Proxima | PL-300E | User`s guide | Proxima PL-300E User`s guide

Liquid Crystal Projector
Model
DP5800
USER’S GUIDE
Please read this user’s guide for fast setup and use of your new projector. After reading this guide,
keep it in a safe place for future reference.
DP5800 Features
High brightness
Highly efficient optical system with a metal halide lamp
ensures high brightness.
High resolution
Three separate high-definition liquid crystal panels are
used to provide sharp, clear pictures.
Compact size and light weight for
portability
RGB output terminal
RS232C communication
Mouse emulation
Power zoom and power focus
Contents
Page
Symbols Used in this Guide ... 3
Safety Precautions ................. 4
Your DP5800 Projector ........... 6
Installation .............................. 8
Using the Projector ................. 9
Projector Messages and
Indicators .................... 11
Using the Menus .................. 12
Connecting to a Video
Source ......................... 17
Connecting to an
RGB Signal ................. 17
Connecting to a Control
Signal .......................... 20
System Setup ....................... 25
Cleaning the Air Filter ........... 26
Lamp Replacement .............. 26
Troubleshooting .................... 27
Specifications ...................... 28
Warranty and Servicing
..................... Back cover
For Customers in the United Kingdom
THIS PRODUCT IS SUPPLIED WITH A TWO-PIN MAINS PLUG FOR USE IN MAINLAND EUROPE.
FOR USE IN THE U.K., PLEASE REFER TO THE NOTES ON THIS PAGE.
IMPORTANT FOR THE UNITED KINGDOM
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is
indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS 1362
fuse must be used of the same rating. If the fuse cover is detachable, never use the plug with the cover omitted.
If a replacement fuse cover is required, ensure it is of the same colour as that visibe on the pin face of the plug.
Fuse covers are available from your dealer.
DO NOT cut off the mains plug from this equipment. if the plug fitted is not suitable for the power points in
your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension
lead or consult your dealer.
Should it be necessary to change the mains plugs, this must be carried out by a competent person, preferably a
qualified electrician.
If there is no alternative to cutting off the mains plug, ensure that you dispose of it immediately, having first
removed the fuse, to avoid a possible shock hazard by inadvertent connection to the mains supply.
WARNING: THIS EQUIPMENT MUST BE EARTH GROUNDED
Important:
The wires in the mains lead are coloured in accordance with the following code:
Green and Yellow = Earth
Blue = Neutral
Brown = Live
Green & Yellow to Earth
Brown to Live
Fuse
Blue to Neutral
Cord Clamp
As these colours may notorrespond with the colured markings identifying the terminals in your plug,
proceed as follows:
1. The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol or coloured Green or Green and Yellow.
2. The wire coloured Blue must be connected to the terminal marked with the letter N or coloured
BLUE or BLACK.
3. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured
BROWN or RED.
2
WARNING: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Instructions to Users:
This equipment complies with the requirements of FCC (Federal Communication Commission) Class A
equipments provided the following conditions are met.
(1) Video signal cables:
Double shielded coaxial cables (so called FCC shield cable) must be used and the outer shield must be
connected to the ground. Or, if normal coaxial cables are used, the cables must be enclosed in metal pipes
or in a similar way to reduce interference noise radiation.
(2) Power cord:
Shielded power cord must be used. The outer shield must be connected to the ground.
(3) Video inputs:
The input signal amplitude must not exceed the specified level.
Symbols Used in This Guide
Various symbols are used in this guide to help you use the product correctly and safely, and also to protect you
and others from danger and your property from being damaged.
Warning
This symbol indicates conditions that could result in serious injury or death
if ignored.
Caution
This symbol indicates conditions that could result in injury or damage to the
equipment if ignored.
Examples of
illustrated
marks
The
mark indicates a Warning (or Caution).
The details of the warning (the left diagram shows the caution for an electric
shock hazard) are shown in the diagram.
The mark indicates a prohibited action. The details of the prohibited action
(the left diagram shows a warning not to disassemble the unit) are shown in the
diagram or near it.
The mark informs you of actions you must do. The details (the left diagram
shows “Disconnect the power plug from the power outlet”) are drawn in the
diagram.
3
Safety Precautions
Warnings
If any unusual performance occurs.
•
•
•
An abnormal smell or smoke may indicate the possibility
of fire or electric shock, etc. When any unusual
performance is observed, immediately turn off the power
switch and pull out the power plug from the power outlet.
Check that there is no smoke, etc., and then contact your
dealer to repair the unit. Do not repair it yourself .
Do not use this unit as it is after
trouble has occurred, such as “No
picture”,“No sound”, “Abnormal
sound”, etc. This may cause a fire,
electric shock, etc. In this case
immediately turn off the power
Pull out the
power plug
switch and disconnect the power
from the
plug, then contact your dealer to
power outlet.
repair the unit.
If water, etc. enters inside the unit, turn off the power
switch of the unit first and then disconnect the power plug
and contact your dealer. If you use it as it is, it may cause
fire, electric shock, etc.
Do not install this unit in an
unstable place.
placing the projector in an unstable
• Avoid
place such as weak base, inclined floor, etc.
Pull out the
power plug
from the
power outlet.
Do not modify this unit.
Do not modify this unit. It may cause a fire,
electric shock, etc.
Prohibition
of disassembly
Do not put a container, etc. with liquid
on this unit.
Do not put a vase, flowerpot, cosmetic
container, medicine or water or small metal
objects on this unit. If liquid spills and enter
inside the unit, it may cause a fire, electric
shock, etc.
Do not use this unit with a power voltage other
than those specified. It may cause a fire,
electric shock, etc.
Do not open the cabinet.
Be careful in handling the power cord.
Electric
shock
hazard
Prohibition
of disassembly
Do not use the projector near water.
Do not use this unit in a kitchen,
bathroom, etc. This may cause a
fire, electric shock, etc.
Do not use
near water
Do not look directly at the lens when
the lamp is lit.
Since a strong light is used, it could damage your
vision, etc. Pay special attention if children are
present.
not insert a metal or flammable object
• Do
inside the ventilation holes or other openings.
This may cause a fire, electric shock, etc.
foreign matter enters the case, turn the
• Ifpower
switch off and disconnect the power
plug from the power outlet and contact your
dealer. If you use as it is, it may cause a fire,
electric shock, etc. Be especially careful if
children could touch the unit.
not scratch or damage or bend the power cord. Do not
• Do
put a heavy object on it, heat it or pull it. If you do, the
•
power cord may be damaged and it may cause a fire,
electric shock, etc.
Do not rest the projector on the power cord. The power
cord may be damaged and it may cause a fire, electric
shock, etc, be sure that heavy objects are not put on it.
the cord is damaged (core wire is exposed,
• Ifdisconnected,
etc.), ask your dealer to replace
it. It may cause a fire, electric shock, etc.
that no dirt adheres to the power plug and fully
• Check
insert it without any play. If dirt adheres or the connection
is incomplete, it may cause a fire, electric shock, etc.
Do not insert any foreign object.
4
If you drop this unit or if the cabinet is broken,
turn off the power switch, disconnect the
power plug and contact your dealer. If you use
it as it is, it may cause a fire, electric
shock, etc.
Do not use power supplies other
than those specified.
This may cause it to drop or fall over, resulting
in injury.
There are high voltage parts inside
the cabinet which may cause electric
shock. Ask your dealer to check
inside and adjust and repair the unit.
Do not apply any shock.
Pull out the
power plug
from the
power outlet.
Cautions
Do not step on this unit or place a
heavy object on it.
• When inserting batteries in this unit, pay
attention to the direction of the
and
polarity indications and insert the batteries
correctly. If the polarities are confused, it
may cause injury or damage near the unit
due to burst batteries, liquid leakage, etc.
not step on this unit. Pay special attention
• Do
if children are present. If you do, the unit may
fall over or may be broken causing an injury.
not put a heavy object on this unit. If you do, the unit
• Do
may fall due to its imbalance or it may drop, causing an
injury.
Do not block the ventilation holes.
If the ventilation holes are blocked, heat may
build up inside and it may cause a fire. Do not
use this unit on its side, in a poorly ventilated,
narrow place, on a carpet or bedspread or covered
with a cloth. Place this unit so that the ventilation holes
are kept 10cm or more away from the wall.
Cleaning
Be sure to pull out the power plug
from the power outlet for safety
when cleaning.
Pull out the
power plug
from the
power outlet.
Do not place this unit in a moist or
dusty place.
not place this unit in a moist or dusty place. It may
• Do
cause a fire, electric shock, etc.
not place this unit where it would be
• Do
exposed to soot or steam, near a cooking stove
or humidifier, etc. It may cause a fire, electric
shock, etc.
Set the caster stoppers.
When this unit is installed on a table with casters,
set the caster stoppers. If the table moves, it may
fall over, causing an injury.
Handle the power cord carefully.
not bring the power cord near a heating device. The
• Do
shield of the cord may melt and it may cause a fire, electric
shock, etc.
not insert/disconnect the power plug with
• Do
wet hands. It may cause an electric shock.
the power plug is to be
• When
disconnected, do not pull on the power
cord itself. The power cord may be
damaged and it may cause a fire, electric
shock, etc. Pull on the power plug.
Use of batteries.
not use batteries not specified for this unit.
• Do
Do not use new batteries mixed together with
Long term without use.
When you are not going use this
unit for a long time be sure to pull
the power plug from the power
outlet and cover the lens.
Pull out the
power plug
from the
power outlet.
Clean inside the unit every 24 months.
Ask your dealer to clean inside the unit at least
once every two years. If the unit is left with
too much dust inside, it may cause a fire.
Caution when carrying it.
Cover the lens and be sure to
disconnect the power plug from
the power outlet and check that all
external connection cords are
removed before moving the
projector. If not, the cord may be
damaged and it may cause a fire,
electric shock, etc.
Pull out the
power plug
from the
power outlet.
Do not place this unit where it gets hot.
If you place the unit outdoors or in a place
exposed to direct sunlight or near a heating
device, the cabinet and parts could be affected.
Cleaning the lens.
To clean the lens, use a generally-available lens
cleaning tissue (used for cleaning cameras,
glasses, etc.). Be careful not to scratch the lens
with a hard object.
Cleaning the cabinet.
not use benzene, thinner, and other cleaning chemicals,
• Do
etc., as they may damage the plastic coating.
a chemically-treated cloth is used, follow the
• When
cautions that come with the cloth.
not leave a rubber or vinyl object touching the cabinet
• Do
for a long time. It may cause the cabinet to change in
•
quality or the coating to peel off.
Clean the dirt from the cabinet and operation panel by
dusting lightly with soft cloth, or wipe it with a cloth
moistened with detergent diluted with water. Then, wipe it
off with a dry soft cloth.
old ones. This may cause a fire or injury due
to burst of battery or liquid leakage.
5
Your DP5800 Projector
ON indicator
STANDBY / ON
button
Blinks in Standby mode.
Glows in operation mode.
(See page 11.)
Power ON/OFF button.
OFF sets the unit in
Standby mode.
LAMP indicator
Glows when the lamp
should be replaced.
(See page 11.)
TEMP Indicator
FOCUS button
Glows when temperature
inside the projector is too
high. (See page 11.)
temp
lamp
power
Adjusts focus.
ZOOM buttons
zoom
focus
Adjust picture size.
RESET button
Resets unit to factory
settings.
MUTE button
reset
mute
INPUT button
menu
MENU button
To select the input source.
Each time this button is pressed, the input source is
changed in sequence as shown below.
RGB1
RGB2
VIDEO1
VIDEO2
Input
Picture adjustments.
Refer to pages 12 − 16
for details.
Speaker
Remote control
sensor
Handle
Cooling fan
(exhaust)
Lens
Remote control
sensor
The remote control will function within
16 feet of the projector sensor and
within 30° to both the left and right.
Cooling fan
(intake)
RGB IN
S-VIDEO
VIDEO
L
AUDIO
R
RGB input terminal
VIDEO input terminal
(on video-equipped models only)
S-VIDEO input terminal
Mini DIN 4pin connector
VIDEO input terminal
RCA Jack
AUDIO L/R input terminal
RCA Jack
RGB input terminal
D-sub 15 pin
AUDIO
IN
AC SW
AUDIO
OUT
RGB OUT
RGB output
terminal
RGB output terminal
D-sub 15 pin
AC IN
MAIN POWER switch
CONTROL
Main power ON/OFF switch.
CONTROL terminal
D-sub 15 pin RS232
AC IN socket
Connect the provided
power cord.
AUDIO input
terminal
Stereo mini jack
AUDIO output
terminal
(RGB/VIDEO)
Stereo mini jack
6
Your DP5800 Projector (continued)
Remote control
MENU STICK SWITCH
Selects or adjusts the menu items in
Menu mode.
Works as the mouse in Play mode.
RESET / RIGHT button
STANDBY / ON button
Power ON/OFF button.
OFF sets the unit in Standby mode.
Resets menu items to factory settings
when menus are open.
Works as right mouse button in
Computer mode.
RIGHT
RIGHT
RISET
RESET
STANDBY/ON
MENU ON / OFF button
MENU
ZOOM button
Displays or removes the on-screen
menus.
Adjusts picture size.
ZOOM
FOCUS
TIMER ON / OFF button
Adjusts focus.
Displays or removes the TIMER menu.
When a Blank screen is displayed,
TIMER can not be set. (See page 15.)
VOL
TIMER
VOLUME button
BLANK
BLANK ON / OFF button
Displays a blank screen which can be
revealed by moving the MENU STICK
SWITCH. (See page 14.)
FOCUS button
POSITION
Adjusts volume.
MUTE
MUTE button
Turns the Audio off.
VIDEO1/2
RGB1/2
POSITION button
Move the picture with the MENU STICK
SWITCH while pressing the POSITION
button.
INPUT
INPUT SELECT button
Selects the input source.
How to insert batteries
1 . Remove the battery
compartment cover.
Slide the battery compartment
cover in the direction of the
arrow while pressing slightly
down on it.
Caution Cautions on use of batteries
• Do not use batteries not specified for this unit. Do not use
old and new batteries together. It may cause a fire, injury
due to burst of battery or liquid leakage.
• When inserting batteries, pay attention to the direction of
and
polarity indications and insert the batteries
the
correctly. If the polarities are not correct, it may cause
injury or damage near the unit due to a battery explosion
or liquid leakage.
2 . Insert the batteries as
illustrated inside the
battery compartment.
3 . Replace the cover.
Caution
Cautions on remote
control use
• Do not drop the remote control or apply any shock to it.
• Do not let the remote control get wet and do not put it on
a wet object.
• If you are not going to use the remote control for a long
time, remove the batteries from it.
• If operation of the remote control becomes difficult,
replace the batteries.
7
Installation
Projector and screen setup
Determine proper picture size and projection distance as illustrated below.
Top view
Side view
Screen
Lens center
b
a
Screen (inches)
a (inches)
b (inches)
Minimum Maximum
40
60
89
3.4
60
89
134
5.1
80
119
179
6.9
100
149
224
8.6
120
179
269
10.3
150
224
336
12.9
200
298
448
17.2
a: Distance from the projector to the screen
b: Length from the center of the lens to the bottom
of the picture
Using the foot adjusters
Adjust the projection position using the foot adjusters at the bottom of the projector.
Front view
Side view
In = unlock
Out = lock
Foot adjuster
Viewing angle can be changed from 1° ~ 7°.
1. Lift up the projector and unlock the foot adjusters.
2. Adjust the feet to the best viewing angle, and then lock the foot adjusters.
3. To adjust the angle slightly, rotate the foot adjusters.
Caution Do not unlock the foot adjusters unless you are supporting the projector, to avoid dropping the
projector and causing an injury.
Do not revolve the foot adjusters by force.
If the foot adjusters do not lock completely, move the foot slightly before locking.
8
Using the Projector
Projecting the picture
4
2 7 5
2
RIGHT
RISET
RESET
STANDBY/ON
MENU
4
ZOOM
5
FOCUS
VOL
TIMER
BLANK
1
7
POSITION
MUTE
VIDEO1/2
RGB1/2
3
INPUT
1
Turn the MAIN POWER switch of the projector on. [  : ON]
• The ON indicator will glow orange.
2
Press the STANDBY/ON button.
• The ON indicator blinks (green) and then glows (green).
3
Remove the lens cap.
4
Adjust the picture size using the ZOOM buttons.
5
Adjust the focus using the FOCUS buttons.
(1) Press the FOCUS button. The on-screen display shown on the right appears.
(2) Press the Focus +/- buttons until the picture is clear.
6
+++FOCUS+++
Turn on all connected equipment.
See pages 17-19 for the correct sequence for turning on various equipment.
7
Press the INPUT button or the INPUT SELECT (VIDEO or RGB)
button to select the source of the projected signal.
• The selected signal input source is displayed at the bottom right of the screen.
NOTE: Video 1/2 works with video capable units only.
RGB 1
9
Using the Projector (continued)
Turning off the power
1
1
RIGHT
RISET
RESET
STANDBY/ON
MENU
3
1
2
Press and hold the STANDBY/ON button for 1 second.
• The ON indicator lights up orange and the lamp turns off. About 1 minute later, the fan stops and the
indicator blinks orange.
NOTE: If you press the STANDBY/ON button for less than 1 second, the projector will not switch
to Standby mode.
2
Turn the MAIN POWER switch of the projector off. [
3
Replace the lens cap.
: OFF]
Caution Do not turn off the projector’s MAIN POWER switch before pressing the STANDBY/ON
button. After the STANDBY/ON button is pressed, the fan will run for about 1 minute to cool
the projector.
10
Projector Messages and Indicators
On screen display
The following messages may be displayed on the screen.
Message
Action
NO SIGNAL IS DETECTED
Check the input signal connection.
SYNC IS OUT OF RANGE
The horizontal frequency of the input signal exceeds the range of the
projector,and it cannot be displayed. Change the resolution of the input signal.
CHANGE THE LAMP
The lamp should be replaced.
Indicator display
The ON indicator, LAMP indicator and TEMP indicator will light or blink in the following cases.
Indicator status
ON indicator
Action
Meaning
Lights orange
Standby mode
—————————————
Blinks green
Warming up
—————————————
Lights green
Normal operation
—————————————
Blinks orange
Cooling down
—————————————
Lights red
Lamp cannot light
Cool projector by power off for 20 minutes.
Blinks red
Air filter detached
Check the air filter.
Lights red
Temperature inside too high
Check that ventilation holes are clear.
Blinks red
Cooling fan failure
Service the projector.
LAMP indicator
TEMP indicator
The LAMP indicator will light when the lamp becomes too hot.
1. Turn off the power and let the projector cool for 20 minutes.
2. Turn the projector back on. If the LAMP indicator still glows red, contact your dealer.
11
Using the Menus
2, 3
2
3
1
RIGHT
RIGHT
RISET
RESET
1
1
Press the MENU (
menu
STANDBY/ON
MENU
) button or the MENU ON / OFF button.
• Menus are displayed on the screen.
2
Select the menu to be adjusted using the MENU (
buttons or the MENU STICK SWITCH.
)
• The menu displayed in green is selected.
3
Select the item to be adjusted using the MENU (
buttons or MENU STICK SWITCH.
)
• The item displayed in green can be adjusted.
4
The changes take effect.
Storing your settings
Settings can be saved for the VIDEO1, VIDEO2, RGB1 and RGB2 input terminals. These adjustments are
saved after projector power is turned off.
To return to the initial settings
• Select the menu item to restore to the initial setting using the
menu buttons or menu stick switch.
• Press the RESET button.
• Select DEFAULT
• Select the item to restore to the initial setting.
• Press the RESET button a second time.
12
SETUP
VOL
BRI
CON
SHA
COL
TIN
INPUT
RESET
IMAGE
‘SETUP’
DEFAULT
CANCEL
OPT.
Using the Menus (continued)
SET UP Menu
The SET UP menu lets you change the picture characteristics and position. The menus will be different for RGB
and video signals.
RGB signal Setup mumu
SETUP
INPUT
IMAGE
VOLUME
BRIGHT
CONTRAST
V.POSIT
H.POSIT
H.PHASE
H.SIZE
VIDEO signal Setup menu (video models only)
OPT.
SETUP
INPUT
IMAGE
OPT.
VOLUME
BRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
121
57
7
800
Range
Item
VOLUME
Decrease
BRIGHT
(BRIGHTNESS)
Dark
CONTRAST
Lower
SHARPNESS*
Soft
Sharp
COLOR*
Less
More
TINT*
Red
Green
V.POSIT
(V.POSITION)
Moves the picture up or down.
H.POSIT
(H.POSITION)
Moves the picture left or right.
H.PHASE
Decreases the picture flicker.
H.SIZE
Widens or narrows the horizontal size of picture.
Increase
Bright
Higher
* Video models only
NOTE:
• TINT cannot be adjusted with PAL/SECAM video signal input (video models only).
• TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input.
• V.POSIT, H.POSIT, H.PHASE and H.SIZE cannot be adjusted with a VIDEO signal input
(video models only).
13
Using the Menus (continued)
INPUT Menu
Use this menu to select an input source.
For Video inputs, you must also select a video format.
SETUP
INPUT
IMAGE
OPT.
SETUP
RGB1
RGB2
VIDEO1
VIDEO2
TEST
PATTERN
INPUT
IMAGE
RGB1
RGB2
VIDEO1
VIDEO2
TEST
PATTERN
Item
OPT.
SYSTEM
AUTO
NTSC
PAL
SECAM
Options
RGB1
Selects the RGB 1 terminal.
RGB2
Selects the RGB 2 terminal.
VIDEO1*
Selects the VIDEO 1 terminal.
VIDEO2*
Selects the VIDEO 2 terminal.
TEST PATTERN
Selects the TEST PATTERN. (Start up screen).
SYSTEM
Selects the video signal systems.
* Video models only.
IMAGE Menu
The IMAGE menu controls picture inversion, Size, Reveal and Blanking.
SETUP
INPUT
IMAGE
OPT.
SETUP
MIRROR
MIRROR
BLANK
REVEAL
DISP. SIZE
MESSAGE
SETUP
INPUT
BLANK
INPUT
IMAGE
OPT.
WHITE
BLUE
BLACK
SETUP
INPUT
REVEAL
IMAGE
NORMAL
H : INVERT
V : INVERT
H&V :
INVERT
IMAGE
OPT.
FAST
MEDIUM
SLOW
14
OPT.
Using the Menus (continued)
Select normal or expanded image size.
SETUP
INPUT
DISP. SIZE
IMAGE
OPT.
SETUP
NORMAL
SMALL
INPUT
MESSAGE
Adjustment Item
IMAGE
OPT.
TURN ON
TURN OFF
Details of adjustment
MIRROR
Inverts the picture horizontally or vertically for ceiling or rear screen projection.
H : INVERT Inverts the picture horizontally.
V : INTERT Inverts the picture vertically.
H&V : INVERT Inverts the picture horizontally and vertically.
BLANK
Selects a color when a blank screen is displayed.
REVEAL
Selects the speed of revealing the image display. Use the menu stick switch to
reveal the image.
DISP. SIZE
MESSAGE
NORMAL :
Displayed clock is same as signal source.
LARGE :
Displayed clock is mach as signal source. (picture is wider)
NOTE: For XGA signals, NORMAL mode will compress the image, and some
lines may be missing. LARGE mode will fill the window.
Turn off the on-screen system messages. (FOCUS, selected source, etc.)
OPT. (Options) Menu
The Option menu allows you to set options for the CONTROL port. This menu can also be used to set the Break
Timer, Display Language and Automatic Shutoff.
SETUP
INPUT
IMAGE
OPT.
COM. SPEED
COM. BITS
TIMER
LANGUAGE
AUTO OFF
15
Using the Menus (continued)
SETUP
SETUP
INPUT
IMAGE
OPT.
COM. SPEED
(bps)
1200
2400
4800
9600
19200
INPUT
OPT.
IMAGE
SETUP
INPUT
COM. BITS
SETUP
INPUT
LANGUAGE
TIMER
SETUP
INPUT
10 min.
IMAGE
AUTO OFF
IMAGE
OPT.
Details of adjustment
COM. SPEED
Select speed of data transmission.
COM. BITS
Select the data format.
7N1... 7 data-bits, No parity, 1 stop bit.
8N1... 8 data-bits, No parity, 1 stop bit.
TIMER
Sets the on-screen timer.
LANGUAGE
Selects a language for the on-screen menu.
(English, Francais, Deutsch, Espanol, Italiano, Norsk, Nederlands)
AUTO OFF
OPT.
7N1
8N1
OPT.
ENGLISH
FRANCAIS
DEUTSCH
ESPANOL
ITALIANO
NORSK
NEDERLANDS
0 min.
STOP
Adjustment Item
16
IMAGE
Set the amount of time before the power will turn off if the input
source is turned off.
Connecting to a Video Source
Available for video models only.
1 . Input signal specifications
S-VIDEO signal
Luminance signal
Chrominance signal
1.0Vp-p, 75 Ω termination
VIDEO signal
AUDIO signal
1.0Vp-p, 75 Ω termination
0.286Vp-p (burst signal), 75 Ω termination
Input
200mVrms, 20 kΩ below (MAX 3.0Vp-p)
Output
0~200mVrms, 1k Ω
2 . Signal input terminal pin-out
Chrominance signal
Ground
Luminance signal
Ground
S VIDEO input (Mini DIN4 pin)
NOTE:
Video input signal terminals have priority in the following order:
1. S-VIDEO input terminal 2. RCA jack input terminal
Connecting to an RGB Signal
1 . Input / output signal specifications
Video signal
Analog 0.7Vp-p 75 Ω termination (Positive polarity)
Horizontal sync signal
TTL level (Positive/negative polarity)
Vertical sync signal
TTL level (Positive/negative polarity)
Composite sync signal TTL level
Audio signal
Input
200mVrms, 20k Ω below (MAX 3.0Vp-p)
Output 0 ∼ 200mVrms, 1k Ω
2 . Signal input / output terminal pin-out
1
Video signal (Red)
9
N.C
2
Video signal (Green)
10 Ground
3
Video signal (Blue)
11 Ground
4
N.C
12 N.C
5
N.C
13 Horizontal/Composite sync signal
6
Ground (for R)
14 Vertical sync signal
7
Ground (for G)
15 N.C
8
Ground (for B)
D-sub 15 pin terminal (Female)
17
Connecting to an RGB Signal (continued)
3 . Example of computer signal
Interlaced /
Non-interlaced
Computer/Signal source
Resolution
H×V
fH
(kHz)
fV
(Hz)
15kHz RGB
(NTSC)
—
15.7
60
VGA-1
(IBM compatible)
640 × 350
31.5
70.1
H, V separate
H: Positive
V: Negative
Non-interlaced
VGA-2
(IBM compatible)
640 × 400
31.5
70.1
H, V separate
H: Negative
V: Positive
Non-interlaced
VGA-3
(IBM compatible)
640 × 480
31.5
59.9
H, V separate
H: Negative
V: Negative
Non-interlaced
Macintosh 13 inch mode
(Apple)
640 × 480
35.0
66.7
H, V separate
H: Negative
V: Negative
Non-interlaced
VESA (72 Hz)
640 × 480
37.9
72.8
H, V separate
H: Negative
V: Negative
Non-interlaced
SVGA
(VESA 60Hz)
800 × 600
37.9
60.3
H, V separate
H: Positive
V: Positive
Non-interlaced
SVGA
(VESA 72Hz)
800 × 600
48.1
72.2
H, V separate
H: Positive
V: Positive
Non-interlaced
∗1
Non-interlaced
SW 2 ON
SW 4 ON
Sync Signal
H, V composite Interlaced
Macintosh 16 inch mode
(Apple)
832 × 624
49.7
74.5
H, V separate
H: Positive
V: Positive
XGA
(VESA 60Hz)
1024 × 768
48.4
60.0
H, V separate
H: Negative
V: Negative
Non-interlaced
XGA
(VESA 75Hz)
1024 × 768
60.0
75.0
H, V separate
H: Positive
V: Positive
Non-interlaced
NOTE:
Note
∗1
SW 1 ON
SW 2 ON
A MAC adapter is necessary to set the resolution mode. The projector is compatible
with 13inch and 16inch mode.
ON
OFF
1 2 3 4 5 6
Sample 16inch mode adaptor
XGA images will be compressed to 800 x 600. Some lines may therefore be missing.
NOTE:
18
Some input sources may not be displayed properly because they are not compatible
with the projector.
Connecting to an RGB Signal (continued)
4 . Initial signal settings
The following signals are initially set. The settings may need to be changed for specific computer types.
Use the Setup menu (page 16) to adjust the settings.
b
a
DATA
HSYNC
c
d
Horizontal Timing (µs)
Computer/Signal sorce
a
b
d
15kHz RGB
9.8
52.7
4.7
63.6
VGA-1
5.7
25.2
3.8
31.8
VGA-2
5.7
25.2
3.8
31.8
VGA-3
5.7
25.2
3.8
31.8
Mac 13inch mode
5.3
21.2
2.1
28.6
VESA (72Hz)
5.4
20.5
1.3
26.7
SVGA (60Hz)
5.4
20.0
3.2
26.4
SVGA (72Hz)
3.7
16.0
2.4
20.8
Mac 16inch mode
5.0
14.5
1.1
20.1
XGA (60Hz)
4.0
16.0
2.8
20.4
XGA (75Hz)
3.6
12.8
1.2
16.6
a
DATA
VSYNC
c
b
c
d
Vertical Timing (µs)
Computer/Signal sorce
a
b
c
d
19.5
240
3
262.5
VGA-1
62
350
2
449
VGA-2
37
400
2
449
VGA-3
35
480
2
525
Mac 13inch mode
42
480
3
525
VESA (72Hz)
31
480
3
520
SVGA (60Hz)
27
600
4
628
SVGA (72Hz)
29
600
6
666
Mac 16inch mode
42
624
4
667
XGA (60Hz)
48
768
8
817
XGA (75Hz)
44
768
3
803
15kHz RGB
19
Connecting to a Control Signal
1 . CONTROL terminal
Mouse
.
Pin No RS232C
PS/2
ADB
1
Serial
TDM
2
CLK
3
DATA
SDATA
4
5
6
SEL0
SEL0
SEL0
7
SEL1
SEL1
SEL1
8
READY
D-sub 15 pin terminal (Male)
9
10
GND
GND
GND
+5V
+5V
GND
11
12
13
RDP
14
TDP
15
Caution Turn off the power of both the projector and computer before connecting to the CONTROL port.
Connect the computer to the CONTROL terminal of the projector using an appropriate cable.
Refer to the instruction manual for each device before connecting them through the CONTROL port.
2 . Mouse emulation
(1)
(2)
(3)
(4)
(5)
Turn the projector and computer off.
Connect the projector and the mouse terminal of computer using an appropriate cable.
Turn on the projector.
Turn on the computer.
Start mouse emulation mode.
If you cannot start mouse emulation, reset the computer with a soft reset or by pressing the reset switch.
NOTE:
20
For some Notebook computers with internal pointing devices, mouse emulation will not work
without disabling the internal pointing device. Check your Notebook PC manual for the correct
procedure to disable the internal pointing device.
Connecting to a Control Signal (continued)
PS/2 mouse
Projector
1
CLK 2
DATA 3
4
5
SEL0 6
SEL1 7
8
9
GND 10
11
+5V 12
13
14
15
ADB (Mac) mouse
Projector
1
SDATA 2
3
4
5
SEL0 6
SEL1 7
8
9
GND 10
11
+5V 12
13
14
15
Serial mouse
Projector
TDM 1
2
3
4
5
SELO 6
SEL1 7
READY 8
9
GND 10
11
12
13
14
15
Computer
1
2
3
4
5
6
DATA
Mini Din 6pin
GND
+5V
CLK
6
5
4
3
1
2
PS/2 cable
Computer
1
2
3
4
ADB
(POWER ON)
GND
+5V
Mini Din 4pin
4
3
1
2
ADB cable
Computer
1
2
3
4
5
6
7
8
9
CD
RD
TD
DTR
GND
DSR
RTS
CTS
RI
D-sub 9pin
2
1
6
3
7
4
8
5
9
Serial cable (option)
21
Connecting to a Control Signal (continued)
3 . Communication settings
(1) Connect the projector and computer using an RS 232C cable.
(2) Turn on the computer. After the computer is fully started, turn on the projector.
(3) Start communication.
Projector
Computer
1
2
3
4
5
6
7
8
9
GND 10
11
12
RDP 13
TDP 14
15
1
2
3
4
5
6
7
8
9
CD
RD
TD
DTR
GND
DSR
RTS
DTS
RI
D-sub 9pin
2
1
6
3
7
4
8
5
9
RS232C cable
4 . Control command codes
Control command table
Projector→Computer
Reply code
Computer→Projector
Ask code
Default code
Set code
Item
22
1st
2nd
data
1st
2nd
1st
2nd
data
1st
2nd
MOUSE
11h
05h
+1
20h
05h
31h
05h
+1
40h
05h
COMMUNICATE
11h
06h
+1
20h
06h
31h
06h
+1
40h
06h
POWER
11h
11h
+1
20h
11h
31h
11h
+1
———
ZOOM
11h
12h
+1
———
31h
12h
+1
———
FOCUS
11h
13h
+1
———
31h
13h
+1
———
MIRROR
11h
14h
+1
20h
14h
31h
14h
+1
40h
14h
INPUT
11h
21h
+1
20h
21h
31h
21h
+1
40h
21h
(VIDEO) SYSTEM
12h
22h
+2
20h
22h
32h
22h
+2
40h
22h
VOLUME
11h
23h
+1
20h
23h
31h
23h
+1
40h
23h
MUTE
11h
24h
+1
20h
24h
31h
24h
+1
40h
24h
BRIGHT
13h
31h
+3
20h
31h
33h
31h
+3
40h
31h
CONTRAST
13h
32h
+3
20h
32h
33h
32h
+3
40h
32h
COLOR
13h
33h
+3
20h
33h
33h
33h
+3
40h
33h
TINT
13h
34h
+3
20h
34h
33h
34h
+3
40h
34h
SHARPNESS
13h
35h
+3
20h
35h
33h
35h
+3
40h
35h
H.PHASE
13h
37h
+3
20h
37h
33h
37h
+3
40h
37h
H.POSIT
14h
38h
+4
20h
38h
34h
38h
+4
40h
38h
H.SIZE
14h
36h
+4
20h
36h
34h
36h
+4
40h
36h
V.POSIT
14h
3Ah
+4
20h
3Ah
34h
3Ah
+4
40h
3Ah
BLANK
11h
41h
+1
20h
41h
31h
41h
+1
40h
41h
REVEAL
11h
42h
+1
20h
42h
31h
42h
+1
———
Connecting to a Control Signal (continued)
Control data table
Item
Data code
MOUSE
00h=stop mouse emulation. 01 ∼ 7Fh=start mouse emulation
COMMUNICATE 0Xh=8N1
1Xh=7N1
X0h=1200bps, X1h=2400bps, X2h=4800bps, X3h=9600bps, X4h=19200bps
POWER
1Eh=Power off, 1Fh=Power on
ZOOM
01-3Fh=Zoom +, 41-7Fh=Zoom- 01, 04 (short) ∼ 3F, 7F (long)
FOCUS
01-3Fh=Focus +, 41-7Fh=Focus- 01, 04 (short) ∼ 3F, 7F (long)
MIRROR
00h=Normal, 01h=H:Invert, 02h=V:Invert, 03h=H & V:Invert
INPUT
11h=VIDEO1, 12h=VIDEO2, 21h=RGB1, 22h=RGB2
VIDEO SYSTEM 00h 00h=Auto, 00h 01h=NTSC
00h 02h=PAL, 00h 03h=SECAM
VOLUME
00h (min) ∼ 7Fh (max)
MUTE
00h=Mute off, 01h=Mute on
BRIGHT
00h 00h 00h (dark) ∼ 00h 00h 7Fh (brighter)
CONTRAST
00h 00h 00h (lower) ∼ 00h 00h 7Fh (higher)
COLOR
00h 00h 00h (less) ∼ 00h 00h 7Fh (more)
TINT
00h 00h 00h (red) ∼ 00h 00h 7Fh (green)
SHARPNESS
00h 00h 00h (soft) ∼ 00h 00h 7Fh (sharp)
H.PHASE
00h 00h 00h ∼ 00h 00h 1Fh
H.POSIT
00h 00h 00h 00h (left) ∼ 00h 00h 7Fh 01h (right)
H.SIZE
00h 00h 02h 06h (narrow) ∼ 00h 00h 1Eh 08h (wide)
V.POSIT
00h 00h 00h 00h (up) ∼ 00h 00h 7Fh 01h (down)
BLANK
0Xh=Blank off
1Xh=Blank on
bit0 0=Blue off, 1=Blue on,
bit2 0=red off, 1=Red on,
REVEAL
NOTE:
bit1 0=Green off,
1=Green on
bit3 0=Not change, 1=Change
X1h=Reveal down, X4h=Reveal right, X=0 (slow) ∼ 7 (fast)
If the computer sends an undefined command code or data code the projector
may not operate properly.
Commands consist of 2 command bytes and following data bytes.
The first byte indicates the kinds of commands and the length of the command.
‘0xH’ : Error-reply
Projector sends to computer.
‘1xH’ : Command reply
Projector sends to computer.
‘2xH’ : Ask command
Computer sends to Projector.
‘3xH’ : Set command
Computer sends to Projector.
‘4xH’ : Default set command Computer sends to Projector.
‘5xH’ — ‘FxH’ : Reserved
‘x’ indicates the length of data bytes.
The second byte indicates the command code ‘yy’ as listed in the command table.
The control data table shows the data byte.
23
Connecting to a Control Signal (continued)
Procedure for checking projector status.
1. The computer sends the command ’20H’ + ‘yyH’ to the projector.
2. The projector replies with the command ‘1xH’ + ‘yyH’ + data bytes.
Procedure for setting projector status
1. The computer sends the command ‘3xH’ + ‘yyH’ + data bytes.
2. The projector changes its status.
3. The projector replies with the command ‘1xH’ + ‘yyH’ + data bytes to indicate its newstatus.
Caution Data bytes in step 3 are not always same as data bytes in step 1.
If the projector cannot accept the status of the step 1 data bytes, the projector will set the proper
status and reply with this new data bytes setting to the computer, or the projector will reply
with the error reply ‘0xH’ + ‘yyH’ + data bytes that are the same as those sent in step 1.
Resetting the defaults
1. The computer sends the command ’40H’ + ‘yyH’
2. The projector changes its status to the default setting.
3. The projector replies with the command ‘1xH’ + ‘yyH’ + data bytes to the computer to indicate a return to
default settings.
NOTE:
If the projector sends a ‘4Dh’ before the command code, the computer will ignore the ‘4Dh’.
Sample of command error
1. The computer sends the command ‘2xH’, ‘3xH’ or ‘4xH’ + ‘yyH’ + data bytes.
2. The projector doesn’t understand this code.
3. The projector replies with the command ‘00H’ + ‘yyH’
Sample of data error
1. The computer sends the command ‘2xH’, ‘3xH’ or ‘4xH’ + ‘yyH’ + data bytes.
2. The projector doesn’t understand these data bytes.
3. The projector replies with the command ‘0xH’ + ‘yyH’ + data bytes (same as step 1).
Sample of framing error
1. The projector detects a framing error.
2. The projector changes to 1200bps 7N1 if not currently set at 1200bps 7N1.
3. The projector replies with ’70H’ + ’70H’ 10 times, every 1 second.
4. When projector receives ’70H’ + ’70H’, it replies ’12H’ + ’03H’ + ’01H’ + ’00H’.
Command byte and data byte interval error
1. If the interval of bytes exceeds 500mS, the projector replies with ’70H’ + ’70H’.
2. Projector waits 1 second for a return command from the computer.
3. If there is no command from the computer, the projector treats it as a framing error.
NOTE:
24
The interval of command bytes and data bytes must be over 1mS and under 500mS.
If it is under 1mS, it may be treated as a framing error. The interval between reply codes and other
codes must be over 40mS.
System Setup
Typical system connections:
AC Outlet
VCR with S-VHS out (video models only)
Computer (Notebook type)
Computer (Desktop type)
VCR, etc. (video models only)
CRT Display
Caution Turn power off to all devices before connecting.
Refer to the instruction manual for each device before connecting.
25
Cleaning the air filter
Clean the air filter about every 100 hours of operation.
1
2
Turn off the MAIN POWER switch of the projector and pull out
the power cord.
Remove the air filter from the bottom.
2
3
Clean the air filter using a vacuum cleaner.
If dirt is still present, wipe the air filter with a cloth moistened with water, or use a neutral detergent and
wipe the filter dry with a dry cloth.
4
Re-install the air filter.
Caution If the air filter is filled with dust, etc., the protection circuit will turn the projector power off.
Lamp Replacement
The estimated operating time of the lamp is approximately 700 hours. The following symptoms indicate that the
lamp should be replaced:
• A dark picture.
• “CHANGE THE LAMP” on-screen message.
• LAMP indicator glows red.
Contact your dealer for replacement lamps.
26
Troubleshooting
Check the following before asking for service.
If trouble continues, call your dealer or Proxima Technical Support.
Phone: 619-457-5500, Worldwide Web: http://www.proxima.com
Problem
Possible Cause
Action
Page
• The Main power is not turned on.
• Turn the MAIN POWER switch on.
9
• The power cord is disconnected.
• Insert the power cord into an AC socket.
6
• The setting of the input source is not
correct.
• Set the correct input using the input
select button of the projector or the
remote control.
6, 7, 9
• Wiring to the projector is not correct.
• Connect the cable correctly.
6, 24
• Wiring to the projector is not correct.
• Connect the cable correctly.
6, 24
• The volume is set to minimum.
• Press the VOL button.
6, 7
• The unit is set in Mute mode.
• Press the MUTE button.
6, 7
Sound is heard with
no picture.
• Wiring to the projector is not correct.
• Connect the cable correctly.
6, 24
• The brightness is set too dark.
• Press the MENU button, select BRIGHT
button.
and press the
12, 13
Color is weak and tint is
incorrect.
The color and tint have been adjusted
incorrectly.
Adjust the color and tint.
12, 13
Picture is dark.
• The brightness and contrast have been
adjusted incorrectly.
• Adjust the brightness and contrast.
12, 13
• The lamp has not been adjusted.
• Replace the lamp with a new one.
Picture is not clear.
Focus is not correct.
Adjust the focus.
6, 7, 9
LAMP indicator glows
red.
Trouble with the lamp.
Turn off the power and let it rest for 20
minutes. Then, turn the power on again.
11, 26
TEMP indicator glows
red.
Inside of the projector is too hot.
Check the ventilation holes.
LAMP indicator blinks
red.
Air filter is detached.
Reseat the air filter.
Power does not turn on.
No picture or sound.
Picture is displayed with
no sound.
26
11
11, 26
27
Specifications
• All specifications are subject to change without notice.
Product type
Liquid crystal projector
Model name
DP5800
Display system
3 sheets of liquid crystal panels, 3 primary color lights shutter system
Liquid crystal
panel
Panel size
1.3 inches
Drive system
TFT active matrix
Number of pixels
(H800 x V600) 480,000 pixels
Lens
Zoom lens F=2.3 ∼ 3.0
Lamp
Metal halide lamp 250W
Speaker
2W
Power supply
AC100 ∼ 120V, 5A / AC220 ∼ 240V, 2A
Power consumption
350W
Usable temperature range
32°F - 95°F (0°C - 35°C)
Dimensions
16.3″ (W) × 6.2″ (H) × 12.5″ (D), 414 mm (W) x 157 mm (H) x 317.5 mm (D)
Weight
19 lbs. (8.5 kg)
Input/Output
terminal
Accessories
f=48.1 ∼ 72.1mm
video signal input
terminal
S VIDEO : Mini DIN4-pin terminal
VIDEO : RCA Jack terminal
AUDIO : RCA Jack terminal
RGB input/output
signal terminal
RGB signal : D-sub 15 pin terminal (Female)
AUDIO
: Stereo mini jack
Control terminal
D-sub 15 pin shrink terminal (Male)
Remote control .............................. 1
POWER cord ................................ 1
BATTERIES AA (or R6P) .............. 2
VGA cable ..................................... 1
MAC adaptor ................................. 1
Video/Audio cable ......................... 1
RS 232C cable .............................. 1
Mouse cable .................................. 2
Dimension diagram
All dimensions shown in inches. (mm)
10.1″
(260 mm)
10.1(260)
12.5″
(317.5 mm)
12.0(305)
16.3″
(414 mm)
16.3(415)
6.2″ (157 mm)
1.6″ (40 mm)
12.6″ (320 mm)
28
Warranty and Servicing
Please read this operating guide before calling for service.
For warranty and service claims, please contact Proxima Corporation
Proxima Corporation
Main Office
Proxima Europe LTD.
9440 Carroll Park Drive
San Diego, CA 92121-2298
U.S.A.
Phone (619) 457-5500
Fax (619) 457-9647
http://www.proxima.com
St. Thomas House
28-32 Spittal Street
Marlow Bucks SL7 1DB
United Kingdom
Phone +44 (0) 1628 481 555
Fax +44 (0) 1628 487 744
7/97 Part Number: 710-00519-1
Printed in USA
Download PDF