Moxa Technologies | 5600 | Installation guide | Moxa Technologies 5600 Installation guide

NPort 5610/5630/5650 Series
Quick Installation Guide
Reset Button—Press the Reset button continuously for 5 sec to load
factory defaults: Use a pointed object to press the reset button. Release
the button after the Ready LED stops blinking.
LED Indicators on the Front Panel
The front panels of NPort 5600 have several LED indicators, as described
in the following table.
LED Name
Second Edition, July 2006
1. Overview
Welcome to the MOXA NPort 5600 Series. NPort 5610-16/8 has 16 or 8
RS-232 ports, NPort 5630-16/8 has 16 or 8 RS-422/485 ports, and NPort
5650-16/8 have 16 or 8 RS-232/422/485 ports.
Ready
2. Package Checklist
The NPort 5600 package should contain the following items:
y 1 16-port or 8-port serial device server
y NPort Documentation & Software CD
y NPort 5600 Quick Installation Guide
y Power cord (included with AC version of the product)
Optional Accessories
8-pin RJ45 to Male DB9 cable, 150 cm
y CBL-RJ45M9-150:
8-pin RJ45 to Female DB9 cable, 150 cm
y CBL-RJ45F9-150:
8-pin RJ45 to Male DB25 cable, 150 cm
y CBL-RJ45M25-150:
8-pin RJ45 to Female DB25 cable, 150 cm
y CBL-RJ45F25-150:
Notify your sales rep if any of the above items are missing or damaged.
3. Hardware Introduction
The NPort 5600 Series has 12 models: NPort 5610-16, NPort 5610-8,
NPort 5610-16-48V, NPort 5610-8-48V, NPort 5630-16, NPort 5630-8,
NPort 5650-8, NPort 5650-16, NPort 5650-8-M-SC,
NPort 5650-16-M-SC, NPort 5650-8-S-SC, and NPort 5650-16-S-SC.
The front and rear panels are shown below:
Front panel of NPort 5600 Series
5610-16
Rear panel of NPort 5610/5630/5650 (AC Power)
Serial ports
1
2
3
4
5
6
7
9
8
10
11
12
13
14
15
16
LAN
AC POWER 100-240V, 47-63Hz
Rear panel of NPort 5650 (Fiber Model)
Fiber
Serial ports
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
12
13
14
15
16
Link
AC POWER 100-240V, 47-63Hz
Rear panel of NPort 5610-16-48V (DC Power)
ON
V+ V-
Serial ports
OFF
1
2
3
4
5
6
7
8
9
10
11
LAN
P/N: 1802056000200
—1—
1-16
LED Color
LED Function
Off
Power is off, or power error condition exists.
Steady on: Power is on and NPort is
booting up.
Red
Blinking: Indicates an IP conflict, or that
DHCP or BOOTP server did
not respond properly.
Steady on: Power is on and NPort is
functioning normally.
Green
Blinking: The NPort has been located by
NPort Administrator’s
Location function.
Orange
Serial port is receiving data.
Green
Serial port is transmitting data.
No data is being transmitted or received
Off
through the serial port.
LCM Display Panel—If the NPort is working properly, the LCM panel
will be colored green. The red Ready LED will also light up, indicating
that the NPort is receiving power. After the red Ready LED turns green,
you will see a display similar to:
N
1
P
9
5
2
6
.
y NP5610-16
y 38
y 192.168.127.254
1
1
0
6
8
1
.
6
1
_
2
3
7
8
.
2
5
4
is the NPort’s name
is the NPort’s serial number
is the NPort’s IP address
LCM Panel Operation—There are four buttons on NPort 5600’s front
panel. These buttons are used to operate the server’s LCM panel. Going
from left to right, the buttons are:
Button Action
MENU Activates the main menu, or returns to an upper level.
Scrolls up through a list of items shown on the LCM panel’s
second line.
Scrolls down through a list of items shown on the LCM panel’s
second line.
SEL Selects the option listed on the LCM panel’s second line.
Detailed LCM Panel Operating instructions can be found on the
CD-ROM in the NPort 5600 Series User’s Manual.
Link Indicator on the Rear Panel of NPort 5650 Fiber Model
The rear panels of NPort 5600 have a link indicator, as described in the
following table.
—2—
LED Name LED Color
LED Function
Off
Fiber is disconnected
Fiber is connected and no data is being
Green
Link
transmitted
Fiber is connected and data is being
Blinking
transmitted
4. Hardware Installation Procedure
STEP 1: After removing NPort 5600 from the box, the first thing you
should do is attach the power adaptor.
STEP 2: Connecting the Power
AC: Connect the NPort 5610/5630/5650 100 to 240 VAC power cord to
the AC connector. If the power connection is correct, the “Ready”
LED will glow solid red until the system is ready, at which time the
“Ready” LED will change to green.
DC: Connect NPort 5610-16/8-48V’s power cord to the DC connector,
and then perform the following:
1. Loosen the screws on the V+ and V- terminals of
NPort 5610-16/8-48V’s terminal block.
ON
OFF 2. Connect the power cord’s 48 VDC or -48 VDC
wire to the terminal block’s V+ terminal, and the
power cord’s DC Power Ground wire to the
terminal block’s V- terminal, and then tighten the
V+ Vterminal block screws. (Note: NPort
5610-16/8-48V can still operate even if the
48V/-48V and DC Power Ground are reversed.)
If the power is connected properly, the “Ready” LED will glow a solid
red until the system is ready, at which time the “Ready” LED will change
to green.
Grounding NPort 5610-16/8-48V:
Grounding and wire routing help limit the effects
of noise due to electromagnetic interference
ON
OFF
(EMI). Run the ground connection from the
ground screw to the grounding surface prior to
connecting devices. The Shielded Ground
V+ V(sometimes called Protected Ground) contact is
the second contact from the right of the 5-pin
power terminal block connector located on the
SG
rear panel of NPort 5610-16/8-48V. Connect the
SG wire to the Earth ground.
STEP 3: Connect NPort 5600 to a network. Use a standard
straight-through Ethernet cable to connect to a Hub or Switch. When
setting up or testing NPort 5600, you might find it convenient to connect
directly to your computer’s Ethernet port. In this case, use a cross-over
Ethernet cable.
STEP 4: Connect NPort 5600’s serial port to a serial device.
Placement Options: You can place NPort 5600 on a desktop or other
horizontal surface.
—3—
5. Software Installation Information
To install NPort Administration Suite, insert the NPort Document &
Software CD into your computer’s CD-ROM drive. Once the NPort
Installation CD window opens, click the INSTALL UTILITY button,
and then follow the instructions on the screen.
To view detailed information about NPort Administration Suite, click
the DOCUMENTS button, and then select “NPort 5600 Series User’s
Manual” to open the pdf version of this user’s guide.
6. Pin Assignments and Cable Wiring
Serial Port Pinouts
for NPort 5610
RJ45 Port
DB9-M DB9-F DB25-M DB25-F Serial Port
Serial
Device
NPort 5630
TxD+
TxDRxDRxD+
GND
3
4
5
6
7
5
3
2
1
8
5
2
3
1
7
7
2
3
8
5
7
3
2
8
4
Serial Cables for NPort 5610/5650 (RS-232)
8
1
DB9-M DB9-F DB25-M DB25-F Serial Port
8
Serial
Device
NPort 5610
NPort 5650
Pin
RS-232
Pin
1
2
3
4
5
6
7
8
DSR (in)
RTS (out)
GND
TxD (out)
RxD (in)
DCD (in)
CTS (in)
DTR (out)
1
2
3
4
5
6
7
8
RS-422
4-wire RS-485
----TxD+
TxDRxDRxD+
GND
---
2-wire RS-485
--------DataData+
GND
---
RS-232
1
2
3
4
5
6
7
8
DSR
RTS
GND
TxD
RxD
DCD
CTS
DTR
RS-422
4-wire RS-485
--TxD+
GND
TxDRxD+
RxD-----
2-wire
RS-485
----GND
--Data+
Data-----
1
8
3
1
7
—4—
3
8
5
6
4
7
2
3
8
5
20
20
5
7
3
2
8
4
6
DTR
CTS
GND
RxD
TxD
DCD
RTS
DSR
DB9-M DB9-F DB25-M DB25-F Serial Port
Serial
Device
2
3
4
5
6
RJ45 Port
Serial
Device
2
1
8
4
8
5
2
3
1
7
6
7
5
3
2
1
8
5
2
3
1
4
7
2
3
8
5
7
3
2
8
RxD+
GND
RxDTxD+
TxD-
Serial Cables for NPort 5650 (2-wire RS-485)
DB9-M DB9-F DB25-M DB25-F Serial Port
5
6
7
6
7
5
3
2
1
8
4
NPort 5650
TxD+
GND
TxDRxD+
RxD-
NPort 5630
DataData+
GND
1
2
3
4
5
6
7
8
RJ45 Port
Serial Cables for NPort 5630 (2-wire RS-485)
RJ45 Port
DSR
RTS
GND
TxD
RxD
DCD
CTS
DTR
Serial Cables for NPort 5650 (RS-422/4-wire RS-485)
Serial Port Pinouts for NPort 5650
Pin
RxD+
RxDTxDTxD+
GND
Serial Port Pinouts for NPort 5630
RJ45 Port
1
7. Environmental Specifications
Serial Cables for NPort 5630 (RS-422/4-wire RS-485)
2
8
4
DataData+
GND
DB9-M DB9-F DB25-M DB25-F Serial Port
Serial
Device
NPort 5650
GND
Data+
Data-
3
5
6
5
2
1
5
3
1
7
3
8
7
2
8
GND
Data+
Data-
LAN
Ethernet
Protection
Optical Fiber
Distance
Min. TX Output
10/100 Mbps, RJ45
Built-in 1.5 KV magnetic isolation
Multi mode
Single mode
0 to 2 km, 1310 nm
(62.5/125 μm, 500
MHz*km)
-20 dBm
Max. TX Output
-14 dBm
0 to 40 km, 0 dBm
Sensitivity
-34 to -30 dBm
-36 to -32 dBm
Serial Interface
Interface
No. of Ports
Port Type
Signals (RS-232)
Signals (RS-422)
Signals (2-wire RS-485)
Signals (4-wire RS-485)
Serial Line Protection
RS-485 Data Direction
Power requirements
Power Input
Power Consumption
NPort 5610-8/16
NPort 5610-8/16-48V
NPort 5630-8/16
NPort 5650-8/16
NPort 5650-S-SC-8/16
NPort 5650-M-SC-8/16
Operating temp.
Operating humidity
Dimensions (W×D×H)
Serial line protection
Magnetic isolation
Power line protection
Regulatory approvals
RS-232/422/485
16/8
8-pin RJ45
TxD, RxD, RTS, CTS, DTR, DSR, DCD,
GND
Tx+, Tx-, Rx+, RxData+, Data-, GND
Tx+, Tx-, Rx+, Rx15 KV ESD for all signals
ADDC™ (Automatic Data Direction Control)
100 to 240 VAC, 47 to 63 Hz,
±48 VDC (38 to 72 VDC, -38 to -72 VDC)
141 mA @ 100 VAC, 93 mA @ 240 VAC
135 mA @ 48 VDC
152 mA @ 100 VAC, 98 mA @ 240 VAC
158 mA @ 100 VAC, 102 mA @ 240 VAC
164 mA @ 100 VAC, 110 mA @ 240 VAC
174 mA @ 100 VAC, 113 mA @ 240 VAC
0 to 55°C (32 to 131°F)
5 to 95% RH
190 × 44.5 × 478 mm (including ears)
190 × 44.5 × 440 mm (without ears)
15 KV ESD for all signals
1.5 KV for Ethernet
4 KV Burst (EFT), EN61000-4-4
2 KV Surge, EN61000-4-5
FCC Class A, CE Class A, UL, CUL, TÜV
Copyright © 2006
Moxa Technologies Co., Ltd.
All rights reserved.
Reproduction without permission is prohibited.
Tel: +886-2-8919-1230
Fax: +886-2-8919-1231
—5—
0 to 40 km, 1310 nm
(9/125 μm, 3.5 PS/
(nm*km))
0 to 40 km, -5 dBm
www.moxa.com
support@moxa.com.tw
—6—
Download PDF