Zephyr | Firenze ZFI-M90BS | Installation guide | Zephyr Firenze ZFI-M90BS Installation guide

Use, Care, and Installation Guide
www.zephyronline.com
Firenze
ZFI-M90BS
Model number:
Serial Number:
JAN11.0401 © Zephyr Corporation
www.zephyronline.com
INSTALLATION
Ducting Calculation Sheet .......................................
Mounting Height & Clearance................................
Ducting Options ...........................................................
Hood Specifications ...................................................
Mounting the Range Hood ......................................
Ductless Recirculating ..............................................
5
6
7
8
9
10
FEATURES & CONTROLS
Electronic LED Controls ........................................... 11
MAINTENANCE
Hood and Filter Cleaning ......................................... 12
TROUBLESHOOTING................................................................ 13
WIRING DIAGRAMS ................................................................... 14
LIST OF PARTS AND ACCESSORIES .............................. 15
1
Table of Contents
SAFETY NOTICE ................................................................. 2-3
LIST OF MATERIALS ....................................................... 4
www.zephyronline.com
Important Safety Notice
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.
WARNING
TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
CAUTION
For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning
agents or detergents. Suitable for use in household cooking area.
WARNING
TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:
a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly
on low or medium settings.
b. Always turn hood ON when cooking at high heat or when flaming food
c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
d. Use proper pan size. Always use cookware appropriate for the size of the surface element.
e. Keep fan, filters and grease laden surfaces clean.
f. Use high setting on hood only when necessary.
g. Don’t leave hood unattended when cooking.
h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:
a. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b. NEVER PICK UP A FLAMING PAN – You may be burned.
c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
d. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards.
Including fire-rated construction.
b. Sufficient air is needed for power combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent
back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National
Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and
the local code authorities.
c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d. Ducted fans must always vent to the outdoors.
e. NEVER place a switch where it can be reached from a tub or shower.
f. Make sure the power is off before installing, wiring or maintenancing.
2
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
CAUTION
To reduce risk of fire and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings,
attics, crawl spaces or garages.
OPERATION
Always leave safety grilles and filters in place. Without these components, operating blowers could catch onto hair, fingers
and loose clothing.
The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,
maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to
negligence and the warranty of the unit automatically expires due to improper maintenance.
*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.
ELECTRICAL REQUIREMENTS
Important:
Observe all governing codes and ordinances.
It is the customer’s responsibility:
- To contact a qualified electrical installer.
- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70
latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and
all local codes and ordinances.
If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the
ground path is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure the range hood is properly grounded.
Do not have a fuse in the neutral or ground circuit.
*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575
This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit
protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to
Electrical Diagram on product.
A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase
and install appropriate connector if necessary.
ZFI-M90BS - 320 Watts, 2.8 Amps
3
Important Safety Notice
WARNING
List of Materials
www.zephyronline.com
MODELS: ZFI-M90BS
PARTS SUPPLIED
1 - Hood with internal blower
2 - Aluminum mesh filters
1 - Duct cover assembly (top and bottom)
1 - Duct cover wall bracket
4 - 3W LED light bulbs
1 - 6” round backdraft damper (pre-installed)
1 - Hardware package
HARDWARE PACKAGE CONTENTS
M4 x 8 (2)
M6 x 1-1/2” (3)
M6 x 1” (2)
Wire Nuts (3)
PARTS NOT SUPPLIED
- Ducting, conduit and all installation tools
- Cable connector (if required by local codes)
- Duct cover extension accessory
- Recirculating kit accessory
4
Equivalent number
length x used
=
Duct pieces
Total
Total
3-1/ 4” x 10” 1 Ft.
Rect.,
straight
x(
) =
Ft.
6”- 8” Round 30 Ft.
wall cap
with damper
x(
) =
Ft.
7” Round,
straight
1 Ft.
x(
) =
Ft.
6”- 8” Round, 30 Ft.
roof cap
x(
) =
Ft.
8” Round,
straight
1 Ft.
x(
) =
Ft.
6” round to
1 Ft.
3-1/ 4” x 10”
rect.
transition
x(
) =
Ft.
3-1/ 4” x 10” 15 Ft.
Rect. 90 0
elbow
x(
) =
Ft.
x(
) =
Ft.
3-1/ 4” x 10” 9 Ft.
Rect. 45 0
elbow
x(
) =
Ft.
6” round to
16 Ft.
3-1/ 4” x 10”
rect.
transition
90 0 elbow
7” or 8”
Round,
90 0 elbow
15 Ft.
x(
) =
Ft.
3-1/ 4” x 10” 24 Ft.
Rect. 90 0
flat elbow
x(
7” or 8”
Round,
45 0 elbow
9 Ft.
x(
) =
Ft.
3-1/ 4” x 10” 30 Ft.
Rect.
wall cap
with damper
x(
7” or 8”
30 Ft.
Round
wall cap
with damper
x(
) =
Ft.
3-1/ 4” x 10” 5 Ft.
Rect. to
6” round
transition
x(
) =
Ft.
7” or 8”
Round,
roof cap
x(
) =
Ft.
3-1/ 4” x 10” 20 Ft.
Rect. to
6” round
transition
90 0 elbow
x(
) =
Ft.
7” round to
8 Ft.
3 1/ 4” x 10”
rect.
transition
x(
) =
Ft.
) =
Ft.
15 Ft.
x(
) =
Ft.
7” round to
23 Ft.
3-1/ 4” x 10”
rect.
transition
90 0 elbow
x(
6” Round,
90 0 elbow
6” Round,
45 0 elbow
9 Ft.
x(
) =
Ft.
Subtotal column 2 =
Ft.
Subtotal column 1 =
Ft.
Total ductwork
Ft.
) =
) =
Subtotal column 1 =
Ft.
Ft.
Ft.
Maximum Duct Length: For satisfactory air movement,
the total duct length of a 3 1/ 4” x 10” rectangular 6” or 7”
diameter round duct should not exceed 100 equivalent feet.
5
30 Ft.
=
Installation – Ducting Calculation Sheet
Equivalent number
length x used
=
Duct pieces
Installation – Mounting Height & Clearance
www.zephyronline.com
ALWAYS, when possible, reduce the number of
transitions and turns. If a long duct run is required,
increase duct size from 6” to 7” or 8”.
If turns or transitions are required: Install as far
away from duct opening and as far apart between
the two transitions as possible.
A
n.
mi . B
n
mi . C
x
ma
D
n.
mi . E
n
i
m .F
x
ma
Minimum mount height between range top to hood
bottom should be no less than 26”.
in.
” m x.
26” ma
34
Maximum mount height should be no higher than
34”.
It is important to install the hood at the proper
mounting height. Hoods mounted too low could
result in heat damage and fire hazard; while hoods
mounted too high will be hard to reach and will
loose its performance and efficiency.
”
36
If available, also refer to range manufacturer’s
height clearance requirements and recommended
hood mounting height above range. Always check
your local codes for any differences.
Hood Heights
minimum ducted (A)
minimum recirculating (B)
maximum (C)
Standard
Duct Cover
26-1/2”
31”
50”
Extension
Duct Cover
41-1/2“
45-1/2“
80”
Duct cover extension kit available for ceiling
heights up to 12 feet. Turn to page 15 for part
number and ordering information.
Ceiling Heights
minimum ducted (D) 88-1/2” (7’ 4-1/2”) 103-1/2“ (8‘ 7-1/2”)
minimum recirculating (E) 93” (7’ 9”)
107-1/2“ (8‘ 11-1/2”)
maximum (F) 120” (10’)
150” (12’ 6”)
DUCTING
A minimum of 6” round duct is recomended to
maintain maximum air flow efficiency.
Always use rigid type metal ducts only. Flexible
ducts could restrict air flow by up to 50%.
Use calculation worksheet to compute total duct
work (Page 5).
6
DAMAGE-SHIPMENT / INSTALLATION:
• Please fully inspect unit for damage before
installation.
• If the unit is damaged in shipment, return the
unit to the store in which it was bought for
repair or replacement.
• If the unit is damaged by the customer, repair
or replacement is the responsibility of the
customer.
• If the unit is damaged by the installer (if other
than the customer), repair of replacement must
be made by arrangement between customer
and installer.
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.
All exhaust must be ducted to the outside, unless using the recirculating option.
Use single wall rigid Metal ductwork only.
Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or Duct Tape.
Some Ducting Options
Roof Pitch w/
Flashing & Cap
(blower
housing)
(blower
housing)
side wall cap
w/ gravity damper
Soffit or crawl space
(blower
housing)
ductless
recirculating
side wall cap
w/ gravity damper
(blower
housing)
7
Installation – Ducting Options
WARNING FIRE HAZARD
FRONT VIEW
SIDE VIEW
10 3/8”
10 9/16”
1 5/8”
STANDARD
min. ducted - 26 1/2”
min. recirc. - 31”
max. - 50”
15 3/4”
3 1/8”
Z1C-01FI
min. ducted - 41 1/2”
min. recirc. - 45 1/2”
max. - 80”
19 11/16”
35 7/16”
3 15/16”
TOP VIEW
4 7/16”
Installation – Hood Specifications
www.zephyronline.com
AC In
8
51
5/1
6”
2. Plum and mark center line.
3. Mark mounting height line B. (16-1/4” from line A)
4. Mark mounting spread from C/L. (8-7/8”)
5. Fasten (2) M6 x 1-1/2” screws into studs on line B but
do not tighten all the way. Note: Wood blocking may
need to be added behind the drywall if no studs are
present. Wall anchors may also be used but check
local codes before using wall anchors.
16-1/4”
6. Remove the (2) aluminum mesh filters.
7. Hang hood onto the mounting screws and hand tighten
each screw. (FIG. A) Secure third M6 x 1-1/2” screw
through inside of hood into wall for extra support. (FIG.
A #2)
26” min
8. Center and attach duct cover mounting bracket to wall
just below the ceiling or soffit using (2) M6 x 1” screws.
Brackets are
pre-installed
9. Install electrical and duct work. Seal duct work with
aluminum duct tape.
10. Power up hood and check for leaks around duct tape.
11. Place telescopic duct covers onto hood and extend
inner (top) duct cover upwards and secure to duct
cover bracket using (2) M4 x 8 screws.
12. Re-install the (2) aluminum mesh filters.
2
* If using hood in recirculating mode you must secure the
air diverter plate onto wall before installing duct work
and duct covers. Turn to page 10 for more details.
FIG. A
! WARNING: Electrical wiring must be done by a qualified person(s) in
accordance with all applicable codes and standards. This range hood must be
properly grounded. Turn off electrical power at service entrance before wiring.
Cable Lock
A cable locking connector (not supplied) might
be required by local codes. Check with local
requirements and codes, purchase and install
appropriate connector if necessary.
Cable Lock
9
Installation – Mounting the Hood
! CAUTION: At least two installers are
required due to the weight and size of the
hood.
1. Measure from range top to hood bottom and mark line
A. (26” minimum from range top) .
Installation – Ductless Recirculating
www.zephyronline.com
Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed.
When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust
from cooking are drawn and filtered by a set of optional charcoal filters. The air is then purified and recirculated back within the home.
We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new duct
work, if possible. The hood is most effective and efficient as an exhaust hood. Only when the exhaust option
is not possible should you recourse to converting the hood into a recirculating hood.
When converted to be a recirculating hood, a set of charcoal filters are required on top of its standard
Aluminum Mesh Filter set. Order according to its Part number below. The standard Aluminum Mesh Filters
are intended to capture residue from cooking and the optional charcoal filters help to purify fumes exhausted
from cooking for re-circulation.
RECIRCULATING KIT (REQUIRED IF NO DUCTING IS USED)
Kit includes charcoal filters, charcoal filter brackets and air diverter plate.
Hood Model
ZFI-M90BS
Part No.
ZRC-00FI
Filters in Pkg.
2
1. Purchase recirculating kit per the part number above
2. Secure air diverter plate to wall below duct cover bracket. (FIG. B)
Run 6” ducting from top of hood and secure to air diverter plate.
See manual included with recirculating kit for more detailed
instructions.
3. Remove aluminum mesh filters from hood. Install charcoal filter
brackets inside filter opening. Note: screws to secure charcoal filter
brackets are already pre-installed in the hood and must first be
removed. Clip charcoal filters onto each charcoal filter bracket. (FIG. B)
4. Re-Install aluminum mesh filters.
5. Charcoal filters must be replaced after every 120 hours of use
(or approximately every 3 to 4 months based on the average of 1 - 2
hrs. of daily cooking time).
Charcoal Filter Replacements
Hood Model
ZFI-M90BS
Part No.
Z0F-C002
Qty to Order
2
DO NOT WASH CHARCOAL FILTERS. Charcoal filters may need
to be changed more often depending on cooking habits.
10
FIG. B
3 Lights Normal/Dim/Off
Blower Speed Selection 2
Power Button
Press
to switch blower on and off. If lights are on they will also
switch off when this button is pressed.
These controls feature a memory function that will remember the last
setting before being powered off. For example: If blower is on Speed 2
and lights are on normal and the Power Button is pressed, the entire
hood will power down. If Power Button is pressed again the blower will
switch back on to Speed 2 and lights on normal.
Blower Speed Selection
Press one of these buttons to select blower speeds 1, 2, and 3. While
blower is on a blue LED back-light will illuminate the applicable Speed
Selection button and Power On/Off button.
3 Lights Normal/Dim/Off
Press
to cycle through light levels Normal, Dim, and Off. While lights
are on a blue LED back-light will illuminate the button.
11
Features & Controls - Electronic LED Controls
1 Power Button
Maintenance – Hood and Filter Cleaning
www.zephyronline.com
SURFACE MAINTENANCE:
Clean the hood surface periodically with hot soapy water and clean cotton cloth. Do not use corrosive or
abrasive detergent , or steel wool/scouring pads which will scratch and damage surface.
For heavier soil use liquid degreaser.
After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and
buff out the stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.
Do not use any product containing chlorine bleach. Do not use “orange” cleaners.
Aluminum Mesh Filters
The aluminum mesh filters installed by the factory are intended to filter out residue and grease from
cooking. They need not be replaced on a regular basis but are required to be kept clean.
Remove and clean by hand or in dishwasher on low heat. Spray degreasing detergent and leave to soak if
heavily soiled.
Dry filters and re-install before using hood.
Removing Aluminum Mesh Filters
1. Push in on spring loaded handle
2. Pull down on filter hande to remove filter
Should filters wear out due to age and prolonged use,
replace with following part number:
Hood Model:
ZFI-M90BS
Part No.
50200042
Qty to Order
2
12
Issue
Cause
What to do
After installation,
the unit doesn’t
work.
1. The power source is not turned ON.
1. Make sure the circuit breaker and the unit’s
power is ON.
2. The power line and the cable locking connector
is not connecting properly.
2. Check the power connection with the unit is
connected properly.
3. The switch board and control board wirings are
disconnected.
3. Make sure the wirings between the switch
board and control board are connected
properly.
4. The switch board or control board is defective.
4. Change the switch board or control board.
1. The motor is defective, possibly seized.
1. Change the motor.
2. The thermally protected system detects if the
motor is too hot to operate and shuts the motor
down.
2. The motor will function properly after the
thermally protected system cool down.
3. Damaged capacitor.
3. Change the capacitor.
4. The switch board or control board is defective.
4. Change defective part.
1. The motor is not secure in place.
1. Tighten the motor in place.
2. Damaged blower wheel.
2. Replace the blower.
Light works,
but motor is not
turning.
The unit is
vibrating.
3. The hood is not secured in place.
3. Check the installation of the hood.
4. The switch board or control board is defective.
4. Change defective part.
The motor is
working, but the
lights are not.
1. Defective LED bulb.
1. Change the LED bulb.
2. The LED bulb plug is loose.
2. Connect the LED bulb plug.
The hood is
not venting out
properly.
1. The hood might be hanging too high from the
cook top.
1. Adjust the distance between the cook top and
the bottom of the hood within 26” and 34”
range.
2. The wind from the opened windows or opened
doors in the surrounding area are affecting the
ventilation of the hood.
2. Close all the windows and doors to eliminate
the outside wind flow.
3. Blockage in the duct opening or ductwork.
3. Remove all the blocking from the duct work or
duct opening.
4. The direction of duct opening is against the wind.
4. Adjust the duct opening direction.
5. Using the wrong size of ducting.
5. Change the ducting to at least 6” or higher for
the internal blower.
1.
1. Change the filter.
Metal Filter is
vibrating.
Filter is loose.
13
Troubleshooting
TROUBLESHOOTING PROCEDURES FOR FIRENZE
Wiring Diagrams
www.zephyronline.com
14
PART#
Replacement Parts
Light Bulb 3W LED (each)
Aluminum Mesh Filter (each)
Z0B-0032
50200042
Optional Accessories
Recirculating Kit
Replacement Charcoal Filter
Duct Cover Extension
ZRC-00FI
Z0F-C002
Z1C-01FI
To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368
15
List of Parts & Accessories
DESCRIPTION
STAPLE YOUR RECEIPT HERE
Proof of the original purchase
date is needed to obtain
service under warranty
Limited Warranty
TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call:
1-888-880-8368
Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein
as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or workmanship as follows:
Three Year Limited Warranty for Parts and LED lamps: For three years from the date of your original purchase of the
Products, we will provide, free of charge, Products or parts to replace those that failed due to manufacturing defects.
We may choose, in our sole discretion, to repair or replace parts before we elect to replace the Products.
One Year Limited Warranty for Labor: For one year from the date of your original purchase of the Products, we will
provide, free of charge, the labor cost associated with repairing the Products or parts to replace those that failed due to
manufacturing defects. After the first year from the date of your original purchase, you are responsible for all labor costs
associated with this warranty.
Warranty Exclusions: This warranty covers only repair or replacement, at our option, of defective Products or parts
and does not cover any other costs related to the Products including but not limited to: (a) normal maintenance and
service required for the Products and consumable parts such as metal and carbon filters and fuses; (b) any Products or
parts which have been subject to freight damage, misuse, negligence, accident, faulty installation or installation contrary
to recommended installation instructions, improper maintenance or repair (other than by us); (c) commercial use of the
Products or use otherwise inconsistent with its intended purpose; (d) natural wear of the finish of the Products or wear
caused by improper maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner products;
(e) chips, dents or cracks caused by abuse or misuse of the Products; (f) service trips to your home to teach you how to
use the Products; or (g) damage to the Products caused by accident, fire, floods or act of God. If you are outside our
service area, additional charges may apply for shipping costs for warranty repair at our designated service locations and
for the travel cost to have a service technician come to your home to repair, remove or reinstall the Products. After the
first year from the date of your original purchase, you are also responsible for all labor costs associated with this
warranty.
Limitations of Warranty. OUR OBLIGATION TO REPAIR OR REPLACE, AT OUR OPTION, SHALL BE YOUR SOLE
AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. WE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF
THE PRODUCTS. THE EXPRESS WARRANTIES IN THE PRECEDING SECTION ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER EXPRESS WARRANTIES. WE HEREBY DISCLAIM AND EXCLUDE ALL OTHER EXPRESS WARRANTIES FOR THE PRODUCTS, AND DISCLAIM AND EXCLUDE ALL WARRANTIES IMPLIED BY LAW, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states or provinces do not
allow limitations on the duration of an implied warranty or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. To the extent that applicable law prohibits the exclusion of implied warranties, the duration of any applicable implied warranty is limited to the same two-year period
described above. Any oral or written description of the Products is for the sole purpose of identifying the Products and
shall not be construed as an express warranty. Prior to using, implementing or permitting use of the Products, you shall
determine the suitability of the Products for the intended use, and you shall assume all risk and liability whatsoever in
connection with such determination. We reserve the right to use functionally equivalent refurbished or reconditioned
parts or Products as warranty replacements or as part of warranty service. This warranty is not transferable from the
original purchaser and applies in the United States and Canada.
To Obtain Service Under Limited Warranty: To qualify for warranty service, you must: (a) notify us at the address or
telephone number stated below within 60 days of the discovery of the defect; (b) give the model number and part identification number and serial number; and (c) describe the nature of any defect in the Product or part. At the time of the
request for warranty service, you must present evidence of your proof of purchase and proof of the original purchase
date. If we determine that the warranty exclusions listed above apply or if you fail to provide the necessary documentation to obtain service, you will be responsible for all shipping, travel, labor and other costs related to the services.
Please check our website for any revisions, www.zephyronline.com.
Zephyr Corporation Service Department, 2277 Harbor Bay Parkway, Alameda, CA 94502 1-888-880-8368
MAR11.0201
Download PDF