Q-See | QSB180 | QSB180 Manual - Q-See

Fingerprint & Keypad Lock
MODEL:
QSB180
TRADEMARKS
All brand names and products are Registered
Trademarks of their respective Companies.
LEGAL DISCLAIMER
See warning on rear cover.
DISCLAIMER
The information in the document is subject to change
without notice. The manufacturer makes no representations or warranties with respect to the contents hereof
and specifically disclaims any implied warranties of
selling or functionality for any particular purpose.
Digital Peripheral Solutions Inc.
S015 E Crystal drive,
Anaheim, CA 92807,
1-877-998-3440.
Q-See tech support in U.S.A.
Mon-Fri:9 am -6 pm PST.
TEL:1-877-998-3440
E-mail:ts@dpsi-usa.com
Website:<www.q-see.com>
USER MANUAL
CONTENTS
1.Introduction
1
1.1 Features
1
1.1.1 Model number
1
1.1.2 Main features
1
1.2 Structure & Components
2
1.3 Size & Weight
2
1.4 Accessories
3
1.5 Technical parameters
4
2.Operation instruction
5
2.1 Operation with a mechanical key
5
2.1.1 Unlocking with a mechanical key
5
2.1.2 Closing with a mechanical key
6
2.2 Wake-up code
6
2.2.1 What is wake-up code?
6
2.2.2 How to change the wake-up code?
6
2.2.3 The principle for key combination of wake-up code.
7
2.2.4 How to restore the default wake-up code?
7
2.3 Unlocking code
8
2.3.1 What is unlocking code?
8
2.3.2 How to change the unlocking code?
8
2.3.3 The principle for key combination of unlocking code.
9
2.3.4 How to restore the default unlocking code?
9
2.3.5 How to unlock with unlocking code?
9
2.4 Fingerprint Enrollment code
10
2.4.1 What is fingerprint enrollment code?
11
Http://www.q-see.com
LOCK
2.4.2 The principle for key combination of fingerprint enrollment code
11
2.5 How to enroll your fingerprint?
11
2.6 How to unlock with enrolled fingerprint?
12
2.7 How to delete enrolled fingerprints?
13
2.8 Passage mode
14
2.8.1 What is passage mode ?
14
2.8.2 How to set the door into passage mode ?
14
2.8.3 How to cancel passage mode ?
15
2.9 How to initialize the lock?
15
3.Installaion
15
3.1 Door requirement
15
3.2
16
Tools required when installing
3.3 Installation template
17
3.4 Installation steps
18
3.5 Tips for installation
19
4.Maintenance
20
4.1 Daily maintenance
20
4.2 Troubleshooting
20
Appendix
21
A.Packing list
21
B.Handle orientation of the lock
22
1.Introduction
1.1 Feature
Model number
Model
QSB180
Picture
Main features
Adopts optical fingerprint sensor, CMOS chip. Fingerprint can't be
duplicated.
Cast-steel structure, suitable for standard door-lock cavity of internal
doors.
Stainless steel single latch, easy to install.
Three ways to unlock: PIN+Fingerprint, PIN or mechanical key.
Capacity: Maximum 138 fingerprint templates.
Keypad combines 4 digits: 0, 1, 2 , 3.
Fingerprint and code can be programmed directly on the lock. No
need any computer.
Passage mode can be set any time.
Http://www.q-see.com
LOCK
With the sensor light and buzzer sound indicators
Weight
Mechanical key used in emergency.
Parts
N.W.
Front plate
0.97
Powered by 4 AA alkaline batteries with low voltage alert function
Stand alone, suitable for office, meeting room, residential, villa, etc.
Back plate
Cylinders
1.2 Structure & Components
Accessories
Total
2.37
QSB180
5
6
4
3
7
2
8
9
10
1
11
12
13
14
15
15
Cylindrical
1
14
Flat screw M4 x 25
4
13
Strike
1
12
Strike plate
1
11
Inside handle
1
10
Screw M5
2
9
Back plate
1
8
Pan screw M4
1
7
Battery
4
6
Battery box
1
5
Battery cover
1
4
Back plate gasket
1
3
Front plate gasket
1
2
Front plate
1
1
Outside handle
Item
Description
1.4 Accessories
Mechanical key
(2pcs)
Strike
(1pc)
Screw cover
(2pcs)
Square spindle
(1pc)
Strike plate
(1pc)
Pan screw
M4 L2 (1pc)
Screw connector
A(2pcs) B(1pc)
Fixing screw
M5 L1 (2pcs)
1
Qty
1.3 Size & Weight
Size
(mm)
Sens
orSensor
Sens
or
Indic
ator
Indic
ator
Indicator
Keypa
d
Keypa
d
Keypad
Tapping screw
(4pcs)
M4 X 25
Batte
ryBattery
ver
Batte
rycoco
ver
cover
Front
p
late
Front
p
late
Front
plate
Back
late
Backp
plate
Back
plate
Cylin
drica
l l
Cylin
drica
Cylindrical
Cylinder cover opener
(1pc)
Http://www.q-see.com
LOCK
1.5 Technical parameters
2.Operation instruction
Item
No:
Technical parameters
Fingerprint sensor
Optical sensor
Sensor resolution
500 dpi
Antistrike ability of
sensor surface
Remain good condition after being jabbed
with a 4H pencil at a 20cm's distance.
2.1 Operation with a mechnical key
Unlocking with a mechanical key
Step 1: Take out cylinder cover with cylinder cover opener. (figure 2-1)
Authentication speed
1 second
1:N or 1:1
Authentication methods
FRR
1%
FAR
0.0001%
Angle for putting finger
45
Fingerprint scanning
Once to get one fingerprint template
Step 2: Insert mechanical key into the keyhole, turn the mechanical
Fingerprint template
saved
All enrolled fingerprint template will be saved
while replacing the batteries
handed lock). (figure 2-2)
User capacity
138 max
Light jam
Sunlight resistable
Sensor surface
Optical glass with PVD coated
Operating voltage
4 AA alkaline batteries,DC 4.5~6.0v
Battery life
Approx 12 months
Temperature for storage
-25
10
Static current
Dynamic current
5
key ( 90
anticlockwise if right handed lock, 90
clockwise if left
-85
A
Step 3: Rotate outside handle to unlock the door. (figure 2-3)
110mA~180mA
Operating Environment
Indoor Temperature
Outdoor Temperature
Humidity
NOTE: Mechanical key can unlock the door at any time.
Http://www.q-see.com
LOCK
Closing with a mechanical key
Step 2 : input the previous Wake-up code continuously (the default
Rotate the mechanical key in the keyhole ( 90
handed lock, 90
anticlockwise if right
clockwise if left handed lock) till the mechanical key
code is 0,1,2,3), a long beep is heard and green indicator flash once.
(figure 2-6)
is vertical, draw out the mechanical key. The door is locked.(figure 2-4)
input the previous Wake-up code
the default code is 0,1,2,3
green indicator
flash once
Right Handed
Left Handed
Step 3 : Immediately input twice the new Wake-up code continuously.
If the new code is twice input correctly, a long beep will be heard and
green indicator flashes indicating the success of the operation.
2.2 Wake-up code
(figure 2-7)
input twice the new Wake-up code
What is wake-up code?
Normally, the fingerprint sensor
sleeps
till it is
waken up
green indicator
flashes
by
inputting correct code. Before unlocking the door with fingerprint, one
should input valid code to
wake up
the sensor so that it can
authenticate the enrolled fingerprints. The default wake-up code is
0,1,2,3
How to change the wake-up code?
Step 1 : Press digit
3
and hold it for 6 seconds till you hear a
The principle for key combination of wake-up code
The initial digit of Wake-up code must be 0
beep.(figure2-5)
. For example, you can
choose(0,0,0,0) , or (0,2,2,2) etc. But do remember the wake-up code
Press digit 3 and hold
it for 6 seconds
begins with 0
.
How to restore the default wake-up code?
(0,1,2,3) is the default wake-up code for this lock, if you forgot the
new wake-up code you've modified, you can restore the default wakeup code by following below steps:
Http://www.q-see.com
LOCK
Step 1. Uncover the battery box , take out 1 AA battery (no need to
Step 1: Press digit 3
take all the batteries out).(figure 2-8)
(figure 2-10)
and hold it for 6 seconds till you hear a beep.
Press digit 3 and hold
it for 6 seconds
Step 2: After a beep is heard, input the previous unlocking code
Step 2. Press and hold the digit
0
,
1
,
2
,
3
together and
continuously (the default code is 1,2,3,1,2,3,1,2,3,1,2), a long beep is
replace the battery being taken out. You'll hear a beep within 10
heard. Immediately input the new unlocking code twice continuously,
seconds, release the digit keys after the red and green indicator
(figure 2-11) Caution: For the new unlocking code, the initial digit
flashes, (figure 2-9) Caution: this operation will delete all enrolled
must be
fingerprints saved in the lock. You've got to re-enroll your
correctly, a long beep will be heard and green indicator flashes, which
fingerprint.
confirms the success of the operation.
1
and ends at
2
. If the new code is twice input
input the previous
unlocking code,the
default code is
1,2,3,1,2,3,1,2,3,1,2
2.3 Unlocking code
What is unlocking code?
A code with a combination of 11 digits can unlock the door. The default
unlocking code is 1,2,3,1,2,3,1,2,3,1,2.
How to change the unlocking code?
input the new
unlocking code
twice
The principle for key combination of unlocking code
The initial digit of unlocking code must be
be
2
1
and the last digit must
, total 11 digits, you can fill any digits of 0,1,2,3 in the middle 9
digits. For example, you can choose 1,3,3,3,3,3,3,3,3,3,2.
How to restore the default unlocking code?
The same operation with 2.2.4
Since anybody can unlock the door by inputting unlocking code, you
are recommended to change default unlocking code for higher
security by following below steps:
How to unlock with unlocking code?
Step 1: Press and hold digit 1
(figure 2-12)
for 2 seconds till you hear a beep.
Http://www.q-see.com
LOCK
What is fingerprint enrollment code?
Press and hold digit
1 for 2 seconds
A code with a combination of 11 digits for fingerprint enrollment. The
default fingerprint enrollment code is 2,1,3,2,1,3,2,1,3,2,1.
The principle for key combination of fingerprint
enrollment code
Its order reverses from unlocking code. For example, if the unlocking
code is
Step 2: Input the rest 10 digits of unlocking code continuously ( 2,3,1,
2,3,1,2,3,1,2 if default unlocking code) , if the code is input correctly,
must be
1,2,3,1,2,3,1,2,3,1,2
2,1,3,2,1,3,2,1,3,2,1
, then the fingerprint enrollment code
. If you changed the unlocking code,
the fingerprint enrollment code would be changed automatically.
the green indicator flashes. (figure2-13)
Input the rest 10 digits of
unlocking code continuously
2.5 How to enroll your fingerprint?
Step 1: Input correct Fingerprint Enrollment Code (Let's take the default
green indicator
flashes
enrollment code 21321321321 for example). Press and hold digit
2
for 2 seconds till you hear a beep, and green indicator flashes.
(figure 2-15)
Press and hold digit
2 for 2 seconds
Step 3: Rotate the handle to unlock the door. 5 seconds later the door
will lock automatically. (figure 2-14)
Step 2: Input the rest 10 digits of fingerprint enrollment code
continuously ( 1,3,2,1,3,2,1,3,2,1 if default fingerprint enrollment code) ,
a beep will be heard, red indicator flashes, then put your finger onto
the sensor for enrollment. Move away the finger till you hear 2 beeps,
the green indicator flashes, which indicates the success of the
enrollment. (figure 2-16)
2.4 Fingerprint Enrollment code
Http://www.q-see.com
LOCK
Step 3: Move away the finger and rotate the handle to unlock the door,
5 seconds later the door will be locked again automatically.(figure 2-19)
Input the rest 10
digits of fingerprint
enrollment code
The green indicator
flashes
Put your finger
onto the sensor
The green indicator
flashes,follows 2
beeps
Step 3: Repeat above two steps for more enrollments.
NOTE: To enroll the same finger twice (two templates for one
fingerprint) is recommended.
2.6 How to unlock with enrolled fingerprint?
Step 1: Input 0,1,2,3 continuously, a long beep will be heard, green
indicator flash once, red sensor indicator flashes. (figure 2-17)
2.7 How to delete enrolled fingerprints?
Input wake-up code,e.g.0,1,2,3
Step 1: Press and hold digit
green indicator
flash once
3
for about 6 seconds till you hear a
short beep, as shown in 2-20.
Press and hold digit
for about 6 seconds
3
Step 2: Put an enrolled finger onto the sensor immediately while the
red sensor indicator is flashing. Motor driving will be heard. During
any steps of authentication, if the red indicator flashes after moving
away the finger, a second authentication will be needed. Repeat the
above steps. (figure 2-18)
Put an enrolled finger onto
the sensor
Step 2: Input fingerprint enrollment code continuously (the default
fingerprint enrollment code is 2,1,3,2,1,3,2,1,3,2,1, if you have
changed it, then input the new one), a beep will be heard, a second
beep will follow in 5 seconds, the green indicator flashes, which shows
the successful operation. (Figure 2-21)
Http://www.q-see.com
LOCK
Input fingerprint enrollment
code continuously (the default
fingerprint enrollment code is
2,1,3,2,1,3,2,1,3,2,1
8
How to cancel passage mode ?
There are two options:
A.Input the valid Wake-up Code and the lock come back to close
state. Or,
B.Input the valid unlocking code and the lock come back to close
state.
CAUTION: All the fingerprints enrolled will be deleted.
2.9 How to initialize the lock?
Step 1: Open the battery cover .
2.8 Passage mode
8
Step 2: Take out 1 of the batteries, then replace the battery again after
3 seconds. Press and hold the digits
What is passage mode ?
The lock is in open status all the time. One can rotate the handle and
unlock the door at any time. This operation is suitable for office or
meeting room.
8
0
, 1
, 2
, 3
at the
same time while replacing the battery. Release the digits after the red
and green indicator flashes and a long beep and a short beep are
heard.
CAUTION: The operation will delete all enrolled fingerprints, Please
How to set the door into passage mode?
make sure you wanna do that.
Step 1: Unlock the door with unlocking code or enrolled fingerprint first
refer to 2.3.5 or 2.6;
Step 2: Within 5 seconds after unlocking the door with either
fingerprint or unlocking code, press the digit 0
and hold it for 2
seconds, a long beep is heard and release the press. The lock has
been set into passage mode . You can open the door by rotating the
handle any time till you cancel the setting. (figure 2-22)
Press the digit 0 and
hold it for 2 seconds
3.Installation
3.1 Door requirement
Wooden door with thickness from 3060mm;
110mm
If the door surface is decorated, the
distance from the decorative edge to
the door frame must be above 110mm.
30~60mm
Http://www.q-see.com
LOCK
3.3 Installation template
3.2 Tools required when installing
Model QSB180 lock drilling view(door)
(mm)
Electric drill
Auger bit
Measure
Handle center line
File
Cut-off knife
Screwdriver
Model QSB180 lock
drilling view(doorframe)
Chisel
Pencil
Hammer
Handle center line
Auger
Tape measure
(mm)
3.4 Installation steps
2.Mark the door for drilling
hole with a pencil according
to installation template.
12.Cut grooves for strike
and strike plate with a
chisel .
13.Fix strike and strike
plate in the door frame
with screw M4 x 25.
14.Test the lock as per
operation instruction.
ce
nte
r li
ne
1.Draw handle center line
as your request, the
recommended height for it
is 1m above the ground.
11.Mark position of strike
and strike plate with a
pencil according to
installation template.
Ha
nd
le
Http://www.q-see.com
LOCK
3.Drill the door from both
sides of the door with
4.Drill the latch cavity and
side plate groove.
electric drill.
3.5 Tips for installation
5.Put the latch into latch
cavity, fix the side plate
in the door with screw
M4 x 25.
6.Take apart
the battery
cover , take
out the
batteries.
1.Before you fix the front plate on the door, make sure the protuberant
spot on the back of front plate is in the position as below:
the protuberant spot
7.Fix front plate on the
door.
9.Fix back plate with front
plate by screw M5.
8.Make the square
spindle through the hole
of latch then into the
front plate.
10.Put in the batteries,
close the battery cover. .
There's an indentation here, for either right
or left hand oriented lock,The protuberant
should point straightly to the indentation.
otherwise the clutch won't work.
Inside edge of clutch
2.After the square spindle was put into the clutch of front plate, DO
NOT turn the square spindle;
3.Please rotate the inside handle when tighten the screw under the
handle to avoid scratching the back finish.
Http://www.q-see.com
LOCK
4.Maintenance
Appendix
4.1 Daily maintenance
A Package Contents
A. Keep away from corrosive matter.
B. Do not hang anything on the handle.
C. Keep the sensor surface clean and dry. Wipe it with soft and dry cloth if any
stain on it.
Items
Quantity
Front plate(including rubber gasket )
1pc
Back plate(including rubber gasket )
1pc
Single latch(60mm)
1pc
Single latch (70mm)
1pc
Mechanical keys
2pcs
Cylinder cover opener
1pc
Strike
1pc
Strike plate
1pc
Installation template
2pcs
Accessories pack
4 sets
User manual
1pc
Tools
4pcs
No:
D. When the batteries are running down, the red indicator flashes to alert low
voltage. Although you still can unlock the door 20-30 times, you should
replace the batteries as soon as possible.
E. Keep the mechanical keys carefully to prevent from being burglaried.
4.2 Troubleshooting
Problems
When you put your
enrolled fingerprint onto
the sensor to unlock, red
indicator flashes and
follows two short beeps,
door can't be opened.
When you put your valid
enrolled fingerprint onto
the sensor to unlock, red
indicator flashes and
follows two short beeps,
door can't be opened.
Possible reasons
Solution
1.Invalid fingerprint key
2.Your fingerprint has
already been deleted.
Unlock the door with a
valid fingerprint key.
1.Your fingerprint position
is quite different from
where you first enrolled
2.Bad quality fingerprint.
Put your finger onto the
sensor again, try to put
it onto where you first
enrolled.
Http://www.q-see.com
LOCK
B Handle orientation of the lock
Left handed: Standing out of the door, if the hinge is on the left, it is Left
handed lock.
Right handed: Standing out of the door, if the hinge is on the right, it is Right
handed lock.
Right Handed
Left Handed
~The End~
Download PDF