Sigma | S2Ba | Operating instructions | Sigma S2Ba Operating instructions

ProMinent
®
Ver
s
ion
10.
03
Operating Instructions
ProMinent® Sigma/ 2
S2Ba (Basic Type)
S2Ca (Control Type)
STOP
START
S2Ba
S2Ca
S2Ba
___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___
S2Ca
___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___
Please enter the identity code of the device here.
Two sets of operating instructions are necessary to ensure the ProMinent® Sigma/ 2 S2Ba or S2Ca metering pumps
are operated safely and reliably for their intended purpose:
This product specific Sigma/ 2 operating instructions manual and the ”General operating instructions
ProMinent® motor-driven metering pumps and hydraulic accessories” are only valid if read together!
Please completely read through these operating instructions first! · Do not discard!
The warranty shall be invalidated by damage caused by operating errors!
Part No. 987282
ProMinent Dosiertechnik GmbH · 69123 Heidelberg · Germany
BA SI XXX XX/XX GB
Control elements and key functions
Control elements: overview
4
3
2
1
5
16
6
7
8
9
10
15
14 13 12
11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Operating light (green)
Warning light (yellow)
Error warning light (red)
Stroke length adjuster
LCD display
UP key
DOWN key
P key
STOP/START key
i key
Relay output (optional)
Metering monitor socket
Float switch socket
External control socket
Diaphragm rupture indicator socket
Mains switch
Key functions
In continuous display mode
(operating)
In settings mode
(settings)
Stop pump,
start pump
Stop pump,
start pump
Press briefly
Start batch (in “batch” operating mode only),
Cancel error
Confirm entry- jump to next menu
option or continuous display
Press for 2 s
Press for 3 s
Press for 10 s
Press for 15 s
Change to settings mode
--Software version displayed
Load factory settings (calibration)
--Jump to continuous display
Press x1
Toggle between continuous displays
Toggle between “change individual digits”
and change a figure"
Press x2
---
For “change individual digits”:
jumps to first digit
Press separately
(until “Set” appears)
Change directly alterable values
Select other settings,
change individual digit or figure
Press simultaneously
Prime (in “stroke rate” permanent display)
---
STOP/START key
STOP
START
Press briefly
P key
P
---
i key
i
Arrow keys UP and DOWN
Operating-/Settings Diagram
Continuous
display
Start/stop pump
STOP
START
1 = Lock (CODE 1)
2 = Lock (CODE 2)
2
Change directly alterable values
Prime
P
P
Start batch (in"batch" operating mode only)
Cancel error
Check adjustable values
i
p. 2
Analog
P
2s
1
mode
Select the operating mode here first,
then carry out the settings in the SET menu.
mode
Exceptions: Timer and PROFIBUS®.
Manual
mode
Analog Manual Contact Batch
P
mode
p. 44
mode
none
code
P
Contact
code1
P
p. 51
Batch
P
0
P
code2
Analog
P
Set
analg
p. 45
P
Analog
Set
o 20
4 20
mA
0
P
9
P
9
P
-----
Analog
mA
Set
curve
Analog
Set
0
P
9
9
Set
set
0
P
P
Analog
P
Set
Analog
Set
i10
Analog
Set
i11
Set
P
mA
Set
f10
Freq.
f11
Freq.
Set
P
Analog
Set
i20
Set
i22
Set
P
mA
Set
f20
Freq.
next page
Freq.
f1 9
Freq.
i2 9
f21
Freq.
P
P
mA
f1 0
Freq.
f1 9
Freq.
P
Analog
Set
i2 0
Analog
mA
Set
P
i2 9
mA
P
Analog
mA
Set
f2 0
Freq.
f2 9
Freq.
mA
f2 0
Freq.
f2 9
Freq.
Analog
Set
P
Set
eroff
Analog
Set
P
er on
Analog
Analog
Analog
Set
P
Analog
Set
Analog
Set
Analog
Set
Set
Analog
Analog
Set
mA
f1 0
i2 0
i1 9
mA
Analog
Analog
mA
Analog
Set
P
Analog
Analog
Set
Set
Analog
Analog
Set
i1 9
i1 0
Analog
mA
Analog
Analog
Set
i1 0
Analog
mA
Set
P
previous page
p. 49
p. 49
p. 50
Calib
Set
Set
Set
P
Set
Set
p. 34
p. 51
p. 51
p. 51
Calib
Set
Set
Set
&
Stop
Analog
Stop
Analog
Stop
Analog
$#
i
i
ANJ
i
mA
%
i
!$&
!$&
$#
Stop
Manual
i
Stop
Manual
i
Stop
Analog
i
L
!#$
Stop
Manual
!#$
Stop
Analog
i
i
N
%#
L /h
Stop
Manual
%#
Stop
Analog
i
&
Stop
Manual
L
N
L /h
Freq.
%
i
Operating mode "Manual"
i
Stop
Analog
Freq.
Operating mode "Analog" 0-20 mA
= UP and/or DOWN arrow keys, directly alterable values
Stroke length
Factor
Batch size/
Litres remaining
Strokes remaining
Signal current
"External" display
Total litres
(feed quantity)
Total stroke number
Feed rate
Stroke rate
Continuous
display
Continuous display
i
Contact
i
Contact
Stop
Stop
Stop
Contact
Contact
Contact
$#
i
#
i
#
i
ANJ
Stop
!$&
Stop
*
*
L
N
N
Freq.
%
i
i
Stop
Stop
i
#
i
ANJ
Stop
Mem
Stop
Stop
$#
i
#
i
Mem
Mem
Mem
i
!$&
Stop
!#$
Stop
i
&
Stop
%
Batch
*
Batch
*
L
Batch
*N
Batch
Batch
L
Batch
N
Batch
Freq.
Batch
i
Operating
with
Operating mode
mode "Batch"
”Batch” with
memory and
and transfer
tansfer factor 5
"Mem" appears only when "memory" function activated
Mem
Mem
Mem
Contact
!#$
Stop
i
Contact
&
Stop
Operating
with
"Contact" with
Operating mode
mode ”Contact”
memory and
and transfer
tansfer factor 5
Dulcodes UV-Desinfektionsanlage
Imprint
Imprint
Operating Instructions for ProMinent® Sigma/ 2 S2Ba/S2Ca
© ProMinent Dosiertechnik GmbH, 2002
ProMinent Dosiertechnik GmbH
Im Schuhmachergewann 5-11
69123 Heidelberg · Germany
info@prominent.de
www.prominent.de
Subject to technical modifications.
Page 6
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Table of contents
Page
Device Identification/Identcode
®
ProMinent
9
1
Notes on safety of ProMinent ® metering pumps
11
1.1
Summary of additional safety instructions for the EX version
of the pump (in accordance with ATEX)
11
1.2
General notes
13
1.3
Notes on installation, start-up and operation
13
1.4
Notes on maintenance and repair
14
2
Product description S2Ba/S2Ca
15
2.1
Identification of pump type
15
2.2
Design/Functional description
15
2.2.1
Functional description, drive
15
2.2.2
Stroke movement
16
2.2.3
Metering capacity diagram
17
2.2.4
Functional description, delivery unit
19
2.2.5
Integrated overflow valve with bleeder function
20
2.2.6
Diaphragm rupture sensor
22
3
Technical data
25
3.1
Technical data Sigma/ 2
25
3.1.1
Capacity data
25
3.1.2
Dimensions Sigma/ 2
27
3.1.3
Dimensions Sigma/ 2 with stroke adjustment motor
27
3.1.4
Motor data
28
3.1.5
Stroke actuator drive mechanism
28
3.1.6
Stroke adjuster drive mechanism
28
3.1.7
Electrical data, stroke sensor “Sigma”
28
3.1.8
Electrical data, pacing relay “Sigma”
29
3.1.9
Sound intensity level
29
4
Start-up/Maintenance
30
4.1
Start-up
30
4.2
Maintenance
30
4.3
Replacement of wearing parts
31
5
Features of the S2Ca metering pumps
33
5.1
Function description, motors
33
5.2
Function description, controller
33
5.3
Sockets, symbols and wiring diagram
35
5.4
Retrofitting relays
41
Page 7
Dulcodes UV-Desinfektionsanlage
Table of contents
6
Control elements
42
7
Settings
43
7.1.
Check adjustable values
44
7.2
Change to settings mode
44
7.3
Select operating mode (MODE menu)
44
7.4
Settings for operating mode (SET menu)
45
7.4.1
Settings for “manual” operating mode
45
7.4.2
Settings for “analogue” operating mode (ANALG menu)
45
7.4.3
Settings for “contact” operating mode (CONTCT menu)
47
7.4.4
Settings for “batch” operating mode (BATCH menu)
49
7.5
Page 8
Settings for programmable functions (SET menu)
50
7.5.1
Settings for “calibration” function (CALIB menu)
50
7.5.2
Settings for “auxiliary frequency” function (AUX menu)
51
7.5.3
Settings for the “flow” function (FLOW menu)
51
7.6
Setting code (CODE menu)
51
7.7
Cancel total stroke number or total litres (CLEAR window)
51
8
Operating
52
8.1
Manual operation
52
8.2
Remote control
53
9
Troubleshooting
53
10
Decommissioning and disposal
55
11
Spare parts and accessories
56
Annex
57
Motor data sheet
57
EC Declaration of Conformity
58
Exploded diagrams of liquid ends
59
Stroke actuator wiring diagram
63
Wiring diagram, stroke length adjuster
63
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Identcode ordering system
Identcode ordering system
Please enter the identcode on the device label into the grey box below.
S2Ba
S i g m a B a s i c Ty p e ( S 2 B a )
HM
Main drive, diaphragm
16050
16090
16130
12050*
12090*
12030*
07120
07220
04350
Pump type: (figures 1+2 = back pressure [bar], figures 3-5 = feed rate [l/h])
16 bar; 50 l/h
16 bar; 90 l/h
16 bar; 130 l/h
10 bar; 48 l/h
10 bar; 86 l/h
10 bar; 125 l/h
7 bar; 120 l/h
7 bar; 220 l/h
4 bar; 350 l/h * for SST versions, max. 12 bar
PV
SS
Liquid end materials:
PVDF
Stainless steel
T
Seal material:
PTFE seal
0
1
Diaphragm:
Standard diaphragm, PTFE version
Double diaphragm with diaphragm rupture indicator (retro fit possible)
0
1
4
5
Liquid end version:
No spring
With 2 valve springs, Hastelloy C, 0.1 bar
With pressure relief valve, Viton® seal, no valve spring
With pressure relief valve, Viton® seal, and valve spring
0
1
2
3
4
7
8
Hydraulic connection:
Standard threaded connector (according to technical data)
Union nut and PVC insert
Union nut and PP insert
Union nut and PVDF insert
Union nut and stainless steel insert
Union nut and PVDF hose nozzle
Union nut and stainless steel hose nozzle
0
1
Version:
With ProMinent® logo (standard)
Without ProMinent® logo
S
M
N
L
P
R
V
Z
1
2
3
4
Electrical power supply:
3 ph, 230 V/400 V 50/60 Hz, 0.18 kW
1 ph, AC, 230 V/50/60 Hz, 0.18 kW
1 ph, AC 115 V 60 Hz, 0.18 kW
3 ph, 230 V/400 V, 50 Hz, (EExe, EExde)
3 ph, 230 V/400 V, 60 Hz, (EExe, EExde)
3 ph, variable speed motor, 230/400 V, 0.37 kW
Variable speed motor with integrated speed control 1 pH,
230 V, 50/60 Hz
1 ph, variable speed control set 1 ph, 230 V, 50/60 Hz
No motor, with B14 flange (Gr. 71 (DIN))
No motor, C 56 flange (NEMA)
No motor, B5 Gr. 63 (DIN)
No motor, B5, Gr. 70 (DIN)
0
1
2
A
Motor version:
IP 55 (standard)
Exe version (II 2G EExe II T3)
Exde version (II 2G EExde IIC T4)
ATEX type drive
0
1
2
3
Stroke sensor:
No stroke sensor (standard)
with stroke sensor (Hall sensor, no connection cable)
Pacing relay (reed relay)
Stroke sensor (Namur) intrinsically safe
0
1
2
3
4
5
6
S2Ba
___
___
___
___
___
___
___
___
___
___
___
Stroke length adjustment:
Manual (standard)
With stroke positioning motor, 230 V/50/60 Hz
With stroke positioning motor, 115 V/50/60 Hz
With stroke control motor,
0...20 mA 230 V/50/60 Hz
With stroke control motor
4...20 mA 230 V/50/60 Hz
With stroke control motor
0...20 mA 115 V/50/60 Hz
With stroke control motor
4...20 mA 115 V/50/60 Hz
___
Viton® is a registered trademark of DuPont Dow Elastomers.
®
®
ProMinent
ProMinent
Page 9
Dulcodes UV-Desinfektionsanlage
Identcode ordering system
Identcode ordering system
Please enter the identcode on the device label into the grey box below.
S2Ca
S i g m a C o n t r o l Ty p e ( S 2 C a )
HM
S2Ca
___
Power end, diaphragm
Pump typ: (figures 1+2 =back pressure [bar],figures 3-5 =feed rate [l/h])
16050 16 bar; 60 l/h
16090 16 bar; 95 l/h
16130 16 bar; 136 l/h
12050* 10 bar; 60 l/h
12090* 10 bar; 95 l/h
12130* 10 bar; 136 l/h
07120 7 bar; 148 l/h
07220 7 bar; 232 l/h
04350 4 bar; 350 l/h * for SST versions, max. 12 bar
Liquid end materials:
PV PVDF
SS Stainless steel
Seal material:
T
PTFE seal
Displacement element:
0
Standard diaphragm
1
Double diaphragm with rupture indicator incorporating “Pump stopping” function
2
Double diaphragm with rupture indicator incorporating “Pump alarm” function
Liquid end version:
0
No springs
1
With 2 valve springs,Hastelloy C,0.1 bar
4
With relief valve,Viton® seal,no valve spring
5
With relief valve,Viton® seal,with valve spring
Hydraulic connection:
0
Standard threaded connector (according to technical data)
1
Union nut and PVC insert
2
Union nut and PP insert
3
Union nut and PVDF insert
4
Union nut and stainless steel insert
7
Union nut and PVDF hose nozzle
8
Union nut and stainless steel hose nozzle
Version:
0
With ProMinent® logo
1
Without ProMinent® logo
Electrical power supply:
U
1 ph 100-230 V ±10 %, 50/60 Hz
Cable and plug:
A
2 m European
B
2 m Swiss
C
2 m Australian
D
2 m USA
Relays:
0
No relay
1
With fault indicating relay (N/C)
3
With fault indicating relay (N/O)
4
As 1 with pacing relay
5
As 3 with pacing relay
F
Power relay N/C
G
Power relay N/O
Control variant:
0
Manual + external with pulse control
1
Manual + external + pulse control
+ analogue
4
As 0 + process-timer
5
As 1 + process-timer
P
PROFIBUS®
Access code:
0
No access code
1
With access code
Metering monitor:
0
Input with pulse evaluation
1
Input with permanent contact
evaluation
Stroke length
adjustment:
0
Manual
C
Manual + calibration
___
___
___
___
___
___
___
___
___
___
___
___
___
___
Viton® is a registered trademark of DuPont Dow Elastomers.
Page 10
®
ProMinent
Dulcodes UV-Desinfektionsanlage
1
Notes on safety of ProMinent ® metering pumps
Notes on safety of ProMinent ® metering pumps
General user instructions
Please read through the following user instructions carefully! They will help you get the best use
out of the operating instruction manual.
The following are highlighted in the text:
• Enumerations
왘 Instructions
Operating guidelines:
NOTE
Notices are intended to make your work easier.
and safety guidelines:
WARNING
Describes a potentially dangerous situation. If not avoided. could cause fatal or serous
injury.
CAUTION
Describes a potentially dangerous situation. If not avoided. could cause slight or minor
injury or damage to property.
IMPORTANT
Describes a potentially damaging situation. If not avoided. could cause damage to
property.
Please also note the guidelines in “General Operating Instruction Manual for ProMinent® MotorDriven Metering Pumps and Hydraulic Accessories”!
EX-pump only: The nameplates affixed to the title page are identical to those on the pump
supplied to enable clear identification on the correct operating instruction manual for the pump.
Please give the order number and the serial number, which you will find on the nameplates of the
pump itself, in the event of any query or spare part order. This facilitates identification of the
pump.
1.1
Summary of additional safety instructions for the EX version
of the pump (in accordance with ATEX)
WARNING
• In explosion-threatened workplaces in zone 1, device category II 2G of explosion group II C
the pump may not be operated without the corresponding rating plate (and the corresponding EC conformity declaration) for pumps for explosion-threatened workplaces in
accordance with guideline 94/9/EC of the European guidelines.
• From July 1st, 2003 on, only pumps with the corresponding marking according to EC-Exdirective 94/9 may be used in industrial premises with potentially explosive atmospheres.
The explosion group, category and type of protection shown on the marking must
correspond to or exceed the conditions prevailing in the intended area of application.
• All other uses or modifications are prohibited!
• Pumps may never be operated in explosion-threatened workplaces without a corresponding rating plate (and the corresponding EC conformity declaration) for pumps for
explosion-threatened workplaces.
®
ProMinent
Page 11
Notes on safety of ProMinent ® metering pumps
Dulcodes UV-Desinfektionsanlage
• Installations in potentially explosive atmospheres must be inspected by a “accredited
qualified” person. This applies in particular also for intrinsically safe electrical circuits.
• Drive motors must be secured by an appropriate motor protection switch. A motor
protection approved for this application must be used for Ex“e”-motors. (Protection
against heating due to overload)
• Observe all relevant standards e.g. DIN EN 60079, DIN EN 50020, DIN VDE 0165 and/or
DIN VDE 0118 “Installing electrical equipment in explosion-threatened areas”!
• When installing the metering pump, observe the directives for the installation of devices
in explosion-threatened areas, e.g. for Europe the European operator’s guideline 99/92/EC
(ATEX137)*, (in Germany implemented via the new operating safety ordinance (Official
Federal Gazette for 2002, Part 1, No. 70, issued in Bonn 2.10.2002))!
* previously ElexV
• Observe documents supplied with individual electric components!
• On principle, metering pumps in potentially explosive atmospheres must be equipped
with a safety overflow valve at the outlet side of the pump (serves as protection against
overheating due to overload and against sparks produced by shock due to overload
which has led to the breakage drive parts.)
• When using with flammable media:
- Diaphragm pumps with mechanically actuated diaphragm: no additional measures
necessary, however, version with diaphragm rupture indicator, version Ex“i”*, must be
used on principle.
- For all metering pumps for metering inflammable media applies: starting up and
emptying only supervised by a competent person.
- Inflammable media may only be lifted with stainless steel liquid ends. - For exceptional
cases, where this is not possible, also PTFE with carbon may be used, our versions TT_
are made of conductive plastics. In this case, special attention must be paid by the
user due to the lower mechanical stability.
• If using the metering pump for Europe e.g. the European operator’s guideline 99/92/EC*
(ATEX 137**), (in Germany implemented via the new operating safety ordinance (Official
Federal Gazette for 2002, Part 1, No. 70, issued in Bonn 2.10.2002) and the German
dangerous chemicals ordinance))!
* previously Ex Vo, Vb F
** previously ATEX118A
• Observe also all relevant standards e.g. DIN EN 60079-10/14 and DIN EN 50020 for
installations in explosion-threatened areas!
• Note all national directives which apply to the installation!
• Wear parts (diaphragms, bearings etc.) of metering pumps used in potentially explosive
atmospheres must be replaced after having completed 90% of their nominal product life.
• The lubricant supply must be regularly checked for lubricated pumps, for instance by
checking the fill level, visual inspection for leakages etc.
• The proper general function, in particular of the drive, must be safeguarded by regular
inspections (leakages, noises, temperatures, possible discoloration due to excess
temperatures....).
• Use original spare parts should exchange become necessary!
• Check that the pressure relief valve downstream from the pump is functioning correctly!
The pressure relief valve must prevent the gearbox from being overloaded and overheating in explosion-threatened workplaces!
• When cleaning plastic parts, attention must be paid to not generating any electrostatic
charge by rubbing excessively. - see danger sign.
• These measures are the minimum protection measures specified bei ProMinent. Should
the user know about any further risks, it is his duty to eliminate them by taking
corresponding measures.
Page 12
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Notes on safety of ProMinent ® metering pumps
Safety devices
The following safety notice must be affixed to the pump (with PP, PC and PV liquid ends, acrylic
glass cover, ...)
ATTENTION
Because of danger of electrostatical
ignition use damp cloth only
for wiping plastic parts!
EC conformity declaration / certificates
The EC conformity declaration for pumps for explosion-threatened workplaces is supplied with
the pump (the copy of the EC conformity declaration for the pump itself does not apply to pumps
designed for explosion-threatened workplaces).
The EC conformity declarations, the EC series prototype test reports and the operating manuals
for the individual components are also supplied with the pump.
1.2
General notes
WARNING
• The equipment/devices may only be used for their intended purpose.
• ProMinent® metering pumps must not be assembled with parts which are not tested and
recommended by ProMinent otherwise this can lead to injury to persons and damage to
property for which no liability will be accepted!
• Pumps must be accessible at all times to facilitate operation and maintenance. Access
points must not be obstructed or blocked!
• Before carrying out any maintenance and repair work always drain off and flush out the
liquid end first if hazardous or unknown metered media are used!
• When metering hazardous or unknown liquids, always wear safety clothing (safety
goggles, gloves, ...) when working on the liquid end!
• You must observe the guidelines in this operating instructions manual and the ”General
operating instructions manual for ProMinent® motor-driven metering pumps and hydraulic
accessoires” on assembly, installation and maintenance!
1.3
Notes on installation, start-up and operation
WARNING
• The metering pump can contain water residue in the liquid end as the result of testing at
the factory!
If handling media which must not come in contact with water, all traces of water must be
removed from the liquid end before start-up! For this purpose, turn the pump through
180˚ and drain off the liquid end then flush with a suitable medium from above via the
intake connection!
• Do not connect mains voltage to the control cable!
• When operating the metering pump against a closed shut-off element on the pressure
side or in the event of pressure peaks during the metering stroke, the system pressure
can reach a multiple of the maximum permissible operating pressure that can consequently cause the pressure line to burst!
• To avoid this situation, an overflow is recommended for the purpose of limiting the
maximum permissible operating pressure of the pump or system.
• Do not connect a metal bypass line to the overflow valve on the PVT delivery unit! This
could cause cracks in the delivery unit!
®
ProMinent
Page 13
Notes on safety of ProMinent ® metering pumps
Dulcodes UV-Desinfektionsanlage
IMPORTANT
• Set stroke length only with pump in operation!
• Pull the red plug for venting the gear unit during initial operation of the Sigma/ 2 metering
pump (refer to Fig. 2, item 10)!
NOTE
• The pump must be secured in such a way that no vibrations can occur! The valves of the
liquid end must always be positioned vertically in order to ensure trouble-free operation!
• The intake and delivery lines must always be arranged such as to ensure connection at
the liquid end free of mechanical stress!
The lines must be secured such that no vibrations can occur!
• Only use the clamping rings and hose sockets intended for the relevant hose diameter as
well as original hoses with the specified hose dimensions and wall thickness otherwise
the stability and durability of the connection will not be guaranteed!
Avoid reducing hose sizes!
Observe the permissible pressure of the hoses!
• A vent with return to the supply tank is advisable when metering extremely aggressive or
hazardous media!
In addition, a shut-off valve should be provided on the delivery or intake side!
1.4
Notes on maintenance and repair
WARNING
• Only specially trained and authorized persons are permitted to carry out maintenance on
metering pumps and their peripherals!
• If hazardous or unknown metering media are used, always flush out the liquid end first
before carrying out any maintenance and repair work!
• When metering hazardous or unknown liquids, always wear safety clothing (safety
goggles, gloves, ...) when working on the liquid end!
• Always depressurize the delivery line first before carrying out any work on the pump!
Always discharge and flush liquid end!
Observe safety data sheets for metered liquid!
DANGER
• Disconnect power plug or power supply line before opening the plug!
Isolate relay option if applicable!
Check to ensure power is disconnected!
Secure pump while carrying out repairs to ensure it cannot be switched on unintentionally!
• Pumps for metering radioactive media must not be shipped through standard channels!
NOTE
The metering pump must be in a cleaned condition with the liquid end flushed if returned
for repair!
Page 14
®
ProMinent
Dulcodes UV-Desinfektionsanlage
2
Product description S2Ba/S2Ca
Product description S2Ba/S2Ca
WARNING
Use for intended purpose
• The pump is designed as a liquid medium metering pump; it serves the purpose of
metering liquid medium within the specified line system!
• In explosion-threatened workplaces in zone 1, device category II 2G of explosion group II
C the pump may not be operated without the corresponding rating plate (and the corresponding EC conformity declaration) for pumps for explosion-threatened workplaces in
accordance with guideline 94/9/EC of the European guidelines.
• From July 1st, 2003 on, only pumps with the corresponding marking according to EC-Exdirective 94/9 may be used in industrial premises with potentially explosive atmospheres.
The explosion group, category and type of protection shown on the marking must
correspond to or exceed the conditions prevailing in the intended area of application.
• Operate the pump only within the conditions described in the technical data!
• General restrictions with regard to viscosity limits, chemical resistance and density must
be observed (refer to ProMinent® chemical resistance list (catalogue or homepage))!
• All other applications or conversion are prohibited!
• The pump is not designed to meter gaseous media as well as solids.
• For pumps without EX protection: The pump is not suitable for metering combustible
liquids!
• Pumps may never be operated in explosion-threatened workplaces without a corresponding rating plate (and the corresponding EC conformity declaration) for pumps for
explosion-threatened workplaces.
• Only specifically trained and authorized personnel are permitted to operate the pump!
2.1
Identification of pump type
Fig. 1
The identity code and serial number are given in addition to the standard technical specifications.
These two numbers must always be quoted when making any enquiries as they enable distinct
identification of the type of metering pump.
2.2
Design/Functional description
2.2.1
Functional description, drive
The ProMinent® Sigma/ 2 diaphragm-type metering pump is an oscillatory displacement pump
with the stroke length adjustable in steps of 0,5 %. It is driven by electric motor (1). The rotary
drive of the electric motor is stepped down by worm gear and transmitted via the eccentric roller
(3) to the push rod (4) connected to fork (8) and converted into oscillatory movement. Return
spring (5) presses the fork with push rod positively against the eccentric roller thus producing the
return stroke. The stroke is adjusted by means of stroke adjustment knob (6) and spindle (7) by
limiting the return stroke. Stroke movement is transmitted directly to the displacement diaphragm.
Interacting with the valves, this diaphragm produces the overpressure and vacuum in the liquid
end necessary for delivery. Flow is pulsating.
In the basic type, the electric motor is normally a 3-ph extended-range AC motor (refer to Section 3
for other options).
®
ProMinent
Page 15
Dulcodes UV-Desinfektionsanlage
Product description S2Ba/S2Ca
1
5 4
10
3
8
7
6
Fig. 2
61_01-101_00_25-01
2.2.2
Stroke movement
a) Stroke progression
at max. stroke rate
and stroke length
b) At reduced stroke length
Stroke speed
+ Delivery stroke
– Intake stroke
0
180
360
Angle reduced stroke length
Fig. 3
Set stroke length dependent on the required delivery capacity.
30
%
30%
75 %
75%
0
50
25
75
20
0
0
25
5
0
5
10
Fig. 4
NOTE
A large stroke length and low metering frequency should be selected for very viscous
media!
A shorter stroke length and high frequency should be selected to achieve good mixing
properties!
Page 16
®
ProMinent
ProMinent
®
0
50
100
150
200
250
300
350
400
450
0
50
100
150
200
250
300
350
400
0
0
2
20
Stroke length in (%)
60
80
4
8
pressure in (bar)
6
10
Metering capacity diagram S2Ba HM (50 Hz)
40
S2Ba HM 12050
S2Ba HM 12090
S2Ba HM 12130
S2Ba HM 07120
S2Ba HM 07220
S2Ba HM 04350
Metering capacity diagram S2Ba HM (50 Hz)
12
S2Ba HM 12050
S2Ba HM 12090
S2Ba HM 12130
S2Ba HM 07120
S2Ba HM 07220
S2Ba HM 04350
100
14
120
Q (l/h)
Q (l/h)
450
0
50
100
150
200
250
300
350
400
450
500
0
50
100
150
200
250
300
350
400
450
500
0
0
2
20
80
Stroke length in (%)
60
100
4
pressure in (bar)
6
8
10
Metering capacity diagram S2Ba HM (60 Hz)
40
Metering capacity diagram S2Ba HM (60 Hz)
S2Ba HM 04350
12
S2Ba HM 12050
S2Ba HM 12090
S2Ba HM 12130
S2Ba HM 07120
S2Ba HM 07220
S2Ba HM 04350
120
S2Ba HM 12050
S2Ba HM 12090
S2Ba HM 12130
S2Ba HM 07120
S2Ba HM 07220
14
2.2.3
Q (l/h)
Q (l/h)
Dulcodes UV-Desinfektionsanlage
Product description S2Ba/S2Ca
Metering capacity diagram
Page 17
Page 18
Q (l/h)
Q (l/h)
0
50
100
150
200
250
300
350
400
450
0
50
100
150
200
250
300
350
400
450
0
0
2
20
4
Stroke length in (%)
60
80
6
pressure in (bar)
8
10
Metering capacity diagram S2Ca HM
40
S2Ca HM 12050
S2Ca HM 07120
S2Ca HM 12090
S2Ca HM 07220
S2Ca HM 12130
S2Ca HM 04350
Metering capacity diagram S2Ca HM
12
14
S2Ca HM 12050
S2Ca HM 12090
S2Ca HM 12130
S2Ca HM 07120
S2Ca HM 07220
S2Ca HM 04350
100
16
120
Product description S2Ba/S2Ca
Dulcodes UV-Desinfektionsanlage
ProMinent
®
Dulcodes UV-Desinfektionsanlage
2.2.4
Product description S2Ba/S2Ca
Functional description, delivery unit
The heart of the delivery unit is the DEVELOPAN® metering diaphragm (2). It hermetically seals
the delivery chamber of liquid end (4) and produces a displacement in the liquid end. The end
disc (5) made of chemically resistant plastic together with safety diaphragm (13) separates the
drive housing from the delivery unit and protects the drive from corrosion in the event of the
diaphragm failing. Delivery is based on the interaction between intake valve (1) and head valve (3)
of the same design together with the diaphragm movement. The valve balls can be supported
with springs for metering viscous media.
The connection dimensions of valves and liquid ends of the same size but with different materials
are identical. These parts can be interchanged as required.
Materials and dimensions are specified in Section 3, Technical data.
Fig. 5
3154-4
®
ProMinent
Page 19
Dulcodes UV-Desinfektionsanlage
Product description S2Ba/S2Ca
2.2.5
Integrated overflow valve with bleeder function
Task:
The task of the overflow valve is to protect the motor and gear unit against impermissible
overpressure caused by the metering pump.
This function is produced by a spring-loaded ball.
A pressure relief mechanism for the bleeder function is provided.
Design and functional description
(refer to Fig. No. 6 and 7)
Initially, the overflow valve illustrated under item 102 operates as a simple directly controlled
safety valve. As soon as the pressure set with spring item 132 is exceeded, the effective pressure
raises ball item 130. The liquid then flows off into the tank via hose connection item 128.
134
102
133
137
132
138
111
139*
112
100
110
126
200
125
201
117
127
136
128
101
130
116
114
113
131
202
115
118
203
Overflow valve Sigma/ 2 liquid end, 10 bar PVT
Identcode Type: 12050, 12090, 12130
Overflow valve Sigma/ 2 liquid end, 7 bar PVT
Identcode Type: 07120, 07220
Overflow valve Sigma/ 2 liquid end, 4 bar PVT
Identcode Type: 04350
Fig. 6
3160-4
Page 20
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Product description S2Ba/S2Ca
134
102
133
132
138
111
137
112
139*
100
129
110
126
200
140
201
141
125
117
101
136
127
113
116
114
128
130
115
118
131
202
203
Overflow valve Sigma/ 2 liquid end, 16 bar SST
Identcode Type: 16050, 16090, 16130
Overflow valve Sigma/ 2 liquid end, 12 bar SST
Identcode Type: 12050, 12090, 12130
Overflow valve Sigma/ 2 liquid end, 7 bar SST
Identcode Type: 07120, 07220
Overflow valve Sigma/ 2 liquid end, 4 bar SST
Identcode Type: 04350
Fig. 7
3161-4
IMPORTANT
• Knob item 139 must be turned in clockwise direction as far as it will go towards ”close“.
• The bypass line must always be closed and must be routed back into the supply tank.
Connection via hose connection item 128.
• Minimal overflow can occur in the bypass line when the valve operates close to the
overpressure function.
The bleeder function is achieved by turning knob item 139 in counterclockwise direction as far as
it will go towards ”open“: Priming aid for starting up pump against pressure. The force of spring
item 132 relieves ball item 130 which is controlled by the lower spring force of bleeder spring
item 133.
IMPORTANT
Once the pump has primed, turn knob item 139 in clockwise direction as far as it will go
towards ”close“! The pump is now operational.
®
ProMinent
Page 21
Dulcodes UV-Desinfektionsanlage
Product description S2Ba/S2Ca
Technical data
Corresponding to the type of pump, overflow valves are available for pressure stages pnom 4, 7,
10, 12 and 16 bar with (1.05 ... 1.15) xpnom opening pressure.
Material in contact with metered medium
Material
version
Liquid end
Suction/
discharge
connector
Seals
Balls
Springs
Integrated
overload
valve
PVT
PVDF
PVDF
PTFE
Ceramic / glass*
Hastelloy C
PDFE/Viton®
SST
Stainless steel
1.4571/1.4404
Stainless steel
1.4581
PTFE
Stainless steel
1.4404
Hastelloy C
Stainless steel/
Viton®
*for 07120, 07220, 04350
Viton® is a registered trademark of DuPont Dow Elastomers.
Use for intended purpose/Use unintended purpose
Use for intended purpose
Protect the dosing pump against unacceptable high overpressure produced by the dosing pump.
Use the overflow value only in connection with liquid with a viscosity of up to max. 200 mPa s.
IMPORTANT
• The ceramic ball and ball seat of the overflow valve are wearing parts. Slight leakage can
occur at the safety valve after a prolonged period of operation. The ball and ball seat
should be replaced if leaks occur.
• The bypass line must always be connected and must be routed back into the supply tank.
Use for unintended purpose
To protect the system from impermissible overpressure.
The pump must not be operated without the bypass line connected.
The bypass line must not be connected in the intake line (the bleeder function will no longer be
guaranteed). The bypass line must be routed back into the supply tank.
WARNING
When carrying out maintenance work on the overcurrent valve, pay attention to the
tensioned state of the pressure spring item132! Wear safety goggles!
2.2.6
Diaphragm rupture sensor
Function:
Monitors the seals in the working diaphragm. This liquid end can continue to function for a short
period in emergency mode, i.e. full operating pressure, no leakage, even after diaphragm rupture.
Design and function description (see Fig. 8)
Liquid ends with diaphragm rupture sensors comprise a standard liquid end (item 100) a working
diaphragm (item 200) and an auxiliary diaphragm (item 148) The auxiliary diaphragm is positioned
between the back plate (item 201) and the interim plate (item 147) and forms a sealed
compartment together with the working membrane (item 200).
The leak tightness of the working diaphragm, Item 200, is monitored with a diaphragm failure
detector, Item 104, that triggers a contact signal in the event of diaphragm failure so that the
pump is stopped in the S2Ca and the diaphragm failure is indicated on a LCD.
Page 22
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Product description S2Ba/S2Ca
The liquid end can continue to operate in emergency mode, i.e. full operating pressure, no
leakage, even after diaphragm rupture, until the diaphragm has been replaced. We offer two
versions of the S3Ca with diaphragm rupture sensor:
• After a working diaphragm rupture, the pump stops and an ”error“ message/diaphragm sensor
signal is given.
• After a working diaphragm rupture, the pump will continue to run. An ”error“ message/
electrical signal is given.
A function plug is supplied which allows the pump to continue operating after a fault has
occurred (diaphragm rupture, failure of the diaphragm rupture sensor).
WARNING
• EX-pump only: Installations in potentially explosive atmospheres must be inspected by a
“accredited qualified” person. This applies in particular also for intrinsically safe
electrical circuits.
• EX-pump only: observe documents supplied with the sensor!
IMPORTANT
• In the case of the S2Ba, the customer should install a diaphragm rupture signal monitor
and/or ensure that the pump will stop after a diaphragm rupture.
• In the event of diaphragm failure, a contact signal is triggered as from 2 bar system
backpressure.
• Exact pump delivery can no longer be guaranteed after failure of the working diaphragm.
• The auxiliary diaphragm, Item 148, is a wearing part and must be replaced after failure
of the working diaphragm. The diaphragm rupture sensor lens, Item 156, should be
replaced after every diaphragm rupture.
111
103
112
147
118
148
203
149
204
150
200
201
100
159
110
117
101
113
156
157
155
158
160
114
115
161
116
162
FM 130
Identcode Type: 12050, 12090, 12130, 16050, 16090, 16130
FM 350
Identcode Type: 04350, 07120, 07220
®
ProMinent
104
163
Fig. 8
3162-4
Page 23
Dulcodes UV-Desinfektionsanlage
Product description S2Ba/S2Ca
Material in contact with metered medium
Liquid end:
Parts of diaphragm failure monitor in contact with medium
PVDF
Stainless steel 1.4571
Lens, seals
Item 148, 156, 159
Intermediate disc Item 147,
intermediate bush Item 150
PTFE
PTFE
PVDF
PVDF
Electrical data for the diaphragm breakage sensor
a) Switch contact
30 V DC/1 A
or
125 V AC/0.6 A
or
250 V AC/0.3 A
The diaphragm sensor is a N/C relay.
IMPORTANT
Before commencing operation, install the provided diaphragm breakage sensor together
with the gasket (Item159) and make the electrical connections.
NOTE
• For safety reasons it is advisable to connect a safe low voltage (e.g. EN 60335-1 (SELV)).
• The cable priority is arbitrary.
b) Namur sensor, intrinsically
Blue
-
Brown
+
5-25 V DC, Namur type and/or DIN 19234, zero volt design.
Rated voltage: 8 V DC (Ri ~ 1 kΩ)
Power consumption:
Active surface, uncovered > 3 mA
Active surface, covered < 2 mA
Rated switching distance: 1.5 mm
The monitor/feeder must be capable of evaluating current changes in order to indicate
diaphragm rupture!
WARNING
• EX-pump only: Installations in potentially explosive atmospheres must be inspected by a
“accredited qualified” person. This applies in particular also for intrinsically safe
electrical circuits.
• EX-pump only: observe documents supplied with the sensor!
IMPORTANT
• Before commencing operation, install the provided diaphragm breakage sensor together
with the gasket (Item159) and make the electrical connections.
• For pump without EX protection: For safety reasons it is advisable to connect a safe low
voltage (e.g. EN 60335-1 (SELV)).
Page 24
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Technical data
3
Technical data
3.1
3.1.1
Technical data Sigma/ 2
Capacity data
Technical data S2Ba at 50 Hz operation
Feed rate at
maximum
back pressure
Pump type Sigma/
bar
l/h
Max.
stroke
rate
Suction
lift
Admissible
priming
pressure
suction side
Connection
suction /
discharge
side
Shipping
weight
ml/stroke
strokes/min.
m Ws
bar
G - DN
kg
12050 PVT
10
50
11.4
73
7
3
1"-15
15
12050 SST
12
48
11.4
73
7
3
1"-15
20
16050 SST
16
48
11.4
73
7
3
1"-15
20
12090 PVT
10
90
11.4
132
7
3
1"-15
15
12090 SST
12
86
11.4
132
7
3
1"-15
20
16090 SST
16
86
11.4
132
7
3
1"-15
20
12130 PVT
10
130
10.9
198
7
3
1"-15
15
12130 SST
12
125
10.9
198
7
3
1"-15
20
16130 SST
16
125
10.9
198
7
3
1"-15
20
07120 PVT
7
120
27.4
73
5
1
20*
16
07120 SST
7
120
27.4
73
5
1
20*
24
07220 PVT
7
220
27.7
132
5
1
20*
16
07220 SST
7
220
27.7
132
5
1
20*
24
04350 PVT
4
350
29.4
198
5
1
20*
16
04350 SST
4
350
29.4
198
5
1
20*
24
All performance data applies to water at 20 °C.
The suction lift applies when the suction line and liquid end are full and correctly installed.
* Sigma types 07120, 07220 and 04350, the valves used in the liquid end are DN 25 (G11/2). Since DN 20 is usually adequate for
this tubing (see Technical Data, connection-suction/discharge side) the connector parts to be ordered by Identcode (e.g.
washers) have already been reduced to DN 20, i.e. tubing and accessories can be DN 20.
Technical data S2Ba at 60 Hz operation
Feed rate at
maximum
back pressure
Pump type Sigma/
bar
psi
Max.
stroke
rate
Suction
lift
Admissible
priming
pressure
suction side
Connection
suction /
discharge
side
Shipping
weight
I/h/gph
strokes/min.
m Ws
bar
G - DN
kg
12050 PVT
10
145
60/ 15.9
87
7
3
1"-15
15
12050 SST
12
174
57/ 15.2
87
7
3
1"-15
20
16050 SST
16
232
57/ 15.2
87
7
3
1"-15
20
12090 PVT
10
145
108/ 28.5
156
7
3
1"-15
15
12090 SST
12
174
103/ 27
156
7
3
1"-15
20
16090 SST
16
232
103/ 27
156
7
3
1"-15
20
12130 PVT
10
145
156/ 41
232
7
3
1"-15
15
12130 SST
12
174
150/ 39.6
232
7
3
1"-15
20
16130 SST
16
232
150/ 39.6
232
7
3
1"-15
20
07120 PVT
7
100
144/ 38
87
5
1
20*
16
07120 SST
7
100
144/ 38
87
5
1
20*
24
07220 PVT
7
100
264/ 69.7
156
5
1
20*
16
07220 SST
7
100
264/ 69.7
156
5
1
20*
24
04350 PVT
4
58
420/ 111
232
5
1
20*
16
04350 SST
4
58
420/ 111
232
5
1
20*
24
All performance data applies to water at 20 °C.
The suction lift applies when the suction line and liquid end are full and correctly installed.
* Sigma types 07120, 07220 and 04350, the valves used in the liquid end are DN 25 (G11/2). Since DN 20 is usually adequate for
this tubing (see Technical Data, connection-suction/discharge side) the connector parts to be ordered by Identcode (e.g.
washers) have already been reduced to DN 20, i.e. tubing and accessories can be DN 20.
®
ProMinent
Page 25
Dulcodes UV-Desinfektionsanlage
Technical data
Technical data S2Ca
Feed rate at
maximum
back pressure
Max.
stroke
rate
Suction
lift
Admissible
priming
pressure
suction side
Connection
suction /
discharge
side
Shipping
weight
Pump type Sigma/
bar
l/h
ml/stroke
strokes/min.
m Ws
bar
R - DN
kg
12050 PVT
10
145
60/ 16
90
7
2
1"-15
17
12050 SST
12
174
60/ 16
90
7
2
1"-15
22
16050 SST
16
232
60/ 16
90
7
2
1"-15
22
12090 PVT
10
145
95/ 25
160
7
2
1"-15
17
12090 SST
12
174
95/ 25
160
7
2
1"-15
22
16090 SST
16
232
95/ 25
160
7
2
1"-15
22
12130 PVT
10
145
136/ 36
200
7
2
1"-15
17
12130 SST
12
174
136/ 36
200
7
2
1"-15
22
16130 SST
16
232
136/ 36
200
7
2
1"-15
22
07120 PVT
7
100
148/ 39
90
5
1
11/2 - 20*
18
1
07120 SST
7
100
148/ 39
90
5
1
1 /2 - 20*
26
07220 PVT
7
100
232/ 61
160
5
1
11/2 - 20*
18
1
07220 SST
7
100
232/ 61
160
5
1
1 /2 - 20*
26
04350 PVT
4
58
350/ 93
200
5
1
11/2 - 20*
18
04350 SST
4
58
350/ 93
200
5
1
1
1 /2 - 20*
26
All performance data applies to water at 20 °C.
The suction lift applies when the suction line and liquid end are full and correctly installed.
* Sigma types 07120, 07220 and 04350, the valves used in the liquid end are DN 25 (G11/2). Since DN 20 is usually adequate for
this tubing (see Technical Data, connection-suction/discharge side) the connector parts to be ordered by Identcode (e.g.
washers) have already been reduced to DN 20, i.e. tubing and accessories can be DN 20.
Materials in contact with chemicals
Material
version
Liquid end
Suction/
discharge
connector
Seals
Balls
Springs
Integrated
overload valve
PVT
PVDF
PVDF
PTFE
Ceramic / glass*
Hastelloy C
PDFE/Viton®
SST
Stainless steel
1.4571/1.4404
Stainless steel
1.4581
PTFE
Stainless steel
1.4404
Hastelloy C
Stainless steel/
Viton®
* for 07120, 07220 and 04350
Temperature specifications
Permissible storage temperature:
Permissible ambient temperature:
–10 to +50 °C
–10 to +40 °C
Temperature compatibility (medium temperature) of materials
Material:
Long-term at max.
backpressure:
Short-term, max. 15 min.
at max. 2 bar
PVT
65 °C
100 °C
SST
90 °C
120 °C
The specified temperatures (see above) can be exceeded temporarily, e.g. for sterilisation or
flushing with hot water.
Accuracy
Under constant conditions and in minimum stroke length of 30 % corresponding to following
notes, the reproducibility of the metered quantity is better than ±2 %.
All specifications refer to metered quantities with water at 20 °C and correct installation of the
metering pump.
Page 26
®
ProMinent
Dulcodes UV-Desinfektionsanlage
3.1.2
Technical data
Dimensions Sigma/ 2 (mm)
Connection
variations
456/441*
C
A
B
PVDF
ØG
Ø165
185/170*
PP/PVC/PTFE
SS
D/Dl
136
26.5
Ø 6.5
28
120
+7
120
F
79.5
222
Fig. 9
E/El
61_01-101_00_32-73
* Dimensions for S2Ba
Model
Connector
A
B
C
D
D1**
E
E1**
F
QG
FM 130 PVT
DN 15
265/250*
160
G1A
104
124
326/329*
346/349*
82
101
FM 130 SST
DN 15
265/250*
160
G1A
104
124
326/329*
346/349*
82
101
FM 350 PVT
DN 25
304/289*
237
G 1 1/2 A
115
135
337/340*
357/360*
84
148
FM 350 SST
DN 25
304/289*
237
G 1 1/2 A
115
135
337/340*
357/360*
84
148
FM 130 = Identcode type 16050,16090,16130
FM 350 = Identcode type 04350,07120,07220
* Dimensions for S2Ba
** Dimensions with diaphragm rupture sensor
3.1.3
Dimension sheet Sigma/ 2 with stroke adjustment motor
78
218
Anschlussvarianten
186
18
100
Fig. 10
61_01-101_00_39-73_2_HM
®
ProMinent
Page 27
Dulcodes UV-Desinfektionsanlage
Technical data
3.1.4
Motor data
Electrical Data
Motors:
Identcode characteristic
3 ph IP 55
230 V/400 V
50 Hz
0.25 kW
1.62/0.94 A
S
3 ph IP 55
230 V/400 V
60 Hz
0.25 kW
1.42/0.82 A
S
1 ph AC
230 V
50/60 Hz
0.18 kW
1.7/1.5 A
M
1 ph AC
115 V
60 Hz
0.18 kW
3.3 A
N
3 ph EXe or EXde
230 V/400 V
50 Hz
0.18 kW
1.1/0.7 A
L
3 ph EXe or EXde
230 V/400 V
60 Hz
0.18 kW
1.1/0.6 A
P
3 ph IP 55
230 V/400 V
50/60 Hz
0.37 kW
......
R Version with external fan
1 PH 230 v; 50/60 Hz and PTC
1 ph IP 55
230 V
50/60 Hz
0.37 kW
.....
V Three phase motor with integrated
speed changer, (see chapter 11)
For more details you can request the motor specification sheets. Custom motors and/or custom
motor flanges are available on request.
WARNING
• EX-pump only: Drive motors must be secured by an appropriate motor protection switch.
A motor protection approved for this application must be used for Ex“e”-motors.
(Protection against heating due to overload)
• EX-pump only: motors in EX-areas must be installed and checked by persons with
“recognised skills”!
• EX-pump only: observe the operating manual supplied with the EX motor!
Fuse data
IMPORTANT
• The motors are not fuse-protected. Fit a motor circuit breaker!
• When connecting the motor, make sure that it rotates in the correct direction (see Fig. 11).
direction
of rotation
Protection against accidental contact and moisture (IP)
Motor: IP 55 DIN EN 60034-5 (in accordance with DIN VDE 0470 Part 1, corresponds to
EN 60529 and IEC 529).
External fan
Notes on electrical connection of the motor, of the external fan in the case of variable speed
motors with external fan and the temperature monitor can be found in the “General Operating
Instructions Manual for ProMinent® Motor Driven Metering Pumps and Hydraulic Accessories”!
3.1.5
Fig. 11
Stroke actuator drive mechanism
230 V ± 10 % 50/60 Hz
11.7 W
115 V ± 10 %
11.7 W
60 Hz
Cf. “Appendix” for terminal connection diagram.
3.1.6
Stroke adjuster drive mechanism
230 V ± 10 % 50/60 Hz
6.5 W
115 V ± 10 %
6.5 W
60 Hz
Cf. “Appendix” for terminal connection diagram.
3.1.7
Electrical data, stroke sensor “Sigma”
a) Reed contact (Identcode characteristic “Stroke sensor”: 1)
Pin 1 (white)
=
4.5 V to 24 V, max. 10 mA
Pin 2 (brown)
=
OUT, open collector, 24 V, 20 mA
Pin 3 (green)
=
GND
Pulse width (low) ≥
4 ms (depending on gearbox and power frequency)
Page 28
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Technical data
b) Namur sensor, intrinsically (Identcode characteristic “Stroke sensor”: 3)
WARNING
• EX-pump only: intrinsically safe installations must be installed and checked by persons
with “recognised skills”!
• EX-pump only: observe documents supplied with the sensor!
Blue
-
Brown
+
5-25 V DC, Namur type and/or DIN 19234, zero volt design.
Rated voltage: 8 V DC (Ri ~ 1 kΩ)
Power consumption:
Active surface, uncovered > 3 mA
Active surface, covered < 1 mA
Rated switching distance: 1.5 mm
The monitor/feeder must be capable of evaluating current changes in order to indicate
diaphragm rupture!
3.1.8
Electrical data, pacing relay “Sigma”
Relay input
(power supply for the relay board)
Input voltage
Mains frequency
Power consumption
200/230 V AC (180-254 V)
50/60 Hz
10 mA (230 V/50 Hz)
100/115 V AC (90-134 V)
50/60 Hz
15 mA (115 V/60 Hz)
24 V DC (20-28 V)
-
10 mA at 24 V DC
Relay output
Voltage, max.
24 V DC
Current, max.
100 mA
Hook up duration
Standard
100 ms
adjustable
The contacts are zero volt.
3.1.9
Sound intensity level
The sound intensity level is < 70 dB (A)
at maximum stroke, maximum stroking rate, maximum back pressure (water) in accordance with
DIN EN 12639 (noise measurement in fluid pumps)
®
ProMinent
Page 29
Dulcodes UV-Desinfektionsanlage
Start-up/Maintenance
4
Start-up/Maintenance
WARNING
• For all metering pumps for metering inflammable media applies: Starting up and
emptying only supervised by a competent person.
IMPORTANT
Observe the safety notes provided in Section 1.
4.1
Start-up
All general guidelines in the accompanying ”General operating instructions ProMinent®
motordriven metering pumps and hydraulic accessories” apply.
Diaphragm pumps with mechanically actuated diaphragm: no additional measures necessary,
however, version with diaphragm rupture indicator, version Ex“i”*, must be used on principle.
For all metering pumps for metering inflammable media applies: starting up and emptying only
supervised by a competent person.
Inflammable media may only be lifted with stainless steel liquid ends. - For exceptional cases,
where this is not possible, also PTFE with carbon may be used, our versions TT_ are made of
conductive plastics. In this case, special attention must be paid by the user due to the lower
mechanical stability.
4.2
Maintenance
WARNING
• EX-pump only: Wear parts (diaphragms, bearings etc.) of metering pumps used in
potentially explosive atmospheres must be replaced after having completed 90% of their
nominal product life.
• The lubricant supply must be regularly checked for lubricated pumps, for instance by
checking the fill level, visual inspection for leakages etc.
• EX-pump only: check that the pressure relief valve downstream from the pump is
functioning correctly!
The pressure relief valve must prevent the gearbox from being overloaded and
overheating in explosion-threatened workplaces!
• The proper general function, in particular of the drive, must be safeguarded by regular
inspections (leakages, noises, temperatures, possible discoloration due to excess
temperatures....).
• Use original spare parts should exchange become necessary!
• EX-pump only: When cleaning plastic parts, attention must be paid to not generating any
electrostatic charge by rubbing excessively. - see danger sign.
• EX-pump only: metering pumps and their peripheral equipment must be serviced by
specially trained or authorised personnel!
IMPORTANT
After loosening the liquid end screws (e.g. to change the valves or diaphragm), the screws
must be retightened clockwise to the specified tightening torque.
What requires maintenance?
• Secure fit of liquid end screws.
• Secure fit of metering lines (intake and delivery sides).
• Secure fit of head valve and intake valve.
• Leakage hole at end disc for moisture (indicates possible diaphragm failure).
• Operate pump continuously for a short period of time in order to check whether it delivers
correctly.
Page 30
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Start-up/Maintenance
Maintenance intervals
General recommendation for maintenance intervals - every 3 months.
Shorter intervals are recommended if operated under load conditions (e.g. continuous operation).
The gear oil should be changed after approx. 5000 duty hours.
Gear oil ISO viscosity class VG 460, e.g. Mobil Gear 634,
ProMinent Order No. 555325 (Amount of oil approx. 0.5 l).
The metering diaphragm is a wearing part whose service life is dependent on following parameters:
• System backpressure.
• Operating temperature.
• Properties of medium to be metered.
The service life of the diaphragm is restricted in the case of abrasive media. In such cases, it is
recommended to check the diaphragm more frequently and to install a diaphragm failure monitor.
4.3
Replacement of wearing parts
Replacing diaphragm (see exploded diagrams in appendix!)
WARNING
• EX-pump only: metering pumps and their peripheral equipment must be serviced by
specially trained or authorised personnel!
• Always use original spare parts.
IMPORTANT
Flush liquid end first in the case of hazardous media. For this purpose, force water or a
suitable flushing agent through the intake connection of the liquid end with a wash bottle.
왘 Set stroke length to zero with the pump running. Switch off pump.
왘 Release the six screws holding the liquid end, detach liquid end together with screws.
왘 Release diaphragm from the push rod by jolting in counterclockwise direction and unscrew.
왘 Screw on new diaphragm until it is firmly seated on the push rod. Mount the dosing head with
screws such that the suction connection lies at the bottom (observe the flow through direction /
arrow marks on the valves). Switch on pump. Set stroke length to 100% and turn in screws
then tighten crosswise to 7.5 ± 0.5 Nm. Check pump for leaks at max. pressure.
®
ProMinent
Page 31
Dulcodes UV-Desinfektionsanlage
Start-up/Maintenance
NOTE
The tightening torque of the liquid end screws should be rechecked after 24 hours of
operation.
The tightening torques of the liquid end screws should be checked every 3 months for the
PVT material version.
Fig. 12
GUIDELINE ON VALVE INSTALLATION
In the case of suction problems during installation, place the valves on a firm surface and tap the
PTFE ball seat disk lightly with a brass rod and a hammer weighing about 300 g. Let the valves
such in the wet state.
approx. 300 g
Brass rod 9 mm diam. x approx. 200 mm
Fig. 13
NOTE
• If suction problems with the pump or leakage at the overcurrent valve are encountered,
first clean the ball and the ball seat disc.
• For media containing particles larger than 0.3 mm it is absolutely essential to install a
filter in the suction line.
Page 32
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Features of the S2Ca metering pumps
5
Features of the S2Ca metering pumps
5.1
Function description, motors
The pump has an integrated electronic overload cut-out in all versions. This responds as soon as
the maximum admissible power consumption is reached and stops the motor.
왘 If the motor stops due to a system overload the electronic controller detects the fault and
transmits a message which is displayed on the display panel and at the pump.
왘 The fault signal can be cancelled by pressing the ”P“ key, altering the level for a brief period at
the pause input (switch function) or by reconnecting the pump to the mains.
IMPORTANT
If the motor has been switched off via the electronic overload cut-out, check that the pump
is not continuously overloaded.
NOTE
• The motor is supplied pre-wired.
• The performance data in 3.1.1 are measured with the S2Ba (base model with 3-phase
motor). If the S2Ba has been fitted with a 1-phase motor there may be up to 5 % speed
reduction due to the different motor characteristic curve, i.e. corresponding 5 % reduced
feed rate.
• The controller changes over to digital stroking mode at low stroke frequencies! This takes
place at stroke frequencies below 1/3 of the maximum stroke frequency. This function is
designed to ensure sufficient cooling of the motor and low stroke frequencies.
Type: 100 – 230 V ± 10 %, 50/60 Hz
at 100 V
at 230 V
nominal output
250 W
250 W
nominal current
3.2 A
2.0 A
peak current (in operation)*
10 A
5.5 A
making peak current
12 A
24 A
fuse, internal**
4.0 AT (1.5kA)
4.0 AT (1.5kA)
* internal switching
** Only genuine ProMinent fuses, item no. 732414, may be used!
5.2
Operating modes
Function description, controller
Operating modes are selected using the MODE menu (depending upon identity code, some
operating modes may be absent).
“Analogue” operating mode: (Identity code, control variant: analogue)
The stroke rate is controlled via an analogue electrical signal via the “external control” terminal.
Signal processing is pre-selected at the controller.
“Manual” operating mode:
The stroke rate is controlled manually via the controller.
“Contact” operating mode:
This operating mode offers the opportunity to make fine adjustments with small increase/
decrease factors. Dosing can be activated by a pulse via the “external control” terminal or by a
semiconductor element. With the “pulse control” option it is possible to pre-set a feed quantity
(batch) or number of strokes (factor 0.01 to 99.99) via the control unit.
“Batch” operating function:
This operating mode offers the option of working with larger transfer factors (up to 65535).
Metering can be triggered by pressing the P key or a pulse from the “external control” terminal
via a contact or semiconductor element. A batching quantity or number of strokes can be preselected via the control unit.
®
ProMinent
Page 33
Features of the S2Ca metering pumps
Dulcodes UV-Desinfektionsanlage
“PROFIBUS®” mode: (Identity code, control variant: PROFIBUS®)
This operating mode provides the option of controlling the pump via the PROFIBUS® (see
“Supplementary instructions for ProMinent® gamma/ L and ProMinent® Sigma versions with
“PROFIBUS®”).
Functions
The following functions can be selected using the SET menu:
“Calibrate” function (Identcode, stroke length adjustment: manual + calibration):
The S3Ca can be operated in all operating modes including in calibrating mode. The
corresponding continuous displays can show the actual feed quantity or the feed rate.
Calibration is maintained within the stroke frequency range 0-180 strokes/ min. Calibration is
also maintained when a stroke frequency is altered up to ±10 % scale divisions.
“Auxiliary frequency” function:
It is possible to set a stroke rate in the SET menu, which may be activated via the “external
control” terminal. This auxiliary frequency overrides all other pre-set stroke rate frequencies.
“Flow” function:
Stops the S2Ca when the flow is insufficient. In the SET menu, the number of failed strokes is
entered after which the pump will be turned off.
The following functions are available as standard:
“Float switch” function:
Information on the liquid level in the feed chemical container is transmitted to the S2Ca. This
option requires the installation of a 2-stage float switch. This is connected to the “float switch”
terminal.
“Pause” function:
The S2Ca can be stopped by remote control via the “external control” terminal. The “pause”
function operates only via the “external control” terminal.
The following functions are activated by keystrokes:
“Stop” function:
The S2Ca can be stopped by pressing the STOP/START key without disconnecting from the
mains power supply.
“Prime” function:
Priming (short term feed at maximum frequency) is activated by pressing both arrow keys at
the same time (in “Stroke rate” permanent display).
Optional relay
The S2Ca has two connection options (not in PROFIBUS® version).
Optional “fault-indicating relay” or “power relay”:
In the event of fault signals, warning signals or float switch activation signals, connects an
electrical circuit to trigger alarm sirens etc. The relay is retrofitted via an aperture in the power
end.
“Fault indicating and pacing relay” option:
In addition to the fault indicating relay the pacing relay can make a contact with every stroke.
The relay is retrofitted via an aperture in the power end.
Function and error
indicators
The operating and error status is shown via the three LEDs and the “error” indicator on the
LCD (see also section 9):
LCD indicator
If a fault occurs “error” will appear along with an additional fault warning.
LED indicator
Operating indicator (green)
This indicator is lit as long as the S2Ca is operating correctly. It goes out briefly with every
stroke.
Warning indicator (yellow)
This warning light appears if the S2Ca electronics detect a situation that could lead to a fault,
e.g. “liquid levels low 1st stage”.
Error indicator (red)
This warning light appears if a fault occurs, e.g. “liquid levels low 2nd stage”.
Page 34
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Features of the S2Ca metering pumps
Hierarchy of operating modes, functions and fault statuses
The different operating modes, functions and fault statuses each have a differing effect on
whether and how the S2Ca functions. These effects are given below:
1.
Prime
2.
Fault, stop, pause
3.
Auxiliary frequency
4.
Manual, analogue, contact, batch
i.e.
1.
“Prime” can be activated in “Stroke rate” permanent display in any pump status
(as long as it is operable)
2.
“Fault”, “stop” and “pause” stop all system parts up to “prime”.
3.
The stroke rate of the “auxiliary frequency” always overrides the stroke rates of the operating
modes listed in point 4.
5.3
Sockets, symbols and wiring diagram
4
2
3
6
7
1
5
Fig. 14
(1) Socket for two-stage float switch with advance warning and de-activate function (with
function plug*, not illustrated)
(2) External socket for contact or analogue controller with zero volts deactivation via pause
function (with function plug* - not illustrated)
(3) Metering monitor socket for connection of ProMinent® metering monitor
(4) Mains switch (1-pin)
(5) Relay cable (fault indicating or pacing relay)
(6) Socket for diaphragm rupture sensor
(7) Mains lead with plug
*Must be plugged in unless cable attached.
®
ProMinent
Page 35
Dulcodes UV-Desinfektionsanlage
Features of the S2Ca metering pumps
Technical data, relay (control version)
2
Pump type S2Ca
3
1
4
Relay
Fault-indicating relay
Relay type
Fault-indicating relay
Voltage, max:
250 V 50/60 Hz
24 V DC
24 V 50/60 Hz
Current, max.
2 A (ohmic)
100 mA
100 mA
see Identcode
see Identcode
Hook up duration
Behaviour
1
4
3
2
Fault-indicating relay + pulse generator
pulse generator
Fault-indicating relay
100 ms
Service life
> 200 000 cycles*
Relay type
Power relay
Voltage, max.
250 V (50/60 Hz)
Current, max.
16 A (ohmic)
6
> 50 x 10 (10 V 10 mA)
see Identcode
> 200 000 cycles
yellow/NO
green/NC
fault indicating relay
white/NO
brown/C
pacing relay
Hook up duration
2
1
4
Behaviour
see Identcode
Service life
> 30 000 cycles*
green/NC
white/NO
* in the case of nominal load
brown/C
The contacts are zero volt.
N/C fault indicating relay - the relay closes immediately after the power is switched on and opens
in the event of a fault.
N/O fault indicating relay, the relay closes in the event of a fault.
Use suitable interference suppression (e.g. RC glands) when connecting inductive loads.
Page 36
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Features of the S2Ca metering pumps
Wiring diagram
View of cable connectors from front
Universal signal cable (5-score)
5 grey/auxiliary
4 black/ GND
1 brown / pause
Blue and black open
-> alarm signal
Brown and black open
-> alarm signal + pump stops
3 blue / analogue
for
3 brown pause
2 blue/alarm
1 black GND
for
2 white/cod
Float switch cable
Pause function:
brown and black closed
-> pump metering
Metering monitor cable
brown and black open
-> alarm + pump stopped
for
External/contact:
white and black closed
-> start contact for pump
(note pause function:
brown and black closed?)
blue, black
-> analogue output 0/4-20 mA
(note pause function:
brown and black closed?)
4 black/ GND
3 blue
2 white/cod
1 brown / 5 V
Analogue:
Auxiliary frequency:
grey and black closed
-> pump metering at pre-set stroking rate
Circuit examples see p. 40
Diaphragm rupture cable
External/contact cable (2 core)
Contact open -> alarm
-> pump stops with controller type 0
®
ProMinent
4 white
for
2 brown
1 black/GND
2 blue/alarm
for
Contact closed -> metering stroke
Page 37
Dulcodes UV-Desinfektionsanlage
Features of the S2Ca metering pumps
Technical data, external contact
Semi-conductor switch elements (e.g. transistors in open-collector circuits) or contactors (relays)
with a residual voltage of -0.7 V can be used as input switch elements.
Controller type 0 (see identity code)
Pin 1 = Pause input (activating function)
Voltage at open contacts: approx. 5 V
Input resistance: 10 kΩ
Controller:
– zero volts contact (approx. 0.5 mA)
– semi-conductor (residual voltage: < 0.7 V)
Pin 2 = Contact input
Voltage at open contacts: approx. 5 V
Input resistance: 10 kΩ
Controller:
– zero volts contact (approx. 0.5 mA)
– semi-conductor (residual voltage: < 0.7 V)
Min. contact duration: 20 ms
Max. pulse frequency: 25 pulses/s
Pin 3 = unused
Pin 4 = GND
Pin 5 = Auxiliary input
Voltage at open contacts: approx. 5 V
Input resistance: 10 kΩ
Controller:
– zero volts contact (approx. 0.5 mA)
– semi-conductor (residual voltage: < 0.7 V)
Controller type 1 (see identity code)
Pin 1 = Pause input (activating function)
Voltage at open contacts: approx. 5 V
Input resistance: 10 kΩ
Controller:
– zero volts contact (approx. 0.5 mA)
– semi-conductor (residual voltage: < 0.7 V)
Pin 2 = Contact input (not active during analogue operation)
Voltage at open contacts: approx. 5 V
Input resistance: 10 kΩ
Controller:
– zero volts contact (approx. 0.5 mA)
– semi-conductor (residual voltage: < 0.7 V)
Min. contact duration: 20 ms
Max. pulse frequency: 25 pulses/s
Pin 3 = Identical to input*
Input load:
approx. 120 Ω
Pin 4 = GND
Pin 5 = Auxiliary input
Voltage at open contacts: approx. 5 V
Input resistance: 10 kΩ
Controller: – zero volts contact (approx. 0.5 mA)
– semi-conductor (residual voltage: < 0.7 V)
* The metering pump makes its first metering stroke at approx. 0.4 mA (4.4 mA) and starts
continuous operation at approx. 19.2 mA.
Page 38
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Features of the S2Ca metering pumps
Block circuit diagram S2Ca
Inputs
Empty signal,
warning
Outputs
Pump, Inside
3 brown/pause
2 blue/alarm
Level
monitor
1 black/GND
Fault
indicating
relay
1 brown/5 V
2 white/cod
Metering
monitor
Flow control
3 blue
Metering
monitor
4 black/GND
Diaphragm
rupture
sensor
2 blue/alarm
1 black/GND
VDE cable:
2 green/NC
1 white /NO
4 brown/C
VDE cable:
1 yellow/NO (fault)
Fault
indicating
and
pacing relay
Diaphragm
rupture
sensor
4 green/C (fault)
3 white/NO (pacing)
2 brown/C (pacing)
3 blue/analogue
2 white/contact
Circuit
examples
overleaf
1 brown/pause
4 black/GND
External
activation
5 grey/auxiliary
GND
Mains
®
ProMinent
Page 39
Dulcodes UV-Desinfektionsanlage
Features of the S2Ca metering pumps
Circuit examples: universal signal cable
by customer
„External contact“ function
(ProMinent® external/contact cable)
two-core
Cable
Pump, inside
2 white/contact
4 brown/GND
External
activation
Pulse rate,
e.g. contact water meter
„External contact“ function
(ProMinent® universal signal cable)
five-core
3 blue/analogue
2 white/contact
1 brown/pause
4 black/GND
External
activation
5 grey/auxiliary
Pulse rate,
e.g. contact water meter
„Pause“ function
3 blue/analogue
2 white/contact
1 brown/pause
4 black/GND
External
activation
5 grey/auxiliary
Permanent contact,
e.g. from control room
„Auxiliary frequency“ function
3 blue/analogue
2 white/contact
1 brown/pause
4 black/GND
External
activation
5 grey/auxiliary
Permanent contact,
e.g. from control room
„External analogue“ function
3 blue/analogue
2 white/contact
0/4-20 mA
1 brown/pause
4 black/GND
External
activation
5 grey/auxiliary
Analogue signal,
e.g. from magnetic inductive
flow meter
Page 40
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Features of the S2Ca metering pumps
IMPORTANT
• The universal signal cable, the external/contact cable and the level monitor cable should
not be less than 1.20 m long, otherwise cable recognition will fail.
5.4
Retrofitting relays
(not in PROFIBUS® version)
Delivery range:
1
1
1
relay circuit set with 2 screw fasteners
relay cable set with socket
seal
Press-out relay opening
WARNING
Disconnect the S3Ca from the mains power supply and rinse liquid end before commencing
work (see section 10)!
IMPORTANT
When preparing the opening, ensure that the punch is not forced through the entire pump
base!
Pump circuits may become damaged.
왘
왘
왘
왘
Inserting the relay component 왘
왘
왘
왘
왘
왘
Place the S2Ca on a firm surface with the relay opening press-out section at the top (see
fig. 15)
Place a punch (dia. 8-15 mm) in the centre of the relay opening press-out section , and
strike briefly and sharply with a hammer (approx. 250 g)
If necessary clean up the edges of the opening
Remove the pressed out section from the S2Ca
Hold the relay component with your right hand gripping the left and right hand edges of
the relay cover, and tilt the front end slightly to the left (see fig. 16)
Push the relay component through the relay opening, holding the upper corner of the lower
edge against the guide rail on the pump base, until the contact of the relay component has
reached the controller contact. (test: can you still move the end of the circuit back and
forth?)
Gently push the relay component right into the opening
Screw the relay cover firmly onto the housing using the screws provided
Insert the relay cable plug seal into the relay cover and screw on the plug (see fig. 18)
The pump is generally programmed ex-factory to ”drop-out action alarm relay“ and – if
fitted – ”pull-up action clock pulse generator relay“. If a switching function is required, the
pump can be reprogrammed at the Heidelberg plant (not necessary by PROFIBUS®-version).
Fig. 15
®
ProMinent
Fig. 16
Page 41
Features of the S2Ca metering pumps / Control elements
Dulcodes UV-Desinfektionsanlage
Fig. 17
6
Fig. 18
Control elements
Please acquaint yourself with the S2Ca control elements with the help of the “control elements
and key functions” overview!
Indicators
The LCD display supports the operation and setting of the S2Ca with a range of indicators:
Stop Aux Pause Error
Mem
Calib
Flow
Set
The indicators are interpreted as follows:
Symbol for P key:
The S2Ca is in settings mode.
Close symbol:
In a continuous display: lock (if code has been set).
In settings mode: indicates access to code menu.
Stop:
The S2Ca has been stopped using the STOP/START key.
Aux:
The S2Ca is pumping at the auxiliary frequency. In AUX menu:
the S2Ca is in the AUX menu.
Pause:
The S2Ca has been stopped using the “pause” function
(external).
Error:
A fault has occurred and the pump has been stopped.
Mem:
An additional “memory” function has been set in the “contact”
and “batch” operating modes.
In CNTCT or BATCH menus (“mem” flashes): the memory
function can be set.
Calib:
The S2Ca is in the CALIB menu.
In a continuous display (“calib” flashes”): Deviation from the
stroking rate from the value at the time of the calibration by
more than 10 percent (e.g. in the case of a stroke length of 40%
when it has been set to less than 30% or more than 50%).
Flow:
The S2Ca is in the FLOW menu.
Set:
The S2Ca is in the SET menu.
Exclamation mark:
The number of strokes reached is above the maximum value
(99999) that can be shown in the LCD display.
NOTE
When calibrated, the S2Ca displays the feed rate and the feed capacity in l and/or in l/h or
in gal and/or g/h.
Page 42
®
ProMinent
Dulcodes UV-Desinfektionsanlage
7
Settings
Settings
NOTE
• Open out the fold-out page following the title page fully! There you will find the overviews
“control elements and key functions” and “operating settings diagram”.
• If no keys are pressed within a period of 1 minute, the S2Ca will return to a continuous
display.
Basic information for setting up the S2Ca
= Settings option
= flashes
Set
FHAII
P
3s
P
Set
F
P
P
3s
continuous
display
Confirm entries
Exit menu option
without confirming
Press the P key briefly;
you will automatically move to the next menu option or to a continuous display.
Press the P key for 3 s:
The entry is cancelled and you will return to a continuous display.
#"!
i
1x
#"!
P
#"!
i
2x
#"!
Incremental change
Iof a value
Press the i key 1x;
you can toggle between altering the digits of a value (“change individual digits” = standard) or
incremental alteration of a value (“change a figure”).
Change adjustable values
Press UP or DOWN arrow key;
The flashing digit or figure will start to increase or decrease incrementally.
Confirm adjustable values
For “change individual digits”: confirm each digit using the P key. When the last digit has been
confirmed you will automatically move to the next menu option or to a continuous display.
For “change a figure”; press the P key 1x; you will simultaneously move to the next menu option
or to a continuous display.
Correct wrongly set digits
®
ProMinent
Press the i key 2x;
you will go back to the first digit.
Page 43
Dulcodes UV-Desinfektionsanlage
Settings
7.1
Check adjustable values
Before setting up the S2Ca you can check the current settings of adjustable values:
Press the i key (“i” as in “info”) when the S2Ca is in continuous display mode (There is no P key
symbol in the LCD display).
Each time you press the i key you will see a different continuous display. The number of
continuous displays depends upon the identity code, the selected operating mode and the
connected accessories (see overview “continuous displays”).
7.2
Change to settings mode
If you hold down the P key for 2 seconds in any continuous display, the S2Ca will change to the
settings mode.
If CODE 1 is set, the code must be entered after pressing the P key.
The following menu options appear first in the settings mode (see also overview “operating/
settings diagram”):
• MODE menu
• CODE menu (optional)
• SET menu
• CLEAR window
In order to adapt the S2Ca to your process requirements you must:
1. Select the operating mode in the MODE menu.
2. If necessary enter the settings for this operating mode in the SET menu.
Exception: Timer and PROFIBUS®.
IMPORTANT
Note the diagram below!
1.
MODE
menu
CODE
menu
Continuous
display
2s
P
2.
SET
menu
CLEAR
window
7.3
Select operating mode (MODE menu)
The following operating modes are selected via the MODE menu (depending upon identity
code, some operating modes may be absent):
Page 44
•
Manual: for operation by hand
(Identity code, control variant: manual, standard option)
•
Analogue: for electronic control
(Identity code, control variant: analogue current)
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Settings
•
Contact: for contact operation
(Identity code, control variant: external 1:1 / external with pulse control)
•
Batch: for batch operation
(Identity code, control variant: external with pulse control)
Analog
- ANALOG
Manual
Analog Manual Contact Batch
- MANUAL
P
P
Contact
- CONTACT
Batch
7.4
- BATCH
Settings for operating mode (SET menu)
NOTE
First select the operating mode in the MODE menu!
Exceptions: Timer and PROFIBUS®.
In the SET menu you can adjust various settings depending upon the selected operating mode.
The following programmable function settings menus appear in all operating modes:
•
Calibrate (CALIB menu)
•
Auxiliary frequency (AUX menu)
•
Flow (FLOW menu, available only if flow monitor is connected)
See also section 7.5!
Further settings menus depend upon the selected operating mode.
7.4.1
Settings for “manual” operating mode
There are no other settings menus in the overall SET menu for the “manual” operating mode
apart from those described in 7.5.
7.4.2
Settings for “analogue” operating mode (ANALG menu)
In addition to those settings menus described in 7.5, there is an additional ANALG menu in the
overall SET menu for the “analogue” operating mode.
The stroke rate is controlled by an analogue electrical signal via the “external control” terminal.
You can select three signal-processing methods:
•
0 - 20 mA:
set
at 0 mA the S2Ca does not operate
at 20 mA the S2Ca operates at 180 strokes/min.
Between these two extremes the stroke rate is proportional to the electrical
signal.
P
Set
analg
P
Analog
Set
o 20
mA
P
Continuous
display
®
ProMinent
Page 45
Dulcodes UV-Desinfektionsanlage
Settings
•
4 - 20 mA: at 4 mA the S2Ca does not operate
at 20 mA the S2Ca operates at 180 strokes/min.
Between these two extremes the stroke rate is proportional to the electrical
signal.
For signals of below 3.8 mA a fault will be detected and the S2Ca will stop
(e.g. cable break).
•
Curve:
In the “curve” processing mode you can programme the S2Ca ratios.
There are 3 options available:
•
= straight line
•
= lower band
•
= upper band
set
P
Set
analg
i1o40
P
Analog
Set
f2120
mA
Freq.
P
f1o60
P
er on
Analog
Set
Analog
P
Set
Analog
Set
Analog
Set
P
curve
Analog
Set
Freq.
P
i2160
Analog
Set
mA
P
P
Continuous
display
Straight line:
The following symbol appears in the LCD display:
.
You can enter any stroke frequency ratio for the S2Ca in proportion to the electrical signal.
You must enter two points P1 (I1, F1) and P2 (I2, F2). F1 is the stroke rate at which the pump
should operate at current I1: the straight line and the ratio are fixed accordingly:
Fmax
P2
F2
P1
F1
0
I1
I2
20
I [mA]
Fig. 19
NOTE
Draw a diagram like the one above - with values for (I1, F1) and (I2, F2) - in order to set
the S2Ca to your required stroke rate!
Page 46
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Settings
Lower/upper band:
This processing mode allows you to control a pump via an electrical signal as shown in the
diagrams below.
Lower band
Upper band
e.g. Alkali pump
e.g. acid pump
Fmax
Fmax
P1
F1
P2
F2
P2
F2
P1
F1
0
I1
Fig. 20
I2
20
I [mA]
0
I1
I2
I [mA]
20
Fig. 21
Lower band:
The symbol
appears in the LCD display. The S2Ca will operate below I1 at F1.
Above I2, the S2Ca ceases to operate. Between I1 and I2 the stroke rate is between F1 and F2,
proportional to the signal current.
Upper band:
The signal
appears in the LCD display. The S2Ca will cease to operate below I1.
Above I2, the S2Ca will operate at F2. Between I1 and I2 the stroke rate between is F1 and F2,
proportional to the signal current.
The smallest processable difference between I1 and I2 is 4 mA.
Error processing
In the “ER” (error) menu option you can activate an error processing function for the “curve”
mode. An error message appears for signals below 3.8 mA and the S2Ca stops.
7.4.3
Settings for “contact” operating mode (CONTCT menu)
In addition to those settings menus described in 7.5, there is an additional CONTCT in the
overall SET menu for the “contact” operating mode.
The operating mode “contact” allows you to activate a single stroke or a series of strokes. The
strokes can be activated by a pulse or via the “external control” terminal. This operating mode
is intended to transfer input pulses into a reduction (fraction) or small increase in strokes.
IMPORTANT
The factor resets to “1” if you change to a different operating mode.tity cod
®
ProMinent
Page 47
Dulcodes UV-Desinfektionsanlage
Settings
In the “contact - identity code: external with external pulse control” you can enter the number
of pulses after which a stroke should be carried out. “Contact - identity code: external with
external pulse control” is intended for small dosing quantities.
set
P
Set
cntct
P
Mem
Set
on
Contact
P
Mem
Set
0120
Contact
P
Continuous
display
The number of strokes per pulse depends upon the factor, which you can enter. This allows
you to vary to a certain extent the input pulses by a factor of 1.01 to 99.99 and/or reduce by a
factor of 0.01 to 0.99:
“Number of strokes activated = factor x number of input pulses”
Examples
Factor
Increase
Reduction
Pulse (sequential)
1
1
Stroke number (sequential)
2
1
2
25
1
25
99.99
1
99.99
1.50
1
1.5 (1 / 2)
1.25
1
1.25 (1 / 1 / 1 / 2)
1
1
1
0.50
2
1
0.10
10
1
0.01
100
1
0.25
4
1
0.40
2.5 (3 / 2)
(1 / 1)
0.75
1.33 (2 / 1 / 1)
(1 / 1 / 1)
Explanation of increase
At a factor of 1
At a factor of 2
At a factor of 25
For every 1 pulse, 1 stroke is activated
For every 1 pulse, 2 strokes are activated
For every 1 pulse, 25 strokes are activated
Explanation of decrease
At a factor of 1
At a factor of 0.5
At a factor of 0.1
At a factor of 0.75
After 1 pulse, 1 stroke is activated
After 2 pulses, 1 stroke is activated
After 10 pulses, 1 stroke is activated
After 2 pulses, 1 stroke is activated,
then after 1 pulse, 1 stroke is activated,
then after 2 pulses, 1 stroke is activated etc.
Page 48
1
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Settings
NOTE
If a remainder occurs when the factor is processed, the S2Ca counts up the remainder
values. When the sum reaches or exceeds “1” the S2Ca will activate a stroke. This ensures
that the stroke number corresponds exactly to the factor throughout the dosing operation.
The number of input pulses which have not been processed are stored by the S2Ca in the
stroke memory. The stroke buffer is limited to the batch size when memory is not activated
(- with “Memory” at 65535 stokes). You can delete it by switching to a different operating
mode.
You can optimally adapt the S2Ca to the respective process, e.g. in connection with contact
water meters.
“Memory” extension function
The “memory” extension function can be optionally activated (“mem” appears in the LCD
display). When “Memory” is activated the S2Ca adds any strokes which could not be carried
out up to the maximum capacity of the stroke buffer – 65535 strokes. If this maximum capacity
is exceeded the pump will register a fault.
7.4.4
Settings for “batch” operating mode (BATCH menu)
In addition to those settings menus described in 7.5, there is an additional BATCH menu in the
overall SET menu for the “batch” operating mode.
set
P
Set
batch
P
Mem
Set
on
Batch
P
Mem
Set
15420
Batch
P
L
Continuous
display
The “batch” operating mode is a variant of the “contact” operating mode (see 7.4.3).
You can pre-select a stroke number (no breaks, whole numbers only from 1 to 65535) as well
as a feed quantity (batch). To switch between entries for “stroke number” and “feed quantity”
press the i key 1x in the corresponding menu option (see also overview “operating/settings
diagram”, fold-out page).
The “batch” operating mode is intended for large dosing quantities.
Metering can be actuated by pressing the P-key or via a pulse from the “external control
socket”.
The number of input pulses which have not been processed are stored by the S2Ca in the
stroke memory. The stroke buffer is limited to the batch size when memory is not activated
(- with “Memory” at 65535 stokes). You can delete it by switching to a different operating
mode.
“Memory” extension function
The “memory” extension function can be optionally activated (“mem” appears in the LCD
display). When “Memory” is activated the S2Ca adds any strokes which could not be carried
out up to the maximum capacity of the stroke buffer – 65535 strokes. If this maximum capacity
is exceeded the pump will register a fault.
®
ProMinent
Page 49
Dulcodes UV-Desinfektionsanlage
Settings
7.5
Settings for programmable functions (SET menu)
The following programmable function settings menus appear in all operating modes:
•
Calibrate (CALIB menu)
•
Auxiliary frequency (AUX menu)
•
Flow (FLOW menu, available only if flow monitor is connected)
7.5.1
Settings for “calibration” function (CALIB menu)
set
P
Set
cal ib
Calib
Set
200
P
Calib
Set
N
P
on
04232
P
P
Calib
Set
L
start
P
Calib
Set
Set
un it
L
P
Continuous
display
The S2Ca can also run in calibration mode. The corresponding continuous displays show the
current dosing quantities or the feed rate.
The calibration is retained in the event of a change of the set stroke length by up to ±10 scale
rates percent (if the stroke length is set to 40 % the range is 30 % to 50 %). If the stroke length
is changed by more than ±10 scale rates percent the yellow warning light lights up, the permanent display flashes and the flashing “Calib” indicator appears.
NOTE
• Do not go below 30 % stroke length (SEK type: 50 %).
This will significantly affect accuracy of calibration.
• Calibration becomes increasingly accurate the more strokes made by the S2Ca during
calibration (recommended: at least 200 strokes).
WARNING
If using a hazardous feed chemical, the following setting instructions ensure adequate
safety precautions are taken!
Calibration
왘
Insert the suction tube into a measuring cylinder containing the feed chemical - the
discharge tubing must also be correctly installed (operating pressure,…!)
왘
Suck up the feed chemical (press both arrow keys at the same time) when the suction tube
is empty
왘
Note the liquid level in the measuring cylinder and the stroke length
왘
Select the CALIB menu and go the first menu option using the P key
왘
Select “ON” using an arrow key and change to the next menu option using the P key
왘
To commence calibration, press the P key. The S2Ca starts to pump and displays the
number of strokes (“STOP” appears at regular intervals)
왘
After a sufficient number of strokes, stop the S2Ca with the P key
왘
Calculate the dosed quantity (difference between the original quantity and the quantity
remaining)
왘
Enter this quantity in the next menu option and then change to the following menu option
by pressing the P key.
왘
Select the unit (“L” or “gal”) in the “UNIT” menu with an arrow key and push the P-button.
The S2Ca is calibrated.
The corresponding continuous displays show the calibrated values.
The total stroke number and total litres are set during calibration to “0”.
The S2Ca is in the STOP status.
Page 50
®
ProMinent
Dulcodes UV-Desinfektionsanlage
7.5.2
Settings
Settings for “auxiliary frequency” function (AUX menu)
Aux
IAJ
P
Set
=KN
P
Set
&#
Freq.
P
Continuous
display
The programmable function “auxiliary frequency” allows switching to a different stroke
frequency, which can be set in the AUX menu. It can be activated via the “external control”
terminal. When the auxiliary frequency is activated, “aux” appears in the LCD display.
This auxiliary frequency overrides the current stroke frequency set for the selected operating
mode.
7.5.3
Settings for the “flow” function (FLOW menu)
set
P
Set
flow
P
Flow
Set
on
P
Flow
Set
008
P
Continuous
display
The flow menu only appears when a dosing monitor is connected to the “dosing monitor”
terminal. This dosing monitor registers each discharge stroke of the S2Ca at the discharge
connector and transmits it back to the S2Ca. If this response transmission is serially omitted
for a period set in the FLOW menu (due to failure or below-minimum dosing) the S2Ca stops.
7.6
Setting code (CODE menu)
The code menu is used to select whether you want to prevent access to parts of the settings
options.
code
P
code1
P
5432
P
Continuous
display
In the first menu option you can choose CODE 1 or CODE 2 (both use the same number).
•
Select CODE 1 to prevent access to the settings mode (➀ in the overview “operating/
settings diagram”, fold-out page). In the next menu option, enter the number you wish to
use as the code.
•
Select CODE 2 to prevent access to the settings options for directly alterable values in the
continuous displays (➁ in the overview “operating/settings diagram”, fold-out page). In the
next menu option, enter the number you wish to use as the code.
•
Select NONE to remove a pre-set security lock.
7.7
Cancel total stroke number or total litres (CLEAR window)
In the CLEAR window you can delete the stored total stroke number and simultaneously the
total litres (= set to “0”). You may then press the P key briefly to exit this window.
The values displayed are counted incrementally from the point of commissioning the pump, or
from the last delete action.
clear
N
P
L
Continuous
display
®
ProMinent
Page 51
Dulcodes UV-Desinfektionsanlage
Operating
8
Operating
This section describes all operating options available to you when the S2Ca is in continuous
display mode (no P key symbol in the LCD display).
WARNING
• For all metering pumps for metering inflammable media applies: Starting up and
emptying only supervised by a competent person.
NOTE
• Open out the fold-out page following the title page fully! There you will find the overviews
“control elements and key functions” and “operating/settings diagram”.
• Look at the overview “continuous displays”. This page shows you which displays are
available in which operating mode, and which values are directly alterable in the
corresponding continuous displays.
8.1
Set stroke length
Manual operation
Stroke length is continually adjustable within a range of 0-100 %. The recommended stroke
length range, which will practically guarantee technical reproducibility, is 30-100 % (SEK type:
50-100 %).
NOTE
At low stroking rates (less than 1/3 maximum stroking rate) the controller switches to
digital stroking mode. This ensures adequate cooling of the motor at low stroking rates.
The following operating options are available via the different keys (see also figure on the next
page):
Stop/Start S2Ca
Start batch
Load factory settings
Change to settings mode
Check adjustable values
Change directly
alterable values
To stop S2Ca: press STOP/START key.
To start S2Ca: press STOP/START key.
Press the P key briefly in “batch” operating mode.
Press the P key for 15 s to load factory calibration settings!
Current settings will be deleted.
When you press the P key for 2 s in any continuous display the S2Ca will change to settings
mode (see section 7).
If CODE 1 is set, the code must be entered after pressing the P key.
Each time you press the i key you will see a different continuous display. The number of
continuous displays depends upon the identity code, the selected operating mode and the
connected accessories.
To change a value (see below) directly in the corresponding continuous display, press one of
the arrow keys until “set” appears in the LCD display. The delay has been programmed in to
prevent inadvertent changing of values.
If CODE 2 has been set, this code must be entered after pressing the arrow key.
Directly alterable values are as follows:
Stroke rate
Feed rate
Factor
In “manual”, “contact” and “batch” operating modes:
The stroke rate can be altered in the “stroke rate” display.
In “manual” operating mode
The feed rate can be altered in the “feed rate” display.
The factor is the number of strokes activated by an external pulse or a press of the P key (in
“batch” mode only).
In “Batch” operating mode:
You can alter the factor from the “remaining strokes” display.
The S2Ca returns to the original continuous display a few seconds after the factor has been
reset.
Display program version
Page 52
Press the P key for 10 seconds to display the program version.
Example: “V1052” + “X1010”.
In the case of “LOAD3” release the key immediately!
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Batch size
Priming
Cancel error
Operating / Troubleshooting
In “batch” operating mode:
The batch size can by changed from the “batch size/remaining litres” display.
The S3Ca returns to the original continuous display a few seconds after the batch size has
been reset.
The “priming” function is activated by pressing both arrow keys at the same time (in “Stroke
rate” permanent display).
Error messages are cancelled by pressing the P key briefly.
Continuous
display
STOP
Stop/start pump
START
2
Change directly alterable values
Prime
P
P
i
P
Start batch (in "batch" operating mode only)
Cancel error
Check adjustable values
2s
1
1 = Security lock (CODE 1)
Settings
mode
8.2
2 = Security lock (CODE 2)
Remote control
Remote control of the S2Ca is possible via a control cable or PROFIBUS® (see Section 5.3 and
Chapter 7, ”Supplementary instructions for ProMinent® gamma/ L and ProMinent® Sigma
versions with PROFIBUS®“ as well as your documentation in the annex).
9
Troubleshooting
WARNING
• EX-pump only: metering pumps and their peripheral equipment must be serviced by
specially trained or authorised personnel!
• Always take suitable precautions when using hazardous chemicals!
• Ensure the equipment is de-pressurised before working on the pump!
Pump primes despite completed stroke action and no venting
Cause
Remedy
Crystalline deposits on the ball seat because valves have dried out.
왘
Remove the suction sleeve from the chemical supply container and rinse out the liquid end
thoroughly.
왘
If still unsuccessful, dismantle valves and clean.
Fluid is seeping from the top plate
Cause
Remedy
®
ProMinent
The liquid end is not sealed against the pump diaphragm.
왘
Tighten screws in the liquid end.
왘
If unsuccessful, replace the diaphragm (see section 4.3).
Page 53
Dulcodes UV-Desinfektionsanlage
Troubleshooting
Green LED indicator (operating display) is not lit
Cause
Remedy
Incorrect or no mains voltage.
왘
Use the recommended mains voltage as given in the voltage specification on the
nameplate.
Error Messages
Red LED display is lit, “Error” and “MINIM” flash in the display
Cause
Remedy
Fluid level in the chemical storage tank has reached “liquid level low, stage 2”.
왘
Fill the chemical supply container.
Red LED display is lit, “Error” and “ANALG” flash in the display
Cause
Remedy
S2Ca is in “analogue” operating mode, a fault routine has been programmed in the ANALG
menu and the operating current has fallen below 3.8 mA.
왘
Remedy low operating current.
왘
Switch fault routine “OFF” (see section 7.4.2.).
Red LED display is lit, “Error” and “CNTCT” flash in the display
Cause
Remedy
S2Ca is in “contact” or “batch” operating mode and the extended function “memory” has been
set.
In addition a very large factor has been entered, too many contacts have been input or the Pkey has been pressed too often, resulting in an overflow of the stroke memory.
왘
Press the P-key, saved data will be deleted.
왘
Change S2Ca set up.
Red LED display is lit, “Error” and “FLOW” flash in the display
Cause
Remedy
Cause
Remedy
Dosing monitor not properly connected.
왘
Connect dosing monitor properly.
왘
Press P-key.
Dosing monitor has reported more defective strokes than have been set in the FLOW menu.
왘
Press P-key.
왘
Investigate the cause and remedy.
Red LED is lit. “Error” appears in the display and “MOTOR” is flashing
Cause
Remedy
Cause
Remedy
Cause
Remedy
The motor is not operating accurately because the backpressure is too high.
왘
Reduce backpressure.
왘
Press the P key (reset key).
The motor is overheating.
왘
Check ambient temperature (max. 40 ºC).
왘
Allow motor to cool down.
왘
Press the P key (reset key).
Other motor fault.
왘
Call ProMinent.
왘
Press the P key (reset key).
Red LED is lit. “Error” appears in the display and “TEMPERATURE” is flashing
Cause
Remedy
Cause
Remedy
Page 54
The temperature in the pump housing is too high because the ambient temperature is too high.
왘
Reduce ambient temperature.
왘
Allow motor to cool down.
왘
Press the P key (reset key).
The temperature in the pump housing is too high because the pump is consuming too much power.
왘
Check installation, rectify if necessary.
왘
Allow motor to cool down.
왘
Press the P key (reset key).
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Troubleshooting / Decommissioning and disposal
Red LED display is lit, “Error” appears in the display and “FAN” is flashing
Cause
Remedy
Fault related to fan in pump housing.
왘
Check fan and replace if necessary.
왘
Press the P key (reset function).
Red LED display is lit, “Error” appears in the display and “SYSTEM” is flashing
Cause
Remedy
Controller fault.
왘
Disconnect the pump from the mains and reconnect.
If the error message continues, send the pump back to ProMinent.
Red LED lights up, “Error” appears in the display and “Menu” flashes.
Cause
Remedy
Stroke buffer full
왘
Rectify fault
왘
Press P key (Make a note of what effect this has on your process).
All other Errors
Please contact your ProMinent branch or representative!
Fault Signals
Yellow LED display is lit
Cause
Remedy
Liquid level in chemical storage tank has reached “liquid level low, stage 1”.
왘
Fill chemical storage tank.
Yellow LED Display is lit and “calib” flashes
Cause
Remedy
The pump is calibrated and the stroke length deviates by more than ±10 % from the value at
the time of calibration.
왘
Reset the stroke length or calibrate the pump again to the desired stroke length.
10
Decommissioning and disposal
Decommissioning
WARNING
• EX-pump only: metering pumps and their periphery must be maintained or
decommissioned by qualified or authorised personnel!
• For all metering pumps for metering inflammable media applies: Starting up and
emptying only supervised by a competent person.
• When decommissioning the pump, ensure that all dirt and chemicals are cleaned from
the housing and particularly the liquid end.
• Always take suitable precautions when using hazardous chemicals!
• Ensure that the equipment is de-pressurised!
왘
Disconnect the pump from the mains.
왘
Empty the liquid end by placing the pump on its head and allowing the chemical to drain
out.
왘
Rinse the liquid end with a suitable material, thoroughly rinse the liquid end after use with
hazardous materials!
If decommissioning is only temporary, maintain the correct storage conditions:
Storage temperature:
-10 to +50 °C
Air humidity:
< 92 % relative humidity
Disposal
WARNING
Spring under tension!
Take particular care when disassembling the pump as the return spring (Item 5, Chapter 2.2)
is under considerable mechanical tension!
IMPORTANT
Observe your locally applicable regulations (particularly with regard to electronic scrap and
gear oil)!
®
ProMinent
Page 55
Dulcodes UV-Desinfektionsanlage
Spare parts and accessories
11
Spare parts and accessories
CAUTION
The assembly and installation of ProMinent® metering pumps with other-make parts that
are not tested and recommended by ProMinent are not permitted and can lead to personal
injury and damage to property for which no liability shall be accepted!
Spare parts
You will find the order numbers for the wearing parts in the exploded view drawings in the
annex. If you require further parts, please order the “Spare parts list ProMinent® Sigma/ 2”.
Actuator for automatic stroke adjustment, setting time approx. 1 sec for 1% stroke length,
feedback potentiometer 1k Ohm enclosure rating IP 54.
Adjuster comprising actuator and incorporating servo controller for stroke length adjustment
via standard signal. Standard signal input 0/4-20 mA, corresponds to stroke length 0 – 100 %.
Manual to automatic mode switch, switch for stroke length adjustment in manual mode,
mechanical position display of 0/4-20 mA actual stroke length value output for remote display.
Variable speed motors with integrated speed changer (Identcode characteristic V)
Power supply 1 ph 230 V, 50/60 Hz, 0.37 kW
Optional external control via 0/4-20 mA
Speed controllers in metal casing (Identcode characteristic Z)
The speed controller kit comprises a speed changer and a 0.37 kW variable speed motor.
Float switches
2-stage, with 2 m connection cable
Alarm relays
For signalling faults
Alarm and pacing relays
For cyclic timing of other devices and for signalling faults.
Control cables
Universal control cable 5-core/2.5 and 10 m
External contact cable 2-core/2.5 and 10 m
Foot valves
With intake filter and non-return ball for connection at end of intake line.
Metering valves
With spring-loaded non-return ball for metering in open or closed systems and for mounting
the metering line.
Backpressure valves
For exact metering at low operating pressure or as overflow safety valve.
Accumulators
For pulsation damping in long metering lines.
Metering monitors
For monitoring metering operations. After an adjustable number of non-acknowledged metering
strokes, a fault is indicated and the metering pump shut down.
Intake assemblies
With foot valve and float switch for expendable packing drums or metering tanks.
Metering tanks
From 35 to 1000 l capacity with lockable screw cover and necessary accessories.
Manual/electric stirrers
For mixing and preparing metering solutions.
Page 56
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Motor data sheet
Motor Datenblatt / Motor data sheet / Fiche technique pour moteur
Bestell Nr.
order no. / no. de commande
1011036
Motor-Typ
motor type
type du moteur
AF 63/4C-7
Leistungsfaktor
power factor
facteur de puissance
0,66
Maschinenart
type of machine
désignation
3-Ph. Motor
Wirkungsgrad
efficiency
rendement
88 %
50 Hz
Schutzart
degree of protection
degré de protection
IP55
Bemessungsfrequenz
rated frequency
fréquence nominale
Bauform
mounting
construction
IMB5
Bemessungsdrehzahl
rated speed
vitesse nominale
Bemessungsleistung
rated output
puissance nominale
0,25 kW
ATB
Hersteller
producer / producteur
1370
Wärmeklasse
temperature class
class d’isolement
U/min
rpm
t/mn
F
Bemessungsspannung
rated voltage
tension nominale
/∆
400/230 V
Anzugsstrom
starting current
courant de démarrage
3,2
fach
fold
fois
Bemessungsstrom
rated current
courant nominale
0,94/1,62 A
Anzugsmoment
starting torque
couple de démarrge
2,1
fach
fold
fois
Kippmoment
pull-out torque
couple de décrochage
2,3
fach
fold
fois
Geprüft nach
tested in acc. with
contrôlé selon
PTB Nr.
DIN EN 60034
ohne EX-Schutz
without EX-protection
Umgebungstemperatur
ambient temperature
température ambiante
Schaltung
connection
branchement
Anmerkung
comments
observation
max. 40 °C
/∆
400/230 V
380-420/220-240 V (50 Hz)
ProMinent
Pumpentyp
S2Ca HM _ _ T _ _ _ _ U _ _ _ _ _ _
ProMinent Dosiertechnik GmbH · 69123 Heidelberg · Germany
Nr./No. MD - 1011036
Datum/Date 28.02.2002
Motor datasheets are available for further information.
Special motors and special motor flanges are possible on request.
®
ProMinent
Page 57
EC Declaration of Conformity
Dulcodes UV-Desinfektionsanlage
For pumps without Ex protection:
For pumps with Ex protection:
the EC conformity declaration for the pump for explosion-threatened workplaces is supplied with the pump.
The EC conformity declarations, the EC series prototype test reports and the operating manuals for the individual components
are also supplied with the pump.
Page 58
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Exploded diagrams of liquid ends
Delivery unit Sigma/ 2 350-DN 25 PVT for identity code types: S2Ba/S2Ca 04350, 07120, 07220
Delivery unit Sigma/ 2 130-DN 15 PVT for identity code types: S2Ba/S2Ca 12050, 12090, 12130
Valve assy DN 15/PVT* Order No. 792517
Valve spring *
Valve ball *
Diaphragm FM 120 Order No. 1010285
Ball seat *
Valve assy DN 15/PVT* Order No. 792517
Spare parts kit FM 350 PVT Order No. 740325
Spare parts kit FM 130 PVT Order No. 740324
* The listed items are constituent parts of the spare part kit.
** Special accessories (not included in spare part kit).
Subject to technical modifications.
®
ProMinent
Fig. 22
61_05-104_00_99-03
Page 59
Exploded diagrams of liquid ends
Dulcodes UV-Desinfektionsanlage
Delivery unit Sigma/ 2 350-DN 25 PVT for identity code types: S2Ba/S2Ca 04350, 07120, 07220
Delivery unit Sigma/ 2 130-DN 15 PVT for identity code types: S2Ba/S2Ca 12050, 12090, 12130
Overflow valve assy 12 bar PVA Order No. 1018572
Overflow valve assy 10 bar PVA Order No. 1018947
Overflow valve assy 7 bar PVA Order No. 740811
Overflow valve assy 4 bar PVA Order No. 740812
For other spare parts see delivery unit without overflow valve (see P. 56).
Subject to technical modifications.
Fig. 23
61_05-104_01_00-03
Delivery unit Sigma/ 2 350-DN 25 SST for identity code types: S2Ba/S2Ca 04350, 07120, 07220
Delivery unit Sigma/ 2 130-DN 15 SST for identity code types: S2Ba/S2Ca 12050, 12090, 12130, 16050, 16090, 16130
Overflow valve assy 16 bar SSA Order No. 1019246
Overflow valve assy 12 bar SSA Order No. 740813
Overflow valve assy 7 bar SSA Order No. 740815
Overflow valve assy 4 bar SSA Order No. 740814
For other spare parts see delivery unit without overflow valve (see P. 58).
Subject to technical modifications.
Page 60
Fig. 24
61_05-104_01_01-03_2
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Exploded diagrams of liquid ends
Delivery unit Sigma/ 2 350-DN 25 SST for identity code types: S2Ba/S2Ca 04350, 07120, 07220
Delivery unit Sigma/ 2 130-DN 15 SST for identity code types: S2Ba/S2Ca 12050, 12090, 12130
Spring **
Valve assy DN 10/SST* Order No. 809459
Ball *
Diaphragm FM 050 Order No 1010279
Diaphragm FM 065 Order No. 1010282
Ball seat *
Valve assy DN 10/SST* Order No. 809459
Spare parts kit FM 350 SST without valve
Spare parts kit FM 350 SST with 2 valves
Spare parts kit FM 130 SST without valve
Spare parts kit FM 130 SST with 2 valves
Order No. 740327
Order No. 740329
Order No. 740326
Order No. 740328
* The listed items are constituent parts of the spare parts kit.
** Special accessories (not included in spare parts kit).
Subject to technical modifications.
®
ProMinent
Fig. 25
61_05-104_01_01-03_2_norm
Page 61
Exploded diagrams of liquid ends
Dulcodes UV-Desinfektionsanlage
Retrofit kit double diaphragm S2Ba/S2Ca
S1Ba Retrofit kit double diaphragm FM 050 Order No. 1009846
S1Ba Retrofit kit double diaphragm FM 065 Order No. 1009848
S1Ba Retrofit kit double diaphragm FM 120 Order No. 1009850
S1Ca Retrofit kit double diaphragm FM 050 Order No. 1009847
S1Ca Retrofit kit double diaphragm FM 065 Order No. 1009849
S1Ca Retrofit kit double diaphragm FM 120 Order No. 1009851
Lense Order No. 792807
Diaphragm failure detector *
* These items belong to the retrofit kit.
Subject to technical modifications.
Page 62
Fig. 26
61_05-104_00_98-03_2
®
ProMinent
Dulcodes UV-Desinfektionsanlage
Wiring diagram
Stroke actuator wiring diagram
Feedback signal mA
Input signal mA
4 3 2 1
1 2 3
PE N L
Power supply
Wiring diagram for stroke length adjuster
Power supply
P2
P1
N
3
2
1
E
V+
5
Sig.
6
-
®
ProMinent
7
Page 63
Download PDF