Remington | 489 | Operating Instructions

REMINGTON
®
REMINGTON
Powerdriver
490-01
NDENT LAB
OR
PE
DE
ST
®
I
FO
R P U B LI C
™
Y
TE
NG
FE
T
AN
Y
OR
AT
IN
Models 489 and 490
SA
POWDER ACTUATED TOOL
MANUFACTURERS´ INSTITUTE INC.
G 029
G 028
Operating
Instructions
482-1
Important:
Read this manual and all labels carefully before operating your powder
actuated tool. This manual should always accompany the tool and be
transferred with it upon change of ownership.
INDEX
Warning: Safety Precautions ............................................................ 1-9
Why A Fastener Holds ....................................................................... 10
Selecting Fasteners and Powder Loads ............................................ 11
Operation ...................................................................................... 12,13
Parts List ............................................................................................ 14
Accessories ........................................................................................ 14
Barrel Replacement ........................................................................... 15
Tool Disassembly and Assembly .................................................. 16,17
Troubleshooting ............................................................................ 18,19
Fasteners ........................................................................................... 19
Application Chart ........................................................................... 20,21
Parts and Accessories ....................................................................... 21
Warranty ............................................................................... Back Cover
REMINGTON
Powerdriver Models 489 and 490
The Remington Powerdriver Models 489 and 490 are designed for use
with Remington powder 22 caliber Type A crimped loads and Remington Power Fasteners which are no longer than 2 1/2". Remington
Power Fasteners are manufactured from special steel and heat
treated to produce a very hard yet ductile fastener.
Maximum 2 1/2"
Spall Shield*
Powder Load*
Power Fastener*
REMINGTON
Trigger
Barrel Assembly
Muzzle
Recommended
Approved Eye
Protection*
490-02
* Not provided with tool.
! Warning: Safety Precautions
WARNING ICON
G 001
The following pages contain detailed warnings, cautions, and rules of safe
operation. Read carefully and become familiar before operating to avoid
serious injury. We expressly disclaim any liability for any injury to persons
or damage to property which result from your failure to take the precautions
contained in this manual.
!
WARNING: This tool is designed only for use by qualified
operators. Qualification is obtained through a thorough understanding of
the Safety Warnings and operating instructions as defined in this operating
manual. NOTE: The labor regulations of many states require that the
operator of this tool on a job site be thoroughly trained and certified for
competence prior to operating this tool. For certification procedures, call:
DESA Technical Services Department, 1-800-323-5190.
BEFORE USING
?
?
489-03
1.
489-04
ALWAYS handle the tool as if it were loaded. Before starting work, check that
the tool is unloaded and the muzzle is clear. NEVER load a tool unless it is going
to be used.
DEF
ECT
IVE
489
2.
G 018
489-06
ALWAYS inspect to make sure the tool is working properly. If the tool does not
work properly, remove from service and tag DEFECTIVE. DO NOT use the tool
again until it has been properly repaired.
G 018
3.
489-08
Operators489-07
and bystanders must ALWAYS wear ANSI/OSHA approved eye
and ear protection.
1
Safety Precautions
WARNING
POWDER
ACTUATED
TOOLS
IN USE
!
482-10
4.
489-09
ALWAYS clear the work area on all sides and post appropriate warning signs
on job sites.
G 018
482-12
489-10
5.
ALWAYS make sure the work area is clean from loose material and debris.
HANDLING THE TOOL
G 018
1.
489-11
NEVER place your hand over the muzzle. Accidental discharge can cause
serious injury.
489-12
489-13
489-1
G 018
2.
NEVER place your finger on the trigger until the muzzle of the tool is against the
work surface.
2
Safety Precautions
POWD
LOAD POWDER
LOADS
G 018
489-15
3.
489-16
ALWAYS store UNLOADED powder actuated tool and powder loads in a
locked container. Keep powder loads of different power levels in separate
containers.
G 018
4.
489-17
NEVER carry or pass a loaded powder actuated tool. NEVER point a powder
actuated tool at anyone.
G 018
489-18
5.
489-20
If the tool is dropped, inspect for damage and repair it before continuing to work.
NEVER use a damaged tool.
G 018
489-22
6.
ALWAYS take precaution to maintain your balance while operating a powder
actuated tool.
3
Safety Precautions
?
?
?
G 018
7.
An operator taking medication should take extra precautions while handling the
tool. NEVER drink alcoholic beverages or take medications which impair your
vision, balance or judgement before using a powder actuated tool.
KNOW YOUR FASTENING BASE MATERIAL
?
Sinks in
with
average
hammer
blow
?
?
?
CENTER
PUNCH TEST
TOO SOFT
G 018
482-28
482-27
482-26
Start
Point
flattens
Surface
shatters
TOO HARD
G 018
482-29
1
GRAY
TOO BRITTLE
G 018
3
GREEN
2
BROWN
4
YELLOW
482-30
482-31
1.
ALWAYS know the thickness and type of base material into which you are
fastening. NEVER GUESS. Test the base material by using the Center Punch
Test. The Center Punch Test is performed by using a hammer to test drive the
particular power fastener to be used into the material. If the point penetrates
easily, the material is too soft. If the point becomes blunt, the material is too
hard. If the material fractures, cracks or shatters, the material is too brittle. Test
fastenings can be made if the material shows a clear fastener impression and
the fastener point is not blunted. Always start with the lowest powder load
(Gray-Level 1) and proceeding with the order shown in the lower right-hand
figure above. ALWAYS wear approved eye protection.
4
Safety Precautions
CAST IRON
GLASS
G 018
TILE
BRICK
G 018
482-33
2.
489-24
NEVER attempt to drive power fasteners into very hard or brittle materials
including, but not limited to cast iron, glass, tile, stone, brick, or hardened steel.
Materials of this type tend to shatter and create hazard from flying particles.
489-25
G 018
3.
NEVER make fastenings in spalled or cracked areas.
489-26
G 018
4.
NEVER drive power fasteners into thin or easily penetrated material unless it
is backed by concrete or steel. When in doubt, such as when base material is
concealed, conduct a Center Punch Test (See page 4). Check continually to
avoid fastening into unsuitable material, especially in older buildings.
489-27
5.
489-28
G 018
DO NOT fasten thru or within 1/2" of predrilled or pre-punched holes.
5
Safety Precautions
3"
3"
3"
3"
1X
3X
482-39
482-38
6.
DO NOT drive power fasteners into concrete less than three times as thick as
the intended fastener penetration, within 3" of the edge, within 3" of another
power fastener, or within 3" of a failed power fastener.
WELD
1"
1/2"
482-40
TOO THIN
3/16" MIN
482-41
G 018
7.
DO NOT drive power fasteners into steel base material less then 3/16" thick,
within 2" of a weld, within 1/2" of the edge, or within 1" of another power fastener.
NO
G 018
YES
489-29
8.
When fastening into masonry walls, always drive into horizontal mortar joints,
NEVER into vertical mortar joints. BE CAREFUL. A poorly laid joint may permit
too much penetration and/or unsatisfactory holding power.
OPERATING THE TOOL
90˚
1.
ALWAYS hold tool perpendicular to work surface.
6
Safety Precautions
30
4892.
489-33
Should the tool fail to fire, hold the muzzle firmly against the work surface for
30 seconds. Release the trigger and remove pressure on the tool while holding
the muzzle against the work surface. Again press the tool firmly against the
work surface and pull the trigger. If the tool still fails to fire, hold the tool firmly
against the work surface for another 30 seconds before unloading and carefully
discarding the misfired powder load into water or oil.
G 018
3.
WATER
Spall
Shield
489-34
ALWAYS use the spall shield when driving directly into concrete or steel.
ALWAYS wear eye protection.
GAS
GASOLINE
OLINE
G 018
482-50 G 018
482-49
4.
NEVER use a powder actuated tool in an explosive or flammable atmosphere
or when non sparking tools are required.
POWDER LOADS AND FASTENERS
DER
POW DS
LOA
DER
POW DS
LOA
G 018
G 018
482-51
1.
NEVER leave unfired powder loads on floors or work surfaces.
7
Safety Precautions
Start
22
CALIBER
6
2
BROWN
3
GREEN
5
4
3
2
7
1
1
4
YELLOW
482-31
2.
8
9
10
11
12
NICKEL
BRASS
1
GRAY
482-54
NOTE:
Failure to start with
the lowest power
level can result in
overdrive condition
and will result in
damage to tool
(see page 11).
Remington Powder Loads are available in four power levels with gray (1) being
the lowest power level and yellow (4) being the highest power level. Always start
with the lowest power level (gray-level 1) and increase until a proper fastening
is made (see page 11 “Selecting Fasteners and Loads”).
DER
POW DS
LOA
DER
POW DS
LOA
482-55
G 018
482-56
G 018
3.
NEVER use powder loads in firearms.
POWDER
LOADS
ONLY
482-57
4.
NEVER carry fasteners or other hard objects in the same pocket or container
with powder loads.
YELLOW?
BROWN?
GREEN?
GRAY?
G 018
482-58
5.
A color blind person must take extra precautions to prevent the chance of
mixing the powder loads of various levels.
8
Safety Precautions
G 018
482-59
6.
Power fasteners are a permanently installed fixture. An act of demolition is
required for their removal. Appropriate safety precautions must be taken.
Head
Shank
Plastic Flute
7.
482-60
NEVER use common nails or other materials as fasteners. Remington Power
Fasteners are manufactured from special steel and heat treated to produce a
very hard yet ductile fastener.
G 018
482-61
8.
NEVER pry a powder load out of the chamber. Prying can discharge the load
causing serious injury (see Troubleshooting Guide on pages 18 and 19).
LOAD
1
9.
2
2
UNLOAD
1
REMINGTON
REMINGTON
489-36
489-37
ALWAYS insert the power fastener first, then the powder load. If work is
interrupted for any reason, ALWAYS remove the powder load before removing
the power fastener (see page 13 item 7).
9
Why A Power Fastener Holds
WHY A POWER FASTENER HOLDS
IN CONCRETE
The compression bond of the concrete to the power
fastener accounts for the majority of the holding power.
The fastener displaces the concrete which tries to return
to its original form causing a squeezing effect.
Maximum holding power is achieved when the
depth of penetration produces a bond on the power
fastener equal to the strength of the concrete. As a
general rule, penetration should be approximately 1"
to 1 1/4" into the base concrete. Make sure the concrete
is at least three times as thick as the intended fastener
penetration. NEVER have the power fastener point protrude thru the concrete.
482-64
NOTE: Concrete needs to cure for 28 days before
maximum fastening holding power will be achieved.
WHY A POWER FASTENER HOLDS IN STEEL
Holding power in steel depends on the elasticity of
the steel. The steel pushes back on the shank of the
power fastener.
Drop a marble into water; the water parts, the
marble continues down, the water closes back. This is
similar to the reaction when a power fastener penetrates
steel.
In steel, the point of the power fastener must
penetrate completely through for highest holding power.
If the fastener does not penetrate, the spring action of the
steel pushes back on the point and tends to force the
fastener out.
Recommended applications are between 3/16-3/8"
steel.
NOTE: When fastening in steel be sure the point goes
thru the steel.
10
482-65
Selecting Power Fasteners
and Powder Loads
FASTENING INTO CONCRETE
The proper power fastener length can be determined
by adding the thickness of the material to be fastened and
the amount of fastener that will actually penetrate the
concrete. The concrete must be three times as thick as the
intended fastener penetration. In most cases, penetration
should be approximately 1" to 1 1/4" into the base concrete
material.
482-85
Wood or Non-Metals
To Concrete
FASTENING INTO STEEL
The proper fastener length can be determined by
adding the thickness of the material to be fastened and the
thickness of the steel. The point of the power fastener
must go completely through the steel.
482-79
Wood or Non-Metals
To Steel
POWDER LOADS
Always start with the lowest power level (gray-level
1). If the first test fastener does not penetrate to the
desired depth, move to the next highest power level
(brown-level 2). Increase until a proper fastening is made.
IMPORTANT: Damage to the tool will result if the above
instructions are not followed (see illustrations to right and
lower right).
OVERDRIVEN POWER FASTENERS
AND PISTON
An overdriven power fastener results when too
strong of a powder load is used causing the piston to
extend past the muzzle. Move to the next lightest powder
load. Repeated overdrive will damage your tool. By avoiding overdrive, you can extend the life of your tool considerably and avoid costly repairs.
NOTE: NEVER fire the tool without a power fastener. This
can damage the tool and/or cause possible injury to the
operator.
IMPORTANT: DO NOT use power fasteners longer than
2 1/2". Fasteners longer than 2 1/2" will cause load
ejection problems.
11
RIGHT
482-66
Flush With Surface
OVERDRIVE
482-67
G 018
Piston Extended
Out of Muzzle
Operation
48
489-3
1.
Grasp muzzle and slide barrel forward rapidly until it stops. This sets piston into
firing position and opens the chamber.
482-70
2.
482-71
Insert power fastener into muzzle of tool, head end first. Push the fastener until
point is even with end of tool. ALWAYS load the fastener first, then the powder
load.
482-72
3.
482-73
Select the proper Remington Powder Load (see Application Chart on pages 20
and 21) and insert into the chamber until it stops.
489-3
4.
NOTE:
Failure to start with
the lowest power
level can result in
overdrive condition
and will result in
damage to tool
(see page 11).
Push barrel into housing to the closed position.
12
Operation
90˚
489-40
5.
Place the muzzle of tool perpendicular to work surface without tilting the tool.
Push tool against work surface until sliding action of barrel stops.
489-41
6.
Squeeze trigger to set power fastener. Be sure to keep pressure on tool during
this operation.
489
7.
After fastening is made, slide barrel forward rapidly. This motion ejects the
spent powder load and resets the piston for the next fastening. Make sure spent
load has ejected from tool.
30
WATER
489489-33
8.
Should the tool fail to fire, hold the muzzle firmly against the work surface for
30 seconds. Release the trigger and remove pressure on the tool while holding
the muzzle against the work surface. Again press the tool firmly against the
work surface and pull the trigger. If the tool still fails to fire, hold the tool firmly
against the work surface for another 30 seconds before unloading and carefully
discarding the misfired powder load into water or oil.
13
Parts List
7
3
9
14
18
5
15
16
2
19
1
13
20
17
8
10
6
4
12
11
Key
No.
Part No.
489
Part No.
490
490-03
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
TA4000
076659
076620-02
076630-02
078334
076943
098679-01
075370
044279
098720-02
055436
077183
076674
077277
076657
077191
056217
056218
076671
077708
TA4000
076659
076620
076630
078334
076943
098679-01
075370
044279
098720-01
055436
077183
076674
077277
076657
077191
056217
056218
076671
077708
BARREL, Assembly and Piston
BREECH
HOUSING, Handle, Right
HOUSING, Handle, Left
LINK, Trigger
NUT, Pad Recoil
PAD, Recoil
PIN, Firing
PIN, Spring
RECEIVER, Assembly
SCREW, Barrel
SCREW, Breech
SCREW, Housing
SCREW, Housing
SEAR
SPRING, Breech
SPRING, Pin, Firing
SPRING, Sear
TRIGGER
PAD, Pressure Assembly
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
2
6
1
1
1
1
1
1
ACCESSORIES
Part No.
Description
058972
056415
056485
056486
103754
SHIELD, Spall
GOGGLES
BRUSH, 1/4"
BRUSH, 5/8"
HEX WRENCH, 3/16"
IMPORTANT: Do not use key numbers when ordering service parts. Always order
components by part number and description. Include Model and Serial numbers.
14
Barrel Replacement
!
WARNING ICON
G 001
WARNING: Never disassemble, replace barrel, clean, or assemble a powder
actuated tool while it is loaded.
B
REMINGTON
D
C
A
REMINGTON
489-43
REMINGTON
48
489-45
1.
Remove front screw (A). Slide barrel assembly (B) from receiver (C). Remove
pressure pad assembly (D).
B
E
489-46
2.
If tool has been overdriven, tap piston
(E) on a hard surface until the piston is
489-47
pushed back into the muzzle. Inspect the barrel assembly (B) and replace if
damaged.
489-48
489-49
3.
A
F
REMINGTON
489-50
To assembly, push piston all the way into the barrel. Slide the barrel assembly
into the receiver. Turn barrel to line up slot (F) with front screw hole (A).
D
REMINGTON
A
489-51
4.
Insert screw (A) and tighten. Insert and tighten pressure pad assembly (D).
15
16
G
M
H
N
I
J
R
T
Q
490-04
S
U
O K
P
L
V
F
D
A
C
E
B
Tool Disassembly
And Assembly
TOOL DISASSEMBLY
1.
Remove screw (G) from recoil pad (H). Lift pad away from handle. Separate
housing halves by removing the seven housing screws (I & J).
2.
Remove receiver (C), firing pin (K), firing pin spring (L), sheet metal nut (M),
trigger link (N), link pin (O), sear (P), and trigger (R).
3.
Push barrel assembly (B) into receiver (C). Remove screw (S) from receiver.
Remove front screw (A), pressure pad assembly (D), barrel assembly (B),
breech (T), and breech spring (U).
4.
Clean your tool after each days use by using a penetrating lubricant such as
“WD-40” sparingly and wipe dry. Brushes are available through your distributor
to aid in cleaning.
TOOL ASSEMBLY
1.
Push the piston (E) all the way into the barrel (B). Insert breech spring (U), the
breech (T) and barrel assembly (B) into the receiver (C). Make sure the breech
slot (V) in the breech (T) is aligned with the hole for breech screw (S).
2.
Push the barrel assembly (B) forward until the breech slot (V) is visible through
the hole for breech screw (S). Insert and tighten breech screw (S). Align barrel
slot (F) with hole for front screw (A). Insert and tighten front screw (A). Insert and
tighten pressure pad assembly (D).
3.
Insert link pin (O) into housing half. Assemble sear spring (Q) in pocket of
breech (T). Insert sear (P) into breech with solid leg facing forward and keyhole
leg down. Assemble small end of firing pin spring (L) onto end of firing pin (K)
and insert into rear of receiver (C).
4.
Place breech end of receiver into housing. Assemble trigger link (N) on link pin
(O) with angled end of trigger link up over sear (P).
5.
Assemble trigger (R) into housing half. Insert sheet metal nut (M) into housing
pocket with hollow side towards grip. Assemble housing halves.
6.
Insert short screws (I) into handle bottom. Longer screws (J) into remaining
holes in side of housing. Tighten uniformly.
7.
Assemble upper part of recoil pad (H) into housing. Insert screw (G) into lower
part of recoil pad (H) and tighten.
8.
Test tool without powder load by depressing barrel against work surface, pulling
trigger, and releasing tool. Test several times to insure that the firing mechanism operates freely.
17
Troubleshooting Guide
PROBLEM
POSSIBLE CAUSE
REMEDY
Piston hangs out
of muzzle.
Tool overdriven.
Tap piston on a hard surface
until piston is pushed back
into the muzzle (see “Overdriven Fastener” below).
Piston not properly assembled in relation to barrel
screw.
Remove barrel assembly.
Follow instructions for barrel
replacement (see page 15).
Replace all damaged or
missing parts.
Replace barrel assembly or
take tool to your distributor.
Broken piston.
Change either to next lower
powder load or next longer
length fastener.
Overdriven fastener.
Excessive power.
Piston jammed.
Overdriving of fastener (see
Remove barrel assembly.
Follow instructions for barrel
replacement (see page 15).
Replace other parts if damaged.
above).
Expended load will
not extract.
Clean chamber. If loads will
not chamber with slip-fit or
extraction difficulties continue, take tool to your distributor.
Dirty or damaged chamber.
Broken ejector.
Reduction or loss
of power.
Tool does not
completely depress.
Replace barrel assembly or
take tool to your distributor.
Pins being used are over
2 1/2" long.
Use proper pin size.
Piston not returning to full
rear position.
Barrel must be snapped to
the full extended position to
properly position piston
against breech.
Worn piston ring or broken
piston.
Replace barrel assembly or
take tool to your distributor.
Misassembled or damaged
breech and firing pin parts.
Remove breech and check
all parts for correct fit assembly.
Failure of tool to depress
completely.
See data listed under “Tool
does not completely depress,” above.
Tool does not fire.
18
Troubleshooting Guide (cont.)
PROBLEM
POSSIBLE CAUSE
REMEDY
Tool does not fire.
Dirt build-up on breech not
allowing proper penetration
of firing pin.
Check firing pin indentation
on cartridge. Clean breech,
breech face, sear and firing
pin. Replace worn or damaged parts.
Opening and closing of barrel or
pushing down on
the tool, etc. is not
smooth but is
rough or binds.
Lack of proper cleaning.
Inspect and clean complete
tool. Replace worn or damaged parts.
Fasteners
482-79
Wood or Non-Metals
To Steel
482-78
482-80
Wood or Non-Metals
To Concrete
Fasten wood or non-metals to concrete or steel.
SP FASTENERS
IMPORTANT
This tool is designed to use 22 caliber necked-down crimped
loads, power levels 1 (gray) through 4 (yellow).
5/8"
G 018
Straight Wadded
Load
Necked-Down
Crimped Load
WARNING ICON
G 001
CAUTION
Do not use any load other than the 22 caliber neckeddown crimped load. Other types of loads will cause loadejection problems.
19
Application Chart
Powder load and power fastener application information.
For fastening this
power fastener
length
to this
powder load
color
Two by fours
Concrete
Cement block
Steel (3/16" to 3/8" thick)
2 1/2"
2 1/2"
2"
Green
Green
Yellow
Furring strips
Concrete
Cinder block
Cement block
Steel (3/16" to 3/8" thick)
1 1/2"
1 1/2"
1 1/2"
2"
Green
Gray
Brown
Yellow
Electrical
junction boxes
Concrete
Cement block
Steel
1"
1"
3/4"
Green
Brown
Green
Conduit clips
Concrete
Cement block
Cinder block
Steel
1"
1"
1"
3/4"
Green
Brown
Gray
Green
Shelf brackets
Concrete
Cement block
Cinder block
1"
1"
1"
Green
Brown
Gray
1/4" Plywood or
pegboard
Concrete
Cement block
Steel
1 1/4"
1 1/4"
1"
Green
Green
Yellow
Powder load listings are recommendations only. If you are in doubt, try a test
fastening using the next lightest powder load.
482-81a
Power fasteners and powder loads are available in poly packages of 10, blister
packs of 25 and cartons of 100.
IMPORTANT
• Recommended for use with Remington powder loads and power fasteners.
• Do not use power fasteners longer than 2 1/2".
• If power fastener goes below the top surface of the board, use penetrating control
disc (see illustration below).
• Always wear approved eye and ear protection.
*
Use power fastener with penetration control disc, part number 015549.
482-90
20
Application Chart
Load
Stock
Level
22 CALIBER
Number Number
Type A crimp
A22C1
1
loads for
A22C2
2
powder
actuated tools
A22C3
3
482-89 A22C4
4
Load
Strength
light
medium
heavy
extra heavy
Color Code
Case
Body
Head
brass
Gray
brass
Brown
brass
Green
brass
Yellow
Parts and Accessories
Not Under Warranty
Contact authorized dealers of this product. If they can’t supply original replacement part(s), either contact your nearest Parts Central (see below) or call DESA
International’s Parts Department at 1-800-972-7879.
When calling DESA International, have ready
• model number of your tool
• replacement part number
REMINGTON IPAT PARTS CENTRALS
RAILWAY DISTRIBUTORS
264 Railway Avenue
Campbell, CA 95008
408-866-9266
Guy Bothelho
ALL TOOL & FASTENER
7830 N.W. 72nd Avenue
Miami, FL 33166
305-888-6909
Parts Department
PRECISION TOOL
431 Commerce Park Drive
Suite 106
Marietta, GA 30060
404-421-0688
Bob Young
PORTABLE HEATER PARTS
342 No. County Road 400 East
Valparaiso, IN 46383
219-462-7441
1-800-362-6951
MASTER SERVICE CENTER
1184 Wilson NW
Grand Rapids, MI 49504
US 1-800-446-1446
616-791-4760
Mike Fowler
21st CENTURY
RD 2, Box 165
Perkasie, PA 18944
215-795-0400
1-800-325-4828
Parts Department
BLUEBONNET TOOL
10490 Shady Trail
Suite 104
Dallas, TX 75220
214-358-2363
W.C. Perry
21
Limited Warranty Agreement
DESA International warrants the Remington Powerdriver Models 489 and 490
against defects in materials and workmanship for a period of one (1) year from the
date of purchase.
If within one (1) year from the purchase date this Powder Actuated Tool fails due to
a defect in material or workmanship, DESA will repair or replace the tool at DESA’s
option. To obtain service under this warranty, contact DESA at the number/address
listed below. You must have the Serial Number, Model Number, date of purchase
and indicate the type of problem being experienced. DESA will send replacement
part(s), repair, or replace the tool at DESA’s option. However, this warranty does not
cover failures caused by misusing or abusing the product (for proper use of this
product, read and understand the operating instructions in this owners manual).
Repairs made because of misuse, abuse, negligence, or accident will be charged for
at regular repair prices.
This express and limited warranty is the only warranty on this product, and to the full
extent permitted by law there are no other warranties, express or implied, including
warranties of merchantability and/or fitness for a particular purpose which extend
beyond the terms of this express and limited warranty.
To the full extent permitted by law, the liability of DESA for personal injury, property
damage, or any other damage whatsoever, including consequential and incidental
damages, arising from the sale or use of this product shall not exceed the purchase
price of this product.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
For information about this warranty write:
DESA
®
INTERNATIONAL
P.O. Box 90004
2701 Industrial Drive
Bowling Green, KY 42102-9004
U.S.A. ONLY
For Technical Assistance or Repair on Your
Remington Powder Actuated Tool, Call
Technical Services Department
1-800-323-5190
For Certification Procedures, Call
Technical Services Department
1-800-626-2237
098714-01
REV. F
6/93
Download PDF