
For remote arming without chirp confirmation.
• The status LED will flash once quickly to confirm that the new Remote Transmitter
has been added.
4. Turn off the ignition.
* The Button that is pressed will be the Arm/Disarm Button on that Remote Transmitter. You may program either of the
Transmitter’s function buttons to arm and disarm the system at this point.
Page 4 - MS1001 Owner’s Manual
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 5
Battery Replacement
Your Ungo Remote Transmitter uses a 12 volt alkaline battery, which will need to be replaced
from time to time. Under normal conditions, the battery should last for up to a year before it
needs replacement.
When your Remote Transmitter’s battery is in need of replacement, you will notice a decrease in
your system’s operating range or a decrease in the brightness of the Transmitter’s LED indicator.
To change the battery, remove the 2 screws at the back of the Transmitter and carefully separate
the top and bottom halves of the Transmitter case.
Insert the new battery, making sure that the positive and negative terminals are positioned
correctly and replace the cover.
Battery Type: 23A
MS1001 Owner’s Manual - Page 5
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 6
Basic Features
Remote Arming
When Armed, the system monitors and protects 4 independent areas, or zones, including the
ignition switch, doors/hood/trunk, Shock Sensor, and an optional sensor.
To Arm the System:
1. Turn off the ignition.
2. Press Button 1.
• The siren will chirp once.*
• The doors will lock.
• The parking lights will flash once.
• The LED will turn on red, indicating the ignition, doors, hood and trunk inputs are
activated.
* The siren chirp(s) during Arming will alert you the condition of the system and vehicle when the system is
armed.
1 chirp
1 + 3 chirps
1 + 4 chirps
=
=
=
normal arming
Shock Sensor sensitivity is off
door, hood, or trunk open
During Arming, if the system detects a bad sensor or an open zone, the system will ignore that input, but keep
all other areas protected.
3. After 20 seconds:
• The LED will begin blinking, indicating that the sensor inputs are activated.
While the system is Armed, the system will trigger if:
•
•
•
•
The ignition key is turned on.
The doors, hood, or trunk is opened.
The Shock Sensor detects an impact to the vehicle or the motion of the car being raised.
A connected optional sensor is disturbed.
When triggered, the siren will sound, the horn will honk, and the parking lights will flash.
If the same input triggers the system 3 times during a single arming cycle, the system will
bypass that input, keeping the other zones protected, until the next time the system is
armed.
Page 6 - MS1001 Owner’s Manual
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 7
Remote Disarming
To Disarm the System:
Press Button 1.
• The siren will chirp twice.*
• The doors will unlock.
• The parking lights will flash twice.
• The dome light will turn on.
• The LED will turn off.
* The siren chirps during disarming will alert you if the system had been triggered while armed.
2 chirps
=
1 long chirp + 1 short chirp =
normal disarming
Tamper Alert - system was triggered
Tamper Alert
On Disarming, if the system responds with one long chirp and one short chirp, indicating the
system was triggered, the LED will flash for 60 seconds to indicate the zone that triggered the
system.
LED Flashes (60 seconds):
1 flash
2 flashes
3 flashes
=
=
=
doors, hood, or trunk
Shock Sensor
optional sensor
example: flash-flash-pause-flash-flash-pause = Shock Sensor
Silent Arming / Disarming
Each Remote Transmitters can be individually set to Arm and Disarm the system with or without
chirp confirmation at the time they are programmed into the system (see Adding a New
Transmitter into the System).
To temporarily cancel the Arming and Disarming confirmation chirps, you can Arm or Disarm the
system by pressing Buttons 1 and 2 together.
Note: The confirmation chirps will only be cancelled if the system status is normal. The chirp indications for the open
zone warning will not be cancelled when the system is Armed or Disarmed silently .
MS1001 Owner’s Manual - Page 7
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 8
Arming Mode Selection
Your system can be set in one of the following Arming Modes:
• Passive (automatic) Arming with chirp confirmation
• Active Arming (by Remote Only)
• Passive (automatic) Arming without chirp confirmation
To set the Arming Mode:
1. Turn the ignition on.
2. Within 4 seconds, press Buttons 1 and 2 together.
First push:
one chirp
Second push: two chirps
Third push:
three chirps
=
=
=
Passive Arming with chirp
Active Arming
Passive without chirp
3. Turn the ignition off to save your selection.
Passive Arming
When the Arming Mode has been set for Passive Arming, the system arms itself automatically,
each time the ignition is turned off and all of the doors, hood and trunk are closed.
To start the Passive Arming Process:
1. Turn off the ignition.*
• The status LED will begin to flash quickly.
2. Open the door and exit the vehicle.
• Once all doors are closed and the dome light is turned off, the LED will turn off.
3. After 20 seconds,
• The siren will chirp.
• The parking lights will flash.
• The doors will lock.**
• The status LED will flash red, indicating the system is armed.
4. The system is now armed.
* The ignition must have been on for at least 4 seconds before the Passive Arming sequence will begin.
** If the Passive Locking feature is selected.
To temporarily disable Passive Arming, you can turn the ignition key on then off, within 4
seconds. The status LED will stop flashing, and the system will not passively arm until the next
time the key is on for more than 4 seconds. This feature is useful for turning off passive arming
when refueling or washing your car or if you want to sit in your car and do not want the system
to arm.
Panic Mode
Allows you to instantly trigger the alarm in an emergency situation by the Remote Transmitter.
To enter Panic Mode:
1. Press and hold Button 1 for 2 seconds.
• The system will trigger.
2. Press Button 1 again to stop Panic Mode.*
If Panic Mode is not stopped by the Remote, it will automatically time out after 40 seconds, and
the system will return to its prior Armed/Disarmed state.
Page 8 - MS1001 Owner’s Manual
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 9
Emergency Override
In case your Remote Transmitter becomes inoperable, or it is lost or stolen, you can still enter
and drive your car by using the following procedure. Be sure that before you attempt this
procedure you have your ignition key ready and that you know the location of the override switch.
To override the system:
1. Unlock the door using the key.
2. Enter the vehicle.
• Because the system is armed, the system will trigger and the siren will be sounding.
3. Turn ignition key on.
4. Within, 4 seconds, press and hold the override switch.
• The system will disarm.
5. You can now start and drive the car.
Automatic System Rearming
This feature, which can be turned on during the installation, insures the security of the system by
protecting your car in case of an accidental disarm.
If your system becomes disarmed due to an accidental press of the Disarm Button, the system
will automatically rearm if no other activity is detected within one minute.
One minute after Remote Disarming, the system will alert you with a 10 second series of chirps,
then arm. (If the Passive Door Locking feature is selected during the installation, the system will
also relock the doors.)
Any of the following will cancel Automatic System Rearming:
• Turn on the ignition.
• Open the Doors, Trunk, or Hood.
• Activate the Auxiliary Function.
Automatic System Rearming is independent of Passive Arming and only takes place if the system
was Armed (actively or passively) for at least 20 seconds and then Disarmed by the Remote
Transmitter.
Full Time System Diagnostics
The system continuously monitors all protected zones, even when it is not armed, and warns you
if it detects a problem when you turn off the ignition.
1. Turn off the ignition.
2. If the siren chirps twice, the system has detected a problem.
3. The status LED will flash to indicate the zone where the problem has been detected.
1 flash
2 flashes
3 flashes
=
=
=
doors / hood / trunk
Shock Sensor
optional sensor
MS1001 Owner’s Manual - Page 9
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 10
Other Features
Valet Mode
Allows you to temporarily disable the security system when the car is being serviced or turned
over to a parking attendant.
To turn Valet Mode on or off:
1. Turn on the ignition.
2. Press and hold the override switch.
3. While holding the override switch, turn off the ignition.
• The siren will chirp once to indicate you have turned Valet Mode on.
• The siren will chirp twice to indicate you have turned Valet Mode off.
4. Release the override switch.
While Valet Mode is on, you can continue to lock and unlock your doors with the Remote
Transmitters, as well as operate the Auxiliary Functions.
For added protection, when the doors are locked by the Remote Transmitter, the system’s Starter
Disable circuit will activate and the LED will emit double flashes until the system is unlocked by
the Remote.
If the Remote Transmitter is lost, stolen, or becomes inoperable while the car is locked in Valet
Mode, you can use the Emergency Override procedure to deactivate the Starter Disable circuit.
Ignition Controlled Door Locking
For added convenience and safety, this feature automatically locks your car’s doors 10 seconds
after the ignition key is turned on and unlocks the doors when the ignition key is turned off.
To prevent you from accidentally locking your keys inside the car:
• The system will not automatically lock the doors if a door is open when the ignition key is turned on.
• The system will not automatically lock the doors if a door is opened during the first 10 seconds after the
ignition key is turned on.
Dome Light Control
As an option for increased safety and convenience, the system can be set, during the installation,
to automatically turn on the dome light when you Disarm the system, and also when you turn off
the ignition.
Illuminated Entry. The dome light will turn on for 20 seconds when the system is disarmed (or
unlocked in Valet Mode) using the Remote Transmitter.
Illuminated Exit. If the ignition key has been on for at least 10 seconds, the dome light will turn
on for 20 seconds when you turn off the ignition.
Page 10 - MS1001 Owner’s Manual
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 11
Auxiliary Function Output
The system is equipped with an Auxiliary Function output that can be used to control a variety of
additional features including, electric trunk release, remote car starter, power windows, power
sunroof, stereo system valet, garage door receiver, etc.
Auxiliary Function - momentary
Normally, this function is used to activate a power trunk release.
To operate the Auxiliary Function, press Button 2.
This function will operate regardless of whether the system is armed or disarmed and will
stay active for as long as Button 2 is held.
Sensor Defeat with Auxiliary Function (Dedicated Remote Start Mode). When your system is used with an optional
Remote Car Starter (Ungo model SAA4295), the Auxiliary Function can be selected to remotely start your car’s engine.
With the MS1001’s Dedicated Remote Start Mode enabled, when the Auxiliary Function is used to activate the Remote
Car Starter while the system is armed, the Shock Sensor and optional sensor inputs will be ignored. This will allow the
alarm to continue protecting the door and hood/trunk inputs, but prevent it from triggering due to the motion of the engine
starting and running. This feature must be enabled by your installer at the time of installation.
Sensor Defeat with Auxiliary Function (Remote Shock Sensor Bypass). If the Auxiliary Function is not used to
activate an auxiliary feature, it may be used as a remote shock sensor bypass instead. In case of extreme weather
conditions such as high winds, the Shock Sensor can be temporarily bypassed from the Remote Transmitter while the
system is armed to prevent the system from false alarming. To use this feature, Sensor Defeat with Auxiliary Function
must be enabled by your installer at the time of installation.
Remote Car Starter
When an optional Remote Car Starter (Ungo model number SAA4295) is installed into your car,
the Remote Transmitter can be used to remotely start and run your car engine to warm-up the
engine, as well as activate the heating / air conditioning system.
With the Dedicated Remote Start feature designed into the MS1001, the Remote Car Starter can
be used to start your engine even while the system is armed. When the Remote Car Starter is
activated by the Auxiliary Function, the system will receive a signal to temporarily ignore the
Shock Sensor and the optional sensor inputs, so that the system will not trigger due to the action
of the car starting or the vibration of the engine. The doors, hood, and trunk, however, remain
protected.
When the Remote Car Starter is activated, the siren will emit 5 quick chirps, indicating the ignition trigger and
sensor triggers are being temporarily disabled.
Garage Door Receiver
When an optional Garage Door Receiver (Ungo model number SAA5999) is used with your
system, the Remote Transmitters can be set to control almost any automatic garage door opener.
By adding this feature to your system, you not only add the convenience of being able to open
your garage door and activate your car security system by the same remote, but you also add
the protection of Ungo’s Varicode 2 anti-code grabbing technology to your automatic garage door
opener.
As an added benefit, by not keeping a garage door opener in your car, your garage is protected
from break-in by a thief who might break into your car to steal your garage door opener.
Additional Remote Transmitters
Additional Remote Transmitters for your MS1001 are available from your Authorized Ungo
dealer.
MS1001 Owner’s Manual - Page 11
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 12
Reference Chart
You can use this chart to quickly identify and interpret your system’s chirp indications and LED
flashes.
Output
When
Status
1 chirp
1 + 3 chirps
1 + 4 chirps
arming
arming
arming
normal arming
Shock Sensor sensitivity is off
door, hood, or trunk is open
2 quick chirps
LED double flashes
arming
Valet Mode
Valet Mode is on
Starter Defeat Activated
2 chirps
disarming
normal disarming
1 Long + 1 Short Chirp
no LED flashes
1 LED flash
2 LED flashes
3 LED flashes
disarming
after Tamper
after Tamper
after Tamper
after Tamper
5 quick chirps
while armed
Sensor Defeat Activated
Double chirps
(for 10 seconds)
1 minute after disarming
Automatic Rearming
LED flashing quickly
ignition key off
Passive Arming sequence started
Two chirps
1 LED flash
2 LED flashes
3 LED flashes
ignition key off
after Full Time Sys. Diag.
after Full Time Sys. Diag.
after Full Time Sys. Diag.
Full Time System Diagnostics
door, hood, or trunk
Shock Sensor
optional sensor
Page 12 - MS1001 Owner’s Manual
Alert
Alert
Alert
Alert
Tamper Alert - system was triggered
ignition
door, hood or trunk
Shock Sensor
optional sensor
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 13
Technical Data
Specifications
Main Unit
Voltage: 12v, negative ground
Current Consumption: <13.5mA
Temperature Range: -40oF to +170oF
-40oC to +77oC
Auxiliary Output Capability: 150mA
Internal Relays: 12/28A
Transmitter
Current Consumption: <.002mA, standby
Battery Type: miniature 12v, type 23A
FCC ID:
MP62VUUUNGO1001
HP92VUUNGO603/03
THIS DEVICE COMPLIES WITH FCC RULES PART 15.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE THAT MAY BE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Ungo Security Corporation
Gardena, CA
USA
Warranty Information
Model No.: MS1001 (circle one)
Serial No.:
Dealer Name:
Address:
Purchase Date:
MS1001 Owner’s Manual - Page 13
MS1001_owner's.qxd
8/23/99
Notes
Page 14 - MS1001 Owner’s Manual
6:06 PM
Page 14
MS1001_owner's.qxd
8/23/99
6:06 PM
Page 15
Warranty Information
1. Ungo Security Corporation of Gardena, California ("Ungo
Security") warrants this Ungo System to be free from defects
in materials and workmanship and to comply with Ungo
Security’s applicable printed specifications.
2. Ungo Security Systems carry a limited lifetime warranty on
the Main unit (system brain) and transmitters. The warranty
is limited to Ungo Security Systems that have been installed
by an approved Ungo dealer and is extended to the Original
Purchaser ("Owner") and to the original vehicle in which it
was installed only, and is not transferable to any subsequent
owner or owners of the product(s).
All other products (including those products of other
manufacturers which are supplied by Ungo Security as a part
of, or an accessory to, an Ungo Security-manufactured
product) are warranted by Ungo Security for a period of one
year from the date of sale to the Owner. For specific
identification of such products contact Ungo Security.
3. This warranty shall not cover: (I) any damage caused by
Owner’s negligence or misuse of any kind, or any damage
due to causes unrelated to Ungo Security’s manufacturing,
including, but not limited to improper servicing or repair by
someone other than Ungo Security or an authorized service
facility: (II) alterations or modifications to the Ungo System
other than the addition of an authorized accessory: or (III)
improper installation or removal from the vehicle contrary to
Ungo Security’s instructions.
4. Obligations of Ungo Security. In the event the Owner’s
Ungo System does not comply with this warranty, it must be
returned to Ungo Security as specified below. Ungo Security
will repair or replace it with a new or reworked unit, within
thirty (30) days of receipt and acceptance of such defective
unit, and without cost to Owner.
5. To make a claim under the warranty. Owner must: (I)
provide Ungo Security with written notice that the Ungo
System does not comply with the warranty within thirty (30)
days from the date of the Owner’s discovery of the defect and
(II) furnish proof of purchase and purchase date (this
requirement is satisfied if Ungo Security has a completed
warranty registration card on file).
6. Owner obligations. To obtain Warranty Service, Owner
must at Owner’s expense: (I) have the Ungo System
removed from the vehicle by an authorized Ungo Security
dealer, (II) package the unit in a reasonable manner to
prevent damage to the unit during shipment; and (III) ship the
unit, freight prepaid, to Ungo Security’s factory or other
authorized repair facility.
7. Repair facility locations. To obtain the name, address and
phone number of the nearest Authorized Ungo Repair Facility,
Owners may contact Ungo Security at 310-327-9100.
8. The Owner of Ungo Systems in California has the right to
have the product serviced or repaired during the warranty
period. The warranty period will be extended for the number
of full days that the product has been out of the Owner’s
hands for warranty repairs. If a defect exists within the
warranty period, the warranty will not expire until the defect
has been fixed. The warranty period will also be extended if
the repair has not been performed due to delays caused by
circumstances beyond the control of the Owner, or if the
warranty repairs did not remedy the defect and the Owner
notifies Ungo Security or the seller of the failure of the
repairs within sixty (60) days after they were completed. If,
after a reasonable number of attempts, the defect has not
been fixed the Owner may return this product for
replacement or a refund, subject in either case, to a
deduction of a reasonable charge for usage. The time
extension does not effect the protection or remedies the
Owner has under other laws.
9. Exclusions from liability.
(A) In no event shall Ungo Security be liable for any loss or
damages beyond the original purchase price of the Ungo
System , and Ungo Security specifically excludes any and all
incidental and consequential damages, whether resulting
from breach of warranty or contract, negligence or other
conduct in connection with any sale, use, servicing or repair
of a unit. (Some states do not allow the exclusion of
incidental or consequential damages, so the above
exclusion may not apply to you.)
(B) There are no warranties, express, statutory or implied,
which extend beyond that which is described herein, and in
particular, all implied warranties of merchantability and
fitness for a particular purpose, and all warranties of title and
against encumbrances, are expressly disclaimed, limited
and excluded as permitted by law; but in no event shall any
implied warranty, whether of merchantability of fitness for a
particular purpose or otherwise, have a duration exceeding
that of the express warranty made herein. (Some states do
not allow limitation on how long an implied warranty lasts, so
the above limitation may not apply to you.)
(C) No agent, officer, employee or representative of Ungo
Security, or any other person, has authority to make any
representations, promises or warranties respecting Ungo
Systems and their authorized accessories.
(D) Owner has the right to bring any action at law or in equity
to resolve disputes concerning, or to enforce, the provisions
of this warranty. No action at law or in equity may be brought
against Ungo Security for breach of warranty or contract or
based on negligence of other conduct more than three (3)
years from the date the cause of action has occurred.
(E) This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
(F) The remedies extended herein are the sole and
exclusive remedies available to Owners of Ungo Systems.
(G) Under no circumstances should this warranty, or the
products covered by it, be construed as an insurance policy
against loss.
MS1001 Owner’s Manual - Page 15
MS1001_owner's.qxd
8/23/99
6:07 PM
Page 16
Ungo Security Corporation
A Clarion Company
661 West Redondo Beach Blvd.
Gardena, CA 90247
800-Go-Clarion
www.clarionmultimedia.com
© Ungo Security Corporation, Gardena, CA
97-MS1001-10 Rev. 2 (1/99)
Download PDF