Mitsubishi | SRK20ZJ-S | User`s manual | Mitsubishi SRK20ZJ-S User`s manual

USER’S MANUAL
AIR-CONDITIONER
ENGLISH
MANUEL DE L’UTILISATEUR
FRANÇAIS
CLIMATISEUR
ANWENDERHANDBUCH
DEUTSCH
¨T
KLIMAGERA
ISTRUZIONI PER L’USO
SRK20ZJ-S
SRK25ZJ-S
SRK35ZJ-S
SRK50ZJ-S
ITALIANO
CONDIZIONATORE D’ARIA
MANUAL DEL PROPIETARIO
ESPAN˜OL
ACONDICIONADOR DE AIRE
GEBRUIKERSHANDLEIDING
NEDERLANDS
AIRCONDITIONING
MANUAL DO UTILIZADOR
PORTUGUÊS
APARELHO DE AR CONDICIONADO
ΟΔΗΓΙΕΣ ΧΡΗΣΗΣ ΕΛΛΗΝΙΚΑ
ΚΛΙΜΑΤΙΣΤΙΚΟ
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
РУССКИЙ
КОНДИЦИОНЕР ВОЗДУХА
KULLANIM KILAVUZU
AIR-CONDITIONING & REFRIGERATION SYSTEMS HEADQUARTERS
16-5, 2-Chome, Kounan, Minato-ku, Tokyo, 108-8215, Japan
Fax: (03) 6716-5926
MITSUBISHI HEAVY INDUSTRIES EUROPE, LTD.
AIR-CONDITIONER DIVISION
3rd Floor Thavies Inn House 3-4 Holborn Circus London EC1N 2HA, ENGLAND
Phone: 44(0)20 7842 8171
Fax: 44(0)20 7842 8104
RKY012A006_Cover_2009-0611
1
This air conditioner complies with EMC Directive 2004/108/EC,
LV Directive 2006/95/EC.
Este acondicionador de aire cumple con la directiva EMC: 2004/
108/EC, LV Directiva 2006/95/EC.
Ce climatiseur est conforme à la Directive EMC: 2004/108/EC, LV
Directive 2006/95/EC.
Deze airconditioner voldoet aan EMC Directive 2004/108/EC, LV
Directive 2006/95/EC.
Dieses Kimagerät erfüllt die EMC Direktiven 2004/108/EC, LV
Direktiven 2006/95/EC.
Este aparelho de ar condicionado está em conformidade com a
Directiva EMC 2004/108/EC e a Directiva LV 2006/95/EC.
Questo condizionatore d’aria è conforme alla Direttiva EMC: 2004/
108/EC, LV Direttiva 2006/95/EC.
∞˘Ùfi ÙÔ ÎÏÈÌ·ÙÈÛÙÈÎfi Â›Ó·È Û‡ÌʈÓÔ Ì ÙȘ ÚԉȷÁڷʤ˜ Ù˘
√‰ËÁ›·˜ EMC 2004/108/EK Î·È Ù˘ √‰ËÁ›·˜ LV 2006/95/EK.
TÜRKÇE
RLA012A013
07/14/2009, 14:10
Thank you for purchasing a MITSUBISHI HEAVY INDUSTRIES, LTD. Air-Conditioner. To
get the best long-lasting performance, please read and follow this User’s Manual carefully
before using your air-conditioner. After reading, please store the Manual in a safe place
and refer to it for operational questions or in the event of any irregularities.
This air-conditioner is intended for domestic use.
Do not vent R410A into the atmosphere: R410A is a fluorinated greenhouse gas,
covered by the Kyoto Protocol with a Global Warming Potential (GWP) = 1975.
ENGLISH
Your Air Conditioning product may be marked with this symbol. It means
that waste electrical and electronic equipment (WEEE as in directive 2002/
96/EC) should not be mixed with general household waste. Air conditioners
should be treated at an authorized treatment facility for re-use, recycling
and recovery and not be disposed of in the municipal waste stream. Please
contact the installer or local authority for more information.
This symbol printed in the batteries attached to your Air Conditioning
product is information for end-users according to the EU directive 2006/66/
EC article 20 annex II.
Batteries, at their end-of-life, should be disposed of separately from general
household waste. If a chemical symbol is printed beneath the symbol
shown above, this chemical symbol means that the batteries contain a
heavy metal at a certain concentration. This will be indicated as follows:
Hg:mercury(0.0005%) , Cd:cadmium(0.002%) , Pb:lead(0.004%)
Please, dispose of batteries correctly at your local community waste
collection or the recycling center.
contents
Safety precautions........................................... 2
OFF-TIMER operation ................................. 11
Name of each part and its function ................. 4
ON-TIMER operation................................... 12
Remote control handling ................................ 6
SLEEP TIMER + ON-TIMER operation ..... 12
Operation failure with the remote control ...... 6
PROGRAM TIMER operation ..................... 13
Temporary run operation ................................ 6
Operation and display section for remote
ALLERGEN CLEAR operation ................... 13
HIGH POWER/ECONOMY operation ........ 14
control ............................................................. 7
SELF CLEAN operation .............................. 15
Current time setting ........................................ 7
Auto restart function ..................................... 15
AUTO mode operation ................................... 8
Tips for effective operation .......................... 15
Temperature adjustment during AUTO .......... 8
Installation location setting ........................... 16
FAN SPEED ................................................... 8
Maintenance.................................................. 17
COOL/HEAT/DRY/FAN mode operation ..... 9
Proper installation ......................................... 19
Air-conditioner operable
Troubleshooting ............................................ 19
temperature setting ......................................... 9
Characteristics of HEAT mode operation ...... 9
Notice ........................................................... 20
Contact your dealer ....................................... 21
Airflow direction adjustment ........................ 10
About the Multiple Air-conditioner .............. 21
3D AUTO operation ..................................... 10
Self diagnosis function ................................. 22
SLEEP TIMER operation ............................. 11
–1–
RLA012A013_EN_001-022
1
08/04/2009, 10:44
Safety precautions
• Before starting to use the system, please read these “Safety precautions” carefully to ensure proper operation of the system.
• The safety precautions are classified as “ DANGER” and “ CAUTION”. Precautions as shown in the column “ DANGER” indicate that
improper handling could lead to drastic result like death, serious injury, etc. Even precautions as shown in the column “ CAUTION” might pose
a serious problem, depending on the circumstances. Please observe these precautions with great care, since they are essential to your safety.
• Symbols which appear frequently in the text have the following meaning:
Observe instructions with
great care
Strictly prohibited
Provide proper earthing
• When you have read this instruction manual, please keep it without missing. If someone else takes over as operator, make certain that the manual is
also passed on to the new operator.
❚ INSTALLATION PRECAUTIONS
DANGER
CAUTION
Do not install it where flammable gas
may leak.
The system is for domestic, residential
etc. use.
If used in severer environments, such
as an engineering workplace, the
equipment may function poorly.
Gas leaks may cause fire.
The system must be installed by your
dealer or a qualified professional.
Make sure to install the drain hose
properly so that all the water is
drained out.
It is not advisable to install the system
by yourself, as faulty handling may
cause leakage of water, electric shock
or fire.
Improper installation may lead to
water drop in the room resulting in
wet furniture.
Depending on the place of installation,
an earth leakage breaker may be necessary.
If you do not install an earth leakage
breaker, you may get an electric shock.
Make sure that the system has been
properly earthed.
Earth cables should never be connected
to a gas pipe, water pipe, lightning conductor or telephone earth cable. Incorrect installation of the earth cable may
produce an electric shock.
❚ OPERATION PRECAUTIONS
DANGER
Do not expose yourself to the cooling
air for a long period.
This could affect your physical condition and cause health problems.
Do not insert anything into the air inlet.
Store the remote control out of reach
of infants.
This may cause injury, as the internal fan rotates at high speed.
Failure to observe this may result in
the batteries being swallowed or
other accidents.
CAUTION
Only use approved fuses.
Do not handle the switches with wet
hands.
Use of steel or copper wire instead of
an approved fuse is strictly prohibited, as it may cause a breakdown or
fire.
This may cause an electric shock.
Do not place a flammable insecticide or
paint spray near the blower, nor spray it
directly on the system.
You should not expose any combustion appliance directly to the air
stream of the air-conditioner.
This may result in a fire.
Do not swing from the indoor unit.
If the indoor unit falls down,
you may get injured.
Do not wash the air-conditioner with water.
The appliance may then work inadequately.
This could cause an electric shock.
The system should only be used for its original purpose
and not for anything else like, for instance, preservation of
food, plants or animals, precision devices or works of art.
Do not place anything containing water, like vases, on top of the unit.
Do not install the system where the
airflow direction is aimed directly at
plants or animals.
The system is only intended for use in
ordinary domestic rooms. Any other
use of the system may damage the
quality of food, etc.
Water entering the unit could damage the insulation and therefore
cause an electric shock.
This will damage their health.
–2–
RLA012A013_EN_001-022
2
08/04/2009, 10:44
❚ Safety precautions
CAUTION
Do not sit on the outdoor unit nor put
anything on it.
After a long period of use, check the unit's
support structure from time to time.
If the unit falls down or things drop
off it, people could get hurt.
If you do not repair any damage
right away, the unit may fall down
and cause personal injury.
Do not place household electrical appliances or household items under neath
the indoor or outdoor units.
Do not operate the system without the
air filter.
Condensation falling from the unit
may stain objects and cause accidents
or electrical shock.
It can cause malfunction of the system due to clogging of the heat exchanger.
Do not control the system with main
power switch.
If you operate the system together
with a combustion appliance, you
must regularly ventilate the indoor air.
It can cause fire or water leakage. In
addition, the fan can start unexpectedly, which can cause personal injury.
Insufficient ventilation may cause
accidents due to oxygen deficiency.
When you clean the system, stop the
unit and turn off the power supply.
Do not place objects near the outdoor
unit or allow leaves to gather around
the unit.
Never open the panel while the
internal fan is rotating.
If there are objects or leaves around
the outdoor unit, small animals
may enter unit and contact electrical parts and may cause a breakdown, smoke or fire.
Do not touch the aluminum fins on the
air heat exchanger.
It may result in injury.
Do not shut off the power supply immediately after stopping the operation.
Wait at least 5 minutes, otherwise
there is a risk of water leakage or
breakdown.
Stand firmly on a stepladder or other
stable object when removing the inlet
panel and filters.
Failure to observe this may result in
injury through insecure objects toppling over.
Contact your dealer to clean inside
the indoor unit, do not attempt to do
by yourself.
The use of a non-approved detergent
or improper washing method may
damage the unit’s plastic components and cause leaks. Damage,
smoke, or fire may also happen if the
detergent comes in contact with
electrical parts or the unit’s motor.
Stop the unit and turn off the power if
you hear thunder or there is a danger of
lightning.
It may damage the unit.
❚ PRECAUTIONS FOR RELOCATION OR REPAIRS
DANGER
Do not perform any repairs or modifications by yourself. Consult the dealer if
the unit requires repair.
If you repair or modify the unit, it can
cause water leaks, electric shocks or
fire.
If you notice anything abnormal (smell of
burning, etc.), stop the system, turn off
the power supply and consult your dealer.
Continued use of the system in abnormal circumstances may result in
malfunctioning, electric shock, fire,
etc.
Consult your dealer for repairs.
In case the air-conditioner is relocated
elsewhere, contact your dealer or a
professional fitter.
Faulty installation may cause water
leakage, electric shock, fire, etc.
Wrong repairs could cause an electric
shock, fire, etc.
If the air-conditioner fails to cool or warm the room, it may have a refrigerant
leakage. Contact your dealer.
If refrigerant needs to be added, check with your dealer for proper instructions.
The refrigerant used in your air-conditioner is safe. However, if refrigerant unexpectedly
leaks from the unit onto a fan heater, stove, hotplate or other heat source, harmful gases could
be generated.
–3–
RLA012A013_EN_001-022
3
08/04/2009, 10:44
Name of each part and its function
INDOOR UNIT
Air Inlet panel
Draws the indoor air.
Page 17
Air filter
Removes dust or dirt from the inlet air.
Page 17
Air-cleaning filter
Page 18
Room temperature sensor
Heat exchanger
Air outlet
Air blows out of here.
Indoor unit fan
Left/right airflow direction adjustment louver
Page 10
Up/down airflow direction adjustment flap
Page 10
Drain hose
Drains water from the indoor unit.
Refrigerant piping connection and electric wire
OUTDOOR UNIT
Air inlet
(On side & rear surface)
Air outlet
Outdoor unit fan
Heat exchanger
–4–
RLA012A013_EN_001-022
4
08/04/2009, 10:44
Name of each part and its function
Unit display section
Remote control signal receiver
Unit ON/OFF button
This button can be used for turning on/off the unit when remote
control is not available.
Page 6
RUN (HOT KEEP) light (green)
3D AUTO light (green)
• Illuminates during operation.
Illuminates during 3D AUTO operation.
• Blinks when airflow stops due to the ‘HOT
KEEP’ and ‘CLEAN operation’.
HI POWER light (green)
1.5 sec.
HOT KEEP
Illuminates during HIGH POWER operation.
ON
TIMER light (yellow)
OFF
0.5 sec.
3 sec.
CLEAN operation
Illuminates during TIMER operation.
ON
OFF
1 sec.
Page 15
NOTE
• Buzzer sound for remote control
When preset temperature 24°C, automatic operation and automatic airflow are selected, the buzzer sound (PiPi) is produced.
When turning off the air conditioner by pressing ON/OFF button (except CLEAN mode), the buzzer sound (Pi) is produced.
This function is useful for operating the air conditioner in the darkness.
Air flow setting
Preset temperature
–5–
RLA012A013_EN_001-022
5
08/04/2009, 10:44
Remote control handling
Replacing the batteries
The following cases signify exhausted batteries. Replace old batteries with new ones.
• Receiving beep is not emitted when a signal is transmitted.
• Display fades away.
NOTE
1
2
Pull out the cover and take out
old batteries.
• Do not use old and new batteries together.
• Remove the batteries when the remote control is not used for a long period.
• The recommended effective period of a battery conforming to JIS or IEC should be
6 to 12 months with normal use. If used longer, or when an unspecified battery is
used, liquid may leak from the battery, causing the remote control to malfunction.
• The recommendable effective period is printed on the battery. This may be shorter
due to manufacturering time to the unit. However, the battery may still be in
working order after expiry of its nominal life.
Insert new batteries.
R03 (AAA, Micro) x2
Pay attention to
the ª and ·
marks
■ When the display shows any abnormal condition, Press the ACL switch with
the tip of a ballpoint pen.
Using the remote control holder
3
4
Close the cover.
The remote control can be attached to a wall or pillar by
using a remote control holder. Before installing the remote
control, check that the air-conditioner receives the signals
properly.
Press the ACL switch with the
tip of a ballpoint pen.
For installing or removing the remote control, move it up or
down in the holder.
The timer setting mode is displayed.
Page 7
Warning note for remote control handling
Strictly prohibited
• Do not go near high temperature
places, such as an electric carpet
or stove.
• Do not leave the remote control exposed to direct sunlight or other
strong lighting.
• Do not drop the remote control.
Handle with care.
• Do not put any obstructing obstacles between the remote control
and the unit.
• Do not spill any liquid on the
remote control.
• Do not place heavy objects on the
remote control, or step on it.
Operation failure with the remote control
• Are the batteries running down?
“Replacing the batteries” above.
Replace the batteries with new ones and retry the operation.
• If the operation fails, operate the unit with
temporary operation function.
Contact your dealer to have the remote control
checked.
Below
Temporary run operation
• The unit ON/OFF button on the unit operates ON/OFF temporarily when the remote control is not used.
Operation program
• OPERATION MODE :
AUTO
• FAN SPEED
:
AUTO
• AIR FLOW
:
AUTO
• Operation starts by pressing the unit ON/OFF button; it stops if you press
the button again.
Unit ON/OFF button
NOTE
• Do not hold the Unit ON/OFF button down for more than 5 seconds.
(Holding it down longer than 5 seconds sets the automatic cooling used during servicing or when relocating the air-conditioner.)
–6–
RLA012A013_EN_001-022
6
08/04/2009, 10:45
Operation and display section for remote control
Operation section
FAN SPEED button
OPERATION MODE select button
Each time the button is pressed, the
display is switched over in turn.
Each time the button pressed, the
display is switched over in turn.
Page 8, 9
Page 8
ON/OFF (luminous) button
HI POWER/ECONO button
Press to start operation, press again to
stop.
This button changes the HIGH POWER/
ECONOMY mode.
Page 14
AIR FLOW (UP/DOWN) button
This button changes the air flow (up/down)
direction.
Page 10
TEMPERATURE button
These buttons set the room temperature.
(These buttons are used for setting the
current time and timer function as well.)
AIR FLOW (LEFT/RIGHT) button
This button changes the air flow (left/right)
direction.
Page 10
ON TIMER button
This button selects ON TIMER operation.
3D AUTO button
Page 12
This button sets 3D AUTO operation.
Page 10
SLEEP button
OFF TIMER button
This button selects SLEEP operation.
This button selects OFF TIMER operation.
Page 11
Page 11
ACL switch
CLEAN switch
This switch is for resetting microcomputer
and setting time.
Page 6
This switch selects the CLEAN mode.
Page 15
• The above illustration shows all controls, but in practice
only the relevant parts are shown.
CANCEL button
ALLERGEN CLEAR button
This button selects ALLERGEN CLEAR
operation.
Page 13
This button cancels the ON timer, OFF
timer, and SLEEP operation.
Transmission procedure
When each button on the remote control is pressed – with the remote control pointing towards the air-conditioner unit a signal is transmitted.
When the air-conditioner receives the signal correctly, it will beep.
Current time setting
■ When inserting the batteries, the current time is automatically set to time setting mode.
13:00 is displayed as the current time. Set the clock to the right time.
Example: Set to 10:30.
1
Press the ACL switch.
2
Press the “
Press with the tip of a ballpoint pen, etc.
The time display blinks and can be set to the current time.
or
” button.
(Set to 10:30)
3
Press the ON/OFF button.
The display changes from blinking to steady lighting and the setting is complete.
Make sure to press the button within 60 seconds from the last operation in step 2,
otherwise the time is not set.
NOTE
• The timer operation works based on the time clock, so please set it correctly.
• The remote control data is reset when the present time is set.
–7–
RLA012A013_EN_001-022
7
08/04/2009, 10:45
AUTO mode operation
■ Automatically selects the operation mode (COOL, HEAT, DRY) depending on the room temperature when switched on.
When the unit is not in AUTO mode:
1
Press MODE button.
Move the [
mark] to the
(Auto) position.
Point the remote control toward the air-conditioner, and
2
Press the ON/OFF button.
To stop:
Press the ON/OFF button.
NOTE
AUTO mode can be
operated by simply
pressing the ON/OFF
button.
• In case air is not blowing out during
the operation.
Page 20
• When the included clean filter is installed the air conditioner will clean
the air during automatic operation.
• If you do not want the AUTO mode program, change to
COOL, HEAT, DRY or FAN instead of AUTO.
Display in OFF status
• The current time and preset OPERATION MODE are displayed while the
air conditioner is turned off.
Page 9
• Airflow direction adjustment procedure.
Page 10
Temperature adjustment during AUTO
■ Air temperature adjustment is possible even during automatic operation. There are 6 levels of adjustment possible with the
During automatic operation, 24ºC is preset both for heating and cooling.
button or the
button.
When a change in temperature is required.
1
Press the
or
button.
When it is a little cold
button.
Press the
button is pressed, the switch over occurs in the following order
■ Each time the
–6 → –5 → ............ –1 → ±0 → +1 ............ +6.
When +6 is indicated, even if the button is pressed, the indicator does not change.
When it is a little hot
button.
Press the
■ Each time the
button is pressed, the switch over occurs in the following order
+6 → +5 → ............ +1 → ±0 → –1 ............ –6.
When –6 is indicated, even if the button is pressed, the indicator does not change.
Setting
temp.(ºC)
-6
18
-5
19
-4
20
-3
21
Remote Control display
+0 +1
-2
-1
+2
22 23
24 25
26
+3
27
+4
28
+5
29
FAN SPEED
■ You can choose the capacity of your air-conditioner
when heating mode, cooling mode or fan mode.
Operation capacity by your choice
Press the FAN SPEED button.
Move the [
FAN SPEED
Set automatically by microcomputer
AUTO
Powerful operation with high capacity
Standard operation
Energy-saving operation
HI
MED
LO
AUTO
mark] to the preferred fan speed position.
HI
MED
NOTE
• When changing FAN SPEED from HI to LO, the sound of
refrigerant flowing may be heard.
–8–
RLA012A013_EN_001-022
8
LO
08/04/2009, 10:45
+6
30
COOL/HEAT/DRY/FAN mode operation
Point the remote control toward the air-conditioner, and
1
Press the MODE select button.
Move the [
(Cool),
2
3
mark] to the required operation position.
(Heat),
(Dry),
(Fan)
Press the ON/OFF button.
Press the TEMP button.
Press
or
button for the preferred temperature.
Standard
4
Airflow direction adjustment procedure.
Press the FAN SPEED button
Set the fan speed as preferred.
Page 10
NOTE
To stop:
Press the ON/OFF button.
• In case air is not blown out, when starting the heating operation.
Page20
• The operation program can also be set or changed when the airconditioner is not in operation.
Air-conditioner operable temperature setting
■ Use within the following operational range. Operating outside of this range may result in the protection devices being activated, preventing the
unit from working.
Cooling operation
Heating operation
Outside temperature Approximately -15 to 46 °C
Inside temperature
Inside humidity
Approximately -15 to 21 °C
Approximately 18 to 32 °C
Approximately 15 to 30 °C
Below approximately 80%
The long-term use of the unit with a humidity level
exceeding 80% may result in condensation forming on the
surface of the indoor unit, leading to water drips.
—
Characteristics of HEAT mode operation
Mechanism and capacity of HEAT mode operation
■ Mechanism
• The unit draws heat from the cold outside air, transfers it to indoors and heats the room. As a characteristic of heat pump system, the heating capacity
reduces when the outside air temperature gets colder.
• It may take some time to supply hot air after turning on the air-conditioner.
• If the outside temperature becomes extremely low, it would be better to use an additional source of heating.
Defrosting
If the outside temperature becomes low and humidity is high, the heat exchanger in the outdoor unit may frost over, which prevents efficient heating.
If this happens, the automatic defrost function is activated and during defrosting the heating operation stops for 5 to 15 minutes
during defrosting.
• Both indoor and outdoor fans stop and the RUN light blinks slowly (1.5 sec. ON, 0.5 sec. OFF) during defrosting.
• The outdoor unit may give off some steam during defrosting. This is to help the defrosting process and is not a defect.
• The HEAT operation resumes as soon as defrosting has been completed.
–9–
RLA012A013_EN_001-022
9
08/04/2009, 10:45
Airflow direction adjustment
Adjusting airflow direction
■ Up/down direction can be adjusted with the AIRFLOW
mode changes as follows:
Change on AIRFLOW (UP/DOWN) mode.
(UP/DOWN) button on the remote control. Every time you press this button the
(Flap stopped)
■ Left/right direction can be adjusted with the AIRFLOW
mode changes as follows:
Change on AIRFLOW (LEFT/RIGHT) mode.
(Swing)
(LEFT/RIGHT) button on the remote control. Every time you press this button the
(Louver stopped)
NOTE FOR HEATING OPERATION
(Swing)
• When operation starts, the flap and louver direction is fixed at the horizontal / center position in order to avoid cold draft, and return to the set the position that was
set after the warm air supply is starting.
• The flap and louver direction will be controlled to the horizontal/center position when the room temperature reaches the set temperature and compressor stops or
when defrosting is in operation.
• The airflow direction cannot be set during the period mentioned above. Change the airflow direction settings after the warm air is supplied and the flap/louver goes
to the set position.
MEMORY FLAP (FLAP OR LOUVER STOPPED)
When you press the AIRFLOW (UP/DOWN or LEFT/RIGHT) button once while the flap or louver is
operating, it stops swinging at the position. Since this angle is memorized in the microcomputer, the
flap or louver will automatically be set at this angle when the next operation is started.
• Recommended angle of the flap when stopping
DANGER
• Do not expose directory to airflow from the air-conditioner for a long time.
HEAT
CAUTION
• When in COOL or DRY operation, do not operate for a long period with the
airflow blowing straight down. Otherwise, condensation may appear on the outlet
grill and drip down.
• Do not try to adjust the flaps and louvers by hand, as the control angle may
change or the flap or louver may not be closed completely.
COOL, DRY
– 10 –
RLA012A013_EN_001-022
10
08/04/2009, 10:45
(Slant forward
blowing)
(Horizontal
blowing)
SLEEP TIMER operation
■ The unit stops automatically after the set time lapses.
The set temperature is automatically adjusted according to the elapsed time in order to avoid too much cooling or heating.
1
Page 13
Press the SLEEP button.
■ If it is pressed while the unit is off
SLEEP TIMER operation starts with the previous operation settings, and the air
conditioning is turned off after the set time elapses.
■ If it is pressed while the unit is running
The air conditioner is turned off after the set time elapses.
Every time the button is pressed, the display changes as follows:
... (Units of one hour)
No indication
(cancelled)
Example: You prefer it to stop after 7 hours.
Set to
The timer light (yellow) is on.
h
• The unit stops after the set time lapses.
Changing of set time
Set a new time by pressing SLEEP button.
NOTE
How to cancel
Press the CANCEL button to turn off the SLEEP indicator.
• SLEEP operation will not function during ALLERGEN CLEAR operation.
• Cannot be set at the same time with OFF-TIMER.
OFF-TIMER operation
■ The unit stops automatically when the set time comes.
With the air conditioner turned off, start the operation from Step 1. With the air conditioner running, start from Step 2.
Example: You prefer it to stop 22:30.
1
2
3
Press the ON/OFF button.
Press the OFF TIMER button.
OFF TIMER display
is blinking.
Press the “
or
” button.
Every time the
button is pressed, the display is switched in the order of:
0:00
0:10
Every time the
0:00 23:50
0:20
...
1:00
1:10
(Units of ten minutes)
button is pressed, the display is switched in the order of:
23:40
... 23:00
22:50
(Units of ten minutes)
Set at 22:30.
4
Press the OFF TIMER button.
The display changes from blinking to steady lighting and the setting is complete.
The timer light (yellow) is on.
NOTE
Changing of set time
Set a new time by using the OFF TIMER button.
How to cancel
Press the CANCEL button to turn off the timer display.
• The unit stops at the end of the set period of time.
• Make sure to press the button within 60 seconds from the last operation in step 3,
otherwise the setting is not completed.
• The current time is not displayed during OFF-TIMER operation.
• OFF-TIMER operation will not function during ALLERGEN CLEAR operation.
• Different from SLEEP TIMER operation, automatic set temperature adjustment is
not done during OFF-TIMER operation.
– 11 –
RLA012A013_EN_001-022
11
08/04/2009, 10:45
ON-TIMER operation
■ Operation starts 5 to 60 minutes before the set time so that the room temperature reaches the optimum temperature at the set time.
ON-TIMER operation can be set regardless of whether the air-conditioner is running or not.
Page 13
Example: In the case the preferred room temperature is required at 8:00.
1
2
Press the ON-TIMER button.
ON TIMER indicator
is blinking.
Press the “
or
” button.
Every time the
button is pressed, the display is switched in the order of:
0:00
0:10
Every time the
0:00 23:50
0:20
...
1:00
1:10
(Units of ten minutes)
button is pressed, the display is switched in the order of:
23:40
... 23:00
22:50
(Units of ten minutes)
Set at 8:00.
3
Press the ON TIMER button.
The display changes from blinking to steady lighting and the setting is complete.
The timer light (yellow) is on.
The operation stops if it is set during operation.
NOTE
Changing of set time
Set a new time by using the ON-TIMER button.
How to cancel
Press the CANCEL button to turn off the timer
indicator.
• Operation starts 5 to 60 minutes before the set time.
• The timer light (yellow) goes out at the set time.
• Make sure to press the button within 60 seconds from the last operation in step 2, otherwise the setting is not completed.
• The current time is not displayed during ON-TIMER operation.
• ON-TIMER operation will not function during ALLERGEN CLEAR operation.
SLEEP TIMER + ON-TIMER operation
■ Combined timer operation of SLEEP TIMER and ON TIMER.
Example: When it is required to stop after 3 hours and then start operation at 8:00, near
the set temperature.
■ SLEEP TIMER setting
Set by the procedures on page 11.
Set to
■ ON TIMER operation setting
Set by the above procedure mentioned in ON TIMER.
Set to
The setting of the lighting of the timer light (yellow) of this unit is complete.
h
• After the SLEEP TIMER set time has elapsed, the operation stops, and it starts
from 5 to 60 minutes before the ON TIMER’s set time.
• The timer light is turned off when ON TIMER set time comes.
Changing of set time
How to cancel
Set a new time by using the SLEEP or ON TIMER button.
Press the CANCEL button to turn off the timer display.
– 12 –
RLA012A013_EN_001-022
12
08/04/2009, 10:45
PROGRAM TIMER operation
■ The timer operations of the combination of ON and OFF TIMER. Once this has been set the timer operations will be repeated at the same time every
day unless the ON/OFF button is pressed.
Example: When it is prefered to stop at 22:30, and then start operation at 8:00, near the
set temperature.
■ OFF TIMER operation setting
Set by the procedures on page 11.
Set to
■ ON TIMER operation setting
Set by the procedures on page 12.
Set to
Timer light (yellow) on the unit will light when the setting is completed.
The set time will be displayed on the remote control unit. The display will
change depending on the operational status.
With ON TIMER, the air conditioner starts running. Then,
with OFF TIMER, the air conditioner stops running.
With OFF TIMER, the air conditioner stops running. Then,
with ON TIMER, the air conditioner starts running.
Changing of set time
Set a new time by using the OFF TIMER or ON TIMER button.
How to cancel
Press the CANCEL button to turn off the timer display.
In ON TIMER operation, the unit starts the operation a little earlier, so that the
room can approach optimum temperature at ON time. This is so called
“Comfort start-up”.
• Mechanism
The room temperature is checked
In COOL operation
60 minutes before the ON time.
(Stop) Operation starts
Depending on the temperature at
that time, the operation starts 5 to
60 minutes before the timer is at
(Operation)
ON.
• The function is available for both Set temperature
COOL and HEAT operation
mode (including AUTO). It does
Set time
Check the room
not work for DRY mode.
temp. 60 mins.
before.
When SLEEP TIMER is selected, the set temperature is automatically
adjusted after a while, ensuring that the room is not too cold during cooling or
too warm during heating.
• During cooling : the preset temperature is lowered by 1°C at the start of
SLEEP operation (when the timer is set). After that, the temperature goes
up by 1°C every an hour to become 1°C higher than the present
temperature.
▼
SLEEP TIMER
▼
Comfort Start-up
• During heating: Preset temperature is lowered by 1°C at the start of SLEEP
operation (when the timer is set). After that the temperature to becomes
3°C lower in an hour and 6°C lower in two hours than the present
temperature.
ALLERGEN CLEAR operation
■ The power of enzymes is used to eliminate allergy-causing allergens that accumulate on
the allergen clear filter.
Aim the remote control at the air-conditioner.
1
Press the ALLERGEN CLEAR button.
To stop:
Press the ON/OFF or
ALLERGEN CLEAR button.
NOTE
• Since the room temperature may change quite a bit, it is recommended that this
be used when no one is in the room. (It completes automatically in approximately 90 min.)
• During ALLERGEN CLEAR operation temperature, fan speed, airflow direction and timer operations settings cannot be made.
– 13 –
RLA012A013_EN_001-022
13
08/04/2009, 10:45
HIGH POWER/ECONOMY operation
If the air-conditioner is not operating, point the remote control toward the air conditioner, and
1
2
Press the ON/OFF button.
Press the HI POWER/ECONO button.
• When the operating mode is AUTO, COOL or HEAT
Every time the HI POWER/ECONO button is pressed, the display is switched in
the order of:
No display
(HIGH POWER)
(ECONOMY)
(Normal operation)
• When the operating mode is DRY or PROGRAM TIMER
Every time the HI POWER/ECONO button is pressed, the display is switched in
the order of:
No display
(Normal operation)
(ECONOMY)
Concerning HIGH POWER operation
Pressing the HI POWER/ECONO button intensifies the operating power and initiates powerful cooling or heating operation for 15 minutes
continuously. The remote control
displays and the FAN SPEED display disappears.
NOTE
• During the HIGH POWER operation, the room temperature is not
controlled. When it causes an excessive cooling or heating,press
the HI POWER/ECONO button again to cancel the HIGH
POWER operation.
• HIGH POWER operation is not available during the DRY, the
program timer and 3D AUTO operations.
• When HIGH POWER operation is set after ON TIMER operation,
HIGH POWER operation will start from the set time.
• When the following operations are set, HIGH POWER operation
will be canceled.
1 When the HI POWER/ECONO button is pressed again.
2 When the operation mode is changed.
3 When it has been 15 min. since HIGH POWER operation
has started.
4 When the 3D AUTO button is pressed.
• Not operable while the air conditioner is OFF.
Concerning ECONOMY operation
Pressing the HI POWER/ECONO button initiates a soft operation with the power suppressed in order to avoid an excessive cooling or heating.
The unit operates 1.5°C higher than the setting temperature during cooling or 2.5°C lower than that during heating. The remote control
displays and the FAN SPEED display disappears.
NOTE
• It will go into ECONOMY operation at the next time the air-conditioner runs in the following case.
1 When the air-conditioner is stopped by ON/OFF button during
ECONOMY operation.
2 When the air-conditioner is stopped in SLEEP or OFF
TIMER operation during ECONOMY operation.
3 When the operation is retrieved from CLEAN or
ALLERGEN CLEAR operation.
• When the following operations are set, ECONOMY operation will
be canceled.
1 When the HI POWER/ECONO button is pressed again.
2 When the operation mode is changed DRY to FAN.
• Not operable while the air conditioner is OFF.
– 14 –
RLA012A013_EN_001-022
14
08/04/2009, 10:45
SELF CLEAN operation
■ CLEAN operation should be run after AUTO, COOL and DRY operation to remove the moisture from inside the indoor unit and control the growth
of mold and bacteria.
1
In order to active CLEAN operation, press the CLEAN switch
with the tip of a ballpoint pen.
Every time the CLEAN switch is pressed, the display is switched
in the order of:
No display
(CLEAN off)
(CLEAN on)
NOTE
• Two hours later, the air conditioner stops running automatically. To stop the air
conditioner immediately, press the ON/OFF button.
• CLEAN operation is not operated after HEAT and FAN, OFF-TIMER, SLEEP
and ALLERGEN CLEAR operations have finished.
• The indoor unit fan runs for about two hours in CLEAN operation.
• The RUN light illuminates during CLEAN operation.
3 sec.
ON
OFF
1 sec.
• Pressing the SLEEP button or ALLERGEN CLEAR button during CLEAN operation cancels the CLEAN operation and then the unit is set to SLEEP or
ALLERGEN CLEAR operation.
• This is not a function for removing mold, germs or grime that have already adhered to the unit.
Auto restart function
■ What is auto restart function?
• Auto restart function records the operational status of the air-conditioner immediately prior to be switched off by a power cut, and then automatically
resumes operations after the power has been restored.
• The following settings will be cancelled:
1 Timer settings
2 HIGH POWER operations
NOTE
• Auto restart function is set at on when the air-conditioner is shipped from the factory. Consult with your dealer if this function needs to be
switched off.
• When power failure occurs, the timer setting is cancelled. Once power is resumed, set the timer again.
Tips for effective operation
■ Please observe the following for the most economic and comfortable use of your unit.
Set a suitable room temperature.
Clean the filters frequently.
Avoid direct sunlight and draught.
Excessively high or low temperatures are not
good for your health and waste of electricity.
Clogged filters may block the airflow and
cause less efficient operation.
Cut out direct sunlight by drawing the curtains or blinds when cooling. Keep windows
and doors shut, except when ventilating.
Adjust the airflow direction properly.
Operate the unit only when needed.
Keep heat source away when cooling.
Adjust the up/down and left/right airflow to
ensure a steady room temperature.
Use the timer properly to operate the unit
only when needed.
Keep heat sources out of the room as much as
possible.
– 15 –
RLA012A013_EN_001-022
15
08/04/2009, 10:45
– 16 –
RLA012A013_EN_001-022
16
08/04/2009, 10:45
Maintenance
Before maintenance
Turn off the power supply.
• Do not spill any liquid.
There's a danger
of electric shock.
During the operational season
Cleaning the air filter
Standard interval is once every two week
• Pull up the air inlet panel forward.
• Lightly hold the knobs at both sides and lift a
little to remove the panel forward.
1
Remove the air filter
2
Cleaning If the filter is very dirty, clean it with warm water (approx. 30°C),
and dry it thoroughly.
CAUTION
• Do not clean the filters with boiling water.
• Do not dry them over an open flame.
• Pull them out gently.
3
Wipe the unit with a soft,
dry cloth.
• Do not touch the aluminum fins on the heat
exchanger.
• Stand firmly on a stepladder or other stable
object when removing the inlet panel and filter.
Do not use the following articles:
• Hot water (40°C or more)
It may deform or discolour the unit.
• Petrol, paint thinner, benzine or cleanser, etc.
They may deform or scratch the unit.
Reinstall the air filter
• Hold firmly the filter at both sides as shown at right
and insert securely.
• Operating without putting back the air filters will
make the unit dusty, and may cause damage.
Cleaning the unit
• Wipe the unit with a soft, dry cloth, or use a vacuum cleaner.
• If the unit is very dirty, wipe it with a cloth soaked in warm water.
Cleaning the air inlet panel
• Removal, installation of air inlet panel.
• The panel can be washed with water. After washing
with water, wipe any moisture off the panel and dry
out of direct sunlight.
How to open, close the air inlet panel
Open
Place fingers at the recesses on both sides of the panel and pull up the panel
forward so that it will be open by about 60 degrees.
Close
Push both ends evenly and press further lightly at the center.
Removal, installation of air inlet panel
Removal
When removing the air inlet panel for internal cleaning or others, open the
panel by 80 degrees and then pull it forward.
Installation
Secure the upper edge of the air inlet panel by lightly pushing it in, and then
close the panel.
– 17 –
RLA012A013_EN_001-022
17
08/04/2009, 10:46
Cooling/heating is affected by an air filter clogged up with dust etc., and the operation noise becomes louder. It may also
use extra electricity. Please clean the air filter at appropriate intervals.
NOTE
At the end of the season
1
Perform the fan operation for a half day.
2
Stop the unit and turn off the power supply.
3
4
5
Clean and reinstall the air filters.
At the beginning of the season
Dry the inside of the unit.
The unit consumes appr. 2W even when the unit is not operating.
Turning off the power supply will help saving energy consumption and cost.
Clean both the indoor and outdoor units.
Remove batteries from the remote control.
1
Make sure that there are no obstacles blocking the
airflow around the air intake and outlet openings of
the indoor and outdoor units.
2
3
4
5
6
Check if there is no corrosion or rust on the base
frame of the outdoor unit.
Ensure that the earth wiring is not snapped nor
disconnected.
Ensure that the air filters are clean.
Turn on the power supply.
Insert batteries in the remote control.
Installing, inspecting, and replacing the air-cleaning filter
1. Open the air inlet panel and remove the air filters.
Page 17
2. Remove the filter holders, with the air-cleaning filter installed in the folders, from the airconditioner.
3. Remove the allergen clear filter (Light orange) from filter holder and inspect the filter. Use
a vacuum cleaner to remove any dust or dirt from the allergen clear filter. Replace the
allergen clear filter if it cannot be cleaned or if it has been for about 1 year.
(The allergen clear filter should be replaced after about 1 year of use. However, the actual
replacement period may vary depending on the conditions in which the filter is used.)
Remove the photocatalytic washable deodorizing filter (orange) from the filter holder and
inspect the filter. Periodically, remove any dust or dirt from the photocatalytic washable
deodorizing filter. If the photocatalytic washable deodorizing filter is particularly dirt, it
may be washed with water. However, the filter is fragile so be sure to wash it installed in the
filter holder to avoid damaging it. After washing the filter, place it in sunlight to dry. Placing the filter in sunlight revitalizes the deodorizing effect.
Filter holder
(Do not dispose of the filter holders. They are reusable. )
4. Install the air-cleaning filter in the filter holders, and then install the filter
holders in the air-conditioner.
NOTE
Filter
• The allergen clear filter and the photocatalytic washable deodorizing filter
may be installed on either the right or left side of the air-conditioner.
• Install the allergen clear filter with the light orange side front.
5. Install the air filters and closed the air inlet panel.
Page 17
CAUTION
• The heat exchanger may injure your fingers.
For replacement the air-cleaning filter, contact your dealer.
Item
Feature
The power of enzyme is used to eliminate allergy-causing allergens that accumulate on the filter.
Allergen clear filter
Photocatalytic washable Sources of odors on the filter are broken up, resulting in a
deodorizing filter
deodorizing effect.
Color
Light orange
Orange
– 18 –
RLA012A013_EN_001-022
18
08/04/2009, 10:46
Proper installation
Suitable installation position
• Do not put any obstruction in front of the indoor unit, preventing proper ventilation and functioning.
• Do not install the unit in any of the following places:
• Where there is a danger of leaking flammable gases.
• Where there is substantial splashing of oil.
• Malfunctioning due to corrosion may occur if the unit is installed in a spa where sulfide gases are generated, or in a seaside resort exposed to
sea breezes. Contact your dealer.
• The air-conditioner and remote control must be at least 1 metre away from a TV set or radio.
• Drain the dehumidified liquid from the indoor unit into a spot that drains well.
Pay attention to operating noises!
•
•
•
•
When you install the unit, take care to choose a place that can comfortably stand the weight of the unit and does not increase the operating noise
or vibration. If vibration is transmitted through the house, fix the unit with the aid of vibration-proof pads between the unit and the fittings.
Select a place where cold or hot air, operation noises from the indoor and outdoor units do not cause any inconvenience to your neighbours.
Do not leave any obstacles near the outlet and inlet of the outdoor unit. This may cause malfunctioning and increased operating noise.
If you hear an irregular noise during operation, contact your dealer.
Inspection and maintenance
Depending on operating environment, the inside of the air-conditioner may become dirty after a few year operations. This will reduce
performance. In addition to normal cleaning, we would recommend inspection and maintenance. (This may lead the air-conditioner to having a
longer life without any trouble.)
• Contact your dealer, or any distributor, for inspection and maintenance. (There will be a charge for this service).
• We would recommend inspection and maintenance to be carried out during the off-season.
• If the supply cord of this appliance is damaged, it must only be replaced by a repair shop appointed by the manufacturer, because special
purpose tools are required.
Troubleshooting
Please carry out the following checks before making a service call.
The air-conditioner does not work at all.
Has the power switch been
turned off?
Has the timer been set in the
“ON” position?
Is there a power failure or a
blown fuse?
If the air-conditioner does not operate properly after you have checked
the left points, or if any doubt still
exists after you have consulted page
20, or if things happen as shown on
page 21, switch off the power and
contact your dealer.
Poor cooling or heating
Have you set the thermostat at a
suitable temperature?
Is the air filter clean? (Not
clogged?)
Did you leave any doors or
windows open?
suitable
temperature
Poor cooling
Is there any direct sunlight entering the room?
Is there a heat source in the
room?
Are there too many people in
the room?
An alternative refrigerant (R410A) is used in this air-conditioner. When asking your
dealer for service or inspection and maintenance, explain the dealer about it.
– 19 –
RLA012A013_EN_001-022
19
08/04/2009, 10:46
Notice
The unit does not restart immediately after you have
stopped it.
Restart is blocked for 3 minutes after you have stopped the operation
to protect the unit.
(RUN light is on)
Not
operating?
Please wait for
three minutes.
The three-minute protection timer in the microcomputer automatically
starts it up again.
Airflow is not blown out when starting the HEATING
operation.
Airflow has stopped to prevent blowing out of cold air until the indoor
heat exchanger has warmed up. (2 to 5 min.) (HOT KEEP program)
RUN light blinks slowly
(1.5 sec ON, 0.5 sec OFF)
Airflow is not blown out for 5 to 10 min. or blown out not
warm wind for a moment at HEATING operation.
RUN light blinks slowly
(1.5 sec ON, 0.5 sec OFF)
Airflow is not blown out when starting the DRY operation.
When outdoor temperature is low and humidity is high, the unit sometimes performs defrosting automatically. Please wait. During defrosting, water or steam may escape from the outdoor unit.
The indoor fan may stop to prevent re-evaporation of dehumified
moisture and to save energy.
(RUN light is on)
Some steam escapes during COOL operation.
This may occur if the room's temperature and humidity are very high.
It disappears as soon as the temperature and humidity decrease.
There is a slight smell.
Air blown out during operation may smell. This is caused by tobacco
or cosmetics adhering to the unit.
You hear a slight gurgling sound.
This is caused by refrigerating liquid moving within the unit.
You hear a slight cracking sound.
This is caused by heat expansion or contraction.
You hear a hissing or clicking sound.
This is caused by the operation of the refrigerant control valves or
electric components.
After a power cut, the unit does not restart even if power has been
restored.
If the auto restart function is not set, the unit will not restart
automatically. Use the remote control to start the operation again.
Remote control signals are not received.
Remote control signals may not be received if the signal receiver on
the air-conditioner is exposed to direct sunlight or other bright light.
If so, cut out the sunlight or reduce the other light.
Moisture may form on the air outlet grills.
If the unit is operated for a long time in high humidity, moisture may
form on the air outlet grills and start dripping.
Whistling noise is heard from the outdoor unit.
The noise means that the revolution speed of the compressor is
increasing or decreasing.
Fan won't stop immediately after unit operation was
stopped.
Indoor fan : Fan will not stop after 2 hours if set to CLEAN operation.
Outdoor fan : Fan will not stop about a 1 minute period in order to
protect the unit.
RUN light stays on even though operation was stopped.
The RUN light illuminates during CLEAN operation.
Run light turns off when CLEAN operation ends.
Sometimes a “Shooooo” sound might come for a short time
from the unit that is turned off.
This is the sound when operation of another indoor unit is stopped.
– 20 –
RLA012A013_EN_001-022
20
08/04/2009, 10:46
Contact your dealer
■ Turn off the power switch immediately and inform your dealer in any of the following situations:
The fuse or switch blows continuously.
The cable becomes extremely hot.
The covering of the cable is cracked.
CAUTION
Fuse often blows.
The TV, radio or other equipment
starts to malfunction.
If the power cord becomes damaged, ask your dealer or a qualified engineer to install the
replacement to avoid accidents.
A switch does not activate properly.
When abnormalities occur, turn off the power supply
immediately and turn it on after 3 minutes. Restart the
operation with ON/OFF button of the remote control and the
abnormalities still continue.
You hear a strange noise during operation.
The RUN and TIMER lights on the unit display section blink
quickly (0.5 sec. ON; 0.5 sec. OFF) and do not work.
About the Multiple Air-conditioner
Simultaneous Operation
• The air-conditioners cannot be in different operating modes at the same time, such as one unit being in the “Cool” mode and one unit being in
the “Heat” mode.
• When conducting different operations, the air-conditioner that was operated first will be given priority, so the air-conditioner that is operated
after that will conduct air blowing operation.
• When you want to give priority to the air-conditioner that was started later, either stop the air-conditioner that has priority or cause the
operation type of the unit operated first to match that of the unit operated second.
Automatic Operation
• When the remote control operation switch is in the “Auto” mode the air-conditioner automatically selects either “Cool,” “Dry,” or “Heat” when
operation is started depending on the room temperature.
• During simultaneous operation of air-conditioner units, operation modes may be automatically changed in response to the temperatures of the
individual rooms; this will result in the operation of the outdoor unit being stopped. In such a case, COOL or HEAT mode should be used
instead of AUTO. (This is only relevant when more than one air-conditioner unit is being used.)
Refrigerant (oil) recovery operation
• If the all of the indoor units are not operated at the same time for an extended period, the cooling or heating performance may temporarily
decrease. This is in order to control the recovery of the refrigerant (oil) in the stopped indoor unit(s). At this time, the sound of refrigerant
flowing may be heard from the stopped indoor unit(s).
– 21 –
RLA012A013_EN_001-022
21
08/04/2009, 10:46
Self diagnosis function
■ We are constantly trying to do better service to our customers by installing such judges that show abnormality of each function as follows:
RUN light
Description of trouble
Cause
1 time flash
Heat exchanger sensor 1 error
• Broken heat exchanger sensor 1 wire, poor connector
connection
2 time flash
Room temperature sensor error
• Broken room temperature sensor wire, poor connector connection
3 time flash
Heat exchanger sensor 3 error
• Broken heat exchanger sensor 3 wire, poor connector
connection
5 time flash
Active filter voltage error
• Defective power supply
6 time flash
Indoor fan motor error
• Defective fan motor, poor connector connection
7 time flash
Refrigerant is insufficient
Closed service valve
Heat exchanger sensor 1 error
• Refrigerant is insufficient, leaking
• Closed serice valve
• Broken heat exchanger sensor 1 wire, poor connector connection
1 time flash
Outdoor temperature sensor error
• Broken outdoor sensor wire, poor connector connection
2 time flash
Outdoor heat exchanger fluid pipe
sensor error
• Broken heat exchanger fluid pipe sensor wire, poor connector
connection
4 time flash
Discharge pipe sensor error
• Broken discharge pipe sensor wire, poor connector connection.
5 time flash
Suction pipe sensor error
• Broken suction pipe sensor wire, poor connector connection
1 time flash
Current cut
• Compressor locking, open phase on compressor output,
shortcircuit on power transistor, closed service valve
2 time flash
Trouble of outdoor unit
• Broken power transistor, broken compressor wire
• Broken discharge pipe sensor wire, poor connector connection
• Compressor blockage
3 time flash
Over current
• Overload operation, overcharge
4 time flash
Power transistor error
• Broken power transistor
5 time flash
Over heat of compressor
• Gas shortage, defective discharge pipe sensor, closed service
valve
6 time flash
Error of signal transmission
• Defective power supply, Broken signal wire, defective in/outdoor
unit boards
7 time flash
Outdoor fan motor error
• Defective fan motor, poor connector connection
Cooling high pressure protection
• Gas over charge, short circuit of outdoor unit
Rotor lock
• Defective compressor
• Open phase on compressor
• Defective outdoor unit boards
TIMER light ON
TIMER light
RUN light keeps flashing
RUN light ON
Keep flashing
2 time flash
RUN light 2 time flash
– 22 –
RLA012A013_EN_001-022
22
08/04/2009, 10:46
USER’S MANUAL
AIR-CONDITIONER
ENGLISH
MANUEL DE L’UTILISATEUR
FRANÇAIS
CLIMATISEUR
ANWENDERHANDBUCH
DEUTSCH
¨T
KLIMAGERA
ISTRUZIONI PER L’USO
SRK20ZJ-S
SRK25ZJ-S
SRK35ZJ-S
SRK50ZJ-S
ITALIANO
CONDIZIONATORE D’ARIA
MANUAL DEL PROPIETARIO
ESPAN˜OL
ACONDICIONADOR DE AIRE
GEBRUIKERSHANDLEIDING
NEDERLANDS
AIRCONDITIONING
MANUAL DO UTILIZADOR
PORTUGUÊS
APARELHO DE AR CONDICIONADO
ΟΔΗΓΙΕΣ ΧΡΗΣΗΣ ΕΛΛΗΝΙΚΑ
ΚΛΙΜΑΤΙΣΤΙΚΟ
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
РУССКИЙ
КОНДИЦИОНЕР ВОЗДУХА
KULLANIM KILAVUZU
AIR-CONDITIONING & REFRIGERATION SYSTEMS HEADQUARTERS
16-5, 2-Chome, Kounan, Minato-ku, Tokyo, 108-8215, Japan
Fax: (03) 6716-5926
MITSUBISHI HEAVY INDUSTRIES EUROPE, LTD.
AIR-CONDITIONER DIVISION
3rd Floor Thavies Inn House 3-4 Holborn Circus London EC1N 2HA, ENGLAND
Phone: 44(0)20 7842 8171
Fax: 44(0)20 7842 8104
RKY012A006_Cover_2009-0611
1
This air conditioner complies with EMC Directive 2004/108/EC,
LV Directive 2006/95/EC.
Este acondicionador de aire cumple con la directiva EMC: 2004/
108/EC, LV Directiva 2006/95/EC.
Ce climatiseur est conforme à la Directive EMC: 2004/108/EC, LV
Directive 2006/95/EC.
Deze airconditioner voldoet aan EMC Directive 2004/108/EC, LV
Directive 2006/95/EC.
Dieses Kimagerät erfüllt die EMC Direktiven 2004/108/EC, LV
Direktiven 2006/95/EC.
Este aparelho de ar condicionado está em conformidade com a
Directiva EMC 2004/108/EC e a Directiva LV 2006/95/EC.
Questo condizionatore d’aria è conforme alla Direttiva EMC: 2004/
108/EC, LV Direttiva 2006/95/EC.
∞˘Ùfi ÙÔ ÎÏÈÌ·ÙÈÛÙÈÎfi Â›Ó·È Û‡ÌʈÓÔ Ì ÙȘ ÚԉȷÁڷʤ˜ Ù˘
√‰ËÁ›·˜ EMC 2004/108/EK Î·È Ù˘ √‰ËÁ›·˜ LV 2006/95/EK.
TÜRKÇE
RLA012A013
07/14/2009, 14:10
Download PDF