ALLIANCE | Home Laundry Automatic Washer | Service manual | ALLIANCE Home Laundry Automatic Washer Service manual

Troubleshooting
Home Automatic
Washers
Refer to Page 6 for Model Numbers
W001C
www.comlaundry.com
Part No. 201143R4
June 2009
Table of
Contents
Section 1 – Safety Information .........................3
Locating an Authorized Servicer ............................ 5
Section 2 – Introduction ....................................6
Model Identification ............................................... 6
How Your Washer Works .................................... 10
Customer Service ................................................. 12
Nameplate Location ............................................. 12
Section 3 – Troubleshooting............................13
1. No Hot Water ................................................... 14
2. No Cold Water .................................................. 15
3. No Warm Water ............................................... 16
4. Water Fill Does Not Stop At Proper Level ...... 17
5. Timer Does Not Advance ................................. 18
6. Motor Does Not Run ........................................ 19
7. No Agitation ..................................................... 20
8. Constant Agitation ............................................ 21
9. Washer Overheats, Cycles On Motor
Thermal Protector, Switch Actuator
Kicks In and Out ................................................... 22
10. Slow Spin ....................................................... 23
11. No Spin ........................................................... 24
12. Constant Spin ................................................. 25
13. Washer Stops In Cycle; Quits After a
Couple Loads; Is Intermittent ............................... 26
14. Washer Is Locked Up Or Binding .................. 27
15. Outer Tub Does Not Empty ............................ 28
16. Excessive Vibration ........................................ 29
17. Water Leaking From Outer Tub ..................... 30
Section 4 – Adjustments ..................................31
18. Leveling Legs ................................................. 31
19. Pressure Switch .............................................. 32
20. Belt (Agitate and Spin) ................................... 32
Section 5 – Test Procedures ............................33
21. Motor Test Procedure ..................................... 33
22. Mixing Valve Solenoid Test Procedure ......... 34
23. Temperature Switch Test Procedure .............. 34
© Copyright 2009, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Section 6 – Cycle Sequence Charts.................35
Timer No. 37004 Cycle Sequence........................ 36
Timer No. 37922 Cycle Sequence........................ 38
Timer No. 37925 Cycle Sequence........................ 40
Timer No. 37927 Cycle Sequence........................ 41
Timer No. 37928, 37929, 37930 and
200885 Cycle Sequence ....................................... 42
Timer No. 37995 Cycle Sequence........................ 43
Timer No. 38881 Cycle Sequence........................ 44
Timer No. 39445 and 201013
Cycle Sequence ..................................................... 46
Timer No. 200604 Cycle Sequence...................... 47
Timer No. 200927 Cycle Sequence...................... 48
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Section 1
Safety Information
Throughout this manual and on machine decals, you will find precautionary statements (“CAUTION,”
“WARNING,” and “DANGER”) followed by specific instructions. These precautions are intended for the personal
safety of the operator, user, servicer and those maintaining the machine.
a DANGER
Danger indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death.
a WARNING
Warning indicates a hazardous situation that, if not avoided, could cause severe personal injury or death.
a CAUTION
Caution indicates a hazardous situation that, if not avoided, may cause minor or moderate personal injury or property
damage.
Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.
IMPORTANT
The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will
occur if the procedure is not followed.
NOTE
The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is
important but not hazard related.
In the interest of safety, some general precautions relating to the operation of this machine follow.
WARNING
• Failure to install, maintain and/or operate this product according to the manufacturer’s
instructions may result in conditions which can produce serious injury, death and/or
property damage.
• Do not repair or replace any part of the product or attempt any servicing unless specifically
recommended or published in this Service Manual and unless you understand and have the
skills to carry out the servicing.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the product is properly grounded and to reduce the risk of fire,
electric shock, serious injury or death.
W006R2
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Safety Information
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
WARNING
Repairs that are made to your products by unqualified persons can result in hazards due to
improper assembly or adjustments subjecting you, or the inexperienced person making such
repairs, to the risk of serious injury, electrical shock, or death.
W007
WARNING
If you or an unqualified person perform service on your product, you must assume the
responsibility for any personal injury or property damage which may result. The manufacturer
will not be responsible for any injury or property damage arising from improper service and/or
service procedures.
W008
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Safety Information
NOTE: The WARNINGS and IMPORTANT
INSTRUCTIONS appearing in this manual are not
meant to cover all possible conditions and situations
that may occur. Common sense, caution and care
must be exercised when installing, maintaining or
operating the washer.
Locating an Authorized Servicer
Always contact your dealer, distributor, service agent
or the manufacturer about any problems or conditions
you do not understand.
Warranty service must be performed by an authorized
technician, using authorized factory parts. If service is
required after the warranty expires, Alliance Laundry
Systems also recommends contacting an authorized
technician and using authorized factory parts.
201143
Alliance Laundry Systems is not responsible for
personal injury or property damage resulting from
improper service. Review all service information
before beginning repairs.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Section 2
Introduction
Model Identification
Information in this manual is applicable to these washer models.
Model
Number
1 Speed
Motor
AWN552SN301AW01
AWZ17N*-1102
2 Speed
Motor
3 Speed
Motor
Porcelain Washtub
(cu. ft.)
X
Stainless Steel
Washtub (cu. ft.)
3.3
X
3.3
AWZ45N*-1102
X
3.3
AWZ52N*-1102
X
3.3
AWZ53N*-1102
X
3.3
CWN311SP111CW01
X
3.3
CWN412SP111CW01
X
3.3
LWB19A*-1109
X
3.3
LWB19B*-1109
X
3.3
LWB19M*-1109
X
3.3
LWD51N*-1100
X
3.3
LWD52M*-1100
X
3.3
LWD52N*-1100
X
3.3
LWG74A*-3050
X
3.3
LWH16N*-3322
X
3.3
LWH18A*-3322
X
3.3
LWH18N*-3322
X
3.3
LWK23A*-3050
X
3.3
LWK24A*-3050
X
3.3
LWK24N*-3050
X
3.3
LWK73A*-3050
X
3.3
LWK74A*-3050
X
3.3
LWK74N*-3050
X
3.3
LWS01A*-1000
X
2.9
LWS01A*-1088
X
2.9
LWS01A*-3088
X
2.9
LWS01A*-3300
X
2.9
LWS01M*-1000
X
2.9
LWS01M*-3088
X
2.9
LWS01M*-3300
X
2.9
LWS01N*-3088
X
2.9
LWS01N*-3300
X
2.9
LWS11A*-3062
X
3.3
LWS11N*-3062
X
3.3
LWS16A*K
X
3.3
* Add Letter To Designate Color. L – Almond W – White Q – Bisque
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Introduction
Model
Number
1 Speed
Motor
2 Speed
Motor
3 Speed
Motor
Porcelain Washtub
(cu. ft.)
LWS16A*-1000
X
3.3
LWS16A*-3000
X
3.3
LWS16A*-3022
X
3.3
LWS16A*-3300
X
3.3
LWS16A*-3322
LWS16B*K
LWS16M*K
LWS16M*-1000
LWS16M*-3000
LWS16M*-3022
LWS16M*-3300
LWS16M*-3322
LWS16N*-1000
LWS16N*-3022
LWS16N*-3322
LWS16N*K
LWS17A*K
LWS17A*-1000
LWS17A*-3000
LWS17A*-3022
LWS17A*-3028
LWS17A*-3050
LWS17A*-3300
LWS17A*-3322
LWS17A*B3020
LWS17A*B3069
LWS17B*K
LWS17M*K
LWS17M*-1000
LWS17M*-1127
LWS17M*-3000
LWS17M*-3022
LWS17M*-3050
LWS17M*-3300
LWS17M*-3322
LWS17M*B3020
LWS17M*B3069
LWS17N*-1000
LWS17N*-1127
LWS17N*-3000
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
Stainless Steel
Washtub (cu. ft.)
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
* Add Letter To Designate Color. L – Almond W – White Q – Bisque
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Introduction
Model
Number
LWS17N*-3022
LWS17N*-3028
LWS17N*-3300
LWS17N*-3322
LWS17N*B3020
LWS17N*B3069
LWS17N*K
LWS21A*-3062
LWS21N*-3062
LWS42M*-3050
LWS42N*-3050
LWS45M*-1127
LWS45N*-1127
LWS45N*-1130
LWS52N*-1127
LWT42N*-1100
LWT52N*-1100
LWY17A*-1109
LWY17B*-1109
LWY17M*-1109
LWY45A*-1109
LWY45B*-1109
LWY45M*-1109
LWZ01M*-1102
LWZ01N*-1102
LWZ16A*-1000
LWZ16M*-1000
LWZ16N*-1000
LWZ17A*-3000
LWZ17A*B3020
LWZ17A*B3069
LWZ17M*-3000
LWZ17M*B3020
LWZ17M*B3069
LWZ17N*-3022
LWZ17N*B3020
LWZ17N*B3069
LWZ20M*-3300
LWZ20N*-3300
LWZ22M*-1102
1 Speed
Motor
2 Speed
Motor
3 Speed
Motor
Porcelain Washtub
(cu. ft.)
Stainless Steel
Washtub (cu. ft.)
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
2.9
X
2.9
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
* Add Letter To Designate Color. L – Almond W – White Q – Bisque
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Introduction
Model
Number
LWZ22N*-1102
LWZ42M*-1102
LWZ42N*-1102
LWZ52M*-1102
LWZ52N*-1102
LWZ77M*-1102
LWZ77N*-1102
ZWN311SP111CW01
ZWN412SP111CW01
ZWN432SP111CW01
1 Speed
Motor
2 Speed
Motor
3 Speed
Motor
X
Porcelain Washtub
(cu. ft.)
Stainless Steel
Washtub (cu. ft.)
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
X
3.3
* Add Letter To Designate Color. L – Almond W – White Q – Bisque
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Introduction
How Your Washer Works
Pressure
Switch
Temperature
Switch
Timer
Mixing
Valve
Agitator
Washtub
Outer
Tub
Transmission
Motor
Pump
W407SE3A
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Introduction
The cycle begins with a wash fill. The water
temperature is determined by the temperature selector.
While water fills the washtub, a column of air is
trapped in a pressure bulb and hose. The air pressure
continues to increase as the washtub fills with water
until it is great enough to activate the pressure switch.
The pressure switch then causes the wash fill to stop
and wash agitation to begin. However, the loading door
must be closed for the washer to agitate or spin.
The washer uses a reversing type motor, a special drive
belt and an idler assembly. The idler assembly applies
tension to the outside of the drive belt.
During agitation, the motor runs in the
counterclockwise direction. The spring tension on the
idler pulley applies the tension required to reduce the
slack on the drive belt and maintain maximum belt to
motor pulley contact. This eliminates belt slippage and
ensures an efficient wash action, even with extra large
loads.
The belt drives the transmission drive pulley in the
counterclockwise direction. The pulley drives the helix
which is splined to the input shaft of the transmission.
This causes the input shaft to turn inside of a roller
clutch which is pressed into the transmission cover.
This roller clutch acts as a bearing in the
counterclockwise direction allowing the transmission
gears to operate. The transmission’s rack and pinion
gear design produces a 210 degree agitation stroke at
the output shaft of the transmission which drives the
agitator. The brake assembly remains locked during the
agitation mode since no pressure is applied to it by the
transmission drive pulley.
As water is removed by the pump and the momentum
of the washtub increases, the idler spring tension
gradually overcomes the belt tension removing the belt
slack. This eventually increases the belt to pulley
contact until maximum spin speed is achieved.
The combination of water, washtub and load weight
cause the drive belt tension on the idler side of the belt
to overtake the idler spring pressure allowing the belt to
become slack on the opposite side. This reduces the
belt to pulley contact and allows slipping between the
belt and pulley.
The drive pulley turns clockwise riding up the ramps of
the helix, exerting pressure on the brake and forcing it
to release from brake pads. The helix drives the input
shaft of the transmission, and when the input shaft turns
in the clockwise direction the roller clutch locks onto
the shaft causing the entire transmission assembly to
turn. None of the gears in the transmission are
operating at this time. The hub of the washtub is splined
to the transmission tube and rotates with the
transmission assembly. The centrifugal force created
by the spinning washtub causes water to be extracted
from the clothes.
Water is introduced during the first spin to “SPRAY”
the garments and remove suds from them. The initial
spin is followed by rinse agitation to rinse away any
detergent residue. The washer fills and then agitates
like the wash portion of the cycle. Following rinse
agitation, a final spin extracts the rinse water from the
clothes preparing them for the dryer.
After the wash agitation is completed, the timer
advances into the first spin. During spin, the motor
reverses turning in the clockwise direction to spin the
water out of the washtub.
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Introduction
Customer Service
Nameplate Location
If literature or replacement parts are required, contact
the source from whom the machine was purchased or
contact Alliance Laundry Systems at (920) 748-3950
for the name and address of the nearest authorized parts
distributor.
When calling or writing about your product, be sure to
mention model and serial numbers. Model and serial
numbers are located on nameplate(s) as shown.
1
For technical assistance, call (920) 748-3121.
W429S
1
12
Nameplate
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Section 3
Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
IMPORTANT: Refer to Wiring Diagram for aid in
testing washer components.
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Troubleshooting
1. No Hot Water
There is no hot water.
Is unit plugged in
and power
available to outlet?
No
Check plug
and reset
circuit
breaker.
Yes
Is temperature
switch
inoperative?
No
Is timer
inoperative?
Is the water
supply faucet
closed?
Yes
No
No
Yes
Check water heater.
Yes
Straighten or
replace hose.
No
Yes
Disconnect hot
fill hose and
clean or
replace screen.
Yes
No
Is pressure
hose
clogged?
Is the mixing valve
screen or screen in
outer end of fill hose
nearest water supply
faucet clogged?
Yes
Yes
Test switch.
Must have
continuity from
terminal 1 to 2
when empty or
1-3 when full.
Replace if
inoperative.
Remove and
clean or
replace hose.
No
Is there
broken, loose
or incorrect
wiring?
Yes
No
14
Test
solenoid and
replace if
necessary.
No
Is pressure
switch
inoperative?
No
Is the hot water
fill hose kinked?
Test for
continuity
Yes through timer
circuits (refer to
wiring diagram)
and replace if
inoperative.
Open faucet.
Is hot water
mixing valve
solenoid
inoperative?
Is the water
supply cold?
Yes Test switch
and replace if
inoperative.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Refer to
appropriate
wiring
diagram.
TLW371S
201143
Troubleshooting
2. No Cold Water
There is no cold
water.
Is unit plugged in
and power
available to outlet?
No
Check plug
and reset
circuit
breaker.
Is timer
inoperative?
Yes
No
Test for
continuity
through timer
circuits (refer
to wiring
diagram) and
replace if
inoperative.
Yes
Is the water
supply faucet
closed?
Yes
Open faucet.
Is cold water
mixing valve
solenoid
inoperative?
Yes
Test
solenoid
and
replace if
necessary.
No
No
Is the cold
water fill hose
kinked?
Yes
Straighten or
replace hose.
Is pressure
switch
inoperative?
Yes
No
Test switch.
Must have
continuity from
terminal 1 to 2
when empty or
1-3 when full.
Replace if
inoperative.
No
Is the mixing valve
screen or screen in
outer end of fill hose
nearest water supply
faucet clogged?
Disconnect
Yes cold fill hose
and clean or
replace screen.
Is pressure
hose
clogged?
Yes
Remove and
clean or
replace hose.
No
No
Is temperature
switch
inoperative?
Yes Test switch
and replace if
inoperative.
Is there
broken, loose
or incorrect
wiring?
Yes
Refer to
appropriate
wiring
diagram.
TLW372S
No
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Troubleshooting
3. No Warm Water
There is no warm
water.
Is there no
hot water?
Yes
Refer to No Hot
Water paragraph.
No
Is there no
cold water?
Yes
Refer to No Cold
Water paragraph.
TLW362S
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Troubleshooting
4. Water Fill Does Not Stop At Proper Level
Water fill does not
stop at proper level.
Is pressure
switch
inoperative?
Yes
Test switch and
replace if
inoperative.
No
Is there an
air leak in
pressure
hose?
Yes
Was there a siphoning
action started in washer
causing water to be
siphoned from washer
during cycle due to end
of drain hose being
lower than cabinet top of
washer?
Replace
hose.
Does drain
hose fit tight
in standpipe
or drain?
Is mixing
valve
inoperative?
No
Yes
Test valve and
replace if
inoperative.
Install 562P3
Siphon
Break Kit.
No
No
Yes
Provide an air
gap around drain
hose and drain
Yes receptacle.
Install No. 36878
Standpipe
Adapter (optional
on some
models).
No
Is there
water in
pressure
hose?
Yes
Blow air through
hose to remove
water or replace
hose.
No
Is there
broken,
loose,
shorted or
incorrect
wiring?
Yes
Refer to
appropriate
wiring diagram.
TLW348S
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Troubleshooting
5. Timer Does Not Advance
Timer does not advance.
Yes
Is lid
open?
Close lid. Lid
MUST be closed
any time the
washer is set to
agitate or spin.
Is washer
siphoning
during rinse
fill?
No
No
Is timer
inoperative?
Is circuit breaker
to washer tripped,
disconnecting
power to washer?
Yes
Reset circuit
breaker.
No
Timer is designed
to stop under
these conditions.
Motor thermal
proctor reset time
may vary
depending upon
Yes the reason for
washer overload,
however, it should
reset within 15
minutes. Check to
ensure washer
was not
overloaded with
clothes.
Has washer
drive motor
over loaded
and motor
thermal
overload been
tripped?
No
Is pause part
of normal
operation?
No
Yes
Yes
Timer is designed to
pause during fill
periods and when
going from agitate to
spin. Allow completion
of those steps. Some
cycles (delicate) have
additional pauses.
Refer to diagram for
information on time
required.
Yes
No
Washer
will not fill?
No
Is timer
motor lead
wire off timer
terminal?
Install siphon
break kit, Part
No. 562P3.
Test for
continuity
through timer
circuits (refer to
wiring diagram)
and replace if
inoperative.
Timer pauses until
pressure switch is
satisfied. Timer is
designed to pause
Yes
when going from
spin into rinse to
allow the washtub to
stop spinning before
filling. Make sure
timer has advanced
into fill portion of
rinse cycle.
Refer to
Yes appropriate
wiring diagram
and reattach
wire.
No
Is there
broken, loose
or incorrect
wiring?
Yes
Refer to
appropriate
wiring diagram.
TLW363S
18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Troubleshooting
6. Motor Does Not Run
Motor does not run.
Is electrical
power off, fuse
blown or power
cord not
plugged in?
Check laundry
room for blown or
loose fuse(s) or
Yes open circuit
breakers.
(Washer itself
does not have an
electrical fuse.)
Are motor
starting functions
inoperative; no
start or motor
hums only?
No
Is motor dead,
won't run?
No
Yes
Refer to Test
Procedures
section to
check start
switch and
start windings.
Refer to Test
Procedures
section to
check switch
and windings.
Yes
No
Is lid open or
lid switch
inoperative?
Yes
Close lid or
test switch and
replace if
inoperative.
No
Is power
cord
miswired?
Yes
Refer to
appropriate wiring
diagram for
correct wiring.
Yes
No
Is timer
inoperative?
No
Yes
Reset timer or
try another
cycle.
Test for
continuity
through timer
circuits (refer
to wiring
diagram) and
replace if
inoperative.
Yes
Wait two or three
minutes for overload
protector to reset. If
protector cycles
repeatedly, refer to
Paragraph 9.
No
Is there a bind in
upper or lower
motor bearing?
No
Is timer
improperly
set?
Has motor
overload
protector
cycled?
Yes
Remove belt and
determine if
motor shaft will
spin. Replace
motor if shaft is
locked up.
No
Is there a
bind in
pump?
Yes
Replace pump.
No
Is there
broken,
loose or
incorrect
wiring?
Yes
Refer to
appropriate
wiring diagram.
TLW364S
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Troubleshooting
7. No Agitation
No agitation.
Has drive
motor overload
protector
cycled?
Yes
Wait two or three
minutes for
overload protector
to reset. If
protector cycles
repeatedly, refer
to Paragraph 9.
Is there
broken, loose
or incorrect
wiring?
Yes
Refer to
appropriate
wiring diagram.
No
No
Are pauses
part of
normal cycle?
Yes
Timer is
designed to
pause (SOAK)
during
DELICATE
cycle. Allow
completion of
SOAK period.
Is drive belt
broken or
loose?
Yes
Replace belt.
No
No
Is timer
inoperative?
Yes
No
Motor
won't run?
Yes
Test for
continuity
through timer
circuits (refer to
wiring diagram)
and replace if
inoperative.
Refer to Test
Procedures section
to check switch
and windings.
Is transmission
assembly
inoperative?
Yes
Repair or
replace
transmission
assembly.
No
Remove drive
motor and
Yes replace roll pin
and any other
damaged
parts.
Is motor pulley
roll pin sheared
(through Serial
No. 001113645)?
No
No
No delicate
cycle
agitate?
Yes
Refer to Test
Procedures
section to check
low speed switch
and windings.
Is there a
bind in
pump?
Yes
Replace pump.
No
Is pressure
switch
inoperative?
No
Yes
Test switch. Must
have continuity
from terminal 1 to
3. Replace if
inoperative.
No
Is lid open
or lid switch
inoperative?
Close lid or test
Yes switch and
replace if
inoperative.
TLW358S
20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Troubleshooting
8. Constant Agitation
Constant agitation.
Is timer
inoperative?
Yes
Test for
continuity
through timer
circuits (refer to
wiring diagram)
and replace if
inoperative.
No
Is there
shorted or
incorrect
wiring?
Yes
Refer to appropriate
wiring diagram.
No
Does washer
agitate during
spin cycle?
Yes
Repair or
replace
transmission
assembly.
TLW365S
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Troubleshooting
9. Washer Overheats, Cycles On Motor Thermal Protector, Switch Actuator
Kicks In And Out
Washer overheats, cycles on
motor thermal protector, switch
actuator kicks in and out.
Is belt tacky,
not allowing
proper slip?
Yes
Check belt and
replace if
defective.
Are brake
pads or
brake
assembly
binding?
Yes
Free binding
pads, or replace
pads and brake
assembly.
No
No
Is belt tension
too great, not
allowing
proper slip?
Yes
Make sure idler
spring is
properly
connected.
No
Yes
Is timer
inoperative?
No
Test for
continuity
through timer
circuits (refer to
wiring diagram)
and replace if
inoperative.
Have
bearings,
transmission
or motor
locked up and
will not turn?
No
Is voltage
incorrect?
Are motor
switch
functions
inoperative?
Yes
Refer to Test
Procedures
section to check
switch
functions.
Check that all
these
components are
Yes able to move
freely. Correct
or replace
binding
component.
Yes
No
Check for
foreign objects
between inner
and outer tubs.
No
Is there a bind
in water pump?
Yes
Replace pump.
No
22
Contact local
utility company,
or have a
qualified
electrician check
power supply.
TLW366S
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Troubleshooting
10. Slow Spin
Slow spin.
Is there a
bind in
pump?
Yes
Replace pump.
No
Is
transmission
assembly
inoperative?
Yes
Repair or
replace the
transmission
assembly.
No
Is drive
belt
broken or
loose?
Yes
Replace belt.
Is there oil
on belt?
Yes
Replace belt.
No
Is motor pulley
roll pin sheared
(through Serial
No. 001113645)?
Yes
Remove drive
motor and
replace roll pin
and any other
damaged
parts.
No
Is there no
clearance
between
brake pads
and discs?
Yes
Replace pads
and brake
assembly.
No
TLW359S
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Troubleshooting
11. No Spin
No spin.
Yes
Is timer
inoperative?
No
Is lid open
or lid switch
inoperative?
Yes
Test for
continuity
through timer
circuits (refer
to wiring
diagram) and
replace if
inoperative.
Close lid or test
switch and
replace if
inoperative.
Has drive
motor
overload
protector
cycled?
No
Is there no
clearance
between
brake pads
and discs?
No
Is there a
bind in
pump?
Yes
Wait two or three
minutes for
overload protector
to reset. If
protector cycles
repeatedly, refer
to Paragraph 9.
Yes
Replace pads
and brake
assembly.
Yes
Refer to
appropriate
wiring diagram.
Yes
Replace pump.
No
No
Is drive
belt
broken or
loose?
Is there
broken, loose
or incorrect
wiring?
Yes
Replace belt.
No
No
Yes
Motor
won't run?
Refer to Test
Procedures
section to
check switch
and windings.
Is there oil
on belt?
Yes
Replace belt.
No
Is motor pulley roll
pin sheared
(through Serial No.
001113645)?
Remove drive
motor and
Yes replace roll pin
and any other
damaged
parts.
No
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
TLW367S
201143
Troubleshooting
12. Constant Spin
Constant spin.
Is timer
inoperative?
Yes
Test for
continuity
through timer
circuits (refer to
wiring diagram)
and replace if
inoperative.
No
Is there
excessive wear
on brake pads
or missing
brake pads?
Yes
Replace brake
pads and brake
assembly.
No
Is there
shorted or
incorrect
wiring?
Yes
Refer to appropriate
wiring diagram.
Yes
Replace lid
switch.
No
Is lid switch
inoperative?
TLW368S
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Troubleshooting
13. Washer Stops In Cycle; Quits After A Couple Loads; Is Intermittent
Washer stops in cycle, quits
after a couple loads or is
intermittent.
Is belt tacky,
not allowing
proper slip?
Yes
Check belt and
replace if
defective.
Has motor
overload
protector
cycled?
Yes
No
Wait two or three
minutes for
overload protector
to reset. If
protector cycles
repeatedly, refer
to Paragraph 9.
No
Is belt tension
too great, not
allowing
proper slip?
Yes
Make sure idler
spring is
properly
connected.
Are motor
switch
functions
inoperative?
No
Is timer
inoperative?
Yes
Test for
continuity
through timer
circuits (refer to
wiring diagram)
and replace if
inoperative.
No
Is there
broken, loose
or incorrect
wiring?
Yes
Refer to
appropriate wiring
diagram.
Yes
Refer to Test
Procedures
section to check
switch functions.
No
Has brake,
transmission
or motor
locked up and
will not turn?
Yes
Check that all
these
components
are able to
move freely.
No
TLW356S
26
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Troubleshooting
14. Washer Is Locked Up Or Binding
Washer is locked up or binding.
Is there
excessive
belt tension?
Yes
Replace belt
and/or idler
spring.
No
Is there a bind
in upper or
lower bearing
during spin?
Yes
Replace bearing.
Are brake
pads
binding
during spin
only?
Yes
Free binding
pads or
replace pads.
No
Is there a
bind in water
pump?
Yes
Replace pump.
No
Is there a
bind in
transmission
during
agitation
only?
Yes
Repair or replace
transmission.
No
201143
TLW369S
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Troubleshooting
15. Outer Tub Does Not Empty
Outer tub does
not empty.
Is drain hose
kinked?
Yes
Straighten hose.
No
Is water pump
inoperative?
Yes
Replace pump.
No
Is there an
obstruction
in outer tub
outlet hose?
Yes
Remove obstruction.
TLW370S
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Troubleshooting
16. Excessive Vibration
Excessive vibration.
Is there an
unbalanced
load in tub?
Yes
Stop washer,
redistribute
load, then
restart washer.
No
Is there a
broken or
disconnected
centering
spring(s)?
Yes
Connect or
replace centering
spring(s).
Yes
Yes
Replace base
assembly.
No
Is there
lubricant on
pivot dome
and/or base
friction ring?
No
Is washer
unleveled?
Is base
damaged
(washer was
dropped)?
Yes
Remove
lubricant or
replace
parts.
Adjust leveling
legs.
No
No
Is washer
installed on
weak, "spongy",
carpeted or
built-up floor?
Relocate washer or
Yes support floor to
eliminate weak or
"spongy" condition.
Is partial
liquid filled
balance ring
leaking?
Yes
Replace
balance ring.
No
No
Are cabinet
screws
incorrect or
loose?
Is friction
ring
broken?
Yes
Yes
Replace
friction ring.
Replace with
correct screws
or tighten.
No
TLW357S
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Troubleshooting
17. Water Leaking From Outer Tub
Water leaking from
outer tub.
Is water seal
in outer tub
leaking?
Yes
Replace hub
and seal kit
assembly.
Is there an
obstruction in
drain causing
water to come
over top of outer
tub cover?
No
Is there a
hole in outer
tub?
Yes
Yes
Remove
obstruction.
Replace outer
tub.
No
No
Is pressure
hose or
accumulator
leaking?
Yes
Replace
pressure hose
and/or
accumulator.
Is tub-topump hose
leaking at
clamp?
Yes
Tighten clamp.
No
Is outer tub
cover
gasket
leaking?
Yes
Replace gasket.
No
TLW341S
30
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Section 4
Adjustments
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
18. Leveling Legs
Refer to Figure 1.
a. Place rubber feet on all four leveling legs.
b. Place washer in position on a clean, dry, and
reasonably firm floor.
c. Loosen locknuts and adjust two front leveling
legs. Once adjusted, tilt washer forward on
front legs and lower back down into position
to set the rear self-leveling legs.
d. Washer must not rock. After washer is at
desired height, tighten locknuts securely
against bottom of washer base. If these
locknuts are not tight, washer will not remain
stationary during operation.
NOTE: Improper installation, installation on carpet
or flexing of a weak floor will cause excessive
vibration.
IMPORTANT: Do not slide washer across floor
once leveling legs have been extended, as legs and
base could become damaged.
Level
Washer
Base
Locknut
Rubber
Foot
Leveling
Leg
W456SE3A
Figure 1
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Adjustments
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
19. Pressure Switch
Refer to Figure 2.
NOTE: DO NOT ADJUST PRESSURE SWITCH
IF WASHER IS WITHIN THE WARRANTY
PERIOD.
Adjusting
Screw
Pressure switch is set at the factory for proper water
fill levels. However, if there is a problem of
overfilling or underfilling, pressure switch can be
adjusted.
Maximum water fill level can be increased by
turning adjusting screw CLOCKWISE, and
decreased by turning screw
COUNTERCLOCKWISE.
One quarter turn of the adjusting screw represents
approximately one inch (25.4 mm) increase or
decrease of water level in washtub.
W457SE1B
Figure 2
20. Belt (Agitate And Spin)
No belt adjustment is required.
IMPORTANT: DO NOT turn adjusting screw
more than 3/4 of a turn in either direction as the
switch may be damaged and flooding could result.
When testing, pressure switch has continuity from
terminal 1 to 2 when empty and 1 to 3 when full.
32
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Section 5
Test Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
21. Motor Test Procedure
IMPORTANT: Disconnect base wire harness plug from motor.
WARNING
Disconnect electric power to washer before performing the following steps:
W188
Motor test procedures using an Ohm meter.
NOTE: Resistance readings slightly out of given ranges may be due to meter conditions. These readings DO
NOT necessarily indicate motor failure.
Meter Connections
Reading Should
Be
1.
Ground to Each Other Terminal
Open
2.
White to Yellow
3.
Red to Brown
2-8 Ohms
Start winding open or resistance too high or too low.
Blue to White
1-2 Ohms
High speed winding (4 pole) open or resistance too
high or too low.
2.5 Ohms
(Approximate)
Low winding opening; High speed winding open; or
resistance too high or too low.
4.
5.
Closed
Violet to White (2-speed motor)
If Not
Terminal shorted to ground.
Open thermal overload.
6.
“R” to Red
Closed
Open start (auxiliary) switch.
7.
“P” to Blue (2-speed motor)
Closed
Open start switch 4 pole winding.
NOTE: Steps 8, 9 and 10 are with motor centrifugal mechanism in the run position.
8.
9.
10.
201143
Open
“R” to Red
“P” to Blue (2-speed motor)
3 Ohms
(approximate)
“P” to Blue (2-speed motor)
Closed
Start auxiliary switch.
Refer to Blue to White and Violet to White.
Open low (6 pole) winding run switch.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Test Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
22. Mixing Valve Solenoid Test Procedure
Mixing valve test procedures using an Ohm meter.
NOTE: Resistance readings slightly out of given ranges may be due to meter conditions. These readings DO
NOT necessarily indicate mixing valve failure.
120 Volt coils
240 Volt coils
900 - 1100 Ohms
3200 - 4000 Ohms
23. Temperature Switch Test Procedure
Check for continuity between the following terminal connections:
3 Position Switches
Temperature
Connection
Wash
Rinse
Hot
Cold
L-3
Warm
Cold
L - 3- 4
Cold
Cold
L-4
4 Position Switches
Temperature
Wash
Rinse
Hot
Cold
Warm
Warm
Warm
Cold
Cold
Cold
Connection
L1 - 2
L1 - 1, L1 - 2, L2 - 2, L2 - 1, L2 - L1, 1 - 2
L1 - 2, L1 - 1, 1 - 2
L1 - 1
5 Position Switches
Temperature
Wash
Rinse
Hot
Cold
Hot
Warm
Warm
Cold
Warm
Warm
Cold
Cold
34
Connection
L1 - 2
L1 - 2, L2 - 2
L1 - 1, L1 - 2
L1 - 1, L1 - 2, L2 - 2
L1 - 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Section 6
Cycle Sequence Charts
CYCLE SEQUENCE CHARTS
FOUND ON THE FOLLOWING PAGES
ARE FOR TIMERS COVERED IN THIS MANUAL.
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
PERMANENT PRESS
WASH FILL & AGITATE
WATER
TEMP.
SELECT
*MOTOR
SPEED
H,W,C
FAST
PAUSE
TIME (Min.
& Sec.)
9:47
2:17
DRAIN
:30
FILL & PAUSE
C
2:27
DRAIN
2:00
DRAIN & SPIN
RINSE FILL & AGITATE
W,C
SLOW
2:11
FAST
4:00
PAUSE (:40) & DRAIN
3:00
INTERVAL DRAIN & SPIN
SLOW
DRAIN/SPIN/SPRAY
C
DRAIN & SPIN
1:51
SLOW
:47
SLOW
4:31
OFF
2:30
WASH FILL & AGITATE
H,W,C
SLOW
H,W,C
SLOW
DELICATE & WOOLENS
PAUSE
1:56
2:05
AGITATE
PAUSE
:47
1:43
AGITATE
H,W,C
SLOW
PAUSE
:35
2:07
DRAIN
:30
FILL & PAUSE
W,C
2:27
DRAIN
2:00
DRAIN & SPIN
SLOW
2:11
SLOW
1:40
PAUSE
:40
RINSE FILL & AGITATE
W,C
PAUSE (:40) & DRAIN
3:00
INTERVAL DRAIN & SPIN
SLOW
DRAIN/SPIN/SPRAY
W,C
DRAIN & SPIN
1:51
SLOW
:47
SLOW
4:31
2:30
SOAK/PREWASH
OFF
OFF
WASH FILL & AGITATE
H,W,C
FAST
PAUSE
AGITATE
H,W,C
FAST
1:49
H,W,C
FAST
1:49
PAUSE
5:41
AGITATE
INFINITE PAUSE UNLESS L-T CONNECTED EXTERNALLY
2:30
DRAIN
2:20
INTERVAL DRAIN & SPIN
FAST
UNLESS L-T CONNECTED EXTERNALLY
1:51
2:30
WASH FILL & AGITATE
REGULAR
2:26
5:13
H,W,C
FAST
14:55
PAUSE (:40) & DRAIN
2:40
DRAIN & SPIN
2:11
PAUSE
:40
RINSE FILL & AGITATE
W,C
FAST
PAUSE (:40) & DRAIN
4:07
3:00
INTERVAL DRAIN & SPIN
FAST
DRAIN/SPIN/SPRAY
COLD
DRAIN & SPIN
1:51
FAST
:47
FAST
4:31
(continued)
TIMER NO. 37004 CYCLE SEQUENCE
36
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Cycle Sequence Charts
UNLESS L-T CONNECTED EXTERNALLY
EXTRA
RINSE
OFF
2:30
W,C
RINSE FILL & AGITATE
FAST
PAUSE (:40) & DRAIN
4:27
3:00
INTERVAL DRAIN & SPIN
DRAIN & SPIN
OFF
FAST
FAST
1:51
2:30
2:30
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37004 CYCLE SEQUENCE
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Cycle Sequence Charts
WATER
TEMP.
SELECT
*MOTOR
SPEED
SOAK
SOAK FILL & AGITATE
H,W,C
SELECT
SOAK FILL
H,W,C
PREWASH
NOTE: Times listed are approximate.
WASH FILL & AGITATE
CYCLE
FUNCTION
SPIN
TIME (Min.
& Sec.)
3:00
12:00
SELECT
3:00
SELECT
6:00
SELECT
3:00
SELECT
15:00
SELECT
3:00
SELECT
:25
SELECT
2:35
OFF
3:00
H,W,C
SPIN
REGULAR
WASH FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
EXTRA
RINSE
OFF/PAUSE
SELECT
3:00
SELECT
6:00
CYCLE END OR PAUSE FOR EXTRA RINSE
3:00
RINSE FILL & AGITATE
W,C
SPIN
SELECT
3:00
SELECT
6:00
OFF
PERMANENT
PRESS
OFF
EXTRA
RINSE
OFF/PAUSE
WASH FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
SELECT
9:00
MEDIUM
3:00
MEDIUM
:25
MEDIUM
2:35
SELECT
3:00
SELECT
6:00
CYCLE END OR PAUSE FOR EXTRA RINSE
3:00
RINSE FILL & AGITATE
W,C
SPIN
SELECT
3:00
SELECT
6:00
3:00
DELICATE
OFF
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
C
SPIN
OFF/PAUSE
CYCLE END OR PAUSE FOR EXTRA RINSE
3:00
MEDIUM
:25
2:35
MEDIUM
:25
2:35
MEDIUM
3:00
MEDIUM
:25
MEDIUM
2:40
MEDIUM
3:00
MEDIUM
3:00
3:00
(continued)
TIMER NO. 37922 CYCLE SEQUENCE
38
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
EXTRA
RINSE
Cycle Sequence Charts
RINSE FILL & AGITATE
C
SPIN
MEDIUM
3:00
MEDIUM
3:00
OFF
3:00
HANDWASH
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
C
SPIN
3:00
SLOW
SLOW
:25
MEDIUM
3:00
2:35
MEDIUM
:25
MEDIUM
2:40
SLOW
3:00
MEDIUM
OFF
:25
2:35
3:00
3:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37922 CYCLE SEQUENCE
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39
Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
WASH FILL & AGITATE
WATER
TEMP.
SELECT
H,W,C
REGULAR
SPIN
*MOTOR
SPEED
FAST
FAST
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
SPIN & SPRAY
C
SPIN
TIME (Min.
& Sec.)
15:00
1:30
FAST
:25
FAST
2:35
FAST
3:00
FAST
1:30
FAST
:25
FAST
7:05
OFF
3:00
PERMANENT
PRESS
WASH FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
SPIN & SPRAY
C
SPIN
FAST
9:00
SLOW
1:30
SLOW
:25
SLOW
2:35
FAST
3:00
FAST
1:30
FAST
:25
FAST
7:05
OFF
3:00
DELICATE
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
C
SPIN
SPIN & SPRAY
C
SPIN
OFF
1:30
SLOW
:25
2:35
SLOW
:25
2:35
SLOW
:25
SLOW
1:30
1:05
SLOW
:25
SLOW
2:35
SLOW
3:00
SLOW
1:30
SLOW
:25
SLOW
4:05
3:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37925 CYCLE SEQUENCE
40
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Cycle Sequence Charts
NOTE: Times listed are approximate.
WATER
TEMP.
SELECT
*MOTOR
SPEED
SOAK FILL & AGITATE
H,W,C
SLOW
SOAK FILL
H,W,C
SOAK
CYCLE
FUNCTION
SPIN
TIME (Min.
& Sec.)
4:00
12:00
SLOW
4:00
FAST
15:30
FAST
2:00
FAST
:30
FAST
1:30
OFF
4:00
REGULAR
WASH FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
FAST
4:00
FAST
6:00
FAST
9:30
SLOW
2:00
4:00
PERMANENT
PRESS
OFF
WASH FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
SLOW
:30
SLOW
1:30
FAST
4:00
FAST
6:00
4:00
DELICATE
OFF
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
3:00
SLOW
1:30
SLOW
C
SPIN
RINSE FILL & AGITATE
C
SPIN
OFF
:30
1:30
SLOW
:30
1:30
SLOW
:30
1:30
SLOW
SPIN & SPRAY
:30
2:00
SLOW
:30
SLOW
1:30
SLOW
4:00
SLOW
4:00
4:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37927 CYCLE SEQUENCE
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
REGULAR
WASH FILL & AGITATE
WATER
TEMP.
SELECT
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
*MOTOR
SPEED
TIME (Min.
& Sec.)
FAST
15:00
FAST
1:30
FAST
:25
FAST
2:35
FAST
3:00
FAST
6:00
FAST
9:00
SLOW
1:30
3:00
PERMANENT
PRESS
OFF
WASH FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
SLOW
:25
SLOW
2:35
FAST
3:00
FAST
6:00
OFF
3:00
DELICATE
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
C
SPIN
1:30
SLOW
:25
2:35
SLOW
:25
2:35
SLOW
:25
SLOW
1:30
1:05
SLOW
:25
SLOW
2:35
SLOW
3:00
SLOW
3:00
OFF
3:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37928, 37929, 37930 AND 200885 CYCLE SEQUENCE
42
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
WASH FILL & AGITATE
WATER
TEMP.
SELECT
*MOTOR
SPEED
H,W,C
FAST
PERMANENT
PRESS
PAUSE (:23) & DRAIN
TIME (Min.
& Sec.)
9:35
1:13
FILL AND PAUSE
C
2:25
DRAIN
2:00
DRAIN & SPIN
SLOW
RINSE FILL & AGITATE
W,C
FAST
PAUSE (:23) & DRAIN
2:23
4:23
2:23
INTERVAL DRAIN & SPIN
FAST
DRAIN/SPIN/SPRAY
C
DRAIN & SPIN
1:34
FAST
:52
FAST
4:45
OFF
3:36
REGULAR
WASH FILL & AGITATE
H,W,C
FAST
14:23
PAUSE (:23) & DRAIN
2:23
DRAIN & SPIN
2:23
PAUSE
:23
RINSE FILL & AGITATE
W,C
FAST
PAUSE (:23) & DRAIN
4:23
2:23
INTERVAL DRAIN & SPIN
DRAIN/SPIN/SPRAY
C
DRAIN & SPIN
OFF
FAST
1:34
FAST
:52
FAST
4:45
3:36
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 37995 CYCLE SEQUENCE
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
43
Cycle Sequence Charts
WATER
TEMP.
SELECT
*MOTOR
SPEED
SOAK
SOAK FILL & AGITATE
H,W,C
SLOW
SOAK FILL
H,W,C
PREWASH
NOTE: Times listed are approximate.
WASH FILL & AGITATE
CYCLE
FUNCTION
SPIN
TIME (Min.
& Sec.)
3:00
12:00
SLOW
3:00
FAST
6:00
FAST
3:00
FAST
15:30
FAST
3:00
FAST
:25
FAST
2:35
OFF
3:00
H,W,C
SPIN
REGULAR
WASH FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
EXTRA
RINSE
OFF/PAUSE
FAST
3:00
FAST
6:00
CYCLE END OR PAUSE FOR EXTRA RINSE
3:00
RINSE FILL & AGITATE
W,C
SPIN
FAST
3:00
FAST
6:00
OFF
PERMANENT
PRESS
OFF
EXTRA
RINSE
OFF/PAUSE
WASH FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
FAST
9:30
SLOW
3:00
SLOW
:25
SLOW
2:35
FAST
3:00
FAST
6:00
CYCLE END OR PAUSE FOR EXTRA RINSE
3:00
RINSE FILL & AGITATE
W,C
SPIN
FAST
3:00
FAST
6:00
3:00
DELICATE
OFF
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
C
SPIN
3:00
SLOW
:25
2:35
SLOW
:25
2:35
SLOW
3:00
SLOW
:25
SLOW
2:35
SLOW
3:00
SLOW
3:00
(continued)
TIMER NO. 38881 CYCLE SEQUENCE
44
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Cycle Sequence Charts
EXTRA
RINSE
OFF/PAUSE
CYCLE END OR PAUSE FOR EXTRA RINSE
RINSE FILL & AGITATE
3:00
C
SPIN
OFF
SLOW
3:00
SLOW
3:00
3:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 38881 CYCLE SEQUENCE
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
45
Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
PERMANENT PRESS
WASH FILL & AGITATE
WATER
TEMP.
SELECT
*MOTOR
SPEED
H,W,C
FAST
PAUSE
TIME (Min.
& Sec.)
9:41
2:23
DRAIN
:30
FILL & PAUSE
C
2:06
DRAIN
2:00
DRAIN & SPIN
RINSE FILL & AGITATE
W,C
SLOW
2:00
FAST
4:07
PAUSE (:40) & DRAIN
3:00
INTERVAL DRAIN & SPIN
DRAIN/SPIN/SPRAY
FAST
C
DRAIN & SPIN
1:40
FAST
:47
FAST
4:13
OFF
7:30
WASH FILL & PAUSE
AGITATE
1:24
H,W,C
SLOW
PAUSE
AGITATE
H,W,C
SLOW
PAUSE
:47
1:36
AGITATE
DELICATE
:47
1:36
H,W,C
SLOW
PAUSE
:35
1:55
DRAIN
:30
FILL & PAUSE
W,C
2:06
DRAIN
2:00
DRAIN & SPIN
SLOW
2:00
SLOW
1:40
PAUSE
:40
RINSE FILL & AGITATE
W,C
PAUSE (:40) & DRAIN
3:00
INTERVAL DRAIN & SPIN
DRAIN/SPIN/SPRAY
SLOW
W,C
DRAIN & SPIN
1:40
SLOW
:47
SLOW
4:13
OFF
7:30
REGULAR
WASH FILL & AGITATE
H,W,C
FAST
14:55
PAUSE (:40) & DRAIN
2:40
DRAIN & SPIN
2:00
PAUSE
:40
RINSE FILL & AGITATE
W,C
FAST
PAUSE (:40) & DRAIN
3:00
INTERVAL DRAIN & SPIN
DRAIN/SPIN/SPRAY
4:07
FAST
COLD
DRAIN & SPIN
OFF
1:40
FAST
:47
FAST
4:13
7:30
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 39445 AND 201013 CYCLE SEQUENCE
46
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
PERMANENT
PRESS
WASH FILL & AGITATE
WATER
TEMP.
SELECT
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
*MOTOR
SPEED
TIME (Min.
& Sec.)
FAST
9:00
SLOW
1:12
SLOW
:15
SLOW
:45
SLOW
:15
SLOW
2:48
FAST
3:00
FAST
6:00
OFF
3:00
WASH FILL & AGITATE
H,W,C
REGULAR
SPIN
SPIN & SPRAY
C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
OFF
FAST
15:00
FAST
1:12
FAST
:15
FAST
:45
FAST
:15
FAST
2:48
FAST
3:00
FAST
6:00
3:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 200604 CYCLE SEQUENCE
201143
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
47
Cycle Sequence Charts
NOTE: Times listed are approximate.
CYCLE
FUNCTION
REGULAR
WASH FILL & AGITATE
WATER
TEMP.
SELECT
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
*MOTOR
SPEED
TIME (Min.
& Sec.)
FAST
15:00
FAST
1:30
FAST
:25
FAST
2:35
FAST
3:00
FAST
6:00
FAST
9:00
FAST
1:30
3:00
PERMANENT
PRESS
OFF
WASH FILL & AGITATE
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
W,C
SPIN
FAST
:25
FAST
2:35
FAST
3:00
FAST
6:00
OFF
3:00
DELICATE
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
WASH FILL & AGITATE
H,W,C
WASH FILL & SOAK
H,W,C
SPIN
SPIN & SPRAY
C
SPIN
RINSE FILL & AGITATE
C
SPIN
OFF
1:30
FAST
:25
2:35
FAST
:25
2:35
FAST
:25
FAST
1:30
1:05
FAST
:25
FAST
2:35
FAST
3:00
FAST
3:00
3:00
*On Single Speed Model Washers, All Speeds are Fast.
KEY:
H = HOT
W = WARM
C = COLD
TIMER NO. 200927 CYCLE SEQUENCE
48
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201143
Download PDF