Samsung | DC68-03144B-01 | Owner`s manual | Samsung DC68-03144B-01 Owner`s manual

Samsung SilverCare™
Washer Owner’s Manual
Register your product at
www.samsung.com/global/register
Code No.: DC68–02291A–08_EN
Features
1.SilverCare™ Sanitization
The winning combination! Samsung’s silver nano technology combines the sanitizing effect of silver
with state-of-the-art science for the ultimate in clean. Two plates of 99.9% pure silver are converted
into silver ions through electrolysis. Even in cold, bleach-less water, the silver particles remove 99.9% of
odorcausing bacteria for a “super clean” wash. So washing in cold water is energy efficient and better for
your clothes.
2. Extra Large Capacity
Even bulky garments and blankets get super clean. The large 3.79 cu.ft. capacity leaves enough room for
a more thorough, cleaner wash.
3. High Efficiency Energy & Water Saving
Washing with Samsung’s SilverCare™, even in cold water, sanitizes the laundry thereby saves 92% energy
used when compared to that with hot water sanitization.
4. Direct Drive Inverter Motor
The power to handle anything! Our direct-drive inverter motor delivers power right to the washer tub
from a variable speed, reversible motor.
A beltless direct-drive motor generates a higher spin speed of 1,200rpms for more effective, quiet
operation. The washer also has fewer moving parts, meaning fewer repairs.
5. Woolmark Certified
The machine wash wool cycle on the Samsung SilverCare™ machines has been tested and passed the
required Woolmark Company specification for machine washable wool products. Fabrics should be
washed according to the instructions on the garment label as specified by Woolmark and Samsung.
Pedestal with Storage Drawers An optional 15” pedestal is available to raise the washer for easier loading
and unloading. It also offers a built-in storage drawer that can hold a 100 oz.
bottle of detergent.
6. Stacking
Washer and dryer can be stacked to maximize usable space.
Safety Precautions
Congratulations on your new Samsung SilverCare™ Washer. This manual contains important information
on the installation, use, and care of your appliance. Please take time to read this manual to take full
advantage of your Washer’s many benefits and features.
What you need to know about Safety Instructions
Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur.
It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating your Washer.
IMPORTANT SAFETY SYMBOLS, WORDS, LABELS
WARNING – Hazards or unsafe practices that COULD result in severe personal injury or death.
CAUTION –
Hazards or unsafe practices that COULD result in minor personal injury or property damage.
WARNING – To reduce the risk of fire, explosion, electric shock, or personal injury when
using your Washer, follow the basic safety precautions below:
1. Read all instructions before using the appliance.
2. As with any equipment using electricity and moving parts, potential hazards exist. To safely
operate this appliance, become familiar with its operation and exercise care when using it.
3. Install and store your Washer away from weather exposure.
4. Install and level your Washer on a floor that can support its weight.
5. Your Washer must be properly grounded. Never plug it into an ungrounded outlet. See page A2 for details.
6. To avoid the possibility of fire or explosion:
• Do not wash items that have been washed, soaked, or treated with gasoline, dry cleaning solvents, or other
flammable or explosive substances. They give off vapors that could ignite or explode. Any material that has been
exposed to cleaning solvent or other flammable liquids or solids should not be placed in your Washer until all
traces of such liquids, solids, and fumes have been removed. Offending items include acetone, denatured alcohol,
gasoline, kerosene, certain liquid household cleaners and spot removers, turpentine, waxes, and wax removers
• Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash water.
They give off vapors that could ignite or explode.
• Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two
weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for two weeks or more,
turn on all hot water faucets and let the water flow for several minutes before using your Washer. This will release
any hydrogen gas build–up. Since the gas is flammable, do not smoke or use open flame during this time.
7. Unplug power cord before attempting to service your Washer.
8. Do not reach into the appliance when the tumbler is moving.
9. Do not let children play on or in your Washer. Close supervision is a must when children are near the Washer.
10. Do not tamper with controls.
11. Do not repair, replace, or service any part of your Washer unless you fully understand the recommended
user–repair instructions and have the skills to carry them out.
12. Store laundry aids and other material in a cool, dry place out of children’s reach.
13. Do not wash or dry items that are soiled with vegetable or cooking oil. These items may contain some oil after
laundering. Due to the remaining oil, the fabric may smoke or catch fire by itself.
14. Do not use chlorine bleach, ammonia, or acids (such as vinegar or rust remover) in the same wash. Hazardous fumes can form.
15. Do not machine wash fiberglass materials. Small particles can stick to fabrics washed in following loads and cause
skin irritation.
16. Before your Washer is removed from service or discarded, remove the door to the washing compartment to
avoid the danger of children or small animals getting trapped inside.
17. Do not sit on top of your Washer.
18. Inlet hoses are subject to damage and deterioration over time. Check the hoses periodically for bulges, kinks,
cuts, wear or leaks, and replace them every five years.
19. Ensure pockets are free from small irregularly shaped hard objects, foreign material, etc. ie. coins, knives, pins,
etc. These objects could damage your washer.
20. Do not wash clothing with large buckles, buttons, or other heavy metal.
SAMSUNG Clothes Washer
SAVEOwner’s
THESE INSTRUCTIONS
Instructions 1
Table of Contents
Installing Your Washer . . . . . . . . . . . . . . . . .
UNPACKING YOUR WASHER . . . . . . . . . . . . .
OVERVIEW OF YOUR WASHER. . . . . . . . . . . .
GROUNDING . . . . . . . . . . . . . . . . . . . . . . .
WATER . . . . . . . . . . . . . . . . . . . . . . . . . . .
DRAIN FACILITY . . . . . . . . . . . . . . . . . . . . .
FLOORING . . . . . . . . . . . . . . . . . . . . . . . . .
LOCATION CONSIDERATIONS . . . . . . . . . . . .
ALCOVE OR CLOSET INSTALLATION. . . . . . . .
IMPORTANT TO INSTALLER. . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
................
.................
.................
.................
.................
.................
.................
.................
.................
.................
.
.
.
.
.
.
.
.
.
.
............
.............
.............
.............
.............
.............
.............
.............
.............
.............
A-1
A-1
A-1
A-2
A-2
A-3
A-3
A-3
A-3
A-4
Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
LOADING YOUR WASHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2
Washing a Load of Laundry . . . . . . . . . . . . .
OVERVIEW OF THE CONTROL PANEL . . . . . . .
CHILD LOCK. . . . . . . . . . . . . . . . . . . . . . . .
GARMENT +. . . . . . . . . . . . . . . . . . . . . . . .
MY CYCLE . . . . . . . . . . . . . . . . . . . . . . . . .
FOR SILVERCARE™ WASHING (select models) .
DETERGENT USE. . . . . . . . . . . . . . . . . . . . .
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
................
.................
.................
.................
.................
.................
.................
.................
.
.
.
.
.
.
.
.
. . . . . . . . . . . . .C-1
. . . . . . . . . . . . . .C-1
. . . . . . . . . . . . . .C-4
. . . . . . . . . . . . . .C-4
. . . . . . . . . . . . . .C-4
. . . . . . . . . . . . . .C-5
. . . . . . . . . . . . . .C-6
. . . . . . . . . . . . . .C-6
Maintaining Your Washer . . . . . . . . . . . . . . .
CLEANING THE INTERIOR . . . . . . . . . . . . . . .
CLEANING THE DISPENSERS. . . . . . . . . . . . .
STORING YOUR WASHER . . . . . . . . . . . . . . .
.
.
.
.
................
.................
.................
.................
.
.
.
.
............
.............
.............
.............
D-1
D-1
D-1
D-1
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E-1
CHECK THESE POINTS IF YOUR WASHER.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E-1
INFORMATION CODES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E-3
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . .
FABRIC CARE CHART . . . . . . . . . . . . . . . . . .
HELPING THE ENVIRONMENT . . . . . . . . . . . .
DECLARATION OF CONFORMITY . . . . . . . . .
SPECIFICATION. . . . . . . . . . . . . . . . . . . . . .
CYCLE CHART . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
................
.................
.................
.................
.................
.................
.
.
.
.
.
.
. . . . . . . . . . . . .F-1
. . . . . . . . . . . . . .F-1
. . . . . . . . . . . . . .F-2
. . . . . . . . . . . . . .F-2
. . . . . . . . . . . . . .F-2
. . . . . . . . . . . . . .F-3
32
Installing Your Washer
UNPACKING YOUR WASHER
Unpack your Washer and inspect it for shipping damage. Make sure you have received all of the items
shown below.
If your Washer was damaged during shipping, or you do not have all of the items, contact 1-800SAMSUNG.
OVERVIEW OF YOUR WASHER
Hot water supply hose
Cold water supply hose
Detergent drawer
Control panel
Door
Drain Hose
Adjustable leg
Spanner
Bolt hole covers
Water Supply Hose
Hose guide
SAMSUNG Clothes Washer Owner’s Instructions A-1
Installing Your Washer
BASIC LOCATION REQUIREMENTS:
ELECTRICAL
• 120 Volt 60 Hz 15 AMP fuse or circuit breaker
• Individual branch circuit serving only your Washer is recommended.
• Your Washer is equipped with a power cord.
NEVER USE AN EXTENSION CORD.
GROUNDING
ELECTRICAL GROUNDING IS REQUIRED ON THIS APPLIANCE.
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least resistance for electric current.
This appliance is equipped with a power cord having a three-prong grounding plug for use in a properly
installed and grounded outlet.
WARNING - Improper connection of the equipment-grounding conductor can result in a
risk of electrical shock. Check with a qualified electrician or serviceman if you
are in doubt as to whether the appliance is properly grounded. Do not modify
the plug provided with the appliance – if it does not fit the outlet, have a proper
outlet installed by a qualified electrician.
IMPORTANT SAFETY PRECAUTIONS
•
To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and grounding
must be done in accordance with the National Electrical Code ANSI/FNPA, No. 70 Latest Revision
and local codes and ordinances. It is the personal responsibility of the appliance owner to provide
adequate electrical service for this appliance.
NEVER CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR
HOT WATER PIPES.
WATER
To correctly fill your Washer in the proper amount of time, water pressure of 20 – 120 psi is required.
Water pressure less than 20 psi may cause water valve failure, not allowing the water valve to shut off
completely. Or it may extend the fill time beyond what your Washer controls allow, resulting in your
Washer turning off. A time limit is built into the controls in the event of an internal hose becoming loose
and flooding your home.
The water faucets must be within 4 feet/122cm of the back of your Washer for the inlet hoses provided
with your Washer.
NOTE: Accessory inlet hoses are available in various lengths up to 10 feet/305cm for faucets that are
further away from the back of your Washer.
To avoid the possibility of water damage:
• Have water faucets easily accessible
• Turn off faucets when Washer is not in use.
• Periodically check there is no leakage at water inlet hose fittings.
WARNING - CHECK ALL CONNECTIONS AT THE WATER VALVE AND FAUCET FOR LEAKS.
A-2 SAMSUNG Clothes Washer Owner’s Instructions
Installing Your Washer
DRAIN FACILITY
The recommended height of the standpipe is 18 in/46 cm. The drain hose must be routed through the
drain hose clip to the standpipe. Standpipe must be large enough to accept the outside diameter of the
drain hose. The drain hose is attached at the factory.
FLOORING
For best performance, your Washer must be installed on a solidly constructed floor. Wood floors may
need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting and soft tile
surfaces are contributing factors in vibration and/or tendency for your Washer to move slightly during
the spin cycle.
Never install your Washer on a platform or weakly supported structure.
LOCATION CONSIDERATIONS
Do not install your Washer in areas where water may freeze, since your Washer will always maintain
some water in its water valve, pump, and hose areas. This can cause damage to belts, pump, hoses and
other components. Operating temperature should be above 60°F/16°C.
ALCOVE OR CLOSET INSTALLATION
MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:
Sides – 1 in / 25 mm
Top – 17 in / 432 mm
Rear – 2.375 in / 60 mm
Closet Front – 2 in / 51 mm
If both Washer and Dryer are installed together, the closet front must have at least 72 in2 or 465 cm2 of an
unobstructed air opening. Your Washer alone does not require a specific air opening.
SAMSUNG Clothes Washer Owner’s Instructions A-3
Installing Your Washer
IMPORTANT TO INSTALLER
Please read the following instructions carefully before installing your Washer.
These instructions should be retained for future reference
STEP 1
Removing the Shipping Bolts
Before using your Washer, you must remove the four shipping
bolts from the back of the unit.
1. Loosen all bolts with the supplied spanner.
2. Slide the bolt and spacer up and remove the bolt with
spacer through the hole in the rear wall of your Washer.
Repeat for each bolt.
3. Fill the holes with the supplied plastic covers.
4. Keep the shipping bolts and spacers for future use.
STEP 2
Selecting a Location
Before you install your Washer, make sure the location:
• Has a hard, level surface
• Is away from direct sunlight
• Has adequate ventilation
• Will not be freezing (below 32°F or 0°C)
• Is away from heat sources such as oil or gas
• Has enough space so that your Washer need not stand on its power cord
• Doesn’t have any carpeting that will obstruct ventilation openings.
STEP 3
Installing your Washer
1. Place the drain hose in the drain facility. Be sure an airtight
connection is NOT made between the drain hose and the
standpipe.
Standpipe must be at least 18 in or 46 cm high.
NOTE: Caution must always be exercised to avoid collapsing
or damaging the drain hose. For best results, the drain
hose should not be restricted in any way – by elbows,
couplings, or excessive lengths. For situations where the
drain hose cannot be conveniently elevated to at least 18
in or 46 cm, the drain hose must be supported.
2. Check the inlet hose to ensure a washer is inside each fill hose.
Thread the inlet hoses to the HOT and COLD faucet connections.
On the other end of the hose, check for one rubber washer per
hose and install each fill hose to the water valve. Make sure the
hose with the red line is attached to the HOT faucet. Tighten by
hand until snug, then two-thirds of a turn with pliers.
NOTE: For correct water use, connect both HOT and COLD
water valves. If one is not connected, “nF” (no fill) error
can occur.
A-4 SAMSUNG Clothes Washer Owner’s Instructions
LAUNDRY TUB
STAND PIPE
96” MAX.
18” MIN.
HOSE
RETAINER
TIE
STRAP
96” MAX.
18” MIN.
Installing Your Washer
3. Turn on “HOT” and “COLD “water supply and check all connections at
the water valve and the faucet for leaks.
4. Plug power cord into a 3-Prong, well grounded 120 volt 60 Hz
approved electrical outlet protected by a 15-amp fuse or comparable
circuit breaker.
Your Washer is grounded through the third prong of the power cord
when plugged into a three-prong grounded receptacle.
5. Slide your Washer into position.
6. Level your Washer by turning the leveling legs in or out as necessary by hand or wrench included
with your Washer.
When your Washer is level, tighten the nuts using the wrench or (-)driver.
NOTE: Your Washer must be leveled
on all four sides. A carpenter’s
level should be used on all
four corners of your Washer.
It’s a good idea after the first
dozen washes to recheck your
Washer’s levelness.
7. If you install your washer on softfloor,
you should place the rubber cup under
adjustable leg. Before put rubber cup,
please remove film for double-side tape
attached on rubber cup.
NOTE: If washer is installed on riser,
you should put rubber cup
under leg for riser.
SAMSUNG Clothes Washer Owner’s Instructions A-5
Operating Instructions
LOADING YOUR WASHER
•
You can fill the tub with dry, unfolded clothes; but DO NOT OVERLOAD the tub.
•
Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or
wrinkling of the load.
•
Wash delicate items such as bras, hosiery, and other lingerie in the Delicates/Hand Wash cycle with
similar lightweight items.
•
When washing big bulky items or a few smaller items that don’t fill the tub completely – a rug, a
pillow, stuffed toys, or one or two sweaters, for example – add a few towels to improve tumbling
and spin performance.
•
When washing heavily soiled loads, not overloading your Washer is very important to assure good
cleaning results.
•
To add a forgotten item:
1) Press the Cycle Selector dial
2) Wait for the Door Lock light to go out (5 seconds)
3) Add the item, close the door, and press the Cycle Selector dial.
After a pause of 10 seconds, the cycle will resume.
NOTE: To ensure thorough cleaning, add items within five minutes of starting the wash cycle.
Try washing Bedding, Towels, undergarments, and other articles that usually have close body
contact using the SilverCare™ Option, which Sanitizes using Cold Water.
B-1 SAMSUNG Clothes Washer Owner’s Instructions
Operating Instructions
GETTING STARTED
1. Load your Washer.
2. Close the door.
3. Add detergent and additives to the dispenser (see pages C6~C7).
4. Select the appropriate cycle and options for the load (see pages C2~C5).
5. Press the Cycle Selector dial.
6. The Wash Indicator light will illuminate.
7. The estimated cycle time will appear in the display.
The time may fluctuate to better indicate the time remaining in the cycle.
8. Before your Washer starts to fill, it will make a series of clicking noises to check the door lock and do
a quick drain.
NOTES:
• When the cycle is complete, the Door Lock light will go out and “End” will appear in the display.
• DO NOT attempt to open the door until the Door Lock light is off. To add a forgotten item, see
“Loading your Washer” section.
• When your Washer is restarted after a pause, expect a delay of up to 15 seconds before the
cycle continues.
• Pressing Power cancels the cycle and stops your Washer.
• The Pre Wash (select models), Wash, Rinse and Spin indicator lights will illuminate during those
portions of the cycle.
SAMSUNG Clothes Washer Owner’s Instructions B-2
Washing a Load of Laundry
OVERVIEW OF THE CONTROL PANEL
C-1 SAMSUNG Clothes Washer Owner’s Instructions
Washing a Load of Laundry
1.
Digital graphic display
2.
Temperature selection button
3.
Spin selection button
4.
Soil Level selection button
5.
Signal selection button
6.
SilverCare™ button
Displays the remaining cycle time, all cycle information, and error messages.
Press the button repeatedly to cycle through the different water temperature options.
Extra Hot/Cold - Heavily soiled, colorfast items. Only available with the Sanitize cycle.
Hot/Cold - Whites and heavily soiled, colorfast items.
Warm/Warm - Colorfast items. When warm rinse is selected, only the final rinse will be warm. The
other rinses will be cold to conserve energy.
Warm/Cold - Moderately soiled, colorfast items; most wrinkle-free items.
Cold/Cold - Brightly colored, very lightly soiled items; washable woolens.
Press the button repeatedly to cycle through the different spin speed options.
Extra High - Removes more water from loads during spin.
NOTE: To minimize wrinkling of wrinkle-free and no-iron fabrics, DO NOT use the Extra High spin
option for these loads, nor overload your Washer.
High - Use for underwear, t-shirts, jeans and sturdy cottons.
Medium - Use for jeans, wrinkle-free or wash-and-wear items and synthetics.
Low - Use for delicate items needing a slow spin speed.
No Spin - Drains your Washer without spinning. Use for extremely delicate items that cannot
tolerate any spin.
Press the button to select the Soil Level/washing time.
Heavy - For heavily soiled loads.
Normal - For moderately soiled loads. This setting is best for most loads.
Light - For lightly soiled loads.
Press the button to increase or decrease the end of cycle signal volume or turn off the signal.
Press this button to sanitize your laundry in cold water.
Active silver ions are produced from pure silver plates by the process of electrolysis and released
into the wash water effectively sanitizing your wash, even in cold water, without bleach. The
SilverCare™ system sanitizes with 92% less energy use than a traditional heat sanitization.
SAMSUNG Clothes Washer Owner’s Instructions C-2
Washing a Load of Laundry
7.
Select Cycle Option
Delay Start - Any cycle can be delayed for up to 12, 19 or 24 hours (select models) in one-hour
increments. Displayed hour indicates the time at which the wash will be finished.
Extra Wash - Add additional time to the wash for better stain removal.
Extra Rinse - Add an additional rinse at the end of the cycle to more thoroughly remove laundry
additives and perfumes.
Extra Spin - Add additional time to remove more water from loads
My Cycle - Choose your favorite cycle including temperature, spin, soil level, option, etc.
Pre Wash - To use this feature add detergent to the Pre Wash selection of the detergent
compartment. When turned on, the washer fills with cold water and detergent, tumbles, then
drains and advances to the selected wash cycle. Some cycles cannot be selected with this option.*
* You cannot select PreWash option in the Delicate/Hand Wash, Wool, Quick Wash and Active
Wear cycles.
8.
Cycle Selector
Select the appropriate cycle for the type of load.
This will determine the tumble pattern and spin speed for the cycle.
NOTE: To minimize wrinkling of laundry, select the Perm Press cycle.
Heavy Duty - For sturdy, colorfast fabrics and heavily soiled garments.
Normal - For most fabrics including cottons, linens, and normally soiled garments.
Whites - For white fabrics with or without bleach.
Perm Press - For wash-and-wear, synthetic fabrics, and lightly to normally soiled garments.
Delicates/Hand Wash - For sheer fabrics, bras, lingerie silk, and other handwash-only fabrics. For
best results, use liquid detergent.
Wool - For machine-washable wool. Loads should be under 8 pounds.
The wool wash cycle of this machine has been approved by Woolmark for the
washing of machine washable Woolmark products provided that the products are
washed according to the instructions on the garment label and those issued by
the manufacturer of this washing machine, M0509.
Quick Wash - For lightly soiled garments needed quickly.
Towels - For bath towels and washcloths. Due to their high absorbancy, wash no more than a half
load (6 pounds) of towels at a time for best results
Sanitize - For heavily soiled, colorfast garments. This cycle heats the water to 150°F to eliminate
bacteria.
NOTE: If Pause is selected during the heating portion of the Sanitize Cycle, your Washer door will
remain locked for your safety.
Bedding - For bulky items such as blankets and sheets.
Active Wear - For washable sportswear.
Eco Wash - For geographic areas where energy and water conservation is needed. It saves an
additional 5% of Energy and 5% of water consumption.
Rinse + Spin - Use for loads that need rinsing only or to add rinse-added fabric softener to a load.
Spin Only - Provides a spin to remove more water.
9.
Start/Pause selection button
Press to pause and restart programs.
10. Power button
Press once to turn your Washer on, press again to turn your Washer off. If left on for more than 10
minutes without any buttons being touched, the power automatically turns off.
NOTE : Cycles and options vary by model. Refer to cycle chart in Appendix.
C-3 SAMSUNG Clothes Washer Owner’s Instructions
Washing a Load of Laundry
CHILD LOCK
A function that prevents children from playing with your Washer.
ACTIVATING/DEACTIVATING
If you want to activate/deactivate the Child Lock function, press the Soil Level and Signal buttons at the
same time for 3 seconds.
How It Works:
1. Child Lock can be activated while your Washer is running.
2. Once you activate Child Lock, all controls (except for the Power button) will be locked until you
deactivate Child Lock.
3. The Child Lock button will be lit while it is in effect.
Note: When buttons, other than the Power button, do not respond, please check if the Child
Lock function is on.
GARMENT +
You can add or take out laundry items even after the wash has started, as long as the Garment+ light is
on. Pushing the Start/Pause button unlocks the door, unless the water is too hot or if there is too much
water in your Washer. If you are able to unlock the door and wish to continue the wash cycle, close the
door and press the Start/Pause button.
MY CYCLE
Allows you to activate your custom wash (temperature, spin, soil level, etc.) with one–button
convenience.
By pushing the My Cycle button, you activate the settings used during the last My Cycle mode. The My
Cycle light will indicate activation.
You can select all options as follows in My Cycle mode.
1. Select cycle using Cycle Selector dial.
2. After cycle selection, set each option.
Note: At this time, the option will follow as per each cycle’s default option selection.
3. Then, you can start My Cycle by pushing the Start/Pause button in My Cycle mode.
The cycle and options you select will be displayed next time you choose My Cycle.
Note: You can change My Cycle setting by repeating same process above.
The last used setting will be displayed at the next time you choose My Cycle.
SAMSUNG Clothes Washer Owner’s Instructions C-4
Washing a Load of Laundry
FOR SILVERCARE™ WASHING (select models)
An increased consumer demand for energy-saving products prompted Samsung to develop a system to
use silver, widely known for its antimicrobial properties, as a sanitizing agent in your washing machine.
Pure silver atoms have an electron stripped away by electrolysis during the wash and rinse cycles, which
releases up to 16 million trillion silver ions that then penetrate deep into the fabric to sanitize clothing
(according to U.S. EPA Test Guideline DIS/TSS-13) without the need for hot water or bleach.
Here’s how it works: A grapefruit-sized device alongside the tub uses two pure silver plates the size of
large chewing gum sticks as electrodes in the water inlet system. The resulting positively charged silver
atoms - Silver ions (Ag+) -- are sprayed into the tub during the wash and final rinse cycle.
This process removed or killed greater than 99.9% of tested bacteria.
Samsung’s SilverCare™ Technology provides a 92% energy savings over hot water sanitization. Extra
delicate blouses, shirts, or even lingerie that can’t be washed in hot water can now be sanitized
effectively without the adverse effects of hot water sanitization that is normally a concern with those
types of articles. The silver plates carry a warranty of ten years, and can easily be replaced by a Service
Technician if so needed.
1. Load the washer.
2. Press the Power button.
3. Select a Cycle by turning the Cycle Selection dial.
4. Press SilverCare™ button.
5. Add detergent in the dispenser tray for main washing, and add fabric softener up to the marked line.
6. Press the Start/Pause button.
: The washer automatically selects optimal washing conditions by sensing the laundry’s weight.
Note :
FOR HOME USE ONLY– COMMERCIAL USERS SHOULD NOTIFY THEIR LOCAL WASTE TREATMENT
AUTHORITIES BEFORE USE
The total number of silver cycles run by the washer is displayed when pushing the Signal button and the
SilverCare™ button.
LU3 : less than 1000 times
LU2 : between 1000 to 2000 times
LU1 : between 2000 to 2999 times
LU0 : over 2999 times
You should replace the SilverCare™ kit when the display reads “LU0” as the electrodes are near the end of
their useful life. Contact 1-800-SAMSUNG.
Note :
For some models that have no heater if you choose SilverCare™, the temperature will be automatically
set to to Cold/Cold.
You cannot choose the SilverCare™ option with the Wool cycle.
C-5 SAMSUNG Clothes Washer Owner’s Instructions
Washing a Load of Laundry
DETERGENT USE
Your Washer is designed to use high efficiency (HE) detergents.
• For best cleaning results, use a high efficiency detergent such as Tide HE, Wisk
HE, Cheer HE or Gain HE*. High efficiency detergents contain suds suppressors
that reduce or eliminate suds. When fewer suds are produced, the load tumbles
more efficiently and cleaning is maximized.
! WARNING
Regular detergent is Not recommended. Please use only HE detergent.
NOTE: Reducing the amount of detergent may reduce cleaning. It is important to pre–treat stains, sort
carefully by color and soil level, and avoid overloading.
* Brand names are trademarks of their respective manufacturers.
FEATURES
AUTOMATIC DISPENSER
Your Washer has separate compartments for dispensing
detergent and color-safe bleach, chlorine bleach, and fabric
Prewash (select models)
softener. All laundry additives are added to their respective
compartments before starting your Washer.
Detergent
The automatic dispenser MUST ALWAYS be in place before
Selector
starting your Washer.
DO NOT open the automatic dispenser when your Washer is
Detergent
running.
Compartment
To use:
1. Pull out the dispenser drawer on the left side of the
control panel.
2. Add recommended quantity of additive to the
appropriate compartments with laundry additives,being
careful not to overfill or spill.
3. Slide the dispenser drawer carefully and completely back into the compartment.
DETERGENT COMPARTMENT
1. Pour the recommended amount of laundry detergent directly into the detergent compartment
before starting your Washer.
2. If color-safe bleach is to be used, it should be added with detergent to the detergent
compartment.
• When adding color-safe bleach with detergent, it is best if both laundry products are in the
same form – granular or liquid.
NOTE: If using liquid detergent, lower the detergent selector and add the detergent to the
detergent compartment.
SAMSUNG Clothes Washer Owner’s Instructions C-6
Washing a Load of Laundry
PRE WASH COMPARTMENT (SELECT MODELS)
When using the Pre Wash option (select models), detergent should be added to both the Pre Wash
compartment and the detergent compartment. The detergent will automatically be dispensed during
Pre Wash.
• If high efficiency (HE) detergent is used, add 1/3 of the recommended amount to the Pre Wash
compartment and 2/3 of the recommended amount to the detergent compartment.
BLEACH COMPARTMENT
(Liquid chlorine bleach only)
Bleach
1. Add chlorine bleach to the bleach compartment.
Compartment
DO NOT exceed the MAX FILL line.
2. Avoid splashing or over–filling the compartment.
Fabric Softner
Compartment
3. Your Washer automatically dispenses bleach into the tub
at the appropriate time.
4. The dispenser automatically dilutes liquid chlorine
bleach before it reaches the wash load.
NOTES:
• Never pour undiluted liquid chlorine bleach directly
onto the load or into the tub. It is a powerful chemical
and can cause fabric damage, such as weakening of
the fibers or color loss, if not used properly.
• If you prefer to use color–safe, non–chlorine bleach, add it to the appropriate detergent
compartment.
DO NOT pour color–safe bleach into the chlorine bleach dispenser.
FABRIC SOFTENER COMPARTMENT
1. Pour the recommended amount of liquid fabric softener into the softener compartment.
For smaller loads, use less than one capful.
2. Fabric softener should be diluted with water until it reaches MAX FILL in the compartment.
3. The dispenser automatically releases liquid fabric softener at the proper time during the rinse
cycle.
NOTES:
• Use the softener compartment ONLY for liquid fabric softeners.
• DO NOT use the Downy Ball* with this Washer. It will not add fabric softener at the appropriate
time.
Use the automatic dispenser.
* Brand names are trademarks of their respective manufacturers.
C-7 SAMSUNG Clothes Washer Owner’s Instructions
Maintaining Your Washer
CLEANING THE EXTERIOR
Turn off the water faucets after finishing the day’s washing.
This will shut off the water supply to your Washer and prevent the unlikely possibility of damage from
escaping water. Leave the door open to allow the inside of your Washer to dry out.
Use a soft cloth to wipe up all detergent, bleach or other spills as they occur.
Clean the following as recommended:
Control Panel – Clean with a soft, damp cloth. Do not use abrasive powders or cleaning pads.
Do not spray cleaners directly on the panel.
Cabinet – Clean with soap and water.
CLEANING THE INTERIOR
Clean the interior of your Washer periodically to remove any dirt, soil, odor, mold, mildew, or bacterial
residue that may remain in your Washer as a result of washing clothes.
Failure to follow these instructions may result in unsatisfactory conditions, including unpleasant odor
and/or permanent stains on your Washer or laundry.
Hard water deposits may be removed, if needed. Use a cleaner labeled “Washer safe”.
CLEANING THE DISPENSERS
The Automatic Dispenser may need to be cleaned periodically due to
laundry additive buildup.
1. Press the release lever on the inside of the dispenser and pull out.
2. Remove the cups from the fabric softener and bleach compartments.
3. Wash all of the parts under running water.
4. Clean the dispenser recess with a soft brush.
5. Reinsert the cups, pushing them firmly into place.
6. Push the dispenser back into place.
7. Run a Rinse & Spin cycle without any load in your Washer.
Siphon Cap
STORING YOUR WASHER
Washers can be damaged if water is not removed from hoses and internal components before storage.
Prepare your Washer for storage as follows:
• Select the Quick Wash cycle and add bleach to the automatic dispenser. Run your Washer through
the cycle without a load.
• Turn the water faucets off and disconnect the inlet hoses.
• Unplug your Washer from the electrical outlet and leave your Washer door open to let air circulate
inside the tumbler.
• If your Washer has been stored in below–freezing temperatures, allow time for any leftover water in
your Washer to thaw out before use.
SAMSUNG Clothes Washer Owner’s Instructions D-1
Troubleshooting
CHECK THESE POINTS IF YOUR WASHER...
will not start..
•
•
•
•
•
•
has no water or not
enough water..
•
•
•
•
has detergent remains
in the automatic
dispenser after the
wash cycle is complete.
vibrates or is too noisy.
stops
•
•
•
•
•
•
•
•
•
•
•
•
•
Make sure door is firmly closed.
Make sure your Washer is plugged in.
Make sure the water source faucets are turned on.
Make sure to press the Cycle Selector dial to start your Washer.
Make sure the Child Lock is not activated; see page C4.
Before your Washer starts to fill, it will make a series of clicking noises
to check the door lock and do a quick drain.
Turn both faucets on fully.
Make sure the door is tightly closed.
Straighten water inlet hoses.
Disconnect hoses and clean screens. Hose filter screens may be
plugged.
Open and close the door, then press the Cycle Selector dial.
Make sure your Washer is running with sufficient water pressure.
Make sure the Detergent Selector dial is in the upper position when
using granular detergent.
Make sure your Washer is set on a level surface. If the surface is not
level, adjust your Washer feet to level the appliance.
Make sure that the shipping bolts are removed.
Make sure your Washer is not touching any other object.
Make sure the laundry load is balanced.
Plug cord into live electrical outlet.
Check fuse or reset circuit breaker.
Close door and press the Cycle Selector dial to start your Washer. For
your safety, your Washer will not tumble or spin unless the door is
closed.
Before your Washer starts to fill, it will make a series of clicking noises
to check the door lock and do a quick drain.
There may be a pause or soak period in the cycle. Wait briefly and it
may start.
Check screens on inlet hoses at the faucets for obstructions. Clean
screens periodically.
E-1 SAMSUNG Clothes Washer Owner’s Instructions
Troubleshooting
fills with the wrong
temperature water.
•
•
•
•
•
•
•
door locked shut or
will not open.
•
•
does not drain and/or
spin.
•
•
•
•
load is too wet at the
end of the cycle.
•
•
•
leaks water.
•
•
•
has excessive suds.
•
•
•
•
•
Turn both faucets on fully.
Make sure temperature selection is correct.
Make sure hoses are connected to correct faucets. Flush water lines.
Check the water heater. It should be set to deliver a minimum 120°
F (49° C) hot water at the tap. Also check water heater capacity and
recovery rate.
Disconnect hoses and clean screens. Hose filter screens may be
plugged.
As your Washer is filling, the water temperature may change as
the automatic temperature control feature checks incoming water
temperature. This is normal.
While your Washer is filling, you may notice just hot and/or just
cold water going through the dispenser when cold or warm wash
temperatures are selected. This is a normal function of the automatic
temperature control feature as your Washer determines the
temperature of the water.
Press the Cycle Selector dial to stop your Washer.
Your Washer door will remain locked during the heating portion of the
Sanitize Cycle
It may take a few moments for the door lock mechanism to disengage.
Check fuse or reset circuit breaker.
Straighten drain hoses. Eliminate kinked hoses. If there is a drain
restriction, call for service.
Close the door and press the Cycle Selector dial. For your safety, your
Washer will not tumble or spin unless the door is closed.
Use the High or Extra High spin speed.
Use high efficiency detergent to reduce over–sudsing.
Load is too small. Very small loads (one or two items) may become
unbalanced and not spin out completely.
Make sure door is firmly closed.
Make sure hose connections are tight.
Make sure end of drain hose is correctly inserted and secured to drain
facility.
Avoid overloading.
Use high efficiency detergent to prevent over–sudsing.
Use high efficiency detergent to prevent over-sudsing.
Reduce detergent amount for soft water, small or lightly soiled loads.
Non-HE detergent is NOT recommended.
SAMSUNG Clothes Washer Owner’s Instructions E-2
Troubleshooting
INFORMATION CODES
Information codes may be displayed to help you better understand what is occurring with your Washer.
Code Symbol
Meaning
Solution
Unbalanced load prevented your
Washer from spinning.
Redistribute the load, press the Cycle Selector
dial.
Door is unlocked when Washer
is running.
Press the Power button to turn off your Washer,
then restart the cycle. If the code reappears,
call for service. See below.
Door is open when Washer is
running.
Close the door tightly and restart the cycle.
If the code reappears, call for service.
See below.
Your Washer failed to lock the
door.
Close the door tightly and restart the cycle.
If the code reappears, call for service.
See below.
Water temperature control
problem.
(Heater Control problem)
Call for service. See below.
Your Washer has tried to fill but
has not reached the proper water
level.
Call for service. See below.
The door will not unlock.
Make sure the door is firmly closed.
Push the Power button to turn off your Washer,
then turn it on again. If the code reappears, call
for service. See below.
Motor not running properly.
Restart the cycle pressing the Cycle Selector
dial. If the code reappears, call for service.
See below.
Your washer is not draining.
But, it can light up when the unit
senses a brief restriction while
draining.
Before calling for service, check the following.
1) Turn off the unit and turn it on again.
2) Select the Spin Only
3) Press the Start/Pause to drain the water.
If it still does not drain, call for service.
Your Washer has tried to fill but
was unsuccessful.
Make sure the water faucets are open all the
way. Check for kinked hoses.
Check inlet screens on fill hoses.
E-3 SAMSUNG Clothes Washer Owner’s Instructions
Troubleshooting
Code Symbol
Meaning
Solution
Problem with control.
Call for service. See below.
Electric service was lost when
Washer was running.
Restart the cycle by pressing the Cycle Selector
dial.
A fault is detected in the water
level sensor.
Call for service
Jammed Key.
Call for service
Motor speed sensor problem.
Restart the cycle.
If the code reappears, call for service, see below
Temperature sensor problem.
Restart the cycle.
If the code reappears, call for service, see below
High current detected.
Restart the cycle.
If the code reappears, call for service, see below
High/Low voltage detected.
Restart the cycle.
If the code reappears, call for service, see below
Vibration sensor problem.
Restart the cycle.
If the code reappears, call for service, see below
SilverCare™ control problem
Restart the cycle.
If the code reappears, call for service, see
below.
Too much suds is detected
during the washing session. And,
the unit is put on hold until the
suds get reduced. Then, it will go
back to the operation. When it
finishes washing, End and SUdS
codes will blink in turn.
To prevent it, cut down on detergents.
For any codes not listed above, call 1–800–726–7864 (1–800–SAMSUNG)
SAMSUNG Clothes Washer Owner’s Instructions E-4
Appendix
FABRIC CARE CHART
The following symbols provide garment care directions without words. The care label will include, in
order, four symbols: washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of
symbols ensures consistency among garment manufacturers of domestic and imported items. Follow
care label directions to maximize garment life and reduce laundering problems.
Wash Cycle
Special Instructions
Warning Symbols for Laundering
Normal
Line Dry/ Hang
to Dry
Do Not Wash
Permanent Press/ Wrinkle
Resistant/ Wrinkle Control
Drip Dry
Do Not Wring
Gentle/Delicates
Dry Flat
Do Not Bleach
Hand Wash
Water Temperature**
Heat Setting
Do Not Tumble Dry
High
No Steam (added to iron)
Hot
Medium
Do Not Iron
Warm
Low
Cold
Any Heat
Bleach
No Heat/Air
Any Bleach (when needed)
Iron-Dry or Steam Temperatures
Line Dry/ Hang to Dry
Only Non-Chlorine
(color-safe)
Bleach (when needed)
High
Drip Dry
Tumble Dry Cycle
Medium
Dry Flat
Normal
Low
Permanent Press/ Wrinkle
Resistant/ Wrinkle Control
Gentle/ Delicates
Dryclean
For machine-washable
wool. Loads should be
under 8 pounds.
Dry Clean
Do Not Dry Clean
** The dot symbols represent appropriate wash water temperatures for various items. The
temperature range for Hot is 105° - 125° F/ 41° - 52°C, for Warm 85° - 105° F/29° - 41° C and for Cold
60° - 85° F/16° - 29° C. (Wash water temperature must be a minimum of 60° F/16°C for detergent
activation and effective cleaning.)
The clothes Washer may not ensure these temperatures because the actual water temperatures
entering your Washer are dependent on water heater settings and regional water supply
temperatures. For example, cold water entering the home in the northern states during winter
may be 40° F/4° C which is too cold for effective cleaning. The water temperature in this situation
will need to be adjusted by selecting a warm setting, adding some hot water to the MAX FILL line
or using your Washer’s heating option, if available.
F-1 SAMSUNG Clothes Washer Owner’s Instructions
Appendix
HELPING THE ENVIRONMENT
•
•
•
•
•
Your Washer is manufactured from recyclable materials. If you decide to dispose of it, please
observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be
connected to a power source.
Remove the door so that animals and small children cannot get trapped inside the appliance.
Do not exceed the detergent quantities recommended in the detergent manufacturers’
instructions.
Use stain removal products and bleaches before the wash cycle only when strictly necessary.
Save water and electricity by only washing full loads (the exact amount depends upon the
program used).
Use SilverCare™ instead of Hot Water Sanitization to save energy.
DECLARATION OF CONFORMITY
This appliance complies with UL2157.
SPECIFICATION
TYPE
FRONT LOADING WASHER
DIMENSION
Div
Inches (cm)
Div
Inches (cm)
A. Height
- Overall
38” (96.5)
C. Depth with
door open 90°
49” (124.5)
B. Width
27” (68.6)
D. Depth
30.25” (77.0)
WATER PRESSURE
50 kPa ~ 800 kPa
WEIGHT
89.9 kg
HEATER RATING
POWER CONSUMPTION
SPIN REVOLUTION
3.29 Cu.ft
WASHING
120 V
226W
WASHING AND HEATING
120 V
997W
SPIN
120 V
379W
DRAIN
120 V
41W
WF326 *
1200rpm
WF316 * , WF317*
1100rpm
WF306 * , WF307*
1000rpm
WF206 * , WF207*
1000rpm
C
D
A
B
SAMSUNG Clothes Washer Owner’s Instructions F-2
Appendix
CYCLE CHART
WF326***
Functions
Temp
Options
Spin
EH/C H/C W/W W/C C/C
Soil Level
EH
H
M
L
NS
H
N
L
Delay Extra Extra
Start Wash Rinse
My
Cycle
Prewash
Extra Silver- Time
Spin Care™
Heavy
Duty



















92
Normal



















53
Whites



















62
Perm
Press

















47
Delicates/
Hand
Wash












41



Wool


Quick
Wash













Towels
































Sanitize


66



112



71

51


47



20


























Active
Wear
























Spin Only



Rinse +
Spin
35





Bedding
Eco Wash
57

F-3 SAMSUNG Clothes Washer Owner’s Instructions


11
Appendix
WF206*** , WF207***
Functions
Temp
Options
Spin
Soil Level
Delay Start Extra Wash Extra Rinse
Time
H/C W/W W/C
C/C
H
M
L
NS
H
N
L
Heavy Duty














67
Normal














53
Whites














62













47













66







20





Perm Press
Towels
Rinse + Spin
Spin Only

11
SAMSUNG Clothes Washer Owner’s Instructions F-4
Appendix
WF316***, WF317***
Functions
Temp
Options
Spin
EH/C H/C W/W W/C C/C
Soil Level
EH
H
M
L
NS
H
N
L
Delay Extra Extra
Start Wash Rinse
My
Cycle
Pre- Silver- Time
wash Care™
Heavy
Duty


















92
Normal


















53
Whites


















62
Perm
Press
















47
Delicates/
Hand
Wash












41



Wool


Quick
Wash













Towels



























Sanitize
Bedding
Rinse +
Spin
Spin Only





35


66



112




71



20




















F-5 SAMSUNG Clothes Washer Owner’s Instructions



57


11
Appendix
306BHW , WF307***
Functions
Temp
Options
Spin
EH/C H/C W/W W/C C/C
Soil Level
H
M
L
NS
H
N
L
Delay
Start
Extra
Wash
Extra
Rinse
SilverCare™
(306BHW Only)
Time
Heavy Duty















67
Normal















53
Whites















62
Perm Press














47
Delicates/
Hand Wash











41



Wool

Quick Wash












Towels



































Sanitize
Bedding
Rinse + Spin
Spin Only





57



35



66




112




71


20
11
SAMSUNG Clothes Washer Owner’s Instructions F-6
Appendix
SAMSUNG SILVERCARE™ WASHER
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
(SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted
by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty
period of:
One (1) Year All Parts and Labor, Two (2) Years Control Board Parts, Five (5) Years Motor, Three
Thousand (3,000) cycles or Ten (10) Years, whichever comes first for Silver Plates, and Lifetime
Stainless Tub
One (1) Year All Parts and Labor, Two (2) Years Control Board Parts, Five (5) Years Motor, Three Thousand
(3,000) cycles or Ten (10) Years, whichever comes first for Silver Plates, and Lifetime Stainless Tub
This limited warranty begins on the original date of purchase, and is valid only on products purchased
and used in the United States. To receive warranty service, the purchaser must contact SAMSUNG for
problem determination and service procedures. Warranty service can only be performed by a SAMSUNG
authorized service center. The original dated bill of sale must be presented upon request as proof of
purchase to SAMSUNG or SAMSUNG’s authorized service center. SAMSUNG will provide in-home service
during the warranty period at no charge, subject to availability within the contiguous United States. Inhome service is not available in all areas.
To receive in-home service, product must be unobstructed and accessible to the service agent. If service
is not available, SAMSUNG may elect to provide transportation of the product to and from an authorized
service center.
SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein,
with new or reconditioned parts or products if found to be defective during the limited warranty period
specified above. All replaced parts and products become the property of SAMSUNG and must be
returned to SAMSUNG. Replacement parts and products assume the remaining original warranty, or
ninety (90) days, whichever is longer.
This limited warranty covers manufacturing defects in materials and workmanship encountered in
normal, noncommercial use of this product and shall not apply to the following: damage that occurs
in shipment; delivery and installation; applications and uses for which this product was not intended;
altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire,
water, lightning, or other acts of nature or God; use of products, equipment, systems, utilities, services,
parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied
or authorized by SAMSUNG that damage this product or result in service problems; incorrect electrical
line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions,
maintenance and environmental instructions that are covered and prescribed in the instruction book;
product removal and reinstallation; problems caused by pest infestations. This limited warranty does
not cover problems resulting from incorrect electric current, voltage or supply, light bulbs, house fuses,
house wiring, cost of a service call for instructions, or fixing installation errors. SAMSUNG does not
warrant uninterrupted or error-free operation of the product.
F-7 SAMSUNG Clothes Washer Owner’s Instructions
Appendix
EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR
IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO
WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS
PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE
OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT,
REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE.
WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS,
DAMAGE, OR INJURY TO PURCHASER AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR
PROPERTY ARISING OUT OF THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS
PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or
limitation of incidental or consequential damages, so the above limitations or exclusions may not apply
to you. This warranty gives you specific rights, and you may also have other rights, which vary from state
to state.
To obtain warranty service, please contact SAMSUNG at:
SAMSUNG ELECTRONICS AMERICA, INC. – CONSUMER ELECTRONICS CUSTOMER SERVICE
400 Valley Road, Suite 201, Mt. Arlington, NJ 07856
1-800-SAMSUNG (1-800-726-7864)
www.samsung.com
SAMSUNG Clothes Washer Owner’s Instructions F-8
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please
contact the SAMSUNG customer care center.
Samsung Electronics America, Inc.
1-800-SAMSUNG (726-7864)
www.samsung.com
Download PDF