Mitsubishi | VS-50VA2 | Service manual | Mitsubishi VS-50VA2 Service manual

Revision E:
• MSZ-GE22VAD- A1 has been added.
Please void OBH531 REVISED EDITION-D.
SPLIT-TYPE AIR CONDITIONERS
INDOOR UNIT
SERVICE MANUAL
No. OBH531
REVISED EDITION-E
Models
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD -
A1
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD MSZ-GE60VA MSZ-GE60VAD MSZ-GE71VA MSZ-GE71VAD MSZ-GE80VA MSZ-GE80VA2 MSZ-GE80VAD -
A1
A1
A1
A1
A1
A1
A1
A1
A1
A1
A1
A1
A1
A1
A1
A1
A1
A1
A1
Outdoor unit service manual
MUZ-GE·VA Series (OBH532) MXZ-8A140A (OC316)
MXZ-A·VA Series (OB447)
MXZ-B•VA (OBH567)
CONTENTS
MSZ-GE22VA
MSZ-GE22VAD
MSZ-GE25VA
MSZ-GE25VAD
MSZ-GE33VA
MSZ-GE35VA
MSZ-GE35VA2
MSZ-GE35VAD
MSZ-GE42VA
MSZ-GE42VAD
MSZ-GE50VA
MSZ-GE50VA2
MSZ-GE50VAD
1. TECHNICAL CHANGES ··································· 2
2. PART NAMES AND FUNCTIONS ····················· 3
3. SPECIFICATION ················································ 5
4. NOISE CRITERIA CURVES ······························ 9
5. OUTLINES AND DIMENSIONS ·······················11
6. WIRING DIAGRAM·········································· 12
7. REFRIGERANT SYSTEM DIAGRAM ············· 14
8. SERVICE FUNCTIONS ··································· 15
9. MICROPROCESSOR CONTROL ··················· 17
10. TROUBLESHOOTING ····································· 25
11. DISASSEMBLY INSTRUCTIONS ···················· 45
PARTS CATALOG (OBB531)
NOTE:
RoHS compliant products have <G> mark on the spec name plate.
Use the specified refrigerant only
Never use any refrigerant other than that specified.
Doing so may cause a burst, an explosion, or fire when the unit is being used, serviced, or disposed of.
Correct refrigerant is specified in the manuals and on the spec labels provided with our products.
We will not be held responsible for mechanical failure, system malfunction, unit breakdown or accidents caused by
failure to follow the instructions.
Revision A :
• MSZ-GE60VA- A1 , MSZ-GE71VA- A1 and MSZ-GE80VA- A1 have been added.
Revision B :
• MSZ-GE33VA- A1 and MSZ-GE42VA- A1 have been added.
Revision C:
• MSZ-GE35VA2- A1 , MSZ-GE50VA2- A1 and MSZ-GE80VA2- A1 have been added.
Revision D:
• MSZ-GE25VAD- A1 , MSZ-GE35VAD- A1 , MSZ-GE42VAD- A1 , MSZ-GE50VAD- A1 , MSZ-GE60VAD- A1 , MSZ-GE71VAD- A1
and MSZ-GE80VAD- A1 have been added.
Revision E:
• MSZ-GE22VAD- A1 has been added.
1
TECHNICAL CHANGES
MSZ-GE22VA MSZ-GE25VA MSZ-GE33VA MSZ-GE35VA MSZ-GE42VA MSZ-GE50VA MSZ-GE60VA MSZ-GE71VA MSZ-GE80VA -
A1
A1
A1
A1
A1
A1
A1
A1
A1
1. New model
MSZ-GE35VA - A1
MSZ-GE50VA - A1
MSZ-GE35VA2 - A1
MSZ-GE50VA2 - A1
1. Indoor model name has been changed.
MSZ-GE80VA - A1
MSZ-GE80VA2 - A1
1. Indoor model name has been changed.
2. Indoor electronic control P.C. board has been changed.
MSZ-GE25VA - A1
MSZ-GE35VA2 - A1
MSZ-GE42VA - A1
MSZ-GE50VA2 - A1
MSZ-GE25VAD - A1
MSZ-GE35VAD - A1
MSZ-GE42VAD - A1
MSZ-GE50VAD - A1
1. Indoor electronic control P.C. board has been changed.
2. V.A clamp has been changed.
MSZ-GE60VA - A1
MSZ-GE71VA - A1
MSZ-GE80VA2 - A1
MSZ-GE60VAD - A1
MSZ-GE71VAD - A1
MSZ-GE80VAD - A1
1. Indoor electronic control P.C. board has been changed.
2. Fan guard has been added.
3. Fan operation has been added.
MSZ-GE22VA - A1
MSZ-GE22VAD - A1
1. Indoor electronic control P.C. board has been changed.
OBH531E
2
2
PART NAMES AND FUNCTIONS
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA
MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
Air filter
(Catechin air filter)
Front panel
Air cleaning filter
(Anti-Allergy Enzyme
Filter)
Air inlet
Heat exchanger
Air outlet
Fan guard
Remote controller
Fan
Horizontal vane
Vertical vane
Display section
Remote control receiving section
Operation indicator lamp
Emergency operation switch (E.O. SW)
MSZ-GE60VA MSZ-GE71VA MSZ-GE80VA MSZ-GE80VA2
Front panel
Air filter
(Nano platinum filter)
Air cleaning filter
(Electrostatic anti-allergy
enzyme filter)
Air inlet
Heat exchanger
Remote controller
Air outlet
Fan
Horizontal vane
Vertical vane
Display section
Operation indicator lamp
Emergency operation switch (E.O. SW)
Remote control receiving section
OBH531E
3
MSZ-GE60VAD MSZ-GE71VAD MSZ-GE80VAD
Front panel
Air filter
(Nano platinum filter)
Air cleaning filter
(Electrostatic anti-allergy
enzyme filter)
Air inlet
Heat exchanger
Remote controller
Air outlet
Fan guard
Fan
Horizontal vane
Vertical vane
Display section
Operation indicator lamp
Emergency operation switch (E.O. SW)
Remote control receiving section
ACCESSORIES
Model
MSZ-GE22VA
MSZ-GE22VAD
MSZ-GE25VA
MSZ-GE25VAD
MSZ-GE33VA
MSZ-GE35VA MSZ-GE50VA
MSZ-GE35VA2 MSZ-GE50VA2
MSZ-GE35VAD MSZ-GE50VAD
MSZ-GE42VA
MSZ-GE42VAD
Installation plate
Installation plate fixing screw 4 × 25 mm
Remote controller holder
Fixing screw for 3.5 × 16 mm (Black)
Battery (AAA) for remote controller
Wireless remote controller
Felt tape (For left or left-rear piping)
Air cleaning filter
OBH531E
1
5
1
2
2
1
1
2
4
MSZ-GE60VA
MSZ-GE60VAD
MSZ-GE71VA
MSZ-GE71VAD
MSZ-GE80VA
MSZ-GE80VA2
MSZ-GE80VAD
1
7
1
2
2
1
1
2
3
SPECIFICATION
Indoor model
29
23
0.22
0.29
0.23
RC0J40-FK
0.22
0.29
0.23
798 × 295 × 232
10
5
-
678
762
546
402
288
246
-
Cooling
2)
2)
42
43
36
29
21
30
22
19
-
42
43
36
29
21
30
22
19
-
1,020
1,120
860
670
530
470
Fan speed
Cooling
Heating
Sound level
Special remarks
Heating
690
546 (420
402 (354
288
246
-
Heating
1,040
860 (700 2)
670 (610 2)
530
470
5
KM09A
NOTE: Test conditions are based on AS/NZS 3823.1.1.
Cooling: Indoor Dry-bulb temperature 27°C Wet-bulb temperature
19°C
Outdoor Dry-bulb temperature 35°C Wet-bulb temperature (24°C)
Heating: Indoor Dry-bulb temperature 20°C Wet-bulb temperature 15.5°C
Outdoor Dry-bulb temperature 7°C Wet-bulb temperature
6°C
1 Measured under rated operating frequency. 2 For multi system.
OBH531E
MSZMSZMSZGE35VA GE35VA2 GE35VAD
Single phase 230 V, 50 Hz
22
Airflow
Cooling
Fan
motor
Electrical
data
Power supply
Cooling
W
Heating
Cooling
Running
A
current 1
Heating
Model
Cooling
A
Current 1
Heating
Dimensions W × H × D
mm
Weight
kg
Air direction
Super High
+ LONG + POWERFUL
Super High
High
Med.
m3/h
Low
Quiet
Super High
+ LONG + POWERFUL
Super High
High
m3/h
Med.
Low
Quiet
Super High
+ LONG + POWERFUL
Super High
High
Med.
dB (A)
Low
Quiet
Super High
+ LONG + POWERFUL
Super High
High
Med.
dB (A)
Low
Quiet
Super High
+ LONG + POWERFUL
Super High
High
Med.
rpm
Low
Quiet
Super High
+ LONG + POWERFUL
Super High
High
rpm
Med.
Low
Quiet
Fan speed regulator
Remote controller model
Power input
1
MSZMSZMSZMSZMSZGE22VA GE22VAD GE25VA GE25VAD GE33VA
5
Indoor model
MSZ-GE42VAD
Heating
Fan speed
Cooling
Heating
Sound level
Cooling
Heating
Airflow
Cooling
Electrical
data
0.29
0.31
Special remarks
MSZ-GE50VA
43
39
0.39
0.36
RC0J40-FK
0.39
0.36
798 × 295 × 232
10
5
-
768
624
516
408
348
906
714
576
468
390(420 2)
-
786
624
516
420
348
870
732 (612
576 (540
468
390
2)
2)
46
40
35
30
26
49
44
38
33
28
-
46
40
35
30
26
48
43
37
33
28
-
1,120
950
810
680
600
1,280
1,060
890
750
650 (690 2)
-
1,140
950 (930 2)
810
690
600
1,240
1,080(930 2)
890 (840 2)
750
650
5
KM09A
NOTE: Test conditions are based on AS/NZS 3823.1.1.
Cooling: Indoor Dry-bulb temperature 27°C Wet-bulb temperature
19°C
Outdoor Dry-bulb temperature 35°C Wet-bulb temperature (24°C)
Heating: Indoor Dry-bulb temperature 20°C Wet-bulb temperature 15.5°C
Outdoor Dry-bulb temperature 7°C Wet-bulb temperature
6°C
1 Measured under rated operating frequency. 2 For multi system.
OBH531E
MSZ-GE50VA2 MSZ-GE50VAD
Single phase 230 V, 50 Hz
29
30
0.29
0.31
Fan
motor
Power supply
Cooling
Power input
W
1
Heating
Cooling
Running
A
current 1
Heating
Model
Cooling
A
Current 1
Heating
Dimensions W × H × D
mm
Weight
kg
Air direction
Super High
+ LONG + POWERFUL
Super High
High
Med.
m3/h
Low
Quiet
Super High
+ LONG + POWERFUL
Super High
High
Med.
m3/h
Low
Quiet
Super High
+ LONG + POWERFUL
Super High
High
Med.
dB (A)
Low
Quiet
Super High
+ LONG + POWERFUL
Super High
High
Med.
dB (A)
Low
Quiet
Super High
+ LONG + POWERFUL
Super High
High
Med.
rpm
Low
Quiet
Super High
+ LONG + POWERFUL
Super High
High
rpm
Med.
Low
Quiet
Fan speed regulator
Remote controller model
MSZ-GE42VA
6
Indoor model
MSZGE60VA
MSZGE60VAD
MSZGE71VA
Cooling
1,254
1,074
1,068
MSZGE80VA2
MSZGE80VAD
65
65
0.55
0.55
58
58
0.51
0.51
0.55
0.55
0.51
0.51
1,338
1,254
1,074
1,068
1,338
1,254
1,074
1,068
Heating
Airflow
924
798
690
582
1,338
1,254
1,074
1,068
924
798
690
612
53
Cooling
49
45
41
37
Sound level
30
52
Heating
49
45
41
37
30
Heating
Fan speed
Cooling
Special remarks
1,338
1,330
1,300
1,330
1,300
1,110
980
870
780
680
1,140
1,010
900
800
700
1,110
980
870
780
680
1,140
1,010
900
800
700
1,330
1,300
1,330
1,300
1,110
980
870
780
710
1,140
1,010
900
800
730
5
SG12D
1,110
980
870
780
710
1,140
1,010
900
800
730
SG10A
SG12D
SG10A
NOTE: Test conditions are based on AS/NZS 3823.1.1.
Cooling: Indoor Dry-bulb temperature 27°C Wet-bulb temperature
19°C
Outdoor Dry-bulb temperature 35°C Wet-bulb temperature (24°C)
Heating: Indoor Dry-bulb temperature 20°C Wet-bulb temperature 15.5°C
Outdoor Dry-bulb temperature 7°C Wet-bulb temperature
6°C
1 Measured under rated operating frequency. 2 For multi system.
OBH531E
MSZGE80VA
Single phase 230 V, 50 Hz
65
58
65
58
0.55
0.51
0.55
0.51
RC0J56-AF
0.55
0.51
0.55
0.51
1,100 × 325 × 238
16
5
Power input
1
Fan
motor
Electrical
data
Power supply
Cooling
39
48
W
Heating
61
62
Cooling
0.34
0.43
Running
A
current 1
Heating
0.52
0.53
Model
Cooling
0.34
0.43
A
Current 1
Heating
0.52
0.53
Dimensions W × H × D
mm
Weight
kg
Air direction
Super High
1,236
1,200
+ LONG + POWERFUL
1,098
Super High
High
942
936
Med.
810
804
m3/h
Low
684
678
Quiet
588
Super High
1,236
1,338
+ LONG + POWERFUL
1,098
Super High
High
936
942(882 2)
m3/h
Med.
810
804
Low
684
678
Quiet
588
Super High
52
+ LONG + POWERFUL
Super High
High
Med.
dB (A)
Low
Quiet
29
Super High
+ LONG + POWERFUL
Super High
High
Med.
dB (A)
Low
Quiet
29
Super High
1,260
1,280
+ LONG + POWERFUL
Super High
1,070
1,090
High
940
960
Med.
rpm
830
850
Low
720
740
Quiet
640
660
Super High
1,260
1,280
+ LONG + POWERFUL
Super High
1,070
1,090
High
960
940(890 2)
Med.
rpm
830
850
Low
720
740
Quiet
640
660
Fan speed regulator
Remote controller model
SG10A
SG12D
MSZGE71VAD
7
Specifications and rated conditions of main electric parts
Fuse
Horizontal vane motor
Vertical vane motor
MSZ-GE60VA MSZ-GE71VA
MSZ-GE60VAD MSZ-GE70VAD
MSZ-GE80VA MSZ-GE80VA2
MSZ-GE80VAD
Varistor
Terminal block
OBH531E
T3.15AL250V
12 VDC
(F11)
(MV), (MV1)
(MV2)
12 VDC
(NR11)
(TB)
S10K300E2K1 [ERZV10D471(MSZ-GE22/25/33/35/42/50),ERZV14D471(MSZ-GE60/71/80)]
3P
8
4
NOISE CRITERIA CURVES
MSZ-GE22VA
MSZ-GE25VA
MSZ-GE22VAD
MSZ-GE25VAD
FAN SPEED FUNCTION
Super High
SPL(dB(A))
COOLING
42
HEATING
42
MSZ-GE33VA MSZ-GE35VA
MSZ-GE35VA2 MSZ-GE35VAD
LINE
Super High
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
HEATING
43
LINE
63
125
250
500
1000
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
2000
4000
10
8000
63
125
Super High
46
HEATING
46
500
1000
2000
4000
8000
MSZ-GE50VA MSZ-GE50VA2
MSZ-GE50VAD
SPL(dB(A))
COOLING
250
BAND CENTER FREQUENCIES, Hz
MSZ-GE42VA MSZ-GE42VAD
FAN SPEED FUNCTION
NC-20
NC-10
BAND CENTER FREQUENCIES, Hz
LINE
FAN SPEED FUNCTION
Super High
SPL(dB(A))
COOLING
49
HEATING
48
LINE
90
OCTAVE BAND SOUND PRESSURE LEVEL, 0 dB = 20μPa
90
OCTAVE BAND SOUND PRESSURE LEVEL, 0dB=20μPa
43
NC-20
NC-10
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
63
125
250
500
1000
2000
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
4000
NC-20
NC-10
10
8000
63
125
250
500
1000
2000
4000
BAND CENTER FREQUENCIES, Hz
BAND CENTER FREQUENCIES, Hz
OBH531E
80
NC-20
NC-10
10
COOLING
90
OCTAVE BAND SOUND PRESSURE LEVEL, 0 dB = 20μPa
OCTAVE BAND SOUND PRESSURE LEVEL, 0 dB = 20μPa
90
10
SPL(dB(A))
FAN SPEED FUNCTION
9
8000
MSZ-GE60VA MSZ-GE60VAD
FAN SPEED FUNCTION
Super High
MSZ-GE71VA MSZ-GE71VAD
SPL(dB(A))
COOLING
49
HEATING
49
LINE
FAN SPEED FUNCTION
Super High
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
HEATING
49
63
125
250
500
1000
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
NC-20
NC-10
2000
4000
10
8000
63
125
BAND CENTER FREQUENCIES, Hz
250
500
1000
2000
4000
BAND CENTER FREQUENCIES, Hz
MSZ-GE80VA MSZ-GE80VA2
MSZ-GE80VAD
FAN SPEED FUNCTION
Super High
SPL(dB(A))
COOLING
49
HEATING
49
LINE
Test conditions
Cooling: Dry-bulb temperature
Wet-bulb temperature
Heating: Dry-bulb temperature
Wet-bulb temperature
OCTAVE BAND SOUND PRESSURE LEVEL, 0 dB = 20μPa
90
80
INDOOR UNIT
WALL
70
1m
NC-70
0.8m
60
NC-60
MICROPHONE
50
NC-50
40
NC-40
30
NC-30
20
NC-20
NC-10
10
LINE
80
NC-20
NC-10
10
49
90
OCTAVE BAND SOUND PRESSURE LEVEL, 0 dB = 20μPa
OCTAVE BAND SOUND PRESSURE LEVEL, 0 dB = 20μPa
90
SPL(dB(A))
COOLING
63
125
250
500
1000
2000
4000
8000
BAND CENTER FREQUENCIES, Hz
OBH531E
10
27°C
19°C
20°C
15.5°C
8000
5
OUTLINES AND DIMENSIONS
Unit: mm
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA
MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
11×20 Oblong hole
798
785
225
80
3
42
155
338
315
84
Air in
232
253
231.5
211.5
212.5
155
41
254
6.5
61
5
225
21.5
11×26 Oblong hole
80
Installation plate
Wall hole ø65
Indoor unit
Installation plate
50
619
42
130
56
69
45
8
100
56
69
295
Piping
Drain hose
107
112
Air out
Piping
43
42
19
159
58
50
56
Insulation
Liquid line
Gas line
Drain hose
ø35 O.D
ø6.35 - 0.5 m (Flared connection ø6.35)
ø9.52 - 0.43 m
(Flared connection: ø9.52 (22/25/33/35/42), ø12.7 (50))
Insulation ø28 O.D Connected part ø16 O.D
MSZ-GE60VA MSZ-GE60VAD MSZ-GE71VA MSZ-GE71VAD
MSZ-GE80VA MSZ-GE80VA2 MSZ-GE80VAD
11×20 Oblong hole
225
110
21.5
225
49.5
238
199.5
500.5
3
199.5
44
Indoor unit
439.5
Air in
Installation plate
110.5
45
238.5
258.5
280
5
281
239.5
1100
1090
11×26 Oblong hole
129
Installation plate
Wall hole Ø75
325
210
5
843
181
65
( 70° )
18
Air out
125
160
184
Drain hose
63
63
30
65
Piping
MSZ-GE60
193
60
76
3
63
100
65
12
67
Piping
65
Insulation
Liquid line
Gas line
Drain hose
Ø50 O.D
Ø9.52 - 0.5m (Flared connection Ø6.35)
Ø12 - 0.43m (Flared connection Ø15.88)
Insulation Ø28 Connected part Ø16 O.D
Piping
MSZ-GE71 MSZ-GE80
OBH531E
11
Insulation
Liquid line
Gas line
Drain hose
Ø50 O.D
Ø9.52 - 0.5m (Flared connection Ø9.52)
Ø12 - 0.43m (Flared connection Ø15.88)
Insulation Ø28 Connected part Ø16 O.D
6
WIRING DIAGRAM
MSZ-GE22VA MSZ-GE25VA MSZ-GE33VA MSZ-GE35VA MSZ-GE35VA2
MSZ-GE22VAD MSZ-GE25VAD MSZ-GE35VAD
MSZ-GE42VA MSZ-GE50VA MSZ-GE50VA2
OBH531E
12
MSZ-GE42VAD MSZ-GE50VAD
MSZ-GE60VA MSZ-GE71VA MSZ-GE80VA MSZ-GE80VA2
MSZ-GE60VAD MSZ-GE71VAD MSZ-GE80VAD
OBH531E
13
7
REFRIGERANT SYSTEM DIAGRAM
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA
MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
Refrigerant pipe ø9.52 (MSZ-GE22/25/33/35/42)
ø12.7 (MSZ-GE50)
(with heat insulator)
Indoor
heat
exchanger
Indoor coil
thermistor
RT12 (main)
Flared connection
Indoor coil
thermistor
RT13 (sub)
Room temperature
thermistor
RT11
Flared connection
Refrigerant pipe ø6.35
(with heat insulator)
Refrigerant flow in cooling
Refrigerant flow in heating
MSZ-GE60VA MSZ-GE60VAD MSZ-GE71VA MSZ-GE71VAD
MSZ-GE80VA MSZ-GE80VA2 MSZ-GE80VAD
Refrigerant pipe ø15.88
(with heat insulator)
Indoor
heat
exchanger
Indoor coil
thermistor
RT12 (main)
Flared connection
Indoor coil
thermistor
RT13 (sub)
Room temperature
thermistor
RT11
Flared connection
Refrigerant pipe ø6.35 (MSZ-GE60)
ø9.52 (MSZ-GE71/80)
(with heat insulator)
Refrigerant flow in cooling
Refrigerant flow in heating
OBH531E
14
Unit: mm
8
SERVICE FUNCTIONS
MSZ-GE22VA
MSZ-GE35VA
MSZ-GE50VA
MSZ-GE71VA
MSZ-GE22VAD
MSZ-GE35VA2
MSZ-GE50VA2
MSZ-GE71VAD
MSZ-GE25VA
MSZ-GE35VAD
MSZ-GE50VAD
MSZ-GE80VA
MSZ-GE25VAD
MSZ-GE42VA
MSZ-GE60VA
MSZ-GE80VA2
MSZ-GE33VA
MSZ-GE42VAD
MSZ-GE60VAD
MSZ-GE80VAD
8-1. TIMER SHORT MODE
For service, the following set time can be shortened by bridging JPG and JPS on the electronic control P.C. board. (Refer
to 10-7.2,3.)
Set time: 3 minutes → 3 seconds (It takes 3 minutes for the compressor to start operation. However, the starting time is
shortened by bridging JPG and JPS.)
8-2. P.C. BOARD MODIFICATION FOR INDIVIDUAL OPERATION
A maximum of 4 indoor units with wireless remote controllers can be used in a room.
In this case, to operate each indoor unit individually by each remote controller, P.C. boards of remote controller must be
modified according to the number of the indoor unit.
How to modify the remote controller P.C. board
Remove batteries before modification.
The board has a print as shown below:
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA
MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
NOTE: For modification, take out
the batteries and press the
OPERATE/STOP (ON/OFF)
button 2 or 3 times at first.
After modification, put back
the batteries then press the
RESET button.
J1
J2
MSZ-GE60VA MSZ-GE60VAD MSZ-GE71VA MSZ-GE71VAD
MSZ-GE80VA MSZ-GE80VA2 MSZ-GE80VAD
J1
J2
The P.C. board has the print “J1” and “J2”. Solder “J1” and “J2” according to the number of indoor unit as shown in Table 1.
After modification, press the RESET button.
Table 1
No. 1 unit
No. 2 unit
No. 3 unit
No. 4 unit
1 unit operation
No modification
—
—
—
2 units operation
Same as at left
Solder J1
—
—
3 units operation
Same as at left
Same as at left
Solder J2
—
4 units operation
Same as at left
Same as at left
Same as at left
Solder both J1 and J2
How to set the remote controller exclusively for particular indoor unit
After you turn the breaker ON, the first remote controller that sends the signal to the indoor unit will be regarded as the remote
controller for the indoor unit.
The indoor unit will only accept the signal from the remote controller that has been assigned to the indoor unit once they are set.
The setting will be cancelled if the breaker is turned OFF, or the power supply is shut down.
Please conduct the above setting once again after the power has restored.
15
OBH531E
8-3. AUTO RESTART FUNCTION
When the indoor unit is controlled with the remote controller, the operation mode, the set temperature, and the fan speed
are memorized by the indoor electronic control P.C. board. “AUTO RESTART FUNCTION” automatically starts operation in
the same mode just before the shutoff of the main power.
Operation
If the main power has been cut, the operation settings remain.
After the power is restored, the unit restarts automatically according to the memory.
(However, it takes at least 3 minutes for the compressor to start running.)
How to disable “AUTO RESTART FUNCTION”
Turn off the main power for the unit.
Solder the jumper wire to JR07 on the indoor electronic control P.C. board. (Refer to 10-7.3.)
(MSZ-GE22/25/33/35/42/50/60/71/80VA, MSZ-GE35/50/82VA2, MSZ-GE22/25/35/42/50VAD)
Cut the jumper wire to JR77 on the indoor electronic control P.C. board. (Refer to 10-7.3.)
(MSZ-GE60/71/80VAD)
JR07
CN112
CN151 CN152 CN111
CN10A
CN151
CN112 CN111
Indoor electronic
control P.C. board
MSZ-GE60VA
MSZ-GE71VA
MSZ-GE80VA MSZ-GE80VA2
CN10A
MSZ-GE22VA
MSZ-GE22VAD
MSZ-GE25VA
MSZ-GE25VAD
MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD
MSZ-GE42VA
MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
Indoor electronic
control P.C. board
JR07
MSZ-GE60VAD
MSZ-GE71VAD
MSZ-GE80VAD
CN10A
CN151 CN152 CN111
CN112
JR77
Indoor electronic
control P.C. board
NOTE:
• The operation settings are memorized when 10 seconds have passed after the indoor unit was operated with the remote
controller.
• If main power is turned OFF or a power failure occurs while AUTO START/STOP timer is active, the timer setting is cancelled.
• If the unit has been off with the remote controller before power failure, the auto restart function does not work as the
power button of the remote controller is OFF.
• To prevent breaker OFF due to the rush of starting current, systematize other home appliance not to turn ON at the same
time.
• When some air conditioners are connected to the same supply system, if they are operated before power failure, the
starting current of all the compressors may flow simultaneously at restart.
Therefore, the special counter-measures are required to prevent the main voltage-drop or the rush of the starting current
by adding to the system that allows the units to start one by one.
OBH531E
16
9
MICROPROCESSOR CONTROL
MSZ-GE22VA
MSZ-GE35VA
MSZ-GE50VA
MSZ-GE71VA
MSZ-GE22VAD
MSZ-GE35VA2
MSZ-GE50VA2
MSZ-GE71VAD
MSZ-GE25VA
MSZ-GE35VAD
MSZ-GE50VAD
MSZ-GE80VA
MSZ-GE25VAD
MSZ-GE42VA
MSZ-GE60VA
MSZ-GE80VA2
MSZ-GE33VA
MSZ-GE42VAD
MSZ-GE60VAD
MSZ-GE80VAD
WIRELESS REMOTE CONTROLLER
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
Signal transmitting section
Operation display section
OPERATE/STOP
(ON/OFF) button
Temperature buttons
FAN SPEED CONTROL button
OPERATION SELECT button
OFF TIMER button
ECONO COOL button
ON TIMER button
VANE CONTROL button
TIME SET buttons
FORWARD button
BACKWARD button
i save button
RESET button
CLOCK SET button
Indication of
remote controller
model is on back
MSZ-GE60VA MSZ-GE71VA MSZ-GE80VA MSZ-GE80VA2
Signal transmitting section
LONG button
WIDE VANE CONTROL button
Operation display section
OPERATION SELECT button
ECONO COOL button
POWERFUL button
Temperature buttons
FAN SPEED CONTROL button
VANE CONTROL button
TIME, TIMER set buttons
FORWARD button
BACKWARD button
i save button
OPERATE/STOP
(ON/OFF) button
WEEKLY TIMER
set button
RESET button
Indication of
remote controller
model is on back
CLOCK SET button
NOTE: Last setting will be stored after the unit is turned OFF with the remote controller. Indoor unit receives the signal of the
remote controller with beeps.
OBH531E
17
MSZ-GE60VAD MSZ-GE71VAD MSZ-GE80VAD
Signal transmitting section
LONG button
WIDE VANE CONTROL button
OPERATION SELECT button
Operation display section
FAN SPEED CONTROL button
ECONO COOL button
VANE CONTROL button
TIME, TIMER set buttons
FORWARD button
BACKWARD button
POWERFUL button
i save button
Temperature buttons
WEEKLY TIMER
set button
OPERATE/STOP
(ON/OFF) button
RESET button
CLOCK SET button
Indication of
remote controller
model is on back
NOTE: Last setting will be stored after the unit is turned OFF with the remote controller. Indoor unit receives the signal of the
remote controller with beeps.
INDOOR UNIT DISPLAY SECTION
Operation Indicator lamp
The operation indicator at the right side of the indoor unit indicates the operation state.
•The following indication applies regardless of shape of the indication.
Indication
Operation state
Room temperature
The unit is operating to
reach the set temperature
About 2°C or more away
from set temperature
Lighted
The room temperature is
approaching the set temperature
About 1 to 2°C from set
temperature
Not lighted
Standby mode
(Only during multi system
operation)
Blinking
-
9-1. COOL ( ) OPERATION
(1) Press OPERATE/STOP (ON/OFF) button.
OPERATION INDICATOR lamp of the indoor unit turns on with a beep tone.
(2) Select COOL mode with OPERATION SELECT button.
(3) Press TEMPERATURE buttons [TOO WARM or TOO COOL button (MSZ-22/25/33/35/42/50)/TEMP
or
button
(MSZ-GE60/71/80)] to select the desired temperature. The setting range is 16 - 31°C.
1. Coil frost prevention
The compressor operational frequency is controlled by the temperature of the indoor heat exchanger to prevent the coil
from frosting.
When the temperature of indoor heat exchanger becomes too low, the coil frost prevention mode works.
The indoor fan operates at the set speed and the compressor stops. This mode continues until the temperature of indoor
heat exchanger rises.
2. Low outside temperature operation
When the outside temperature is lower, low outside temperature operation starts, and the outdoor fan slows or stops.
3. Indoor fan speed control
When the thermostat turns OFF, the indoor fan stops running to reduce power consumption.
After that, the indoor fan stops for 60 seconds and then operates at Very Low for 10 seconds to sense accurate room
temperature. The indoor fan alternates ON and OFF at this interval while the thermostat is OFF.
When the room temperature rises and the thermostat is ON, the indoor fan starts running according to the settings on
the remote controller. (MSZ-GE60/71/80)
OBH531E
18
9-2. DRY ( ) OPERATION
(1) Press OPERATE/STOP (ON/OFF) button.
OPERATION INDICATOR lamp of the indoor unit turns on with a beep tone.
(2) Select DRY mode with OPERATION SELECT button.
(3) The set temperature is determined from the initial room temperature.
1. Coil frost prevention
Coil frost prevention works the same way as that in COOL mode. (9-1.1.)
2. Low outside temperature operation
Low outside temperature operation works the same way as that in COOL mode. (9-1.2.)
3. Indoor fan speed control
Indoor fan speed control works the same way as that in COOL mode. (9-1.3.)
9-3. HEAT ( ) OPERATION
(1) Press OPERATE/STOP (ON/OFF) button.
OPERATION INDICATOR lamp of the indoor unit turns on with a beep tone.
(2) Select HEAT mode with OPERATION SELECT button.
or
button
(3) Press TEMPERATURE buttons [TOO WARM or TOO COOL button (MSZ-22/25/33/35/42/50)/TEMP
(MSZ-GE60/71/80)] to select the desired temperature. The setting range is 16 - 31°C.
1. Cold air prevention control
When the compressor is not operating or is starting, and the temperature of indoor heat exchanger and/or the room temperature is low or when defrosting is being done, the indoor fan will stop or rotate in Very Low speed.
2. High pressure protection
The compressor operational frequency is controlled by the temperature of the indoor heat exchanger to prevent the condensing pressure from increasing excessively.
When the temperature of indoor heat exchanger becomes too high, the high pressure protection works.
The indoor fan operates following the cold air prevention control. This mode continues until the temperature of indoor
heat exchanger falls.
3. Defrosting
Defrosting starts when the temperature of outdoor heat exchanger becomes too low.
The compressor stops once, the indoor/outdoor fans stop, the 4-way valve reverses, and the compressor re-starts.
This mode continues until the temperature of outdoor heat exchanger rises or the fixed time passes.
9-4. FAN ( )OPERATION (MSZ-GE60/71/80VAD)
(1) Press OPERATE/STOP (ON/OFF) button. OPERATION INDICATOR lamp of the indoor unit turns ON with a beep tone.
(2) Select FAN mode with OPERATION SELECT button.
(3) Select the desired fan speed. When AUTO, it becomes Low. Only indoor fan operates. Outdoor unit does not operate.
9-5. AUTO CHANGE OVER ··· AUTO MODE OPERATION
Once desired temperature is set, unit operation is switched automatically between COOL and HEAT operation.
Mode selection
(1) Initial mode
When unit starts the operation with AUTO operation from OFF:
• If the room temperature is higher than the set temperature, operation starts in COOL mode.
• If the room temperature is equal to or lower than the set temperature, operation starts in HEAT mode.
(2) Mode change
COOL mode changes to HEAT mode when about 15 minutes have passed with the room temperature 1°C below the
set temperature.
HEAT mode changes to COOL mode when about 15 minutes have passed with the room temperature 1°C above the
set temperature.
NOTE 1
If two or more indoor units are operating in multi system, there might be a case that the indoor unit, which is operating in
(AUTO), cannot change over to the other operating mode (COOL ↔ HEAT) and becomes a state of standby.
Refer to NOTE 2 “FOR MULTI SYSTEM AIR CONDITIONER”.
NOTE 2
FOR MULTI SYSTEM AIR CONDITIONER OUTDOOR UNIT: MXZ series
Multi system air conditioner can connect two or more indoor units with one outdoor unit.
• When you try to operate two or more indoor units with one outdoor unit simultaneously, one for the cooling and the others for
heating, the operation mode of the indoor unit that operates first is selected. Other indoor units cannot operate, and operation
indicator lamp flashes as shown in the figure below. In this case, please set all the indoor units to the same operation mode.
OPERATION INDICATOR
Lighted
Blinking
Not lighted
• When indoor unit starts the operation while the defrosting of outdoor unit is being done, it takes a few minutes (max. 10 minutes) to blow out the warm air.
• In the heating operation, though indoor unit that does not operate may get warm or the sound of refrigerant flowing may be
heard, they are not malfunction. The reason is that the refrigerant continuously flows into it.
OBH531E
19
9-6. AUTO VANE OPERATION
1. Horizontal vane
(1) Vane motor drive
These models are equipped with a stepping motor for the horizontal vane. The rotating direction, speed, and angle of
the motor are controlled by pulse signals (approximately 12 V) transmitted from indoor microprocessor.
(2) The horizontal vane angle and mode change as follows by pressing VANE CONTROL button.
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
AUTO
1
2
3
4
5
SWING
MSZ-GE60VA MSZ-GE60VAD MSZ-GE71VA MSZ-GE71VAD
MSZ-GE80VA MSZ-GE80VA2 MSZ-GE80VAD
AUTO
1
2
3
4
5
SWING
(3) Positioning
To confirm the standard position, the vane moves until it touches the vane stopper. Then the vane is set to the
selected angle.
Confirming of standard position is performed in the following cases:
(a) When the operation starts or finishes (including timer operation).
(b) When the test run starts.
(c) When standby mode (only during multi system operation) starts or finishes.
(4) VANE AUTO ( ) mode
In VANE AUTO mode, the microprocessor automatically determines the vane angle to make the optimum room temperature distribution.
In COOL and DRY operation
In HEAT operation
Vane angle is fixed to Horizontal position.
Vane angle is fixed to Angle 5.
Horizontal
position
5
(5) STOP (operation OFF) and ON TIMER standby
In the following cases, the horizontal vane returns to the closed position.
(a) When OPERATE/STOP (ON/OFF) button is pressed (POWER OFF).
(b) When the operation is stopped by the emergency operation.
(c) When ON TIMER is ON standby.
(6) Dew prevention
During COOL or DRY operation with the vane angle at Angle 4 or 5 when the compressor cumulative operation time
exceeds 1 hour, the vane angle automatically changes to Angle 1 for dew prevention.
(7) SWING ( or
) mode
By selecting SWING mode with VANE CONTROL button, the horizontal vane swings vertically.
(8) Cold air prevention in HEAT operation
The horizontal vane position is set to Upward.
NOTE: When 2 or more indoor units are operated with multi outdoor unit, even if any indoor unit turns thermostat off,
this control does not work in the indoor unit.
(9) ECONO COOL ( ) operation (ECONOmical operation)
When ECONO COOL button is pressed in COOL mode, set temperature is automatically set 2°C higher by the
microprocessor. [However, the temperature on the LCD screen on the remote controller is not changed. (MSZGE60/71/80)] Also the horizontal vane swings in various cycle.
SWING operation makes you feel cooler than set temperature. So, even though the set temperature is higher, the
air conditioner can keep comfort. As a result, energy can be saved.
To cancel this operation, select a different mode or press one of the following buttons in ECONO COOL operation:
ECONO COOL, VANE CONTROL, LONG (MSZ-GE60/71/80) or POWERFUL (MSZ-GE60/71/80) button.
(10) POWERFUL (
) operation (MSZ-GE60/71/80)
The air conditioner automatically adjusts the fan speed and the set temperature, and operates the POWERFUL mode.
The POWERFUL mode is cancelled automatically 15 minutes after operation starts, or when POWERFUL button
is pressed once again within 15 minutes after operation starts. The operation mode returns to the mode prior to
POWERFUL operation. To manually cancel this operation. Select a different mode or press one of the following buttons: OPERATE/STOP (ON/OFF), ECONO COOL, FAN SPEED CONTROL or i-save button.
OBH531E
20
(11) LONG MODE (
) (MSZ-GE60/71/80)
By pressing LONG button indoor fan speed becomes faster than setting fan speed on the remote controller, and the
horizontal vane moves to the position for LONG mode. The remote controller displays “
”. LONG mode is cancelled when LONG button is pressed once again or VANE CONTROL button is pressed or ECONO COOL button is
pressed in COOL mode. In the following example, the vertical vane is set to
(front.).
COOL / DRY / HEAT / AUTO CHANGE OVER
Fan speed : Faster
Solid arrow : When the LONG mode is used.
Dotted arrow : When the LONG mode is not used.
2. Vertical vane (MSZ-GE60/71/80)
(1) Vane motor drive
These models are equipped with a stepping motor for the vertical vane. The rotating direction, speed, and angle of
the motor are controlled by pulse signals (approximately 12 V) transmitted from microprocessor.
(2) The vertical vane angle and mode change as follows by pressing WIDE VANE CONTROL button.
(3) Positioning
To confirm the standard position, the vane moves until it touches the vane stopper. Then the vane is set to the selected angle.
1
2
3
4
5
6
(SWING)
Confirming of standard position is performed in the following cases:
(a) OPERATE/STOP (ON/OFF) button is pressed (POWER ON).
(b) SWING is started.
(4) SWING (
) MODE
By selecting SWING mode with WIDE VANE CONTROL button, the vertical vane swings horizontally. The remote
controller displays “
”. Swing mode is cancelled when WIDE MODE CONTROL button is pressed once again.
9-7. TIMER OPERATION
1. How to set the time
(1) Check that the current time is set correctly.
NOTE: Timer operation will not work without setting the current time. Initially “0:00” blinks at the current time display
of TIME MONITOR, so set the current time correctly with CLOCK SET button.
How to set the current time
(a) Press the CLOCK set button.
and
/
and
) to set the current time.
(b) Press the TIME SET buttons (
• Each time FORWARD button (
/
) is pressed, the set time increases by 1 minute, and each time
BACKWARD button (
/
) is pressed, the set time decreases by 1 minute.
• Pressing those buttons longer, the set time increases/decreases by 10 minutes.
(c) Press the CLOCK set button.
(2) Press OPERATE/STOP (ON/OFF) button to start the air conditioner.
(3) Set the time of timer.
ON timer setting
(a) Press ON TIMER button(
/
) during operation.
(b) Set the time of the timer using TIME SET buttons (
and
/
and
).
OFF timer setting
/
) during operation.
(a) Press OFF TIMER button (
(b) Set the time of the timer using TIME SET buttons (
and
/
and
).
Each time FORWARD button (
/
) is pressed, the set time increases by 10 minutes: each time
BACKWARD button (
/
) is pressed, the set time decreases by 10 minutes.
2. To release the timer
To release ON timer, press ON TIMER button (
/
).
/
).
To release OFF timer, press OFF TIMER button(
TIMER is cancelled and the display of set time disappears.
21
OBH531E
PROGRAM TIMER
• OFF timer and ON timer can be used in combination. The timer of the set time that is reached first will operate first.
• “ / ” and “ / ” display shows the order of OFF timer and ON timer operation.
(Example 1) The current time is 8:00 PM.
(Example 2) The current time is 11:00 AM.
The unit turns off at 11:00 PM, and on at 6:00 AM.
The unit turns on at 5:00 PM, and off at 9:00 PM.
MSZ-GE22/25/33
MSZ-GE35/42/50
MSZ-GE22/25/33
MSZ-GE35/42/50
MSZ-GE60/71/80
MSZ-GE60/71/80
NOTE: If the main power is turned OFF or a power failure occurs while ON/OFF timer is active, the timer setting is cancelled. As these models are equipped with an auto restart function, the air conditioner starts operating with timer
cancelled when power is restored.
9-8. WEEKLY TIMER OPERATION (MSZ-GE60/71/80)
• A maximum of 4 ON or OFF timers can be set for individual days of the week.
• A maximum of 28 ON or OFF timers can be set for a week.
NOTE:
• The simple ON/OFF timer setting is available while the weekly timer is on. In this case, the ON/OFF timer has priority over the weekly
timer; the weekly timer operation will start again after the simple ON/OFF timer is complete.
• When the weekly timer is set, temperature cannot be set to 10°C.
• The weekly timer operation and i-save operation cannot be used together.
1. How to set the weekly timer
* Make sure that the current time and day are set correctly.
(1) Press
button to enter the weekly timer setting mode.
*
(2) Press
and
blinks.
buttons to select setting day and number.
E.g. : [Mon Tue ... Sun]
and [1] are selected.
Pressing
selects the day of
the week to be set.
Pressing
selects
the setting number.
* All days can be selected.
OBH531E
22
(3) Press
,
, and
buttons to set ON/OFF, time, and temperature.
E.g. : [ON], [6:00]
and [24°C] are
selected.
Pressing
selects ON/OFF timer.
Pressing
deletes timer setting.
Pressing
Pressing
adjusts the time.
adjusts the temperature.
* Hold down the button to change the time quickly.
Press
and
buttons to continue setting the timer for other days and/or numbers.
button to complete and transmit the weekly timer setting.
(4) Press
*
which was blinking goes out, and the
current time will be
displayed.
NOTE:
• Press
button to transmit the setting information of weekly timer to the indoor unit. Point the remote controller toward the
indoor unit for 3 seconds.
• When setting the timer for more than one day of the week or one number,
button once after all the settings are complete. All the weekly timer settings will be saved.
setting. Press
• Press
button does not have to be pressed per each
button to enter the weekly timer setting mode, and press and hold
button for 5 seconds to erase all weekly
timer settings. Point the remote controller toward the indoor unit.
(5) Press
button to turn the weekly timer ON. (
lights.)
•When the weekly timer is ON, the day of the week whose timer setting is complete, will light.
Press
button again to turn the weekly timer OFF. (
goes out.)
NOTE:
The saved settings will not be cleared when the weekly timer is turned OFF.
2. Checking weekly timer setting
(1) Press
*
button to enter the weekly timer setting mode.
blinks.
(2) Press
(3) Press
or
buttons to view the setting of the particular day or number.
button to exit the weekly timer setting.
NOTE:
When all days of the week are selected to view the settings and a different setting is included among them,
displayed.
OBH531E
23
will be
9-9. i-save ( ) OPERATION
1. How to set i-save operation
(1) Press OPERATE/STOP (ON/OFF) button.
(2) Select COOL, HEAT or ECONO COOL mode.
(3) Press i-save button.
(4) Set the temperature, fan speed, and airflow direction for i-save operation.
NOTE:
• i-save operation cannot be selected during DRY or AUTO mode operation.
• The setting range of HEAT mode i-save operation is 10°C and 16 - 31°C.
• 2 groups of setting can be saved. (One for COOL/ECONO COOL, one for HEAT)
• i-save operation and the weekly timer operation cannot be used together.
2. How to cancel operation
• Press i-save button again.
• i-save operation can also be cancelled by pressing OPERATION SELECT button to change the operation mode.
The same setting is select from the next time by simply pressing i-save button.
9-10. EMERGENCY/TEST OPERATION
In the case of test run operation or emergency operation, use
EMERGENCY OPERATION switch on the right side of the indoor unit.
Emergency operation is available when the remote controller is missing or has failed, or when the batteries in the remote controller are
running down. The unit will start and OPERATION INDICATOR lamp
will light up.
The first 30 minutes of operation is the test run operation. This operation is for servicing. The indoor fan runs at High speed and the temperature control does not work.
After 30 minutes of test run operation, the system shifts to
EMERGENCY COOL/HEAT MODE with a set temperature of 24°C.
The fan speed shifts to Med.
The coil frost prevention works even in the test run or the emergency operation.
In the test run or emergency operation, the horizontal vane operates in
VANE AUTO ( ) mode.
Emergency operation continues until EMERGENCY OPERATION
switch is pressed once or twice or the unit receives any signal from
the remote controller. In the latter case, normal operation will start.
Operation mode
Set temperature
Fan speed
Horizontal vane
COOL/HEAT
24°C
Med.
Auto
The operation mode is indicated by the
Operation Indicator lamp as following
Operation Indicator lamp
EMERGENCY COOL
↓
EMERGENCY HEAT
↓
Lighted
Not lighted
STOP
NOTE: Do not press EMERGENCY OPERATION switch during normal operation.
Emergency
operation switch
(E.O. SW)
9-11. 3-MINUTE TIME DELAY OPERATION
When the system turns OFF, compressor will not restart for 3 minutes as 3-minute time delay function operates to protect
compressor from overload.
OBH531E
24
10
TROUBLESHOOTING
MSZ-GE22VA
MSZ-GE35VA
MSZ-GE50VA
MSZ-GE71VA
MSZ-GE22VAD
MSZ-GE35VA2
MSZ-GE50VA2
MSZ-GE71VAD
MSZ-GE25VA
MSZ-GE35VAD
MSZ-GE50VAD
MSZ-GE80VA
MSZ-GE25VAD
MSZ-GE42VA
MSZ-GE60VA
MSZ-GE80VA2
MSZ-GE33VA
MSZ-GE42VAD
MSZ-GE60VAD
MSZ-GE80VAD
10-1. CAUTIONS ON TROUBLESHOOTING
1. Before troubleshooting, check the following
1) Check the power supply voltage.
2) Check the indoor/outdoor connecting wire for miswiring.
2. Take care of the following during servicing
1) Before servicing the air conditioner, be sure to turn OFF the main unit first with the remote controller, and after confirming the horizontal vane is closed, turn OFF the breaker and/or disconnect the power plug.
2) Be sure to turn OFF the power supply before removing the front panel, the cabinet, the top panel, and the P.C. board.
3) When removing the P.C. board, hold the edge of the board with care NOT to apply stress on the components.
4) When connecting or disconnecting the connectors, hold the housing of the connector. DO NOT pull the lead wires.
<Incorrect>
<Correct>
Lead wiring
Housing point
3. Troubleshooting procedure
1) Check if the OPERATION INDICATOR lamp on the indoor unit is flashing ON and OFF to indicate an abnormality.
To make sure, check how many times the OPERATION INDICATOR lamp is flashing ON and OFF before starting service work.
2) Before servicing, check that the connector and terminal are connected properly.
3) When the P.C. board seems to be defective, check the copper foil pattern for disconnection and the components for
bursting and discoloration.
4) When troubleshooting, Refer to 10-2, 10-3 and 10-4.
4. How to replace batteries
Weak batteries may cause the remote controller malfunction.
In this case, replace the batteries to operate the remote controller normally.
Remove the front lid and insert batteries.
Then reattach the front lid.
Press RESET button with a thin instrument, and
then use the remote controller.
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
Insert the negative pole of the
batteries first. Check if the polarity
of the batteries is correct.
RESET button
MSZ-GE60VA MSZ-GE60VAD MSZ-GE71VA MSZ-GE71VAD
MSZ-GE80VA MSZ-GE80VA2 MSZ-GE80VAD
Insert the negative pole of the
batteries first. Check if the polarity
of the batteries is correct.
RESET button
NOTE: 1. If RESET button is not pressed, the remote controller may not operate correctly.
2. This remote controller has a circuit to automatically reset the microcomputer when batteries are replaced.
This function is equipped to prevent the microcomputer from malfunctioning due to the voltage drop caused by the
battery replacement.
3. Do not use the leaking batteries.
OBH531E
25
5. How to install the horizontal vane
If horizontal vane is not installed correctly, all of the operation indicator lamps will blink.
In this case, install the horizontal vane correctly by following the procedures to .
NOTE: Before installation of the horizontal vane, turn OFF the power supply.
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
2
In procedure lock the
stoppers until they click
into place.
Lock
1
MSZ-GE60VA MSZ-GE71VA MSZ-GE80VA MSZ-GE80VA2
Lock
Check the upper and the lower vane.
MSZ-GE60VAD MSZ-GE71VAD MSZ-GE80VAD
Lock
Check the upper and the lower vane.
OBH531E
26
10-2. FAILURE MODE RECALL FUNCTION
Outline of the function
This air conditioner can memorize the abnormal condition which has occurred once.
Even though LED indication listed on the troubleshooting check table (10-4.) disappears, the memorized failure details
can be recalled.
This mode is very useful when the unit needs to be repaired for the abnormality which does not recur.
1. Flow chart of failure mode recall function for the indoor/outdoor unit
MSZ-GE22/25/33/35/42/50VA
MSZ-GE35/50VA2
MSZ-GE22/25/35/42/50VAD
MSZ-GE60/71/80VA
MSZ-GE80VA2
MSZ-GE60/71/80VAD
Operational procedure
The cause of abnormality cannot be found because the abnormality does not recur.
Setting up the failure mode recall function
Turn ON the power supply.
<Preparation of the remote controller>
While pressing both OPERATION SELECT button and TOO COOL button (MSZbutton (MSZ-GE60/71/80) on the remote controlGE22/25/33/35/42/50)/TEMP
ler at the same time, press RESET button.
First, release RESET button.
Hold down the other two buttons for another 3 seconds. Make sure that the indicators on the LCD screen shown in the right figure are all displayed. Then release
the buttons.
Press OPERATE/STOP (ON/OFF) button of the remote controller (the set temperature is displayed) with the remote controller headed towards the indoor unit. 1
Does upper lamp of OPERATION INDICATOR
lamp on the indoor unit blink at the interval of 0.5
seconds?
Blinks: Either indoor or outdoor unit is abnormal.
Beep is emitted at the same timing as the
blinking of upper lamp of OPERATION
INDICATOR lamp. 2
Yes
(Blinks)
Judgment of indoor/outdoor abnormality
Before blinking, does upper lamp of
OPERATION INDICATOR lamp stay ON for 3
seconds?
Yes
Stays ON for 3 seconds (without beep):
The outdoor unit is abnormal.
No
No
(OFF)
Indoor unit is normal.
But the outdoor unit might be abnormal because there are
some abnormalities that cannot be recalled with this way.
Check if outdoor unit is abnormal according to the detailed
outdoor unit failure mode recall function.
1 Regardless of normal or abnormal condition, a short beep is
emitted once the signal is received.
The outdoor unit is abnormal.
Check the blinking pattern, and identify the abnormal point by referring
to the outdoor unit failure mode table. (Refer to outdoor unit service
manual.)
Make sure to check at least two consecutive blinking cycles. 3
The indoor unit is abnormal.
Check the blinking pattern, and identify the abnormal point by referring to the
indoor unit failure mode table. (Refer to 10-2.2)
Make sure to check at least two consecutive blinking cycles. 2
Releasing the failure mode recall function
Release the failure mode recall function by the following procedures.
Turn OFF the power supply and turn it ON again.
Press RESET button of the remote controller.
Repair the failure parts.
Deleting the memorized abnormal condition
After repairing the unit, recall the failure mode again according to "Setting up the failure mode recall
function" mentioned above.
Press OPERATE/STOP (ON/OFF) button of the remote controller (the set temperature is displayed)
with the remote controller headed towards the indoor unit.
Press EMERGENCY OPERATION switch so that the memorized abnormal condition is deleted.
Release the failure mode recall function according to "Releasing the failure mode recall function"
mentioned above.
NOTE: 1. Make sure to release the failure mode recall function after it is set up, otherwise the unit cannot operate properly.
2. If the abnormal condition is not deleted from the memory, the last abnormal condition is kept memorized.
2. Blinking pattern when the indoor unit is abnormal:
Blinking at 0.52.5-second OFF second interval
Blinking at 0.52.5-second OFF second interval
ON
OFF
Beeps
Repeated cycle
Beeps
Repeated cycle
3.Blinking pattern when the outdoor unit is abnormal:
Blinking at 0.52.5-second OFF
3-second ON
second interval
Beeps
Repeated cycle
2.5-second OFF
3-second ON
Blinking at 0.5second interval
ON
OFF
No beep
Repeated cycle
OBH531E
No beep
Repeated cycle
Beeps
27
Beeps
Repeated cycle
2. Indoor unit failure mode table
Upper lamp of OPAbnormal point
ERATION INDICA(Failure mode)
TOR lamp
Not lighted
Normal
Condition
Remedy
—
—
The room temperature thermistor short or
1-time flash every Room temperature
open circuit is detected every 8 seconds dur0.5-second
thermistor
ing operation.
Refer to the characteristics of the room temperature
thermistor (10-7.2,3.).
2-time flash
2.5-second OFF
Indoor coil
thermistor
The indoor coil thermistor short or open circuit Refer to the characteristics of the main indoor coil theris detected every 8 seconds during operation. mistor, the sub indoor coil thermistor (10-7.2,3.).
3-time flash
2.5-second OFF
Serial signal
The serial signal from outdoor unit is not received for a maximum of 6 minutes.
11-time flash
2.5-second OFF
Indoor fan motor
The rotational frequency feedback signal is not
emitted for the 12 seconds after the indoor fan Refer to 10-6.
operation.
12-time flash
2.5-second OFF
Indoor control
system
It cannot properly read data in the nonvolatile
memory of the indoor electronic control P.C.
board.
Refer to 10-6.
signal error".
"How to check miswiring and serial
"Check of indoor fan motor".
Replace the indoor electronic control P.C. board.
NOTE: Blinking patterns of this mode differ from the ones of TROUBLESHOOTING CHECK TABLE (10-4.).
OBH531E
28
10-3. INSTRUCTION OF TROUBLESHOOTING
Start
Indoor unit operates.
Outdoor unit
does not operate.
Outdoor unit
operates only
in Test Run
operation.
Outdoor unit
does not
operate even
in Test Run
operation.
Indoor unit operates.
Outdoor unit does
not operate normally.
Unit does not
operate normal operation
in COOL or
HEAT mode.
Indoor unit does
not receive the
signal from remote controller.
Indoor unit
operates, when
EMERGENCY
OPERATION
switch is pressed.
OPERATION INDICATOR
lamp on the indoor unit is
flashing ON and OFF.
"Test Run operation" means the
operation within 30 minutes after EMERGENCY OPERATION
switch is pressed.
Indoor unit does
not operate, when
EMERGENCY
OPERATION
switch is pressed.
If blinking of OPERATION INDICATOR lamp cannot be checked,
it can be checked with failure
mode recall function.
Check room
temperature
thermistor.
Refer to 10-7.
"Test point
diagram and
voltage".
Refer to "How
to check
inverter/compressor".
Refer to
"Check of R.V.
coil".
Refer to 10-6.
"Check of remote
controller and
indoor electronic
control P.C. board".
1. Check indoor/outdoor connecting wire.
(Check if the power is
supplied to the indoor
unit.)
2. Refer to 10-6. "Check
of indoor P.C. board
and indoor fan motor".
Refer to outdoor unit service manual.
All lamps
Flash on and
off at 0.5-second intervals
Cause:
Indoor unit
• The horizontal vane is
not installed
correctly.
Upper lamp
Flash on and
off at 0.5-second intervals
Cause:
Indoor/Outdoor
unit
• Miswiring or
trouble of
serial signal
Upper lamp
2-time flash
Cause:
Indoor unit
• Trouble
of room
temperature
/ indoor coil
thermistor
Upper lamp
3-time flash
Cause:
Indoor unit
• Trouble of
indoor fan
motor
Upper lamp
4-time flash
Cause:
Indoor unit
• Trouble
of indoor
unit control
system
Upper lamp
5-time flash
Cause:
Outdoor unit
• Outdoor
power
system
abnormality
Upper lamp
6-time flash
Cause:
Outdoor unit
• Trouble of
thermistor in
outdoor unit
Upper lamp
7-time flash
Cause:
Outdoor unit
• Trouble of
outdoor control system
Upper lamp
14-time flash
/ or more (VAD)
Cause:
Outdoor unit
• Other abnormality
Refer to
10-6.
"Check of installation of
the horizontal vane".
Refer to
10-6. "How
to check miswiring and
serial signal
error".
Check room
temperature
thermistor
and indoor
coil thermistor. Refer to
10-7. "Test
point diagram
and voltage".
Refer to
10-6.
"Check of
indoor fan
motor".
Replace the
indoor electronic control
P.C. board.
Refer to
"How to
check
inverter/compressor".
Refer to
"Check of
outdoor thermistors".
Replace the
inverter P.C.
board or
the outdoor
electronic
control P.C.
board.
Check "Flow
chart of the
detailed
outdoor unit
failure mode
recall function."
OBH531E
29
10-4. TROUBLESHOOTING CHECK TABLE
Before taking measures, make sure that the symptom reappears for accurate troubleshooting.
When the indoor unit has started operation and detected an abnormality of the following condition (the first detection after the
power ON), the indoor fan motor turns OFF and OPERATION INDICATOR lamp flashes.
OPERATION INDICATOR
Lighted
Blinking
Not lighted
No.
1
Abnormal
point
Miswiring
or serial
signal
Indoor coil
thermistor
2
Room temperature
thermistor
Operation indicator lamp
Symptom
Condition
Upper lamp flashes.
0.5-second ON
Remedy
The serial signal from the outdoor unit is not
received for 6 minutes.
• Refer to 10-6. "How to check
miswiring and serial signal error".
The indoor coil or the room temperature thermistor is short or open circuit.
• Refer to the characteristics of
indoor coil thermistor, and the
room temperature thermistor
(10-7.2,3.).
The rotational frequency feedback signal is
not emitted during the indoor fan operation.
• Refer to 10-6. "Check of indoor fan motor".
It cannot properly read data in the nonvolatile
memory of the indoor electronic control P.C.
board.
• Replace the indoor electronic
control P.C. board.
0.5-second OFF
Upper lamp flashes.
2-time flash
2.5-second OFF
Upper lamp flashes.
3-time flash
3
Indoor fan
motor
2.5-second OFF
Upper lamp flashes.
4-time flash
4
Indoor control system
2.5-second OFF
5
Outdoor
power system
Upper lamp flashes.
5-time flash
Indoor unit and
outdoor unit do
not operate.
2.5-second OFF
to "How to check of inIt consecutively occurs 3 times that the com- • Refer
verter/compressor".
pressor stops for overcurrent protection or
to outdoor unit service
start-up failure protection within 1 minute after Refer
manual.
start-up.
• Check the stop valve.
Upper lamp flashes.
6-time flash
6
Outdoor
thermistors
The outdoor thermistors short or open circuit
during the compressor operation.
• Refer to "Check of outdoor
thermistor".
Refer to outdoor unit service
manual.
It cannot properly read data in the nonvolatile
memory of the inverter P.C. board or the outdoor electronic control P.C. board.
• Replace the inverter P.C. board
or the outdoor electronic control
P.C. board.
Refer to outdoor unit service
manual.
An abnormality other than above mentioned
is detected.
• Check the stop valve.
• Check the 4-way valve. (VAD)
• Check the abnormality in detail
using the failure mode recall
function for outdoor unit.
It cannot properly read data in the nonvolatile
memory of the inverter P.C. board or the outdoor electronic control P.C. board.
• Check the blinking pattern of
the LED on the inverter P.C.
board or the outdoor electronic
control P.C. board.
2.5-second OFF
7
Outdoor
control system
Upper lamp flashes.
7-time flash
2.5-second OFF
Upper lamp flashes.
14-time flash / or more (VAD)
8
Other abnormality
2.5-second OFF
9
Outdoor
control sys- Upper lamp lights up
tem
OBH531E
Outdoor unit
does not operate
30
OPERATION INDICATOR
No.
Abnormal
point
Operation indicator lamp
Symptom
Condition
Remedy
All lamps flash at the same time.
1
Indoor unit and
outdoor unit do
not operate.
Attachment 0.5-second ON
of the horizontal vane 0.5-second OFF
The electricity is not conducted to the interlock switch (Fan) of the horizontal vane.
• Refer to 10-6. "Check of
installation of the horizontal
vane".
OPERATION INDICATOR
No.
Abnormal
point
Operation indicator lamp
Symptom
Condition
Remedy
Upper lamp lights and lower lamp flashes.
1
MXZ type
Operation
mode
setting
The operation mode of the each indoor unit
Outdoor unit
is differently set to COOL (includes DRY) and • Unify the operation mode.
operates but
HEAT at the same time, the operation mode
Refer to outdoor unit service
indoor unit does
of the indoor unit that has operated at first has manual.
not operate.
the priority.
2.5-second OFF
10-5. TROUBLE CRITERION OF MAIN PARTS
MSZ-GE22VA
MSZ-GE35VA
MSZ-GE50VA
MSZ-GE71VA
MSZ-GE22VAD
MSZ-GE35VA2
MSZ-GE50VA2
MSZ-GE71VAD
MSZ-GE25VA
MSZ-GE35VAD
MSZ-GE50VAD
MSZ-GE80VA
MSZ-GE25VAD
MSZ-GE42VA
MSZ-GE60VA
MSZ-GE80VA2
Part name
Room temperature
thermistor (RT11)
Indoor coil thermistor
(RT12, RT13)
Check method and criterion
Measure the resistance with a tester.
Indoor fan motor (MF)
Check 10-6.
MSZ-GE33VA
MSZ-GE42VAD
MSZ-GE60VAD
MSZ-GE80VAD
Figure
Refer to 10-7. "Test point diagram and voltage", "2 or 3. Indoor electronic
control P.C. board", for the chart of thermistor.
BLK
Measure the resistance between the terminals with a tester.
MSZ-GE22/25/33/35/42/50 (Temperature: 10 - 30°C)
Color of the lead wire
Normal
Vane motor (MV)
RED - BLK
223 - 268 Ω
MSZ-GE60/71/80
Horizontal vane motor
(MV1)
Vertical vane motor
(MV2)
OBH531E
ROTOR
BLK
RED
BLK
Measure the resistance between the terminals with a tester.
(Temperature: 10 - 30°C)
Color of the lead wire
Horizontal vane motor (MV1)
Vertical vane motor (MV2)
RED-BLK
31
Normal
313 ~ 375 Ω
268 ~ 322 Ω
BLK
BLK
ROTOR
BLK
RED
BLK
BLK
10-6. TROUBLESHOOTING FLOW
A Check of indoor fan motor
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
The indoor fan motor error has occurred, and the indoor fan does not operate.
Turn OFF the power supply.
Pay enough attention to the high voltage on the fan motor connector CN211.
Is there any foreign matter that interferes
the rotation of the line flow fan?
No
Yes
Remove the foreign matter and
adjust the line flow fan.
Is there 325 VDC
between CN211 (+)
and (–) ?
Turn ON the power supply, wait 5 seconds or more, and then press
EMERGENCY OPERATION switch.
Measure the supply voltage as follows within 12 seconds after EMERGENCY OPERATION switch is pressed.
If more than 12 seconds passes, turn OFF the power supply and turn it
ON again, then measure the voltage.
<Indoor power P.C. board>
1. Measure the voltage between CN211 (+) and (–).
2. Measure the voltage between CN211 (+) and (–).
<Indoor electronic control P.C. board>
3. Measure the voltage between CN10A (+) and JPG (GND)(–).
If more than 12 seconds passes after EMERGENCY OPERATION switch
is pressed, the voltage measured at 2. above goes 0 VDC although the
indoor P.C. board is normal.
Does the voltage between CN211
(+) and (–) on the power P.C. board
rise to the range of 3 to 6 VDC within
12 seconds after EMERGENCY
OPERATION switch is pressed?
Yes
Yes
Replace the indoor fan motor.
No
No
Replace the indoor power
P.C. board and the indoor
terminal P.C. board.
Yes
Does the voltage between CN10A
(+) and JPG (GND)(–) on the indoor
electronic control P.C. board fall to
2 V or less within 12 seconds after
EMERGENCY OPERATION switch is
pressed?
No
Replace the indoor electronic
control P.C. board.
The indoor fan motor error has occurred, and the indoor fan repeats "12-second ON and 30-second OFF" 3 times, and then stops.
Measure the voltage between CN211
(+) and (–) while the fan motor is
rotating.
Is it unchanged holding
0 or 15 V DC?
Yes
(Unchanged)
Measure the voltage CN10A (+)
and JPG (GND)(–) on the indoor
No
electronic control P.C board when
(Changed) the fan motor is rotaring.
Replace the indoor fan motor.
Replace the indoor power P.C.
board and the indoor terminal P.C.
board.
OBH531E
Is it unchanged holding
0 or 5 VDC?
Yes
(Unchanged)
32
No
(Changed)
Replace the indoor
electronic control P.C.
board.
MSZ-GE60VA MSZ-GE60VAD MSZ-GE71VA MSZ-GE71VAD
MSZ-GE80VA MSZ-GE80VA2 MSZ-GE80VAD
The indoor fan motor error has occurred, and the indoor fan does not operate.
Turn OFF the power supply.
Pay enough attention to the high voltage on the fan motor connector CN211.
Is there any foreign matter that interferes
the rotation of the line flow fan?
Yes
Remove the foreign matter and
adjust the line flow fan.
Is there 325 VDC
between CN211 (+)
and (–) ?
No
Turn ON the power supply, wait 5 seconds or more, and then press
EMERGENCY OPERATION switch.
Measure the supply voltage as follows within 12 seconds after EMERGENCY OPERATION switch is pressed.
If more than 12 seconds passes, turn OFF the power supply and turn it
ON again, then measure the voltage.
<Indoor electronic control P.C. board>
1. Measure the voltage between CN211 (+) and (–).
2. Measure the voltage between CN211 (+) and (–).
If more than 12 seconds passes after EMERGENCY OPERATION switch
is pressed, the voltage measured at 2. above goes 0 V DC although the
indoor P.C. board is normal.
Yes
No
Does the voltage between CN211
(+) and (–) on the indoor electronic
control P.C. board rise to the range
of 3 to 6 VDC within 12 seconds after
EMERGENCY OPERATION switch is
pressed?
Yes
Replace the indoor fan motor.
No
Replace the indoor electronic control P.C.
board and the indoor terminal P.C. board.
Replace the indoor electronic control
P.C. board.
The indoor fan motor error has occurred, and the indoor fan repeats "12-second ON and 30-second OFF" 3 times, and then stops.
Measure the voltage between CN211
(+) and (–) while the fan motor is
rotating.
Is it unchanged holding
0 or 15 VDC?
Yes
(Unchanged)
Replace the indoor fan motor.
OBH531E
33
No
(Changed)
Replace the indoor
electronic control P.C.
board.
B Check of remote controller and indoor electronic control P.C. board
Check if the remote controller is exclusive for this air conditioner.
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
Press OPERATE/STOP (ON/OFF)
button on the remote controller.
Is LCD display on the remote controller
visible?
Yes
No
(Not clear)
1 Look at the image of the signal transmitting section of
the remote controller through the monitor of a digital
camera or a camera phone. It is normal if the LED of
the signal transmitting section lights up when the OPERATE/STOP (ON/OFF) button on the remote controller is pressed. However, it may be difficult to see the
illuminated LED of the signal transmitting section with a
smartphone camera.
Replace the batteries. (Refer to 10-1.4.)
Remove the batteries, then set them back
and press RESET button. (Refer to 10-1.4.)
Check if the unit operates with the remote
controller.
Does the unit operate with the remote
controller?
No
2 If the inverter fluorescent light is turned on when the
room is cool, the unit may have difficulty receiving the
signal from the remote controller or may not be able to
operate with it; if the inverter fluorescent light is turned
on when the room is warm, the unit may be able to
operate with the remote controller.
Turn ON a radio to AM and press
OPERATE/STOP (ON/OFF) button on
the remote controller. 1
Yes
OK
Is noise heard from radio?
Yes
Are there any fluorescent lights of
inverter or rapid-start type within the
range of 1 m? 2
No
Yes
Replace the remote controller.
• Reinstall the unit away from lights.
• Attach a filter on receiving part.
No
Replace the indoor electronic control
P.C. board. (Including the receiver)
MSZ-GE60VA MSZ-GE60VAD MSZ-GE71VA MSZ-GE71VAD
MSZ-GE80VA MSZ-GE80VA2 MSZ-GE80VAD
Press OPERATE/STOP (ON/OFF)
button on the remote controller.
Is LCD display on the remote controller
visible?
Yes
No
(Not clear)
Replace the batteries. (Refer to 10-1.4.)
Remove the batteries, then set them back
and press RESET button. (Refer to 10-1.4.)
Check if the unit operates with the remote
controller.
Does the unit operate with the remote
controller?
No
Turn ON a radio to AM and press OPERATE/STOP (ON/OFF) button on the
remote controller. 1
Yes
OK
Is noise heard from radio?
Yes
Are there any fluorescent lights of
inverter or rapid-start type within the
range of 1 m? 2
No
Replace the remote controller.
Yes
• Reinstall the unit away from lights.
• Attach a filter on receiving part.
Yes
Replace indoor electronic control P.C.
board.
No
Measure the voltage between power
monitor receiver SW P.C. board connector CN20A No.2(+) and No.3(-) when the
remote controller button is pressed.
Is the voltage approximately 4 V DC?
No
Replace power monitor receiver SW P.C. board.
OBH531E
34
C Check of indoor P.C. board and indoor fan motor
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
Turn OFF the power supply.
Remove indoor fan motor connector CN211
from indoor power P.C. board and vane
motor connector CN151 from the indoor
electronic control P.C. board and turn ON
the power supply.
Does the unit operate with the remote
controller?
Does OPERATION INDICATOR lamp light
up by pressing EMERGENCY OPERATION
switch?
Yes
Measure the resistance of indoor fan
motor.
Refer to 10-5.
Short circuit:
Replace the indoor fan motor.
Measure the resistance of the vane
motor coil.
Refer to 10-5.
Short circuit:
Replace the vane motor and the indoor
electronic control P.C. board.
No
Replace the varistor (NR11)
and fuse (F11). 3
Yes
Is the varistor (NR11)
burnt and the fuse (F11)
blown?
Turn OFF the power supply.
Check both “parts side” and “pattern
side” of the indoor terminal P.C.
board visually.
No
Be sure to check both the fuse
and the varistor in any case.
Is the fuse (F11) blown
only?
1. The fan motor connector's lead wire is red, whereas
is black.
2. Connect "+" of the tester to fan motor connector's
lead wire, and “-” to lead wire, otherwise the
resistance cannot be measured properly.
3. Please replace the fuse after removing the indoor
terminal P.C. board from the electrical box.
No
Yes
Measure the resistance between
CN211 (+) and (-) of indoor fan
motor connector. 1, 2
Is the resistance 1MΩ or more?
Yes
No
Replace the fuse (F11) and the
indoor fan motor. 3
Replace the fuse (F11). 3
Measure the resistance of resistor
(R111) on the indoor power P.C.
board (MSZ-GE22/25/33/35).
Measure the resistance of reactor
(L111) on the indoor power P.C.
board (MSZ-GE42/50).
Is the resistance of resistor (R111)
approximately 4 Ω (MSZ-GE22/25/33/35)?
Is the resistance of reactor (L111)
approximately 2.2 Ω (MSZ-GE42/50)?
No
Replace the indoor
power P.C. board, the
indoor terminal P.C.
board and the indoor fan
motor.
Yes
Indoor electronic control
P.C. board
JPG (GND)
CN10A
Is the approximately 5 VDC between
5 V (+) and JPG (GND) (-) of the
indoor electronic control P.C. board?
Is there approximately 9 V to 13 VDC
between 12 V (+) and JPG (GND) (-)
of the indoor electronic control P.C.
board?
No
Are connector CN10A on the
indoor electronic control P.C.
board or lead wires disconnected?
No
Yes
Yes
12 VDC
Replace the indoor electronic control P.C. board.
5 VDC
Indoor terminal
P.C. board
Indoor power P.C. board
R111 (MSZ-GE22/25/33/35)
L111 (MSZ-GE42/50)
Fuse (F11)
Varistor
(NR11)
OBH531E
CN211
35
Replace the indoor fan motor.
Connect the connector or repair disconnection.
MSZ-GE60VA MSZ-GE60VAD MSZ-GE71VA MSZ-GE71VAD
MSZ-GE80VA MSZ-GE80VA2 MSZ-GE80VAD
Turn OFF the power supply.
Remove indoor fan motor connector CN211 and vane motor
connector CN151 and CN152 from the indoor electronic
control P.C. board and turn ON the power supply.
Measure the resistance between CN211
and of the indoor fan motor connector.
Short circuit:
Replace the indoor fan motor.
Measure the resistance of the horizontal vane
motor coil.
Refer to 10-5.
Short circuit:
Replace the horizontal vane motor and the indoor
electronic control P.C. board.
Yes
Does the unit operate with the remote controller?
Does OPERATION INDICATOR lamp light up by
pressing EMERGENCY OPERATION switch?
No
Replace the varistor (NR11) and fuse (F11).
Yes
Are the varistor (NR11) burnt
and the fuse (F11) blown?
Turn OFF the power supply.
Check both “parts side” and “pattern
side” of the indoor electronic control P.C.
board visually.
No
Be sure to check both the fuse
and the varistor in any case.
Is the fuse (F11) blown only?
No
Yes
1. The fan motor connector's
is black.
2. Connect "+" of the tester to fan motor connector's lead
wire, and "-" to lead wire, otherwise the resistance cannot be
measured properly.
3. Please replace the fuse after removing the indoor terminal
P.C. board from the electrical box.
Measure the resistance between
CN211 (+) and (-) of the indoor
fan motor connector. 1, 2
No
Is the resistance 1MΩ
or more?
lead wire is red, whereas
Replace the fuse (F11) and the indoor fan motor. 3
Yes
Replace the fuse (F11). 3
Measure the resistance of cement
resistor R111 on the indoor electronic
control P.C. board.
Is the resistance
approximately 4Ω?
No
Yes
Replace the indoor electronic control P.C. board.
Indoor terminal
P.C. board
Indoor electronic
control P.C.Board
Fuse
(F11)
R111
Varistor
(NR11)
OBH531E
CN211
36
Replace the indoor electronic control P.C. board
and the indoor fan motor.
D How to check miswiring and serial signal error
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
Turn OFF the power supply.
Is there rated voltage in the power supply?
Yes
Check the power supply.
No
Turn ON the power supply.
Is there rated voltage between the outdoor terminal block S1 and S2?
Yes
No
Check the wiring.
Press EMERGENCY OPERATION switch once.
Does the upper lamp of OPERATION INDICATOR lamp light up? <Confirmation of the power
to the indoor unit>
Yes
Is serial signal error indicated 6 minutes later?
No
No
Yes
A
Turn OFF the power supply.
Check once more if the indoor/outdoor
B connecting wire is not miswiring.
Bridge the outdoor terminal block S2 and
S3. 1
Turn ON the power supply.
Is there any miswiring,
poor contact, or wire
disconnection of the
indoor/outdoor connecting wire?
No
Yes
Correct them.
1. Miswiring may damage indoor electronic control P.C.
board during the operation.
Be sure to confirm the wiring is correct before the operation starts.
3. Be sure to check this within 3 minutes after turning ON.
After 3 minutes, LED blinks 6 times. Even when the
inverter P.C. board or the outdoor electronic control P.C.
board is normal, LED blinks 6 times after 3 minutes.
(Except for outdoor unit of multi system type)
Is the bus-bar voltage of the inverter P.C. board or the outdoor electronic control P.C. board normal?
(Refer to "TEST POINT DIAGRAM AND VOLTAGE" of the outdoor unit.)
No
Check of power supply.
Yes
Does the LED on the inverter P.C. board or the outdoor electronic control P.C.
board repeat "3.6-second-OFF and 0.8-second-ON quick blinking"? 3
Yes
Turn OFF the power supply.
Remove the bridge between the outdoor terminal block S2 and S3.
Turn ON the power supply.
Is there rated voltage between the indoor terminal block S1 and S2?
<Confirmation of power voltage>
No
Yes
Is there amplitude of 10 to 20 VDC between the indoor terminal block
S2 and S3? <Confirmation of serial signal>
No
(Lighted
or not
lighted)
Replace the inverter P.C. board or the outdoor
electronic control P.C. board. 2
2. Be careful of the residual voltage of smoothing
capacitor.
Check the wiring.
If there are any error of the indoor/outdoor connecting wire:
such as the damage of the wire, intermediate connection,
and/or poor contact to the terminal block, replace the indoor/
outdoor connecting wire.
No
Yes
A
• Turn OFF inverter-controlled lighting
equipment.
• Turn OFF the power supply and then
turn ON again.
• Press EMERGENCY OPERATION
switch.
Is serial signal
error indicated
6 minutes later?
Yes
B
OBH531E
• Reinstall
either the unit
or the light
away from
each other.
• Attach a filter
No on remote
control receiving section
of the indoor
unit.
Is there 2 VDC or less between CN10A (+)
and JPG (GND)(-) on the indoor electronic
control P.C. board?
No
Yes
Is there 2 VDC or less between
CN10A (+) and JPG (GND)(-) on
the indoor electronic control P.C.
board?
No
Yes
Replace the indoor power
P.C. board and the indoor
terminal P.C. board
37
Is there 2 VDC or less between
CN10A (+) and JPG (GND)(-) on
the indoor electronic control P.C.
board?
No
Replace the indoor electronic control P.C. board.
Yes
MSZ-GE60VA MSZ-GE60VAD MSZ-GE71VA MSZ-GE71VAD
MSZ-GE80VA MSZ-GE80VA2 MSZ-GE80VAD
Turn OFF the power supply.
Is there rated voltage in the power supply?
Yes
Check the power supply.
No
Turn ON the power supply.
Is there rated voltage between outdoor terminal block S1 and S2?
Yes
No
Check the wiring.
Press EMERGENCY OPERATION switch once.
Does the upper lamp of OPERATION INDICATOR lamp light up? <Confirmation of the power
to the indoor unit>
Yes
Is serial signal error indicated 6 minutes
later?
Yes
A
Turn OFF the power supply.
Check once more if the indoor/outdoor
B connecting wire is not miswiring.
Short-circuit outdoor terminal block S2
and S3. 1
Turn ON the power supply.
No
No
Is there any miswiring,
poor contact, or wire
disconnection of the
indoor/outdoor connecting wire?
No
Yes
Correct them.
1. Miswiring may damage indoor electronic control P.C.
board during the operation.
Be sure to confirm the wiring is correct before the operation starts.
3. Be sure to check this within 3 minutes after turning ON.
After 3 minutes, LED blinks 6 times. Even when the
inverter P.C. board or the outdoor electronic control P.C.
board is normal, LED blinks 6 times after 3 minutes.
(Except for outdoor unit of multi system type)
Is the bus-bar voltage of the inverter P.C. board or the outdoor electronic control P.C. board normal?
(Refer to "TEST POINT DIAGRAM AND VOLTAGE" of the outdoor unit.)
No
Yes
Does the LED on the inverter P.C. board or the outdoor electronic control P.C.
board repeat "3.6-second-OFF and 0.8-second-ON quick blinking"? 3
Yes
No
(Lighted
or not
lighted)
Turn OFF the power supply.
Remove the short-circuit between outdoor terminal block S2 and S3.
Replace the indoor electronic control P.C. board.
A
• Turn OFF inverter-controlled lighting
equipment.
• Turn OFF the power supply and then
turn ON again.
• Press EMERGENCY OPERATION
switch.
Is serial signal
error indicated 6
minutes later?
Yes
B
• Reinstall
either the unit
or the light
away from
each other.
• Attach a filter
No on remote
control receiving section
of the indoor
unit.
OBH531E
38
Replace the inverter P.C. board or the outdoor
electronic control P.C. board. 2
2. Be careful of the residual voltage of smoothing
capacitor.
E Check of installation of the horizontal vane
Turn OFF the power supply.
Is the stopper of the horizontal vane
locked to the indoor unit correctly?
Yes
No
Re-lock the stopper of the horizontal vane to the indoor unit.
(Refer to 10-1.5.)
Turn ON the
power supply.
Are all lamps flashing?
Yes
To check the continuity of the interlock
switch (Fan), measure the resistance of
connector - connected to CN1R1 on
the indoor electronic control P.C. board.
Is there resistance 0 Ω?
Yes
No(
Turn OFF the power supply.
)
Replace the interlock switch (Fan).
Replace the indoor electronic
control P.C. board.
OBH531E
39
No
OK
F Electromagnetic noise enters into TV sets or radios
Is the unit earthed?
Yes
Is the distance between the antennas
and the indoor unit within 3 m, or is the
distance between the antennas and the
outdoor unit within 3 m?
No
Earth the unit.
No
Yes
Extend the distance between the antennas and
the indoor unit, and/or the antennas and the
outdoor unit.
Is the distance between the TV sets or
radios and the indoor unit within 1 m, or
is the distance between the TV sets or
radios and the outdoor unit within 3 m?
No
Yes
Extend the distance between the TV sets and/or
radios and the indoor unit, or the TV sets or
radios and the outdoor unit.
Are the antennas damaged?
Is the coaxial cable damaged?
Is there any poor contact in the antenna wiring?
No
Yes
Replace or repair the antenna.
Replace or repair the coaxial cable.
Yes
Extend the distance between the indoor/outdoor
connecting wire of the air conditioner and the wiring of the antennas.
Is the indoor/outdoor connecting wire
of the air conditioner and the wiring of
the antennas close?
No
Even if all of the above conditions are fulfilled, the electromagnetic noise may enter, depending on the electric field strength
or the installation condition (combination of specific conditions such as antennas or wiring).
Check the following before asking for service.
1. Devices affected by the electromagnetic noise
TV sets, radios (FM/AM broadcast, shortwave)
2. Channel, frequency, broadcast station affected by the electromagnetic noise
3. Channel, frequency, broadcast station unaffected by the electromagnetic noise
4. Layout of:
indoor/outdoor unit of the air conditioner, indoor/outdoor wiring, earth wire, antennas, wiring from antennas, receiver
5. Electric field intensity of the broadcast station affected by the electromagnetic noise
6. Presence or absence of amplifier such as booster
7. Operation condition of air conditioner when the electromagnetic noise enters in
1) Turn OFF the power supply once, and then turn ON the power supply. In this situation, check for the electromagnetic
noise.
2) Within 3 minutes after turning ON the power supply, press OPERATE/STOP (ON/OFF) button on the remote controller
for power ON, and check for the electromagnetic noise.
3) After a short time (3 minutes later after turning ON), the outdoor unit starts running. During operation, check for the
electromagnetic noise.
4) Press OPERATE/STOP (ON/OFF) button on the remote controller for power OFF, when the outdoor unit stops but the
indoor/outdoor communication still runs on. In this situation, check for the electromagnetic noise.
OBH531E
40
10-7. TEST POINT DIAGRAM AND VOLTAGE
1. Indoor power P.C. board, Indoor terminal P.C. board
MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD
Indoor terminal P.C. board
Fuse (F11)( )
Indoor power P.C. board
Varistor (NR11)
Resistor (R111)
Indoor fan motor
(CN211)
325 VDC
(–) GND (highvoltage DC)
15 VDC
(+)3-6 VDC
(+)0 or 15 VDC
Terminal
block
Connector to indoor electronic
control P.C. board (CN20A)
5 VDC
12 VDC
GND
Please replace the fuse after removing the indoor terminal P.C. board from the electrical box.
MSZ-GE42VA MSZ-GE42VAD MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
Indoor terminal P.C. board
Fuse (F11)( )
Indoor power P.C. board
Varistor (NR11)
Reactor (L111)
Indoor fan motor
(CN211)
325 VDC
(–) GND (highvoltage DC)
15 VDC
(+)3-6 VDC
(+)0 or 15 VDC
Terminal
block
Connector to indoor electronic
control P.C. board (CN20A)
5 VDC
12 VDC
GND
Please replace the fuse after removing the indoor terminal P.C. board from the electrical box.
OBH531E
41
2. Indoor electronic control P.C. board
MSZ-GE22VA MSZ-GE25VA
MSZ-GE42VA MSZ-GE50VA
MSZ-GE33VA MSZ-GE35VA
MSZ-GE50VA2
MSZ-GE35VA2
Indoor electronic control P.C. board
Timer short mode point
JPG JPS (Refer to 8-1.)
Room temperature thermistor RT11 (CN111)
Indoor coil thermistor RT12, RT13 (CN112)
GND
Interlock switch (FAN) (CN1R1)
Vane motor (CN151)
Connector to
Indoor power P.C. board
(CN10A)
12 VDC
Emergency operation
switch (E.O. SW) (SW1)
5 VDC
To disable "Auto restart function",
solder the Jumper wire to JR07.
(Refer to 8-3.)
MSZ-GE22VAD MSZ-GE25VAD MSZ-GE35VAD MSZ-GE42VAD MSZ-GE50VAD
Timer short mode point
JPG JPS
(Refer to 8-1.)
Room temperature thermistor RT11 (CN111)
Indoor coil thermistor RT12 (CN112)
GND
Interlock switch (FAN)
(CN1R1)
Room temperature thermistor (RT11)
Indoor coil thermistor (RT12, RT13)
Connector to Indoor power
P.C. board (CN10A)
12 VDC
Resistance (kΩ)
Vane motor (CN151)
5 VDC
Emergency operation
switch (E.O. SW) (SW1)
OBH531E
To disable "Auto restart function",
solder the Jumper wire to JR07.
(Refer to 8-3.)
Temperature (°C)
42
3. Indoor electronic control P.C. board, Indoor terminal P.C. board, Power monitor receiver SW P.C. board
MSZ-GE60VA MSZ-GE71VA MSZ-GE80VA MSZ-GE80VA2
Indoor terminal P.C. board
Fuse
Terminal
(F11)( ) block
Varistor
(NR11)
Indoor electronic control P.C. board
To disable "Auto restart function",
Indoor coil thermistor
solder the Jumper wire to JR07. Interlock switch Resistor
RT12, RT13
12 VDC (Refer to 8-3.)
(FAN) (CN1R1) (R111)
(CN112)
Room temperature
thermistor RT11
(CN111)
JR24
JRRE
JRDFT
JR07
JRPRH
JR19
JRTU
JR01
Vane motor
(CN151, CN152)
Power monitor receiver SW P.C. board
CN20A
(–)
(+)
(Refer to 10-6.
.)
Indoor fan motor
(CN211)
325 VDC
(–) GND
(high-voltage DC)
15 VDC
(+)3-6 VDC
(+)0 or 15 VDC
5 VDC
Emergency
operation switch
(E.O. SW)
(SW1)
Timer short mode point
JPG JPS (Refer to 8-1.)
Please replace the fuse after removing the indoor terminal P.C. board from the electrical box.
Resistance (kΩ)
Room temperature thermistor (RT11)
Indoor coil thermistor (RT12, RT13)
Temperature (°C)
OBH531E
43
MSZ-GE60VAD MSZ-GE71VAD MSZ-GE80VAD
Indoor terminal P.C. board
Fuse
Terminal
(F11)( ) block
Varistor
(NR11)
Indoor electronic control P.C. board
To disable "Auto restart function",
Indoor coil thermistor
cut the Jumper wire to JR77.
Interlock switch Resistor
RT12, RT13
12 VDC (Refer to 8-3.)
(FAN) (CN1R1) (R111)
(CN112)
Room temperature
thermistor RT11
(CN111)
JR07
JR77
Vane motor
(CN151, CN152)
Power monitor receiver SW P.C. board
CN20A
(–)
(+)
(Refer to 10-6.
.)
Indoor fan motor
(CN211)
325 VDC
(–) GND
(high-voltage DC)
15 VDC
(+)3-6 VDC
(+)0 or 15 VDC
5 VDC
Emergency
operation switch
(E.O. SW)
(SW1)
Timer short mode point
JPG JPS (Refer to 8-1.)
Please replace the fuse after removing the indoor terminal P.C. board from the electrical box.
Resistance (kΩ)
Room temperature thermistor (RT11)
Indoor coil thermistor (RT12, RT13)
Temperature (°C)
OBH531E
44
11
DISASSEMBLY INSTRUCTIONS
<"Terminal with locking mechanism" Detaching points>
The terminal which has the locking mechanism can be detached as shown below.
There are two types (Refer to (1) and (2)) of the terminal with locking mechanism.
The terminal without locking mechanism can be detached by pulling it out.
Check the shape of the terminal before detaching.
(1) Slide the sleeve and check if there is a locking lever or not.
Sleeve
Locking lever
(2) The terminal with this connector has the
locking mechanism.
Slide the sleeve.
Pull the terminal while
pushing the locking
lever.
Hold the sleeve, and
pull out the terminal
slowly.
Connector
11-1. MSZ-GE22VA MSZ-GE22VAD MSZ-GE25VA MSZ-GE25VAD MSZ-GE33VA
MSZ-GE35VA MSZ-GE35VA2 MSZ-GE35VAD MSZ-GE42VA MSZ-GE42VAD
MSZ-GE50VA MSZ-GE50VA2 MSZ-GE50VAD
NOTE: Turn OFF power supply before disassembly.
OPERATING PROCEDURE
PHOTOS
1. Removing the panel
Photo 1
(1) Remove the horizontal vanes.
(2) Remove the screw caps of the panel. Remove the
screws of the panel.
(3) Unhook the lower part ( ) of the panel.
(4) Hold the lower part of both ends of the panel and pull
it slightly toward you, and then remove the panel by
pushing it upward.
Horizontal vanes
Front panel
A
Screws of the panel
OBH531E
45
OPERATING PROCEDURE
2. Removing the indoor electronic control P.C.
board and the room temperature thermistor
(1) Remove the panel (Refer to 1.) and the corner box.
(2) Remove the screw of the V.A. clamp. Remove the V.A.
clamp and the indoor/outdoor connecting wire.
(3) Open the indoor electronic control P.C. board holder (to
right side)
(4) Disconnect the following connectors:
<Indoor electronic control P.C. board>
CN112 (Indoor coil thermistor)
CN151 (Vane motor)
CN1R1 (Interlock switch)
CN10A (To the indoor power P.C. board)
(5) Unhook the catches of the indoor electronic control P.C.
board holder from the nozzle and the electrical box
(right side).
(6) Remove the room temperature thermistor from the
hook of the indoor electronic control P.C. board holder.
(7) Open the back side of the indoor electronic control P.C.
board holder, and remove the indoor electronic control P.C. board.
(8) Remove the room temperature thermistor from the
indoor electronic control P.C. board.
PHOTOS
Photo 2
Earth wire
Electrical box
Screw of the
electrical cover
V.A. clamp
Catch of indoor electronic
control P.C. board holder
Indoor electronic control
P.C. board holder
Photo 3
Upper catch
Indoor terminal
P.C. board
Indoor power
P.C. board
3. Remove the indoor power P.C. board, the indoor
terminal P.C. board, and the electrical box
(1) Remove the panel (Refer to 1.) and the corner box.
(2) Remove the indoor/outdoor connecting wire. (Refer to 2.)
(3) Remove the earth wire connected to the indoor heat
exchanger from the electrical box.
(4) Unhook first the lower, then the upper catches of the
electrical box, and pull out the electrical box.
(5) Remove the screw of the electrical cover and remove
the electrical cover.
(6) Disconnect all the connectors on the indoor power P.C.
board and unhook all lead wires.
(7) Remove the screw of terminal block on the indoor terminal P.C. board.
(8) Remove the indoor power P.C. board and the indoor
terminal P.C. board.
OBH531E
Terminal block
Lower catch
Catch of indoor electronic control P.C.
board holder
46
OPERATING PROCEDURE
PHOTOS
4. Removing the nozzle assembly
Photo 4
(1) Remove the panel (Refer to 1.) and the corner box.
(2) Remove the indoor/outdoor connecting wire. (Refer to 2.)
(3) Remove the indoor electronic control P.C. board holder
(4) Disconnect the following connectors:
<Indoor electronic control P.C. board>
CN1R1 (Interlock switch)
(5) Pull out the drain hose from the nozzle assembly and
remove the nozzle assembly.
(6) Remove the interlock switch.
Interlock switch
5. Removing the horizontal vane motor
(1) Remove the nozzle assembly. (Refer to 4.)
(2) Remove the screws of the horizontal vane motor unit.
(3) Disconnect the connector from the horizontal vane
motor.
(4) Remove the screws of the horizontal vane motor.
(5) Remove the horizontal vane motor from the horizontal
vane motor unit.
OBH531E
Screws of the interlock switch
Photo 5
Screws of horizontal vane motor unit
47
OPERATING PROCEDURE
PHOTOS
Photo 6
6. Removing the indoor fan motor, the indoor coil
thermistor, and the line flow fan
(1) Remove the panel (Refer to 1.) and the corner box.
(2) Remove the indoor electronic control P.C. board holder, the electrical box and the nozzle assembly.
(3) Remove the screws fixing the motor bed.
(4) Loosen the screw fixing the line flow fan.
(5) Remove the motor bed together with fan motor and
motor band.
(6) Release the hooks of the motor band. Remove the
motor band. Pull out the indoor fan motor.
(8) Remove the indoor coil thermistor from the heat
exchanger.
( ) Install the indoor coil thermistor in its former position
when assembling it. (Photo 9)
(9) Remove the screws fixing the left side of the heat
exchanger.
(10) Lift the heat exchanger, and pull out the line flow fan
to the lower-left.
Screw of the line flow fan
Photo 7
Motor band
Photo 9
Screws of the
motor bed
Indoor coil
thermistor (sub)
RT13
Indoor coil
thermistor (main)
RT12
Photo 8
Screws of the
left side of the
heat exchanger
OBH531E
48
11-2. MSZ-GE60VA MSZ-GE60VAD MSZ-GE71VA MSZ-GE71VAD
MSZ-GE80VA MSZ-GE80VA2 MSZ-GE80VAD
NOTE: Turn OFF power supply before disassembly.
OPERATING PROCEDURE
PHOTOS
1. Removing the panel
Photo 1
(1) Remove the horizontal vanes.
(2) Remove the screw caps of the panel. Remove the
screws of the panel.
(3) Hold the lower part of both ends of the panel and pull
it slightly toward you, and then remove the panel by
pushing it upward.
Horizontal vanes
Front panel
Screws of the panel
OBH531E
49
OPERATING PROCEDURE
PHOTOS
2. Removing the indoor electronic control P.C.
board, the power monitor receiver SW P.C.
board and the indoor terminal P.C. board
Photo 2
(1) Remove the panel (Refer to 1.) and the corner box.
(2) Remove the screw of the V.A. clamp.
Remove the V.A. clamp and the indoor/outdoor connecting wire.
(3) Remove the screw of the electrical cover, and then
the electrical cover.
(4) Remove the earth wire connected to the indoor electronic control P.C. board from the electrical box.
(5) Remove the power monitor receiver holder.
(6) Open the rear cover of the power monitor receiver
holder and pull out the power monitor receiver SW P.C.
board.
(7) Disconnect all the connectors on the indoor electronic
control P.C. board and unhook all lead wires.
(8) Remove the screw of the terminal block on the indoor
terminal P.C. board.
(9) Remove the indoor terminal P.C. board and the indoor
electronic control P.C. board.
Electrical box
Screw of the
electrical cover
Screw of the
V.A. clamp
Power monitor
receiver holder
Photo 3
Upper catch
Indoor electronic control P.C.
board
Indoor terminal
P.C. board
3. Removing the indoor electrical box
(1) Remove the panel (Refer to 1.) and the corner box.
(2) Remove the indoor/outdoor connecting wire. (Refer to 2.)
(3) Remove the earth wire connected to the indoor heat
exchanger from the electrical box.
(4) Remove the screw of the electrical cover and remove
the electrical cover.
(5) Disconnect all the connectors on the indoor electronic
control P.C. board and unhook all lead wires.
(6) Remove the screw fixing the electrical box, then the
upper catch of the electrical box, and pull out the
electrical box.
Screw of the
terminal block
Screw of the
electrical box
Earth wires
OBH531E
50
OPERATING PROCEDURE
PHOTOS
4. Removing the nozzle assembly
Photo 4
(1) Remove the panel (Refer to 1.) and the corner box.
(2) Remove the V.A. clamp, and then the indoor/outdoor
connecting wire. (Photo 2)
(3) Remove the electrical cover. (Photo 2)
(4) Disconnect the following connectors on the electronic
control P.C. board:
CN151 (Horizontal vane motor)
CN152 (Vertical vane motor)
CN1R1 (Interlock switch)
(5) Remove the power monitor receiver holder. (Photo 2)
(6) Pull out the drain hose from the nozzle assembly and
remove the nozzle assembly.
(7) Remove the vane motors. (Refer to 5 and 6.)
(8) Remove the interlock switch.
Screws of the interlock switch
Screw of
the vertical vane
motor unit
5. Removing the vertical vane motor unit
Photo 5
(1) Remove the nozzle assembly. (Refer to 4.)
(2) Remove the crank of the vertical vane motor unit from
the arm of the vertical vane.
(3) Remove the screw of the vertical vane motor unit, and
pull the vertical vane motor unit.
(4) Remove the screws of the vertical vane motor unit
cover.
(5) Remove the crank of the vertical vane motor unit from
the shaft of the vane motor.
(6) Remove the vertical vane motor from the vertical vane
motor unit.
(7) Disconnect the connector of vertical vane motor from
the vertical vane motor.
Screws of
the vertical
vane motor
unit cover
6. Removing the horizontal vane motor
(1) Remove the nozzle assembly. (Refer to 4.)
(2) Remove the screws of the horizontal vane motor unit,
and pull out the horizontal vane motor unit.
(3) Disconnect the connector from the horizontal vane
motor.
(4) Remove the screws of the horizontal vane motor unit
cover.
(5) Remove the horizontal vane motor from the horizontal
vane motor unit.
Photo 6
Screws of
the horizontal vane
motor unit
OBH531E
51
Screws of
the horizontal
vane motor
unit cover
OPERATING PROCEDURE
PHOTOS
7. Removing the water cut, the indoor fan motor,
the indoor coil thermistor, and the line flow fan
Photo 8
(1) Remove the panel (Refer to 1.) and the corner box.
(2) Remove the power monitor receiver holder, the electrical box and the nozzle assembly. (Refer to 3 and 4.)
(3) Remove the screw of the water cut and remove the
water cut.
(4) Remove the screws fixing the motor bed.
(5) Loosen the screw fixing the line flow fan.
(6) Remove the motor bed together with fan motor and
motor band.
(7) Remove the screw of the motor band.
(8) Release the hooks of the motor band. Remove the
motor band. Pull out the indoor fan motor.
(9) Remove the indoor coil thermistor from the heat
exchanger.
Install the indoor coil thermistor in its former position
when assembling it. (Photo 9)
(10) Remove the screws fixing the left side of the heat
exchanger.
(11) Lift the heat exchanger, and pull out the line flow fan
to the lower-left.
Screw of the line flow fan
Photo 9
Indoor coil thermistor (main) RT12
Motor band
Photo 7
Electrical box
Screw of the
motor band
Screw of the
electrical cover
Screws of the
motor bed
Indoor coil thermistor (sub) RT13
Screw of the
V.A. clamp
Screw of the
water cut
Photo 10
Power monitor
receiver holder
Screws of the
heat exchanger
OBH531E
52
OBH531E
53
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
© Copyright 2009 MITSUBISHI ELECTRIC CORPORATION
Distributed in Dec. 2013. No. OBH531 REVISED EDITION-E
Distributed in Sep. 2013. No. OBH531 REVISED EDITION-D
Distributed in Jul. 2011. No. OBH531 REVISED EDITION-C
Distributed in Jul. 2010. No. OBH531 REVISED EDITION-B 5
Distributed in Oct. 2009. No. OBH531 REVISED EDITION-A 5
Distributed in Feb. 2009. No. OBH531 5
Made in Japan
New publication, effective Dec. 2013
Specifications are subject to change without notice.
Download PDF