Montigo | HL38VO | Owner`s manual | Montigo HL38VO Owner`s manual

fire feature
www.montigo.com
Installation Operation & Maintenance Manual
Check local codes and read all instructions prior to installation.
H38VO-ST Gas Fireplace
H38VO-ST
Outdoor
HL38VO-ST
Linear Outdoor
WARNING:
FOR OUTDOOR
USE ONLY
HL38VO-ST Outdoor Linear Shown
Warning:
Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to this manual. For assistance or additional
information consult a qualified installer, service agency or the gas supplier.
Safety Notice:
Glass doors on gas fireplaces are extremely hot while the fireplace is on and remain
hot even after the fireplace has been turned off. Safety screens are available and
can reduce the risks of severe burns.
For Your Safety:
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
®
C
XG0817(O)
US
Canadian Heating Products Inc. Langley, BC V4W 4A
Warning:
What to do if you smell gas
•
•
Do not try to light any appliance.
Do not touch any electrical
switch; do not use any phone in
your building.
• Immediately call your gas
supplier from a neighbor's
phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas
supplier, call the fire department.
• Installer: Leave this manual
with the appliance.
• Consumer: Leave this
manual for future reference.
Montigo Del Ray Corp. Ferndale, WA 98248
090109
H(L)38VO-ST Gas Fireplace
fire feature
Warning:
Read this manual before installing, operating or troubleshooting this
appliance. Please retain this owner's manual for future reference.
Congratulations
Congratulations on selecting a FireFeature gas fireplace, an elagent and well designed gas fireplace built to your specifications.
The Firefeature gas fireplace you have selected is designed to
provide the utmost in safety, reliability, and engineering standards.
This owner's manual should be retained for future reference. We
suggest that you keep it with all your other important documents
and product manuals.
As the owner of this new fireplace, you'll want to read and carefully follow all the instructions contained in this Installation,
Operations and Maintenance manual. Pay special attention to all
cautions, warnings, and Important warnings.
Your new FireFeature gas fireplace will give you years of
durable, reliable use. Welcome to the FireFeature family of gas
fireplace products.
The information contained in this owner's manual, unless noted
otherwise, applies to all models, and gas control systems.
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
• Important: Used to address practices not related to personal injury.
Table Of Contents
Congratulations
Safety Alert Key
Introduction................................................................................ 3
Installation
Installing and Framing the Fireplace..........................4 - 5
Installing the Gasline....................................................... 5
Finishing around the fireplace
Fireplace Facing................................................. 5
Mantels and Surrounds...................................... 5
Warranty .................................................................................. 12
Appendix
A. State of Massachusetts / Amendment..................... 13
Notes ...................................................................................... 14
Removing and Installing the Door..........................................5 - 6
Installing the LogSet.................................................................... 7
Operation ...........................................................................8 - 10
Wiring . ........................................................................ 10
Wiring for the Optional Fan Kit...................................... 10
Maintenance . ................................................................... 10 - 11
Troubleshooting............................................................. 11
Page 2
Part No. XG0817(O) - 090109
H(L)38VO-ST Gas Fireplace
fire feature
Introduction
Thank You for choosing a FireFeature Gas Fireplace.
About this Fireplace:
The H(L)38VO-ST is a Vent-free fireplace which is design exclusively for
outdoor use. It is available in Stainless steel with the Traditional logset
or in the linear-style burner. This fireplace is currently available in the
H38DVO-ST and HL38VO-ST models.
The H38VO-ST is rated for Natural Gas at 26,000 BTU/H (7.62 Kilowatts)
Input or Propane at 26,000 BTU/H (7.62 Kilowatts) Input.
► H38VO-ST; Vent Free, Millivolt Pilot.
► H38VO-ST-I; Vent Free, Intermittent Pilot (HSI).
► H38VO-ST-F; Vent Free, Electronic Ignition
The HL38VO-ST is rated for Natural Gas at 26,000 BTU/H (7.62 Kilowatts)
Input or Propane at 26,000 BTU/H (7.62 Kilowatts) Input.
► HL38VO-ST; Vent Free, Millivolt Pilot.
► HL38VO-ST-I; Vent Free, Intermittent Pilot (HSI).
► HL38VO-ST-F; Vent Free, Electronic Ignition
How to use this manual:
CAUTION!
Due to its high operating temperatures, the appliance
should be located out of traffic & away from furniture and
draperies.
 Children and adults should be alerted to the hazards
of the high surface temperature, which could cause
burns or clothing ignition.
 Young children should be carefully supervised when
they are in the same room as the appliance.
 Clothing or other flammable materials should not be
placed on or near the appliance.
WARNING!
When this appliance is installed directly on carpeting, tile or any
combustible material other than wood flooring, it must be installed
on a metal or wood panel extending the full width and depth of
the appliance.
This manual covers installation, operation and maintenance. Lighting,
operation and care of this fireplace can be easily performed by the
homeowner. However, all installation and service work should be
performed by a qualified or licensed installer, plumber, or gasfitter who
is qualified or licensed by the state, province, region, or governing body
in which the appliance is being installed.
This manual covers all models and unless otherwise specified, the
designation H38DF-SVO refers to all models. Sections which are
specific to a particular model are marked with a
symbol, plus
the appropriate model number.
Warranty and Installation Information:
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
►Modification of the fireplace and/or components including Direct-Vent assembly
or glass doors.
►Use of any component part not manufactured or approved by Montigo in
combination with this Montigo fireplace system.
►Installation other than as instructed in this manual.
Consult your local Gas Inspection Branch on installation requirements
for factory-built gas fireplaces. Installation & repairs should be done by
a qualified contractor.
Installations in Canada must conform to the current CAN/CGA B149.1 and .2 Gas Installation Code and local regulations. If the optional
air-circulating fan kit is installed, it must be electrically grounded in
accordance with CSA C22.1 Canadian Electrical Code Part 1 and/or
Local Codes.
Installations in the USA must conform to local codes, or in the absence
of local codes to the National Fuel Gas Code, ANSI Z223.1-1988. If the
optional air-circulating fan is installed, it must be grounded in accordance
with local codes or, in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70-1987. See Appendix A for installation
within the State of Massachusetts.
Part No. XG0817(O) - 090109
Installing The Fireplace Shell
The fireplace may be installed in a location that maintains clearances
to ALL exterior furniture, appliances and other exterior equipment.
Safety, as well as efficiency of operation, must be considered when
selecting the fireplace location. Try to select a location that does not
interfere with foot traffic, has adequate ventilation, and offers an accessible pathway for ventilated gasses. See page 4.
Page 3
H(L)38VO-ST Gas Fireplace
fire feature
Installation
The fireplace dimensions with the Optional Stainless steel cover,
shown below. (Note: This model is intended as a stand-alone).
Framing (stand-alone):
For Fireplace without the Optional Stainless steel surround.
40 1/8”
Overall
41”
25 1/8”
Depth
38”
Top View
40 1/8”
Overall
40”
6 3/4”
37 5/8”
Overall
34 5/8”
O/S Door
Frame
24 3/8”
O/S Door
Frame
25 3/4”
Opening
 Shaded area, Non-combustible framing.
 Dashed line, Non-combustible back-framing.
May not be exactly as shown. See Figure 2a
below. Both walls typical.
Figure 2. Framing dimensions (without Optional surround). Must be
back-framed as shown in Figure 2a below.
5 1/4”
Front View
Figure 1. Fireplace dimensions. (With Optional surround)
The fireplace dimensions without the Optional Stainless steel cover,
shown below. (Framing for the Fireplace without the Optional stainless steel cover shown below).
36 7/8”
41” (Opening)
Existing Combustible Structure
35 3/8”
Opening
Surrounding construction
(bottom, sides and top) must
be non-combustible materials,
metal studs,c oncrete board
and concrete ,brick, or stone.
30” Min
24”
23 7/8”
Backframe Min. 38”
both sides Typical
Figure 3. Framing dimensions (without Optional surround). Distance from
Existing Structures. (Please follow Appendix A - Termination
locations, when considering a location for your fireplace).
Top View
36 7/8”
6 3/4”
36 1/2”
34 5/8”
5/8”
34
O/S Door
Frame
Fr
24 3/8”
3/8”
24
O/S Door
Door
O/S
Frame
Frame
25 3/4”
Opening
5 1/4”
35 3/8”
Front View
Figure 1a. Fireplace dimensions. (Without Optional surround)
Page 4
Part No. XG0817(O) - 090109
H(L)38VO-ST Gas Fireplace
fire feature
Installation
When installing this fireplace as shown in Figure 5, the outer shell is not
to be installed. Follow Figures 2,3 (wall installation) and Figure 5 (MIN
size enclosure for patio or other contemporary installation) to frame
around the fireplace chassis.
Note: ONLY Non-combustible materials must be used in construction
of the enclosure. (top, bottom and sides). Steel studs in combination
with concrete, rock, or stone finishing materials, are acceptable. See
Figures 2, 3 and 5.
Removing and Installing
H38VO-ST
HL38VO-ST
the Door
Removing the door:
The doors are removed in a few simple steps. Follow these Steps below
to remove the Horizontal access panel, unlatch the door buckles and,
remove the door. Replace in reverse order.
Step 1: Remove the Horizontal Access Pan41”
Surrounding construction
(bottom, sides and top) must
be non-combustible materials,
metal studs, concrete board
and concrete,b rick, or stone.
Backframe Min. 38”
both sides Typical
Remove the Horizontal cover
by placing fingers in both finger
holes, then pushng away from
you and lifting out. Place it
Finger Holes
aside during maintenance or
cleaning.
Installed Gas
Install in reverse order.
Valve Cover
Figure 28. Removing and installing the the Horizontal Acess Panel
Step 2:
Locate the Door Buckles:
Figure 5. Back framing dimensions. (without Optional surround)
WARNING!
When this appliance is installed directly on exterior carpeting, tile
or any combustible material other than wood flooring, it must be
installed on a metal or wood panel extending the full width and
depth of the appliance.
Figure 28a. Loccate the door buckles. (Both Sides Typical)
Step 3:
Release the Door Buckles
Hand-hold
Door Latch Slot
Door Latch Hook
Figure 28b. Door buckle Tool
Step 4:
Firmly grasp hand-hold
end of Door buckle tool
and place the machined
end in the slot under door
frame. (as shown)
1
Figure 28c.
Part No. XG0817(O) - 090109
Page 5
H(L)38VO-ST Gas Fireplace
fire feature
Installation
Notes
WARNING!
Step 5:
Do not attempt to clean glass when hot.
Ensure the tool is firmly
in the lower end of the
slot, (as shown), Then pull
toward you (Caution: hold
the tool securely).
L42DF-ST
Do not clean glass with abrasive materials as any glass etching
may cause premature glass failure.
2
Figure 28d.
Do not operate this fireplace without the glass door, or with a
broken glass door.
Installing the Glass Beads and
Optional River Rocks
Step 6:
Beads
Pull hard if necessary to
release the spring tension. (Caution: The latch
springs back with force,
hold the tool securely).
3
HL38VO-ST
This fireplace is supplied with Designer Glass beads. Remove the
Door and trim as shown in the previous Instruction. Follow these
instructions to ensure all parts are removed or replaced as required.
Once the Trim and glass doors are removed place the marbles randomly across the pan surrounding the burners as shown in Figure 29.
NOTE: DO NOT Cover burners with beads or the optional rocks, as
shown in Figure 29.
Figure 28e.
Step 7:
Remove the tool from
the latch slot. Ensure the
latches are hanging freely,
the hook end is released
from the bottom of the door.
(Repeat all 4-steps for the
remaining latches).
Note: Ensure the rocks or beads do not cover the Burners
4
Figure 28f.
Step 8:
Removing the Door:
Grasp the Door on either side, usually midway and lift upward, lift
the door carefully up and away from the front of the fireplace. See
figures 28g. Place the Door aside in a safe place while maintenance
and / or cleaning is being performed.
Figure 29. Installation of glass beads .
Optional River Rocks
The H(L)38VO-ST has the option of installing the optional cultured
rocks which mimic real stone. They are attrative yet designed to withstand a high temperature environment such as inside a gas fireplace.
These may be spaced at random, or in a visual pattern of your preference. See the Montigo web site for photographs and ideas.
www.montigo.com
Note: Ensure the rocks or beads do not cover the Burners.
Figure 28g. Removing and installing the glass doors. (Both Sides
Typical)
Installing the Door:
To install the door, hook the top edge of the door frame into place.
Lower the door into position and follow the previous steps shown in
reverse order.
Page 6
Part No. XG0817(O) - 090109
H(L)38VO-ST Gas Fireplace
fire feature
Installation
Notes
Installing the Logs and Embers
Bottom Logs
H38VO-ST
The H38VO-ST is supplied with eight (8) fibre logs. The two small
bottom logs ("A" ) are mounted on the burner grate by placing them
diagonally onto the supplied Log stands. The long Front / Back logs
("B") are placed against the grate as shown in Figure 23c. Note:
When placing logs, arrange Logs "B" as not to cover Burner holes.
Log C
Log C
Top Logs
Next are the logs "C" which are placed diagonally, as shown in
Figure 24d. The last Logs "D" are then mounted on top of logs "A" as
shown in Figure 24e.
Figure 23d. Log Installation. (Place Logs' "C" on-top of Logs "A".
Indentations on-top of Logs' "A"
Warning: If logs are not placed properly, excessive sooting will result.
Burner holes (front & back burner),
note hole pattern when placing logs
Log Stand
Air Inlets
Log Stand
Log D
Log D
Burners
Figure 23e. Completed Installation.
Front of Fireplace
Figure 23a. (Empty firebox showing the Left & Right stands).
Log A
Log A
Figure 23b. (Place Logs' "A" on Left & Right stands).
Log B
Log B
Figure 23c. (Place Logs' "B" as shown, in front of Right-hand "A",
and behind Left-hand "B".
Part No. XG0817(O) - 090109
Page 7
H(L)38VO-ST Gas Fireplace
fire feature
Operation - Model H(L)38VO-ST
H38VO-ST
HL38VO-ST
with Continuous Pilot
For Your Safety - READ BEFORE LIGHTING:
WARNING: If you do not follow these instructions exactly, a fire or
explosion may result causing property damage, person-
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
heavier than air and will settle on the floor.
What To Do If You Smell Gas:
QQ Do not try to light any appliance.
QQ Do not touch any electrical switch; do not use any phone
in your building.
QQ Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
QQ
If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualified service technician. Force
or attempt to repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system, and
any gas control which has been under water.
Lighting Instructions:
1.
2.
3.
4.
STOP! Read the safety information above on this label.
Lift out the lower Horizontal access panel.
to "OFF."
Push in gas control knob and turn clockwise
Wait five (5) minutes to clear out any gas. Smell for gas,
including near the floor. If you then smell gas, STOP! Follow
"B" in the safety information above on this label. If you don't
smell gas, go to the next step.
5. Locate pilot burner (See illustration at right.) and follow steps
below.
to "PILOT."
6. Turn knob on gas control counter clockwise
7. Push in gas control knob completely and hold. Light with Piezo
Igniter button. Continue to hold the control knob in for about
(1) minute after the pilot is lit. Release the knob and it will pop
back up. Pilot should remain lit. If it goes out repeat steps 3
through 8.
QQ If knob does not pop up when released. Stop and
immediately call your service technician or gas supplier.
QQ If the pilot will not stay lit after several tries, turn the gas
control knob to "OFF" and call your service technician
or gas supplier.
to
8. Push in gas control knob and turn counter-clockwise
"ON."
9. Replacethe lower Horizontal access
panel.
10. Turn on remote switch to ignite fire.
NOTE: Gas control knob cannot be turned from
"PILOT" to "OFF" unless knob is pushed
in slightly. Do not force.
To Turn Off Gas To Appliance:
1. Turn off remote switch.
2. Lift out the lower Horizontal access panel.
3. Push in gas control knob slightly and turn
"Off". Do not force.
clockwise to
4. Replace the lower Horizontal access panel.
Page 8
Part No. XG0817(O) - 090109
H(L)38VO-ST Gas Fireplace
fire feature
H38VO-ST-I
Operation - Model H(L)38VO-ST-I
HL38VO-ST-I
with Honeywell Electronic Ignition
For Your Safety - READ BEFORE LIGHTING:
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition system that
lights the pilot burner automatically. Do not attempt to
light the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
What To Do If You Smell Gas:
QQ Do not try to light any appliance.
QQ Do not touch any electrical switch; do not use any
phone in your building.
QQ Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
QQ If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don't try to repair it, call a qualified service technician.
Force or attempt to repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system,
and any gas control which has been under water.
Lighting Instructions:
1. STOP! Read the safety information above on this label.
2. Lift out the lower Horizontal access panel.
8. If the fireplace does not operate, follow the instructions "To
Turn Off Gas To Appliance" and call your service technician
or gas supplier.
3. Turn switch on the gas control to OFF".
4. Wait 5 minutes to clear out any gas. If you smell gas,
STOP! Follow "B" in the safety information above on this
label. If you don't smell gas, go to the next step.
5. Turn switch on the gas control to "ON". NOTE: This unit is
equipped with an ignition system that lights the pilot burner
automatically. Do not attempt to light the pilot by hand.
Gas
Inlet
Gas Control Switch
Shown in "On" Position
6. Turn on wall switch.
7. Replace the lower Horizontal access panel.
To Turn Off Gas To Appliance:
1. Turn off remote switch.
3. Turn the switch on the gas control to "Off".
2. Lift out the lower Horizontal access panel.
4. Replace the lower Horizontal access panel.
Part No. XG0817(O) - 090109
Page 9
H(L)38VO-ST Gas Fireplace
fire feature
Operation
Maintenance
Wiring
General
QQ
Gas Control and Pilot Wiring
Honeywell (Q3450)
Pilot Assembly
Have the fireplace and installation inspected yearly. The inspection
must include, but is not limited to, the following:
• A visual check of the entire vent system and termination.
• An inspection of the explosion relief flappers and the door
gasketing to ensure a proper seal.
Pilot Electrical
Harness Connector
• An inspection of the burner, venturi, and primary air openings.
• An inspection of the gas valve, gas components, and pilot flame. For your convenience a 1/8" manifold pressure tap is supplied
on the gas valve for a test gauge connection. See Figure 32.
Honeywell Gas
Control (SV9501M)
Gas Control
Connector
• Inspection of all optional equipment; fans, thermostats, etc.
Source 110V
Distribution
Panel
Wall
Switch
Water tight
Electrical box
White
Black
QQ
For Natural Gas this appliance requires a minimum inlet pressure
of 5.5" W.C. and a manifold pressure of 3.5" W.C.
QQ
For Propane Gas this appliance requires a minimum inlet pressure
of 11" W.C. and a manifold pressure of 10" W.C.
QQ
Always keep the fireplace area clear and free of combustible materials,
as well as gasoline and other flammable vapors and liquids.
QQ
Do not use this appliance if any part has been under water. Immediately
call a qualified service technician to inspect the appliance and to
replace any part of the control system and any gas control which
has been under water.
Cleaning
Figure 15. Wiring for the H(L)38VO-ST-I with Honeywell gas control and pilot.
When the fireplace is first activated, there may be some smoking and
a visible film may be left on the glass. This is a normal condition, and is
the result of burning of protective coatings on new metal.
CAUTION!
 Fireplace gas control must be in the “OFF” position and pilot
and main burners extinguished when cleaning appliance with
a vacuum.
 Doors can get very hot. Handle only when cool.
WARNING!
QQ
Glass must be cleaned periodically to remove any film (which is a
normal by-product of combustion) which may be visible. Film can
easily be removed by removing the door, as shown on page 15.
Handle the door carefully, and clean it with non-abrasive glass
cleaners. One of the most effective products is Kel Kem.
QQ
Silicone seals on inner door during initial firing will "off gas", leaving
a visual deposit of a white substance on combustion chamber walls.
This can easily be removed using normal household products.
QQ
Use a vacuum cleaner or whisk broom to keep the control
compartment, burner, and firebox free from dust and lint. QQ
Linear Burners may be cleaned periodically with a vacuum to remove
soot or other contaminates.
Do not attempt to clean glass when hot.
Do not clean glass with abrasive materials as any glass etching may cause premature glass failure.
Page 10
Part No. XG0817(O) - 090109
H(L)38VO-ST Gas Fireplace
fire feature
Maintenance
Gas Control Valve
Troubleshooting
Power
Generator
Pilot Adjustment Screw
Wall Switch
Inlet
Pressure
Manifold Pressure
Test Connection
Figure 33. Sit Nova 820 gas valve.
Pilot Burner Adjustment
1. Locate Pilot Adjustment Screw. (See figure 33.)
2. Adjust pilot screw to provide properly sized flame as shown in
figure 34).
3. After installing or servicing, leak test with a soap solution with
main burner on. Coat pipe and tubing joints, gasket etc. with soap
solution. Bubbles indicate leaks. Tighten any areas where the
bubbles appear until the bubbling stops completely.
Figure 34. Pilot Burner.
Troubleshooting
The following is a troubleshooting chart of possible problems:
PROBLEM
CORRECTIVE ACTION
Noisy Pilot Flame
Locate pilot adjustement screw on
gas control valve. Flame is decreased by
turning adjustment screw clockwise.
Pilot won’t ignite Disconnect remote wires and try to
light pilot. If pilot now works, remote
connections are faulty. Check wiring
diagram figure 33.
Main burner will
not light
1. Check wiring (see figure 33).
2. Check wall switch for proper connection.
Part No. XG0817(O) - 090109
If your fireplace still does not operate correctly, consult your dealer or
the manufacturer.
All service and repairs should be performed by a qualified
agency.
All spare parts, optional fans, and optional trim finishes are available
from your local dealer or the manufacturer.
Page 11
H(L)38VO-ST Gas Fireplace
fire feature
Warranty
The Warranty
The Companies warrants the Montigo Gas Appliance to be free from defects in materials and workmanship at the time of manufacture. On the Montigo, there is a
ten-year warranty on the firebox and its components, a five-year warranty on the main burner and pilot burner, and a one-year warranty on the gas control valve
and fibre logs. Glass, plated/painted finishes, and refractory lining are exempt.
Remedy And Exclusions
The coverage of this Warranty is limited to all components of the Gas Appliance manufactured by The Companies.
This Warranty only covers Montigo Gas Appliances installed in the United States or Canada.
If the components of the Gas Appliance covered by this Warranty are found to be defective within the time frame stated (see The Companies right of investigation
outlined below). The Companies will, at its option, replace or repair defective components of the Gas Appliance manufactured by The Companies at no charge,
and will also pay for reasonable labour costs incurred in replacing or repairing components. If repair or replacement is not commercially practical, The Companies
will, at its option, refund the purchase price of the Montigo Gas Appliance.
This Warranty covers only parts and labour as provided above. In no case shall The Companies be responsible for materials, components, or construction which
are not manufactured or supplied by The Companies, or for the labour necessary to install, repair or remove such materials, components or construction. All
replacement or repair components will be shipped F.O.B. the nearest The Companies factory.
Qualifications To The Warranty
The Gas Appliance Warranty outlined above is further subject to the following qualifications:
(1) The Gas Appliance must be installed in accordance with The Companies installation instructions and local building codes. The Warranty on this Montigo
Gas Appliance covers only the component parts manufactured by The Companies. The use of components manufactured by others with this Montigo Gas
Appliance could create serious safety hazards, may result in the denial of certification by recognized national safety agencies, and could be in violation of local
building codes. This warranty does not cover any damages occurring from the use of any components not manufactured or supplied by The Companies
(2) The Montigo Gas Appliance must be subjected to normal use. The Gas Appliances are designed to burn gas only. Burning conventional fireplace fuels such
as wood, coal or any other solid fuel will cause damage to the Gas Appliance, will produce excessive temperatures and will result in a fire hazard.
Limitations On Liability
It is expressly agreed and understood that The Companies sole obligation, and purchaser's exclusive remedy under this Warranty, under any other warranty,
expressed or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above.
In no event shall The Companies be responsible for any incidental or consequential damages caused by defects in its products, whether such damage occurs
or is discovered before or after replacement or repair, and whether or not such damage is caused by The Companies negligence. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. The duration of any implied warranty
with respect to this Montigo Gas Appliance is limited to the duration of the foregoing warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above may not apply to you.
Investigation Of Claims Against Warranty
The Companies reserves the right to investigate any and all claims against this Warranty and to decide upon method of settlement.
The Companies Are Not Responsible For Work Done Without Written Consent
The Companies shall in no event be responsible for any warranty work done without first obtaining The Companies written consent.
Dealers Have No Authority To Alter This Warranty
The Companies employees and dealers have no authority to make any warranties nor to authorize any remedies in addition to or inconsistent with those stated
above.
How To Register A Claim Against Warranty
In order for any claim under this Warranty to be valid, The Companies must be notified of the claimed defect in writing or by telephone, as soon as reasonably
possible after the defect is discovered. Claims against this Warranty in writing should include the date of installation, and a description of the defect.
Other Rights
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
NOTE:
The Companies as stated above refer to - Canadian Heating Products Inc. and/or Montigo Del Ray Corp.
Canadian Heating Products Inc. and/or Montigo DelRay Corp. reserves the right to make changes at any time, without
notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
Page 12
Part No. XG0817(O) - 090109
H(L)38VO-ST Gas Fireplace
fire feature
Appendix A - State of Massachusetts
Amendment
(Gas Fireplace / Equipment sold in the State of Massachusetts)
5.08: Modifications to NFPA-54, Chapter 10
(1) Revise NFPA-54 section 10.5.4.2 by adding a second exception as follows:
Existing chimneys shall be permitted to have their use continued when a gas conversion burner is installed, and shall be equipped with a manually reset device
that will automatically shut off the gas to the burner in the event of a sustained back-draft.
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes,
including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in
the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon
monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled
equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon
monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with
alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days
to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm
shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet
above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print
size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless,
upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the
Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes. (c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions
provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”,
the following requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for
venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
(3) After NFPA-54 section 10.10.4.2 add a new section 10.10.4.3 as follows:
When more than four gas appliances are to be vented through a common gas vent or common horizontal vent manifold, a plan of the proposed vent installation
shall be submitted to the Inspector and the serving gas supplier for review and approval.
Extraction from: Massachusets Rules and Regulations
5.00: Amendments To 2002 Edition Of ANSI Z223.1-NFPA-54
Part No. XG0817(O) - 090109
Page 13
H(L)38VO-ST Gas Fireplace
fire feature
Notes
Page 14
Part No. XG0817(O) - 090109
H(L)38VO-ST Gas Fireplace
fire feature
Notes
Part No. XG0817(O) - 090109
Page 15
fire feature
XG0211(O) - 090109
Canadian Heating Products Inc.
Montigo Del Ray Corp.
Langley, BC V4W 4A1
Ferndale, WA 98248
Download PDF