Craftsman | 320.23465 | Operator`s manual | Craftsman 320.23465 Operator`s manual

Operator's
Manual
I CRAFTSMRN°I
2.0 Amp Variable Speed
Multi-Tool
Model No. 320. 23465
c_ius
_l_ WARNING:
To reduce the risk
of injury, the user must read and
understand the Operator's Manual
before using this product.
Sears Brands Management
www.craftsman.com
Corporation
Hoffman
•
•
•
•
•
•
•
•
WARRANTY
SAFETY
UNPACKING
DESCRIPTION
OPERATION
MAINTENANCE
TROUBLESHOOTING
ESPANOL
Estates,
IL 60179
U.S.A.
i_
=[e_[_e_'_
Warranty
Page 2
Safety Symbols
Page 3-4
Safety Instructions
Page 5-9
Unpacking
Page 9-10
Description
Page 10-11
Operation
Page 12-13
Accessory
Tools
Page 14-26
Maintenance
Page 27-28
Troubleshooting
Page 28
Exploded
View and Parts List
Page 29-31
Cratsman
Repair Parts Phone Number
Back Cover
CRAFTSMAN
ONE YEAR LIMITED WARRANTY
FOR ONE YEAR from the date of purchase, this product is warranted
against any defects in material or workmanship. With proof of purchase,
defective product will be replaced free of charge.
For warranty coverage details to obtain free replacement,
web site: www.craftsman.com
This warranty does not cover expendable
blades, sandpaper or rasps.
visit the
parts such as accessory
This warranty is void if this product is ever used while providing
commercial services or if rented to another person.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
Sears Brands Management
Corporation,
Hoffman Estates, IL 60179
A
AlL WARNING: Some dust created by using power tools contains chemicals
known to the state of California to cause cancer and birth defects or other
reproductive harm.
SAVE THESE
INSTRUCTIONS!
READ ALL INSTRUCTIONS!
This Multi-Tool has many features for making its use more pleasant and enjoyable. Safety, performance,
and dependability
have been given top priority in
the design of this product making it easy to maintain and operate.
23465
ManuaLRevised_10
0705
Page 2
The purpose
of safety symbols
is to attract your attention
to possible
dangers.
The safety symbols and the explanations with them deserve your careful
attention and understanding.
The symbol warnings do not, by themselves,
eliminate any danger. The instructions and warnings they give are no substitutes
for proper accident prevention measures.
A_, WARNING:
Be sure to read and understand
all safety instructions
in this
manual, including all safety alert symbols, such as "DANGER," "WARNING," and
"CAUTION,"
before using this Multi-Tool. Failure to follow all instructions listed in
this manual may result in electric shock, fire and/or serious personal injury.
SYMBOL MEANNING
_,
SAFETY
ALERT SYMBOL:
May be used in conjunction
_,
DANGER:
Indicates
DANGER,
with other symbols
WARNING,
Failure to obey this safety warning will result in death or serious
injury to yourself or to others. Always follow the safety precautions
risk of fire, electric shock, and personal injury.
_,
WARNING:
to reduce the
Failure to obey this safety warning can result in death or serious
injury to yourself or to others. Always follow the safety precautions
risk of fire, electric shock, and personal injury.
_lk CAUTION:
OR CAUTION.
or pictographs.
to reduce the
Failure to obey this safety warning may result in death or serious
injury to yourself or to others. Always follow the safety precautions
risk of fire, electric, shock and personal injury.
_, WARNING: To ensure safety and reliability,
at a Sears Parts & Repair Service Center.
all repairs should
to reduce the
be performed
DAMAGE PREVENTION AND INFORMATION MESSAGES
These inform the user of important information and/or instructions that could
lead to equipment or other property damage if they are not followed. Each
message is preceded by the word "NOTE" as in the example below.
NOTE: Equipment
are not followed.
and/or
property
damage
may result if these instructions
The operation of any power tool can result in foreign
objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool
operation, always wear safety goggles or safety glasses
with side shields and a full-face shield when needed.
WEARYOUR
We recommend a Wide Vision Safety Mask for use over
eyeglasses or standard safety glasses with side shields,
available at Sears Stores. Always use eye protection that
is marked to comply with ANSI Z87.1.
23465
ManuaLRevised_10
0705
Page 3
Some of these following symbols may be used on this tool. Please study them
and learn their meaning. Proper interpretation
of these symbols will allow you to
operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency
W
Watt
Power
rain
Minutes
Alternating
---==
Direct
nO
Class
.../rain
Current
Current
Rotational
Per Minute
Read The Operator's
Double-insulated
at no load
construction
Alert
Manual
locations.
Do not expose
speed,
to rain or use in damp
read and understand
operator's
manual
To reduce the risk of injury, user must
before using this product.
glasses with side shields and a full face
Always wear safety goggles or safety
shield when operating this product.
Precautions
No Hands
Symbol
blade
in serious
Failure will
to result
keep your
hands personal
away frominjury.
the
No Hands
Symbol
blade
in serious
Failure will
to result
keep your
hands personal
away frominjury.
the
No Hands
Symbol
blade
in serious
Failure will
to result
keep your
hands personal
away frominjury.
the
No Hands
Symbol
blade
in serious
Failure will
to result
keep your
hands personal
away frominjury.
the
0705
that involve
your safety,
Alert
Hot Surface
23465 ManuaLRevised_lO
speed,
of current
Revolutions,
strokes, surface
orbits, etc., per minute
Eye Protection
Safety
Type of current
Type or a characteristic
II Construction
Wet Conditions
per second)
Time
No Load Speed
]
(cycles
To reduce
avoid
contact
the with
risk of
anyinjury
hot surface.
or damage,
Page 4
_,
WARNING:
Be sure to read and understand
all instructions
before using the Multi-Tool. Failure to follow all instructions
shock, fire and/or serious personal injury.
in this manual
may result in electric
A_, WARNING: Do not attempt to operate this tool until you have thoroughly
read all instructions, safety rules, and warnings. Failure to comply with them can
result in fire, electric shock, or serious personal injury. Save the manual and refer
to it frequently.
GENERAL POWER TOOL SAFETY WARNINGS
_, WARNING: Read all safety warnings and instructions. Failure to follow
the warnings and instructions
may result in electric shock, fire and/or serious
personal injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of warnings refers to your mains-operated
power tool or battery-operated
(cordless) power tool.
(corded)
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions.
power tool will increase the risk of electric shock.
Water entering
a
Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
23465
ManuaLRevised_lO
0705
Page 5
When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
NOTE: The term "residual current device (RCD)" maybe replaced by the
term "ground fault circuit interrupter (GFCI)" or "earth leakage circuit breaker
(ELCB)".
PERSONAL SAFETY
Stay alert, watch what you are doing, and use common sense when
operating a power tool. Do not use the tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattentionwhile
operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection.
Protective equipment, such as dust mask, non-skid safety shoes, hard hat,
or hearing protection, used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure that the switch is in the OFF
position before connecting to power source and/or battery, picking up,
or carrying the tool. Carrying power tools with your finger on the switch or
energizing in power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times.
enables better control of the power tool in unexpected situations.
This
Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and
collection facilities, ensure that these are connected and properly used.
Use of these devices can reduce dust-related hazards.
POWER TOOL USE AND CARE
•
23465
Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and more safely at
the rate for which it was designed..
ManuaLRevised_lO
0705
Page 6
•
Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
Disconnect the plug from the power source and/or the battery from the
power tool before making any adjustments,
changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
•
Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment
or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
•
Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
•
Use the power tool, accessories, tool bits, etc., in accordance
with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
_,
WARNING:
be followed
_,
When using power tools, basic safety precautions
to reduce the risk of fire, electric
WARNING:
The operation
shock, and personal
should always
injury.
of any tool can result in foreign objects
being
propelled into your eyes, resulting in severe eye damage. When operating power
tool, always wear safety goggles or safety glasses with side shields and a full
face shield when needed.
,_
WARNING:
If any parts are missing, do not operate the tool until the missing
parts have been replaced.
Doing so could result in serious
personal
injury.
SERVICE SAFETY
•
Have your power tool
identical replacement
tool is maintained.
serviced by a qualified repair person using only
parts. This will ensure that the safety of the power
If any part of this Multi-Tool is missing or should break, bend, or fail in any
way; or should any electrical component fail to perform properly: shut off the
power switch and remove the Multi-Tool plug from the power source and have
the missing, damaged, or failed parts replaced before resuming operation.
Tool service must be performed only at a Sears Parts & Repair Service
Center. Service or maintenance performed by unqualified personnel could
result in a risk of injury.
23465
ManuaLRevised_lO
0705
Page 7
Use only identical replacement parts when servicing a tool. Follow
the instructions in the Maintenance section of this manual. Use of
unauthorized parts or failure to follow maintenance instructions may create a
risk of electric shock or injury.
SPECIFIC SAFETY RULES FOR MULTI-TOOL
•
Never use your Multi-Tool
conditions.
to perform
sanding or separating
•
Always wear eye protection.
•
Always wear ear protection
•
Always wear a dust mask if the operation
•
Wear protective gloves when changing application
accessories become hot after prolonged usage.
•
Always
•
Always check walls and ceilings to avoid hidden power cables and pipes. A
metal detector (available separately) is very helpful for this purpose.
•
Whenever possible, use clamping
the workpiece to a firm surface.
•
When working with the machine, always hold it firmly with both hands and
provide for a secure stance. The power tool is guided more securely with
both hands.
during extended
operations
in wet
periods of operation.
is dusty.
inspect for and remove all nails, screws,
accessories.
staples, etc. before sanding.
devices or other suitable
Keep your workplace clean. Blends of materials
Dust from light alloys can burn or explode.
Application
means to secure
are particularly
dangerous.
Avoid unintentionally switching on the tool. Ensure that the on/off switch is in
the OFF position before connecting the tool to the power source.
Do not scrape wet or dampened materials (e.g. wallpaper) or on moist
surfaces. Penetration of water into the machine increases the risk of an
electric shock.
Do not treat the surface to be worked with solvent-containing
fluids.
Materials being heated by the scraping can cause toxic vapors to develop.
Exercise extreme caution when handling the scraper accessory.
accessory is very sharp; danger of injury.
The
Use only the original Craftsman accessories and the other accessories
(Fein _ Multi-Master
accessories) available for this Multi-Tool, no others.
_Multi-Master
is registered trademarks of FEIN Power Tools Inc.
Only use application
are torn or worn.
23465
ManuaLRevised_lO
0705
accessories
in good condition.
FEIN
Do not use them if they
Page 8
Do not restart a cutting operation in the workpiece. To resume a cutting
operation: while keeping the tool from contacting the workpiece, allow the
tool reach full speed and then carefully guide the cutting accessory into the
cut.
•
Keep your hands away from the cutting
being cut.
•
Hold power tools by their insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal parts of the tool "live" and
shock the operator.
1,WARNING:
loss.
Wear ear protection.
area. Do not reach under the material
Exposure
to noise can cause hearing
_, WARNING: To avoid injury, hold the tool by the insulated gripping surfaces
only. If the tool contacts hidden wiring or its own cord, exposed metal parts
of the tool could shock the operator and cause serious injury. Make sure that
hidden electrical wiring, water pipes, or other hazards are not in the cutting path.
_,
WARNING: Your Multi-Tool
should never be connected to the power
source when you are assembling parts, making adjustments, installing
or removing blades, cleaning, or when it is not in use. Disconnecting the
Multi-Tool will prevent accidental starting, which could cause serious
personal injury.
When unpacking the box, do not discard any packing materials until all of
the contents are accounted for:
1.
Carefully
surface.
2.
Open the color box to locate the following:
23465
lift the Multi-Tool
•
Multi-Tool
•
Circular Saw Blade
•
Flush Cut Blade
•
Carbide Triangular
•
Carbide Circular
•
Scraper Blade
•
Sanding Base Plate
•
9 pieces Sandpaper
•
Hex Key
ManuaLRevised_10
0705
out of the carton and place on a stable, flat
rasp
Blade
(3pieces each of 60, 120, 180 grit )
Page 9
3.
•
Vacuum Adapter
•
Manual
Inspect the items carefully to make sure that no breakage or damage has
occurred during shipping. If any of the items mentioned is missing, (refer to
"PARTS LIST" illustration), return the Multi-Tool to your nearest Sears store
to have the Multi-Tool replaced.
A_, WARNING: If any part is broken or missing, do not attempt to assemble
the Multi-Tool, plug in the power cord, or operate the Multi-Tool until the
broken or missing part is replaced. Failure to do so could result in possible
serious injury.
CARTON CONTENTS/LOOSE
23465
ManuaLRevised_lO
0705
PARTS (Fig. 1)
Page 10
ID]_.'_o_[[e_]
KNOW YOUR MULTI-TOOL (Fig. 2)
Fig. 2
Live tool indicator"
On/Off switch
LED light
cord
LED worklight
Vacuum
adapter
Vents
Drive shaft
;}iiii[ii!iiiii[_
Flange bolt
Variable speed dial
Before attempting to use this Multi-Tool, familiarize
operating features and safety requirements.
This Multi-Tool
has the following
yourself with all of its
features:
•
A multifunction
drive shaft system that allows the tool to be used for dry
sanding of small surfaces, corners and edges, for scraping, for sawing thin
steel sheet, wood and plastic by attaching different application tools supplied.
•
2.0 Amps,
•
Variable speed
•
LED worklight
•
"Live tool indicator" LED light shines green when the Multi-Tool
into a power source.
•
The vacuum adapter can improve dust extraction, when it is installed on the tool
and connected with a dust-extraction system or a suitable vacuum cleaner.
11000 to 19000 oscillation
is controlled
illuminates
working
PRODUCT
Input
per minute variable speed motor.
by the seed dail located
on the back of the tool.
area.
SPECIFICATIONS
2.0Amps
Oscillation
Rate
11000 to 19000/Min
Oscillation
Angle
_+1.4 degrees
Rating
120 volts, 60Hz AC
Weight
2.71 Ibs (1.23 kg)
23465
is plugged
ManuaLRevised_10
0705
Page 11
ON/OFF SWITCH (Fig. 3)
1.
Connect the power cord of
your Multi-Tool to a standard
household power outlet.
2.
To turn the tool ON, push
the on/off switch forward.
3.
To turn the tool OFF, push
the switch backward.
Fig. 3
VARIABLE SPEED DIAL (Fig. 4)
The variable speed feature of
this Multi-Tool allows you to
match the proper speed to
the material being cut, sawed,
scraped or sanded, enhancing
the overall performance of
your tool and helping to save
the application accessory from
undue wear.
1.
Fig. 4
The variable speed dial is
used to adjust the speed of the application
accessory.
2.
Turn the dial to increase or decrease
3.
Position "1" selects the slowest speed and position "6" selects the fastest
speed. Adjust the application accessory speed for optimum performance.
NOTE: Determine
of material.
the optimum
the speed of the tool. (Fig.4).
speed for by making a trial cut in a scrap piece
LED WORKLIGHT (Fig. 5)
The LED worklight, located
on the front of the tool, will
illuminate when the ON/
OFF switch is in the forward
(ON) position. This provides
additional light on the surface
of the workpiece for operation
in lower-light conditions.
The LED worklight will turn
off when the switch is slid
backwards
23465
Fig. 5
LED worklight
(OFF).
ManuaLRevised_10
0705
Page 12
LIVE TOOL INDICATOR LED LIGHT (Fig. 6)
Your Multi-Tool
has a "live
tool indicator" green LED
light, located on the back of
the tool. This light turns on
automatically
when the MultiTool is plugged into a power
source.
23465
ManuaLRevised_lO
0705
Fig. 6
Live Tool Indictor
LED light
Page 13
SELECTING
THE APPLICATION
ACCESSORY
_h, WARNING: If any part is broken or missing, do not attempt to plug in the
power cord or operate the tool until the broken or missing part is replaced.
Failure to do so could result in possible serious injury.
ACCESSORY
MATERIALS
Carbide Circular Blade
Grout, Plaster, Porous Concrete
and Masonry
Hardened
Carbide Triangular
adhesives,
Rasp
Thinset, Wood, Masonry
Scraper Blade
Paint & Varnish, Bonded Carpet,
Soft Adhesives, Vinyl Flooring,
wood and other floor coverings.
Circular Saw Blade
Wood, Plastic, Drywall, NonFerrous Metals, thin Sheet Metal
and other materials
Flush Cut Blade
Wood, Plastic, Drywall, Soft
Metals and other Materials
Sanding
Plate and
Bare or painted wood, plaster,
and other surfaces, depending
on sandpaper grit ............................................
Sandpaper
ATTACHING
_,
WARNING:
THE ACCESSORY
TOOL
Failure to disconnect
the tool from power source when
assembling parts, making adjustments, or changing
accidental starting causing possibly serious injury.
accessories
could result in
A_, CAUTION: For all work or when changing accessory tools, always wear
protective gloves. The sharp edges of the accessory tools will cause personal
injury. Accessory tools can be very hot while working.
_,
WARNING:
Check that the accessory
or insecurely fastened
cause a hazard.
_,
WARNING:
scraper
position
accessory
tools are correctly
Do not attach the circular
saw blade,
blade, or flush cut blade facing backwards,
may cause serious injury.
23465 ManuaLRevised_lO
0705
attached.
Incorrect
tools can come loose during operation
carbide
circular
as operation
and
blade,
in this
Page 14
NOTE: Replacement Craftsman accessories and additional Craftsman accessories
are available at Sears and Craftsman retailers. Refer to the model numbers for
purchase.
Fig. 7
SANDPAPER KIT (67655)
DESCRIPTION
(Fig. 7)
Q
• 24 pieces sandpaper (8 pieces
each 60, 120 and 180 grit).
•
•
O
0
Always apply to the
compatible sanding plate
(supplied with your Multi-Tool).
0
O
Sandpaper kit is also
compatible
with the Fein ®
Multi-Master tool.
MOUNTING/CHANGING
_,
WARNING:
sanding
THE SANDPAPER
(Fig. 8)
Check that the
plate and sandpaper
Fig. 8
are correctly attached. An
incorrect or insecurely fastened
application tool can come
loose during operation and
cause a hazard.
1.
Follow the directions
!
for
Attaching the Application
Tool to attach the sanding
plate to the Multi-Tool.
2.
Align the sandpaper with
the sanding plate and use
your hand to press it firmly
onto the sanding plate.
3.
Press the sandpaper firmly against a smooth surface for a short period, then
switch on the tool. The burr will form a non-slip bond with the outer edge of
the sandpaper felt. This will avoid premature wear.
4.
If one point has become worn, pull off the sandpaper,
it on the sanding plate again.
23465
ManuaLRevised_10
0705
turn it 120 ° and place
Page 15
SANDING
_,
(Fig. 9)
WARNING:
Do not touch
the gear box after prolonged
use; it could be very hot.
•
The removal rate and the
sanding pattern are determined
by the choice of sanding sheet
and the work surface.
Apply uniform sanding
pressure to extend the life of
the sanding sheets.
Intensifying the sanding
pressure does not lead to
an increase of the sanding
capacity, but instead it increases
wear on the machine and the sanding sheet.
Use only the tip or an edge of the sanding sheet for precise sanding
corners and hard to reach areas.
of edges,
When selectively sanding on one spot, the sanding sheet can heat up
considerably.
Remove the tool from the surface periodically to permit the
sanding sheet to cool down.
A sanding
materials.
sheet that has been used for metal should not be used for other
Use only original
For sanding,
Craftsman
sanding
always connect
accessories.
dust extraction.
1.
For Rough sanding use 40-80 grit paper.
2.
For Smooth
3.
For Fine sanding
sanding
use 100-180 grit paper.
use 220-320
girt paper.
SAWING WITH THE CIRCULAR SAW BLADE (67651)
DESCRIPTION (Fig. 10)
•
High speed steel circular
cutting blade.
Fig. 10
Designed for cutting wood,
plastic, drywall, nonferrous
metals, thin sheet metal and
other materials.
•
The circular saw blade is also
compatible
with the Fein ®
Multi-Master tool.
23465
ManuaLRevised_10
0705
Page 16
TO INSTALL
_,
THE CIRCULAR
CAUTION:
SAW BLADE
Wear protective
gloves.
_, WARNING:
Use sharp, undamaged
blades or saw blades that are otherwise
saw blades only. Deformed,
damaged can break.
_1, WARNING:
When sawing light building materials,
and the recommendations
of the material suppliers.
WARNING:
wood, gypsum
Plunge cuts may only be applied
plaster boards, etc.
_I, WARNING:
and application.
The sawing
Disconnect
the precautions
to soft materials,
such as
teeth are very sharp. Do not touch during mounting
_, WARNING:
Do not attach
the circular saw blade facing
backwards (Fig. 11), which may
hurt the user.
1.
observe
blunt saw
Fig. 11
the Multi-Tool
from the power source.
2.
Loosen the flange bolt with
the hex key provided.
(Fig. 12)
3.
Ensure that the inner
threads and the drive shaft
are clean.
4.
Align the grooves on the
circular saw blade with the
four raised ribs on the drive
Fig. 12
shaft; put the blade on the
drive shaft. (Fig. 13)
5.
23465
With your gloved hand
holding the blade, put on
and tighten the flange bolt
using the hex key.
ManuaLRevised_10
0705
Fig. 13
Page 17
NOTE: The ribs on the
shaft and the grooves in the
accessory tools permit a firm
connection of the accessory
tools in increments of 30 °
Fig. 14
around the shaft (Fig. 14).
Apply the accessory tool in the
orientation appropriate to the
task at hand.
CUTTING WITH THE
CIRCULAR SAW BLADE
(Fig. 15)
1.
Connect
the Multi-Tool
r---
to a
power source.
2.
Securely clamp the
workpiece if necessary.
3.
Draw the cutting
the workpiece.
4.
Apply the blade to the
workpiece.
5.
Switch on the tool and
apply appropriate pressure
to make the cut.
23465
Manual_Revised_lO-0705
lines on
Page 18
CARBIDE CIRCULAR BLADE
(67650)
Fig. 16
DESCRIPTION (Fig. 16)
The Carbide Circular
Blade is
designed to cut out the grout
around wall tiles. It can also
be used to cut plaster, porous
concrete and masonry.
•
Carbide-tipped,
grout disc.
•
Designed for grout, plaster,
masonry or porous concrete
removal around the wall tiles.
•
The carbide circular
TO INSTALL
circular
blade is also compatible
THE CARBIDE
A_, CAUTION:
CIRCULAR
Wear protective
_lk WARNING: Do not attach
the carbide circular blade facing
backwards (Fig. 17), which
hurt the user.
1.
Disconnect
with the Fein ® Multi-Master.
BLADE
gloves.
Fig. 17
may
the Multi-Tool
from the power source.
2.
3.
23465
Loosen the flange bolt with
the hex key provided.
(Fig. 18)
Fig. 18
Ensure that the inner
threads and the drive shaft
are clean.
ManuaLRevised_lO
0705
Page 19
4.
Align the grooves on the
carbide circular blade with
the four raised ribs on the
Fig. 19
drive shaft; put the carbide
circular blade onto the drive
shaft. (Fig. 19)
5.
With your gloved hand
holding the carbide circular
blade, put on and tighten
the flange bolt using the hex
key.
NOTE: The ribs on the
shaft and the grooves in the
accessory tools permit a firm
connection of the accessory
tools in increments of 30 °
Fig. 20
around the shaft (Fig. 20).
Apply the accessory tool in the
orientation appropriate to the
task at hand.
//_
w_/
23465
ManuaLRevised_lO
0705
Page 20
CUTTING WITH THE CARBIDE CIRCULAR BLADE (Fig. 21)
Connect the Multi-Tool to a
power source.
1.
2.
3.
Draw the cutting
the workpiece.
lines on
Place the carbide
circular
Fig. 21
blade against the workpiece
at a 90 ° angle.
Switch on the tool, cut out
the grout around the wall
tile, then use a hand chisel
to remove the tile.
4.
NOTE: When separating wall
tiles, take into consideration
that the accessory tools wear
heavily when used for longer
periods of time.
SCRAPER BLADE (67652)
DESCRIPTION (Fig. 22)
Steel scraping blade
designed for paint &
varnish, bonded carpet, soft
adhesives, vinyl flooring,
wood and other floor
coverings.
•
Scraper blade is also
compatible
with the Fein ®
Multi-Master tool.
TO INSTALL
BLADE
THE SCRAPER
,_
CAUTION:
Wear protective
gloves.
_,
CAUTION:
For all work or when changing
accessory
protective gloves. The sharp edges of the accessory
injury. Accessory tool can be very hot while working.
A_, WARNING:
Do not attach
the scraper blade facing
backwards (Fig. 13), which
hurt the user.
23465
ManuaLRevised_10
0705
tool, always wear
tool will cause personal
Fig. 23
may
Page 21
_,
WARNING:
Check that
Fig. 24
the accessory tool is correctly
attached. Incorrect or
insecurely fastened accessory
tool can come loose during
operation and cause a hazard.
1.
Disconnect
the Multi-Tool
from the power source.
2.
3.
4.
Loosen the flange bolt with
the hex key provided.
(Fig. 24)
Ensure that the inner
threads and the drive shaft
are clean.
Fig. 25
Align the grooves on the
scraper blade with the four
raised ribs on the drive
shaft; put the blade onto the
drive shaft. (Fig. 25)
5.
With your gloved hand
holding the blade, put on
and tighten the flange bolt
using the hex key.
NOTE: The ribs on the
shaft and the grooves in the
accessory tools permit a firm
connection of the accessory
tools in increments of 30 °
Fig. 26
around the shaft (Fig. 26).
Apply the accessory tool in the
orientation appropriate to the
task at hand.
23465
ManuaLRevised_10
0705
Page 22
USING THE SCRAPER BLADE (Fig. 27)
Connect the Multi-Tool to a
power source.
1.
Fig. 27
2.
To scrape, put the tool on
the workpiece at a flat angle
(not more than 20°), and
apply only light pressure
so as to not cut into the
surface.
3.
To cut and remove carpet,
place the Scraper Blade
vertically on the workpiece,
switch the tool on, and
cut the carpet. Then place
the scraper blade between the carpet and the floor to the coverings
adhesive residue off.
CARBIDE
TRIANGULAR
DESCRIPTION
and
RASP (67654)
(Fig. 28)
Fig. 28
•
Carbide tipped
grout rasp.
triangular
•
Designed for grout, masonry,
thinset, wood and removal of
hardened adhesives on the
wall tiles.
•
Triangular rasp is also
compatible
with the Fein ®
Multi-Master tool.
TO INSTALL THE CARBIDE
TRIANGULAR
RASP
CAUTION:
Wear protective
Fig. 29
gloves.
1.
Disconnect
the Multi-Tool
from the power source.
2.
Loosen the flange bolt with
the hex key provided.
(Fig. 29)
3.
Ensure that the inner
threads and the drive shaft
are clean.
23465
ManuaLRevised_10
0705
Page 23
4.
Align the grooves on the
carbide triangular rasp with
the four raised ribs on the
Fig. 30
drive shaft; put the disc
onto the drive shaft.
(Fig. 30)
5.
With your gloved hand
holding the carbide
triangular rasp put on and
tighten the flange bolt using
the hex key.
NOTE: The ribs on the
shaft and the grooves in the
accessory tools permit a firm
connection of the accessory
tools in increments of 30 °
Fig. 31
around the shaft (Fig. 31).
Apply the accessory tool in the
orientation appropriate to the
task at hand.
USING THE CARBIDE
TRIANGLUAR RASP (Fig. 32)
1.
Connect
the Multi-Tool
to a
power source.
2.
Put the rasp flat against
the workpiece and apply
appropriate pressure.
3.
Switch on the tool, remove
any hardened adhesive or
grout on the surface of the
wall tiles.
23465
ManuaLRevised_lO
0705
Fig. 32
Page 24
FLUSH CUT BLADE (67653)
Fig. 33
DESCRIPTION (Fig. 33)
• Bi-metal, straight-edge,
flush-cut blade.
•
Designed for cutting wood,
plastic, drywall, soft metal
and other materials.
•
Can plunge and saw with a slight pendulum
•
Flush Cut blade is also compatible
TO INSTALL
_,
action in wood.
with the Fein ® Multi-Master
tool.
THE FLUSH CUT BLADE
CAUTION:
Wear protective
WARNING:
Do not attach
gloves.
A
the flush-cut blade facing
backwards (Fig. 34), which
may hurt the user.
1.
Disconnect
I
I Fig. 34
the Multi-Tool
from the power source.
2.
3.
23465
Loosen the flange bolt with
the hex key provided.
(Fig. 35)
Fig. 35
Ensure that the inner
threads and the drive shaft
are clean.
ManuaLRevised_10
0705
Page 25
4.
Align the grooves on the
flush-cut blade with the
four raised ribs on the drive
Fig. 36
shaft; put the blade onto the
drive shaft. (Fig. 36)
5.
With your gloved hand
holding the blade, put on
and tighten the flange bolt
using the hex key.
NOTE: The ribs on the
shaft and the grooves in the
accessory tools permit a firm
connection of the accessory
tools in increments of 30 °
Figl 37
....",
around the shaft (Fig. 37).
Apply the accessory tool in the
orientation appropriate to the
task at hand.
USING THE FLUSH CUT
BLADE (Fig. 38)
1.
7
Connect the Multi-Tool to a
power source.
2.
Clamp the workpiece
securely.
3.
Draw the cutting
the workpiece.
4.
Put the blade along the line.
5.
Switch on the tool, and
apply with appropriate
pressure until the blade
cuts to the depth needed
according to the scale on
the blade.
lines on
Fig. 38
Multi-Tool Accessories Available Separately
Craftsman Sandpaper kit (17374)
Craftsman Detail Cutting Blade (17375)
Craftsman Rough Cut Blade (17376)
Check at sears.com or your Craftsman retailer for additional
23465
ManuaLRevised_lO
0705
accessories.
Page 26
Craftsman
Craftsman
Craftsman
Craftsman
Craftsman
Craftsman
Carbide circular blade (67650)
Circular saw blade (67651)
Scraper blade (67652)
Flush cut blade (67653)
Carbide triangular rasp (67654)
24pc. Sandpaper kit (67655)
GENERAL
MAINTENANCE
_1, WARNING:
When servicing,
use only identical
Craftsman
replacement
parts.
Use of any other parts may create a hazard or cause product damage. To ensure
safety and reliability, all repairs should be performed by a qualified service
technician at a Craftsman Parts & Repair Service Center
WARNING:
Multi-Tool
cleaning.
For your safety, always turn off the switch and unplug the
motor from the power source before performing
any maintenance
or
_, WARNING: Avoid using solvents when cleaning plastic parts. Most plastics
are susceptible to damage from various types of commercial solvents and may
be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
MULTI-TOOL MAINTENANCE
Periodic maintenance
operation.
A cleaning
of your Multi-Tool
and maintenance
schedule
As a common-sense
and preventive
recommended
steps:
the accessory
allows for long life and trouble-free
should
be maintained.
maintenance
practice,
follow
these
•
Inspect
•
Keep the ventilation
motor.
•
Use a soft clean and damp cloth to wipe the tool housing. A mild detergent
can be used but nothing like alcohol, petrol or other cleaning agent. Never
use caustic agents to clean plastic parts.
A_, WARNING:
tool; check the rim for wear or damage.
slots of the motor clean to prevent
When changing
allow the accessory
an accessory
overheating
tool immediately
tool to cool before removing
of the
after operation,
it to avoid possible
burning.
WARNING:
Keep the tool's air vents unclogged
and clean at all times.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-based
products, penetrating oils, etc. to come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may result in serious personal injury.
_,
23465
WARNING:
ManuaLRevised_10
Water must never come into the tool.
0705
Page 27
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient amount of highgrade lubricant for the life of the tool under normal operating conditions.
Therefore, no further lubrication is required.
b/_l[l_
[,,1][[I][I]llll]_]
PROBLEM
CAUSE
SOLUTION
Motor overheating
Be sure cooling vents
are free from dust and
obstacles,
Clean, clear vents. Do not
cover with hand during
operation.
23465
ManuaLRevised_lO
0705
Page 28
o_
.-0
4--,
"0
__..
c"0
_1
c'-" 0
_
.I..o
_
r-
_
=
°2o
.__ _
.I..o
2.0A Variable Speed Multi-Tool MODEL NUMBER 320.23465
The Model Number will be found on the Nameplate attached to the handle of
the Multi-Tool. Always mention the Model Number when ordering parts for this
tool.
1
3121045000
Cord Guard
1
2
3120234000
Cord Anchorage
1
3
4890690000
PCB Assembly
1
4
3125549000
Right Cover
1
5
4540017000
Power Supply
6
3125548000
Left Cover
1
7
4930008000
Sleeve
4
8
4930038000
Receptacle
4
201
2823032000
Motor ASSY
1
9
2730165000
DC Motor
1
10
5620038000
Screw
2
11
3125477000
Fan
1
12
3402451000
Connector
1
13
3125478000
Switch
1
14
3321074000
Left Housing
1
15
3121003000
Rubber
2
16
3125531000
LED Cover
1
202
2823033000
Shaft ASSY
1
17
3551619000
Eccentric
Shaft
1
18
5660020000
Circlips
For Hole
1
19
5700048000
Ball Bearing
1
20
3551459000
Bearing
1
21
5690180000
O ring
1
22
5650216000
Plain Washer
1
23
3704682000
Counterweight
1
23465
ManuaLRevised_10
0705
Indicator
Actuator
Insert
Support
1
Page 30
24
3700352000
Washer
1
25
5700205000
Ball Bearing
1
26
5660144000
Circlips
1
27
3125185000
Dust Cover
203
2823034000
Drive Housing
28
5700022000
Needle Bearing
1
29
3421144000
Drive Housing
1
30
5700053000
Needle Bearing
1
31
3421179000
Lever
1
32
5700048000
Ball Bearing
1
33
5660020000
Circlips
1
34
3551577000
Spindle
1
35
5690018000
O Ring
1
36
5650300000
Washer
1
37
5620445000
Screw
1
38
3810456000
Rasper
1
39
3810454000
Blade
1
40
3810453000
Scraper
1
41
3810504000
BIM Plunge
42
3810452000
Grinding
Wheel
1
43
3320814000
Base Plate Set
1
44
2820442000
Sanding
1
45
3124550000
Vacuum Adapter
46
5610024000
Tapping
47
3321075000
Right Housing
1
48
4810002000
Power Cord & Plug
1
49
5680169000
Inner Hexagon
1
23465
ManuaLRevised_lO
0705
For Shaft
1
ASSY
For Hole
Cut Saw Blade
Paper
1
1
1
11
Screw
Spanner
Page 31
Your Home
For troubleshooting, product manuals and expert advice:
managemylife
www.managemylife.com
For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
Ca, anytirne, day or night
(1-800-469-4663)
www.sears.com
(U.S.A. and Canada)
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of the nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
www.sears
1-800-469-4663 (Canada)
.com
www
.sears
.ca
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
Para pedir serviciode reparaci6n
a domicilio,y para ordenar piezas:
1-888-SU-HOGAR®
1-800-361-6665 (Canada)
Au Canada pour serviceen frangais:
1-800-LE-FOYERMc
(1-800-533-6937)
(1-888-784-6427)
www.sears.com
ealrS
® Registered
® Marca
Mc Marque
Trademark
/ TMTrademark
of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries
/ TN Marca de F&brica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC in otros paises
Registrada
de commerce
/ MDMarque
d_pos_e
de Sears
Brands,
LLC
Download PDF