Eaton | Powerware 5130 Rack/Tower UPS 1250-3000 VA | User`s guide | Eaton Powerware 5130 Rack/Tower UPS 1250-3000 VA User`s guide

Powerware® 5130 Rack/Tower UPS
1250–3000 VA
User’s Guide
Requesting a Declaration of Conformity
Units that are labeled with a CE mark comply with the following harmonized standards and EU directives:
S
Harmonized Standards: EN 62040-1-1 and EN 62040-2; IEC 60950-1
S
EU Directives:
73/23/EEC, Council Directive on equipment designed for use within certain voltage limits
93/68/EEC, Amending Directive 73/23/EEC
2004/108/EEC, Council Directive relating to electromagnetic compatibility
The EC Declaration of Conformity is available upon request for products with a CE mark. For copies of the EC
Declaration of Conformity, contact:
Eaton Power Quality Oy
Koskelontie 13
FIN-02920 Espoo
Finland
Phone: +358-9-452 661
Fax: +358-9-452 665 68
Eaton, Powerware, FERRUPS, and LanSafe re registered trademarks of Eaton Corporation or its subsidiaries and
affiliates. National Electrical Code and NEC are registered trademarks of National Fire Protection Association, Inc.
Phillips is a registered trademark of Phillips Screw Company. All other trademarks are property of their respective
companies.
ECopyright 2008 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
Class A EMC Statements
(Low-Voltage Models)
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
EN 62040-2
Some configurations are classified under EN 62040-2 as “Category C2 UPS.” For these configurations, the
following applies:
WARNING This is a category C2 UPS product. In a residential environment, this product may cause radio
interference, in which case the user may be required to take additional measures.
Class B EMC Statements
(High-Voltage Models)
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
S
Reorient or relocate the receiving antenna.
S
Increase the separation between the equipment and the receiver.
S
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
S
Consult the dealer or an experienced radio/TV technician for help.
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock
symbol.
CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’s manual for additional
information, such as important operating and maintenance instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries in the trash. This
product contains sealed, lead-acid batteries and must be disposed of properly. For more information,
contact your local recycling/reuse or hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE) in
the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.
Table of Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
Inspecting the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking the Accessory Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the UPS Internal Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rackmount Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Rail Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tower Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RPO and ROO Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Rear Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
20
22
23
23
23
24
25
28
31
33
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
Turning the UPS On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting the UPS on Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turning the UPS Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
36
36
37
37
38
38
Additional UPS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact Communication Port (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load Segments (PowerShare) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Customizing the UPS with the UPS Configuration Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
41
42
43
UPS Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
UPS and Battery Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transporting the UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storing the UPS and Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When to Replace Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
45
46
46
4
5
6
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
i
TABLE OF CONTENTS
Replacing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Replace Internal Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Replace Extended Battery Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recycling the Used Battery or UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
47
49
50
7
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
8
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
57
Audible Alarms and UPS Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
57
59
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
Two-Year Limited Warranty (US and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ten-Year Pro-Rated Limited Warranty (US and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load Protection Guarantee (US and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
63
65
9
ii
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
Introduction
Eaton’s Powerware® 5130 uninterruptible power system (UPS) protects
your sensitive electronic equipment from basic power problems such as
power failures, power sags, power surges, brownouts, and line noise.
Power outages can occur when you least expect it and power
quality can be erratic. These power problems have the potential to
corrupt critical data, destroy unsaved work sessions, and damage
hardware — causing hours of lost productivity and expensive repairs.
With the Powerware 5130, you can safely eliminate the effects of power
disturbances and guard the integrity of your equipment. The Powerware
5130 was designed for critical applications such as PCs, servers,
workstations, and telecommunications equipment.
2
Figure 1 shows the Powerware 5130 UPS with an optional Extended
Battery Module (EBM).
1
Chapter 1
Figure 1. Powerware 5130 UPS with Optional EBM
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
1
INTRODUCTION
Providing outstanding performance and reliability, the Powerware 5130’s
unique benefits include:
S Hours of extended runtime with up to four EBMs.
S Start-on-battery capability for powering up the UPS even if utility
power is not available.
S Hot-swappable batteries that simplify maintenance by allowing you to
replace batteries safely without powering down the critical load.
S Shutdown control through the remote power-off (RPO) and remote
on/off (ROO) port.
S Two standard communication options with a USB port and an RS-232
serial port.
S Advanced power management for graceful shutdowns and power
monitoring.
S Sequential shutdown and load management through separate
receptacle groups, called load segments (PowerShare).
S Optional communication cards with enhanced communication
capabilities for increased power protection and control.
S Backed by worldwide agency approvals.
2
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
Chapter 2
Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
maintenance of the UPS and batteries. Please read all instructions before operating the
equipment and save this manual for future reference.
DANGER
This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by
AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS
inside the UPS.
WARNING
S This UPS contains its own energy source (batteries). The output receptacles may carry
live voltage even when the UPS is not connected to an AC supply.
S For 230V models, the output receptacles may remain electrically live. If the input power
source in your application is wired line-to-neutral (as in most European applications), the
voltage to the output receptacles is 0V. With line-to-line input wiring, the voltage to the
output receptacles is 115V (measured from line-to-ground or line-to-neutral, depending
on the UPS wiring).
S Do not remove or unplug the input cord when the UPS is turned on. This removes the
safety ground from the UPS and the equipment connected to the UPS.
S To reduce the risk of fire or electric shock, install this UPS in a temperature and humidity
controlled, indoor environment, free of conductive contaminants. Ambient temperature
must not exceed 40°C (104°F). Do not operate near water or excessive humidity (95%
maximum).
S To comply with international standards and wiring regulations, the total equipment
connected to the output of this UPS must not have an earth leakage current greater than
3.5 milliamperes.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
3
SAFETY WARNINGS
CAUTION
S Batteries can present a risk of electrical shock or burn from high short-circuit current.
Observe proper precautions. Servicing should be performed by qualified service
personnel knowledgeable of batteries and required precautions. Keep unauthorized
personnel away from batteries.
S Proper disposal of batteries is required. Refer to your local codes for disposal
requirements.
S Never dispose of batteries in a fire. Batteries may explode when exposed to flame.
Sikkerhedsanvisninger
VIGTIGE SIKKERHEDSANVISNINGER
GEM DISSE ANVISNINGER
Denne manual indeholder vigtige instruktioner, som skal følges under installation og
vedligeholdelse af UPS’en og batterierne. Læs venligst alle instruktioner inden betjening af
udstyret og gem denne manual mhp. fremtidige opslag.
FARE
Denne UPS indeholder LIVSFARLIG HØJSPÆNDING. Alle reparationer og vedligeholdelse bør
kun udføres af en AUTORISERET SERVICETEKNIKER. Ingen af UPS’ens indvendige dele kan
repareres af brugeren.
ADVARSEL!
S Denne UPS indeholder sin egen energikilde (batterier). Udgangsstikkene kan endog være
strømførende, når UPS’en ikke er koblet til en vekselstrømsforsyning.
S På 230V-modeller kan udgangsstikkene være strømførende. Hvis ledningsføringen til
indgangsstrømkilden på din enhed er fase-til-neutral (som på de fleste europæiske
enheder), er spændingen til udgangsstikkene 0V. Med en fase-til-fase
indgangsledningsføring er spændingen til udgangsstikkene 115V (målt fra fase-til-jord
eller fase-til-neutral, afhængig af UPS-ledningsføringen).
S Netledningen må ikke fjernes og stikket må ikke trækkes ud, mens UPS’en er tændt.
Dette fjerner sikkerhedsjorden fra UPS’en og fra det udstyr, der er sat til.
S Installér denne UPS i et temperatur- og fugtighedskontrolleret indendørsmiljø, frit for
ledende forureningsstoffer for at formindske risikoen for brand og elektrisk stød.
Rumtemperaturen må ikke overstige 40°C. UPS’en bør ikke betjenes nær vand eller høj
fugtighed (maksimalt 95%).
S I overensstemmelse med internationale normer og bestemmelser for el-installation må
det udstyr, der er forbundet til udgangen af denne UPS, tilsammen ikke overskride en
jordafdelingsspænding på mere end 3,5 milliampere.
4
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
SAFETY WARNINGS
ADVARSEL
S Batterierne kan give risiko for elektrisk stød eller brandsår forårsaget af høj
kortslutningsstrøm. Overhold gældende forsigtighedsregler. Servicering skal udføres af
kvalificeret servicepersonale med kendskab til batterier og gældende forsigtighedsregler.
Hold uautoriseret personale væk fra batterierne.
S Korrekt bortskaffelse af batterier er påkrævet. Overhold gældende lokale regler for
bortskaffelsesprocedurer.
S Skaf dig aldrig af med batterierne ved at brænde dem. Batterierne kan eksplodere ved
åben ild.
Belangrijke Veiligheidsinstructies
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
BEWAAR DEZE INSTRUCTIES
Deze handleiding bevat belangrijke instructies die u dient te volgen tijdens de installatie en
het onderhoud van de UPS en de accu’s. Lees alle instructies voordat u de apparatuur in
bedrijf neemt en bewaar deze handleiding als naslagwerk.
GEVAAR
Deze UPS bevat LEVENSGEVAARLIJKE ELEKTRISCHE SPANNING. Alle reparaties en
onderhoud dienen UITSLUITEND DOOR ERKEND SERVICEPERSONEEL te worden uitgevoerd.
Er bevinden zich GEEN ONDERDELEN in de UPS die DOOR DE GEBRUIKER kunnen worden
GEREPAREERD.
WAARSCHUWING
S Deze UPS bevat een eigen energiebron (batterijen). De uitgangscontactdoos kan onder
spanning staan, zelfs wanneer de UPS niet is aangesloten op de netspanning.
S Bij de modellen van 230V kan de uitgangscontactdoos onder spanning blijven staan. Als
de bedrading van de ingangsspanningsbron in uw systeem loopt van fase naar aarde
(zoals bij de meeste Europese systemen) dan bedraagt de spanning op de
uitgangscontactdozen 0 V. Als de ingangsbedrading loopt van fase naar fase dan
bedraagt de spanning op de uitgangscontactdozen 115V (gemeten tussen fase en aarde
of tussen fase en neutraal, afhankelijk van de UPS-bedrading).
S Verwijder de ingangsnoer niet of haal de stekker van de ingangsnoer er niet uit terwijl de
UPS aan staat. Hierdoor zou de UPS en uw aangesloten apparatuur geen
aardebeveiliging meer hebben.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
5
SAFETY WARNINGS
S Teneinde de kans op brand of elektrische schok te verminderen dient deze UPS in een
gebouw met temperatuur- en vochtigheidregeling te worden geïnstalleerd, waar geen
geleidende verontreinigingen aanwezig zijn. De omgevingstemperatuur mag 40°C niet
overschrijden. Niet gebruiken in de buurt van water of bij zeer hoge vochtigheid
(max. 95%).
S Om aan de internationale normen en bedradingsvoorschriften te voldoen mag de gehele
apparatuur die op de uitgang van deze UPS is aangesloten, geen aardlekstroom van
meer dan 3,5 milliampère hebben.
OPGELET
S Batterijen leveren gevaar op voor elektrische schokken en kunnen brandwonden
veroorzaken door een grote kortsluitstroom. Neem de juiste voorzorgsmaatregelen in
acht. Het onderhoud moet worden uitgevoerd door bevoegde onderhoudsmonteurs die
verstand hebben van accu’s en op de hoogte zijn van de vereiste voorzorgsmaatregelen.
Houd onbevoegden uit de buurt van de accu’s.
S De batterijen moeten op de juiste wijze worden opgeruimd. Raadpleeg hiervoor uw
plaatselijke voorschriften.
S Nooit batterijen in het vuur gooien. De batterijen kunnen ontploffen.
6
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
SAFETY WARNINGS
Tarkeita Turvaohjeita
TÄRKEITÄ TURVAOHJEITA - SUOMI
SÄILYTÄ NÄMÄ OHJEET
Tämä käyttöohje sisältää tärkeitä ohjeita, joita on noudatettava UPS-virtalähteen ja akkujen
asennuksen ja huollon yhteydessä. Lue kaikki ohjeet ennen laitteiston käyttöä ja säilytä ohje
myöhempää tarvetta varten.
VAARA
Tämä UPS sisältää HENGENVAARALLISIA JÄNNITTEITÄ. Kaikki korjaukset ja huollot on
jätettävä VAIN VALTUUTETUN HUOLTOHENKILÖN TOIMEKSI. UPS ei sisällä MITÄÄN
KÄYTTÄJÄN HUOLLETTAVIA OSIA.
VAROITUS
S Tässä UPS-virtalähteessä on oma energianlähde (akut). Lähtövastakkeissa voi olla
jännite, vaikka UPS-virtalähdettä ei ole kytketty verkkovirtaan.
S 230V -malleissa lähtövastakkeissa voi säilyä jännite. Jos sovelluksen tulovirtalähde on
johdotettu linjasta neutraaliin (kuten useimmissa eurooppalaisissa sovelluksissa)
lähtövastakkeiden jännite on 0 V. Linjasta linjaan –tulojohdotuksessa lähtövastakkeiden
jännite on 115V (mitataan linjasta maahan tai linjasta neutraaliin, UPS-virtalähteen
johdotuksesta riippuen).
S Älä poista tai irrota sisääntulojohtoa, kun UPS on kytkettynä. Tämä poistaa
turvamaadoituksen UPS-laitteesta ja siihen liitetystä laitteistosta.
S Vähentääksesi tulipalon ja sähköiskun vaaraa asenna tämä UPS sisätiloihin,
joissa lämpötila ja kosteus on säädettävissä ja joissa ei ole virtaa johtavia
epäpuhtauksia. Ympäristön lämpötila ei saa ylittää 40 °C. Älä käytä lähellä vettä ja vältä
kosteita tiloja (95 % maksimi).
S Kansainväliset normit ja johdotusmääräykset vaativat, että kaikkien tämän UPS-laitteen
ulostulokytkentöjen yhteinen maavuotovirta ei ylitä 3,5 milliampeeria (mA).
VARO
S Akut voivat aiheuttaa sähköiskun tai palovammojen vaaran johtuen suuresta
oikosulkuvirrasta. Noudata kaikkia asianmukaisia varotoimia. Laitteen saa huoltaa vain
ammattitaitoinen huoltohenkilökunta, joka tuntee akut ja niihin liittyvät varotoimet. Älä
päästä valtuuttamatonta henkilöstöä lähelle akkuja.
S Akusto täytyy hävittää säädösten mukaisella tavalla. Noudata paikallisia määräyksiä.
S Älä koskaan heitä akkuja tuleen. Ne voivat räjähtää.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
7
SAFETY WARNINGS
Consignes de sécurité
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute
procédure d’installation et de maintenance des batteries et de l’onduleur. Veuillez consulter
entièrement ces instructions avant de faire fonctionner l’équipement et conserver ce manuel
afin de pouvoir vous y reporter ultérieurement.
DANGER!
Cet onduleur contient des TENSIONS MORTELLES. Toute opération d’entretien et de
réparation doit être EXCLUSIVEMENT CONFIÉE A UN PERSONNEL QUALIFIÉ AGRÉÉ.
AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR ne se trouve dans l’onduleur.
AVERTISSEMENT!
S Cette onduleur possède sa propre source d’alimentation (batteries). Il est possible que
les prises de sortie soient sous tension même lorsque l’onduleur n’est pas connectée à
une alimentation CA.
S En ce qui concerne les modèles 230 V, il est possible que les prises de sortie restent
sous tension. Si la source d’alimentation de votre application est câblée phase et neutre
(comme dans la majorité des applications européennes), la tension vers les prises de
sortie est de 0 V. Avec un câblage d’entrée phase à phase, la tension vers les prises de
sortie est de 115 V (mesurée entre phase et terre ou phase et neutre suivant le câblage
de l’onduleur).
S Ne pas retirer le cordon d’alimentation lorsque l’onduleur est sous tension sous peine de
supprimer la mise à la terre de l’onduleur et du matériel connecté.
S Pour réduire les risques d’incendie et de décharge électrique, installer l’onduleur
uniquement à l’intérieur, dans un lieu dépourvu de matériaux conducteurs, où la
température et l’humidité ambiantes sont contrôlées. La température ambiante ne doit
pas dépasser 40 °C. Ne pas utiliser à proximité d’eau ou dans une atmosphère
excessivement humide (95 % maximum).
S Afin d’être conforme aux normes et règlements internationaux de câblage, le courant de
fuite à la terre de la totalité du matériel branché sur la sortie de l’onduleur ne doit pas
dépasser 3,5 mA.
8
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
SAFETY WARNINGS
ATTENTION!
S Les batteries peuvent présenter un risque de choc électrique ou de brûlure provenant
d’un courant de court-circuit haute intensité. Observez les précautions appropriées.
L’entretien doit être réalisé par du personnel qualifié connaissant bien les batteries et
les précautions nécessaires. N’autorisez aucun personnel non qualifié à manipuler les
batteries.
S Une mise au rebut réglementaire des batteries est obligatoire. Consulter les règlements
en vigueur dans votre localité.
S Ne jamais jeter les batteries au feu. L’exposition aux flammes risque de les faire
exploser.
Sicherheitswarnungen
WICHTIGE SICHERHEITSANWEISUNGEN
AUFBEWAREN
Dieses Handbuch enthält wichtige Anweisungen, die Sie während der Installation und
Wartung des USV (Unterbrechungsfreies Stromversorgungssystem) und der Batterien
befolgen müssen. Bitte lesen Sie alle Anweisungen des Handbuches bevor sie mit dem
Gerät arbeiten. Bewaren Sie das Handbuch zum Nachlesen auf.
WARNUNG
Die USV führt lebensgefährliche Spannungen. Alle Reparatur- und Wartungsarbeiten sollten
nur von Kundendienstfachleuten durchgeführt werden. Die USV enthält keine vom Benutzer
zu wartenden Komponenten.
ACHTUNG
S Dieses USV (Unterbrechungsfreies Stromversorgungssystem) enthält eine eigene
Energiequelle (Batterien). Die Ausgangssteckdosen können Spannung führen, auch wenn
das USV nicht an eine Wechselstromquelle angeschlossen ist.
S Bei Modellen mit 230 Volt können die Ausgangssteckverbinder stromführend bleiben.
Wenn die Eingangsstromquelle in Ihrer Anlage mit Masseleitung verkabelt ist (wie in
den meisten europäischen Anlagen), beträgt die Spannung an den
Ausgangssteckverbindern 0 Volt. Bei einer Verkabelung mit Außenleitern beträgt die
Spannung an den Ausgangssteckverbindern 115 Volt (gemessen von Leitung zu Masse
oder Leitung zu Masseleiter, abhängig von der USV-Verkabelung.
S Das Eingangskabel nicht entfernen oder abziehen, während die USV eingeschaltet ist,
weil hierdurch die Sicherheitserdung von der USV und den daran angeschlossenen
Geräten entfernt wird.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
9
SAFETY WARNINGS
S Um die Brand- oder Elektroschockgefahr zu verringern, diese USV nur in Gebäuden mit
kontrollierter Temperatur und Luftfeuchtigkeit installieren, in denen keine leitenden
Schmutzstoffen vorhanden sind. Die Umgebungstemperatur darf 40°C nicht übersteigen.
Die USV nicht in der Nähe von Wasser oder in extrem hoher Luftfeuchtigkeit (max. 95 %)
betreiben.
S Um internationale Normen und Verdrahtungsvorschriften zu erfüllen, dürfen die an den
Ausgang dieser USV angeschlossenen Geräte zusammen einen Erdableitstrom von
insgesamt 3,5 Milliampere nicht überschreiten.
VORSICHT!
S Batterien können das Risiko eines elektrischen Schlags bergen oder durch hohen
Kurzschlussstrom in Brand geraten. Die richtigen Vorsichtsmaßnahmen beachten. Die
Wartung muss von qualifiziertem Wartungspersonal durchgeführt werden, das im
Umgang mit Batterien geübt ist und über gute Kenntnisse der erforderlichen
Vorsichtsmaßnahmen verfügt. Nicht autorisiertes Personal von Batterien fern halten.
S Die Batterien müssen ordnungsgemäß entsorgt werden. Hierbei sind die örtlichen
Bestimmungen zu beachten.
S Batterien niemals verbrennen, da sie explodieren können.
Avvisi di sicurezza
IMPORTANTI ISTRUZIONI DI SICUREZZA
CONSERVARE QUESTE ISTRUZIONI
Il presente manuale contiene importanti istruzioni da seguire durante l’installazione e la
manutenzione dell’UPS e delle batterie. Leggere integralmente le istruzioni prima di
utilizzare l’apparecchiatura e conservare il presente manuale per futuro riferimento.
PERICOLO
La TENSIONE contenuta in questo gruppo statico di continuità è LETALE. Tutte le operazioni
di riparazione e di manutenzione devono essere effettuate ESCLUSIVAMENTE DA
PERSONALE TECNICO AUTORIZZATO. All’interno del gruppo statico di continuità NON vi
sono PARTI RIPARABILI DALL’UTENTE.
10
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
SAFETY WARNINGS
AVVERTENZA
S L’UPS contiene la propria fonte di energia (batterie). Le prese d’uscita possono essere
sotto tensione anche quando l’UPS non è collegato all’alimentazione elettrica CA.
S Nei modelli da 230 V è possibile che le prese d’uscita rimangano sotto tensione. Se la
fonte di alimentazione in entrata dell’installazione è costituita da un collegamento
linea-neutro (come accade nella maggior parte delle installazioni europee), la tensione
delle prese d’uscita è pari a 0 V. Con un cablaggio in entrata del tipo linea-linea, la
tensione sulle prese d’uscita è 115 V (con misurazione effettuata da linea a terra o da
linea a neutro in base al cablaggio dell’UPS).
S Non rimuovere nè scollegare il cavo di ingresso quando il gruppo statico di continuità è
acceso poichè in tal modo si disattiverebbe il collegamento a terra di sicurezza del
gruppo statico di continuità e dell’apparecchiatura ad esso collegata.
S Per ridurre il rischio di incendio o di scossa elettrica, installare il gruppo statico di
continuità in un ambiente interno a temperatura ed umidità controllata, privo di agenti
contaminanti conduttivi. La temperatura ambiente non deve superare i 40°C. Non
utilizzare l’unità in prossimità di acqua o in presenza di umidità eccessiva (95% max).
S Per conformità con gli standard internazionali e con le norme in merito al cablaggio, tutta
l’apparecchiatura collegata con l’uscita del gruppo statico di continuità non deve avere
una corrente di dispersione di terra superiore a 3,5 milliampere.
ATTENZIONE
S Le batterie possono comportare un rischio di scossa elettrica o di ustione in seguito a
un’elevata corrente di corto circuito. Osservare le dovute precauzioni. L’assistenza deve
essere eseguita da personale qualificato esperto di batterie e delle necessarie
precauzioni. Tenere il personale non autorizzato lontano dalle batterie.
S Le batterie devono essere smaltite in modo corretto. Per i requisiti di smaltimento fare
riferimento alle disposizioni locali.
S Non gettare mai le batterie nel fuoco poichè potrebbero esplodere se esposte alle
fiamme.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
11
SAFETY WARNINGS
Viktig Sikkerhetsinformasion
VIKTIGE SIKKERHETSINSTRUKSJONER
GJEM DISSE INSTRUKSJONENE
Denne håndboken inneholder viktige instruksjoner som du bør overholde ved montering og
vedlikehold av UPS-enheten og batteriene. Les alle instruksjoner før utstyret tas i bruk, og
gjem håndboken til fremtidig referanse.
FARLIG
Denne UPS’en inneholder LIVSFARLIGE SPENNINGER. All reparasjon og service må kun
utføres av AUTORISERT SERVICEPERSONALE. BRUKERE KAN IKKE UTFØRE SERVICE PÅ
NOEN AV DELENE i UPS’en.
FARLIG
S UPS-enheten inneholder sin egen energikilde (batterier). Utgangsstikkene kan være
strømførende selv når UPS-enheten ikke er koblet til et strømuttak.
S Utgangsstikkene kan være strømførende for 230V modellene. Spenningen til
utgangsstikkene vil være 0 V dersom din enhets strømkilde er fase-til-nøytral (som på de
fleste europeiske enheter). Med ledningsført fase-til-fase inngang vil spenningen til
utgangsstikkene være 115V (målt fra fase-til-jord eller fase-til-nøytral, avhenging av
UPS-ledningsføringen).
S Strømforsyningskabelen må ikke fjernes eller trekkes ut når UPS’en er på, slik at ikke
sikkerhetsjordingen fjernes fra UPS’en og det utstyret som er forbundet med den.
S For å redusere fare for brann eller elektriske støt, bør denne UPS’en installeres i et
innendørs miljø med kontrollert temperatur og luftfuktighet som er fritt for ledende,
forurensende stoffer. Romtemperaturen må ikke overskride 40°C. Den må ikke brukes i
nærheten av vann eller ved meget høy luftfuktighet (95% maks.).
S Alt utstyr som er forbundet med utgangen av denne UPS’en må ikke ha en sterkere total
lekkasjestrøm enn 3,5 milliampere for å være i overensstemmelse med internasjonale
standarder og forkablingsbestemmelser.
12
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
SAFETY WARNINGS
FORSIKTIG
S Batterier kan utgjøre en fare for elektrisk støt eller brannsår pga. høy kortsluttingsstrøm.
Treff passende forholdsregler. Service bør utføres av kvalifisert servicepersonale med
kjennskap til batterier og nødvendige forholdsregler. Hold uautorisert personale borte fra
batteriene.
S Batterier må fjernes på korrekt måte. Se lokale forskrifter vedrørende krav om fjerning av
batterier.
S Kast aldri batterier i flammer, da de kan eksplodere, hvis de utsettes for åpen ild.
Regulamentos de Segurança
INSTRUÇÕES DE SEGURANÇA IMPORTANTES
GUARDE ESTAS INSTRUÇÕES
Este manual contém instruções importantes que devem ser seguidas durante a instalação e
manutenção do no-break e das baterias. Leia todas as instruções antes de operar o
equipamento e guarde este manual para consultá-lo futuramente.
CUIDADO
A UPS contém VOLTAGEM MORTAL. Todos os reparos e assistência técnica devem ser
executados SOMENTE POR PESSOAL DA ASSISTÊNCIA TÉCNICA AUTORIZADO. Não há
nenhuma PEÇA QUE POSSA SER REPARADA PELO USUÁRIO dentro da UPS.
ADVERTÊNCIA
S Este no-break possui sua própria fonte de energia (baterias). As tomadas de saída podem
estar energizadas mesmo que o no-break não esteja conectado a uma fonte de energia
elétrica.
S Nos modelos 230V, pode ser que as tomadas de saída permaneçam energizadas. Se a
alimentação da sua aplicação for do tipo fase-neutro (como ocorre na maioria das
aplicações na Europa), a tensão das tomadas de saída é de 0 V. Com a alimentação
fase-fase, a tensão das tomadas de saída é de 115V (medida como fase-terra ou
fase-neutro, dependendo da instalação elétrica do no-break).
S Não remova ou desconecte o cabo de entrada quando a UPS estiver ligada. Isto
removerá o aterramento de segurança da UPS e do equipamento conectado.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
13
SAFETY WARNINGS
S Para reduzir o risco de incêndios ou choques elétricos, instale a UPS em ambiente
interno com temperatura e umidade controladas e livres de contaminadores condutíveis.
A temperatura ambiente não deve exceder 40°C. Não opere próximo a água ou em
umidade excessiva (máx: 95%).
S Para estar de acordo com os padrões internacionais e os regulamentos de fiação, o
equipamento total conectado à saída desta UPS não deve ter uma corrente de fuga à
terra maior que 3,5 miliampères.
PERIGO
S As baterias podem oferecer risco de choque elétrico ou queimadura, ocasionados por
alta tensão com possibilidade de curto-circuito. Tome as precauções adequadas. A
manutenção deve ser realizada por pessoal qualificado, com conhecimento sobre
baterias e ciente das precauções exigidas. Mantenha o pessoal não autorizado afastado
das baterias.
S Siga as instruções apropriadas ao desfazer-se das baterias. Consulte os códigos do local
para maiores informações sobre os regulamentos de descarte de produtos.
S Nunca jogue as baterias no fogo, porque há risco de explosão.
Предупреждения по мерам безопасности
ВАЖНЫЕ УКАЗАНИЯ ПО МЕРАМ БЕЗОПАСНОСТИ
СОХРАНИТЕ ЭТИ УКАЗАНИЯ
В данном руководстве содержатся важные инструкции по установке и
обслуживанию источника бесперебойного питания (ИБП) и батарей. Перед
работой с оборудованием прочтите все инструкции. Сохраните данное
руководство для дальнейшего использования.
ОПАСНО
В данном ИБП имеются СМЕРТЕЛЬНО ОПАСНЫЕ НАПРЯЖЕНИЯ. Все
работы по ремонту и обслуживанию должны выполняться ТОЛЬКО
УПОЛНОМОЧЕННЫМ ОБСЛУЖИВАЮЩИМ ПЕРСОНАЛОМ. Внутри
ИБП нет узлов, ОБСЛУЖИВАЕМЫХ ПОЛЬЗОВАТЕЛЕМ.
14
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
SAFETY WARNINGS
ПРЕДУПРЕЖДЕНИЕ
S В данном ИБП установлены собственные источники энергии (батареи).
На выходных розетках может быть напряжение, даже если ИБП не
подключен к сети переменного тока.
S На выходных розетках моделей с напряжением 230 В может быть
напряжение. Если устройство рассчитано на тип подключения
“фаза-нейтраль” (как большинство устройств, изготавливаемых в Европе),
напряжение на выходных розетках равно 0 В. При типе подключения
“фаза-фаза” напряжение на выходных розетках составляет 115 В (при
измерении “фаза-земля” или “фаза-нейтраль”, в зависимости от
электрической схемы ИБП).
S Не отсоединяйте сетевой шнур и не извлекайте его вилку из розетки при
включенном ИБП. При этом защитное заземление отключается от ИБП и
от оборудования, подключенного к ИПБ.
S Для снижения опасности пожара или поражения электрическим током
устанавливайте ИБП в закрытом помещении с контролируемыми
температурой и влажностью, в котором отсутствуют проводящие
загрязняющие вещества. Температура окружающего воздуха не должна
превышать 40°С. Не эксплуатируйте устройство около воды или в местах с
повышенной влажностью (макс. 95%).
S Для обеспечения соблюдения требований международных стандартов и
требований к разводке электрических цепей, суммарная величина тока
утечки на землю всего оборудования, подключенного к выходу ИБП, не
должна превышать 3,5 миллиампера.
ОСТОРОЖНО
S Высокое напряжение, вызванное коротким замыканием в батарее, может
привести к поражению электрическим током или ожогу. Соблюдайте
меры предосторожности. Техническое обслуживание должно
осуществляться квалифицированным персоналом по работе с
источниками питания, знакомым с мерами предосторожности. Не
допускайте к работе с батареями посторонних.
S Необходимо соблюдать правила утилизации аккумуляторов. Обратитесь к
местным нормативным актам за информацией о требованиях к
утилизации.
S Никогда не бросайте аккумуляторы в огонь. Аккумуляторы могут
взорваться под воздействием огня.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
15
SAFETY WARNINGS
Advertencias de Seguridad
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
GUARDE ESTAS INSTRUCCIONES
Este manual contiene instrucciones importantes que debe seguir durante la instalación y el
mantenimiento del SIE y de las baterías. Por favor, lea todas las instrucciones antes de
poner en funcionamiento el equipo y guarde este manual para referencia en el futuro.
PELIGRO
Este SIE contiene VOLTAJES MORTALES. Todas las reparaciones y el servicio técnico deben
ser efectuados SOLAMENTE POR PERSONAL DE SERVICIO TÉCNICO AUTORIZADO. No hay
NINGUNA PARTE QUE EL USUARIO PUEDA REPARAR dentro del SIE.
ADVERTENCIA
S Este SIE contiene su propia fuente de energía (baterías). Los receptáculos de salida
pueden transportar voltaje activo aun cuando el SIE no esté conectado con una fuente de
CA.
S Para los modelos 230V, es posible que los receptáculos de salida permanezcan
eléctricamente activos. Si la fuente de energía de entrada de su aplicación está
cableada de línea a neutro (como la mayoría de las aplicaciones europeas), el voltaje a
los receptáculos de salida es 0V. Con cableado de entrada de línea a línea, el voltaje
hacia los receptáculos de salida es 115V (medido de línea a tierra o de línea a neutro, lo
que dependerá del cableado del SIE).
S No retire o desenchufe el cable de entrada mientras el SIE se encuentre encendido. Esto
suprime la descarga a tierra de seguridad del SIE y de los equipos conectados al SIE.
S Para reducir el riesgo de incendio o de choque eléctrico, instale este SIE en un lugar
cubierto, con temperatura y humedad controladas, libre de contaminantes conductores.
La temperatura ambiente no debe exceder los 40°C. No trabaje cerca del agua o con
humedad excesiva (95% máximo).
S Para cumplir con los estándares internacionales y las normas de instalación, la totalidad
de los equipos conectados a la salida de este SIE no debe tener una intensidad de
pérdida a tierra superior a los 3,5 miliamperios.
16
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
SAFETY WARNINGS
PRECAUCIÓN
S Las baterías pueden constituir un riesgo de descarga eléctrica o quemaduras por
corriente alta de corto circuito. Adopte las precauciones debidas. Personal calificado de
servicio que conozca de baterías y esté al tanto de las precauciones requeridas debe
darle servicio al equipo. Mantenga al personal no autorizado alejado de las baterías.
S Es necesario desechar las baterías de un modo adecuado. Consulte las normas locales
para conocer los requisitos pertinentes.
S Nunca deseche las baterías en el fuego. Las baterías pueden explotar si se las expone a
la llama.
Säkerhetsföreskrifter
VIKTIGA SÄKERHETSFÖRESKRIFTER
SPARA DESSA FÖRESKRIFTER
Den här anvisningen innehåller viktiga instruktioner som du ska följa under installation och
underhåll av UPS-enheten och batterierna. Läs alla instruktioner innan du använder
utrustningen och spara den här anvisningen för framtida referens.
FARA
Denna UPS-enhet innehåller LIVSFARLIG SPÄNNING. ENDAST AUKTORISERAD
SERVICEPERSONAL får utföra reparationer eller service. Det finns inga delar som
ANVÄNDAREN KAN UTFÖRA SERVICE PÅ inuti UPS-enheten.
VARNING
S Den här UPS-enheten innehåller sin egen energikälla (batterier). Uttagen kan vara
spänningsförande även då UPS-enheten inte är ansluten till spänningsnätet.
S På modellerna 230 V kan de utgående uttagen fortfarande vara strömförande. Om den
ingående strömkällan i din applikation är kopplad ledare-till-nolla (det vanligaste i
Europa) är spänningen till de utgående uttagen 0 V. Är den ingående strömkällan kopplad
ledare-till-ledare är spänningen i de utgående uttagen 115 V (uppmätt från
ledare-till-jord eller ledare-till-nolla beroende på UPS:ens anslutning).
S Ta aldrig bort nätsladden när UPS-enheten är påslagen. Detta tar bort skyddsjordningen
från både UPS-enheten och den anslutna utrustningen.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
17
SAFETY WARNINGS
S Minska risken för brand eller elektriska stötar genom att installera denna UPS-enhet
inomhus, där temperatur och luftfuktighet är kontrollerade och där inga ledande
föroreningar förekommer. Omgivande temperatur får ej överstiga 40°C. Använd inte
utrustningen nära vatten eller vid hög luftfuktighet (max 95 %).
S För att överensstämma med internationell standard och installationsföreskrifter får inte
den totala utrustning som anslutits till uttagen på denna UPS-enhet ha läcksström som
överstiger 3,5 milliampere.
VIKTIGT
S Batterierna kan innebära en risk för elektrisk stöt eller brännskada från kortsluten
starkström. Iakttag lämpliga försiktighetsåtgärder. Service ska utföras av utbildad
servicepersonal med kunskap om batterierna och nödvändiga försiktighetsåtgärder. Håll
ej behörig personal borta från batterierna.
S Batterierna måste avyttras enligt anvisningarna i lokal lagstiftning.
S Använda batterier får aldrig brännas upp. De kan explodera.
18
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
Chapter 3
Installation
This section explains:
S Equipment inspection
S UPS internal battery connection
S UPS setup and installation, including Extended Battery Modules
(EBMs)
S Remote power-off (RPO) or remote on/off (ROO) installation
S UPS rear panels
Inspecting the Equipment
If any equipment has been damaged during shipment, keep the shipping
cartons and packing materials for the carrier or place of purchase and file
a claim for shipping damage. If you discover damage after acceptance,
file a claim for concealed damage.
To file a claim for shipping damage or concealed damage: 1) File with
the carrier within 15 days of receipt of the equipment; 2) Send a copy of
the damage claim within 15 days to your service representative.
NOTE Check the battery recharge date on the shipping carton label. If the date has passed
and the batteries were never recharged, do not use the UPS. Contact your service
representative.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
19
INSTALLATION
Checking the Accessory Kit
Verify that the following additional items are included with the UPS:
Table 1. UPS Accessory Kit
Item
Description
UPS user’s guide or CD
Quick start instructions
UPS front cover
USB cable
RS-232 serial cable
Rackmounting kit for 19-inch (48 cm) bays
2U models only.
Two pedestals with screws for tower position
Optional.
Network Management Card
20
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
INSTALLATION
The high-voltage models include the following additional items:
Table 2. Additional High-Voltage Model Accessory Items
Item
Description
Two cord-retention brackets
Two equipment power cords
2500–3000 VA models only.
Power cord
If you ordered an optional EBM, verify that the following items are
included with the EBM:
Table 3. EBM Accessory Items
Item
Description
EBM user’s guide
EBM cable
EBM communication cable
Rackmounting kit for 19-inch (48 cm) bays
Joining bracket and screws for tower position
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
21
INSTALLATION
Connecting the UPS Internal Battery
To ensure proper battery operation:
1.
Verify that the UPS is off and unplugged.
2.
Connect the internal battery connectors by firmly pressing the
connectors together (see Figure 2).
1
2
Figure 2. Connecting the Internal Battery Connectors
NOTE A small amount of arcing may occur when connecting the batteries. This is normal
and does not damage the unit or present any safety concern.
3.
Install the UPS front cover and snap into place (see Figure 3).
1
2
Figure 3. Installing the UPS Front Cover
4.
22
Continue to the following section, “UPS Setup.”
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
INSTALLATION
UPS Setup
The Powerware 5130 UPS is designed for flexible configurations and can
be installed in a rack or as a standalone cabinet.
If you are installing the UPS in a rack, continue to the following section,
“Rackmount Setup;” otherwise, continue to “Tower Setup” on page 25.
Rackmount Setup
The rail kit can be mounted in 19-inch panel (48 cm) racks from 24 to
30 inches (61 to 76 cm) deep and includes:
S Left and right sliding rail assemblies
S (12) M5 washers
S (12) M5×12 mm Phillips® -head screws
S (8) M4×5 mm Phillips-head screws
S (2) mounting brackets with handles
Required Tools
To assemble the components, a #2 Phillips screwdriver may be needed.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
23
INSTALLATION
Installing the Rail Kit
CAUTION
The UPS and EBM are heavy (see page 52). A minimum of two people are required to lift the
cabinets into the rack.
NOTE Mounting rails are required for each UPS and EBM cabinet. If mounting rails are not
already installed in your rack, contact your local distributor to order rail kits.
To install the rail kit:
1.
Adjust the rail size for the depth of your rack.
2.
Select the proper holes in the rail for positioning the UPS in the
desired location in the rack.
3.
Using two M5 washers and two M5 screws, attach the rail to the
rear of the rack (see Figure 4).
4.
Secure the rail to the front of the rack with two M5 washers and
two M5 screws.
5.
Repeat Steps 3 and 4 for the other rail.
1
2
Figure 4. Installing the Rail Kit
24
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
INSTALLATION
6.
Place the UPS on a flat, stable surface with the front of the UPS
facing you.
7.
Attach the supplied mounting brackets to the cabinet and secure
with four M4 screws on each side (see Figure 4).
8.
If installing optional EBMs, repeat Steps 1 and 7 for each cabinet.
NOTE The UPS and EBMs MUST be installed at the bottom of the rack. If placed in a rack
with existing equipment, the rack must be reconfigured to allow the UPS installation at the
bottom of the rack.
NOTE The EBMs must be installed below the UPS.
9.
Slide the UPS and any optional EBMs into the rack.
10. Secure the front of the cabinet to the rack using two M5 washers
and two M5 screws on each side (see Figure 4).
11. Continue to “Installing the UPS” on page 28.
Tower Setup
The setup varies depending on the size of the cabinet you are installing:
2
Carefully position the cabinet upright with the air vents at the top
(see Figure 5).
1
1.
Air Vents
Figure 5. 3U Cabinet
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
25
INSTALLATION
2.
For one 2U cabinet, the pedestals must be installed. Continue to
Step 3.
For one 3U cabinet, continue to “Installing the UPS” on page 28.
For two or more cabinets, the joining brackets must be installed. Skip
to Step 5.
2
Align the pedestals with the screw holes on the sides of the UPS
cabinet. Secure the pedestals with the captive screws.
1
3.
Figure 6. Installing UPS Pedestals (for One 2U Cabinet)
4.
26
Continue to the following section, “Installing the UPS.”
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
INSTALLATION
5.
Align each joining bracket with the adjacent cabinet screw holes
and secure with the supplied screws (see Figure 7).
NOTE Joining brackets are required for installations with two or more cabinets.
Joining Bracket
Figure 7. Installing the Joining Brackets
6.
If installing additional EBMs, repeat Step 5 for each cabinet.
7.
Continue to the following section, “Installing the UPS.”
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
27
INSTALLATION
Installing the UPS
NOTE Do not make unauthorized changes to the UPS or accessories; otherwise, damage
may occur to your equipment and void your warranty.
See “UPS Rear Panels” on page 33 for the rear panel of each model.
To install the UPS and optional EBMs:
1.
If installing an optional EBM, continue to Step 2; otherwise,
continue to Step 3.
2.
Plug the EBM cable into the battery connector. Plug the EBM
communication cable into the RJ-11 port. See Figure 8.
Up to four EBMs may be connected to the UPS.
EBM Communication
Cable
EBM Cable
EBM Battery Connectors
Figure 8. UPS Installation with Four EBMs
28
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
INSTALLATION
3.
If you plan to install power management software, connect your
computer to the USB port or RS-232 communication port using the
supplied communication cable.
OR
Figure 9. Installing a Communication Cable
4.
For rackmount installations only. If your rack has conductors for
grounding or bonding of ungrounded metal parts, connect the
ground cable (not included) to the ground bonding screw. See “UPS
Rear Panels” on page 33.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
29
INSTALLATION
5.
Plug the equipment to be protected into the appropriate UPS output
receptacles (see page 42 for more information on load segments).
See Figure 10.
NOTE DO NOT protect laser printers with the UPS because of the exceptionally high power
requirements of the heating elements.
6.
High-voltage models only. Install the cord-retention bracket to secure
the cords and provide strain relief (see Figure 10).
Plug a 10A power cord into the input connector on the UPS rear
panel (16A power cord supplied for 2500–3000 VA models).
Figure 10. Installing the Power and Equipment Cords (High-voltage only)
30
7.
If you are installing a remote power-off (RPO) or a remote on/off
(ROO) switch, see the following section, “RPO and ROO
Installation,” to install the switch before powering on the UPS.
8.
Continue to “Turning the UPS On” on page 35.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
INSTALLATION
RPO and ROO Installation
The Powerware 5130 includes a two-position terminal (see Figure 11)
that can be either left closed or configured one of two ways:
S RPO: Allows a remote contact to be used to disconnect all equipment
connected to the UPS. Restarting the UPS requires manual
intervention.
S ROO: Allows remote action of the
button to shut down the UPS.
RPO
ROO
Figure 11. RPO/ROO Connection
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
31
INSTALLATION
WARNING
The RPO/ROO circuit is an IEC 60950 safety extra low voltage (SELV) circuit. This circuit must
be separated from any hazardous voltage circuits by reinforced insulation.
To install the RPO or ROO switch:
1.
Verify that the UPS is off and unplugged.
2.
Unscrew and remove the RPO/ROO connector from the RPO/ROO
port on the UPS rear panel.
3.
Refer to the following table to plan the RPO or ROO behavior:
Contact
RPO
Open
UPS shuts down, the
illuminates
Closed
Normal operation
To return to normal operation,
deactivate the remote external
contact and restart the UPS by
pressing the
button
NOTE The local
ROO*
indicator
UPS shuts down
UPS starts up (UPS connected to
AC power and AC power is
available)
button overrides the ROO function.
4.
Connect isolated, normally-closed, dry contacts (rated to handle
60 Vdc maximum, 30 Vac RMS maximum, and 20 mA maximum).
Use stranded, non-shielded wiring, size 0.75 mm2–0.5 mm2
(18–20 AWG).
5.
Reinstall the RPO/ROO connector to the RPO/ROO port.
6.
Verify that the externally-connected RPO switch is not activated to
enable power to the UPS output receptacles.
7.
Plug the UPS power cord into a power outlet.
8.
button until you hear the UPS beep
Press and hold the
(approximately one second).
9.
Activate the external RPO or ROO switch to test the function.
Verify the status change on the UPS front panel.
10. RPO only. De-activate the external RPO switch and restart the UPS.
32
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
INSTALLATION
UPS Rear Panels
This section shows the rear panels of the Powerware 5130 models.
Receptacles
[(6) 5-15R - 1250 VA
(6) 5-15/5-20R - 1750 VA]
USB Port
RS-232 Port
EBM Battery Connector
Communication Bay
Ground Bonding
Screw
EBM RJ-11
Connector
Site Fault Indicator
Power Cord
(15A, 5-15 plug - 1250 VA
20A, 5-20 plug - 1750 VA)
RPO/ROO Connector
Figure 12. 1250–1750 VA, Low-Voltage Rear Panel
USB Port
RS-232 Port
Output Circuit Breakers
EBM Battery Connector
(6) 5-15/5-20 Receptacles
Communication Bay
Ground Bonding
Screw
EBM RJ-11
Connector
Site Fault Indicator
RPO/ROO Connector
Power Cord
(30A, L5-30 plug)
L5-30 Receptacle
Figure 13. 2500–3000 VA, Low-Voltage Rear Panel
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
33
INSTALLATION
USB Port
RS-232 Port
(1) L6-30 Receptacle
EBM Battery Connector
(2) L6-20 Receptacles
Communication
Bay
Ground Bonding Screw
EBM RJ-11 Connector
RPO/ROO Connector
Power Cord
(20A, L6-20 plug)
Figure 14. 208V Rear Panel
USB Port
RS-232 Port
EBM Battery Connector
(8) 10A, IEC 320-C13 Receptacles
Ground Bonding
Screw
Communication
Bay
10A, IEC-C14
Input Connector
EBM RJ-11 Connector
RPO/ROO Connector
Figure 15. 1250–1750 VA, High-Voltage Rear Panel
USB Port
RS-232 Port
EBM Battery Connector
(8) 10A, IEC 320-C13 Receptacles
Ground Bonding
Screw
Communication
Bay
16A, IEC-C20
Input Connector
EBM RJ-11 Connector
(1) 16A, IEC 320-C19 Receptacle
RPO/ROO Connector
Figure 16. 2500–3000 VA, High-Voltage Rear Panel
34
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
Chapter 4
Operation
This section describes:
S Turning the UPS on and off
S Starting the UPS on battery
S Initiating the self-test
S Operating modes
Turning the UPS On
To turn the UPS on:
1.
Plug the UPS power cord into a power outlet.
The
bar graph indicators illuminate, indicating the UPS is in
Standby mode.
2.
button until you hear the UPS beep
Press and hold the
(approximately two seconds).
The alarm beeps once and all front panel indicators flash briefly. The
button and the
illuminate. Conditions permitting, the UPS
bar graph indicators cycle through.
runs a battery test and the
The load segment indicators ( 1 and 2 ) show that power is
available to the output receptacles.
μ
bar graph indicators display the percentage of load being
The
applied to the UPS. The UPS is now in Normal mode and supplying
power to your equipment.
To change the factory-set defaults, see “Customizing the UPS with
the UPS Configuration Tool ” on page 43.
3.
If the
indicator illuminates, see Table 17 on page 58.
NOTE The batteries charge to 90% capacity in approximately 3 hours. However, it is
recommended that the batteries charge for 24 hours after installation or long-term storage.
NOTE If more than two EBMs are installed, an external battery charger is recommended
for faster recharge times.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
35
OPERATION
Starting the UPS on Battery
NOTE Before using this feature, the UPS must have been powered by utility power at least
once.
To turn on the UPS without using utility power, press and hold the
button for two seconds. The UPS starts up in Battery mode and
supplies battery power to your equipment.
Turning the UPS Off
NOTE Pressing the
down immediately.
button while the UPS is in Battery mode causes the UPS to shut
To turn off the UPS:
1.
Prepare your equipment for shutdown.
2.
Press and hold the
button for two seconds. The UPS transfers to
Standby mode (if utility power is available) and removes power from
your equipment.
3.
Unplug the UPS.
If you do not unplug the UPS, it remains in Standby mode.
36
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
OPERATION
Operating Modes
The Powerware 5130 front panel indicates the UPS status through the
UPS indicators. Figure 17 shows the UPS front panel indicators and
controls.
Indicator Legend
Unlit
Normal Mode Indicator
Load Not Protected
Indicator
On/Off Button
Lit
Flashing
1
Load Level Indicators
Battery Charge Level
Indicators
2
Downgraded Operation Indicator
Figure 17. UPS Front Panel
Normal Mode
μ
During Normal mode, the
button and the
indicator illuminate and
the front panel displays the percentage of UPS load capacity being used
by the protected equipment (see Figure 18). The UPS monitors and
charges the batteries as needed and provides power protection to your
equipment.
76-100%
51-75%
26-50%
0-25%
1
2
Figure 18. Load Level Indicators
When all of the bar graph indicators and the
indicator are illuminated,
power requirements exceed UPS capacity; see page 58 for more
information.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
37
OPERATION
Battery Mode
When the UPS is operating during a power outage, the alarm beeps
button, the
, and
indicators
once every 10 seconds and the
bar graph indicators show the level of remaining battery
are on. The
power.
μ
When utility power returns, the UPS transfers to Normal mode operation
while the battery recharges.
If battery capacity becomes low while in Battery mode, the alarm beeps
every three seconds. Immediately complete and save your work to
prevent data loss and similar difficulties.
When utility power is restored after the UPS shuts down, the UPS
automatically restarts.
1
2
0-25%
26-50%
51-75%
76-100%
Figure 19. Battery Charge Level Indicators
Standby Mode
When the UPS is turned off and remains plugged into a power outlet,
bar graph indicators are on and all
the UPS is in Standby mode. The
other indicators are off, indicating that power is not available from the
UPS output receptacles. The battery recharges when necessary.
NOTE For 230V models, the output receptacles may remain electrically live (up to 115V).
Unplug the UPS to ensure power is not available to the output receptacles.
38
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
Chapter 5
Additional UPS Features
This section describes:
S USB port
S RS-232 communication port
S Communication card
S Load segments (PowerShare)
The Powerware 5130 UPS includes a USB port, a RS-232
communication port, and a bay for an optional communication card. The
USB and RS-232 ports cannot operate simultaneously.
USB Port
The UPS can communicate with a USB-compliant computer using
Powerware LanSafe® Power Management Software or other
HID-compliant power management software compatible with Microsoft®
Windows® 2000 and XP operating systems that support HID devices.
NOTE The latest versions of the Powerware LanSafe Power Management Software and
the USB firmware are available at www.powerware.com.
To establish communication between the UPS and a computer:
1.
The USB port is hot-pluggable. Connect the USB cable to the USB
port on the UPS rear panel (see Figure 20).
Connect the other end of the USB cable to the USB port on your
computer.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
39
ADDITIONAL UPS FEATURES
Figure 20. The USB Port
2.
40
Install the Powerware LanSafe Power Management Software and
USB drivers according to the instructions provided at
www.powerware.com.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
ADDITIONAL UPS FEATURES
Contact Communication Port (optional)
When a signal is activated, the contact is closed between the common
(Pin 4) and the pin for the corresponding signal.
Contact characteristics (optocoupler):
S Voltage: 48 V DC max
S Current: 25 mA max
S Power: 1.2W
Figure 21 identifies the cable pins and Table 4 describes the pin
functions.
Common
NO
NO
NO
NOTE Normally-open (NO)
Figure 21. Communication Port
Table 4. Communication Port Pin Assignment
Pin Number
Function
1, 3, 4, 5, 6, 10
Not used
2
Common
7
Low Battery
8
Operation on battery power
9
UPS ON, equipment supplied
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
41
ADDITIONAL UPS FEATURES
Load Segments (PowerShare)
Each UPS has programmable outlets as shown in Figure 22 through
Figure 24. During a power outage, you can keep key pieces of equipment
running while you turn off other equipment. It is preferable to connect
the non-priority loads to the programmable receptacles, 1 and 2 . This
feature allows you to save battery power. See your power management
software manual for details (refer to www.powerware.com for the latest
information).
NOTE If power management software is not used, the individual load segments cannot be
controlled.
1
Programmable Receptacle
2
Programmable Receptacle
Figure 22. Low-Voltage Load Segments
1
Programmable Receptacle
2
Programmable Receptacle
Figure 23. 208V Load Segments
1
Programmable Receptacles
2
Programmable Receptacles
Figure 24. High-Voltage Load Segments
42
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
ADDITIONAL UPS FEATURES
Customizing the UPS with the UPS Configuration Tool
To customize the UPS settings:
1.
Download the UPS Configuration tool from www.powerware.com.
2.
Follow the on-screen instructions for the Powerware 5130.
It is possible to modify the settings listed below (detailed
comments are available in the UPS Configuration tool).
Table 5. Main Output Options
Function
Factory Setting
Other Available Settings
Low-Voltage Models. Output voltage on
battery power
120 Vac
100/120/127 Vac
High-Voltage Models. Output voltage on
battery power
230 Vac
200/208/220/240 Vac
PW5130G3000-XL2U Models. Output
voltage on battery power
208V
—
All Models. Overload alarm threshold
105%
30/50/70%
Factory Setting
Other Available Settings
High threshold for transfer to battery
151 Vac ±3%
141–153 Vac
Low threshold for transfer to battery
89 Vac ±3%
89–94 Vac
Fader activation threshold
132 Vac ±3%
127–138 Vac
Booster activation threshold
102 Vac ±3%
92–108 Vac
Maximum input-voltage range
Disabled
Enabled1
High-Voltage Model Function
Factory Setting
Other Available Settings
High threshold for transfer to battery
294 Vac
271–294 Vac
Low threshold for transfer to battery
160 Vac
160–180 Vac
Fader activation threshold
265 Vac
244–265 Vac
Booster activation threshold
184 Vac
184–207 Vac
Maximum input-voltage range
Disabled
Enabled2
Table 6. Voltage Threshold Options
Low-Voltage Model Function
1 Low threshold for transfer to battery is 70V.
2 Low threshold for transfer to battery is 150V.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
43
ADDITIONAL UPS FEATURES
Table 6. Voltage Threshold Options (continued)
PW5130G3000-XL2U Function
Factory Setting
Other Available Settings
High threshold for transfer to battery
263 Vac
—
Low threshold for transfer to battery
160 Vac
—
Fader activation threshold
229 Vac
—
Booster activation threshold
177 Vac
—
Maximum input-voltage range
Disabled
Enabled2
Factory Setting
Other Available Settings
Normal
High or low
Factory Setting
Other Available Settings
Automatic start
Enabled
Disabled
Cold start
Enabled
Disabled
Forced shutdown
Enabled
Disabled
Energy-savings mode
Disabled
Enabled
UPS ON/OFF controlled by software
Enabled
Disabled
0%
0–100%
Factory Setting
Other Available Settings
Battery-test intervals
Weekly
No test / daily test / monthly test
Low-battery warning
20%
0–100%
Battery protection against deep discharge
Enabled
Disabled
Audio alarm
Enabled
Disabled
Automatic detection of number of
battery modules
For specific batteries, 25–81 Ah
2 Low threshold for transfer to battery is 150V.
Table 7. UPS Sensitivity Options
Function
UPS-sensitivity level
Table 8. UPS On/Off Options
Function
Battery level before restart
Table 9. Battery Options
Function
Additional battery module
44
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
Chapter 6
UPS Maintenance
This section explains how to:
S Care for the UPS and batteries
S Transport the UPS
S Store the UPS and batteries
S Replace the batteries
S Test new batteries
S Recycle used batteries or UPS
UPS and Battery Care
For the best preventive maintenance, keep the area around the UPS
clean and dust-free. If the atmosphere is very dusty, clean the outside of
the system with a vacuum cleaner.
For full battery life, keep the UPS at an ambient temperature of
25°C (77°F).
NOTE The batteries in the UPS are rated for a 3–5 year service life. The length of service
life varies, depending on the frequency of usage and ambient temperature. Batteries used
beyond expected service life will often have severely reduced runtimes. Replace batteries at
least every 5 years to keep units running at peak efficiency.
Transporting the UPS
NOTE The internal UPS batteries MUST be disconnected.
If the UPS requires any type of transportation:
1.
Verify that the UPS is unplugged and turned off.
2.
Disconnect the UPS internal battery connector using the steps in
“Connecting the UPS Internal Battery” on page 22 in reverse order.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
45
UPS MAINTENANCE
Storing the UPS and Batteries
If you store the UPS for a long period, recharge the battery every
6 months by plugging the UPS into a power outlet. The batteries charge
to 90% capacity in approximately 3 hours. However, it is recommended
that the batteries charge for 24 hours after long-term storage.
Check the battery recharge date on the shipping carton label. If the date
has expired and the batteries were never recharged, do not use the
UPS. Contact your service representative.
When to Replace Batteries
If all four
bar graph indicators flash and either the
or
indicators are on, the batteries may need replacing. Contact your service
representative to order new batteries.
Replacing Batteries
NOTE DO NOT DISCONNECT the batteries while the UPS is in Battery mode.
With the hot-swappable battery feature, UPS batteries can be replaced
easily without turning the UPS off or disconnecting the load.
If you prefer to remove input power to change the batteries, see
“Turning the UPS Off” on page 36.
Consider all warnings, cautions, and notes before replacing batteries.
WARNING
S Batteries can present a risk of electrical shock or burn from high short-circuit current. The
following precautions should be observed: 1) Remove watches, rings, or other metal
objects; 2) Use tools with insulated handles; 3) Do not lay tools or metal parts on top of
batteries.
S ELECTRIC ENERGY HAZARD. Do not attempt to alter any battery wiring or connectors.
Attempting to alter wiring can cause injury.
46
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
UPS MAINTENANCE
How to Replace Internal Batteries
CAUTION
S Pull the battery out onto a flat, stable surface. The battery is unsupported when you pull
it out of the UPS.
S To ensure safety and high performance, use only batteries supplied by Eaton.
To replace the UPS internal batteries:
1.
Remove the UPS front cover. Press the button on the left side of
the cover and then pull the left side (see Figure 25).
1
2
Figure 25. Removing the UPS Front Cover
2.
Disconnect the internal battery connectors (see Figure 26).
1
2
Figure 26. Disconnecting the Internal Battery Connectors
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
47
UPS MAINTENANCE
3.
Unscrew and remove the metal battery cover (see Figure 27).
1
2
Figure 27. Removing the Battery Cover
4.
Pull the battery block out onto a flat, stable surface (see Figure 28).
See “Recycling the Used Battery or UPS” on page 50 for proper
disposal.
1
2
Figure 28. Removing the Battery Block
48
5.
Install the new batteries in the reverse order of removal.
6.
Replace the metal battery cover.
7.
Replace the UPS front cover.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
UPS MAINTENANCE
How to Replace Extended Battery Modules
To replace the Extended Battery Modules (EBMs):
1.
Unplug the EBM cable from the UPS.
If additional EBMs are installed, unplug the EBM cable from the
battery connector on each EBM.
2.
Unplug the EBM communication cable from the RJ-11 port. Repeat
for each EBM.
3.
For tower models only. Remove the joining bracket between cabinets.
Joining Bracket
EBM Communication
Cable
EBM Cable
EBM Battery Connectors
Figure 29. EBM Connections (230V Tower Model Shown)
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
49
UPS MAINTENANCE
4.
Replace the EBM. See “Recycling the Used Battery or UPS” on
page 50 for proper disposal.
5.
For tower models only. Install the joining bracket between cabinets.
6.
Plug the new EBM into the UPS as shown in Figure 29.
For additional EBMs, plug the EBM cable into the battery connector
on the adjacent EBM.
7.
Plug the EBM communication cable into the RJ-11 port. Repeat for
each EBM.
Recycling the Used Battery or UPS
Contact your local recycling or hazardous waste center for information
on proper disposal of the used battery or UPS.
WARNING
S Do not dispose of the battery or batteries in a fire. Batteries may explode. Proper
disposal of batteries is required. Refer to your local codes for disposal requirements.
S Do not open or mutilate the battery or batteries. Released electrolyte is harmful to the
skin and eyes. It may be toxic.
CAUTION
Do not discard the UPS or the UPS batteries in the trash. This product contains sealed,
lead-acid batteries and must be disposed of properly. For more information, contact your
local recycling/reuse or hazardous waste center.
CAUTION
Do not discard waste electrical or electronic equipment (WEEE) in the trash. For proper
disposal, contact your local recycling/reuse or hazardous waste center.
50
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
Chapter 7
Specifications
Transformer
“AVR”
Filter
Charger
Inverter
Battery
Figure 30. Block Diagram
Table 10. Low-Voltage Model Specifications
Model Number
Power Levels
(Rated at
Nominal Inputs)
PW5130L1250-XL2U
1250 VA, 1150W
PW5130L1750-XL2U
1750 VA, 1600W
PW5130L2500-XL2U
2500 VA, 2250W
AC Input
Nominal
Voltage
Voltage
Range1
Frequency
Range2
Voltage3
Frequency
120V
89–151V
47–70 Hz (50 Hz
system),
56.5–70 Hz (60 Hz
system)
120V
(+6/-10%)
50/60 Hz
±0.1%
PW5130L3000-XL2U
PW5130L3000-XL3U
Output on Battery Power
2880 VA, 2700W
1 The high and low thresholds can be adjusted using the UPS Configuration tool (see page 43).
2 Up to 40 Hz in low-sensitivity mode (programmable using the UPS Configuration tool).
3 Adjustable to 100V (10% derating of output power) 120/127V.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
51
SPECIFICATIONS
Table 11. High-Voltage Model Specifications
Model Number
Power Levels
(Rated at
Nominal Inputs)
PW5130i1250-XL2U
1250 VA, 1150W
PW5130i1750-XL2U
1750 VA, 1600W
PW5130i2500-XL2U
2500 VA, 2250W
AC Input
Nominal
Voltage
Voltage
Range1
Frequency
Range2
Voltage3
220–240V
160–294V
47–70 Hz (50 Hz
system),
56.5–70 Hz (60 Hz
system)
230V
(+6/-10%)
PW5130i3000-XL2U
PW5130i3000-XL3U
PW5130G3000-XL2U
3000 VA, 2700W
3000 VA, 2700W
Output on Battery Power
208V
208V
(+6/-10%)
160–263V
1 The high and low thresholds can be adjusted using the UPS Configuration tool (see page 43).
2 Up to 40 Hz in low-sensitivity mode (programmable using the UPS Configuration tool).
3 Adjustable to 100V (10% derating of output power) 120/127V.
Table 12. Weights and Dimensions
Low-Voltage Model Number
Dimensions (WxHxD)
Weight
PW5130L1250-XL2U
440×86×509 mm
17.3”×3.4”×20.0”
24.6 kg (54.3 lb)
440×86×634 mm
17.3”×3.4”×25.0”
34.7 kg (76.4 lb)
PW5130L1750-XL2U
PW5130L2500-XL2U
PW5130L3000-XL2U
35.3 kg (77.9 lb)
PW5130L3000-XL3U
440×131×484 mm
17.3”×5.2”×19.0”
33.8 kg (75.5 lb)
High-Voltage Model Number
Dimensions (WxHxD)
Weight
PW5130i1250-XL2U
440×86×509 mm
17.3”×3.4”×20.0”
24.3 kg (53.6 lb)
440×86×634 mm
17.3”×3.4”×25.0”
33.8 kg (74.5 lb)
PW5130G3000-XL2U
440×86×634 mm
17.3”×3.4”×25.0”
35.3 kg (77.9 lb)
PW5130i3000-XL3U
440×131×484 mm
17.3”×5.2”×19.0”
34.3 kg (75.6 lb)
PW5130i1750-XL2U
PW5130i2500-XL2U
PW5130i3000-XL2U
52
26.3 kg (58.0 lb)
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
Frequency
50/60 Hz
±0.1%
SPECIFICATIONS
Table 12. Weights and Dimensions (continued)
EBM Model Number
Dimensions (WxHxD)
Weight
PW5130N1750-EBM2U
440×86×509 mm
17.3”×3.4”×20.0”
29.1 kg (64.2 lb)
PW5130N3000-EBM2U
440×86×634 mm
17.3”×3.4”×25.0”
42.0 kg (92.7 lb)
PW5130N3000-EBM3U
440×131×484 mm
17.3”×5.2”×19.0”
39.9 kg (88.0 lb)
Table 13. Power Connections
Model
Input Connection
Output Receptacles
PW5130L1250-XL2U
6 ft, 15A, 5-15P power cord
(6) 5-15R
PW5130L1750-XL2U
6 ft, 20A, 5-20P power cord
(6) 5-15/5-20R
6 ft, 30A, L5-30P power cord
(6) 5-15/5-20R; (1) L5-30R
10A, IEC-C14 input connector
(8) 10A, IEC 320-C13
16A, IEC-C20 input connector
(8) 10A, IEC 320-C13; (1) 16A, IEC 320-C19
6 ft, 20A, L6-20P power cord
(1) L6-30R; (2) L6-20R
PW5130L2500-XL2U
PW5130L3000-XL2U
PW5130L3000-XL3U
PW5130i1250-XL2U
PW5130i1750-XL2U
PW5130i2500-XL2U
PW5130i3000-XL2U
PW5130i3000-XL3U
PW5130G3000-XL2U
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
53
SPECIFICATIONS
Table 14. Environmental and Safety
Low Voltage Models
Operating Temperature
0°C to 40°C (32°F to 104°F)
Storage Temperature
-25°C to 40°C (-13°F to 104°F)
Relative Humidity
Audible Noise
Surge Suppression
Safety Conformance
Agency Markings
EMC
High Voltage Models
Storage: 10–95% noncondensing
Operating: 20–95% noncondensing
Less than 40 dBA Normal mode, typical load
Less than 45 dBA (50 dBA for 3000 VA) Battery mode
ANSI C62.41 Category B, IEC 61000-4-5
UL 1778, UL 497A;
CSA C22.2, No. 107.1;
NOM-019-SCFI
UL 1778, UL 497A (data line only);
CSA C22.2, No. 107.1;
EN 62040-1-1, IEC 60950-1, IEC 50091-1-1
cULus, cUL
cTUVus, CE
FCC Part 15 Class A
EN 62040-2 C1, AS 62040-2 C1,
FCC Part 15 Class B
Table 15. Battery
UPS Configuration
1250 VA: (4) 12V, 7.2 Ah internal batteries
1750 VA: (4) 12V, 9 Ah internal batteries
2500 VA: (6) 12V, 7.2 Ah internal batteries
3000 VA: (6) 12V, 9 Ah internal batteries
EBM Configuration
PW5130N1750-EBM2U: 48 Vdc, (2 stings of 4) 12V, 9 Ah batteries
PW5130N3000-EBM2U and PW5130N3000-EBM3U: 72 Vdc, (2 strings of 6)
12V, 9 Ah batteries
Type
54
Sealed, maintenance-free, valve-regulated, lead-acid
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
SPECIFICATIONS
Table 16. Battery Runtimes
Half Load
UPS Internal Batteries
+1 EBM
+2 EBMs
+3 EBMs
+4 EBMs
1250 VA/575W
15 min 22 sec
58 min
1 hr 40 min
2 hr 23 min
3 hr 5 min
1750 VA/800W
9 min 35 sec
36 min 11 sec
1 hr 2 min
1 hr 29 min
1 hr 55 min
2500 VA/1125W
11 min 15 sec
55 min
1 hr 40 min
2 hr 30 min
3 hr 26 min
3000 VA/2700W
10 min 15 sec
44 min
1 hr 13 min
1 hr 41 min
2 hr 10 min
UPS Internal Batteries
+1 EBM
+2 EBMs
+3 EBMs
+4 EBMs
1250 VA/1150W
5 min
29 min 49 sec
54 min 38 sec
1 hr 19 min
1 hr 44 min
1750 VA/1600W
3 min 30 sec
16 min
28 min 30 sec
41 min
53 min 30 sec
2500 VA/2250W
3 min
23 min
42 min
1 hr 3 min
1 hr 25 min
3000 VA/2700W
3 min
17 min
32 min
47 min
1 hr 2 min
Full Load
NOTE Battery times are approximate and vary depending on the load configuration and battery charge.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
55
SPECIFICATIONS
56
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
Chapter 8
Troubleshooting
This section explains:
S UPS alarms and conditions
S Service and support
Audible Alarms and UPS Conditions
The UPS has an audible alarm feature to alert you of potential power
problems. Use Table 17 to determine and resolve the UPS alarms and
conditions.
Indicator Legend
Unlit
Normal Mode Indicator
Load Not Protected
Indicator
On/Off Button
Load Level Indicators
Battery Charge Level
Indicators
Lit
Flashing
1
2
Downgraded Operator Indicator
Figure 31. Alarm Indicators
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
57
TROUBLESHOOTING
Table 17. Troubleshooting Guide
Alarm or Condition
Possible Cause
Action
When starting the UPS with the
button, all the indicators turn on
once, the alarm beeps once, and
then
indicator remains on.
The remote power-off (RPO)
contact has been activated to
shut down the UPS and now
prevents restart.
Set the contact back to its normal position
and press the
button to restart.
The percent load is greater than
the set overload level or UPS
capacity.
Check the power drawn by the connected
devices and disconnect any non-priority
devices. Check the overload setting.
A critical overload has occurred.
If utility power fails, the load will
not be protected in Battery
mode.
Check the power drawn by the connected
devices and disconnect any non-priority
devices.
A battery fault has been
detected during the automatic
test.
Replace the battery (see “Replacing
Batteries” on page 46).
UPS fault condition. The load is
not supplied.
Contact your service representative.
μ
The
button,
and
indicators are on and all the
bar graph indicators flash.
The
button and
are on and all the
indicators flash.
The
indicator
bar graph
indicator is on and all the
bar graph indicators flash.
The
indicator alone is on and
the alarm sounds continuously.
58
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
TROUBLESHOOTING
Service and Support
If you have any questions or problems with the UPS, call your Local
Distributor or the Help Desk at one of the following telephone numbers
and ask for a UPS technical representative.
United States:
Canada:
All other countries:
1-800-356-5737 or 1-919-870-3149
1-800-461-9166 ext 260
Call your local service representative
Please have the following information ready when you call the Help
Desk:
S Model number
S Serial number
S Version number (if available)
S Date of failure or problem
S Symptoms of failure or problem
S Customer return address and contact information
If repair is required, you will be given a Returned Material Authorization
(RMA) Number. This number must appear on the outside of the package
and on the Bill Of Lading (if applicable). Use the original packaging or
request packaging from the Help Desk or distributor. Units damaged in
shipment as a result of improper packaging are not covered under
warranty. A replacement or repair unit will be shipped, freight prepaid for
all warrantied units.
NOTE For critical applications, immediate replacement may be available. Call the Help
Desk for the dealer or distributor nearest you.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
59
TROUBLESHOOTING
60
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
Chapter 9
Warranty
Two-Year Limited Warranty (US and Canada)
Powerware UPS Models: 5110, 5115, 5125, and 5130
WARRANTOR: The warrantor for the limited warranties set forth herein is Eaton Electrical, Inc., a Delaware
Corporation company (“Company”).
LIMITED WARRANTY: This limited warranty (this “Warranty”) applies only to the original End-User (the “End-User”)
of any Powerware 5110, 5115, 5125, and 5130 Products (individually and collectively, the “Product”) purchased on
or after June 1, 2004 and cannot be transferred. This Warranty applies even in the event that the Product is initially
sold by Company for resale to an End-User.
LIMITED WARRANTY PERIOD: The period covered by this Warranty for the Product installed [and currently located]
in the fifty (50) United States, the District of Columbia, and Canada is twenty-four (24) months from the date of
purchase.
WHAT THIS LIMITED WARRANTY COVERS: The warrantor warrants that the Product and battery (individually and
collectively, the ”Warranted Items”) are free of defects in material and workmanship. If, in the opinion of Company,
a Warranted Item is defective and the defect is within the terms of this Warranty, Company’s sole obligation will be
to repair or replace such defective Warranted Item (including by providing service, parts and labor, as applicable), at
the option of Company.
PROCEDURES FOR REPAIR OR REPLACEMENT OF WARRANTED ITEMS: The Warranted Item will be repaired or
replaced at a Company site or such other location as determined by Company.
If the Warranted Item is to be replaced by Company, and the End-User supplies a credit card number or purchase
order for the value of the replacement Product, Company will use commercially reasonable business efforts to ship
(via overnight express shipment and at no cost to the End-User) the replacement Warranted Item to the End-User
within one (1) business day after Company receives notice of the warranty claim. In such case, the End-User must
return (at Company’s expense) the defective Warranted Item to Company in the same packaging as the
replacement Warranted Item received by the End-User or as otherwise instructed by Company. If Company does
not receive the defective Warranted Item, Company will either charge the End-User’s credit card, or send the
End-User an invoice (which the End-User agrees to pay), for the value of the replacement Product.
If the Warranted Item is to be replaced by Company, but the End-User is unwilling or unable to supply a credit card
number or purchase order for the value of the replacement Product, Company will use commercially reasonable
business efforts to ship (via overnight express shipment and at no cost to the End-User) the replacement Warranted
Item to the End-User within one (1) business day after Company receives the defective Product from the End-User.
In any case, Company will provide shipping instructions and will pay its designated carrier for all shipping charges for
return of defective equipment and replacement of Warranted Items. Any returned Warranted Item or parts that are
replaced may be new or reconditioned. All Warranted Items returned to Company and all parts replaced by
Company shall become the property of Company.
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
61
WARRANTY
WHAT THIS LIMITED WARRANTY DOES NOT COVER: This Warranty does not cover any defects or damages
caused by: (a) failure to properly store the Product before installation, including the charge of batteries no later than
the date indicated on the packaging; (b) shipping and delivery of the Product if shipping is FOB Factory; (c) neglect,
accident, abuse, misuse, misapplication, or incorrect installation; (d) repair or alteration not authorized in writing by
Company personnel or performed by an authorized Company Customer Service Engineer or Agent; (e) improper
testing, operation, maintenance, adjustment, or modification of any kind not authorized in writing by Company
personnel or performed by an authorized Company Customer Service Engineer or Agent; or (f) use of the Product
under other than normal operating conditions or in a manner inconsistent with the Product’s labels or instructions.
This Warranty is not valid if the Product’s serial numbers have been removed or are illegible. Any Warranted Items
repaired or replaced pursuant to this Warranty will be warranted for the remaining portion of the original Warranty
subject to all the terms thereof.
Company shall not be responsible for any charges for testing, checking, removal or installation of Warranted Items.
COMPANY DOES NOT WARRANT EQUIPMENT NOT MANUFACTURED BY COMPANY. IF PERMITTED BY THE
APPLICABLE MANUFACTURER, COMPANY SHALL PASS THROUGH SUCH MANUFACTURER’S WARRANTIES TO
END-USER.
COMPANY DOES NOT WARRANT SOFTWARE, INCLUDING SOFTWARE EMBEDDED IN PRODUCTS, THAT IS NOT
CREATED BY COMPANY. WITHOUT LIMITING THE FOREGOING, COMPANY SPECIFICALLY DOES NOT WARRANT
SOFTWARE (SUCH AS LINUX) THAT WAS CREATED USING AN “OPEN SOURCE” MODEL OR IS DISTRIBUTED
PURSUANT TO AN OPEN SOURCE LICENSE.
THIS WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY OFFERED BY COMPANY WITH RESPECT TO THE
PRODUCTS AND SERVICES AND, EXCEPT FOR SUCH FOREGOING WARRANTY COMPANY DISCLAIMS ALL OTHER
WARRANTIES INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, TITLE,
NON-INFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE. CORRECTION OF NON-CONFORMITIES IN
THE MANNER AND FOR THE PERIOD OF TIME PROVIDED ABOVE SHALL CONSTITUTE COMPANY’S SOLE
LIABILITY AND END-USER’S EXCLUSIVE REMEDY FOR FAILURE OF COMPANY TO MEET ITS WARRANTY
OBLIGATIONS, WHETHER CLAIMS OF THE END-USER ARE BASED IN CONTRACT, IN TORT (INCLUDING
NEGLIGENCE OR STRICT LIABILITY), OR OTHERWISE.
LIMITATION OF LIABILITY: The remedies of the End-User set forth herein are exclusive and are the sole remedies
for any failure of Company to comply with its obligations hereunder. In no event shall Company be liable in contract,
in tort (including negligence or strict liability) or otherwise for damage to property or equipment other than the
Products, including loss of profits or revenue, loss of use of Products, loss of data, cost of capital, claims of
customers of the End-User or any special, indirect, incidental or consequential damages whatsoever. The total
cumulative liability of Company hereunder whether the claims are based in contract (including indemnity), in tort
(including negligence or strict liability) or otherwise, shall not exceed the price of the Product on which such liability
is based.
Company shall not be responsible for failure to provide service or parts due to causes beyond Company’s
reasonable control.
END-USER’S OBLIGATIONS: In order to receive the benefits of this Warranty, the End-User must use the Product
in a normal way; follow the Product’s user’s guide; and protect against further damage to the Product if there is a
covered defect.
OTHER LIMITATIONS: Company’s obligations under this Warranty are expressly conditioned upon receipt by
Company of all payments due to it (including interest charges, if any). During such time as Company has not
received payment of any amount due to it for the Product, in accordance with the contract terms under which the
Product is sold, Company shall have no obligation under this Warranty. Also during such time, the period of this
Warranty shall continue to run and the expiration of this Warranty shall not be extended upon payment of any
overdue or unpaid amounts.
62
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
WARRANTY
COSTS NOT RELATED TO WARRANTY: The End-User shall be invoiced for, and shall pay for, all services not
expressly provided for by the terms of this Warranty, including without limitation, site calls involving an inspection
that determines no corrective maintenance is required. Any costs for replacement equipment, installation, materials,
freight charges, travel expenses or labor of Company representatives outside the terms of this Warranty will be
borne by the End-User.
OBTAINING WARRANTY SERVICE: In the USA, call the Customer Reliability Center 7x24 at 800-356-5737. Outside
of the USA, contact your local Powerware product sales or service representative, or call the Customer Reliability
Center in the USA at 919-870-3149. For comments or questions about this Warranty, write to the Customer Quality
Representative, 3301 Spring Forest Road, Raleigh, North Carolina 27616 USA.
Ten-Year Pro-Rated Limited Warranty (US and Canada)
Powerware UPS Models: 5115, 5125, 5130, 5140, 9120, 9125, 9155, 9170+, and FERRUPS®
WARRANTOR: The warrantor for the limited warranties set forth herein is Eaton Electrical Inc., a Delaware
Corporation company (“Company”).
LIMITED WARRANTY: This pro-rated limited warranty (this “Warranty”) applies only to the original End-User (the
“End-User”) of any Powerware 5115, 5125, 5130, 5140, 9120, 9125, 9155, 9170+, and FERRUPS Products
(individually and collectively, the “Product”) and cannot be transferred. This Warranty applies even in the event that
the Product is initially sold by Company for resale to an End-User.
WHAT THIS WARRANTY COVERS: In addition to the standard Two-Year Limited Warranty covering the applicable
Product, the warrantor warrants that the Product will have a service life (defined below) of ten years from the date
of purchase (the “Ten-Year Service Life”) when used in accordance with the storage, handling, installation,
operation and maintenance procedures prescribed in the Product’s user’s guide. “Service life” means the Product’s
ability to deliver at least 80% of its original rated backup time.
If Company finds, in its sole discretion, that any Product has not provided the Ten-Year Service Life, Company will,
as its sole obligation and the End-User’s sole remedy for Company’s breach of this warranty, repair or replace the
Product, at its option, F.O.B. Company’s factory, for a charge, payable by the End-User to Company pro-rated on the
following basis:
The End-User will be allowed a credit against Company’s list price of equivalent equipment at the time of return of
the Product to Company, in proportion to the percentage of Ten-Year Service Life remaining at the time of return of
the Product to Company. In calculating the available credit, the remaining portion of the Ten-Year Service Life will be
rounded up or down to the nearest whole year. The End-User will assume responsibility to pay the balance of the
list price; and Company reserves the right to require payment prior to delivery of the repaired or replacement
equipment.
For the avoidance of doubt, Company’s responsibilities under this Warranty are as follows:
Years 1-2 - Product repaired or replaced pursuant to terms of Limited Warranty
Years 3-10 - Unit Credit ($) = Current List Price
×
Years of Unexpired Life
10 Years of Warranted Life
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
63
WARRANTY
WHAT THIS LIMITED WARRANTY DOES NOT COVER: This Warranty does not cover any defects or damages
caused by: (a) failure to properly store the Product before installation, including the charge of batteries no later than
the date indicated on the packaging; (b) shipping and delivery of the Product if shipping is FOB Factory; (c) neglect,
accident, abuse, misuse, misapplication, or incorrect installation; (d) repair or alteration not authorized in writing by
Company personnel or performed by an authorized Company Customer Service Engineer or Agent; (e) improper
testing, operation, maintenance, adjustment, or modification of any kind not authorized in writing by Company
personnel or performed by an authorized Company Customer Service Engineer or Agent; or (f) use of the Product
under other than normal operating conditions or in a manner inconsistent with the Product’s labels or instructions.
This Warranty is not valid: (a) unless the End-User returns to Company the Warranty Registration Card within
thirty (30) days of purchase; or (b) if the Product’s serial numbers have been removed or are illegible. Any
Warranted Items repaired or replaced pursuant to this Warranty will be warranted for the remaining portion of the
original Warranty subject to all the terms thereof.
Company shall not be responsible for any charges for testing, checking, removal or installation of Warranted Items.
COMPANY DOES NOT WARRANT EQUIPMENT NOT MANUFACTURED BY COMPANY. IF PERMITTED BY THE
APPLICABLE MANUFACTURER, COMPANY SHALL PASS THROUGH SUCH MANUFACTURER’S WARRANTIES TO
END-USER.
COMPANY DOES NOT WARRANT SOFTWARE, INCLUDING SOFTWARE EMBEDDED IN PRODUCTS, THAT IS NOT
CREATED BY COMPANY. WITHOUT LIMITING THE FOREGOING, COMPANY SPECIFICALLY DOES NOT WARRANT
SOFTWARE (SUCH AS LINUX) THAT WAS CREATED USING AN “OPEN SOURCE” MODEL OR IS DISTRIBUTED
PURSUANT TO AN OPEN SOURCE LICENSE.
THIS WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY OFFERED BY COMPANY WITH RESPECT TO THE
PRODUCTS AND SERVICES AND, EXCEPT FOR SUCH FOREGOING WARRANTY COMPANY DISCLAIMS ALL OTHER
WARRANTIES INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, TITLE,
NON-INFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE. CORRECTION OF NON-CONFORMITIES IN
THE MANNER AND FOR THE PERIOD OF TIME PROVIDED ABOVE SHALL CONSTITUTE COMPANY’S SOLE
LIABILITY AND END-USER’S EXCLUSIVE REMEDY FOR FAILURE OF COMPANY TO MEET ITS WARRANTY
OBLIGATIONS, WHETHER CLAIMS OF THE END-USER ARE BASED IN CONTRACT, IN TORT (INCLUDING
NEGLIGENCE OR STRICT LIABILITY), OR OTHERWISE.
LIMITATION OF LIABILITY: The remedies of the End-User set forth herein are exclusive and are the sole remedies
for any failure of Company to comply with its obligations hereunder. In no event shall Company be liable in contract,
in tort (including negligence or strict liability) or otherwise for damage to property or equipment other than the
Products, including loss of profits or revenue, loss of use of Products, loss of data, cost of capital, claims of
customers of the End-User or any special, indirect, incidental or consequential damages whatsoever. The total
cumulative liability of Company hereunder whether the claims are based in contract (including indemnity), in tort
(including negligence or strict liability) or otherwise, shall not exceed the price of the Product on which such liability
is based.
Company shall not be responsible for failure to provide service or parts due to causes beyond Company’s
reasonable control.
END-USER’S OBLIGATIONS: In order to receive the benefits of this Warranty, the End-User must use the Product
in a normal way; follow the Product’s operation and maintenance manual; and protect against further damage to the
Product if there is a covered defect.
64
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
WARRANTY
OTHER LIMITATIONS: Company’s obligations under this Warranty are expressly conditioned upon receipt by
Company of all payments due to it (including interest charges, if any). During such time as Company has not
received payment of any amount due to it for the Product, in accordance with the contract terms under which the
Product is sold, Company shall have no obligation under this Warranty. Also during such time, the period of this
Warranty shall continue to run and the expiration of this Warranty shall not be extended upon payment of any
overdue or unpaid amounts.
COSTS NOT RELATED TO WARRANTY: The End-User shall be invoiced for, and shall pay for, all services not
expressly provided for by the terms of this Warranty, including without limitation, site calls involving an inspection
that determines no corrective maintenance is required. Any costs for replacement equipment, installation, materials,
freight charges, travel expenses or labor of Company representatives outside the terms of this Warranty will be
borne by the End-User.
OBTAINING WARRANTY SERVICE: In the USA, call the Customer Reliability Center 7x24 at 800-356-5737. Outside
of the USA, contact your local Powerware product sales or service representative, or call the Customer Reliability
Center in the USA at 919-870-3149. Company will not accept any Product for return, credit or exchange unless
expressly authorized by Company in writing and delivered FOB Company factory. For comments or questions about
this Warranty, write to the Customer Quality Representative, 3301 Spring Forest Road, Raleigh, North Carolina
27616 USA.
Load Protection Guarantee (US and Canada)
Powerware UPS Models 3105, 5110, 5115, 5125, 5130, 9120, 9125, 9150, 9155, 9170+, and FERRUPS
GUARANTOR: The Guarantor for the load protection guaranty set forth herein is Eaton Electrical Inc., a Delaware
Corporation company (“Company”).
LIMITED GUARANTY: This load protection guaranty (this “Guaranty”) applies only to the original End-User (the
“End-User”) of any Powerware 3105, 5110, 5115, 5125, 5130, 9120, 9125, 9150, 9155, 9170+, and FERRUPS
Products (individually and collectively, the “Product”) and cannot be transferred. This Guaranty applies even in the
event that the Product is initially sold by Company for resale to an End-User.
WHAT THIS GUARANTY COVERS: For the lifetime of the Product, Guarantor promises to repair or replace, at
Guarantor’s option, the equipment (valued up to the limits shown below*) that is damaged by an AC power line
surge, spike, or other transient when properly connected to Guarantor’s uninterruptible power system (“UPS”).
Reimbursement for or restoration of data loss excluded. This Guaranty applies only if all of the following
circumstances arise:
1. The UPS is plugged into properly grounded and wired outlets, using no extension cords, adapters, other ground
wires or other electrical connectors;
2. The installation of the UPS complies with all applicable electrical and safety codes described by the National
Electric Code® (NEC)®;
3. The UPS was used under normal operating conditions and in accordance with all labels and instructions; and
4. The UPS was not damaged by accident (other than AC power line transient), misuse, or abuse.
*Cumulative Limits to be paid by Guarantor under this Load Protection Guaranty:
S
$25,000 for Powerware UPS Model 3105
S
$150,000 for Powerware UPS Models 5110, 5115, 5125, and 5130
S
$250,000 for Powerware UPS Models 9120, 9125, 9150, 9155, 9170+, and FERRUPS products
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
65
WARRANTY
WHAT THIS GUARANTY DOES NOT COVER: Any reimbursement or repair to End-User’s equipment does not
include reimbursement for or restoration of any data loss. This Guaranty does not cover any defects or damages
caused by: (a) failure to properly store the Product before installation, including the charge of batteries no later than
the date indicated on the packaging; (b) shipping and delivery of the Product if shipping is FOB Factory; (c) neglect,
accident, abuse, misuse, misapplication, or incorrect installation of Product; (d) repair or alteration of Product not
authorized in writing by Company personnel or performed by an authorized Company Customer Service Engineer or
Agent; (e) improper testing, operation, maintenance, adjustment, or modification of any kind to the Product not
authorized in writing by Company personnel or performed by an authorized Company Customer Service Engineer or
Agent; or (f) use of the Product under other than normal operating conditions or in a manner inconsistent with the
Product’s labels or instructions.
This Guaranty is not valid: (a) unless the End-User returns to Company the Warranty Registration Card within
thirty (30) days of purchase; or (b) if the Product’s serial numbers have been removed or are illegible.
Company shall not be responsible for any charges for testing, checking, removal or installation of any items.
LIMITATION OF LIABILITY: THE REMEDIES OF THE END-USER SET FORTH HEREIN ARE EXCLUSIVE AND ARE THE
SOLE REMEDIES FOR ANY FAILURE OF COMPANY TO COMPLY WITH ITS OBLIGATIONS HEREUNDER. EXCEPT AS
OTHERWISE PROVIDED FOR IN THIS GUARANTY, IN NO EVENT SHALL COMPANY BE LIABLE IN CONTRACT, IN TORT
(INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR OTHERWISE FOR DAMAGE TO PROPERTY OR EQUIPMENT OTHER
THAN THE PRODUCTS, INCLUDING LOSS OF PROFITS OR REVENUE, LOSS OF USE OF PRODUCTS, LOSS OF DATA, COST
OF CAPITAL, CLAIMS OF CUSTOMERS OF THE END-USER OR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES WHATSOEVER. THE TOTAL CUMULATIVE LIABILITY OF COMPANY HEREUNDER WHETHER
THE CLAIMS ARE BASED IN CONTRACT (INCLUDING INDEMNITY), IN TORT (INCLUDING NEGLIGENCE OR STRICT
LIABILITY) OR OTHERWISE, SHALL NOT EXCEED THOSE SET FORTH ABOVE.
Company shall not be responsible for failure to provide repair or replacement under this Guaranty due to causes
beyond Company’s reasonable control.
END-USER’S OBLIGATIONS: In order to receive the benefits of this Guaranty, the End-User must use the Product in
a normal way; follow the Product’s operation and maintenance manual; and protect against further damage to the
Product if there is a covered defect.
OTHER LIMITATIONS: Company’s obligations under this Guaranty are expressly conditioned upon receipt by
Company of all payments due to it (including interest charges, if any). During such time as Company has not
received payment of any amount due to it for the Product, in accordance with the contract terms under which the
Product is sold, Company shall have no obligation under this Guaranty.
COSTS NOT RELATED TO GUARANTY: The End-User shall be invoiced for, and shall pay for, all services not
expressly provided for by the terms of this Guaranty, including without limitation, site calls involving an inspection
that determines no corrective maintenance is required. Any costs for replacement equipment, installation, materials,
freight charges, travel expenses or labor of Company representatives outside the terms of this Guaranty will be
borne by the End-User.
TO MAKE A CLAIM: In the USA, call the Customer Reliability Center 7x24 at 800-356-5737. Outside of the USA,
contact your local Powerware product sales or service representative, or call the Customer Reliability Center in the
USA at 919-870-3149. For comments or questions about this Load Protection Guaranty, write to the Customer
Quality Representative, 3301 Spring Forest Road, Raleigh, North Carolina 27616 USA.
66
EATON Powerware® 5130 Rack/Tower UPS (1250–3000 VA) User’s Guide S 164201730 Rev 2
www.powerware.com
MAU-00070 AC
*1642017302*
164201730 2
Download PDF