RAIS | Geo | Specifications | RAIS Geo Specifications

ENGLISH
RAIS - manual for Rais Geo
INSTRUCTIONS FOR INSTALLATION,
USE AND MAINTENANCE
RAIS GEO
IMPORTANT INFORMATION
On first lighting the stove you must be careful not to touch the painted
surfaces and it is MOST IMPORTANT that the door is kept slightly ‘ajar’ in
order for the door seal and sealant to cure.
This will prevent the door seal sticking to the painted body and becoming
damaged.
1
ENGLISH
RAIS - manual for Rais Geo
2
ENGLISH
RAIS - manual for Rais Geo
Rais Geo
Revision :
Date
: 2011
INTRODUCTION ...…………………………………………………………..
WARRANTY ..…………………………………………………….…………..
SPECIFICATIONS …………………………………………………………..
CONVECTION ……………………………………………………………….
INSTALLATION INSTRUCTIONS ………………………………….………
CHIMNEY ………………………………………………………….………….
INSTALLATION ……………………………………………………………...
INSTALLATION WITH TURNTABLE ….………………………………….
INSTALLATION DISTANCE TO COMBUSTIBLE WALL ………………
CORNER INSTALLATION 45° …………….……………………………….
INSTALLATION DISTANCE TO NON-COMBUSTIBLE WALL ……….
FOR THE INSTALLER ………………………………………………………
OPERATING INSTRUCTIONS ……………………………………………..
FUEL …………………………………………………………………………...
DRYING AND STORAGE ……………………………………………………
REGULATION OF COMBUSTION AIR ……………………………………
USING THE WOOD BURNING STOVE ……………………………………
ADJUSTMENT OF AIR DAMPER ………………………………………….
CONTROL ……………………………………………………………………..
FIRST USAGE …………………………………………………………………
LIGHTING AND FUELLING …………………………………………………
CLEANING AND CARE ……………………………………………………..
CLEANING OF THE FLUE WAYS …………………………………………
PROBLEM SOLVING ………………………………………………………..
ACCESSORIES AND SPARE PARTS …………………………………….
SPARE PART DIAGRAM RAIS TOPAS …….………...………………….
SPARE PART DIAGRAM RAIS OPUS ……....……………………………
QUICK GUIDE …………………………………………………………………
3
4
4
5
6
7
8-9
10
11-19
20
21
22
23
24
24
25
26
27
27
27
28
29-30
31
32
33
34
34-35
36-37
38
ENGLISH
RAIS - manual for Rais Geo
Introduction
Thank you for purchasing a Rais wood burning stove.
These appliances have been approved by HETAS as
intermittent operating appliances for burning wood logs only.
A Rais wood burning stove is more than just a heat source: it also shows that you care
about design and quality in your home.
To make the most of your wood burning stove it is important that you read the manual
thoroughly before installing and using it.
In the case of warranty coverage, and for general queries regarding your wood
ing stove, it is important that you know the stove’s production number.
We therefore recommend that you note down the number in the table below.
The production number is located in the top of the convection box.
Warranty
Your Rais wood burning stove comes with a 5 year warranty.
The warranty, however, does not cover heat-insulating materials, glass and seals.
These are available to order from your local Rais dealer / stockist.
Any alterations made to the stove will void the warranty.
4
burn-
ENGLISH
RAIS - manual for Rais Geo
Specifications
RAIS GEO 161 RAIS GEO 126
Nominal output (kW):
5
5
3-8
3-8
Approx 100
Approx 100
Size, width/depth/height (mm):
490 / 490 / 1610
490 / 490 / 1260
Combustion chamber width/depth/height (mm).
288 / 288 / 500
288 / 288 / 500
Recommended amount of wood when fuelling (kg)
(Based on 2 - 3 logs of wood approx. 25cm)
1.6
1.6
Min. uptake / Min. draught (Pascal):
-12
-12
Weight (kg):
450
450
79
79
3.95
3.95
5
5
274
274
Min. / Max. output (kW):
Heating area (m2):
Efficiency (%):
Particles after NS3058/3059 (g/kg):
Dust measured according to Din+ (mg/Nm3):
Smoke gas mass flow (g/s):
Smoke gas temperature (°C):
Intermittent operation:
Fuelling should be undertaken
within 3 hours
Please Note, this appliance has been tested by the manufacturers and works on a
3m straight flue.
5
ENGLISH
RAIS - manual for Rais Geo
Convection
Rais stoves are convection stoves. This means that the stove’s back and side panels are
not over-heated. Convection means that there is a circulation of air, which ensures that
the heat is distributed more evenly throughout the entire room. The cold air is sucked in at
the base of the stove and up through the convection channel, which runs along the
stove’s combustion chamber. The heated air comes out at the top of the stove, which
ensures a circulation of warm air throughout the room.
The stoves are equipped with cool door handles - a Rais special feature - which means
you could almost do away with gloves. Be aware, however, that all exterior surfaces
become hot during use - so take extreme care.
6
RAIS - manual for Rais Geo
ENGLISH
Installation Instructions
The following pages give instructions for the safe and proper installation of this heating
appliance in the UK. These instructions cover the basic principles of installation,
although some details may need slight modification to suit particular local site conditions.
In all cases the installation must comply with current UK Building Regulations, Local
Authority Byelaws and other specifications or regulations as they affect the installation of
the stove.
Please note that it is a legal requirement under England and Wales Building Regulations
that the installation of the stove is either carried out under local Authority Building
Control approval or is installed by a Competent Person registered with a Government
approved Competent Persons Scheme. HETAS operate such a scheme and a listing of
their registered Competent Persons can be found on their website at www.hetas.co.uk.
It should be noted that the current Building Regulations requirements are given in
Approved Document J. These requirements may also be met by adopting the relevant
recommendations given in British Standards BS 8303, BS 6461 and BS 7566.
WARNING. Health and Safety Advice Notice.
The installation of this heating appliance is governed by the Health and Safety at Work
Act 1974. it is the responsibility of the installer to ensure that all requirements of this Act
are met during the installation works. Attention is drawn in particular to the following:
Handling:
The appliance is a heavy item and adequate facilities must be available
for loading, unloading and site handling.
Fire Cement: Some types of fire cement are caustic and should not be allowed to come
into contact with the skin. Protective gloves should be worn when
handling fire cement. In case of contact with the skin, wash immediately
with plenty of water.
Asbestos:
This stove contains no asbestos. If there is a possibility of disturbing any
asbestos in the course of the installation, then please seek specialist
guidance and use appropriate protective equipment.
Metal Parts:
When installing or servicing this stove care should be taken to avoid the
possibility of personal injury.
Important Warning - Preparatory Work and safety Checks:
•
•
•
This stove must not be installed into a chimney which serves any other heating
appliance.
There must not be an extractor fan fitted in the same room as the stove, as this can
cause the stove to emit fumes into the room.
If this appliance is installed into an existing chimney, the chimney must first be
swept and examined for soundness and suitability, before the appliance is installed
(see also section headed ‘Chimney’).
7
ENGLISH
RAIS - manual for Rais Geo
Chimney
The chimney is the driving force which makes the stove function. In order for the stove to
perform satisfactorily the chimney height must be sufficient to ensure the correct draught
of 14 to 18 Pa, so as to clear the products of combustion and prevent problems of smoke
leaking into the room when the stove is lit.
Note: A chimney height of not less than 4.5 metres, measured vertically from the outlet of
the stove to the top of the chimney, should be satisfactory.
Alternatively the calculation procedure given in BS 5854:1980 may be used as the basis
for deciding whether a particular chimney design will provide sufficient draught.
Please Note, this appliance has been tested by the manufacturers and works on a 3m
straight flue.
The outlet from the chimney should be above the roof of the building in accordance with
the provisions of the Building Regulations Approved Document J.
If the installation is into an existing chimney, then it must be sound and have no cracks or
other faults which may allow fumes into the house. Older properties, especially, may have
chimney faults or the cross section may be too large i.e. more than 230 x 230mm.
Remedial action should be taken if required, expert advice should be sought where
required.
If the chimney requires lining, then a suitable solid fuel flue liner must be used, in
accordance with Building Regulations Approved Document J.
Any existing chimney must be clear of obstruction and should have been swept clean
immediately before the installation of the stove. If the stove is fitted in place of an open
fire, then the chimney should be swept one month after installation to clear any soot falls
which may have occurred due to the difference in combustion between the stove and the
open fire.
If there is no existing chimney then either a prefabricated block chimney, in accordance
with Building Regulations Approved Document J or a twin wall insulated stainless steel
flue to BS 4543 can be used. These chimneys must be fitted in accordance with the
manufacturer’s instructions and the Building Regulations.
A single wall metal fluepipe is suitable for connecting the stove to the chimney but is
not suitable for using for the complete chimney. The chimney and
connecting fluepipe must have a minimum diameter of 150mm and it’s
dimension should be not less than the size of the outlet socket of the stove which is
150mm. Any bend in the chimney or connecting fluepipe should not exceed 45°. 90°
bends should not be used.
Combustible material should not be located where the heat dissipating through the
walls of fireplaces or flues could ignite it. Therefore when installing the stove in the
presence of combustible materials due account must be taken of the
guidance on the separation of combustible material given in Building Regulations Approved Document J and also in these stove instructions.
8
ENGLISH
RAIS - manual for Rais Geo
If it is found that there is excessive draught in the chimney then either an
adjustable flue damper or alternatively a draught stabiliser should be fitted. The
adjustable flue damper should not close off the flue entirely, but should in its
closed position leave a minimum continuous opening free area of at least 20 %
of the total cross sectional area of the flue or fluepipe.
Adequate provision e.g. easily accessible soot door or doors must be provided
for sweeping the chimney and connecting fluepipe.
You should also familiarise yourself with the draught conditions for chimneys
with 2 flues.
For strong draughts, the chimney or flue should be fitted with a draught
stabiliser. In which case, it is important to ensure that there is a free flow-through
area of minimum 20 cm2 when the regulating gate is shut. Otherwise, the fuel
energy may not be used optimally.
If, at any time, you are unsure about the condition of the chimney, you should
contact a chimney sweep.
Remember that access to the soot door should be kept clear.
9
ENGLISH
RAIS - manual for Rais Geo
Installation
It is prohibited to carry out unauthorised alterations to the stove.
There must be plenty of fresh air in the room where the stove is being installed, in order to
ensure proper combustion. Note that any mechanical exhaust ventilation - e.g. an
extraction hood - may reduce the air supply. Any air grilles must be placed in such a
manner, that the air supply is not blocked.
The stove is equipped with four convection air outlets, which may be connected with
suit-able air ducts to other rooms.
Building Regulations Approved Document J gives specific guidance on the required
permanent ventilation into the room for combustion air of solid fuel appliances.
The floor structure must be able to carry the weight of the wood burning stove, as well as
the weight of a chimney, if necessary.
When you choose where to set up your RAIS wood burning stove, you should consider the
heat distribution to the other rooms. This will enable you to get the best use out of your
stove.
The stove should be set up at a safe distance from inflammable materials.
See the manufacturer's plate on the wood burning stove.
10
ENGLISH
RAIS - manual for Rais Geo
11
ENGLISH
1
2
RAIS - manual for Rais Geo
Locate the stove where it is to be installed, it cannot be moved once the
soapstone has been installed.
A
The rear flue connection can be installed after the third row of soapstone
has been positioned ( Geo 161 only ).
B
For top flue connection, remove the marked opening with a plastic or
rubber hammer.
C
Installation up to the ceiling, the easiest option is to use the Rais sliding
flue system and adaptor. The steel top plate should be pushed onto the
flue pipe.
Adjust the legs so that they are level.
- Loosen the counter screw.
- Adjust the leg.
- Tighten the counter screw.
3
Position the soapstone as shown on the diagram and screw them together
with the enclosed mountings.
Depending on the choice of flue outlet, you are left with one piece of
soapstone, either number 7023 or 7033/7036.
4
Insert the firebox.
A
Ensure that the firebox is centred within the stove body, it must NOT
touch the soapstone.
B
If you are using the rear flue outlet option, ensure that the exit holes are
aligned.
12
ENGLISH
RAIS - manual for Rais Geo
5
With an external air connection;
Mount the air supply at the bottom of the stove with a flexible hose and a
clamp.
6
Without an external air connection;
Fit the vent grille ( see step 5 on page 16 )
13
ENGLISH
RAIS - manual for Rais Geo
14
ENGLISH
RAIS - manual for Rais Geo
15
ENGLISH
RAIS - manual for Rais Geo
16
ENGLISH
RAIS - manual for Rais Geo
17
ENGLISH
RAIS - manual for Rais Geo
18
ENGLISH
RAIS - manual for Rais Geo
19
ENGLISH
RAIS - manual for Rais Geo
Installation distance in case of combustible wall
To find out whether the wall next to where the stove is going to be installed is flammable,
you should contact your building contractor or the local building authorities.
The hearth should be able to accommodate the weight of the stove. The chimney must be
independently supported by wall brackets or a ceiling support plate. The weight of the stove
is indicated in the brochure.
The stove should always be installed on a non-combustible hearth of a size and construction
that is in accordance with the provisions of the current UK Building Regulations Approved
Document J.
If the stove is to be installed on a wooden floor, it must be covered with a non-combustible
material at least 12mm thick, in accordance with UK Building Regulations Approved
Document J, to a distance of 300 mm in front of the stove and 150 mm to each side
measuring from the door of the combustion chamber.
The clearance distances to combustible material beneath, surrounding or upon the hearth
and walls adjacent to the hearth should comply with the guidance on the separation of
combustible material given in UK Building Regulations Approved Document J and also in
20
ENGLISH
RAIS - manual for Rais Geo
21
ENGLISH
RAIS - manual for Rais Geo
Installation distance for non-combustible walls
We recommend a minimum distance to non-combustible material of 50mm for cleaning
considerations.
22
ENGLISH
RAIS - manual for Rais Geo
For the Installer
Finally before firing the stove for the first time a check should be made to ensure that the
assembly and stove installation has been satisfactory and that there are no leaks in any
seals in the appliance and appliance connections to the chimney.
Ensure that the appliance and chimney flue are functioning correctly before finally
handing over to the user. Read the later parts of this manual for guidance on care
required when first lighting.
Inform the user that the appliance has been commissioned and ready to use and give
instruction on the safe operation of the stove.
These Instructions must be left with the user and the user should be instructed to keep
them in a safe place.
23
ENGLISH
RAIS - manual for Rais Geo
Operating instructions
Please note that HETAS Appliance Approval only covers the use of dry seasoned wood
logs on this appliance. HETAS Approval does not cover the use of other fuels either
alone or mixed with the wood logs, nor does it cover instructions for the use of other
fuels.
Fuel
The stove is designed and approved in accordance with EN 13240 and NS 3058 for
stoking split, dried firewood. The firewood must have a water content of 15-22% and its
max. length should be the length of the combustion chamber minus 50-60 mm.
Stoking with wet firewood causes both soot, environmental pollution and bad fuel
economy. Freshly cut wood contains approx. 50-70% water and is thoroughly unsuitable
for stoking. Allow at least 1 year of storage time for newly cut wood before using. Wood
with a diameter of more than 100 mm should be split. Regardless of wood size, it should
always have at least one surface area free of bark.
We do not recommend stoking with painted, laminated or impregnated wood, wood with
a synthetic surface, painted refuse wood, chipboard, plywood, domestic waste, paper
bri-quettes and pit coal, as this will produce malodorous smoke, which could be
poisonous.
When firing with the above-mentioned items and amounts larger than those
recommended, the stove is subjected to a larger amount of heat, which results in a
higher chimney temperature and lower efficiency. This can result in the stove and
chimney becoming damaged and would void the warranty.
The calorific value of the firewood is closely connected to the moisture level.
Moist firewood has a low heat value. The more water the wood contains, the more
energy it takes for this water to vaporise, resulting in this energy being lost.
ONLY USE RECOMMENDED FUELS
The following table shows the calorific value of different types of wood, which have been
stored for 2 years and which have a residual moisture of 15 - 17%.
Wood
Hornbeam
Beech and oak
Ash
Maple
Birch
Mountain pine
Fir
Poplar
Kg dry wood pr m3
640
580
570
540
510
480
390
380
compared to beech/oak
110%
100%
98%
93%
88%
83%
67%
65%
1kg of wood yields the same heat energy irrespective of wood type.
1kg of beech merely takes up less space than 1kg of fir.
24
ENGLISH
RAIS - manual for Rais Geo
Drying and storage
Drying wood takes time: proper air drying takes approximately 2 years.
Here are some tips:
Store the wood sawn, split and stacked in an airy, sunny place, which is protected against
rain (the south side of the house is particularly suitable).
Store the firewood stacks at a hand's breadth apart, as this ensures that the air flowing
through takes the moisture with it. Avoid covering the firewood stacks with plastic, as this
prevents the moisture from escaping. It is a good idea to bring the firewood into the house
2-3 days before you need it.
25
ENGLISH
RAIS - manual for Rais Geo
Regulating the combustion air
All RAIS stoves are equipped with a one-handed operating lever for regulating the damper.
The stove-specific regulating mechanisms can be seen on the diagrams.
Primary air is the combustion air added to the primary combustion zone, i.e. the bed of
glowing embers. This air, which is cold, is only used in the lighting stage. Secondary air is
the air which is added in the gas combustion zone, i.e. air which contributes to the
combustion of the pyrolysis gasses (preheated air, which is used for the cleaner glass
system and combustion). This air is sucked through the damper under the combustion
chamber and is pre-heated through the side channels and then emitted as hot scavenging
air onto the glass. The hot air rinses the glass and keeps it soot-free.
The tertiary channel, which can be seen at the top of the combustion chamber towards the
back, serves to combust the final gas residues.
By setting the interval between position 1 and 2, the energy content in the firewood is used
optimally, as there is oxygen for combustion and for the burning of the pyrolysis gasses.
When the flames are a clear yellow the damper has been set correctly. Finding the correct
position comes with time after you have used for stove for a while.
It is not recommended that you turn it down completely. A mistake commonly made is
shutting the damper too early because it feels too hot. This results in dark smoke emanating
from the chimney and in the calorific value of the firewood not being used to its fullest.
Room ventilation and stoves
There must not be an extractor fan fitted in the same room as the stove as this can cause
the stove to emit smoke and fumes into the room.
The stove requires a permanent and adequate air supply in order for it to operate safely and
efficiently.
In accordance with current Building Regulations the installer may have fitted a permanent air
supply vent into the room in which the stove is installed to provide combustion air. This air
vent should not under any circumstances be shut off or sealed.
26
ENGLISH
RAIS - manual for Rais Geo
Using the wood burning stove
Adjusting the air damper.
The damper has 3 settings.
Position 1
The damper is closed meaning that there is no air
supply.
Position 2
Push the handle to the left, to the first mark.
This position gives full secondary air.
During normal use the lever is set between position 1
and 2.
When the flames are clear and yellow, the damper is set
correctly, i.e. resulting in a slow/optimal burning.
Position 3
Push the handle to the left to the stop.
The air damper is completely open and gives full primary
and secondary air. This position is for the lighting stage
and is not used under normal operation.
Control
If the ash is white and the walls in the combustion chamber are soot free after the stove
has been used, the air regulation was set correctly and the wood was sufficiently dry.
27
ENGLISH
RAIS - manual for Rais Geo
First usage
A careful start pays off. Start with a small fire, so that the wood burning stove can get
accustomed to the high temperature. This gives the best start and any damage is
avoided.
Be aware that a strange but harmless odour and smoke concoction may emanate from
the surface of the stove, the first time you fire up. This is because the paint and
materials need to harden. The odour disappears quickly, but you should check the
ventilation and draught, if possible. See also, the IMPORTANT warning notice below
about persistent fumes.
During this process you must be careful not to touch the painted surfaces, it is
recommended that you regularly open and close the door to prevent the door seal from
sticking.
The stove may also produce "clicking noises" during heating and cooling, caused by the
large temperature differences which the material is subjected to.
Never use any type of liquid fuel for kindling or maintaining the fire. You could be at risk
of explosion.
The stove gets very hot when in use, always wear protective gloves when tending the
stove.
If the stove has not been used for a while, follow the steps as if you were using it for the
first time.
IMPORTANT - Warning Note!
Properly installed, operated and maintained this appliance will not emit fumes into the
dwelling. Occasional fumes from de-ashing and re-fuelling may occur.
However, persistent fume emission is potentially dangerous and must not be tolerated.
If fume emission does persist, the following immediate actions should be taken:
(a)
(b)
(c)
(d)
Open doors and windows to ventilate room.
Let the fire out or eject and safely dispose of fuel from the appliance.
Check for flue or chimney blockage, and clean if required.
Do not attempt to relight the fire until the cause of the fume emission has been
identified and corrected. If necessary seek expert advice.
IMPORTANT - Warning Note!
Do not use an aerosol spray on or near the stove when it is alight.
IMPORTANT - Safety advice!
When using the stove in situations where children, aged and/or infirm persons are
present a fireguard must be used to prevent accidental contact with the stove. The
fireguard should be manufactured in accordance with BS 8423:2002 (Replaces BS
6539).
28
ENGLISH
RAIS - manual for Rais Geo
Lighting and fuelling
To light the stove, use alcohol briquettes or
similar, as well as approximately 2kg of
firewood, split into kindling sticks. Set the air
damper to the fully open position.
Tips before firing up:
Open a door or window close to the wood
burning stove.
If there is ‘storm’ in the stove coming from
the chimney it is advisable to place a
screwed up piece of newspaper between
the upper baffle plate and the chimney.
Light the paper and wait until you hear a
‘rumbling’ noise in the chimney. This means
that there is definitely a draught in the
chimney and you should avoid smoke
coming back into the room.
Light the fire and shut the
door, leave the door ajar
approximately 10-15mm.
29
ENGLISH
RAIS - manual for Rais Geo
When the flames are clear, after approximately 5-10
minutes, close the door.
Damper - see adjustment of the damper.
After approximately 10-20 minutes, when you have a
good bed of glowing embers, add 2-3 pieces of wood.
Leave the door ajar until the fire has caught properly,
then close the door.
Damper - see adjustment of the damper.
After approximately 5 minutes, or when the flames are
clear and stable, close the damper gradually.
It is recommended to have a layer of approximately
20mm, as it has an insulating effect.
NOTE!
During operation the
door should always
remain closed.
30
ENGLISH
RAIS - manual for Rais Geo
Cleaning and care
The wood burning stove and the chimney must be serviced by a chimney sweep twice a
year.
During cleaning and care, the stove must be cold.
If the glass is sooty:
- Moisten a piece of paper or newspaper, dip it in the ash, and rub the sooty glass with it.
- Now rub with a dry piece of paper and the glass will become clean.
- As an alternative you can use glass cleaner, which you can buy from you RAIS
distributor.
Clean the exterior with a dry sponge or a soft brush.
Cleaning the combustion chamber:
Scrape/shovel the ash out and store it in a non-flammable container until it has cooled
down. You can dispose of ash with your normal household waste or recycle on the
garden.
REMEMBER!!
Never remove all the ashes from the combustion chamber - the wood will burn at its best
with a layer of ashes of approx. 20 mm.
Prolonged periods of non-use:
If the stove is to be left unused for a prolonged period of time then it should be given a
thorough clean to remove ash and unburned fuel residues. To enable a good flow of air
through the appliance to reduce condensation and subsequent damage, leave the air
controls fully open.
Prior to a new heating season, it should be checked that the chimney and flue pipe
connector are not blocked.
31
ENGLISH
RAIS - manual for Rais Geo
Cleaning the flue ways
The fixing clips are pushed up and removed from the
skamol on the side.
The fixing clips are positioned in the top right corner
of the firebox.
The picture on the left is a detailed view of the top
right corner of the firebox.
This is a close up view of the area is marked by a
circle in the next picture.
The baffle plate is pulled forwards and then
tipped down towards the firebox.
Note, the skamol on the sides are now loose.
The smoke connector is located above the baffle.
The picture on the left is taken from the bottom of the
firebox looking up.
The smoke connector is lifted free from the anchor
bolts and lowered at an angle towards the firebox.
Now there is a clear view of the flue.
Remove dirt and dust, then replace all of the parts in
reverse order.
32
ENGLISH
RAIS - manual for Rais Geo
Problem solving
Smoke spillage around door:
- could be due to too low draught in the chimney <12Pa
- check if the flue or chimney is blocked
- check if a extraction hood is switched on; if it is, switch it off and open a window/door in
the proximity of the stove for a short while.
Soot on glass:
- could be because the firewood is too wet.
- make sure that the stove is heated properly when firing up, prior to closing the door
- could be because the damper regulation is too low.
A stove burning too strong could be caused by:
- a leak around the door seal
- chimney draught too large >22 Pa, draught control regulator should be installed.
A stove burning too weakly could be caused by:
- too little firewood
- too little air supply for the room ventilation
- dirty smoke channels
- leaking chimney
- leakage between chimney and flue
If your stove continues to malfunction, we recommend that you contact your RAIS
distributor or chimney sweep.
IMPORTANT!!
To ensure safe burning there must be clear yellow flames or clear embers at all times. The
firewood should not be smouldering. Therefore you should never completely cut off the air
supply.
WARNING!!
In case of chimney fire:
- shut off all air supply on the wood burning stove
- contact the fire services
- never attempt to put out fire with water!
- afterwards, you should ask your chimney sweep to check the stove and chimney
33
ENGLISH
RAIS - manual for Rais Geo
Accessories and spare parts
If spare parts other than those recommended by RAIS are used, the warranty is voided.
All replacement spare parts can be purchased from your RAIS distributor / stockist.
See the following spare parts diagrams for the individual products.
34
ENGLISH
RAIS - manual for Rais Geo
35
ENGLISH
RAIS - manual for Rais Geo
36
ENGLISH
RAIS - manual for Rais Geo
37
ENGLISH
RAIS - manual for Rais Geo
38
ENGLISH
RAIS - manual for Rais Geo
39
ENGLISH
RAIS - manual for Rais Geo
40
ENGLISH
RAIS - manual for Rais Geo
41
ENGLISH
RAIS - manual for Rais Geo
U K Distributor.
Robeys Ltd.
Riverside, Goods Road, Belper,
Derbyshire, England. DE56 1UU
Tel: 01773 820940 Fax: 01773 820477
E Mail: info@robeys.co.uk
www.robeys.co.uk
June 2011
42
Download PDF