MULTIQUIP | DCA-150SSJU3 | Specifications | MULTIQUIP DCA-150SSJU3 Specifications

PARTS AND OPERATION MANUAL
PARTS AND OPERATION MANUAL
© COPYRIGHT 2001, MULTIQUIP INC.
MQ POWER
DCA-25SSIU
TM
WHISPERWATT
GENERATOR
(Standard)
PARTS LIST NO. M1870000274A
Revision #3 (09/17/01)
MULTIQUIP INC.
PARTS DEPARTMENT:
18910 WILMINGTON AVE.
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
SERVICE DEPARTMENT:
310-537-3700
800-421-1244
800-835-2551
FAX: 310-537-3927
FAX: 310-638-8046
E-mail:mq@multiquip.com • www:multiquip.com
PAGE 2 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PAR
TS DEP
AR
TMENT
ARTS
DEPAR
ARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
VICE DEP
AR
TMENT
SER
ARTMENT
SERVICE
DEPAR
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEP
AR
TMENT
DEPAR
ARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
PAGE 3 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
TABLE OF CONTENTS
Here's How To Get Help .............................................. 3
Table Of Contents ....................................................... 4
Parts Ordering Procedures ......................................... 5
Rules for Safe Operation ......................................... 6-9
Towing and Transportation ........................................ 10
Trailer Safety Guidelines ...................................... 11-15
Trailer Wiring Diagram ............................................... 16
Operation Decals ................................................. 17-18
DCA-25SSIU Specifications ..................................... 19
General Information .................................................. 20
Major Components ................................................... 21
Dimensions ............................................................... 22
Control Panel Descriptions .................................. 24-25
Engine Operating Panel Descriptions .................. 26-27
Output Terminal Panel Descriptions ..................... 28-29
Output Amerage Setup ........................................ 30-31
Output Voltage Setup ........................................... 32-35
Installation ........................................................... 36-37
Pre Setup ............................................................ 38-41
Load Application ....................................................... 42
Generator Start-up Procedure ............................. 43-45
Generator Shutdown Procedure ................................ 46
Maintenance ........................................................ 47-48
Generator Wiring Diagram ......................................... 50
Engine Wiring Diagram ............................................. 51
Engine Troubleshooting ........................................ 52-53
Generator/Engine Troubleshooting ............................ 54
Explanation of Codes in Remarks Column ............... 56
Suggested Spare Parts ............................................ 57
MQ POWER DCA-25SSIU
AC GENERATOR
Generator Assembly ............................................ 58-59
Control Box Assembly ......................................... 60-61
Engine & Radiator Assembly ............................... 62-67
Engine Operating Panel Assembly ...................... 68-69
Output Terminal Assembly ................................... 70-71
Battery Assembly ................................................ 72-73
Muffler Assembly ................................................ 74-75
Fuel Tank Assembly ............................................ 76-77
Enclosure Assembly ........................................... 78-81
Rubber Seal Assembly ........................................ 82-83
Name Plate And Decals ...................................... 84-85
ISUZU C240 ENGINE
Cylinder Head and Cover Assembly .................... 86-87
Cylinder Block Assembly .................................... 88-89
Timing Gear Assembly ........................................ 90-91
Flywheel Housing Assembly ............................... 92-93
Oil Pan Assembly ................................................ 94-95
Oil Pump Assembly ............................................ 96-97
Crankshaft, Bridge and Flywheel Assembly ........ 98-99
Oil and Fuel Filter Assembly ........................... 100-101
Oil Pipe Assembly ........................................... 102-103
Water Pump and Fan Assembly ...................... 104-105
Intake and Exhaust Manifold Assembly .......... 106-107
Air Cleaner Assembly ...................................... 108-109
Engine Foot Assembly .................................... 110-111
Injection Pump Assembly ............................... 112-113
Electrical Parts Assembly ............................... 114-115
Accessories .................................................... 116-117
Injection Pump Comp. Assembly .................... 118-121
Governor Comp. Assembly .............................. 122-127
Feed Pump Comp. Assembly .......................... 128-129
Auto Timer Assembly ...................................... 130-131
Nozzle Holder Comp. Assembly ...................... 132-133
Starter Comp. Assembly ................................. 134-135
Alternator Comp. Assembly ............................. 136-139
Terms and Conditions of Sales .............................. 140
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
PARTS ORDERING PROCEDURES
■
■
■
■
■
■
■
Dealer account number
Dealer name and address
Shipping address (if different than billing address)
Return fax number
Applicable model number
Quantity, part number and description of each part
Specify preferred method of shipment:
•
•
•
•
UPS Ground
UPS Second Day or Third Day*
UPS Next Day*
Federal Express Priority One (please provide us with your Federal
Express account number)*
•
•
Airborne Express*
Truck or parcel post
*Normally shipped the same day the order is received, if prior to 2PM west coast time.
Earn Extra Discounts when
you order by FAX!
All parts orders which include complete part numbers
and are received by fax qualify for the following extra
discounts:
Number of
line items ordered
1-9 items
Additional Discount
3%
10+ items**
5%
Get special freight allowances
when you order 10 or more
line items via FAX!**
■ UPS Ground Service at no charge for freight
■ PS Third Day Service at one-half of actual freight cost
No other allowances on freight shipped by any other carrier.
**Common nuts, bolts and washers (all items under $1.00 list price)
do not count towards the 10+ line items.
*DISCOUNTS ARE SUBJECT TO CHANGE*
ount
c
s
i
D
Fax
Extra
c USA
i
t
s
e
m
for Do
Only
s
r
e
l
Dea
UPS l
Specia
nly
ders o
xed or
For fa
Now! Direct TOLL-FREE access
to our Parts Department!
Toll-free nationwide:
800-421-1244
Toll-free FAX:
800/6-PARTS-7 • 800-672-7877
Fax order discount and UPS special programs revised June 1, 1995
PAGE 5 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
RULES FOR SAFE OPERATION
CAUTION:
Failure to follow instructions in this manual
may lead to serious injury or even death!
This equipment is to be operated by trained
and qualified personnel only! This equipment
is for industrial use only.
■ NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or generator.
The following safety guidelines should always be used when ■ High Temperatures – Allow the engine to cool before
operating the DCA-25SSIU portable generator:
adding fuel or performing service and maintenance
GENERAL SAFETY
functions. Contact with hot components can cause serious
burns.
■ DO NOT operate or service this equipment before
reading this entire manual.
■ The engine of this
generator requires an adequate
■ This equipment should not be operated by
free flow of cooling air. Never
persons under 18 years of age.
operate the generator in any
enclosed or narrow area where
free flow of the air is restricted.
■ NEVER operate this equipment without proper
If the air flow is restricted it will
protective clothing, shatterproof glasses, steelcause serious damage to the
toed boots and other protective devices
generator or engine and may
required by the job.
cause injury to people. The
generator engine gives off DEADLY carbon monoxide gas.
■ NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
CAUTION:
■ NEVER operate this equipment under the
influence or drugs or alcohol.
■ NEVER use accessories or attachments, which are not
recommended by MQ Power for this equipment. Damage
to the equipment and/or injury to user may result.
■ Manufacturer does not assume responsibility for any
accident due to equipment modifications.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ Always check the machine for loosened threads or bolts
before starting.
■ Always refuel in a well-ventilated area,
away from sparks and open flames.
■ Always use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it
to cool. DO NOT smoke around or near
the machine. Fire or explosion could
result from fuel vapors, or if fuel is spilled
on a hot engine.
■
NEVER operate the generator in an
explosive atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
■
Topping-off to filler por t is
dangerous, as it tends to spill fuel.
PAGE 6 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
RULES FOR SAFE OPERATION
CAUTION:
CAUTION:
DO NOT touch or open any of the below
mentioned components while the
generator is running. Always allow
sufficient time for the engine and generator
to cool before performing maintenance.
■ NEVER touch output terminals during operation. This is
extremely dangerous. Always stop the machine when
contact with the output terminals is required.
CAUTION:
Fluid Plugs
1. Radiator Cap - Removing the radiator cap while the
engine is hot, will result in high pressurized, boiling
water to spew out of the radiator, causing severe
scalding to any persons in the general area of the
generator.
2. Coolant Drain Plug - Removing the coolant drain
plug while the engine is hot will result in hot coolant
to flow out of the coolant drain plug, therefore causing
severe scalding to any persons in the general area
of the generator.
■ Backfeed to a utility system can cause electrocution
and/or property damage. Do not connect to any
building's electrical system except through an approved
device or after building main switch is opened.
CAUTION:
3. Engine Oil Drain Plug - Removing the engine oil
drain plug while the engine is hot will result in hot oil
to flow out of the oil drain plug, therefore causing
severe scalding to any persons in the general area
of the generator.
■ Never use damaged or worn cables when connecting
power tools or equipment to the generator. Make sure
power connecting cables are securely connected to the
generator’s output terminals, insufficient tightening of the
terminal connections may cause damage to the generator
and electrical shock.
PAGE 7 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
RULES FOR SAFE OPERATION
■ NEVER Run engine without air filter. Severe engine
damage may occur.
Battery
CAUTION:
Never over fill the battery with water above
the upper limit.
The battery contains acids that can cause injury to the eyes
and skin. To avoid eye irritation, always wear safety glasses.
Use well insulated gloves when picking up the battery. Use
the following guidelines when handling the battery:
■ Always service air cleaner frequently to prevent carburetor
malfunction.
■ Always disconnect the battery before performing service
on the generator.
■ Always be sure the operator is familiar with proper safety
precaution s and operations techniques before using
generator.
■ Always store equipment properly when not in use.
Equipment should be stored in a clean, dry location out of
the reach of children.
■ DO NOT leave the generator running in the manual mode
unattended.
■ DO NOT allow unauthorized people to operate this
equipment.
1. DO NOT drop the battery. There is the possibility of risk
that the battery may explode.
2. DO NOT expose the battery to open flames, sparks,
cigarettes etc. The battery contains combustible gases
and liquids. If these gases and liquids come in contact
with a flame or spark, an explosion could occur.
3. Always keep the battery charged. If the battery is not
charged a buildup of combustible gas will occur.
4. Always keep battery charging and booster cables in good
working condition. Repair or replace all worn cables.
5. Always recharge the battery in an open air environment,
to avoid risk of a dangerous concentration of combustible
gases.
6. In case the battery liquid (dilute sulfuric acid) comes in
contact with clothing or skin, rinse skin or clothing
immediately with plenty of water.
7. In case the battery liquid (dilute sulfuric acid) comes in
contact with your eyes, rinse eyes immediately with
plenty of water, then contact the nearest doctor or hospital,
and seek medical attention.
■ Always read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
■ Refer to the Isuzu Engine Owner's Manual for engine
technical questions or information.
Loading and Unloading (Crane)
■ Before lifting, make sure the generator's lifting hook is
secure and that there is no apparent damage to the
generator itself (loose screws, nuts and bolts). If any
part is loose or damaged, please take corrective action
before lifting.
■ Always drain fuel prior to lifting.
■ Always make sure crane or lifting device has been
properly secured to the hook of guard frame on generator.
■ NEVER lift the machine while the engine is running.
■ Use adequate lifting cable (wire or rope) of sufficient
strength.
■ When lifting the generator, always use the balanced
center-point suspension hook and lift straight upwards.
■ NEVER allow any person or animal to stand underneath
the machine while lifting.
■ When loading the generator on a truck, be sure to use
the front and back frame bars as a means to secure the
generator during transport.
PAGE 8 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
RULES FOR SAFE OPERATION
Transporting
■ Always shutdown engine before transporting.
■ Tighten fuel tank cap securely.
■ Drain fuel when transporting generator over long distances
or rough terrains.
■ Always tie-down the generator during transportation by
securing the generator.
■ If generator is mounted on a trailer, make sure trailer
complies with all local and state safety transportation
laws. See page 10 for basic towing procedures.
Emergencies
■ Always know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department.
Maintenance Safety
■ NEVER lubricate components or attempt service on a
running machine.
■ Always allow the machine a proper amount of time to
cool before servicing.
■ Keep the machinery in proper running condition.
■ Fix damage to the machine immediately and always
replace broken parts.
■ Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, coolant,
fuel, and fuel filters.
■ DO NOT use plastic containers to dispose of hazardous
waste.
■ DO NOT pour waste, oil, coolant or fuel directly onto the
ground, down a drain or into any water source.
PAGE 9 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — TOWING RULES FOR SAFE OPERATION
Towing Safety Precautions
CAUTION :
Check with your county or state safety
towing regulations department before
towing your generator.
To reduce the possibility of an accident while transporting
the generator on public roads, always make sure the trailer
(Figure 1) that supports the generator and the towing vehicle
are in good operating condition and both units are
mechanically sound.
The following list of suggestions should be used when towing
your generator:
■ Make sure the hitch and coupling of the towing vehicle
are rated equal to, or greater than the trailer "gross vehicle
weight rating" (GVWR).
■ ALWAYS inspect the hitch and coupling for wear. NEVER
tow a trailer with defective hitches, couplings, chains
etc.
■ Check the tire air pressure on both towing vehicle and
trailer. Also check the tire tread wear on both vehicles.
■ ALWAYS make sure the trailer is equipped with a "Safety
Chain".
■ ALWAYS attach trailer's safety chain to bumper of towing
vehicle.
■ ALWAYS make sure the vehicle and trailer directional,
backup, brake, and trailer lights are connected and
working properly.
■ The maximum speed unless otherwise posted for highway
towing is 55 MPH. It is not recommended for off-road
towing. However, if necessary, do not exceed 15 MPH
or less depending on type of terrain to prevent damage
to the axles.
■ Place chocked blocks underneath wheel to prevent
rolling
rolling, while parked.
■ Place support blocks underneath the trailer's bumper to
prevent tipping, while parked.
■ Use the trailer's hand winch to adjust the height of the
trailer, then insert locking pin to lock wheel stand in place,
while parked.
■ Avoid sudden stops and starts. This can cause skidding,
or jackknifing. Smooth, gradual starts and stops will
improve gas milage.
■ Avoid sharp turns to prevent rolling.
■ Remove wheel stand when transporting.
■ DO NOT transport generator with fuel in tank.
Figure 1. Generator with Trailer
PAGE 10 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — TRAILER-SAFETY GUIDELINES
CAUTION:
ALWAYS make sure the trailer is in good
operating condition. Check the tires for
proper inflation and wear. Also check the
wheel lug nuts for proper tightness.
Explanation of Chart:
This section is intended to provide the user with trailer service and maintenance information. The service and maintenance guidelines referenced in this section apply a wide range
of trailers. Remember periodic inspection of the trailer will
ensure safe towing of the equipment and will prevent damage to the equipment and personal injury.
It is the purpose of this section to cover the major maintenance components of the trailer. The following trailer components will be discussed in this section:
„
„
„
„
Tires
Lug Nut Torquing
Suspension
Electrical
Use the following definitions with reading Table 1.
1. Fuel Cell - Provides an adequate amount of fuel for the
equipment in use. Fuel cells must be empty when transporting equipment.
2. Braking System - System employed in stopping the
trailer. Typical braking systems are electric, surge, hydraulic, hydraulic-surge and air.
3. GVWR- Gross Vehicle Weight Rating (GVWR), is the
maximum number of pounds the trailer can carry, including the fuel cell (empty).
4. Frame Length - This measurement is from the ball
hitch to the rear bumper (reflector).
5.
Frame Width - This measurement is from fender to
fender.
6. Jack Stand - Trailer support device with maximum
pound requirement from the tongue of the trailer.
7. Coupler - Type of hitch used on the trailer for towing.
8. Tire Size - Indicates the diameter of the tire in inches
(10,12,14, etc.), and the width in millimeters
(175,185,205, etc.). The tire diameter must match the
diameter of the tire rim.
9. Tire Ply - The tire ply (layers) number is rated in letters;
2-ply,4-ply,6-ply, etc.
10. Wheel Hub - The wheel hub is connected to the trailer’s
axle.
11. Tire Rim - Tires mounted on a tire rim. The tire rim must
match the size of the tire.
12. Lug Nuts - Used to secure the wheel to the wheel hub.
Always use a torque wrench to tighten down the lug
nuts. See Table 4 and Figure 5 or lug nut tightening and
sequence.
13. Axle - Indicates the maximum weight the axle can support in pounds, and the diameter of the axle expressed
in inches (see Table 3). Please note that some trailers
have a double axle. This will be shown as 2-6000 lbs.,
meaning two axles with a total weight capacity of 6000
pounds.
14. Suspension - Protects the trailer chassis from shocks
transmitted through the wheels. Types of suspension
used are leaf, Q-flex, and air ride.
15. Electrical - Electrical connectors (looms) are provided
with the trailer so the brake lights and turn signals can
be connected to the towing vehicle.
16. Application - Indicates which units can be employed
on a particular trailer.
PAGE 11 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — TRAILER-SPECIFICATIONS
Table 1. Specifications
MODEL
APPLICATION
FU E L
C E LL
BRAKE
SYSTEM
GVWR
FRAME
LENGTH
FRAME
WIDTH
JACK
STAND
TRLR-10W
SDW225,
SGW250,TLW300
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-10
DCA10, TLG12,
DCA-15
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-10XF
DCA10, TLG-12,
DCA15, TLW-300
52 GAL
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-225W
WELDERS,
D A 7000S S
NO
NO
2200LB S
85"
42"
800LB .
FULL TILT WHEEL
TRLR-BLW400
BLW-400
NO
ELECTRIC
2700LB S
W/MAST 154"
W/O 124"
55"
(78" TALL)
800LB .
FULL TILT WHEEL
TRLR-50X
DCA-25
NO
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TRLR-50XF
DCA-25
41 GAL
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TRLR-70W
DCA-45, -60, 70
NO
SURGE
7000LB S
186"
77"
2000LB .
FLAT PAD
TRLR-70X
DCA-45, -60, 70
OPT
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TRLR-70XF
DCA-45, -60, 70
53 GAL
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TRLR-100XF
DCA-100, 125
150 GAL
HYDRAULIC SURGE
7000LB S
190"
76"
2000LB .
FLAT PAD
TRLR-85/125
DCA-85, 100,
125
145 GAL
HYDRAULIC
10000LB S
186"
77"
2000LB .
FLAT PAD
TRLR-150XF
DCA-150, 180
200 GAL
HYDRAULIC SURGE
11160LBS
204"
84"
5000 LB .
FLAT PAD
TRLR-220XF
DCA-220
250 GAL
HYDRAULIC SURGE
14000LB S
222"
83"
5000 LB .
FLAT PAD
TRLR-300XF
DCA-300
250 GAL
HYDRAULIC SURGE
18000LB S
238"
83"
5000 LB .
FLAT PAD
TRLR-400XF
DCA-400
350 GAL
ELECTRIC
18000LB S
238"
83"
5000 LB .
FLAT PAD
TRLR-600XF
DCA-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
TRLR-800SX
DCA-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
PAGE 12 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — TRAILER-SPECIFICATIONS
Table 1. Specifications (Con't)
MODEL
COUPLER
TIRES
WHEELS
AXLE
HUBS SUSPENSION
ELECTRICAL
TRLR-10W
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.50"
2200# 2X 2
5 LUG
3 LE A F
4 WIRE LOOM W/
4 POLE FLAT
TRLR-10
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-10XF
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-225W
2" B A LL C LA S S
2 ADJUSTABLE
175-13B
13X4.5"
2200#2X 2
5 LUG
Q F LE X
4 POLE FLAT
TRLR-BLW
400
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13 X 4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-50X
2" B A LL C LA S S
B78-13LRC
13"X4.50"
3500lbs.
2-3/8"
5 LUG
4 LE A F
4 POLE RUBBER
FLAT
TRLR-50XF
2" B A LL C LA S S
B78-13LRC
13"X4.50"
3500lbs.
2-3/8"
5 LUG
4 LE A F
4 POLE RUBBER
FLAT
TRLR-70W
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs.
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-70X
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-70XF
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs.
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-100XF
ADJUSTABLE 2-5/6
OPT 3" EYE
205-15C
BIAS (4)
14"X5.5"
3500lbs
3"
5 LUG
5 LE A F
4 WIRE LOOM
TRLR-85/125
ADJUSTABLE 2-5/6
OPT 3" EYE
ST225/75R15D
RADIAL (4)
14"x6"
(2)-6000lbs
6 LUG
7 LE A F
4 WIRE LOOM
TRLR-150XF
3" BALL EYE
750-16 E
BIAS (4)
16" X 7"
(2)-6000lbs
8 LUG
7 LE A F
4 WIRE LOOM
TRLR-220XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(4)
16" X 7"
(2)-7000lbs
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-300XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(6)
16" X 7"
(2)-6000lbs
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-400XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(6)
16" X 7"
(3)-7000lbs.
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-600XF
5TH WHEEL
ST215/75R17.5H
RADIAL (8)
16" X 7"
(3)-10000lbs
8 LUG
7 LE A F
6 WIRE LOOM
TRLR-800AR
5TH WHEEL
ST215/75R17.5H
RADIAL (8)
16" X 7"
(3)-10000lbs
8 LUG
AIR-RIDE
6 WIRE LOOM
PAGE 13 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — TRAILER SAFETY GUIDELINES
Tires/Wheels/Lug Nuts
Tires and wheels are a very important and critical
components of the trailer. When specifying or replacing the
trailer wheels it is important the wheels, tires, and axle are
properly matched.
CAUTION:
DO NOT attempt to repair or modify a
wheel. DO NOT install in inner tube to
correct a leak through the rim. If the rim
is cracked, the
air pressure in
the inner tube
may cause pieces of the rim to
explode (break off) with great force
and cause serious eye or bodily
injury.
Suspension
The leaf suspension springs and associated components
Tire Wear/Inflation
(Figure 2) should be visually inspected every 6,000 miles for
Tire inflation pressure is the most important factor in tire life.
signs of excessive wear, elongation of bolt holes, and
Pressure should be checked cold before operation. DO
loosening of fasteners. Replace all damaged parts
NOT bleed air from tires when they are hot. Check inflation
(suspension) immediately. Torqued suspension components
pressure weekly during use to insure the maximum tire life
as detailed in Table 3.
and tread wear.
Table 2 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
CAUTION:
NOTE
Figure 2. Major Suspension Components
ALWAYS wear safety glasses when removing
or installing force fitted parts. Failure to
comply may result in serious injury.
PAGE 14 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — TRAILER SAFETY GUIDELINES
Table 3. Suspension Torque Requirements
Item
Torque (Ft.-Lbs.)
3/8" U-BOLT
MIN-30 MAX-35
7/16" U-BOLT
MIN-45 MAX-60
1/2" U-BOLT
MIN-45 MAX-60
SHACKLE BOLT
SNUG FIT ONLY. PARTS MUST ROTATE FREELY.
SPRING EYE BOLT
LOCKING NUTS OR COTTER PINS ARE PROVIDED TO
RETAIN NUT-BOLT ASSEMBLY.
MIN-30 MAX-50
SHOULDER TYPE
SHACKLE BOLT
Lug Nut Torque Requirements
It is extremely important to apply and maintain proper wheel
mounting torque on the trailer. Be sure to use only the
fasteners matched to the cone angle of the wheel. Proper
procedure for attachment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
2. Torque all lug nuts in sequence. See Figure 3. DO NOT
torque the wheel lug nuts all the way down. Tighten
each lug nut in 3 separate passes as defined by Table 4.
3. After first road use, retorque all lug nuts in sequence.
Check all wheel lug nuts periodically.
Table 4. Tire Torque Requirements
Wheel Size
First Pass
FT-LBS
Second Pass
FT-LBS
Third Pass
FT-LBS
12"
20-25
35-40
50-65
13"
20-25
35-40
50-65
14"
20-25
50-60
90-120
15"
20-25
50-60
90-120
16"
20-25
50-60
90-120
Figure 3. Wheel Lug Nuts Tightening Sequence
NOTE
NEVER use an pneumatic air gun to
tighten wheel lug nuts.
PAGE 15 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — TRAILER-WIRING DIAGRAM
NOTE:
LIGHTS ARE ORIENTED FROM THE DRIVER’S SEAT
PAGE 16 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — GENERATOR DECALS
The DCA-25SSIU generator is equipped with a number of safety decals. These decals are provided for operator safety
and maintenance information. The illustration below and on the preceding pages show the decals as they appear on the
machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
PAGE 17 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — GENERATOR DECALS
PAGE 18 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — SPECIFICATIONS
Table 5. Specifications
Generator Specifications
Model
DCA-25SSIU
Type
Revolving field, self ventilated, open protected type synchronous
Armature Connection
Star with Neutral
Zig Zag
Phase
3
Single
Standby Output
26.5 KVA (21.2 KW)
15.3KW
Prime Output
25 KVA (20 KW)
14.4KW
Voltage
240V or 480V
240/120V
Frequency
60 Hz
Speed
1800 rpm
Power Factor
0.8
1
Aux. AC Power
Single Phase, 60 Hz
Voltage
120 V
Output
4.8 KW (2.4 KW x 2)
Engine Specifications
Model
Isuzu QD-6(C240)
Type
4 Cycle, water-cooled, swirl combustion chamber
No. of Cylinders
4 cylinders
Bore x Stroke
3.38 in. x 4 in. (86 mm x 102 mm)
Rated Output
30.6HP/1800 rpm
Displacement
144 cu. in. (2369cc)
Starting
Electric
Coolant Capacity
2.9 gal. (11 liters)
Lube Oil Capacity
1.45 gal. (5.5 liters)
1.65 gal. (6.3L)/hr at full load
1.3 gal. (5.0L)/hr at 3/4 load
0.9 gal. (3.4L)/hr at 1/2 load
0.6 gal. (2.3L)/hr at 1/4 load
Fuel Consumption
Battery
12V- 70AH
Fuel
#2 Diesel Fuel
PAGE 19 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — GENERAL INFORMATION
DCA-25SSIU FAMILIARIZATION
Open Delta Excitation System
Generator
The DCA-25SSIU generator is equipped with the state of
ator the art "Open-Delta" excitation system. The open delta
The MQ Power Model DCA-25SSIU is a 20 kW gener
generator
that is designed as a high quality portable (requires a trailer system consist of an electrically independent winding wound
for transport) power source for telecom sites, lighting among stationary windings of the AC output section.
facilities, power tools, submersible pumps and other There are four leads: A, B, C and D. During light loads, the
industrial and construction machinery.
power to the Automatic Voltage Regulator (AVR) is supplied
from the leads parallel connections of B&C. When loads
Engine Operating Panel
increase, the AVR switches and accepts power from leads
The “Engine Operating Panel” is provided with the following: A&D. The output of leads A&D increase proportionally with
z Tachometer
load. This of adding the voltages to each phase provides
z Water Temperature Gauge
better voltage response during heavy loads.
z Oil Pressure Gauge
The connections of the AVR to the AC output windings are
z Charging Ammeter Gauge
for sensing only. No power is required from these windings.
z Fuel level gauge
z Engine Throttle Lever
The open-delta design provides virtually unlimited excitation
z Pre-Heat Light
current, offering maximum motor starting capabilities. The
z Alarm Lights
excitation does not have a "fixed ceiling" and responds
z Panel Light
according the demands of the required load.
z Panel Light Switch
z Starter Switch
Engine
Generator Control Panel
The “Generator Control Panel” is provided with the following:
z Output Voltage Adjustment Knob
z Frequency Meter (Hz)
z AC Ammeter (Amps)
z AC Voltmeter (Volts)
z Ammeter Change-Over Switch
z Voltmeter Change-Over Switch
z Main Circuit Breaker 60 amps
z Over-Current Relay
The DCA-25SSIU is powered by a 4 cycle, water cooled,
turbocharged Isuzu QD60(C640) diesel engine. This engine
is designed to meet every performance requirement for the
generator. Reference Table 5, page 19 for engine
specifications.
In keeping with MQ Power’s policy of constantly improving
its products, the specifications quoted herein are subject to
change without prior notice.
The basic controls and indicators for the DCA-25SSIU
generator are addressed on the following pages.
Output Terminal Panel
The “Output Terminal Panel” is provided with the following:
z
z
z
z
Three 120V output receptacles, 50 amp
Two 120V output receptacles, 20 amp
3 Circuit Breakers 240V @65 amps
2 GFCI Circuit Breakers 120V@ 20amps
Mechanical Governor System
The mechanical governor system control the RPM of the
engine. When the engine demands increase or decrease,
the mechanical governor system regulates the frequency
to ±5%. The electronic governor option limits frequency
fluctuation to ±0.25%.
PAGE 20 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — MAJOR COMPONENTS
Figure 4. Major Components
PAGE 21 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — DIMENSIONS (TOP, SIDE AND FRONT)
Figure 5. Dimensions
PAGE 22 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
NOTE PAGE
PAGE 23 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — CONTROL PANEL
Figure 6. Control Panel
PAGE 24 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — CONTROL PANEL
The definitions below describe the controls and functions of
the DCA-25SSIU " Control Panel " (Figure 6).
1.
Main Circuit Breaker – This three-pole, 60 Amp main
breaker is provided to protect the UNV voltage output
terminals from overload.
2.
Frequency Meter – Indicates the output frequency in
hertz (Hz). Normally 63 Hz ±0.5 Hz .
3.
AC Ammeter – Indicates the amount of current the
load is drawing from the generator.
4.
AC Voltmeter – Indicates the output voltage present
at the UVW or output terminals.
Voltage Regulator Control – Allows manual
adjustment of the generator’s output voltage.
5.
6.
Ammeter Change-Over Switch – This switch allows
the AC ammeter to indicate the current flowing to the
load connected to any phase of the output terminals, or
to be switched off.
7.
Voltmeter Change-Over Switch – This switch allows
the AC voltmeter to indicate phase to phase voltage
between any two phases of the output terminals or to
be switched off.
PAGE 25 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — ENGINE OPERATING PANEL
Figure 7. Engine Operating Panel
PAGE 26 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — ENGINE OPERATING PANEL
The definitions below describe the controls and functions of
the DCA-25SSIU " Engine Operating Panel " (Figure 7).
1.
Panel light - Normally used in dark places or at night.
When activated, panel will luminate. When the generator
is not in use, turn the panel light switch to the ‘OFF’
position.
2.
Oil Pressure Lamp - This light will luminate if the oil
pressure exceeds 15 psi and will shut off the engine.
3.
Water Temperature Lamp - This light will luminate if
the water temperature exceeds 215oF and will shut off
the engine.
4.
Panel light switch- When activated, will turn on control
panel light.
5.
Pre-Heat Indicator - This light will luminate once the
engine is warmed to an operating temperature.
6.
Ignition Switch - This switch is used with a key to
start, preheat, and stop the engine..
7.
Engine Throttle Lever - To change the speed of the
engine from idle to high, pull and turn the handle.
Tachometer – Indicates engine speed in RPM’s for 60
Hz operation. This meter should indicate 1800 RPM’s
when the rated load is applied. In addition a built in hour
meter will record the number of operational hours that
the generator has been in use.
8.
9. Fuel Gauge - Indicates amount of diesel fuel available
10. Charging Ammeter Gauge – Indicates the current
being supplied by the engine’s alternator which provides
current for generator’s control circuits and battery
charging system.
11. Water Temperature Gauge – During normal operation
this gauge be should read between 165o to 203oF.
12. Oil Pressure Gauge – Normal operation should be about
42~71 psi. When starting the generator the oil pressure
may read a bit higher, but after the engine warms up
the oil pressure should return to normal.
PAGE 27 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — OUTPUT TERMINAL PANEL
Output Terminal Panel
The output control panel is located on the rear (control panel)
end of the generator. The UVW lugs are protected by a face
plate cover that can be secured in the close position by a
pad lock.
Connecting Load
Loads can be connected to the generator by the UVW Lugs or
the duplex receptacle. (See Figure 9). Make sure to read the
operation manual before attempting to connect a load to the
generator.
120 Volt Receptacle
One GFCI Duplex NEMA 5-20R (120V, 20 Amp) receptacle
is located on the output terminal. This receptacle can be
used anytime the generator is in operation. The receptacle
is controlled by the circuit breaker located on the control
panel.
The reset button will reset the receptacle after being tripped.
Pressing the "Test Button" (See Figure 8) in the center of
this receptacle will check the GFCI function. The receptacle
should be tested at least once a month.
Figure 9. Connecting Loads
Circuit Breakers
To protect the generator from an overload, a 3-pole, 60 amp,
main circuit breaker is provided to protect the UVWO output
terminals from overload. In addition two single-pole, 20 amp
GFCI circuit breakers are provided to protect the GFCI
receptacles from overload. Three 50 amp circuit breakers
have also been provided to protect the load side of the
generator from overload. Make sure to switch ALL circuit
breakers to the "OFF" position prior to starting the engine.
Figure 8. GFCI Test Button
Maximum Output
The entire load connected to the UVW l ugs and all four slots in
the duplex receptacle must not exceed 22 kW in standby or 20
kW in prime output.
120V Receptacles - These receptacles can be used
anytime the generator is in operation. They are controlled
by the circuit breakers above them.
Twist Lock Dual Voltage Receptacles - To use these
receptacles, place the voltage selector switch in the single
phase 240/120 voltage position and adjust the output
voltage to 240 volts with the voltage regulator on the
control panel (see Figure 6, page 24). Place the voltmeter
change-over switch to the U-W position and the ammeter
change-over switch to the U or W to read the output.
PAGE 28 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — OUTPUT TERMINAL PANEL
NOTE
Legs “O” and Ground are
considered Bonded Grounds.
Figure 10. Output Terminal Description
PAGE 29 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — OUTPUT AMPERAGE SETUP
Output Terminal Panel Available Voltages
A wide range of voltages are available to supply load to
many different applications. Voltages may be selected by
using the voltage selector switch and depending how you
hookup your hard wire connection to the generator. To
obtain voltages listed, fine adjustment with the voltage
regulator on the control panel is necessary. See the table
below (Table 6) for a list of available voltages the generator
is able to supply.
Over Current Relay
An over current relay is connected to the circuit breaker.
During an over current situation, both the circuit breaker
and the over current relay may trip. If the circuit breaker
can not be reset, the reset button on the over current relay
must be pressed. The over current relay is located inside
the control box.
Table 6. Voltage Available
3 P h ase
(Sw itchable)
208 VOLT
220 VOLT
240 VOLT
416 VOLT
440 VOLT
480 VOLT
Single Phase
(Sw itchable)
120 VOLT
127 VOLT
139 VOLT
240 VOLT
254 VOLT
277 VOLT
CAUTION :
NEVER switch the voltage selector switch
position while the engine is engaged.
Voltage Selector Switch Locking Button
The voltage selector switch has a locking button to protect
the generator and generator load from being switched while
the engine is running. To lock the voltage selector switch,
press in the red button located on the lower part of the
voltage selector switch, and use a pad lock to hold it into
this position.
Maximum Amps
The following table show the maximum amps the entire
generator can provide. Do not exceed the maximum amps
listed. (See Table 7)
Table 7. Maximum Amps
Rated Voltage
Maximum Amps
Single Phase
120 Volt
55.5 amps (4 wire)
Single Phase
240 Volt
27.8 amps (4 wire)
Three Phase
240 Volt
60 amps
Three Phase
480 Volt
30 amps
PAGE 30 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — OUTPUT AMPERAGE SETUP
Receptacle Use
When the UVWO terminals are providing power, the
receptacle power available decrease. Do not exceed
receptacle power available listed on Table 8.
Table 8. Receptacle Use
Power in Use
Receptacle
Power
Available
240/480V
3-Phase
240/120V
Single Phase
or Twist Lock
CS6369
Duplex NEMA
5-20R 120V
25
14.4
0
20.8
13.2
1.2
16.7
12
2.4
12.5
10.8
3.6
8.4
9.6
4.8
Figure 11. Voltage Selector Switch 240/120V
Single Phase Position
Figure 12. AC Voltmeter
Change-over switch
(Reading the W-U leg on
the output terminal panel)
Figure 13. AC Voltmeter
Gauge
(Volt reading on W-U Lug)
How To Read The Output Terminal Gauges
The gauges (Figures 13 and 15) and change-over switches
on the control panel DO NOT effect the generator output.
They are to help observe how much power is being
supplied produced at the UVWO legs.
When the voltage selector switch is in the 240/120V
position (see Figure 11), place the AC voltmeter changeover switch to the W-U position (Figure 12) and the AC
ammeter change-over switch to the U or W position (Figure
14) to read the output on the selected leg.
Figure 14. AC Ammeter
Change-over Switch
(Reading the U leg on the
output terminal panel)
Figure 15. AC Ammeter
(Amp reading on U lug)
NOTE
When using plural single phase
voltages, make sure to balance
the load on each of the single
phase legs.
PAGE 31 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — OUTPUT VOLTAGE SETUP
240/120V Hard Wire Hookup
480/240V Hard Wire Hookup
With the voltage selector set and locked at ‘single phase
240/120’ and using single phase 120 volts, it will provide
three legs available with 100 amps each on three different
circuits (Figure 16).
When using single phase 240 volts, it will provide one leg
with 50 amps available (Figure 16).
With the voltage selector set and locked at ‘3 phase 480/
277’ (Figure 17) and using the 3-phase 240 volt hookup, it
will provide one circuit available at 108 amps with any two
wires plus the ground (Figure 18).
When using the 3-phase 480 volts hookup, it will provide
one circuit available at 50 amps available with all three wires
plus ground (Figure 18).
FIGURE 17. Voltage Selector Switch 480/277V Three Phase
Position
FIGURE 16. Hard Wire Hookup at 240/120V Position
FIGURE 18. Hard Wire Hookup For 240V or 480V
PAGE 32 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — OUTPUT VOLTAGE SETUP
Voltage Selector Switch- 3 Phase 480/277V Position
The following are additional voltages available when the
voltage selector switch is in the 3 phase 480/277V
position.
Single Phase: 480V, 440V, or 416 Volt
This setting can provide single phase power at 480, 440,
or 416 volts. After hooking up the hard wires to the lugs
as shown in Figure 21, 480 volts can be obtained the
voltage regulator knob turned toward maximum; 440 volts
can be obtained with the voltage regulator knob is turned
down; and 416 volts can be obtained with the voltage
regulator knob is at lowest setting.
Figure 19. Voltage Regulator Knob
3 Phase, 480V, 440V, or 416 Volt
This setting can provide 3-phase power at 480, 440, or
416 volts. After hooking up the hard wires to the lugs as
shown in Figure 20, 480 volts can be obtained the
voltage regulator knob turned toward maximum; 440 volts
can be obtained with the voltage regulator knob is turned
down; and 416 volts can be obtained with the voltage
regulator knob is at lowest setting.
Figure 20. Hard Wire Hookup for Three Phase
480V, 440V, or 416V
Figure 21. Hard Wire Hookup for Single Phase 480V, 440V,
or 416V
Single Phase: 277V, 254V, or 240V
This setting can provide single phase power at 277, 254
or 240 volts. After hooking up the hard wires to the lugs
as shown in Figure 22, 277 volts can be obtained the
voltage regulator knob turned toward maximum; 254 volts
can be obtained with the voltage regulator knob is turned
down; and 240 volts can be obtained with the voltage
regulator knob is at lowest setting.
Figure 22. Hard Wire Hookup for Single Phase 277V, 254V,
or 240V
PAGE 33 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — OUTPUT VOLTAGE SETUP
Voltage Selector Switch- 3 Phase 240/139V Position
The following are additional voltages available when the
voltage selector switch is in the 3 phase 240/139V
position.
FIGURE 23. Voltage Selector Switch 240/139V Three Phase
Position
3 Phase, 240V, 220V, or 208 Volt
This setting can provide 3-phase power at 240, 220, or
208 volts. After hooking up the hard wires to the lugs as
shown in Figure 24, 240 volts can be obtained the
voltage regulator knob turned toward maximum; 220 volts
can be obtained with the voltage regulator knob is turned
down; and 208 volts can be obtained with the voltage
regulator knob is at lowest setting.
Figure 24. Hard Wire Hookup for Three Phase 240V, 220V, or
208V
Single Phase: 240V, 220V, or 208 Volt
This setting can provide single phase power at 240, 220,
or 208 volts. After hooking up the hard wires to the lugs
as shown in Figure 25, 240 volts can be obtained the
voltage regulator knob turned toward maximum; 220 volts
can be obtained with the voltage regulator knob is turned
down; and 208 volts can be obtained with the voltage
regulator knob is at lowest setting.
Figure 25. Hard Wire Hookup for Single Phase 240V, 220V,
or 208V
Single Phase: 139V, 127V, or 120V
This setting can provide single phase power at 139, 127,
or 120 volts. After hooking up the hard wires to the lugs
as shown in Figure 26, 139 volts can be obtained the
voltage regulator knob turned toward maximum; 127 volts
can be obtained with the voltage regulator knob is turned
down; and 120 volts can be obtained with the voltage
regulator knob is at lowest setting.
Figure 26. Hard Wire Hookup for Single Phase 139V, 127V,
or 120V
PAGE 34 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — OUTPUT VOLTAGE SETUP
Voltage Selector Switch- Single Phase 240/120V
Position
The following are additional voltages available when the
240/120V position.
Single Phase: 120 Volt
This setting can provide single phase power at 120 volts.
After hooking up the hard wires to the lugs as shown in
Figure 29, 120 volts can be obtained by using the voltage
regulator to fine tune.
Figure 29. Hard Wire Hookup for Single Phase, 120 volt
Figure 27. Voltage Selector Switch 240/120V Single Phase
Position
Single Phase, 240 Volt
This setting can provide single phase power at 240 volts.
After hooking up the hard wires to the lugs as shown in
Figure 28, 240 volts can be obtained and using the
voltage regulator to fine tune.
Figure 28. Hard Wire Hookup for Single Phase 240 volt
PAGE 35 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — INSTALLATION
Outdoor Installation
Install the generator in a location where it will not be exposed
to rain or sunshine. Make sure the generator is on secure
level ground so that it cannot slide or shift around. Also
install the generator in a manner so that the exhaust will not
be discharged in the direction of nearby homes.
The installation site must be relatively free from moisture
and dust. All electrical equipment should be protected from
excessive moisture. Failure to do will result in deterioration
of the insulation and will result in short circuits and grounding.
CAUTION :
An electric shock may happen when
vibrators are used. Pay close attention to
handling when operating vibrators and
always use rubber boots and gloves to
insulate the body from electrical shock.
Generator Grounding
To guard against electrical shock and possible damage to
the equipment, it is important to provide a good EARTH
ground.
Foreign materials such as dust, sand, lint and abrasive
materials have a tendency to cause excessive wear to
engine and alternator parts.
Article 250 (Grounding) of the National Electrical Code (NEC)
provides guide lines for proper grounding and specifies that
the cable ground shall be connected to the grounding system
of the building as close to the point of cable entry as
practical.
CAUTION :
NEC articles 250-64(b) and 250-66 set the following
grounding requirements:
Pay close attention to ventilation when
operating the generator inside tunnels and
caves. The engine exhaust contains
noxious elements. Engine exhaust must
be routed to a ventilated area.
Indoor Installation
Exhaust gases from diesel engines are extremely poisonous.
Whenever an engine is installed indoors the exhaust fumes
must be vented to the outside. The engine should be installed
at least two feet from any outside wall. Using an exhaust
pipe which is too long or too small can cause excessive
back pressure which will cause the engine to heat
excessively and possibly burn the valves.
Mounting
The generator must be mounted on a solid foundation (such
as concrete) and set firmly on the foundation to isolate
vibration of the generator when it is running. The generator
must set at least 6 inches above the floor or grade level (in
accordance to NFPA 110, Chapter 5-4.1). DO NOT remove
the metal skids on the bottom of the generator. They are to
resist damage to the bottom of the generator and to maintain
alignment.
1. Use one of the following wire types to connect the
generator to earth ground.
a. Copper - 10 AWG (5.3 mm2) or larger.
b. Aluminum - 8 AWG (8.4 mm2) or larger.
2. When grounding the generator (Figure 30) connect the
ground cable between the lock washer and the nut on
the generator and tighten the nut fully. Connect the other
end of the ground cable to earth ground.
3. NEC article 250-52(c) specifies that the earth ground
rod should be buried a minimum of 8 ft. into the ground.
NOTE
When connecting the generator to any buildings
electrical system ALWAYS consult with a licensed
electrician.
PAGE 36 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — INSTALLATION
Figure 30.
Typical Generator Grounding Application
PAGE 37 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — PRE-SETUP
General Inspection Prior to Operation
Circuit Breakers
The DCA-25SSIU generator has been thoroughly inspected
and accepted prior to shipment from the factory. However,
be sure to check for damaged parts or components, or loose
nuts and bolts, which could have occurred in transit.
Extension Cable
To protect the generator from an overload, a 3-pole, 60 amp,
main circuit breaker is provided to protect the UVW output
terminals from overload. In addition two single-pole, 20 amp
GFCI circuit breakers are provided to protect the GFCI
receptacles from overload. Three 50 amp load circuit breakers
have also been provided to protect the load side of the
When electric power is to be provided to various tools or generator from overload. Make sure to switch ALL circuit
loads at some distance from the generator, extension breakers to the "OFF" position prior to starting the engine.
cords are normally used. Cables should be sized to allow
for distance in length and amperage so that the voltage
drop between the generator and point of use (load) is held
to a minimum. Use the Cable Selection Guide (Table 9)
as a guide for selecting proper cable size.
NOTE
ALWAYS consult with a licensed
electrician for correct extension
cord wire size.
Table 9. Cable Selection (60 Hz, Single Phase Operation)
Load In Watts
Current in
Amperes At 120 At 240
Volts
Volts
Maximum Allowable Cable Length
#10 Wire
#12 Wire
#14 Wire
#16 Wire
2.5
300
600
1000 ft.
600 ft.
375 ft.
250 ft.
5
600
1200
500 ft.
300 ft.
200 ft.
125 ft.
7.5
900
1800
350 ft.
200 ft.
125 ft.
100 ft.
10
1200
2400
250 ft.
150 ft.
100 ft.
15
1800
3600
150 ft.
100 ft.
65 ft.
20
2400
4800
125 ft.
75 ft.
50 ft.
CAUTION: Equipment damage can result from low voltage.
PAGE 38 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — PRE-SETUP
Lubrication Oil
Fuel
Fill the engine crankcase with lubricating oil through the filler
hole, but do not overfill. Make sure the generator is level.
With the dipstick inserted all the way, verify that the oil level
is maintained between the two notches (Figure 31) on the
dipstick. See Table 10 for proper selection of engine oil. Use
only CC grade or higher.
Fill the fuel tank with clean and fresh diesel fuel. DO NOT
fill the tank beyond capacity.
Pay attention to the fuel tank capacity when replenishing
fuel. Refer to the fuel tank capacity listed on page 19
Specification Table 5.
The fuel tank cap must be closed tightly after filling. Handle
fuel in a safety container. If the container does not have a
spout, use a funnel. Wipe up any spilled fuel immediately.
CAUTION :
Never fill the fuel tank while the engine is
running or in the dark. Gasoline spillage
on a hot engine can cause a fire or
explosion. If gasoline spillage occurs, wipe
up the spilled gasoline completely to
prevent fire hazards.
Coolant
Figure 31. Engine Oil Dipstick
Use only drinkable tap water. If hard water or water with
many impurities is used, the inside of the engine and radiator
may become coated with deposits and cooling efficiency
will be reduced. See maintenance section on page 42 and
43 on instructions to flush out radiator.
When checking the engine oil, be sure to check if the oil is
clean and viscous. If the oil is not clean, drain the oil by An anticorrosion additive added to the water will help prevent
removing the oil drain plug, and refill with the specified amount deposits and corrosion in the cooling system.
of oil as outlined in the Isuzu Engine Operator’s Manual.
Table 10. Recommended Motor Oil
Ambient Temperature
Range
Type Oil
-30o~0oC (-22o~32oF)
SAE 10W or SAE10W-30
0o~25oC (32o~77oF)
SAE 30 or SAE15w-40W, 20W-40
Above 25oC (86oF)
SAE 40
PAGE 39 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — PRE-SETUP
CAUTION :
When adding coolant or antifreeze to the
radiator, do not remove the radiator cap
until the unit has completely cooled.
Day-to-day addition of coolant is done from the reserve tank.
When adding coolant to the radiator, DO NOT remove the
radiator cap until the unit has completely cooled. See Table11.
for engine, radiator, and reserve tank coolant capacities. Make
sure the coolant level in the reserve tank is always between
the "H" and the "L" markings.
Table 11. Coolant Capacity
Engine and Radiator
2.9 Gal. (11 Liters)
Reserve Tank
0.27 Gal. (1 Liter)
Cleaning the Outer Radiator
The engine may overheat if the radiator fins become
overloaded with dust or debris. Periodically clean the radiator
fins with compressed air. Cleaning inside the radiator is
dangerous, so clean only with the engine turned off and the
battery disconnected.
Air Cleaner
Periodic cleaning/replacement is necessary. Inspect it in
accordance with the Kubota Engine Owner's Manual.
Fan Belt Tension
A slack fan belt may contribute to overheating, or to
insufficient charging of the battery. Inspect the fan belt for
damage and wear and adjust it in accordance with the Kubota
Engine Owner's Manual.
The fan belt tension is proper if the fan belt bends 10 to 15
mm (Figure 32) when depressed with the thumb as shown
below. Never place hands near the belts or fan while the
generator is running.
Operation in Freezing Weather
When operating in freezing weather, be certain the proper
amount of antifreeze (Table 12) has been added.
Table 12. Anti-Freeze Operating Temperatures
Figure 32. Fan Belt Tension
Freezing Point
Boiling Point
°C
°F
°C
°F
40
-24
-12
106
222
50
-37
-34
108
226
Vol %
Anti-Freeze
NOTE
When the antifreeze is mixed with
w ater
atio m
ust
ater,, the antifreez
antifreezee mixing rratio
must
be less than 50%.
CAUTION :
Never place hands near the belts or fan
while the generator set is running.
Adjusting Fan Belt
If the fan belt does not have the 10 to 15mm defection
follow the procedure below to adjust:
y Loosen the alternator adjusting plate and alternator
mounding bolt.
y Pivot the alternator at the mounting bolt toward the engine
left or right until the belt reflects the proper tension.
y Tighten the mounting bolt and the adjusting bolt.
PAGE 40 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — PRE-SETUP
Battery
This unit is of negative ground. DO NOT connect in reverse.
Always maintain battery fluid level between the specified
marks. Battery life will be shortened, if the fluid level is not
properly maintained. Add only distilled water when
replenishment is necessary. DO NOT over fill.
The battery is sufficiently charged if the specific gravity of
the battery fluid is 1.28 (at 68° F). If the specific gravity
should fall to 1.245 or lower, it indicates that the battery is
dead and needs to be recharged or replaced.
Check to see whether the battery cables are loose. Poor
contact may result in poor starting or malfunctions. Always
keep the terminals firmly tightened. Coating the terminals
with a thin film of grease will help to inhibit corrosion.
Battery Cable Installation
ALWAYS be sure the battery cables (Figure 33) are properly
connected to the battery terminals as shown below. The RED
cable is connected to the positive terminal of the battery,
and the BLACK cable is connected to the negative terminal
of the battery.
CAUTION :
If the battery cable is connected
incorrectly, damage to the generator will
occur. Pay close attention to the polarity
of the battery when connecting the
battery.
When connecting battery do the following:
1. DO NOT connect the battery cables to the battery
terminals when the key is in the ignition and is set in
'START' mode. ALWAYS remove the key from the
ignition and the ignition switch is in the OFF position
when connecting the battery.
2. Place a small amount of grease around both battery
terminals. This will ensure a good connection and will
help prevent corrosion around the battery terminals.
CAUTION :
Inadequate battery connections may
cause poor starting of the generator, and
create other malfunctions.
Wiring
Inspect the entire generator for bad or worn electrical wiring
or connections. If any wiring or connections are exposed
(insulation missing) replace wiring immediately.
Piping and Hose Connection
Inspect all piping, oil hose, and fuel hose connections for
wear and tightness. Tighten all hose clamps and check hoses
for leaks.
Figure 33. Battery Connections
If any hose (fuel or oil) lines are defective replace them
immediately.
PAGE 41 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — LOAD APPLICATION
Single Phase Load
CAUTION:
Always be sure to check the nameplate on the generator
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generator for operating the equipment.
Motors and motor-driven equipment draw
much greater current for starting than
during operation.
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
An inadequate size connecting cable which cannot carry
the required load can cause a voltage drop which can burn
out the appliance or tool and overheat the cable.
When the voltage selector switch is in single phase (240/
120V position), place the AC voltmeter change-over switch
to the U-W position and the AC ammeter change over-switch
to the U or W position to read the output.
NOTE
If wattage is not given on the
equipment's name plate, approximate
wattage may be determined by
multiplying nameplate voltage by the
nameplate amperage.
WATTS = VOLTAGE x AMPERAGE
The power factor of this generator is 1.0. See Table 13.
below when connecting loads.
Table 13. Power Factor By Load
Type Of Load
Power Factor
Single-phase induction motors
0.4 - 0.75
Electric heaters, incandescent
lamps
1.0
Fluorescent lamps, mercury lamps
0.4 - 0.9
Electronic devices, communication
equipment
1.0
Common power tools
0.8
Three Phase Load
When calculating the power requirements for 3-phase power
use the following equation:
z When connecting a resistance load such as an
incandescent lamp or electric heater, a capacity of up
to the generating set’s rated output (kW) can be used.
z When connecting a fluorescent or mercury lamp, a
capacity of up to the generating set’s rated output (kW)
multiplied by 0.6 can be used.
z When connecting an electric drill or other power tools,
pay close attention to the required starting current
capacity.
If wattage is not available on the equipment, approximate
wattage may be determined by multiplying the nameplate
voltage by the nameplate amperage for three-phase:
WATTS =1.732 x VOLTAGE x AMPERAGE
CAUTION:
Before connecting this generator to any
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch. Serious injury or death
may result without this transfer switch.
NOTE
If output (kVA) is not given
on the equipment nameplate,
approximate output may be
determined by multiplying voltage by
amperage by
and 1.732.
PAGE 42 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — GENERATOR START-UP PROCEDURE
WARNING:
The engine's exhaust contains harmful
W AY S ventilate the
emissions. A LLW
exhaust when operating inside tunnels,
excavations or buildings. Direct exhaust
away from nearby personnel.
2. Connect the load to the UVW terminals as shown in
Figure 35. These terminals can be found on the output
terminal panel, (see page 29 Figure10). To gain access
to the output terminals lift the UVW cover. Tighten
terminal nuts securely to prevent load wires from slipping
out.
Before Starting
Engine
1. Check the lubricating oil level prior to starting the engine.
Make sure the generator is level. The oil level must be
maintained between two notches on the dipstick.
2. When there is not enough lubricating oil, fill the crankcase
with high grade motor oil. Use a high quality detergent
oil classified CC or higher (See Table 8 on page 33).
3. Check the coolant level in the radiator and subtank.
Replenish with antifreeze as necessary. Always maintain
the coolant level between the FULL and LOW markings
on the coolant container. Be sure that the radiator cap is
fastened securely.
4. Check the fuel level on the fuel gauge. If fuel is low, fill
the fuel tank with clean fresh unleaded automotive diesel.
If diesel spillage occurs, completely wipe up the spilled
fuel immediately.
Figure 35. UVW Terminal Lugs (Load)
3. Connect the negative battery cable (BLACK) to the
negative post on the battery (Figure 36).
Before Starting
Generator and Control Panel
CAUTION:
NEVER start the engine with the
main, GFCI or load circuit breakers
in the ON position.
1. Be sure to disconnect the electrical load and switch the
main, load and G.F
.C
.I. circuit breakers (Figure 34) to
G.F.C
.C.I.
the “OFF” position prior to starting the engine.
IVE
ST
PO
E
TIV
GA
NE
RY
E
TT
A
B
Figure 36. Battery Connections
Figure 34. Main, GFCI and
Load Circuit Breakers
PAGE 43 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — GENERATOR START-UP PROCEDURE
4. Close all engine enclosure doors (Figure 37).
8. Once the preheat indicator lights, turn the ignition
key to ‘START’ until the engine starts (Figure 41).
Then release the key to ‘RUN’.
Figure 41. Ignition Switch ‘START’
Figure 37. Engine Enclosure Doors
5. Check the voltage selection switch (Figure 38) is at
the desired voltage.
9. Pull the engine throttle and turn to the right until the
metal stop rests against the control panel (Figure 42).
Figure 42. Engine Throttle Lever (high)
Figure 38. Voltage Selection Switch
10. The generator's frequency meter (Figure 43) displays
the 60 cycle output frequency in HERTZ.
6. Make sure the engine throttle (Figure 39) is in
’start/idle’.
Figure 39. Engine Throttle Lever (low)
7. Turn the ignition key to preheat (Figure 40), until the
preheat indicator turns on.
Figure 43. Frequency Meter (Hz)
11. The generator's voltage meter (Figure 44) displays the
120 VAC in VOLTS. If the voltage is not within the
specified frequency tolerance, use the voltage
adjustment control knob (Figure 45) to increase or
decrease the desired voltage.
Figure 40. Ignition Switch ‘PREHEAT’
Figure 44. Voltage Meter (Volts)
PAGE 44 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — GENERATOR START-UP PROCEDURE
15. The charging ammeter will dindicate if the battery is being
properly charged or if the any current is being charged
properly.
Figure 45. Voltage Adjust Control Knob
12. The ammeter (Figure 46) will indicate zero amps with no
load applied. When a load is applied, this meter will
indicate the amount of current that the load is drawing
from the generator’s alternator.
20
40
0
60
Figure 49. Charging Ammeter
16. The tachometer (Figure 50) will indicate the speed of
the engine when the generator is operating. Under normal
operating conditions this speed is approximately 1800
RPM’s.
75
A
Figure 46. Ammeter (No Load)
13. The engine oil pressure gauge (Figure 47) will indicate
the oil pressure (kg/ cm2) of the engine. Under normal
operating conditions the oil pressure is approximately
25 psi.
Figure 50. Engine Tachometer
17. Turn the MAIN, GFCI and LOAD circuit breakers to
their ON position (Figure 51).
Figure 47. Oil Pressure Gauge
14. The coolant temperature gauge (Figure 48) will indicate
the coolant temperature. Under normal operating
conditions the coolant temperature is between 165 and
215 degrees Fahrenheit.
WATER
Figure 51. Main and GFCI Circuit Breakers
TEMP
Figure 48. Coolant Temperature Gauge
PAGE 45 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — GENERATOR SHUTDOWN PROCEDURE
18. Observe the generator's ammeter (Figure 52) and verify ENGINE SHUTDOWN
it reads the anticipated amount of current with respect To shutdown the generator, use the following procedure:
to the load. The ammeter will only display a current
reading if the load is in use.
1. Switch both the MAIN, GFCI and LOAD circuit breakers
(Figure 53) to the “OFF” position.
40
20
60
0
75
A
Figure 52. Ammeter (Load)
Figure 53. Main, GFCI and Load
circuit breakers
19. The generator will run until manually stopped or an
abnormal condition occurs.
2.
Set the engine throttle lever to (low) position.
3. Let the engine cool by running it for 3-5 minutes with no
load applied.
4. Turn the ignition key to ‘STOP’ (Figure 54).
Figure 54. Ignition Switch ‘STOP’
5.
Remove the load from the UVW terminal strip.
PAGE 46 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
NOTE PAGE
PAGE 47 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — MAINTENANCE
General Inspection
Check Oil Level
Prior to each use, the generator should be cleaned and
inspected for deficiencies. Check for loose, missing or
damaged nuts, bolts or other fasteners. Also check for fuel,
oil, and coolant leaks.
Check the crankcase oil level prior to each use, or when
the fuel tank is filled. Insufficient oil may cause severe
damage to the engine. Make sure the generator is level.
The oil level must be between the two notches on the dipstick
as shown in Figure 31, page 39.
Replacing Oil Filter
Engine Side (Refer to the Engine Instruction Manual)
Air Cleaner
Every 50 hours: Remove air cleaner element and clean heavy
duty paper element with kerosene, or foam element with
liquid detergent and hot water. Wrap foam element in a cloth
and squeeze dry. For heavy duty paper element, wipe
excess kerosene with towel.
Detach the oil filter cartridge with a filter wrench.
Fuel Addition
After the oil cartridge has been replaced, the engine oil
will drop slightly. Run the engine for a while and check
for leaks before adding more oil if needed. Clean
excessive oil from engine.
Add diesel fuel (the grade may vary according to season
and locations). Always pour through the mesh filter.
Removing Water from the Fuel Tank
After prolonged use, water and other impurities accumulate
in the bottom of the tank. Occasionally remove the drain
cock and drain the contents. During cold weather, the more
empty volume inside the tank, the easier it is for water to
condense. This can be reduced by keeping the tank full as
much as possible.
Apply a film of oil to the gasket for the cartridge.
Screw in the cartridge by hand. When the gasket is in
contact with the seal surface, tighten the cartridge one
or two more times by hand.
Replacing Fuel Filter
Replace the fuel filter cartridge with new one every 400
hours or so.
Apply fuel oil thinly over the gasket and hand-tighten
the cartridge into position.
Vent any air.
Flushing Out Radiator and Replacing Coolant
Air Removal
If air enters the fuel injection system of a diesel engine,
starting becomes impossible. After running out of fuel, or
after disassembling the fuel system, bleed the system
according to the following procedure.
To restart after running out of fuel, turn the switch to the
“ON” position for 15-30 seconds. Try again, if needed. This
unit is equipped with an automatic air bleeding system.
Service Daily
If the engine is operating in very dusty or dry grass
conditions, a clogged air cleaner will result. This can lead to
a loss of power, excessive carbon buildup in the combustion
chamber in high fuel consumption.
Cleaning the Fuel Strainer
Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in gasoline.
Securely fasten the fuel strainer cap so that fuel will not
leak. Check the fuel strainer every 200 hours of operation or
once a month.
Open both cocks located at the crankcase side and at
the lower part of the radiator and drain coolant. Open
the radiator cap while draining. Remove the overflow
tank and drain.
Check hoses for softening and kinks. Check clamps
for signs of leakage.
Flush the radiator by running clean tap water through
radiator until signs of rust and dirt are removed. DO
NOT clean radiator core with any objects, such as a
screwdriver.
Tighten both cocks and replace the overflow tank.
Replace with coolant (see page 40, Table 12 for mixture).
Close radiator cap tightly.
CAUTION :
Allow engine to cool when flushing out
radiator. Flushing the radiator while hot
will damage radiator.
PAGE 48 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — MAINTENANCE
Generator Storage
For storage of the generator for over 30 days, the following
is required:
z Drain the fuel tank completely.
z Completely drain the oil from the crankcase and refill
with fresh oil.
z Clean all external parts of the generator with a cloth.
z Cover the generating set and store in a clean, dry place.
INSPECTION / MAINTENANCE
ENGINE
GENERATOR
10 Hrs
DAILY
Check Engine Fluid Levels
X
Check Air Cleaner
X
Check Battery Acid Level
X
Check Fan Belt Condition
X
Check for Leaks
X
Check for Loosening of Parts
X
250 Hrs
Replace Engine Oil and Filter *1
X
Clean Air Filter
X
Drain Bottom of Fuel Tank
X
Clean Unit, Inside and Outside
X
500 Hrs
Change Fuel Filter *2
X
Clean Radiator and Check Coolant Protection
Level
X
1000 Hrs
Replace Air Filter Element
X
Check all Hoses and Clamps
X
Clean Inside of Fuel Tank
X
Measure Insulation Resistance Over 3M ohms
X
*1 Replace engine oil anf filter at 100 hours, first time only.
*2 Replace fuel filter at 250 Hours, first time only.
PAGE 49 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — GENERATOR WIRING DIAGRAM
PAGE 50 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — ENGINE WIRING DIAGRAM
PAGE 51 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, use the tables shown for
diagnosis based on the Engine Troubleshooting (Table 14). If
the problem cannot be remedied, consult our company's
business office or service plant.
TABLE 14. ENGINE TROUBLESHOOTING
SYMPTOM
Engine does not start.
POSSIBLE PROBLEM
SOLUTION
No fuel?
Replenish fuel.
Air in the fuel system?
Bleed system.
Water in the fuel system?
Remove water from fuel tank.
Fuel pipe clogged?
Clean fuel pipe.
Fuel filter clogged?
Clean or change fuel filter.
Excessively high viscosity of fuel
or engine oil at low temperature?
Use the specified fuel or engine oil.
Fuel with low cetane number?
Use the specified fuel.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Incorrect injection timing?
Adjust.
Fuel cam shaft worn?
Replace.
Injection nozzle clogged?
Clean injection nozzle.
Injection pump malfunctioning?
Repair or replace.
Seizure of crankshaft, camshaft,
piston, cylinder liner or bearing?
Repair or replace.
Compression leak from cylinder?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
Improper valve timing?
Correct or replace timing gear.
Piston ring and liner worn?
Replace.
Excessive valve clearance?
Adjust.
Starter malfunctioning?
Repair or replace.
Wiring disconnected?
Connect wiring.
Starter does not run.
PAGE 52 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — TROUBLESHOOTING (ENGINE)
TABLE 14. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
Engine revolution is not smooth.
Either white or blue exhaust gas
is observed.
Either black or dark gray exhaust
gas is observed.
Deficient output.
POSSIBLE PROBLEM
SOLUTION
Fuel filter clogged or dirty?
Clean or change.
Air cleaner clogged?
Clean or change.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Injection pump malfunctioning?
Repair or replace.
Incorrect nozzle opening
pressure?
Adjust.
Injection nozzle stuck or
clogged?
Repair or replace.
Fuel over flow pipe clogged?
Clean.
Governor malfunctioning?
Repair.
Excessive engine oil?
Reduce to the specified level.
Piston ring and liner worn or
stuck?
Repair or replace.
Incorrect injection timing?
Adjust.
Deficient compression?
Adjust top clearance.
Overload?
Lessen the load.
Low grade fuel used?
Use the specified fuel.
Fuel filter clogged?
Clean or change.
Air cleaner clogged?
Clean or change.
Deficient nozzle injection?
Repair or replace the nozzle.
Incorrect injection timing?
Adjust.
Engine's moving parts seem to
be seizing?
Repair or replace.
Uneven fuel injection?
Repair or replace the injection pump.
Deficient nozzle injection?
Repair or replace the nozzle.
Compression leak?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
PAGE 53 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU — TROUBLESHOOTING (GENERATOR/ENGINE)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, use the tables shown for diagnosis based on the Engine and Radiator Troubleshooting (Table15). If the
problem cannot be remedied, consult our company's business office or service plant.
TABLE 15. GENERATOR TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
SOLUTION
AC Voltmeter defective?
Check output voltage using a voltmeter.
Is wiring connection loose?
Check wiring and repair.
Is AVR defective?
Replace if necessary.
Defective Rotating Rectifier?
Check and replace.
Is engine speed correct?
Turn engine throttle lever to "High".
Is wiring connections loose?
Check wiring and repair.
Defective AVR?
Replace if necessary.
Is wiring connections loose?
Check wiring and repair.
Defective AVR?
Replace if necessary.
Short Circuit in load?
Check load and repair.
Over current?
Confirm load requirements and reduce.
Defective circuit breaker?
Check and replace.
Over current Relay actuated?
Confirm load requirement and replace.
No Voltage Output
Low Voltage Output
High Voltage Output
Circuit Breaker Tripped
PAGE 54 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
NOTE PAGE
PAGE 55 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
*
+, or %, belong to the same assembly or kit.
Note: If more than one of the same reference number is
listed, the last one listed indicates newest (or latest)
part available.
PAGE 56 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU — SUGGESTED SPARE PARTS
DCA-25SSIU W/ISUZU C240 DIESEL ENGINE
1 TO 3 UNITS
Qty.
P/N
Description
10 ............ 0602046356 ............ CIRCUIT BREAKER
20 ............ X132400150 ........... FUEL FILTER
20 ............ 8970246071 ............ OIL FILTER
5 .............. 5136710400 ............ FAN BELT
1 .............. 8943768300 ............ WATER PUMP
2 .............. 9136140430 ............ WATER PUMP GASKET
2 .............. 1823100080 ............ STARTER SWITCH
5 .............. KEYISUZUF ........... STARTER SWITCH KEY
3 .............. 0602122272 ............ OIL SENDING UNIT
2 .............. 5137700221 ............ THERMOSTAT
2 .............. X137130020 ........... THERMOSTAT GASKET
2 .............. 0602014504 ............ RADIATOR HOSE (UPPER)
2 .............. 0602014601 ............ RADIATOR HOSE (LOWER)
1 .............. 0605505070 ............ FUEL CAP
8 .............. 9825119783 ............ GLOW PLUGS
2 .............. 5153110060 ............ INJECTOR NOZZLES
1 .............. 5825500422 ............ EMERGENCY RELAY
1 .............. 5819000200 ............ STOPPER ENGINE
1 .............. 5812003411 ............ ALTERNATOR
1 .............. 8944532120 ............ STARTER
1 .............. 0601820671 ............ AUTOMATIC VOLTAGE REGULATOR
1 .............. 0601808810 ............ MAIN CIRCUIT BREAKER
1 .............. 0601840073 ............ VOLTAGE REGULATOR (RHEOSTAT)
1 .............. M1923100004 ......... SELECTOR SWITCH
1 .............. 47130106 ................ SELECTOR SWITCH KNOB
2 .............. 0601810245 ............ PREHEAT LAMP BULB
NOTE
Part number on this Suggested Spare
Parts list may supercede/replace the
P/N shown in the text pages of this
book.
PAGE 57 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- GENERATOR ASSY.
GENERATOR ASSY.
PAGE 58 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- GENERATOR ASSY.
GENERATOR ASSY.
NO.
PART NO.
1
8351000002
2
3
7961025004
4
0601822630
5
8001070003
6
8351611004
7
8351612004
8
8351615003
9
0105091025
10
0042610000
11
0601000209
12
042006308
13
8351614003
14
0012108025
15
0042508000
16
0012108035
17
0042508000
18
B1130100203
19
0845041904
20
8351350103A
21
0016008045
22
0042508000
23
8351315003
24
011208035
25
8351312004
26
8351331004
27
0017106016
28
0105051045
0012310045
0207010000
030210250
29
30
31
32
33
34
020310080
0012110040
0012310040
0207010000
030210250
8351332004
0010106030
952404470
0605000008
0030012000
0040012000
031112230
ITEM
QTY.
REMARKS
ROTOR ASSY.
1
FIELD ASSY.
1
RECTIFIER
1
SURGE ABSORBER ............................ 1 ........... TNR26G471K
FAN
1
COUPLING DISK
2
WASHER, COUPLING HUB
1
BALANCING PLATE
1
HEX. HEAD BOLT ................................. 4 ........... REPLACES 0010310025
LOCK WASHER
4
BALANCING WEIGHT KIT
1
BEARING .............................................. 1 ........... 6308DDUC3; REPLACES 0071906308
COUPLING RING .................................. 1 ........... REPLACES M1163400103
HEX. HEAD BOLT
6
LOCK WASHER
6
HEX. HEAD BOLT
6
LOCK WASHER
6
STRATOR ASSY.
1
GROMMET
1
FIELD ASSY. EXCITER ........................ 1 ........... REPLACES 8351350103
HEX. SOCKET HAD CAP SCREW
3
LOCK WASHER
3
END BRACKET
1
HEX. HEAD BOLT ................................. 6 ........... REPLACES 0017108035
PACKING
1
COVER, SUCTION
1
HEX. HEAD BOLT
3
HEX. HEAD BOLT ................................. 2 ........... S/N7100001 TO 7102574;
REPLACES 0012110045
HEX. HEAD BOLT ................................. 2 ........... S/N7102575~
HEX. NUT
2
LOCK WASHER
2 ........... S/N7100001 TO 7102574;
REPLACES 0042510000
HEX.NUT .............................................. 2 ........... REPLACES 0030010000
HEX. HEAD BOLT ................................. 4 ........... S/N7100001 TO 7102574
HEX. HEAD BOLT ................................. 4 ........... S/N7102575~
HEX. NUT
4
LOCK WASHER .................................... 4 ........... S/N7100001 TO 7102574;
REPLACES 0042510000
COVER, FAN
1
HEX.HEAD BOLT
1
PLAIN WASHER ................................... 1 ........... REPLACES 0041206000
RUBBER SUSPENSION ....................... 2 ........... EA1009
HEX NUT
2
LOCK WASHER
2
PLAIN WASHER ................................... 2 ........... REPLACES 0041212000
PAGE 59 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- CONTROL BOX ASSY.
CONTROL BOX ASSY.
PAGE 60 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO.
PART NO.
1
2
M1246700514
M1246700524
M1213000202
M1213000212
M1213000222
0601808810
14
15
16
17
18
19
0601808820
021005080
0601842384
0027104010
0601821370
0021004040
0040004000
031104080
0601815925
0027104020
0601823863
0021304015
0601820671
0027105010
0027105015
0601806115
011808015
0601820845
0601820846
M1260600004
0021304015
20
21
22
23
24
0030004000
0027104010
M1213500203
011106015
M1923100004
M1213600104
3
4
5
6
7
8
9
10
11
12
13
ITEM
QTY.
REMARKS
WIRE HARNESS, GENERATOR ................ 1 ......... UP TO S/N7106114
WIRE HARNESS, GENERATOR................ 1 ......... S/N7106115~
CONTROL BOX ......................................... 1 ......... S/N7100001 TO 7102144
CONTROL BOX ......................................... 1 ......... S/N7102145 TO 7102314
CONTROL BOX ......................................... 1 ......... S/N7102315~
CIRCUIT BREAKER .................................. 1 ......... FAF340601021 3P 60A;
UP TO S/N7106114
CIRCUIT BREAKER .................................. 1 ......... S/N7106115~
MACHINE SCREW
4
RESISTOR ................................................. 1 ......... GG20W 50 OHM
MACHINE SCREW
2
RECTIFIER ................................................ 3 ......... DE4503; REPLACES 0601823240
MACHINE SCREW
1
LOCK WASHER
1
PLAIN WASHER ........................................ 1 ......... REPLACES 0041204000
TERMINAL BOARD ................................... 1 ......... 202HB SP
MACHINE SCREW
2
RELAY UNIT .............................................. 2 ......... MSA9013A
MACHINE SCREW .................................... 4 ......... REPLACES 0027104015
AUTOMATIC VOLTAGE REGULATOR ........ 1 ......... NTA5A2DB
MACHINE SCREW .................................... 4 ......... S/N7100001 TO 7102574
MACHINE SCREW .................................... 4 ......... S/N7102575~
CURRENT TRANSFORMER ...................... 3 ......... 812943 50/5A
MACHINE SCREW .................................... 6 ......... REPLACES 0027106015
OVER CURRENT RELAY .......................... 1 ......... LR2D1308
OVER CURRENT RELAY .......................... 1 ......... LR7D1064
FITTING BRACKET ................................... 1 ......... S/N7100001 TO 7102314
MACHINE SCREW .................................... 2 ......... S/N7100001 TO 7102314;
REPLACES 0027104015
HEX. NUT .................................................. 2 ......... REPLACES 0207004000
MACHINE SCREW
2
CONTROL BOX COVER
1
HEX. HEAD BOLT ...................................... 4 ......... REPLACES 0016906015
SELECTOR SWITCH ................................. 1 ......... VY40
SWITCH BRACKET ................................... 1 ......... S/N7100001 TO 7102144
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 61 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- CONTROL BOX ASSY.
CONTROL BOX ASSY.
PAGE 62 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO.
PART NO.
25
26
27
28
29
30
31
32
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
ITEM
QTY.
REMARKS
M1213600114
0027103010
011106015
M1213600004
M1213600014
011106015
SWITCH BRACKET ................................... 1 ......... S/N7102145
MACHINE SCREW
4
HEX. HEAD BOLT ...................................... 4 ......... REPLACES 0016906015
SWITCH COVER................................................ 1 ........ S/N7100001 TO 7102144
SWITCH COVER................................................ 1 ........ S/N7102145~
HEX. HEAD BOLT .............................................. 4 ........ S/N7100001 TO 7102059;
REPLACES 0016906015
011106015
HEX. HEAD BOLT .............................................. 3 ........ S/N7102059~;
REPLACES 0016906015
0016906015
HEX. HEAD BOLT
8
0040506000
TOOTHED WASHER
1
M1223000203 CONTROL PANEL
1
0601807630
FREQUENCY METER,264250DJDJ9; ............... 1 ........ REPLACES 0601807696
UP TO S/N7105234
0601807641
FREQUENCY METER, FCF6 45-65HZ 240V .... 1 ........ FROM S/N7105235~
0601808952
AC AMMETER,260240LSNT1 ........................... 1 ........ REPLACES 0601808991;
UP TO S/N7105234
0601808985
AC AMMETER, ACF60-50A,0-100A/5A ............. 1 ........ FROM S/N7105235~
0601801040
CHANGE-OVER SWITCH, AMMETER .............. 1 ........ SL2AS
0601806813
AC VOLTMETER,260244SJSJ1;........................ 1 ........ REPLACES 0601806896
UP TO S/N7105234
0601806859
AC VOLTMETER, SCF6 0-600V ........................ 1 ........ FROM S/N7105235~
0601801041
CHANGE-OVER SWITCH VOLTMETER ............ 1 ........ SL2VS
0601840073
RHEOSTAT (VOLTAGE REGULATOR) ............... 1 ........ RA20A2SE102BJ 2W 1K OHM
0601840121
KNOB
1
M122310004 STOPPER
1
0027105015
MACHINE SCREW ............................................ 2 ........ S/N7100001 TO 7102674
0027105010
MACHINE SCREW ............................................ 2 ........ S/N7102675~
0027105015
MACHINE SCREW ............................................ 4 ........ S/N7100001 TO 7102674
0027105010
MACHINE SCREW ............................................ 4 ........ S/N7102675~
M9220100004 SET SCREW
1
0080200007
SNAP RING
1
5825500422
EMERGENCY RELAY ....................................... 1 ........ REPLACES 0602200400
06018020132 FUSE
1
011106015
HEX. HEAD BOLT .............................................. 4 ........ REPLACES 0016906015
0330000160
EDGING ............................................................. 2 ........ S/N7100131~
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 63 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
PAGE 64 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
1
M1923200004A ENGINE .......................................... 1 ........... ISUZU QD60(C240) S/N7100001 TO 7102685
M1925200004 ENGINE .......................................... 1 ........... ISUZU QD60(C240) S/N7102686~
5136710400
FAN BELT ....................................... 1 ........... REPLACES 0602011401
2
8970246071
CARTRIDGE, OIL FILTER .............. 1 ........... REPLACES 0602041212
3
X132400150 CARTRIDGE, FUEL FILTER ........... 1 ........... REPLACES 0602042510
4
0602011996
RADIATOR ...................................... 1 ........... C2810010000
5
0602011065
CAP ................................................ 1 ........... C89C0115010
6
011008020
HEX. HEAD BOLT ........................... 6 ........... REPLACES 0016908020
7
0602014504
RADIATOR HOSE, UPER ............... 1 ........... S/N7100001 TO 7101005
M1310500103 RADIATOR HOSE, UPPER ............. 1 ........... S/N7101006~
8
06020146010 RADIATOR HOSE, LOWER ............ 1 ........... S/N7100001 TO 7101005
M1310500203 RADIATOR HOSE, LOWER ............ 1 ........... S/N7101006~
9
0602014334
HOSE BAND ................................... 2 ........... S/N7100001 TO 7100050
0605515147
HOSE BAND ................................... 2 ........... S/N7100051~
10
0602014332
HOSE BAND ................................... 1 ........... S/N7100001 TO 7100050
0605515149
HOSE BAND ................................... 1 ........... S/N7100051~
11
0602014333
HOSE BAND ................................... 1 ........... S/N7100001 TO 7100050
0605515149
HOSE BAND ................................... 1 ........... S/N710051~
12
0602046231
AIR CLEANER ................................ 1 ........... S/N7100001 TO S/N7104749
0602046580
AIR CLEANER ................................ 1 ........... S/N7104750~
0602046356
ELEMENT, AIR CLEANER.............. 1 ........... S/N7100001 TO S/N7104749;
0602046321
ELEMENT, AIR CLEANER
1
S/N7104750~
13
0602040650
INDICATOR, AIR CLEANER ........... 1 ........... S/N7100001 TO S/N7104749
0602040651
INDICATOR, AIR CLEANER ........... 1 ........... S/N7104750~
14
0602040593
BAND, AIR CLEANER .................... 2 ........... S/N7100001 TO 7104749
0602040552
BAND, AIR CLEANER .................... 1 ........... S/N7104750~
15
M1373200003 BRACKET, AIR CLEANER.............. 1 ........... S/N7100001 TO S/N7104749
16
012210025
HEX. HEAD BOLT ........................... 2 ........... S/N7100001 TO S/N7104749;
REPLACES 0016910025
17
011008020
HEX. HEAD BOLT ........................... 4 ........... S/N7100001 TO 7100050;
REPLACES 0016908020
18
0013003008
HEX. HEAD BOLT ........................... 4 ........... S/N7100051 TO S/N7104749
0016908030
HEX. HEAD BOLT ........................... 2 ........... S/N7104750~
19
020108060
HEX. NUT ....................................... 4 ........... S/N7100001 TO 7100050;
REPLACES 0207008000
0036203000
HEX.NUT ........................................ 4 ........... S/N7100051 TO S/N7104749
020108060
HEX.NUT ........................................ 2 ........... S/N7104750~; REPLACES 0207008000
0043003000
LOCK WASHER .............................. 4 ........... S/N710051 TO S/N7104749
0043103000
PLAIN WASHER ............................. 4 ........... S/N7100051 TO S/N7104749
8352032303
HOSE, AIR CLEANER .................... 1 ........... REPLACES M1373100103
20
M137310004 HOSE, AIR CLEANER
1
21
0605515010
HOSE BAND ................................... 3 ........... S/N7100001 TO S/N7100050
060551547
HOSE BAND ................................... 3 ........... S/N7100051~
22
M1303200004 ENGINE FOOT
2
PAGE 65 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
PAGE 66 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
NO.
PART NO.
ITEM
23
24
25
26
27
28
012010030
0207010000
060500006
020701000
M1320200003
M1320300204
29
9095720240
30
31
M1320300104
011206020
32
33
34
35
36
37
0207006000
M9300000003
M9300100003
M1316100204
0229200300
011206020
38
39
40
41
42
43
44
0199100215
0193601450
0605515106
0194500600
0605515003
M1483600503
5819000200
06018020132
011808015
0602220621
0602022560
M1320300304
0602025561
0602022562
0602022792
0602021070
0602021570
0269200660
0603306395
0603306590
0603300285
0605511395
45
46
47
48
49
50
51
52
53
54
55
56
57
QTY.
REMARKS
HEX. HEAD BOLT ................................. 4 ........... REPLACES 0017110030
HEX. NUT
4
RUBBER SUSPENSION ....................... 2 ........... EA1007
HEX. NUT
2
DRAIN PIPE ......................................... 1 ........... S/N7100001 TO S/N7100130
PACKING, OIL PAN SIDE ..................... 1 ........... S/N7100001 TO S/N7100130;
REPLACES M1320300204
PACKING .............................................. 1 ........... S/N7100001 TO S/N7100130;
REPLACES 0602021107
JOINT BOLT ......................................... 1 ........... S/N7100001 TO S/N7100130
HEX. HEAD BOLT ................................. 2 ........... S/N7100001 TO S/N7100130;
REPLACES 0016906020
HEX. NUT ............................................. 2 ........... S/N7100001 TO S/N7100130
RESERVE TANK
1
CAP, RESERVE TANK
1
BRACKET, RESERVE TANK
1
RUBBER CUSHION .............................. 1 ........... S/N7100001 TO S/N7100150
HEX. HEAD BOLT ................................. 1 ........... S/N7100001 TO S/N7100150;
REPLACES 0016906020
HOSE
1
HOSE
1
HOSE BAND ......................................... 1 ........... S/N7100001 TO S/N7100150
HOSE .................................................... 1 ........... S/N7100001 TO S/N7100150
HOSE BAND ......................................... 2 ........... S/N7100001 TO S/N7100150
CLAMP BAR ......................................... 1 ........... REPLACES M1483600103
ENGINE STOPPER .............................. 1 ........... REPLACES 06022108020
FUSE
1
MACHINE SCREW ............................... 3 ........... REPLACES 0027106015
TERMINAL COVER .............................. 1 ........... S/N7100001 TO S/N7100150
ADAPTER ............................................. 1 ........... S/N7100131~
PACKING .............................................. 1 ........... S/N7100131~
90o ELBOW ........................................... 1 ........... S/N7100131~
UNION ................................................... 1 ........... S/N7100131 TO S/N7104749
SWIVEL ................................................ 1 ........... S/N 7100131 TO S/N7104749
CAP ...................................................... 1 ........... S/N 7100131~
DRAIN HOSE ........................................ 1 ........... S/N 7100131 TO S/N7104749
DRAIN HOSE ........................................ 1 ........... S/N7104750~
HOSE JOINT ........................................ 1 ........... S/N7104750~
CONNECTOR ........................................ 1 ........... S/N7104750~
ROCK NUT............................................ 1 ........... S/N7104750~
VALVE ................................................... 1 ........... S/N7104750~
PAGE 67 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
PAGE 68 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
NO.
PART NO.
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
QTY.
REMARKS
M1357200102A
M1354300304
0601840190
020108060
M1354200004
020108060
0605010503
M1354300204
0602180106
020108060
0207006000
0041206000
1823100080
8944626110
0602120095
0602120480
0602122093
0602122272
WIRE HARNESS, ENGINE
1
SLIDE LEVER
1
KNOB .................................................... 1 ........... REPLACES M9320000004
HEX. NUT ............................................. 1 ........... REPLACES 0036003000
BRACKET ............................................. 1 ........... ASK CUST. SVC. FOR COLOR
HEX. NUT ............................................. 1 ........... REPLACES 0030008000
SNAP PIN
1
GOVERNOR ROD
1
BALL JOINT .......................................... 2 ........... LHSA8DE161
HEX. NUT ............................................. 2 ........... REPLACES 0030008000
HEX. NUT
2
PLAIN WASHER
2
STARTER SWITCH ............................... 1 ........... REPLACES 0602100004
PREHEAT LAMP ................................... 1 ........... REPLACES 0602102066
TACHOMETER ...................................... 1 ........... 103680
PICK UP, TACHOMETER ...................... 1 ........... 7154400
OIL PRESSURE GAUGE ...................... 1 ........... 100174
OIL PRESSURE UNIT .......................... 1 ........... 102225; S/N7100001 TO S/N7101239;
REPLACES 0602122207
M9200100004 ADAPTER
1
0602123260
WATER TEMPERATURE GAUGE ......... 1 ........... 100683
0602123201
WATER TEMPERATURE UNIT ............. 1 ........... 0209400
9095720140
PACKING .............................................. 1 ........... REPLACES 0602121109
0602121080
CHARGING AMMETER ....................... 1 ........... 100158
0602128090
FUEL GAUGE ....................................... 1 ........... 100176
0602103092
ALARM LAMP ....................................... 2 ........... PL05
0601810245
BULB ..................................................... 2 ........... E10 T10 DC18V
0601810141
PANEL LIGHT ....................................... 1 ........... ISUZU 9826800370
0601831330
SWITCH, PANEL LIGHT ....................... 1 ........... 900001
020108060
HEX. NUT ............................................. 1 ........... REPLACES 0207008000
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 69 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- OUTPUT TERMINAL ASSY.
OUTPUT TERMINAL ASSY.
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 70 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- OUTPUT TERMINAL ASSY.
OUTPUT TERMINAL ASSY.
NO.
PART NO.
ITEM
QTY
REMARKS
1
8091860103
TERMINAL PANEL................................... 1 ................... REPLACES M1230700003
2
0801830104A OUTPUT TERMINAL BOLT ..................... 5 ................... REPLACES M922000004
3
0801832204
TIE BOLT ................................................. 5 ................... REPLACES M9220000104
4
0039308000
HEX. NUT
10
5
0040008000
LOCK WASHER
15
6
0041408000
PLAIN WASHER
20
7
011606025
HEX. HEAD BOLT .................................... 4 ................... S/N7100001 TO S/N7102674;
REPLACES 0016906025
011206020
HEX. HEAD BOLT .................................... 4 ................... S/N7102675~
8
M1236100303 TERMINAL COVER ................................. 1 ................... S/N7100001 TO S/N7102784
M1236100313 TERMINAL COVER ................................. 1 ................... S/N7102785~
9
M1236100404 OUTPUT WINDOW
1
10
0605010040
HINGE
2
11
0027103010
MACHINE SCREW
4
0207003000
HEX.NUT ................................................. 4 ................... REPLACES 0030003000
58413
PLAIN WASHER ...................................... 4 ................... REPLACES 0041203000
12
011206020
HEX. HEAD BOLT .................................... 2 ................... REPLACES 0016906020
13
011106015
HEX. HEAD BOLT .................................... 4 ................... REPLACES 0016906015
14
M1236400004 CABLE OUTLET COVER
1
15
M1236300004 SUPPORTER, CABLE OUTLET COVER 1
16
011206020
HEX. HEAD BOLT .................................... 6 ................... REPLACES 0016906020
17
0601808804
CIRCUIT BREAKER ................................ 2 ................... QOU250B 2P 50A
18
06018088030 CIRCUIT BREAKER ................................ 2 ................... QOU120B 1P 50A
19
M1260700204 BREAKER FITTING COVER
1
20
0222100115
CUSHION RUBBER
1
21
011206020
HEX. HEAD BOLT .................................... 2 ................... REPLACES 0016906020
22
0601812597
RECEPTACLE .......................................... 2 ................... GF530EM125V 20AX2
REPLACES 0601812549
23
0601811034
RECEPTACLE
2
CA6369 250V 50A ;
REPLACES 0601812538
24
0021304015
MACHINE SCREW .................................. 8 ................... REPLACES 0027104015
0030004000
HEX. NUT ................................................ 8 ................... REPLACES 0207004000
25
M1236100503 TERMINAL COVER
1
26
012212045
HEX.HEAD BOLT .................................... 2 ................... REPLACES 0010112045
27
031112230
PLAIN WASHER ...................................... 2 ................... REPLACES 0041212000
28
M9310200004 STAY RUBBER
2
29
0030012000
HEX. NUT
2
30
0027103010
MACHINE SCREW
4
0207003000
HEX. NUT ................................................ 4 ................... REPLACES 0030003000
PAGE 71 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- BATTERY ASSY.
BATTERY ASSY.
S/N7100001 TO 7100050
S/N7100051~
PAGE 72 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- BATTERY ASSY.
BATTERY ASSY.
NO.
PART NO.
1
2
3
4
5
6
7
8
0602220185
M9310500014
M9103000304
M0602220920
0037808000
0040008000
0040006000
031108160
10
0602220310
M134640004
0602220311
M1346400104
M2346400104
M1346400004
11
M1346400104
12
0016910020
0040510000
9
ITEM
QTY.
REMARKS
BATTERY ....................................... 1 ........... 427MF
BATTERY SHEET
1
BATTERY BAND
1
BATTERY BOLT SET ..................... 2 ........... BHL10J;REPLACES M9103200004
WING NUT ..................................... 2 ........... S/N7100001 TO S/N7100050
LOCK WASHER ............................. 2 ........... S/N7100001 TO S/N7100050
LOCK WASHER ............................. 2 ........... S/N7100051~
PLAIN WASHER ............................ 2 ........... S/N7100001 TO S/N7100050;
REPLACES 0041208000
TERMINAL ASSY. ......................... 1 ........... NO.9P S/N7100001 TO S/N7100050
BATTERY CABLE .......................... 1 ........... S/N7100051~
TERMINAL ASSY. ......................... 1 ........... NO.9P S/N7100001 TO S/N7100050
BATTERY CABLE .......................... 1 ........... S/N7100051 TO S/N7101005
BATTERY CABLE .......................... 1 ........... S/N7101006~
TERMINAL COVER ....................... 1 ........... S/N7100001 TO S/N7100050;
REPLACES M9310000304
TERMINAL COVER ....................... 1 ........... S/N7100001 TO S/N7100050;
REPLACES M9310000204
HEX. HEAD BOLT .......................... 1 ........... S/N7100051~
TOOTHED WASHER ...................... 1 ........... S/N7100051~
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 73 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- MUFFLER ASSY.
MUFFLER ASSY.
S/N7100001 TO S/N7105049
S/N7105050~
PAGE 74 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- MUFFLER ASSY.
MUFFLER ASSY.
NO.
PART NO.
1
1
2
3
0602300160
0602300390
M133040004
011008020
3
4
5
011008020
M1330400104
020108060
031108160
6
7
8
9
10
11
12
13
14
15
16
17
M1333000703
M1333000803
8943811610
M1333200004
M1333200014
9098400850
0040010000
0016908035
M1333000604
0602325021
M1330400204
011106015
0602325020
011008020
ITEM
QTY.
REMARKS
MUFFLER;MAM060249 ................. 1 ........... S/N7100001 TO 7105049
MUFFLER ...................................... 1 ........... S/N7105050~
MUFFLER SUPPORTER ............... 1 ........... S/N7100001 TO 7105049
HEX. HEAD BOLT .......................... 2 ........... REPLACES 0016908020;
S/N7100001 TO 7105049
HEX. HEAD BOLT .......................... 4 ........... REPLACES 0016908020; S/N7105050~
U BOLT
2
S/N7100001 TO 7105049
HEX. NUT ...................................... 4 ........... REPLACES 0037908000;
S/N7100001 TO 7105049
PLAIN WASHER ............................ 4 ........... REPLACES 0041208000;
S/N7100001 TO 7105049
EXHAUST PIPE
1
EXHAUST PIPE ............................. 1 ........... S/N7100001 TO 7105049
GASKET ........................................ 1 ........... REPLACES 0602320102
GASKET ........................................ 1 ........... S/N 7100001 TO S/N7100865
GASKET ........................................ 1 ........... S/N7100866~
HEX. NUT ...................................... 3 ........... REPLACES 0602323001
LOCK WASHER
3
HEX. HEAD BOLT
4
TAIL PIPE ...................................... 1 ........... S/N7100001 TO 7105049
SEAL CLAMP ................................ 1 ........... S/N7100001 TO 7105049
COVER
2
HEX. HEAD BOLT .......................... 4 ........... REPLACES 0016906015
SEAL CLAMP ................................ 1 ........... S/N7100001 TO 7105049
HEX. HEAD BOLT .......................... 4 ........... REPLACES 0016908020;S/N7105050~
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 75 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- FUEL TANK ASSY.
FUEL TANK ASSY.
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 76 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- FUEL TANK ASSY.
FUEL TANK ASSY.
NO.
PART NO.
1
M1363000202
2
0605505070
3
M1363200004
4
M9310500104
5
011008020
6
00379080000
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
ITEM
QTY.
REMARKS
FUEL TANK
1
CAP, FUEL TANK
1
TANK BAND
2
SUPPORTER SHEET
4
HEX. HEAD BOLT .......................... 2 ........... REPLACES 0016908020
HEX. NUT ...................................... 2 ........... S/N7100001 TO S/N7101449;
REPLACES 0037908000
0207308000
HEX. NUT ...................................... 2 ........... S/N7101450~
031108160
PLAIN WASHER ............................ 2 ........... S/N7100001 TO S/N7101449;
REPLACES 0041208000
0222100080
RUBBER SHEET
4
1502025103C DRAIN JOINT ................................ 1 ........... REPLACES M9200000003
M9200200004 DRAIN BOLT
1
0150000018
O RING
1
011206020
HEX. HEAD BOLT .......................... 2 ........... REPLACES 0016906020
M1363400104 DRAIN HOSE
1
06015515198 HOSE BAND .................................. 2 ........... REPLACES 0605515064
0602042420
FUEL FILTER ................................. 1 ........... PTG15P
0602220911
CLAMP
1
0191300730
SUCTION HOSE
1
0191300380
SUCTION HOSE ............................ 1 ........... S/N7100001 TO S/N7102685
0191300920
SUCTION HOSE ............................ 1 ........... S/N7102686~
0191301060
RETURN HOSE
1
0605515109
HOSE BAND .................................. 6 ........... S/N7100001 TO S/N7102685
0605515109
HOSE BAND .................................. 8 ........... S/N7102686~
0191300520
SUCTION HOSE ............................ 1 ........... S/N7102686~
1132008410
WATER SEDIMENTER .................. 1 ........... S/N7102686~; REPLACES 0602042512
0016908025
HEX. HEAD BOLT .......................... 2 ........... S/N7102686~
5154115680
PIPE .............................................. 2 ........... S/N7102686~; REPLACES 0602042660
AND 5154112231
1096751460
JOINT BOLT .................................. 2 ........... S/N7102686~; REPLACES 0602042620
AND 9099063251
9095720140
PACKING ....................................... 4 ........... S/N7102686~; REPLACES 0602042640
PAGE 77 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 78 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
NO.
PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
M1413000212
M1413000222
M1413400004
011008020
M1423000302
M1493100503
M1423000312
M1493100513
011008020
M1423200304
M1493100604
011008020
M1433000203
M1433000303
0010114030
030214350
031114260
M1443000502
011008020
0040508000
M1443300513
M1493300304
M1443300403
M1493300404
0207006000
011008020
011008020
M1443200613
M1443600004
M1443600104
M1443600114
020106050
0027306000
0207306000
952404470
952404470
20
21
952404470
M911300002
0021706015
020106050
ITEM
QTY.
REMARKS
BASE ................................................... 1 .............S/N7100291 TO S/N7104749
REPLACES M1413000202
BASE ................................................... 1 .............S/N7104750~
UNDER COVER
1
HEX. HEAD BOLT ............................... 2 .............REPLACES 0016908020
FRONT FRAME .................................. 1 .............S/N7100001 TO 7105049
ACOUSTIC SHEET ............................ 1 .............S/N7100001 TO 7105049
FRONT FRAME .................................. 1 .............S/N7105050~
ACOUSTIC SHEET ............................ 1 .............S/N7105050~
HEX.HEAD BOLT ................................ 4 .............REPLACES 0016908020
COVER, FRONT FRAME
1
ACOUSTIC SHEET
1
HEX HEAD BOLT .............................. 11 .............REPLACES 0016908020
CENTER FRAME
1
CENTER FRAME
1
HEX. HEAD BOLT
8
LOCK WASHER .................................. 8 .............REPLACES 0040014000
PLAIN WASHER .................................. 8 .............REPLACES 0041214000
REAR FRAME
1
HEX. HEAD BOLT ............................... 4 .............REPLACES 0016908020
TOOTHED WASHER
1
REAR COVER ..................................... 1 .............REPLACES M1443300503
ACOUSTIC SHEET
1
DUCT, REAR COVER
1
ACOUSTIC SHEET
1
HEX. NUT
7
HEX. HEAD BOLT ............................... 6 .............S/N7100001 TO S/N7100290;
REPLACES 0016908020
HEX. HEAD BOLT ............................... 7 .............S/N7100291~; REPLACES 0016908020
REAR DOOR ...................................... 1 .............REPLACES M1443200603
WINDOW PLATE ................................ 1 .............S/N7100001 TO S/N7100725
WINDOW PLATE ................................ 1 .............S/N7100726 TO S/N7101589
WINDOW PLATE ................................ 1 .............S/N7101590~
HEX. NUT ............................................ 6 .............S/N7100001 TO S/N7101449;
REPLACES 0037906000
HEX. NUT ............................................ 6 .............S/N7101450 TO S/N7101589
HEX. NUT ............................................ 8 .............S/N7101590~
PLAIN WASHER ................................ 12 .............S/N7100001 TO S/N7101449;
REPLACES 0041206000
PLAIN WASHER .................................. 6 .............S/N7101450 TO S/N7101589;
REPLACES 0041206000
PLAIN WASHER .................................. 8 .............S/N7101590~; REPLACES 0041206000
DOOR HANDLE ASSY.
1
MACHINE SCREW
4
HEX. NUT ............................................ 4 .............REPLACES 0030006000
PAGE 79 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO INDICATE
COLOR OF UNIT:
5 -BLACK
1-ORANGE
6 -CATERPILLAR YELLOW
2-WHITE
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 80 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
NO.
PART NO.
22
23
24
25
26
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
M9110100204
M9116100004
0021808020
0845031504
M1463000202
M1463000212
M1463000222
M1493500203
M1493500203
011008020
1625165103
1625165204
M1443100202
M1443100212
0016908050
011008020
M1453000703
M1493400904
M1453000903
M1493401004
M1453001003
M1493401104
M1453000803
M1493400804
M1453300503
0207006000
B9114000002
0027106016
020106050
M9110100204
M9110100304
M9116100004
0021808020
0601850097
0027208025
0845031504
0600500090
0021106015
012210025
0040510000
011008020
0040508000
ITEM
QTY.
REMARKS
HINGE
2
WASHER
2
MACHINE SCREW
3
BLIND PLUG ....................................... 2 .............REPLACES M9310000004
ROOF PANEL ..................................... 1 .............S/N7100000 TO S/N7104749
ROOF PANEL ..................................... 1 .............S/N7104750 TO S/N7105049
ROOF PANEL ..................................... 1 .............S/N7105050~
ACOUSTIC SHEET ............................ 1 .............S/N7100000 TO S/N7104749
ACOUSTIC SHEET ............................ 1 .............S/N7104750~
HEX. HEAD BOLT ............................. 18 .............REPLACES 0016908020
BONNET CAP ..................................... 1 .............REPLACES M9310000103
CHAIN ASSY. ....................................... 1 .............REPLACES M1483600204
SPLASHER PANEL ............................. 1 .............S/N7100001 TO S/N7102784
SPLASHER PANEL ............................. 1 .............S/N7102785
HEX. HEAD BOLT
2
HEX. HEAD BOLT ............................... 2 .............REPLACES 0016908020
SIDE DOOR
1
ACOUSTIC SHEET
1
SIDE DOOR
1
ACOUSTIC SHEET
1
SIDE DOOR
1
ACOUSTIC SHEET
1
SIDE DOOR
1
ACOUSTIC SHEET
1
DUCT
1
HEX. NUT
4
DOOR HANDLE ASSY. ....................... 3 .............REPLACES M9113000002
MACHINE SCREW ........................... 12 .............REPLACES 0021806015
HEX. NUT .......................................... 12 .............REPLACES 0030006000
HINGE
4
HINGE
4
WASHER
8
MACHINE SCREW
9
DOOR STOPPER
8
MACHINE SCREW
8
BLIND PLUG ....................................... 8 .............REPLACES M9310000004
EMBLEM
1
MACHINE SCREW
2
HEX. HEAD BOLT ............................... 1 .............REPLACES 0016910025
TOOTHED WASHER
1
HEX. HEAD BOLT ............................... 1 .............REPLACES 0016908020
TOOTHED WASHER
1
PAGE 81 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- RUBBER SEAL ASSY.
RUBBER SEAL ASSY.
S/N7100001 TO 7101589
S/N7101590~
PAGE 82 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- RUBBER SEAL ASSY.
RUBBER SEAL ASSY.
NO.
PART NO.
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
0228910300
0228900725
M1490300004
0228800360
0228900370
0228800605
0229200595
0228900645
0229200750
0229200750
0229200740
0228800670
0228800445
0228800485
0228100568
0228100458
0228100170
0228100171
0228100351
0228100285
0228100153
0228100180
QTY.
RUBBER SEAL
2
RUBBER SEAL
4
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL
2
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL ............................... 3 ...........
RUBBER SEAL ............................... 2 ...........
RUBBER SEAL
1
RUBBER SEAL
2
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL ............................... 2 ...........
RUBBER SEAL ............................... 1 ...........
RUBBER SEAL ............................... 2 ...........
RUBBER SEAL ............................... 1 ...........
RUBBER SEAL ............................... 1 ...........
RUBBER SEAL ............................... 1 ...........
RUBBER SEAL ............................... 1 ...........
RUBBER SEAL ............................... 1 ...........
REMARKS
S/N7100001 TO S/N7101589
S/N7101590~
S/N7100001 TO S/N7101589
S/N7101590~
S/N7100001 TO S/N7101589
S/N7101590~
S/N7101590~
S/N7101590~
S/N7101590~
S/N7101590~
PAGE 83 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
DCA-25SSIU --- DECALS
DECAL ASSY.
PAGE 84 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
DCA-25SSIU --- DECALS
DECAL ASSY.
NO.
PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
M1550000003
M1550000104
M1550000204
M1550000303
M1550000403
M9500000004
M9500100004
M9500300004
M9500300104
M9500500004
M9500500104
M9503000004
M9503000103
M9503100004
M9503200004
M9510100004
M9520100503
18
M9520100503
19
20
21
22
23
24
M9510200002
M9520000004
M9520000104
M9520000204
M9520100004
M9520100503
25
26
27
28
29
30
31
32
33
34
35
M9520100503
M9520100204
M9520100304
M9520100404
M9520200003
M9520200104
M1560100403
M1560100303
M1560100004
M1560100504
M1560100104
M1560100204
ITEM
QTY.
REMARKS
DECAL; ENGINE OPERATING ..............................1 ..... M15000000
DECAL; NOTE ........................................................ 1 ..... M15000010
DECAL; NOTE ........................................................ 1 ..... M15000020
DECAL; AUXILLARY OUTPUT ............................... 1 ..... M15000030
DECAL; GENERATOR CONTROL .......................... 1 ..... M15000040
DECAL; OIL DRAIN PLUG .....................................1 ..... M90000000
DECAL; WATER .....................................................1 ..... M90010000
DECAL; - ................................................................ 1 ..... M90030000
DECAL; + ............................................................... 1 ..... M90030010
DECAL; DIESEL FUEL .......................................... 1 ..... M90050000
DECAL; FUEL DRAIN PLUG ..................................1 ..... M90050010
DECAL; WARNING .................................................2 ..... M90300000
DECAL; WATER, OIL CHECK ................................1 ..... M90300000
DECAL; WARNING .................................................1 ..... M90310000
DECAL; WARNING .................................................1 ..... M90320000
DECAL; CAUTION ..................................................1 ..... M91010000
DECAL; WARNING .................................................1 ..... S/N7100001 TO 7100600;
REPLACES M9510100104
DECAL; WARNING .................................................1 ..... S/N7100001 TO 7100600;
REPLACES M9510100204
DECAL; MQ ...........................................................1 ..... M91020000
DECAL; GROUND ..................................................1 ..... M92000000
DECAL; AMMETER CHANGE OVER SWITCH ..... 1 ..... M92000010
DECAL; VOLTMETER CHANGE OVER SWITCH ..1 ..... M92000020
DECAL; WARNING .................................................2 ..... M92010000
DECAL; WARNING .................................................1 ..... S/N7100001 TO 7100600;
REPLACES M9520100104
DECAL; WARNING .................................................1 ..... M92010050 M9100601~
DECAL; CAUTION ..................................................1 ..... M92010020A
DECAL; SAFETY INSTRUCTIONS ........................ 1 ..... M92010030
DECAL; DANGER ..................................................1 ..... M92010040
DECAL; CONNECTION OF OUTPUT CABLE ....... 1 ..... M92020000
DECAL; OVER CURRENT RELAY ......................... 1 ..... M92020010
STRIPE;WHISPERWATT
1
STRIPE; MQ POWER
2
STRIPE;
3
STRIPE; 25
2
STRIPE
1
STRIPE
1
PAGE 85 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- CYLINDER HEAD AND COVER ASSY.
CYLINDER HEAD AND COVER ASSY.
PAGE 86 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- CYLINDER HEAD AND COVER ASSY.
CYLINDER HEAD AND COVER ASSY.
NO.
PART NO.
ITEM
1
5111102070
CYLINDER HEAD ASSY.
3
1096000051
SEALING CUP, RR FACE D=44
3-1
5111290060
SEALING CUP, LOWER D=16
3-2
5112190080
SEALING CUP, UPPER D=18
3-3
5096000130
SEALING CUP, DRILLED D=12
4
9098605220
PLUG; LOWER CYLINDER HEAD PLATE
7
5117150230
VALVE SEAT INLET INSERT
8
5117110260
VALVE SEAT EXHAUST INSERT
9
5117210160
VALVE INLET HEAD GUIDE
9-1
5117210160
VALVE EXHAUST HEAD GUIDE
11
5111501080
HOT PLUG ASSY.
14
5125690060
INLET AND EXHAUST VALVE SEAL
16
9041108350
MANIFOLD STUD
16-1 9041108400
MAINFOLD STUD
16-2 9041108450
MANIFOLD STUD
21
5111410690
CYLINDER HEAD GASKET
22
5090090530
BOLT
29
5111702400
CYLINDER HEAD COVER ASSY.
30
9117510381
OIL FILLER CAP
31
5111790520
BREATHER NIPPLE
49
5111730170
HEAD COVER PACKING
51
9111798080
HEAD COVER FIX. PACKING
52
9111791320
WAHER
54
5090000960
BOLT
60
5096050050
CYLINDER HEAD OIL COOLER PLUG
QTY.
1
1
4
5
4
4
4
4
4
4
4
8
3
3
1
1
19
1
1
1
1
2
2
2
1
REMARKS
PAGE 87 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- CYLINDER BLOCK ASSY.
CYLINDER BLOCK ASSY.
PAGE 88 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- CYLINDER BLOCK ASSY.
CYLINDER BLOCK ASSY.
NO.
PART NO.
ITEM
1
2
4
4-1
5
6
6-1
6-2
6-3
6-4
7
8
9
10
11-1
12-1
13-1
26
27-1
28
29
31
32
36
37
42-1
42-2
43
46
47-1
52
54-2
55
56
58-2
59
64-1
66
67
69
77
78
81
84
99
117
120
121
130
131
5112101771
9098025910
9096640340
5112190080
5116100010
5112190180
5112190170
5112190150
5096000130
1096000051
9112612300
8942505140
5111290060
5112210020
5096050161
9992023160
9095714160
5096500210
9112976500
9113111530
5113120110
9081510240
9019008220
9099022990
9081610320
9019008180
9019008220
9099168160
5112920110
9097040380
9098785970
8942008311
9099138340
9112290490
5117400211
9099210990
9097130870
9099152380
9019008180
9091645080
9123631120
5096250360
9113411940
5090002270
9112581080
5117490340
9019008180
9019608180
9092023080
9095714080
QTY.
REMARKS
CYLINDER BLOCK ASSY.
1
BOLT
10
PLUG; 1/2 TAPPET CHAMBER
2
SEALING CUP CHAMBER D=18
2
BEARING KIT; CAM. STANDARD
1
SEALING CUP RR FACE D=36
1
SEALING CUP RR FACE D=38
1
SEALING CUP LH SIDE D=32
2
SEALING CUP RR FACE D=12
1
SEALING CUP LH SIDE D=45
3
CYLINDER LINER
4
PLUG; CAMSHAFT BRIDGE PLATE
1
PLUG; OIL GALLERY PLATE
2
DUCT; CYL. BLOCK WATER
1
PLUG; OIL GALLERY 1/8
1
PLUG; OIL GALLERY SCREW
1
PLUG PACKING
1
INJ. PUMP OIL FEED NIPPLE
1
TAPPET CHAMBER COVER ASSY.
1
FRONT CYL. BLOCK PLATE
1
FRONT PLATE PACKING
1
FRONT PLATE STRAIGHT PIN
2
BOLT
3
ROCKER OIL FEED NIPPLE
1
REAR PLATE STRAIGHT PIN
1
BOLT
12
BOLT
2
TAPPET CHAMBER COVER CLIP
2
CHAMBER COVER PACKING ......................... 1 .......... REPLACES 5112920150
WATER DRAIN COCK
1
CRANK CASE PIN
2
BOLT
1
PIPE; VINYL WATER DRAIN
1
CYLINDER BLOCK DOWEL
2
BREATHER AIR ASSY.
1
BREATHER PACKING
1
PIPE; VINYL BREATHER
1
CLIP
1
BOLT
1
WASHER
1
SPACER; OIL SEAL
1
CRANK SHAFT REAR SEAL
1
REAR CYLINDER BLOCK PLATE
1
BOLT
3
OIL PAN BRIDGE CAP PACKING
2
BREATHER HEAD PACKING
1
BOLT
2
BOLT
1
PLUG; OIL GALLERY SCREW
1
SCREW PLUG PACKING
1
PAGE 89 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 ---TIMING GEAR ASSY.
TIMING GEAR ASSY.
PAGE 90 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- TIMING GEAR ASSY.
TIMING GEAR ASSY.
NO.
PART NO.
1
5113110282
2
9113211480
3
9099206010
4
901906140
8
9113120460
9
5096250790
12
9113270450
14
9113120340
17
9019108320
ITEM
TIMING GEAR CASE
GEAR CASE COVER
PACKING
BOLT
PACKING
OIL SEAL
POINTER
PACKING
BOLT
QTY.
1
1
1
4
2
1
1
1
9
REMARKS
PAGE 91 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 FLYWHEEL HOUSING ASSY.
FLYWHEEL HOUSING ASSY.
PAGE 92 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 FLYWHEEL HOUSING ASSY.
FLYWHEEL HOUSING
NO.
PART NO.
1-5
5113410191
11
9113430391
12
9019006120
21
5113490380
22
5113490370
23
9019110200
23-1 9019110180
31
9019310450
41
9019110350
41
9010560400
42
9091104100
46
9091505100
ASSY.
ITEM
FLYWHEEL HOUSING
COVER
BOLT
STIFFENER; RIGHT SIDE
STIFFENER; LEFT SIDE
BOLT
BOLT
BOLT
BOLT
BOLT
NUT
LOCK WASHER
QTY.
1
1
6
1
1
2
2
4
3
1
2
2
REMARKS
PAGE 93 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 OIL PAN ASSY.
OIL PAN ASSY.
PAGE 94 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 OIL PAN ASSY.
OIL PAN ASSY.
NO.
PART NO.
1-2
5113601832
3*
5096050050
3-1
9992023200
4-1*
9097205600
6
9112150810
17
5113670040
24
9992023160
26
9095714160
29
9019106160
31
9112193160
32
9030906160
36
9117606090
42
9019008220
42-1 9019708450
51
5117400870
52#
5117410100
53#
5117500021
56
9099207080
57
9019008200
ITEM
QTY.
REMARKS
OIL PAN ASSY. ................................ 1 ................ INCL. ITEMS W/*
OIL DRAIN PLUG, 3/8
1
OIL DRAIN PLUG
1
O RING PACKING
1
CRANK CASE
1
OIL CASE PACKING
1
OIL THERMO PLUG
1
PLUG PACKING
1
BOLT
30
DISTRIBUTION PLATE
1
SCREW
4
OIL LEVEL GAUGE
1
BOLT
16
BOLT
4
OIL FILLER ASSY. ........................... 1 ................ INCL. ITEMS W/#
OIL FILLER
1
OIL FILLER CAP
1
PACKING
1
BOLT
2
PAGE 95 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 ---OIL PUMP ASSY.
OIL PUMP ASSY.
PAGE 96 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 ---OIL PUMP ASSY.
OIL PUMP ASSY.
NO.
PART NO.
ITEM
1
6*
8*#
11*#
12*
13*
14*
15*
16*
21*
22*%
41
OIL PUMP ASSY. ................................. 1 ........... INCL. ITEMS W/*
ROTOR SET .......................................... 1 ........... INCL. ITEMS W/#
PIN
1
PIN
1
PINION
1
COVER
1
BOLT
4
LOCK WASHER
4
LOCK WASHER
4
OIL STRAINER ASSY. .......................... 1 ........... INCL. ITEM W/%
OIL STRAINER GAUZE
1
BOLT
2
9131008010
5131200040
9131290170
9098780840
9131280790
9131130771
9020408250
9091505080
9091505080
9131401200
9131430100
9019708250
QTY.
REMARKS
PAGE 97 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- CRANKSHAFT, BRIDGE AND FLYWHEEL ASSY.
CRANKSHAFT, BRIDGE AND FLYWHEEL ASSY.
PAGE 98 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- CRANKSHAFT, BRIDGE AND FLYWHEEL ASSY.
CRANKSHAFT, BRIDGE AND FLYWHEEL ASSY.
NO.
PART NO.
ITEM
QTY
REMARKS
1
5115100211
CRANK BEARING KIT;STD
1
1-1
5115300211
CRANK BEARING KIT;-0.25
1
1-2
5115400211
CRANK BEARING KIT;-0.50
1
2
9115810570
THRUST BEARING
2
3
5121112020
PISTON;STD
4
4
5121210070
PISTON RING SET;STD
4
6
5122110090
PISTON PIN
4
7
5095870010
SNAP RING
8
8-1
5122300390
CONNECTING ROD ASSY. .................... 4 ..................... INCL. ITEMS W/@
9-1@ 5122510050
SMALL END BUSHING
4
11-1@ 512350090
BOLT
8
12@ 5094090160
NUT
8
13
8941422080
CONN. ROD BEARING SET;STD ........... 4 .................... REPLACES 5122710050
13-1 8941631740
BEARING SET;-0.25
4
13-2 8941631750
BEARING SET;-0.50
4
14
8941396690
CRANKSHAFT ASSY. ............................ 1 .................... INCL. ITEM W/#
15#
9081612200
STRAIGHT PIN
1
17
5098010010
RADIAL BALL BEARING
1
25-1 5123301100
FLYWHEEL ASSY. .................................. 1 .................... INCL. ITEM W/%
27% 9123330361
RING GEAR ............................................ 1 .................... Z=108
31
9098785320
STRAIGHT PIN
2
33
5090001461
BOLT
6
34
5123360100
WASHER
1
36
9080307430
FEATHER KEY
1
37
9125210420
CRANKSHAFT GEAR ............................. 1 .................... Z=21
38
9123620390
THROWER
1
60-1 9123736051
CRANKSHAFT PULLEY
1
64-1 9098026060
BOLT
1
67
9123736060
THROWER
1
69
9123790160
WASHER
1
PAGE 99 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- OIL AND FUEL FILTER ASSY.
OIL AND FUEL FILTER ASSY.
PAGE 100 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- OIL AND FUEL FILTER ASSY.
OIL AND FUEL FILTER
NO.
PART NO.
2
9885131071
3*
9132130350
4
9099211920
5-1
9099209780
6*
9099221100
7
9132121240
8
9099410540
9
9132390330
10
9132316030
11
9098621170
12
9132110950
13
9132390320
14
9099522170
23
9132260130
24
9099208410
25
9098640150
26
5132600080
27% 1096231630
28
5131600030
29#
9099209750
70
8941434770
72$
8941434790
77$
9095720140
80$
5132120750
86$
9132600561
91
9197518010
92
9020608180
93
9091506080
94
9091645080
96
9019110320
100
9132190570
101-1 9019008350
110
8941208540
111@ 8941564550
112@ 8941564540
113@ 9132260090
114@ 5131600030
115@ 9099206200
ASSY.
ITEM
QTY.
REMARKS
OIL FILTER ELEMENT KIT ........ 1 .............. INCL. ITEMS W/*
O RING PACKING COVER
1
CENTER PIPE PACKING
1
DRAIN PIPE PACKING
1
FELT RING
1
OIL FILTER COVER
1
COIL COMPRESSION SPRING 1
SPRING SEAT
1
CENTER PIPE
1
DRAIN PLUG
1
OIL FILTER BODY
1
ELEMENT HOLDER
1
SNAP RING
1
ADAPTER
1
PLUG PACKING
1
SCREW PLUG
1
SAFETY VALVE ASSY. .............. 1 .............. INCL. ITEM W/%
O RING PACKING
1
RELIEF VALVE ASSY. ................ 1 .............. INCL. ITEM W/#
RELIEF VALE PACKING
1
FUEL CART. FILTER ASSY. ....... 1 .............. INCL. ITEMS W/$
FUEL ELEMENT
1
OVERFLOW VALVE PACKING 2
FUEL FILTER COVER
1
OVERFLOW VALVE ASSY.
1
FUEL FILTER BRACKET
1
BOLT
2
LOCK WASHER .......................... 2 .............. REPLACES 9091508080
PLAIN WASHER
2
BOLT
2
OIL FILTER PACKING
1
BOLT
4
OIL FILTER ASSY. ...................... 1 .............. INCL. ITEMS W/@
OIL FILTER CARTRIDGE
1
OIL FILTER BODY
1
ADAPTER
1
RELIEF VALVE ASSY.
1
PACKING ADAPTER
1
PAGE 101 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- OIL PIPE ASSY.
OIL PIPE ASSY.
PAGE 102 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- OIL PIPE ASSY.
OIL PIPE ASSY.
NO.
PART NO.
1
9133119810
2
5133111141
3
9099061051
4
9099209000
9
5133111740
10
5096750220
11
9095720080
13
901906120
ITEM
OIL PUMP ASSY.
ROCKER OIL FEED PIPE
BOLT
PACKING
OIL INJECTION PIPE
ADAPTER
PACKING
BOLT
QTY.
1
1
1
2
1
1
2
1
REMARKS
PAGE 103 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- WATER PUMP AND FAN ASSY.
WATER PUMP AND FAN ASSY.
PAGE 104 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- WATER PUMP AND FAN ASSY.
WATER PUMP AND FAN ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
1
5136101673
WATER PUMP ASSY. ................... 1 ............ INCL. ITEMS W/*
3*
5878101391
WATER PUMP REPAIR KIT .......... 1 ............ INCL. ITEMS W.#
5136310080
BEARING UNIT
1
6*#
7*#
9136210760
IMPELLER
1
9136136070
PACKING
1
8*#
9*#
8942366870
SEAL UNIT ASSY.
1
SCREW HEATER PLUG
1
10*# 5096050050
11*# 5098140010
SCREW
1
LOCK WASHER
1
12*# 9091505080
13*# 5136420640
FAN CENTER
1
WATER PUMP COVER
1
16*# 9136120530
18*# 9030408160
SCREW
1
24*# 9136390010
BRIDGE UNIT THROWER
1
31
9136140430
PACKING
1
33
5090000890
BOLT
2
33-1 5090000880
BOLT
4
41
5136750390
ADJUSTING FAN BELT PLATE 1
50
9136416160
FAN PULLEY
1
51
9136420770
FAN SPACER
1
54
9136608090
FAN ASSY.
1
59
9019108450
BOLT
4
64
5136710400
COOLING FAN BELT
1
71
9137130380
OUTLET PIPE
1
72
5137700221
THERMOSTAT
1
73
5096050050
HEATER PLUG
1
76
5096370130
PACKING
1
77
9019708300
BOLT
2
78
9099168190
CLIP
1
90
9137168042
THERMOSTAT HOUSING
1
91
5137430050
HOUSING PACKING
1
92
9019708200
BOLT
2
92
9019108220
BOLT
2
93
9137211322
RUBBER BYPASS HOSE
1
94
9099156441
HOSE CLIP
2
PAGE 105 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- INTAKE AND EXHAUST MANIFOLD ASSY.
INTAKE AND EXHAUST MAINIFOLD ASSY.
PAGE 106 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- INTAKE AND EXHAUST MANIFOLD ASSY.
INTAKE AND EXHAUST MANIFOLD ASSY.
NO.
PART NO.
ITEM
1
3
20
21
30
46
48
49
51
52
66
76
77
78
83
97
9141126954
9041108500
9141416142
5093020020
5141111290
5141460180
9091646080
9091505080
9091104080
5090000870
5143101961
5096370150
9091104080
9091505080
5093600530
5143340780
INLET MANIFOLD
INTAKE STUD
EXHAUST MANIFOLD
EXHAUST STUD
INLET PIPE
GASKET
PLAIN WASHER
LOCK WASHER
NUT
BOLT
INTAKE SHUTTER ASSY.
THROTTLE VALVE PACKING
NUT
LOCK WASHER
HOSE
WIRE CONTROL BRACKET
QTY.
REMARKS
1
2
1
1
2
1
7
7
7
2
1
3
3
2
1
1
PAGE 107 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 108 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
PART NO.
3
5142102130
5*
5142150140
5142110670
27*
38*
9142191410
5142120560
59*
76*
5142170040
9142170620
81*
82*# 9142191770
200
9142176020
ITEM
QTY.
REMARKS
AIR CLEANER ASSY. ................... 1 ............ INCL. ITEMS W/*
ELEMENT
1
COVER
1
INDICATOR
1
DUST W/BAFFLE PAN
1
CLAMP
1
BOLT W/GASKET WASHER ......... 1 ............ INCL. ITEMS W/#
GASKET WASHER
3
BAND ASSY. W/BOLT
2
PAGE 109 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- ENGINE FOOT ASSY.
ENGINE FOOT ASSY.
PAGE 110 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- ENGINE FOOT ASSY.
ENGINE FOOT ASSY.
NO.
PART NO.
ITEM
1
1-1
6
6-1
6-2
8
11
30
31
32
33
34
36
37
38
39
40
41
41-1
42
43
44
46
47
51
52
52-1
9117712070
5117710501
9029510250
9029510250
9029560400
9098518660
5197110010
9091505080
9091114080
9091605120
9829315110
9019312450
9010558320
9019108400
9091647080
9091505080
9091605080
9117770750
9117771360
9141491730
9091105080
5197190060
9091104080
9091505080
5113190570
8942059870
9019108320
ENGINE FOOT, RIGHT SIDE
ENGINE FOOT, LEFT SIDE
FOOT BOLT, RIGHT SIDE
BOLT FOOT, LEFT SIDE
BOLT FOOT, LEFT SIDE
PLAIN WASHER
ALTERNATOR BRACKET
LOCK WASHER
NUT
PLAIN WASHER
CABLE ASSY.
BOLT
BOLT
BOLT
PLAIN WASHER
LOCK WASHER
PLAIN WASHER
FRONT LIFTING HANGER
REAR LIFTING HANGER
REAR HANGER PIECE
NUT
ALTERNATOR FAN COVER
NUT
LOCK WASHER
FRONT PLATE PACKING
BOLT
BOLT
QTY.
REMARKS
1
1
4
1
3
8
1
1
1
1
1
2
2
1
1
2
2
1
1
2
2
1
1
1
1
2
4
PAGE 111 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- INJECTION PUMP ASSY.
INJECTION PUMP ASSY.
PAGE 112 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- INJECTION PUMP ASSY.
INJECTION PUMP ASSY.
NO.
PART NO.
ITEM
5
8943864440
15*
20*
35*
38*
40*
42*
5157201400
8941415340
5157400720
9197510790
9099205760
5125240660
QTY.
REMARKS
INJECTION PUMP ASSY. .................... 1 ..................... REPLACES 5156010252
INCL. ITEMS W/*
GOVERNOR ASSY.
1
FEED PUMP ASSY.
1
AUTOMATIC TIMER
1
INJ. PUMP SPACER BRACKET
1
O RING PACKING
1
INJ. PUMP GEAR
1
PAGE 113 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- ELECTRICAL PARTS
ELECTRICAL PARTS
PAGE 114 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- ELECTRICAL PARTS
ELECTRICAL PARTS
NO.
PART NO.
1
2
4
8
12
14
19
20
21
23
30
34
36
38-1
50
51
5811000801
5812003410
9822007640
9822531070
9829317430
9825119780
9825301090
9829513240
9829513250
9829513320
9197326100
5824500140
5825500190
1823100080
1823170070
9091114080
9091505080
ITEM
QTY.
REMARKS
STARTER
1
ALTERNATOR .................................... 1 ......................... UP TO OCT. 1992
ALTERNATOR .................................... 1 ......................... OCT. 1992~
REGULATOR
1
CABLE ASSY.
1
GLOW PLUG
4
CONTROL
1
INSULATOR CAP
2
INSULATOR CAP
2
CABLE CAP
1
CONNECTOR
1
SWITCH
1
EMERGENCY RELAY
1
STARTER SWITCH
1
KEY
1
NUT
1
LOCK WASHER
1
PAGE 115 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- ACCESSORIES
ACCESSORIES
PAGE 116 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- ACCESSORIES
ACCESSORIES
NO.
PART NO.
ITEM
50
51*
52*
53*
54*
56*
58*
59*
61*
66
67
91
91-1
DRIVE ASSY. ....................................... 1 ..................... INCL. ITEMS W/*
CASE
1
COVER
1
PACKING
1
GEAR
1
GEAR
1
BOLT
4
NIPPLE
1
OIL SEAL
1
BOLT
2
PACKING
1
STOPPER ASSY.
1
CABLE ASSY.
1
5193100060
9193110240
9193110200
9193120060
9193160270
9193160170
9019006160
9090310100
9099243550
9019008220
9099211070
5819000020
5828480360
QTY.
REMARKS
PAGE 117 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 ---INJECTION PUMP COMP. ASSY.
INJECTION PUMP COMP. ASSY.
PAGE 118 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- INJECTION PUMP COMP. ASSY.
INJECTION PUMP COMP. ASSY.
NO.
PART NO.
ITEM
5
15*
16*
18*
20*
21*
22*
23*
24*
27*
28*
29*
31*
32*
34*
35*
36*
40*
43*
45*#
47*#
48*#
49*#
55*
55-1*
55-2*
55-3*
55-4*
55-5*
55-6*
55-7*
55-8*
55-9*
55-10*
55-11*
55-12*
55-13*
55-14*
55-15*
55-16*
55-17*
55-18*
55-19*
55-20*
5156110460
9812151150
9812350170
1156190240
1156390080
1156390080
5156120080
1156190030
9812151440
9091505060
9091104060
1096230130
5156310090
9812411030
5156430020
9812450140
5156440050
5156490160
9812212230
9812212200
1156220030
1156290010
5156190410
5156190340
5156190350
5156190360
5156190010
5156190020
5156190030
5156190040
5156190050
5156190070
5156190080
5156190090
5156190100
5156190110
5156190120
5156190130
5156190150
9812350420
9812350430
9812350440
9812350450
5156190250
QTY.
REMARKS
HOUSING ASSY. .................................. 1 ..................... INCL. ITEMS W/*
STUD
3
ADAPTER
1
BOLT
2
GASKET
1
GASKET
1
COVER
1
SCREW
2
GASKET
2
LOCK WASHER
3
NUT
3
PACKING
1
PLUNGER ASSY.
4
DELIVERY VALVE
4
DELIVERY VALVE SPRING
4
GASKET
4
HOLDER
4
PLATE ASSY.
2
TAPPET ASSY. ..................................... 4 ..................... INCL. ITEMS W/#
PIN TAPPET
4
TAPPET ROLLER
4
TAPPET BUSHING
4
TAPPET GUIDE
4
TAPPET SHIM .................................. A/R ..................... T=0.30
TAPPET SHIM .................................. A/R ..................... T=0.40
TAPPET SHIM .................................. A/R ..................... T=0.50
TAPPET SHIM .................................. A/R ..................... T=0.60
TAPPET SHIM .................................. A/R ..................... T=0.70
TAPPET SHIM .................................. A/R ..................... T=0.80
TAPPET SHIM .................................. A/R ..................... T=0.90
TAPPET SHIM .................................. A/R ..................... T=1.00
TAPPET SHIM .................................. A/R ..................... T=1.10
TAPPET SHIM .................................. A/R ..................... T=1.20
TAPPET SHIM .................................. A/R ..................... T=1.30
TAPPET SHIM .................................. A/R ..................... T=1.40
TAPPET SHIM .................................. A/R ..................... T=0.55
TAPPET SHIM .................................. A/R ..................... T=0.65
TAPPET SHIM .................................. A/R ..................... T=0.75
TAPPET SHIM .................................. A/R ..................... T=0.85
TAPPET SHIM .................................. A/R ..................... T=0.95
TAPPET SHIM .................................. A/R ..................... T=1.05
TAPPET SHIM .................................. A/R ..................... T=1.15
TAPPET SHIM .................................. A/R ..................... T=1.25
TAPPET SHIM .................................. A/R ..................... T=0.25
PAGE 119 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- INJECTION PUMP COMP. ASSY.
INJECTION PUMP COMP. ASSY.
PAGE 120 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- INJECTION PUMP COMP. ASSY.
INJECTION PUMP COMP. ASSY.
NO.
PART NO.
ITEM
55-21*
55-22*
55-23*
55-24*
55-25*
55-26*
55-27*
55-28*
57*
58*
59*
60*
61*
62*
66*
67*
75*
73*
76-2*
77*
77-2*
82*
83*
84*
84-1*
84-2*
84-3*
84-4*
84-5*
84-6*
84-7*
84-8*
84-9*
85*
85-1*
85-2*
85-3*
85-4*
85-5*
85-6*
85-7*
85-8*
85-9*
93*
95*
5156190260
5156190270
5156190370
5156191060
5156191070
5156191080
5156191090
5156191100
9812314070
9812350150
9812350210
9812250580
9812250570
9812350030
5156370020
1156390030
5156210170
9812232010
9000906770
9812232010
9000906770
9812250470
9812250470
5156290150
5156290160
5156290170
5156290180
5156290190
5156290200
5156190380
5156290210
5156190390
1156190900
5156290150
5156290160
5156290170
5156290180
5156290190
5156290200
5156190380
5156290210
5156190390
1156190900
5156290050
9019006140
QTY.
REMARKS
TAPPET SHIM ................................ A/R ....................... T=0.26
TAPPET SHIM ................................ A/R ....................... T=0.35
TAPPET SHIM ................................ A/R ....................... T=0.45
TAPPET SHIM ................................ A/R ....................... T=1.50
TAPPET SHIM ................................ A/R ....................... T=1.60
TAPPET SHIM ................................ A/R ....................... T=1.35
TAPPET SHIM ................................ A/R ....................... T=1.45
TAPPET SHIM ................................ A/R ....................... T=1.55
PLUNGER SPRING
4
PLUNGER SEAT
4
PLUNGER SEAT
4
SLEEVE
4
PINION
4
SCREW
4
CONTROL RACK
1
SCREW
1
CAM SHAFT
1
BALL BEARING, CAMSHAFT
1
BALL BEARING, CAMSHAFT
1
BALL BEARING, GOV. SIDE
1
BALL BEARING, GOV. SIDE
1
CAMSHAFT RING
1
CAM RING, GOV. SIDE
1
CAMSHAFT SHIM .......................... A/R ....................... T=0.10
CAMSHAFT SHIM .......................... A/R ....................... T=0.12
CAMSHAFT SHIM .......................... A/R ....................... T=0.14
CAMSHAFT SHIM .......................... A/R ....................... T=0.16
CAMSHAFT SHIM .......................... A/R ....................... T=0.18
CAMSHAFT SHIM .......................... A/R ....................... T=0.50
CAMSHAFT SHIM .......................... A/R ....................... T=1.00
CAMSHAFT SHIM .......................... A/R ....................... T=0.30
CAMSHAFT SHIM .......................... A/R ....................... T=0.70
CAMSHAFT SHIM .......................... A/R ....................... T=1.40
CAMSHAFT SHIM .......................... A/R ....................... T=0.10
CAMSHAFT SHIM .......................... A/R ....................... T=0.30
CAMSHAFT SHIM .......................... A/R ....................... T=0.14
CAMSHAFT SHIM .......................... A/R ....................... T=0.16
CAMSHAFT SHIM .......................... A/R ....................... T=0.18
CAMSHAFT SHIM .......................... A/R ....................... T=0.50
CAMSHAFT SHIM .......................... A/R ....................... T=1.00
CAMSHAFT SHIM .......................... A/R ....................... T=0.30
CAMSHAFT SHIM .......................... A/R ....................... T=0.70
CAMSHAFT SHIM .......................... A/R ....................... T=1.40
HOUSING COVER
1
BOLT
4
PAGE 121 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- INJECTION PUMP COMP. ASSY.
INJECTION PUMP COMP. ASSY.
PAGE 122 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- INJECTION PUMP COMP. ASSY.
INJECTION PUMP COMP. ASSY.
NO.
PART NO.
ITEM
108* 9812214110
KEY
111* 1156190820
BOLT
PACKING
113* 1157590010
137* 9097060370
BOLT
PACKING
138* 1096350070
150* 9812150780
TAPPET PLUG
PLAIN WASHER
162* 9091606100
163* 9091505100
LOCK WASHER
NUT
164* 5156390020
180* 9197510790
BRACKET
O RING PACKING
181* 9099205760
QTY.
1
1
2
1
2
4
4
4
4
1
1
REMARKS
PAGE 123 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 ---GOVERNOR COMP. ASSY.
GOVERNOR COMP. ASSY.
PAGE 124 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- GOVERNOR COMP. ASSY.
COVERNOR COMP. ASSY.
NO.
PART NO.
ITEM
5
12*
13*
14*
15*
16*
18*
19*
20*
26*
27*
30*
32*
34*
35*
36*
40*
42*
43*
44*
47*
50*
52*
53*
54*
57*
58*#
60*
60-1*
60-2*
60-3*
63*
64*
67*
68*
69*
73*
74*
77*
80*
81*
82*
1157210040
1157290150
9813150650
9019008180
9813253970
901906140
5157291230
9813252370
1157290380
9813251820
9813261120
5157210080
5157290530
5157290540
5157290330
5157291230
9813211860
9813919070
5157290630
9019006160
9812350340
9813213230
5156190490
5157290340
9813250860
5157190080
9000902290
9813250880
9813255510
9813255520
9813255530
9813222100
5157230820
1157230200
9813932040
1156390080
9813216360
9008130230
9813217210
9813250990
9813212050
9091854150
QTY.
REMARKS
HOUSING ............................................. 1 ..................... INCL. ITEMS W/*
O RING PACKING
1
ADAPTER
1
BOLT
1
HOUSING PLATE
1
BOLT
6
SCREW
1
NUT
2
HOUSING PLUG
1
SCREW
1
NUT
1
COVER
1
PLUG
2
BOLT
2
BOLT
2
SCREW
1
COVER
1
O RING PACKING
1
BOLT
2
BOLT
2
CAP
1
FLYWEIGHT ASSY.
1
KEY
1
LOCK WASHER
1
NUT
1
SLEEVE ................................................ 1 ..................... INCL. ITEM W/#
BEARING
1
SHIM ................................................. A/R ..................... T=0.20
SHIM ................................................. A/R ..................... T=0.30
SHIM ................................................. A/R ..................... T=0.40
SHIM ................................................. A/R ..................... T=1.00
GOVERNOR SPRING
1
LINK SPRING
1
CAPSULE SPRING
1
NUT
1
GASKET
2
CAPSULE SPRING
1
NUT
1
LEVER
1
BUSHING
2
O RING PACKING
2
SNAP RING
2
PAGE 125 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- GOVERNOR COMP. ASSY.
GOVERNOR COMP. ASSY.
PAGE 126 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- GOVERNOR COMP. ASSY.
GOVERNOR COMP. ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
83*
9813212200
OIL SEAL
1
84*
9813251730
SHIM ..................................................... 1 ..................... T=0.50
85*
9813250970
SHIM ................................................. A/R ..................... T=0.30
86*
9813253180
PLUG
1
88*
9813250300
KEY
1
89*
9813913070
COLLAR
1
90*
9813254880
WASHER
A/R
93*
5157250160
GUIDE LEVER ASSY.
1
100* 9813217130
LINK
1
101* 1157290230
SNAP RING
1
102* 5157250170
TENSION LEVER
1
103* 9813250620
PIN
1
104* 5157250490
LEVER
1
116* 1157290010
GASKET
1
117* 1157290020
GASKET
1
148* 5157291120
BOLT
1
150* 5157230880
SPRING
1
PAGE 127 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- FEED PUMP COMP. ASSY.
FEED PUMP COMP. ASSY.
PAGE 128 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- FEED PUMP COMP. ASSY.
FEED PUMP COMP. ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
5
5157510120
HOUSING ........................................... 1 ....................... INCL. ITEMS W/*
9*
9813512050
PISTON
1
10*
9813513030
SPRING
1
11*
9813550230
PLUG
1
12*
9813550350
GASKET
1
15*
5157540010
TAPPET ASSY. ................................... 1 ....................... INCL. ITEMS W/*
16*# 9813514030
ROLLER
1
17*# 9813514100
PIN
1
18*# 1157590020
GUIDE
2
26*
9813516020
CHECK VALVE
2
27*
1096230160
GASKET
1
28*
9813517020
SPRING
2
31*
9099063260
BOLT
1
32*
1156190820
BOLT
1
33*
1157590010
PACKING
4
35*
1157590030
ADAPTER
1
40*
1096230160
PACKING
1
42*
9813550250
RING
1
44*
9813521040
PUMP ................................................. 1 ....................... REPLACES 5157610050
45*
9813550330
COVER
1
PAGE 129 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- AUTO TIMER COMP. ASSY.
AUTO TIMER COMP. ASSY.
PAGE 130 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- AUTO TIMER COMP. ASSY.
AUTO TIMER COMP. ASSY.
NO.
PART NO.
ITEM
5
6*
6-1*
6-2*
6-3*
6-4*
6-5*
6-6*
6-7*
6-8*
6-9*
7*
11*
12*
12-1*
12-2*
12-3*
12-4*
12-5*
12-6*
12-7*
12-8*
13*
14*
15*
17*
20-1*
21*
26*
27*
28*
9813435050
9813450430
9813450440
9813450450
5157490090
5157490100
5157490110
5157490680
5157490690
5157490700
5157490710
9813450720
9813453380
9813453250
9813453260
9813453400
9813453270
9813453280
9813453290
9813453300
9813453310
9813453320
5157490070
9813450520
9813453060
5125240660
5156190480
1156190010
5157490080
9813433050
5157490280
QTY.
REMARKS
FLYWEIGHT .................................. 2.............................. INCL. ITEMS W/*
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
TIMER SPRING
2
WASHER
1
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
SHIM
A/R
WASHER
1
PLATE
1
NUT
1
GEAR
1
LOCK WASHER
1
NUT
1
BOLT
6
FLANGE
1
HOLDER
1
PAGE 131 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- NOZZLE HOLDER COMP. ASSY.
NOZZLE HOLDER COMP. ASSY.
PAGE 132 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- NOZZLE HOLDER COMP. ASSY.
NOZZLE HOLDER COMP. ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
5
5153410020
PUSH ROD ......................................... 4 ....................... INCL. ITEMS W/*
7*
5153430020
SPRING
4
9*
9153396010
SCREW
4
11*
5153340030
NUT
4
12*
9153390560
GASKET
4
13*
9153390570
WASHER
4
21*
9153326030
NUT
4
22*
9153520050
GASKET
4
23*
9153510070
CONNECTOR
4
31*
5153490010
BOLT
4
32*
9095714080
GASKET
8
38*
9153596010
SCREW
4
PAGE 133 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 ---STARTER COMP. ASSY.
STARTER COMP. ASSY.
PAGE 134 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- STARTER COMP. ASSY.
STARTER COMP. ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
6
5811210160
ARMATURE ASSY. .................................... 1 ................ INCL. ITEMS W/*
13*
5811291050
PINION STOPPER
1
14*
5811290030
WASHER SET
1
22*
5811120100
FIELD COIL ASSY. .................................... 1 ................ INCL. ITEM W/>
25*> 5811160480
BRUSH, +
1
30*
5811150130
REAR COVER ASSY. ................................ 1 ................ INCL. ITEM W/%
32*% 5811190120
REAR METAL
1
33*
5811160180
BRUSH HOLDER ....................................... 1 ................ INCL. ITEMS W/@
35*@ 5811170060
BRUSH SPRING
4
37*@ 5811160490
BRUSH, 2
50*
5811190130
BRACKET ASSY. ...................................... 1 ................ INCL. ITEM W/&
52*& 9821121340
CENTER METAL
1
55*
5811230070
CLUTCH ASSY.
1
65*
5811130170
GEAR CASE ASSY. .................................. 1 ................ INCL. ITEM W/#
66*# 5811190260
FRONT METAL
1
67*
5811290680
DUST COVER
1
75*
5811270130
SHIFT LEVER ASSY.
1
80*
5811510290
MAGNETIC SWITCH ASSY.
1
85*
5811290710
BOLT
2
86*
5811290730
WASHER
2
PAGE 135 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 --- ALTERNATOR COMP. ASSY.
ALTERNATOR COMP. ASSY. (OCT. 1992~)
PAGE 136 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- ALTERNATOR COMP. ASSY.
ALTERNATOR COMP. ASSY. (OCT. 1992~)
NO.
PART NO.
ITEM
3
4*>
5*
7*
8*#
9*#
10*#%
11*#%
12*#%
13*#%
14*#
17*
18*&
19*&
22*&
23*
24*
26*
27*
5812210630
9000901810
5812110580
5812141310
5812141320
5812190360
5812150460
5812291660
5812150400
5812700040
5812620050
5812130430
5812290290
5098000870
5812291650
5812220760
9822350150
5812291820
5812291830
QTY.
REMARKS
ROTOR ASSY. ........................................................ 1 ..... INCL. ITEMS W/* AND W/>
BALL BEARING
1
STRATOR ASSY.
1
REAR COVER ASSY. ............................................ 1 ..... INCL. ITEMS W/#
REAR COVER
1
BRUSH REGULATOR .............................................1 ..... INCL. ITEMS W/%
BRUSH ASSY.
1
BOLT
2
BRUSH
2
REGULATOR ASSY.
1
RECTIFIER
1
FRONT COVER ASSY. .......................................... 1 ..... INCL. ITEMS W/&
RETAINER
1
BALL BEARING
1
SCREW KIT
1
PULLEY ASSY.
1
NUT
1
BOLT
2
BOLT
1
PAGE 137 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
ISUZU C240 ---ALTERNATOR COMP. ASSY.
ALTERNATOR COMP. ASSY. (BEFORE OCT. 1992)
PAGE 138 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
ISUZU C240 --- ALTERNATOR COMP. ASSY.
ALTERNATOR COMP. ASSY. (BEFORE OCT. 1992)
NO.
PART NO.
ITEM
5
8*
18*
20*
25*
27*#
30*#
33*#
34*#
35*#
39*#
50*
52*&
53*&
54*&
55*&
75*
80*
90*
91*
5812210100
9000901810
9822250270
5812110090
5812140010
9822316190
5812150010
9822316170
9822316180
9822350700
9822319040
9822313080
9822158230
9822158240
9822159170
9000901820
5812220140
9822350740
9822350720
9822350730
QTY.
REMARKS
ROTOR ASSY. ....................................................... 1 ..... INCL. ITEMS W/*
BALL BEARING
1
KEY
1
STRATOR ASSY.
1
COVER ASSY. ....................................................... 1 ..... INCL. ITEMS W/#
RECTIFIER ASSY.
1
HOLDER ASSY.
1
BRUSH
1
BRUSH
1
BOLT ASSY.
1
RECTIFIER COVER
1
FRONT COVER ASSY. .......................................... 1 ..... INCL. ITEMS W/&
PACKING
1
RETAINER
1
RETAINER BRIDGE
1
FRONT BALL BEARING
1
PULLEY ASSY.
1
NUT
1
BOLT ...................................................................... 2 ..... L=85
BOLT ...................................................................... 2 ..... L=95
PAGE 139 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
TERMS AND CONDITIONS OF SALE — PARTS
Effective: July 1, 2000
4.
PAYMENT TERMS
Terms of payment for parts are net 10 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and the
carrier.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
5.
Parts must be in new and resalable
condition, in the original Multiquip package
(if any), and with Muiltiquip part numbers
clearly marked.
6.
The following items are not returnable:
a.
Obsolete parts. (If an item is listed
in the parts price book as being
replaced by another item, it is
obsolete.)
b.
Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
MINIMUM ORDER
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c.
Any line item with an extended dealer
net price of less than $5.00.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a specific
date and all orders received on or after that date
will be billed at the revised price. Rebates for
price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.
Multiquip reserves the right to quote and sell
direct to Government agencies, and to Original
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
SPECIAL EXPEDITING SERVICE
A $20.00 to $50.00 surcharge will be added to
the invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
d.
Special order items.
RETURNED GOODS POLICY
e.
Electrical components.
Return shipments will be accepted and credit
will be allowed, subject to the following
provisions:
f.
Paint, chemicals, and lubricants.
LIMITATIONS OF SELLER’S LIABILITY
g.
Decals and paper products.
1.
h.
Items purchased in kits.
Multiquip shall not be liable here under for
damages in excess of the purchase price of the
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
2.
A Returned Material Authorization must
be approved by Multiquip prior to shipment.
To obtain a Return Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
a.
b.
The list must be typed or computer
generated.
c.
The list must state the reason(s) for
the return.
d.
The list must reference the sales
order(s) or invoice(s) under which
the items were originally purchased.
e.
3.
The parts numbers and descriptions
must match the current parts price
list.
The list must include the name and
phone number of the person
requesting the RMA.
A copy of the Return Material
Authorization must accompany the return
shipment.
7.
The sender will be notified of any material
received that is not acceptable.
8.
Such material will be held for 5 working
days from notification, pending
instructions. If a reply is not received
within 5 days, the material will be returned
to the sender at his expense.
9.
Credit on returned parts will be issued at
dealer net price at time of the original
purchase, less a 15% restocking charge.
10. In cases where an item is accepted for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
11. Credit issued will be applied to future
purchases only.
LIMITATION OF WARRANTIES
No warranties, express or implied, are made
in connection with the sale of parts or trade
accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes not
authorizes any person to assume for it any
other obligation or liability whatever in
connection with the sale of its products. A part
from such written statement of warranty, there
are no warranties, express, implied or statutory,
which extend beyond the description of the
products on the face hereof.
PAGE 140 — DCA-25SSIU — PARTS AND OPERATION MANUAL(STD) — REV. #3 (09/17/01)
NOTE PAGE
PAGE 141 — DCA-25SSIU — PARTS AND OPERATION MANUAL (STD) — REV. #3 (09/17/01)
PARTS AND OPERATION MANUAL
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
© COPYRIGHT 2001, MULTIQUIP INC.
PARTS DEPARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
SERVICE DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEPARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
MULTIQUIP INC.
PARTS DEPARTMENT:
18910 WILMINGTON AVE.
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
SERVICE DEPARTMENT:
310-537-3700
800-421-1244
800-835-2551
FAX: 310-537-3927
FAX: 310-638-8046
E-mail:mq@multiquip.com • www:multiquip.com
Download PDF