Datalogic | PowerScan D8330 | Technical data | Datalogic PowerScan D8330 Technical data

PowerScan™ D8330 Reader
Industrial Handheld Laser Bar Code Reader
Quick Reference Guide
Datalogic ADC, Inc.
959 Terry Street
Eugene, OR 97402
USA
Telephone: (541) 683-5700
Fax: (541) 345-7140
©2007-2014 Datalogic, Inc.
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted
in any form or by any means without prior written permission of Datalogic ADC,
Inc. or its subsidiaries or affiliates ("Datalogic" or "Datalogic ADC"). Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce
and transmit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices
appear on any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contacting your Datalogic representative. Electronic versions may either
be downloadable from the Datalogic website (www.datalogic.com) or provided on
appropriate media. If you visit our website and would like to make comments or
suggestions about this or other Datalogic publications, please let us know via the
"Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual
that is complete and accurate, however, Datalogic reserves the right to change any
specification at any time without prior notice.
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in
many countries, including the U.S.A. and the E.U. All other brand and product
names may be trademarks of their respective owners.
Patents
This product may be covered by one or more of the following patents:
Design Pat. AU 310201; AU 310202; CN 693980; CN735959; HK 0602013.5M001; HK
0602013.5M002; JP 1305693; KR 30-0460940; US D570,843 S; USD588,596 S.
US Pat. 5,992,740; 6,305,606 B1; 6,517,003; 6,808,114 B1; 6,997,385 B2; 7,387,246 B2;
5,367,151; 5,449,893; 5,545,889; 6,098,877; 6,220,514 B1; 6,412,698 B2; 6,607,132 B1;
6,817,529 B2; 6,834,805 B2; 7,948,214 B2.
European Pat. 789,315 B1; 895,175 B1; 1,128,314 B1; 1,128,315 B1; 1,396,811 B1;
1,413,971 B1; 1,816,585 B1; 1,942,442 B1.
Additional patents pending.
Table of Contents
END USER LICENSE AGREEMENT .................................................................................................. iii
Software Product Policy .................................................................................................................... v
Customers Under Software Support ................................................................................. v
Using the PowerScan™ PD8300 ..................................................................................................... 1
Aiming System .......................................................................................................................... 1
Setting Up the Reader ....................................................................................................................... 2
Connecting the Cable ............................................................................................................. 2
Connecting to the Host Interface ....................................................................................... 3
Selecting the Interface Type ............................................................................................................ 4
Interface Selection ................................................................................................................... 4
Keyboard Nationality .............................................................................................................. 6
Programming ........................................................................................................................................ 8
Restore Default .......................................................................................................................... 8
Data Format Terminators ...................................................................................................... 8
Operating Test ........................................................................................................................... 8
Technical Features .............................................................................................................................. 9
Default Values .....................................................................................................................................10
Compliance ..........................................................................................................................................11
Laser Safety Compliance ......................................................................................................11
LED CLASS .................................................................................................................................12
CE Compliance ........................................................................................................................12
FCC Compliance ......................................................................................................................12
Power Supply ...........................................................................................................................12
China RoHS Table of Restricted Elements .......................................................... 13
WEEE Compliance ..................................................................................................................14
Datalogic ADC Limited Factory Warranty ......................................................................15
Ergonomic Recommendations .....................................................................................................16
Services and Support .......................................................................................................................17
Quick Reference Guide
i
NOTES
ii
PowerScan™ PD8300
Datalogic ADC, Inc.
PowerScan™ 8300 PRODUCT SERIES
END USER LICENSE AGREEMENT
Notice to End User: The Datalogic Product you have acquired contains embedded Software, which is integral to
the product's operation. This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the Datalogic Product, you will be deemed to have accepted the terms and
conditions of this Agreement. If you do not intend to be bound to the terms of this Agreement, Datalogic is not
willing to license the Software to you, you may not use the Datalogic Product or the Software, and you must
contact the party from whom you acquired the Datalogic Product for instructions.
This End User Software License Agreement ("Agreement") is a legally binding agreement governing the licensing of the Software and Documentation by Datalogic ADC, Inc. and its Affiliates ("Datalogic") to the entity or
person who has purchased or otherwise acquired a Datalogic Product ("End User"). For purposes of this Agreement, any software that is associated with a separate end-user license agreement is licensed to you under the
terms of that license agreement. Datalogic and End User hereby agree as follows:
1. Definitions
1.1 "Affiliate" means a business entity currently existing or later acquired that controls, is controlled by, or is
under common control with Datalogic S.p.A.
1.2 "Documentation" means materials such as user's guides, program reference guides, quick reference guides,
manuals, or similar materials associated with or related to the Datalogic Product, whether in printed,
"online", or other form.
1.3 "Proprietary Information" means: (a) source code, object code, software, documentation, and any related
internal design, system design, data base design, algorithms, technology, technical data or information,
implementation techniques, and trade secrets related to the Software, (b) any other trade secrets marked
appropriately or identified as proprietary or confidential, and (c) any information that End User, under the
circumstances, should recognize as confidential. Proprietary Information does not include any information that the receiving party can establish was (1) in the public domain, (2) already in the receiving party's
possession or rightfully known prior to receipt, (3) rightfully learned from a third party not in violation of
any other's proprietary rights, or (4) independently developed without access to Proprietary Information.
1.4 "Datalogic Product" means the Datalogic® Powerscan™ series scanner product, including all embedded
Software in and all Documentation related to such product, which has been purchased or otherwise
acquired by End User, whether obtained directly or indirectly from Datalogic.
1.5 "Software" means any software or computer programs of Datalogic or its third party licensors in machine
readable form which is embedded in the Datalogic Product, whether obtained directly or indirectly from
Datalogic, including any replacement, update, upgrade, enhancement or modification.
2. Scope Of License Granted
2.1 Datalogic grants to End User a non-exclusive, non-transferable, perpetual license to use the Software,
solely on the Datalogic Product in which it is embedded ("designated Datalogic Product"), in machinereadable form only, solely for End User's internal business purposes. This Agreement does not convey
ownership of the Software to End User. Title to the Software shall be and remain with Datalogic or the
third party from whom Datalogic has obtained a licensed right. As used in this Agreement, the term "purchase" or its equivalents when applied to the Software shall mean "acquire under license." End User is not
entitled to receipt or use of the source code to any Software.
2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise reproduce or
remanufacture the Software, whether modified or unmodified, nor sell, assign, sublicense, distribute, lend,
rent, give, or otherwise transfer the Software to any other person or organization, for purposes other than
as expressly provided in this Agreement, without Datalogic's prior written consent.
3. Transfers, Support
3.1 Any copying, installing, reproduction, remanufacture, reverse engineering, electronic transfer, or other use
of the Software on other than the designated Datalogic Product will be a material breach of this Agreement. However, Datalogic may elect not to terminate this Agreement or the granted licenses, but instead
may elect to notify End User that End User is deemed to have ordered and accepted a license for each
breaching use. End User shall pay Datalogic the applicable list price for such licenses as of the date of
such breach.
3.2 End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Datalogic
Product to any third party unless such third party agrees with Datalogic in writing to be bound by the
terms and conditions of this Agreement. Any such transfer of the Datalogic Product absent such agreement shall be null and void.
3.3 End User may obtain support for Software from Datalogic at Datalogic's standard support fees and under
Datalogic's standard support terms and conditions in effect at the time the support is requested.
4. Intellectual Property
End User acknowledges that the Software constitutes valuable trade secrets of Datalogic or Datalogic's third
party licensors and that the Software is protected by intellectual property laws and treaties. The license set
forth in this Agreement does not transfer to End User any ownership of Datalogic's or its third party licensors'
copyrights, patents, trademarks, service marks, trade secrets, or other intellectual property rights and End
User shall have no right to commence any legal actions to obtain such rights. End User shall not remove, modify, or take any other action that would obscure any copyright, trademark, patent marking, or other intellectual
property notices contained in or on the Datalogic Product.
5. Proprietary Information
5.1 End User acknowledges that Proprietary Information is the confidential, proprietary, and trade secret
Quick Reference Guide
iii
END USER LICENSE AGREEMENT
property of Datalogic and Datalogic's third party licensors and End User acquires no right or interest in any
Proprietary Information.
5.2 End User shall not disclose, provide, or otherwise make available the Proprietary Information of Datalogic
or its third party licensors to any person other than End User's authorized employees or agents who are
under confidentiality agreement, and End User shall not use the Proprietary Information other than in
conjunction with use of the Datalogic Product exclusively for End User's internal business purposes. End
User shall take steps to protect the Proprietary Information no less securely than if it were End User's own
intellectual property.
5.3 The provisions of this Proprietary Information Section shall survive and continue for five (5) years after the
termination of this Agreement.
6. Limited Warranty
6.1 Datalogic warrants that, under normal use and operation, the Datalogic Product will conform substantially
to the applicable Documentation for the period specified in the Documentation. During this period, for all
reproducible nonconformities for which Datalogic has been given written notice, Datalogic will use commercially reasonable efforts to remedy nonconformities verified by Datalogic. End User agrees to supply
Datalogic with all reasonably requested information and assistance necessary to help Datalogic in remedying such nonconformities. For all defects reported to Datalogic within the warranty period, Datalogic's
liability is limited to providing End User with one copy of corrections or responding to End User's problem
reports according to Datalogic's standard assistance practices. Datalogic does not warrant that the product will meet End User's requirements or that use of the product will be uninterrupted or error free, or that
Datalogic's remedial efforts will correct any nonconformance. This limited warranty does not cover any
product that have been subjected to damage or abuse, whether intentionally, accidentally, or by neglect, or
to unauthorized repair or unauthorized installation, and shall be void if End User modifies the product,
uses the product in any manner other than as established in the Documentation, or if End User breaches
any of the provisions of this Agreement.
6.2 EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DATALOGIC PRODUCT IS PROVIDED "AS IS" AND DATALOGIC MAKES NO WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WRITTEN OR ORAL, WITH RESPECT
TO THE PRODUCT, AND SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
7. Infringement
7.1 Datalogic will defend End User against any claim in a lawsuit that the Datalogic Product furnished hereunder infringe a United States patent or copyright of a third party and Datalogic will pay any damages
finally awarded against End User by a court of competent jurisdiction that are attributable to such claim
or will pay End User's part of any settlement that is attributable to such claim, provided, that 1) End User
notifies Datalogic promptly in writing of the claim, 2) Datalogic controls the defense or settlement of the
claim, and 3) End User cooperates fully with Datalogic in such defense or settlement. All notices of a claim
should be sent to Datalogic ADC, Inc., Legal Department, 959 Terry Street, Eugene, OR 97402.
7.2 In the defense or settlement of any such claim, Datalogic may, at its option, 1) procure for End User the
right to continue using the Datalogic Product, 2) modify the Datalogic Product so that it becomes noninfringing, 3) replace the Datalogic Product with an equivalent product not subject to such claim, or 4) provide End User an opportunity to return the Datalogic Product and receive a refund of the purchase price
paid, less a reasonable allowance for use.
7.3 Datalogic shall have no liability to End User for claims of infringement based upon 1) the use of any Datalogic Product in combination with any product which Datalogic has not either furnished or authorized for
use with such Datalogic Product 2) the use of any Datalogic Product designed, manufactured, or modified
to the specifications of End User, or 3) End User's modification of the Datalogic Product without written
authorization from Datalogic.
7.4 THE FOREGOING STATES DATALOGIC'S COMPLETE AND ENTIRE OBLIGATION CONCERNING CLAIMS OF
PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY INFRINGEMENT, CANCELS AND SUPERCEDES
ANY PRIOR AGREEMENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES CONCERNING SUCH
CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CONTEMPORANEOUS, OR FUTURE
AGREEMENTS OR DEALINGS BETWEEN THE PARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET
FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES.
8. Limitation Of Liability
EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END USER
BY ANY OTHER PARTY. IN NO EVENT SHALL DATALOGIC'S LIABILITY FOR DAMAGES, IF ANY, WHETHER BASED
UPON CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIABILITY, WARRANTY, OR ANY
OTHER BASIS, EXCEED THE PRICE OR FEE PAID BY END USER FOR THE DATALOGIC PRODUCT. UNDER NO CIRCUMSTANCES SHALL DATALOGIC BE LIABLE TO END USER OR ANY THIRD PARTY FOR LOST PROFITS, LOST
DATA, INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANY OTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT, INCIDENTAL, PUNITIVE, EXEMPLARY, OR OTHER SIMILAR DAMAGES, EVEN IF DATALOGIC HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
9. Government Restricted Rights; International Use
9.1 Use, duplication, or disclosure of the Software by the U.S. Government is subject to the restrictions for
computer software developed at private expense as set forth in the U.S. Federal Acquisition Regulations
at FAR 52.227-14(g), or 52.227-19 or in the Rights in Technical Data and Computer Software clause at
DFARS 252.227-7013(c)(1)(ii), whichever is applicable.
9.2 If End User is using the Datalogic Product outside of the United States, End User must comply with the
applicable local laws of the country in which the Datalogic Product is used, with U.S. export control laws,
and with the English language version of this Agreement. The provisions of the "United Nations Convention on International Sale of Goods" shall not apply to this Agreement.
iv
PowerScan™ PD8300
Software Product Policy
10. Termination
10.1Either party may terminate this Agreement or any license granted under this Agreement at any time upon
written notice if the other party breaches any provision of this Agreement.
10.2Upon termination of this Agreement, End User immediately shall cease using any nonembedded software
and shall return to Datalogic or destroy all non-embedded software covered by this Agreement, and shall
furnish Datalogic with a certificate of compliance with this provision signed by an officer or authorized
representative of End User. For embedded software, End User agrees to sign a waiver prepared by Datalogic concerning further use of the embedded Software. End User's resumed or continued use of the
embedded Software after termination shall constitute End User's agreement to be bound by the terms
and conditions of this Agreement for such use.
11. General Provisions
11.1 Entire Agreement; Amendment. This document contains the entire agreement between the parties relating to the licensing of the Software and supersedes all prior or contemporaneous agreements, written or
oral, between the parties concerning the licensing of the Software. This Agreement may not be changed,
amended, or modified except by written document signed by Datalogic.
11.2 Notice. All notices required or authorized under this Agreement shall be given in writing, and shall be
effective when received, with evidence of receipt. Notices to Datalogic shall be sent to the attention of
Contract Administration, Datalogic ADC, Inc., 959 Terry Street, Eugene, OR 97402, or such other address as
may be specified by Datalogic in writing.
11.3 Waiver. A party's failure to enforce any of the terms and conditions of this Agreement shall not prevent
the party's later enforcement of such terms and conditions.
11.4 Governing Law; Venue: This Agreement and the rights of the parties hereunder shall be governed by and
construed in accordance with the laws of the State of Oregon U.S.A, without regard to the rules governing
conflicts of law. The state or federal courts of the State of Oregon located in either Multnomah or Lane
counties shall have exclusive jurisdiction over all matters regarding this Agreement, except that Datalogic
shall have the right, at its absolute discretion, to initiate proceedings in the courts of any other state,
country, or territory in which End User resides, or in which any of End User's assets are located.
11.5 Attorneys' Fees. In the event an action is brought to enforce the terms and conditions of this Agreement,
the prevailing party shall be entitled to reasonable attorneys' fees, both at trial and on appeal.
- END -
Software Product Policy
Datalogic reserves the right to ship its products with the latest version of software/firmware available. This provides our customers with the very latest in Datalogic software technology.
The only exception to this policy is when the buyer has a signed contract with Datalogic that clearly
defines the terms and conditions for making software/firmware changes in products shipped to the
buyer.
Customers Under Software Support
Customers that elect to subscribe to Datalogic Software Maintenance and Support Agreement will
receive 30 days advance notification of: (1) the release of a new software version; and/or (2) discontinuation of any prior software version that will no longer be supported. Datalogic will provide maintenance for a fee that will assist customers in transitioning to the next software version. If a customer
is currently using the software version being discontinued, the customer may elect to transition to
any one of the newer versions, depending on the hardware in use.
To arrange for a Software Maintenance and Support Agreement please contact your Datalogic sales
person.
Quick Reference Guide
v
Software Product Policy
NOTES
vi
PowerScan™ PD8300
PowerScan™ PD8300
Using the PowerScan™ PD8300
PowerScan™ PD8300 readers automatically scan barcodes at a distance. Simply
aim and pull the trigger. Code scanning is performed along the scan line emitted
from the reading window. This line must cross the entire code. The best reading
angles are indicated in the figure below.:
Aiming System
The PowerScan™ PD8300 provides an aiming system. If enabled, a partial trigger
press produces a red spot, which should be aimed over the code center to get the
best reading performance, see figure (1) above. By completely pressing the trigger
the scan line appears to start code scanning (2).
After setting up the reader, you can enable or disable the aiming system by reading
the codes below:
Disable Aiming System (Default)
Ì$+Bj0$-"Î
Enable Aiming System
Ì$+Bj1$-'Î
Quick Reference Guide
1
Setting Up the Reader
Setting Up the Reader
Follow the steps below to connect and get your reader up and communicating with
its host.
1.
2.
Connect the Cable to the reader and the Host.
Configure the Interface (see page 4).
3.
Program the Reader starting on page 8 (optional, as needed).
Connecting the Cable
A. Rubber gasket
B. Plastic boot
C. Cable spacer
D. Cover
E. Strain relief
2
1.
2.
Slip the cover over the cable.
Push the plastic boot into the rubber gasket. Take care that the tab
on the plastic boot is aligned with
the notch in the rubber gasket.
3.
Push the plastic boot and gasket
into the handle. Ensure that the
“Front” marking on the plastic
boot is facing out, with the arrow
pointing towards the front of the
scanner.
4.
Insert the cable into the socket of
the plastic boot.
5.
Insert the cable spacer into the
cable wire and slide it towards the
handle.
6.
Push the cover along the cable
towards the reader, and hook it
over the yellow “tooth”.
7.
Insert the strain relief into the
cover and tighten the screw to fix
the whole assembly to the reader
handle.
Align
Notch
Arrow
Tab
PowerScan™ PD8300
Setting Up the Reader
Connecting to the Host Interface
USB
WEDGE
RS-232
PEN
Quick Reference Guide
3
Selecting the Interface Type
Selecting the Interface Type
Upon completing the physical connection between the reader and its host, proceed
directly to Interface Selection below for information and programming for the interface type the reader is connected to (for example: RS-232, Keyboard Wedge,
USB, etc.) and scan the appropriate barcode to select your system’s correct interface
type.
Interface Selection
Select one of the interface codes according to your application.
USB Interface Selection
USB-KBD
Ì$+UA03$-:Î
USB-KBD-ALT-MODE
Ì$+UA04$-@Î
USB-COM*
Ì$+UA02$-4Î
USB-IBM-Hand Held
Ì$+UA01$-.Î
USB-IBM Table top
Ì$+UA00$-(Î
USB KBD-APPLE
Ì$+UA05$-FÎ
* When configuring USB-COM, the relevant files and drivers must be installed from the USB
Device Installation software. Go to www.datalogic.com.
4
PowerScan™ PD8300
Selecting the Interface Type
Pen Emulation Interface Selection
PEN
Ì$+CP6$-BÎ
RS-232 Interface Selection
RS-232 Standard
Ì$+CP0$-$Î
Nixdorf Mode A
Ì$+CM2EC0$->Î
Fujitsu
Ì$+CM1$-ÈÎ
ICL Mode
Ì$+CM0$-ÃÎ
Wedge Interface Selection
Wedge IBM AT or PS/2 PCs
Ì$+CP500$-aÎ
PC Notebook
Ì$+CP505$-ÈÎ
PC Notebook - ALT mode
Ì$+CP508$-2Î
IBM AT - ALT mode
Ì$+CP507$-+Î
The Interface for IBM XT and IBM Terminals 3151, 347X and 348X can be selected from the PowerScan™ PD8300 Reference Manual available online at
www.datalogic.com.
Quick Reference Guide
5
Selecting the Interface Type
Keyboard Nationality
USB-KBD and Wedge users should select one of the following wedge keyboard nationality codes according to the keyboard.
Belge
Ì$+FJ7$-8Î
Deutsch
Ì$+FJ3$-$Î
English
Ì$+FJ4$-)Î
Español
Ì$+FJ6$-3Î
Français
Ì$+FJ2$-ÊÎ
Italiano
Ì$+FJ1$-ÅÎ
Svenskt
Ì$+FJ5$-.Î
USA (Default)
Ì$+FJ0$-|Î
6
PowerScan™ PD8300
Selecting the Interface Type
Keyboard Nationality (continued)
The following Keyboard Nationality selections are only valid for IBM AT compatible PCs:
Japanese
Ì$+FJ8$-=Î
Russian (Latin)
Ì$+FJ9$-BÎ
Russian (Cyrillic)
Ì$+FJA$-jÎ
Hungarian
Ì$+FJB$-oÎ
Slovenian, Croatian, Serbian (Latin)
Ì$+FJC$-tÎ
Romanian
Ì$+FJD$-yÎ
Czech Republic
Ì$+FJE$-~Î
Quick Reference Guide
7
Programming
Programming
The reader is factory-configured with a set of standard default features. After scanning the interface barcode from the Interfaces section, select other options and customize your reader through use of the programming barcodes available in the
PowerScan™ PD8300 Reference Manual. Check the corresponding features section for your interface, and also the Data Editing and Symbologies chapters of the
PRG.
Restore Default
Restore Default
Ì$+$*oÎ
To change the settings refer to the PowerScan™ PD8300 Reference Manual.
Data Format Terminators
For your convenience, some common Terminators are given below. For other
Header/Terminator selections, Data Format and Advanced Data Format parameters, see the PowerScan™ PD8300 Reference Manual.
CR-LF
Ì$+EA120D0A$-ÃÎ
Enter
Ì$+EA1183$-0Î
Tab
Ì$+EA1184$-8Î
None
Ì$+EA10$-dÎ
Operating Test
Read the TEST code below.
Code 128
t
8
e
s
t
PowerScan™ PD8300
Technical Features
Technical Features
PowerScan™ PD8300
Electrical Features
Power Supply
Max. Consumption:
@ 4V
@5V
@30V
Sleep mode
Scan Rat
Reading Indicators
PowerScan™ PD8300
4 to 30 VDC
0.076 mm (3 mils)
420 mA
310 mA
62 mA
4 mA
35 ± 5 scans/sec
Good Read LED (green)
Good Read Spot (green), Beeper
Optical Features
Reading Field
(Typical performance at 20ºC /
68ºF on high quality barcodes)
Max. Resolution
PCS
97.8 cm (38.5 in)
@ 40 mils
0.076 mm (3 mils)
15%
Laser Features
Power (max)
Scan Angle
Laser Safety Class
0.9 mW
42°
Class 2 EN 60825-1/CDRH
Environmental Features
Working Temperature
Storage Temperature
Humidity
Drop Resistance
Protection Class
-30 °C to + 50 °C / -22° to +122 °F
-30 °C to + 70 °C / -22° to +158 °F
90% non condensing
IEC 68-2-32 Test ED 2 m
IP65
Mechanical Features
Weight (without cable)
Cable Length
Quick Reference Guide
about 295 g (10.4 oz)
2 m (6 ft 6 in)
9
Default Values
Default Values
USB-KBD DEFAULT SETTINGS
USA keyboard, FIFO enabled, inter-character and inter-code delays disabled, USB
keyboard speed normal.
DATA FORMAT: code identifier disabled, no field adjustment, code length not
transmitted, no header, terminator = ENTER, character replacement disabled.
RS-232 Standard DEFAULT SETTINGS
9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, delay disabled, rx
timeout 5 sec., ack/nack disabled, FIFO enabled, inter-character delay disabled,
serial trigger lock disabled.
DATA FORMAT: code identifier disabled, no field adjustment, code length not
transmitted, no header, terminator = CR-LF, character replacement disabled.
WEDGE DEFAULT SETTINGS
USA keyboard, caps lock off, caps lock auto-recognition enabled, num lock
unchanged, inter-character and inter-code delays disabled, control character
emulation = ctrl+shift+key.
DATA FORMAT: code identifier disabled, no field adjustment, code length not
transmitted, no header, terminator = ENTER, character replacement disabled.
PEN DEFAULT SETTINGS
interpret operating mode, conversion to code 39 disabled, output level normal,
idle level normal, minimum output pulse 600 μs, overflow medium, inter-block
delay disabled.
CODE SELECTION
·
·
·
·
10
Enabled codes
EAN 8/EAN 13 / UPC A/UPC E without ADD ON
check digit transmitted, no conversions
Interleaved 2/5
check digit control and transmission, variable length code; 4-99 characters
Standard Code 39
no check digit control, variable length code; 1-99 characters
Code 128
variable length code; 1-99 characters
Disabled codes
EAN 128, ISBT128, Code 93, Codabar, pharmaceutical codes, MSI, Code 11,
Code 16K, Code 49, GS1 DataBar™ Codes
PowerScan™ PD8300
Compliance
Compliance
Laser Safety Compliance
The laser scanner conforms to the applicable requirements of both CDRH 21 CFR
1040 and EN60825-1 at the date of manufacture.
The laser light is visible to the human eye and is emitted from the output window (1).
Laser warning and classification label (2).
WARNING
Use of controls or adjustments or performance of procedures other
than those specified herein may result in exposure to hazardous
visible laser light.
The laser scanner utilizes a low-power laser diode. Although staring directly at the
laser beam momentarily causes no known biological damage, avoid staring at the
beam as one would with any very strong light source, such as the sun. Avoid that
the laser beam hits the eye of an observer, even through reflective surfaces such as
mirrors, etc.
The following information is shown on the laser scanner device class label:
ITALIANO
FRANÇAIS
DEUTSCH
ESPAÑOL
Quick Reference Guide
LUCE LASER
NON FISSARE IL RAGGIO
APPARECCHIO LASER DI CLASSE 2
RAYON LASER
EVITER DE REGARDER LE RAYON
APPAREIL LASER DE CLASSE 2
LASERSTRAHLUNG
NICHT IN DEN STRAHL BLICKEN
PRODUKT DER LASERKLASSE 2
RAYO LÁSER
NO MIRAR FIJO EL RAYO
APARATO LÁSERDE CLASE 2
11
Compliance
LED CLASS
Class 1 LED product.
CE Compliance
WARNING
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to
take adequate measures.
FCC Compliance
Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use the equipment.
This device complies with PART 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference which may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Power Supply
This device is intended to be connected to a UL Listed/CSA Certified computer which supplies power directly to the reader or else be supplied by a UL Listed/CSA Certified Power Unit
marked “Class 2” or LPS power source rated 4 - 30 V, minimum 420 mA, which supplies power
directly to the reader via the power connector of the cable.
Características de la
fuente de alimentación
eléctrica.
Atencíon
Entrada:
100 - 240 VCA
min 400 mA 50-60 Hz
Salida:
12VDC, máx 1500mA (-)Negativo al centro
Utilice en su red solo fuentes certificadas en Argentina.
El uso de fuentes de alimentación no compatibles puede resultar en riesgo de
incendio o de choque eléctrico para el usuario.
12
PowerScan™ PD8300
Quick Reference Guide
X
X
X
‫ܝ‬ᄺ㒘ӊ
‫ܝ‬ᄺ㒘ӊ
Assy, Optics Block
Assy, Module
O
O
O
ᳮ
Mercury
(Hg)
叏
O
O
O
Hexavalent
Chromium
(Cr(VI))
Polybrominated
biphenyls
(PBB)
O
O
O
౐ચ卲
O
O
O
ᄙᄽ侶૖
᦭Ქ᦭ኂ‛凝ᚗర⚛
Cadmium
(Cd)
O
O
O
ᄙᄽԲ૖ㅘ
Polybrominated
diphenyl ethers
(PBDE)
Oઍ⴫ᱝẊㇱઙ⊛ᚲ᦭ဋ凝‫ޗ‬றխࢬܶऱ具Ẋ‫ڶ੅ڶ‬୭ढ凝݁‫܅‬Պխ䦀Գ‫ا‬٥ࡉ㧺ॾஒ䣈䢓ຝᚲ咒ؒ⊛
‫ޝ‬䶣՗ॾஒ䣈঴խ‫ڶ੅ڶ‬୭ढ凝ऱૻၦ૞‫ޣ‬ρ(SJ/T 11363-2006) 億ࡳऱૻၦ‫ޕ‬
X:ઍ⴫ᱝẊㇱઙᚲ↪⊛ဋ凝‫ޗ‬றխ, ⥋ዋ᦭৻㮕᧚ᢱ౔ᚲ฽⊛᦭Ქ᦭ኂ‛凝೏Պխ䦀Գ‫ا‬٥ࡉ㧺ॾஒ䣈䢓ຝᚲ咒ؒ⊛
‫ޝ‬䶣՗ॾஒ䣈঴խ‫ڶ੅ڶ‬୭ढ凝ऱૻၦ૞‫ޣ‬ρ(SJ/T 11363-2006) 億ࡳऱૻ㊂
卋
ㇱઙฬ⒓
⬉䏃ᵓ㒘ӊ
Printed Circuit Board Assembly
PART
Lead
(Pb)
Compliance
China RoHS Table of Restricted Elements
13
Compliance
WEEE Compliance
Waste Electrical and Electronic Equipment (WEEE) Statement
English
For information about the disposal of Waste Electrical and Electronic Equipment
(WEEE), please refer to the website at www.datalogic.com.
Italian
Per informazioni sullo smaltimento delle apparecchiature elettriche ed
elettroniche consultare il sito Web www.datalogic.com.
French
Pour toute information relative à l’élimination des déchets électroniques (WEEE),
veuillez consulter le site Internet www.datalogic.com.
German
Informationen zur Entsorgung von Elektro- und Elektronik- Altgeräten (WEEE)
erhalten Sie auf der Webseite www.datalogic.com.
Spanish
Si desea información acerca de los procedimientos para el desecho de los residuos
del equipo eléctrico y electrónico (WEEE), visite la página Web
www.datalogic.com.
Portuguese
Para informações sobre a disposição de Sucatagem de Equipamentos Eléctricos e
Eletrônicos (WEEE - Waste Electrical and Electronic Equipment), consultar o site
web www.datalogic.com.
Chinese
有关处理废弃电气电子设备 (WEEE) 的信息, 请参考 Datalogic 公司的网站:
http://www.datalogic.com/。
Japanese
廃電気電子機器 (WEEE) の処理についての関連事項は Datalogic のサイト
www.datalogic.com, をご参照下さい。
14
PowerScan™ PD8300
Compliance
Datalogic ADC Limited Factory Warranty
Warranty Coverage
Datalogic warrants to Customer that Datalogic's products will be free from defects in materials
and workmanship for a period of one (1) year from product shipment. Datalogic ADC (“Datalogic”) hardware products are warranted against defects in material and workmanship under normal and proper use. The liability of Datalogic under this warranty is limited to furnishing the
labor and parts necessary to remedy any defect covered by this warranty and restore the product to its normal operating condition. Repair or replacement of product during the warranty
does not extend the original warranty term. Products are sold on the basis of specifications applicable at the time of manufacture and Datalogic has no obligation to modify or update products once sold.
If Datalogic determines that a product has defects in material or workmanship, Datalogic shall,
at its sole option repair or replace the product without additional charge for parts and labor, or
credit or refund the defective products duly returned to Datalogic. To perform repairs, Datalogic
may use new or reconditioned parts, components, subassemblies or products that have been
tested as meeting applicable specifications for equivalent new material and products. Customer
will allow Datalogic to scrap all parts removed from the repaired product. The warranty period
shall extend from the date of shipment from Datalogic for the duration published by Datalogic
for the product at the time of purchase (Warranty period). Datalogic warrants repaired hardware
devices against defects in workmanship and materials on the repaired assembly for a 90 day period starting from the date of shipment of the repaired product from Datalogic or until the expiration of the original warranty period, whichever is longer. Datalogic does not guarantee, and it
is not responsible for, the maintenance of, damage to, or loss of configurations, data, and applications on the repaired units and at its sole discretion can return the units in the “factory default”
configuration or with any software or firmware update available at the time of the repair (other
than the firmware or software installed during the manufacture of the product). Customer accepts responsibility to maintain a back up copy of its software and data.
Warranty Claims Process
In order to obtain service under the Factory Warranty, Customer must notify Datalogic of the
claimed defect before the expiration of the applicable Warranty period and obtain from Datalogic a return authorization number (RMA) for return of the product to a designated Datalogic
service center. If Datalogic determines Customer’s claim is valid, Datalogic will repair or replace
product without additional charge for parts and labor. Customer shall be responsible for packaging and shipping the product to the designated Datalogic service center, with shipping
charges prepaid. Datalogic shall pay for the return of the product to Customer if the shipment is
to a location within the country in which the Datalogic service center is located. Customer shall
be responsible for paying all shipping charges, duties, taxes, and any other charges for products
returned to any other locations. Failure to follow the applicable RMA policy, may result in a processing fee. Customer shall be responsible for return shipment expenses for products which Datalogic, at its sole discretion, determines are not defective or eligible for warranty repair.
Warranty Exclusions
The Datalogic Factory Warranty shall not apply to:
(i)
(ii)
(iii)
(iv)
(v)
any product which has been damaged, modified, altered, repaired or upgraded by
other than Datalogic service personnel or its authorized representatives;
any claimed defect, failure or damage which Datalogic determines was caused by
faulty operations, improper use, abuse, misuse, wear and tear, negligence, improper
storage or use of parts or accessories not approved or supplied by Datalogic;
any claimed defect or damage caused by the use of product with any other instrument,
equipment or apparatus;
any claimed defect or damage caused by the failure to provide proper maintenance,
including but not limited to cleaning the upper window in accordance with product
manual;
any defect or damage caused by natural or man-made disaster such as but not limited
to fire, water damage, floods, other natural disasters, vandalism or abusive events that
would cause internal and external component damage or destruction of the whole
unit, consumable items;
Quick Reference Guide
15
Ergonomic Recommendations
(vi)
any damage or malfunctioning caused by non-restoring action as for example firmware or software upgrades, software or hardware reconfigurations etc.;
(vii) the replacement of upper window/cartridge due to scratching, stains or other degradation and/or
(viii) any consumable or equivalent (e.g., cables, power supply, batteries, keypads, touch
screen, triggers etc.).
No Assignment
Customer may not assign or otherwise transfer its rights or obligations under this warranty except to a purchaser or transferee of product. No attempted assignment or transfer in violation of
this provision shall be valid or binding upon Datalogic.
DATALOGIC'S LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
ORAL OR WRITTEN, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT. DATALOGIC SHALL NOT BE LIABLE FOR ANY DAMAGES SUSTAINED BY CUSTOMER
ARISING FROM DELAYS IN THE REPLACEMENT OR REPAIR OF PRODUCTS UNDER THE ABOVE. THE
REMEDY SET FORTH IN THIS WARRANTY STATEMENT IS THE CUSTOMER’S SOLE AND EXCLUSIVE
REMEDY FOR WARRANTY CLAIMS. UNDER NO CIRCUMSTANCES WILL DATALOGIC BE LIABLE TO
CUSTOMER OR ANY THIRD PARTY FOR ANY LOST PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CONTINGENT DAMAGES REGARDLESS OF WHETHER DATALOGIC
HAD ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
Risk of Loss
Customer shall bear risk of loss or damage for product in transit to Datalogic. Datalogic shall assume risk of loss or damage for product in Datalogic’s possession. In the absence of specific written instructions for the return of product to Customer, Datalogic will select the carrier, but
Datalogic shall not thereby assume any liability in connection with the return shipment.
Ergonomic Recommendations
In order to avoid or minimize the potential risk of ergonomic injury follow the
recommendations below. Consult with your local Health & Safety Manager to
CAUTION ensure that you are adhering to your company’s safety programs to prevent
employee injury.
•
•
•
•
•
•
•
•
•
•
•
16
Reduce or eliminate repetitive motion
Maintain a natural position
Reduce or eliminate excessive force
Keep objects that are used frequently within easy reach
Perform tasks at correct heights
Reduce or eliminate vibration
Reduce or eliminate direct pressure
Provide adjustable workstations
Provide adequate clearance
Provide a suitable working environment
Improve work procedures.
PowerScan™ PD8300
Services and Support
Services and Support
Datalogic provides several services as well as technical support through its website.
Log on to www.datalogic.com and click on the links indicated for further information.
Products
Search through the links to arrive at your product page where you can download
specific Manuals and Software & Utilities, including:
•
Datalogic Aladdin™, a multi-platform utility program that allows device
configuration using a PC. It provides RS-232 interface configuration as
well as configuration bar code printing.
Service & Support
•
Technical Support - Product documentation and programming guides and
•
•
Service Programs - Warranty Extensions and Maintenance Agreements
Repair Services - Flat Rate Repairs and Return Material Authorization
•
(RMA) Repairs
Downloads – Manuals & Documentation, Data Sheets, Product Catalogs,
etc.
Technical Support Department in the world
Contact Us
•
Information Request Form and Sales & Service Network.
Quick Reference Guide
17
Services and Support
NOTES
18
PowerScan™ PD8300
DECLARATION OF CONFORMITY
13
Datalogic ADC Srl, Via S. Vitalino, 13
Lippo di Calderara di Reno (BO) 40012 Italy
EC-050
Rev.: 4
Pag.: 1 di 1
La presente dichiarazione di conformità è rilasciata sotto la responsabilità esclusiva di Datalogic ADC Srl
per:
This Declaration of Conformity is issued under the sole responsibility of Datalogic ADC Srl for:
Cette déclaration de conformité est établie sous la seule responsabilité de Datalogic Srl pour:
Diese Konformitätserklärung wird unter der alleinigen Verantwortung des Datalogic ADC Srl erteilt für:
Esta declaración de conformidad se expide bajo la exclusiva responsabilidad de Datalogic ADC Srl para:
PowerScan D83xx ; Barcode Reader
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
den nachstehenden angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
2004/108/EC - EMC Directive
2011/65/EU - RoHS Directive
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla
sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and
product safety.
Basée sur la législation des Etates membres relative à la compatibilté électromagnétique et à la sécurité
des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit
und Produktsicherheit entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad
electromagnética y las Medidas de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
EN 55022 (CLASS A ITE ),
SEPTEMBER 2006:
AMENDMENT A1: OCTOBER 2007:
LIMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE
EN 61000-6-2, AUGUST 2005:
ELECTROMAGNETIC COMPATIBILITY (EMC)
PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL
ENVIRONMENTS
EN 50581, SEPTEMBER 2012 :
TECHNICAL DOCUMENTATION FOR THE ASSESSMENT OF ELECTRICAL AND
ELECTRONIC PRODUCTS WITH RESPECT TO THE RESTRICTION OF HAZARDOUS SUBSTANCES
Lippo di Calderara, March 29th , 2013
CHARACTERISTICS OF INFORMATION TECHNOLOGY EQUIPMENT
RUGGERO CACIOPPO
QUALITY & RELIABILITY MANAGER - EUROPE
www.datalogic.com
©2007-2014 Datalogic, Inc. • All rights reserved.
Datalogic and the Datalogic logo are registered trademarks
of Datalogic S.p.A. in many countries, including the U.S.A.
and the E.U.
Datalogic ADC, Inc.
959 Terry Street | Eugene |OR 97402 | USA
Telephone: (1) 541-683-5700 | Fax: (1) 541-345-7140
820060214
(Rev J)
May 2014
Download PDF